GPIO19 can not output high level.

Robotics & Edge Computing Jetson & Embedded Systems Jetson AGX Xavier
1

GPIO19(SOC_GPIO43/K56/GPIO3_PQ.07) used to control the power on our design carrier board.
Using oscilloscope to measure it, it’s always low when set it to high.
It can not output high level.

I set this pin as output pin.

pinmux@2430000 {
                pinmux_default: common {

                        soc_gpio43_pq7 {
                                nvidia,pins = "soc_gpio43_pq7";
                                nvidia,function = "rsvd2";
                                nvidia,pull = <TEGRA_PIN_PULL_NONE>;
                                nvidia,tristate = <TEGRA_PIN_DISABLE>;
                                nvidia,enable-input = <TEGRA_PIN_DISABLE>;
                        /*
                                nvidia,io-high-voltage = <TEGRA_PIN_ENABLE>;
                                nvidia,lpdr = <TEGRA_PIN_DISABLE>;
                        */
                        };

                };

        };

        gpio@2200000 {
                fusb302-vbus-enable {
                        gpio-hog;
                        output-high;
                        gpios = <TEGRA194_MAIN_GPIO(Q, 7) 0>;
                        label = "usbP10";
                        status = "okay";
                };
        };

        fixed-regulators {
                fusb302_vbus_en: regulator@116 {
                        compatible = "regulator-fixed";
                        reg = <116>;
                        regulator-name = "usb-p10-vdd";
                        regulator-min-microvolt = <5000000>;
                        regulator-max-microvolt = <5000000>;
                        gpio = <&tegra_main_gpio TEGRA194_MAIN_GPIO(Q, 7) 0>;
                        enable-active-high;
                        vin-supply = <&battery_reg>;
                };
		
        };

I can see it’s high in OS.

cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 288-511, parent: platform/2200000.gpio, tegra-gpio:
......................
......................
 gpio-417 (                    |int-gpio            ) in  hi
 gpio-420 (                    |usbP10-switch       ) out hi
 gpio-423 (                    |fusb302_vbus_en     ) out lo
 gpio-480 (                    |bt_host_wake        ) in  hi
......................

cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 288-511, parent: platform/2200000.gpio, tegra-gpio:
......................
......................
 gpio-417 (                    |int-gpio            ) in  hi
 gpio-420 (                    |usbP10-switch       ) out hi
<b> gpio-423 (                    |fusb302_vbus_en     ) out hi</b>
 gpio-480 (                    |bt_host_wake        ) in  hi
......................

PINMUX looks normal

cat tegra_pinctrl_reg
......................
Bank: 0 Reg: 0x02430020 Val: 0x00000022 -> soc_gpio40_pq4
Bank: 0 Reg: 0x02430028 Val: 0x00000401 -> soc_gpio41_pq5
Bank: 0 Reg: 0x02430030 Val: 0x0000005a -> soc_gpio42_pq6
<b>Bank: 0 Reg: 0x02430038 Val: 0x00000022 -> soc_gpio43_pq7</b>
......................
Bank: 0 Reg: 0x02430040 Val: 0x00000056 -> soc_gpio44_pr0
Bank: 0 Reg: 0x02430048 Val: 0x00000415 -> soc_gpio45_pr1
......................

cat pinctrl/2430000.pinmux/pinmux-pins
 ......................
pin 127 (SOC_GPIO07_PP7): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 128 (SOC_GPIO20_PQ0): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 129 (SOC_GPIO21_PQ1): (MUX UNCLAIMED) tegra-gpio:417
pin 130 (SOC_GPIO22_PQ2): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 131 (SOC_GPIO23_PQ3): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 132 (SOC_GPIO40_PQ4): (MUX UNCLAIMED) tegra-gpio:420
pin 133 (SOC_GPIO41_PQ5): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 134 (SOC_GPIO42_PQ6): (MUX UNCLAIMED) (GPIO UNCLAIMED)
<b>pin 135 (SOC_GPIO43_PQ7): (MUX UNCLAIMED) tegra-gpio:423</b>
......................
pin 136 (SOC_GPIO44_PR0): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 137 (SOC_GPIO45_PR1): (MUX UNCLAIMED) (GPIO UNCLAIMED)
 ......................
2

Do you mean the regulator have no effect? How about removing the regulator first and only using sysfs to toggle the GPIO? Could you see the value change under such case?

3

Hi,WayneWWW

I had removed the regulator, and I can operate this io in sysfs.

root@gcs-desktop:/sys/class/gpio# ls
export  gpiochip240  gpiochip248  gpiochip288  unexport
root@gcs-desktop:/sys/class/gpio# echo 423 > export
root@gcs-desktop:/sys/class/gpio# ls
export  gpio423  gpiochip240  gpiochip248  gpiochip288  unexport
root@gcs-desktop:/sys/class/gpio# echo out > gpio423/direction

root@gcs-desktop:/sys/class/gpio# cat gpio423/value
0
root@gcs-desktop:/sys/class/gpio# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 288-511, parent: platform/2200000.gpio, tegra-gpio:
........................
........................
 gpio-417 (                    |fusb302-int-input   ) in  hi
 gpio-420 (                    |usbP10-switch       ) out hi
<b> gpio-423 (                    |sysfs               ) out lo</b>
 gpio-480 (                    |bt_host_wake        ) in  hi
 gpio-489 (                    |int-gpio            ) in  hi

root@gcs-desktop:/sys/class/gpio# echo 1 > gpio423/value
root@gcs-desktop:/sys/class/gpio# cat gpio423/value
1
root@gcs-desktop:/sys/class/gpio# cat /sys/kernel/debug/gpio
........................
........................
 gpio-417 (                    |fusb302-int-input   ) in  hi
 gpio-420 (                    |usbP10-switch       ) out hi
<b> gpio-423 (                    |sysfs               ) out hi</b>
 gpio-480 (                    |bt_host_wake        ) in  hi
 gpio-489 (                    |int-gpio            ) in  hi

It looks normal in OS,but I still can’t measure the voltage.
I’ve replaced two Xavier modules and two carrier boards for test this.

4

Please review your hardware first. Also, please try to use the pinmux spreadsheet too. Why do you want to set it directly in dts?

5

Used the pinmux spreadsheet to creat the .cfg file,the problem still exists.

We have measure GPIO19 test point to connector-K56 is direct Connection, and we disconnect the post-circuit from GPIO19 test point .

##
## Pinmux version 1.0
## Input pinmux file name: tegra19x-1001-pinmux.dtsi
## Input gpio file name: tegra19x-1001-gpio-default.dtsi
## Generation date: 2019-08-15 09:53
## PLEASE DO NOT EDIT THIS FILE
## This is autogenerated file using the script pinmux-dts2cfg.py
##
pinmux.major = 1;
pinmux.minor = 0;
#### Pinmux for gpio-input pins ####
pinmux.0x022136a0 = 0x00000001; # CONFIG S5
pinmux.0x02431018 = 0x00000000; # GPIO soc_gpio30_ps5
pinmux.0x022136e0 = 0x00000001; # CONFIG S7
pinmux.0x02431008 = 0x00000000; # GPIO soc_gpio32_ps7
pinmux.0x02213800 = 0x00000001; # CONFIG T0
pinmux.0x02431000 = 0x00000000; # GPIO soc_gpio33_pt0
pinmux.0x02213860 = 0x00000001; # CONFIG T3
pinmux.0x02431050 = 0x00000000; # GPIO dap3_din_pt3
pinmux.0x02214000 = 0x00000001; # CONFIG G0
pinmux.0x02434058 = 0x00000000; # GPIO soc_gpio00_pg0
pinmux.0x02214020 = 0x00000001; # CONFIG G1
pinmux.0x02434050 = 0x00000000; # GPIO soc_gpio01_pg1
pinmux.0x02214040 = 0x00000001; # CONFIG G2
pinmux.0x02434048 = 0x00000000; # GPIO soc_gpio02_pg2
pinmux.0x02214060 = 0x00000001; # CONFIG G3
pinmux.0x02434040 = 0x00000000; # GPIO soc_gpio03_pg3
pinmux.0x02214080 = 0x00000001; # CONFIG G4
pinmux.0x02434070 = 0x00000000; # GPIO soc_gpio08_pg4
pinmux.0x022140e0 = 0x00000001; # CONFIG G7
pinmux.0x02434088 = 0x00000000; # GPIO soc_gpio11_pg7
pinmux.0x02214200 = 0x00000001; # CONFIG H0
pinmux.0x02434090 = 0x00000000; # GPIO soc_gpio12_ph0
pinmux.0x02214240 = 0x00000001; # CONFIG H2
pinmux.0x024340a0 = 0x00000000; # GPIO soc_gpio14_ph2
pinmux.0x022142e0 = 0x00000001; # CONFIG H7
pinmux.0x02434018 = 0x00000000; # GPIO dap2_sclk_ph7
pinmux.0x02214400 = 0x00000001; # CONFIG I0
pinmux.0x02434008 = 0x00000000; # GPIO dap2_dout_pi0
pinmux.0x02214420 = 0x00000001; # CONFIG I1
pinmux.0x02434000 = 0x00000000; # GPIO dap2_din_pi1
pinmux.0x02214440 = 0x00000001; # CONFIG I2
pinmux.0x02434010 = 0x00000000; # GPIO dap2_fs_pi2
pinmux.0x02212420 = 0x00000001; # CONFIG Z1
pinmux.0x0243d0b0 = 0x00000000; # GPIO usb_vbus_en0_pz1
pinmux.0x02212460 = 0x00000001; # CONFIG Z3
pinmux.0x0243d040 = 0x00000000; # GPIO spi1_sck_pz3
pinmux.0x02212480 = 0x00000001; # CONFIG Z4
pinmux.0x0243d020 = 0x00000000; # GPIO spi1_miso_pz4
pinmux.0x022124a0 = 0x00000001; # CONFIG Z5
pinmux.0x0243d058 = 0x00000000; # GPIO spi1_mosi_pz5
pinmux.0x022124c0 = 0x00000001; # CONFIG Z6
pinmux.0x0243d010 = 0x00000000; # GPIO spi1_cs0_pz6
pinmux.0x022124e0 = 0x00000001; # CONFIG Z7
pinmux.0x0243d050 = 0x00000000; # GPIO spi1_cs1_pz7
pinmux.0x0c2f1000 = 0x00000001; # CONFIG EE0
pinmux.0x0c301010 = 0x00000000; # GPIO safe_state_pee0
pinmux.0x0c2f1080 = 0x00000001; # CONFIG EE4
pinmux.0x0c301038 = 0x00000000; # GPIO power_on_pee4
pinmux.0x0c2f1600 = 0x00000001; # CONFIG AA0
pinmux.0x0c303000 = 0x00000000; # GPIO can1_dout_paa0
pinmux.0x0c2f1620 = 0x00000001; # CONFIG AA1
pinmux.0x0c303008 = 0x00000000; # GPIO can1_din_paa1
pinmux.0x0c2f1640 = 0x00000001; # CONFIG AA2
pinmux.0x0c303010 = 0x00000000; # GPIO can0_dout_paa2
pinmux.0x0c2f1660 = 0x00000001; # CONFIG AA3
pinmux.0x0c303018 = 0x00000000; # GPIO can0_din_paa3
pinmux.0x0c2f16e0 = 0x00000001; # CONFIG AA7
pinmux.0x0c303038 = 0x00000000; # GPIO can0_err_paa7
pinmux.0x02212ac0 = 0x00000001; # CONFIG P6
pinmux.0x02430080 = 0x00000000; # GPIO soc_gpio06_pp6
pinmux.0x02212c00 = 0x00000001; # CONFIG Q0
pinmux.0x02430050 = 0x00000000; # GPIO soc_gpio20_pq0
pinmux.0x02212c20 = 0x00000001; # CONFIG Q1
pinmux.0x02430058 = 0x00000000; # GPIO soc_gpio21_pq1
pinmux.0x02212cc0 = 0x00000001; # CONFIG Q6
pinmux.0x02430030 = 0x00000000; # GPIO soc_gpio42_pq6
pinmux.0x02212e00 = 0x00000001; # CONFIG R0
pinmux.0x02430040 = 0x00000000; # GPIO soc_gpio44_pr0
pinmux.0x02212e80 = 0x00000001; # CONFIG R4
pinmux.0x02430098 = 0x00000000; # GPIO uart1_rts_pr4
pinmux.0x02212ea0 = 0x00000001; # CONFIG R5
pinmux.0x02430090 = 0x00000000; # GPIO uart1_cts_pr5
pinmux.0x02211440 = 0x00000001; # CONFIG A2
pinmux.0x02432008 = 0x00000000; # GPIO dap6_din_pa2
pinmux.0x02213240 = 0x00000001; # CONFIG L2
pinmux.0x02437008 = 0x00000000; # GPIO pex_wake_n_pl2
pinmux.0x02212820 = 0x00000001; # CONFIG N1
pinmux.0x02440020 = 0x00000000; # GPIO soc_gpio54_pn1
pinmux.0x02212840 = 0x00000001; # CONFIG N2
pinmux.0x02440028 = 0x00000000; # GPIO soc_gpio55_pn2
#### Pinmux for gpio-output-low pins ####
pinmux.0x02213880 = 0x00000003; # CONFIG T4
pinmux.0x0221388c = 0x00000000; # CONTROL T4
pinmux.0x02213890 = 0x00000000; # OUTPUT T4
pinmux.0x02431048 = 0x00000000; # GPIO dap3_fs_pt4
pinmux.0x022138a0 = 0x00000003; # CONFIG T5
pinmux.0x022138ac = 0x00000000; # CONTROL T5
pinmux.0x022138b0 = 0x00000000; # OUTPUT T5
pinmux.0x02431080 = 0x00000000; # GPIO dap5_sclk_pt5
pinmux.0x022138c0 = 0x00000003; # CONFIG T6
pinmux.0x022138cc = 0x00000000; # CONTROL T6
pinmux.0x022138d0 = 0x00000000; # OUTPUT T6
pinmux.0x02431078 = 0x00000000; # GPIO dap5_dout_pt6
pinmux.0x022140a0 = 0x00000003; # CONFIG G5
pinmux.0x022140ac = 0x00000000; # CONTROL G5
pinmux.0x022140b0 = 0x00000000; # OUTPUT G5
pinmux.0x02434078 = 0x00000000; # GPIO soc_gpio09_pg5
pinmux.0x02212000 = 0x00000003; # CONFIG X0
pinmux.0x0221200c = 0x00000000; # CONTROL X0
pinmux.0x02212010 = 0x00000000; # OUTPUT X0
pinmux.0x0243d000 = 0x00000000; # GPIO gpu_pwr_req_px0
pinmux.0x02212020 = 0x00000003; # CONFIG X1
pinmux.0x0221202c = 0x00000000; # CONTROL X1
pinmux.0x02212030 = 0x00000000; # OUTPUT X1
pinmux.0x0243d068 = 0x00000000; # GPIO cv_pwr_req_px1
pinmux.0x02212220 = 0x00000003; # CONFIG Y1
pinmux.0x0221222c = 0x00000000; # CONTROL Y1
pinmux.0x02212230 = 0x00000000; # OUTPUT Y1
pinmux.0x0243d008 = 0x00000000; # GPIO spi3_miso_py1
pinmux.0x02212280 = 0x00000003; # CONFIG Y4
pinmux.0x0221228c = 0x00000000; # CONTROL Y4
pinmux.0x02212290 = 0x00000000; # OUTPUT Y4
pinmux.0x0243d028 = 0x00000000; # GPIO spi3_cs1_py4
pinmux.0x02212440 = 0x00000003; # CONFIG Z2
pinmux.0x0221244c = 0x00000000; # CONTROL Z2
pinmux.0x02212450 = 0x00000000; # OUTPUT Z2
pinmux.0x0243d0b8 = 0x00000000; # GPIO usb_vbus_en1_pz2
pinmux.0x0c2f16a0 = 0x00000003; # CONFIG AA5
pinmux.0x0c2f16ac = 0x00000000; # CONTROL AA5
pinmux.0x0c2f16b0 = 0x00000000; # OUTPUT AA5
pinmux.0x0c303028 = 0x00000000; # GPIO can0_en_paa5
pinmux.0x0c2f16c0 = 0x00000003; # CONFIG AA6
pinmux.0x0c2f16cc = 0x00000000; # CONTROL AA6
pinmux.0x0c2f16d0 = 0x00000000; # OUTPUT AA6
pinmux.0x0c303030 = 0x00000000; # GPIO can0_wake_paa6
pinmux.0x0c2f1800 = 0x00000003; # CONFIG BB0
pinmux.0x0c2f180c = 0x00000000; # CONTROL BB0
pinmux.0x0c2f1810 = 0x00000000; # OUTPUT BB0
pinmux.0x0c303040 = 0x00000000; # GPIO can1_stb_pbb0
pinmux.0x0c2f1820 = 0x00000003; # CONFIG BB1
pinmux.0x0c2f182c = 0x00000000; # CONTROL BB1
pinmux.0x0c2f1830 = 0x00000000; # OUTPUT BB1
pinmux.0x0c303048 = 0x00000000; # GPIO can1_en_pbb1
pinmux.0x0c2f1840 = 0x00000003; # CONFIG BB2
pinmux.0x0c2f184c = 0x00000000; # CONTROL BB2
pinmux.0x0c2f1850 = 0x00000000; # OUTPUT BB2
pinmux.0x0c303050 = 0x00000000; # GPIO can1_wake_pbb2
pinmux.0x02212c80 = 0x00000003; # CONFIG Q4
pinmux.0x02212c8c = 0x00000000; # CONTROL Q4
pinmux.0x02212c90 = 0x00000000; # OUTPUT Q4
pinmux.0x02430020 = 0x00000000; # GPIO soc_gpio40_pq4
pinmux.0x02212ce0 = 0x00000003; # CONFIG Q7
pinmux.0x02212cec = 0x00000000; # CONTROL Q7
pinmux.0x02212cf0 = 0x00000000; # OUTPUT Q7
pinmux.0x02430038 = 0x00000000; # GPIO soc_gpio43_pq7
pinmux.0x02211420 = 0x00000003; # CONFIG A1
pinmux.0x0221142c = 0x00000000; # CONTROL A1
pinmux.0x02211430 = 0x00000000; # OUTPUT A1
pinmux.0x02432010 = 0x00000000; # GPIO dap6_dout_pa1
pinmux.0x02214e00 = 0x00000003; # CONFIG B0
pinmux.0x02214e0c = 0x00000000; # CONTROL B0
pinmux.0x02214e10 = 0x00000000; # OUTPUT B0
pinmux.0x02446008 = 0x00000000; # GPIO cpu_pwr_req_0_pb0
pinmux.0x02214e20 = 0x00000003; # CONFIG B1
pinmux.0x02214e2c = 0x00000000; # CONTROL B1
pinmux.0x02214e30 = 0x00000000; # OUTPUT B1
pinmux.0x02446000 = 0x00000000; # GPIO cpu_pwr_req_1_pb1
pinmux.0x02212660 = 0x00000003; # CONFIG M3
pinmux.0x0221266c = 0x00000000; # CONTROL M3
pinmux.0x02212670 = 0x00000000; # OUTPUT M3
pinmux.0x02440048 = 0x00000000; # GPIO dp_aux_ch3_hpd_pm3
pinmux.0x022126c0 = 0x00000003; # CONFIG M6
pinmux.0x022126cc = 0x00000000; # CONTROL M6
pinmux.0x022126d0 = 0x00000000; # OUTPUT M6
pinmux.0x02440008 = 0x00000000; # GPIO soc_gpio51_pm6
pinmux.0x02212800 = 0x00000003; # CONFIG N0
pinmux.0x0221280c = 0x00000000; # CONTROL N0
pinmux.0x02212810 = 0x00000000; # OUTPUT N0
pinmux.0x02440018 = 0x00000000; # GPIO soc_gpio53_pn0
#### Pinmux for gpio-output-high pins ####
pinmux.0x0c2f1680 = 0x00000003; # CONFIG AA4
pinmux.0x0c2f168c = 0x00000000; # CONTROL AA4
pinmux.0x0c2f1690 = 0x00000001; # OUTPUT AA4
pinmux.0x0c303020 = 0x00000000; # GPIO can0_stb_paa4
pinmux.0x02212aa0 = 0x00000003; # CONFIG P5
pinmux.0x02212aac = 0x00000000; # CONTROL P5
pinmux.0x02212ab0 = 0x00000001; # OUTPUT P5
pinmux.0x02430078 = 0x00000000; # GPIO soc_gpio05_pp5
pinmux.0x02211400 = 0x00000003; # CONFIG A0
pinmux.0x0221140c = 0x00000000; # CONTROL A0
pinmux.0x02211410 = 0x00000001; # OUTPUT A0
pinmux.0x02432018 = 0x00000000; # GPIO dap6_sclk_pa0
pinmux.0x02211460 = 0x00000003; # CONFIG A3
pinmux.0x0221146c = 0x00000000; # CONTROL A3
pinmux.0x02211470 = 0x00000001; # OUTPUT A3
pinmux.0x02432000 = 0x00000000; # GPIO dap6_fs_pa3
pinmux.0x022126a0 = 0x00000003; # CONFIG M5
pinmux.0x022126ac = 0x00000000; # CONTROL M5
pinmux.0x022126b0 = 0x00000001; # OUTPUT M5
pinmux.0x02440000 = 0x00000000; # GPIO soc_gpio50_pm5
pinmux.0x022126e0 = 0x00000003; # CONFIG M7
pinmux.0x022126ec = 0x00000000; # CONTROL M7
pinmux.0x022126f0 = 0x00000001; # OUTPUT M7
pinmux.0x02440010 = 0x00000000; # GPIO soc_gpio52_pm7

#### Pinmux for used pins ####
pinmux.0x02431040 = 0x00000400; # dap1_sclk_ps0: i2s1, tristate-disable, input-disable, lpdr-disable
pinmux.0x02431038 = 0x00000400; # dap1_dout_ps1: i2s1, tristate-disable, input-disable, lpdr-disable
pinmux.0x02431030 = 0x00000454; # dap1_din_ps2: i2s1, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x02431028 = 0x00000400; # dap1_fs_ps3: i2s1, tristate-disable, input-disable, lpdr-disable
pinmux.0x02431020 = 0x00000400; # aud_mclk_ps4: aud, tristate-disable, input-disable, lpdr-disable
pinmux.0x02431010 = 0x00000459; # soc_gpio31_ps6: sdmmc1, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02438000 = 0x0000a460; # sdmmc1_clk_pj0: sdmmc1, tristate-disable, input-enable, loopback-enable
pinmux.0x02438008 = 0x0000a448; # sdmmc1_cmd_pj1: sdmmc1, pull-up, tristate-disable, input-enable
pinmux.0x02438030 = 0x0000a448; # sdmmc1_dat0_pj2: sdmmc1, pull-up, tristate-disable, input-enable
pinmux.0x02438028 = 0x0000a448; # sdmmc1_dat1_pj3: sdmmc1, pull-up, tristate-disable, input-enable
pinmux.0x02438020 = 0x0000a448; # sdmmc1_dat2_pj4: sdmmc1, pull-up, tristate-disable, input-enable
pinmux.0x02438018 = 0x0000a448; # sdmmc1_dat3_pj5: sdmmc1, pull-up, tristate-disable, input-enable
pinmux.0x02445058 = 0x00022400; # eqos_txc_pe0: eqos, tristate-disable, input-disable
pinmux.0x02445018 = 0x00022400; # eqos_td0_pe1: eqos, tristate-disable, input-disable
pinmux.0x02445010 = 0x00022400; # eqos_td1_pe2: eqos, tristate-disable, input-disable
pinmux.0x02445008 = 0x00022400; # eqos_td2_pe3: eqos, tristate-disable, input-disable
pinmux.0x02445000 = 0x00022400; # eqos_td3_pe4: eqos, tristate-disable, input-disable
pinmux.0x02445068 = 0x00022400; # eqos_tx_ctl_pe5: eqos, tristate-disable, input-disable
pinmux.0x02445040 = 0x00022450; # eqos_rd0_pe6: eqos, tristate-enable, input-enable
pinmux.0x02445030 = 0x00022450; # eqos_rd1_pe7: eqos, tristate-enable, input-enable
pinmux.0x02445028 = 0x00022450; # eqos_rd2_pf0: eqos, tristate-enable, input-enable
pinmux.0x02445020 = 0x00022470; # eqos_rd3_pf1: eqos, tristate-enable, input-enable
pinmux.0x02445070 = 0x00022450; # eqos_rx_ctl_pf2: eqos, tristate-enable, input-enable
pinmux.0x02445060 = 0x00022450; # eqos_rxc_pf3: eqos, tristate-enable, input-enable
pinmux.0x02445038 = 0x00022440; # eqos_sma_mdio_pf4: eqos, tristate-disable, input-enable
pinmux.0x02445048 = 0x00022400; # eqos_sma_mdc_pf5: eqos, tristate-disable, input-disable
pinmux.0x0243b020 = 0x00023460; # qspi0_sck_pc0: qspi0, tristate-disable, input-enable, loopback-enable
pinmux.0x0243b028 = 0x00023400; # qspi0_cs_n_pc1: qspi0, tristate-disable, input-disable
pinmux.0x0243b018 = 0x00023440; # qspi0_io0_pc2: qspi0, tristate-disable, input-enable
pinmux.0x0243b010 = 0x00023440; # qspi0_io1_pc3: qspi0, tristate-disable, input-enable
pinmux.0x0243b008 = 0x00023440; # qspi0_io2_pc4: qspi0, tristate-disable, input-enable
pinmux.0x0243b000 = 0x00023440; # qspi0_io3_pc5: qspi0, tristate-disable, input-enable
pinmux.0x0243b050 = 0x00023460; # qspi1_sck_pc6: qspi1, tristate-disable, input-enable, loopback-enable
pinmux.0x0243b058 = 0x00023400; # qspi1_cs_n_pc7: qspi1, tristate-disable, input-disable
pinmux.0x0243b048 = 0x00023440; # qspi1_io0_pd0: qspi1, tristate-disable, input-enable
pinmux.0x0243b040 = 0x00023440; # qspi1_io1_pd1: qspi1, tristate-disable, input-enable
pinmux.0x0243b038 = 0x00023440; # qspi1_io2_pd2: qspi1, tristate-disable, input-enable
pinmux.0x0243b030 = 0x00023440; # qspi1_io3_pd3: qspi1, tristate-disable, input-enable
pinmux.0x02436008 = 0x00002460; # sdmmc4_clk: sdmmc4, tristate-disable, input-enable, loopback-enable
pinmux.0x02436010 = 0x00002440; # sdmmc4_cmd: sdmmc4, tristate-disable, input-enable
pinmux.0x02436058 = 0x00002448; # sdmmc4_dat0: sdmmc4, pull-up, tristate-disable, input-enable
pinmux.0x02436050 = 0x00002448; # sdmmc4_dat1: sdmmc4, pull-up, tristate-disable, input-enable
pinmux.0x02436048 = 0x00002448; # sdmmc4_dat2: sdmmc4, pull-up, tristate-disable, input-enable
pinmux.0x02436040 = 0x00002448; # sdmmc4_dat3: sdmmc4, pull-up, tristate-disable, input-enable
pinmux.0x02436038 = 0x00002448; # sdmmc4_dat4: sdmmc4, pull-up, tristate-disable, input-enable
pinmux.0x02436030 = 0x00002448; # sdmmc4_dat5: sdmmc4, pull-up, tristate-disable, input-enable
pinmux.0x02436028 = 0x00002448; # sdmmc4_dat6: sdmmc4, pull-up, tristate-disable, input-enable
pinmux.0x02436020 = 0x00002448; # sdmmc4_dat7: sdmmc4, pull-up, tristate-disable, input-enable
pinmux.0x02436018 = 0x00000450; # sdmmc4_dqs: sdmmc4, tristate-enable, input-enable
pinmux.0x02434080 = 0x00000410; # soc_gpio10_pg6: gp, tristate-enable, input-disable, lpdr-disable
pinmux.0x02434098 = 0x00000411; # soc_gpio13_ph1: gp, tristate-enable, input-disable, lpdr-disable
pinmux.0x02434060 = 0x00000440; # gen1_i2c_scl_pi3: i2c1, tristate-disable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x02434068 = 0x00000440; # gen1_i2c_sda_pi4: i2c1, tristate-disable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x0243d038 = 0x00000410; # gp_pwm2_px2: gp, tristate-enable, input-disable, lpdr-disable
pinmux.0x0243d030 = 0x00000410; # gp_pwm3_px3: gp, tristate-enable, input-disable, lpdr-disable
pinmux.0x0243d070 = 0x00000400; # uart2_tx_px4: uartb, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0243d078 = 0x00000458; # uart2_rx_px5: uartb, pull-up, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x0243d080 = 0x00000400; # uart2_rts_px6: uartb, tristate-disable, input-disable, lpdr-disable
pinmux.0x0243d088 = 0x00000458; # uart2_cts_px7: uartb, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x0243d098 = 0x00000400; # uart5_tx_py5: uarte, tristate-disable, input-disable, lpdr-disable
pinmux.0x0243d090 = 0x00000458; # uart5_rx_py6: uarte, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x0243d0a0 = 0x00000400; # uart5_rts_py7: uarte, tristate-disable, input-disable, lpdr-disable
pinmux.0x0243d0a8 = 0x00000458; # uart5_cts_pz0: uarte, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x0c301000 = 0x00000500; # shutdown_n: shutdown, tristate-disable, input-disable, io_high_voltage-disable, lpdr-enable
pinmux.0x0c301040 = 0x00000440; # pwr_i2c_scl_pee5: i2c5, tristate-disable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c301048 = 0x00000440; # pwr_i2c_sda_pee6: i2c5, tristate-disable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c301028 = 0x00000458; # batt_oc_pee3: soc, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x0c302048 = 0x00000400; # spi2_sck_pcc0: spi2, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c302050 = 0x00000450; # spi2_miso_pcc1: spi2, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c302028 = 0x00000400; # spi2_mosi_pcc2: spi2, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c302038 = 0x00000400; # spi2_cs0_pcc3: spi2, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c302000 = 0x00000400; # touch_clk_pcc4: gp, tristate-disable, input-disable, lpdr-disable
pinmux.0x0c302010 = 0x00000400; # uart3_tx_pcc5: uartc, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c302008 = 0x00000458; # uart3_rx_pcc6: uartc, pull-up, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c302030 = 0x00000540; # gen2_i2c_scl_pcc7: i2c2, tristate-disable, input-enable, io_high_voltage-disable, lpdr-enable
pinmux.0x0c302040 = 0x00000540; # gen2_i2c_sda_pdd0: i2c2, tristate-disable, input-enable, io_high_voltage-disable, lpdr-enable
pinmux.0x0c302020 = 0x00000540; # gen8_i2c_scl_pdd1: i2c8, tristate-disable, input-enable, io_high_voltage-disable, lpdr-enable
pinmux.0x0c302018 = 0x00000540; # gen8_i2c_sda_pdd2: i2c8, tristate-disable, input-enable, io_high_voltage-disable, lpdr-enable
pinmux.0x02430008 = 0x00000400; # extperiph1_clk_pp0: extperiph1, tristate-disable, input-disable, lpdr-disable
pinmux.0x02430000 = 0x00000400; # extperiph2_clk_pp1: extperiph2, tristate-disable, input-disable, lpdr-disable
pinmux.0x02430018 = 0x00000440; # cam_i2c_scl_pp2: i2c3, tristate-disable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x02430010 = 0x00000440; # cam_i2c_sda_pp3: i2c3, tristate-disable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x02430088 = 0x0000045a; # soc_gpio07_pp7: soc, pull-up, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x02430060 = 0x00000459; # soc_gpio22_pq2: nv, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02430028 = 0x00000401; # soc_gpio41_pq5: extperiph3, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x024300a8 = 0x00000400; # uart1_tx_pr2: uarta, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x024300a0 = 0x00000458; # uart1_rx_pr3: uarta, pull-up, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x02432038 = 0x0000c400; # dap4_sclk_pa4: i2s4, tristate-disable, input-disable
pinmux.0x02432030 = 0x0000c400; # dap4_dout_pa5: i2s4, tristate-disable, input-disable
pinmux.0x02432028 = 0x0000c454; # dap4_din_pa6: i2s4, pull-down, tristate-enable, input-enable
pinmux.0x02432020 = 0x0000c400; # dap4_fs_pa7: i2s4, tristate-disable, input-disable
pinmux.0x02441008 = 0x00022420; # ufs0_ref_clk_pff0: ufs0, tristate-disable, input-disable
pinmux.0x02441000 = 0x00022420; # ufs0_rst_pff1: ufs0, tristate-disable, input-disable
pinmux.0x02437020 = 0x00000560; # pex_l0_clkreq_n_pk0: pe0, tristate-disable, input-enable, io_high_voltage-enable, lpdr-enable
pinmux.0x02437028 = 0x00000520; # pex_l0_rst_n_pk1: pe0, tristate-disable, input-disable, io_high_voltage-enable, lpdr-enable
pinmux.0x02437010 = 0x00000560; # pex_l1_clkreq_n_pk2: pe1, tristate-disable, input-enable, io_high_voltage-enable, lpdr-enable
pinmux.0x02437018 = 0x00000520; # pex_l1_rst_n_pk3: pe1, tristate-disable, input-disable, io_high_voltage-enable, lpdr-enable
pinmux.0x02437000 = 0x00000560; # pex_l2_clkreq_n_pk4: pe2, tristate-disable, input-enable, io_high_voltage-enable, lpdr-enable
pinmux.0x02437030 = 0x00000520; # pex_l2_rst_n_pk5: pe2, tristate-disable, input-disable, io_high_voltage-enable, lpdr-enable
pinmux.0x02437038 = 0x00000560; # pex_l3_clkreq_n_pk6: pe3, tristate-disable, input-enable, io_high_voltage-enable, lpdr-enable
pinmux.0x02437040 = 0x00000520; # pex_l3_rst_n_pk7: pe3, tristate-disable, input-disable, io_high_voltage-enable, lpdr-enable
pinmux.0x02437048 = 0x00000560; # pex_l4_clkreq_n_pl0: pe4, tristate-disable, input-enable, io_high_voltage-enable, lpdr-enable
pinmux.0x02437050 = 0x00000520; # pex_l4_rst_n_pl1: pe4, tristate-disable, input-disable, io_high_voltage-enable, lpdr-enable
pinmux.0x02440030 = 0x00000450; # dp_aux_ch0_hpd_pm0: dp, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x02440038 = 0x00000450; # dp_aux_ch1_hpd_pm1: dp, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x02440040 = 0x00000450; # dp_aux_ch2_hpd_pm2: dp, tristate-enable, input-enable, io_high_voltage-disable
pinmux.0x02440050 = 0x00000460; # hdmi_cec_pm4: hdmi, tristate-disable, input-enable, io_high_voltage-enable, lpdr-disable
pinmux.0x02431018 = 0x00000058; # soc_gpio30_ps5: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02431008 = 0x00000058; # soc_gpio32_ps7: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02431000 = 0x00000058; # soc_gpio33_pt0: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02431050 = 0x0000005a; # dap3_din_pt3: rsvd2, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02431048 = 0x00000002; # dap3_fs_pt4: rsvd2, tristate-disable, input-disable, lpdr-disable
pinmux.0x02431080 = 0x00000002; # dap5_sclk_pt5: rsvd2, tristate-disable, input-disable, lpdr-disable
pinmux.0x02431078 = 0x00000002; # dap5_dout_pt6: rsvd2, tristate-disable, input-disable, lpdr-disable
pinmux.0x02434058 = 0x00000058; # soc_gpio00_pg0: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02434050 = 0x00000058; # soc_gpio01_pg1: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02434048 = 0x00000058; # soc_gpio02_pg2: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02434040 = 0x00000058; # soc_gpio03_pg3: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02434070 = 0x00000058; # soc_gpio08_pg4: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02434078 = 0x00000000; # soc_gpio09_pg5: rsvd0, tristate-disable, input-disable, lpdr-disable
pinmux.0x02434088 = 0x00000050; # soc_gpio11_pg7: rsvd0, tristate-enable, input-enable, lpdr-disable
pinmux.0x02434090 = 0x00000054; # soc_gpio12_ph0: rsvd0, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x024340a0 = 0x00000050; # soc_gpio14_ph2: rsvd0, tristate-enable, input-enable, lpdr-disable
pinmux.0x02434038 = 0x00000409; # uart4_tx_ph3: rsvd1, pull-up, tristate-disable, input-disable, lpdr-disable
pinmux.0x02434020 = 0x00000405; # uart4_cts_ph6: rsvd1, pull-down, tristate-disable, input-disable, lpdr-disable
pinmux.0x02434018 = 0x00000055; # dap2_sclk_ph7: rsvd1, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x02434008 = 0x00000055; # dap2_dout_pi0: rsvd1, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x02434000 = 0x00000055; # dap2_din_pi1: rsvd1, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x02434010 = 0x00000055; # dap2_fs_pi2: rsvd1, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x0243d000 = 0x00000000; # gpu_pwr_req_px0: rsvd0, tristate-disable, input-disable, lpdr-disable
pinmux.0x0243d068 = 0x00000000; # cv_pwr_req_px1: rsvd0, tristate-disable, input-disable, lpdr-disable
pinmux.0x0243d008 = 0x00000001; # spi3_miso_py1: rsvd1, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0243d060 = 0x00000411; # spi3_mosi_py2: rsvd1, tristate-enable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0243d028 = 0x00000001; # spi3_cs1_py4: rsvd1, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0243d0b0 = 0x00000059; # usb_vbus_en0_pz1: rsvd1, pull-up, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x0243d0b8 = 0x00000001; # usb_vbus_en1_pz2: rsvd1, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0243d040 = 0x00000055; # spi1_sck_pz3: rsvd1, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x0243d020 = 0x00000055; # spi1_miso_pz4: rsvd1, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x0243d058 = 0x00000055; # spi1_mosi_pz5: rsvd1, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x0243d010 = 0x00000059; # spi1_cs0_pz6: rsvd1, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x0243d050 = 0x00000059; # spi1_cs1_pz7: rsvd1, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x0c301010 = 0x00000059; # safe_state_pee0: rsvd1, pull-up, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c301038 = 0x00000058; # power_on_pee4: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x0c303000 = 0x0000c055; # can1_dout_paa0: rsvd1, pull-down, tristate-enable, input-enable
pinmux.0x0c303008 = 0x0000c055; # can1_din_paa1: rsvd1, pull-down, tristate-enable, input-enable
pinmux.0x0c303010 = 0x0000c059; # can0_dout_paa2: rsvd1, pull-up, tristate-enable, input-enable
pinmux.0x0c303018 = 0x0000c059; # can0_din_paa3: rsvd1, pull-up, tristate-enable, input-enable
pinmux.0x0c303020 = 0x0000c000; # can0_stb_paa4: rsvd0, tristate-disable, input-disable
pinmux.0x0c303028 = 0x0000c000; # can0_en_paa5: rsvd0, tristate-disable, input-disable
pinmux.0x0c303030 = 0x0000c000; # can0_wake_paa6: rsvd0, tristate-disable, input-disable
pinmux.0x0c303038 = 0x0000c048; # can0_err_paa7: rsvd0, pull-up, tristate-disable, input-enable
pinmux.0x0c303040 = 0x0000c000; # can1_stb_pbb0: rsvd0, tristate-disable, input-disable
pinmux.0x0c303048 = 0x0000c000; # can1_en_pbb1: rsvd0, tristate-disable, input-disable
pinmux.0x0c303050 = 0x0000c000; # can1_wake_pbb2: rsvd0, tristate-disable, input-disable
pinmux.0x02430078 = 0x00000000; # soc_gpio05_pp5: rsvd0, tristate-disable, input-disable, lpdr-disable
pinmux.0x02430080 = 0x00000058; # soc_gpio06_pp6: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02430050 = 0x00000058; # soc_gpio20_pq0: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
pinmux.0x02430058 = 0x00000054; # soc_gpio21_pq1: rsvd0, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x02430020 = 0x00000002; # soc_gpio40_pq4: rsvd2, tristate-disable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x02430030 = 0x0000005a; # soc_gpio42_pq6: rsvd2, pull-up, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x02430038 = 0x00000022; # soc_gpio43_pq7: rsvd2, tristate-disable, input-disable, io_high_voltage-enable, lpdr-disable
pinmux.0x02430040 = 0x00000056; # soc_gpio44_pr0: rsvd2, pull-down, tristate-enable, input-enable, io_high_voltage-disable, lpdr-disable
pinmux.0x02430098 = 0x00000055; # uart1_rts_pr4: rsvd1, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x02430090 = 0x00000055; # uart1_cts_pr5: rsvd1, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x02432018 = 0x0000c002; # dap6_sclk_pa0: rsvd2, tristate-disable, input-disable
pinmux.0x02432010 = 0x0000c002; # dap6_dout_pa1: rsvd2, tristate-disable, input-disable
pinmux.0x02432008 = 0x0000c05a; # dap6_din_pa2: rsvd2, pull-up, tristate-enable, input-enable
pinmux.0x02432000 = 0x0000c002; # dap6_fs_pa3: rsvd2, tristate-disable, input-disable
pinmux.0x02446008 = 0x00000000; # cpu_pwr_req_0_pb0: rsvd0, tristate-disable, input-disable, lpdr-disable
pinmux.0x02446000 = 0x00000000; # cpu_pwr_req_1_pb1: rsvd0, tristate-disable, input-disable, lpdr-disable
pinmux.0x02437008 = 0x00000170; # pex_wake_n_pl2: rsvd0, tristate-enable, input-enable, io_high_voltage-enable, lpdr-enable
pinmux.0x02440048 = 0x00000002; # dp_aux_ch3_hpd_pm3: rsvd2, tristate-disable, input-disable, io_high_voltage-disable
pinmux.0x02440000 = 0x00000000; # soc_gpio50_pm5: rsvd0, tristate-disable, input-disable, lpdr-disable
pinmux.0x02440008 = 0x00000000; # soc_gpio51_pm6: rsvd0, tristate-disable, input-disable, lpdr-disable
pinmux.0x02440010 = 0x00000000; # soc_gpio52_pm7: rsvd0, tristate-disable, input-disable, lpdr-disable
pinmux.0x02440018 = 0x00000000; # soc_gpio53_pn0: rsvd0, tristate-disable, input-disable, lpdr-disable
pinmux.0x02440020 = 0x00000054; # soc_gpio54_pn1: rsvd0, pull-down, tristate-enable, input-enable, lpdr-disable
pinmux.0x02440028 = 0x00000058; # soc_gpio55_pn2: rsvd0, pull-up, tristate-enable, input-enable, lpdr-disable
#### Pinmux for unused pins for low-power configuration ####
pinmux.0x02431060 = 0x00000416; # dap3_sclk_pt1: rsvd2, pull-down, tristate-enable, input-disable, lpdr-disable
pinmux.0x02431058 = 0x00000416; # dap3_dout_pt2: rsvd2, pull-down, tristate-enable, input-disable, lpdr-disable
pinmux.0x02431070 = 0x00000417; # dap5_din_pt7: rsvd3, pull-down, tristate-enable, input-disable, lpdr-disable
pinmux.0x02431068 = 0x00000417; # dap5_fs_pu0: rsvd3, pull-down, tristate-enable, input-disable, lpdr-disable
pinmux.0x0243a030 = 0x0000a415; # sdmmc3_clk_po0: rsvd1, pull-down, tristate-enable, input-disable, loopback-disable
pinmux.0x0243a028 = 0x0000a415; # sdmmc3_cmd_po1: rsvd1, pull-down, tristate-enable, input-disable
pinmux.0x0243a018 = 0x0000a415; # sdmmc3_dat0_po2: rsvd1, pull-down, tristate-enable, input-disable
pinmux.0x0243a010 = 0x0000a415; # sdmmc3_dat1_po3: rsvd1, pull-down, tristate-enable, input-disable
pinmux.0x0243a008 = 0x0000a415; # sdmmc3_dat2_po4: rsvd1, pull-down, tristate-enable, input-disable
pinmux.0x0243a000 = 0x0000a415; # sdmmc3_dat3_po5: rsvd1, pull-down, tristate-enable, input-disable
pinmux.0x02434030 = 0x00000415; # uart4_rx_ph4: rsvd1, pull-down, tristate-enable, input-disable, lpdr-disable
pinmux.0x02434028 = 0x00000415; # uart4_rts_ph5: rsvd1, pull-down, tristate-enable, input-disable, lpdr-disable
pinmux.0x0243d048 = 0x00000415; # spi3_sck_py0: rsvd1, pull-down, tristate-enable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0243d018 = 0x00000415; # spi3_cs0_py3: rsvd1, pull-down, tristate-enable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c301018 = 0x00000415; # vcomp_alert_pee1: rsvd1, pull-down, tristate-enable, input-disable, lpdr-disable
pinmux.0x0c301060 = 0x00000415; # ao_retention_n_pee2: rsvd1, pull-down, tristate-enable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x0c303058 = 0x0000c414; # can1_err_pbb3: rsvd0, pull-down, tristate-enable, input-disable
pinmux.0x02430070 = 0x00000414; # soc_gpio04_pp4: rsvd0, pull-down, tristate-enable, input-disable, lpdr-disable
pinmux.0x02430068 = 0x00000414; # soc_gpio23_pq3: rsvd0, pull-down, tristate-enable, input-disable, lpdr-disable
pinmux.0x02430048 = 0x00000415; # soc_gpio45_pr1: rsvd1, pull-down, tristate-enable, input-disable, io_high_voltage-disable, lpdr-disable
pinmux.0x02437058 = 0x00000415; # sata_dev_slp_pl3: rsvd1, pull-down, tristate-enable, input-disable, io_high_voltage-disable, lpdr-disable
6

I set pull-up on this pin.It can output high,now.