# How much current can be drawn from pin2/4 of 40 pin header

**URL:** <https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703>\
**Category:** Jetson Xavier NX\
**Tags:** board-design\
**Created:** [June 30, 2020, 9:48am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703 "2020-06-30T09:48:18Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![KGH](https://developer.download.nvidia.com/images/forums/profile-default-devtalk-84.png) [@KGH](https://forums.developer.nvidia.com/u/KGH)\
**Post date:** [June 30, 2020, 9:48am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/1 "2020-06-30T09:48:18Z")

</div>

Hello,

To make a custom board on 40pin header, I tested drawing  
20 mA from pin 2/4 of J12, 40 pin header. I connected 220 ohm  
between pin 2/4 and 6 and measured the voltage between  
those two pins. It was around 2 V, not 5 V. How can I use  
5V pins of J12 correctly?

Thanks in advance for any suggestions.

---

<div class="post-metadata">

**Author:** ![Trumany](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/trumany/32/14043_2.png) [@Trumany](https://forums.developer.nvidia.com/u/Trumany)\
**Post date:** [July 1, 2020, 3:43am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/3 "2020-07-01T03:43:56Z")

</div>

Please read this doc first: [https://developer.nvidia.com/jetson-nano-developer-kit-40-pin-expansion-header-gpio-usage-considerations-applications-note](https://developer.nvidia.com/jetson-nano-developer-kit-40-pin-expansion-header-gpio-usage-considerations-applications-note)

There are some requests on the drive strength of pins as level shift exists.

---

<div class="post-metadata">

**Author:** ![KGH](https://developer.download.nvidia.com/images/forums/profile-default-devtalk-84.png) [@KGH](https://forums.developer.nvidia.com/u/KGH)\
**Post date:** [July 1, 2020, 7:29am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/4 "2020-07-01T07:29:46Z")

</div>

Thank you for reply.

I mentioned about power pins, not signal pins. I have both Nano  
and Xavier NX. Nano 5V power pin (2/4 pin) can be drawn more  
than 20 mA, but 5V power pins of NX cannot supply enough current.  
3.3V power pins of NX are OK.

---

<div class="post-metadata">

**Author:** ![Trumany](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/trumany/32/14043_2.png) [@Trumany](https://forums.developer.nvidia.com/u/Trumany)\
**Post date:** [July 1, 2020, 8:00am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/5 "2020-07-01T08:00:39Z")

</div>

The 5V power of it can be up to 1A supply. How many boards do you have and test? There is a “reverse current block” design as you can see in the schematic, you can measure the vdd\_5v\_sys to and vdd\_5v\_gpio on Q23 to make sure which one fails. The schematic and pcb file are here: [https://developer.nvidia.com/jetson-xavier-nx-developer-kit-carrier-board-design-package-p3509-a01](https://developer.nvidia.com/jetson-xavier-nx-developer-kit-carrier-board-design-package-p3509-a01)

---

<div class="post-metadata">

**Author:** ![KGH](https://developer.download.nvidia.com/images/forums/profile-default-devtalk-84.png) [@KGH](https://forums.developer.nvidia.com/u/KGH)\
**Post date:** [July 2, 2020, 7:00am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/6 "2020-07-02T07:00:16Z")

</div>

I tested Q23. When 200 ohm is connected between pin 4 (5 V pwr) and pin 6 (GND), Q23 drain is 5.11 V, source is 1.99 V and gate is 0.00 V.  
Is this data enough?

---

<div class="post-metadata">

**Author:** ![Trumany](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/trumany/32/14043_2.png) [@Trumany](https://forums.developer.nvidia.com/u/Trumany)\
**Post date:** [July 2, 2020, 10:30am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/7 "2020-07-02T10:30:11Z")

</div>

How many board did you test? Also can you try other pull-down too, such as 4.7k, 50k or others?

---

<div class="post-metadata">

**Author:** ![KGH](https://developer.download.nvidia.com/images/forums/profile-default-devtalk-84.png) [@KGH](https://forums.developer.nvidia.com/u/KGH)\
**Post date:** [July 2, 2020, 11:08am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/8 "2020-07-02T11:08:19Z")

</div>

I only have one NX.  
Now I test 1 kohm, source and pin 4 are both is 3.84 V.  
When 47 kohm, source and pin 4 are both 5.07 V.

This means, the internal resistance of power supply is around 300 ohm?

---

<div class="post-metadata">

**Author:** ![Trumany](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/trumany/32/14043_2.png) [@Trumany](https://forums.developer.nvidia.com/u/Trumany)\
**Post date:** [July 3, 2020, 6:04am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/9 "2020-07-03T06:04:05Z")

</div>

The Drain side is always 5V, right? If so, it is not power supply problem.

---

<div class="post-metadata">

**Author:** ![KGH](https://developer.download.nvidia.com/images/forums/profile-default-devtalk-84.png) [@KGH](https://forums.developer.nvidia.com/u/KGH)\
**Post date:** [July 6, 2020, 1:37am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/10 "2020-07-06T01:37:39Z")

</div>

Yes, drain is always 5.11 V. The MOSFET looks like a resister.

---

<div class="post-metadata">

**Author:** ![Trumany](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/trumany/32/14043_2.png) [@Trumany](https://forums.developer.nvidia.com/u/Trumany)\
**Post date:** [July 6, 2020, 2:03am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/11 "2020-07-06T02:03:03Z")

</div>

To check status of mosfet, can you try removing Q24 and using 1k pull-down instead of 47k(R180)?

---

<div class="post-metadata">

**Author:** ![Trumany](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/trumany/32/14043_2.png) [@Trumany](https://forums.developer.nvidia.com/u/Trumany)\
**Post date:** [July 6, 2020, 3:27am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/12 "2020-07-06T03:27:26Z")

</div>

Also could you send a picture of the rework so as to check how 220ohm was soldered? As it is very strange. Q23 is a P-FET so if its gate is at 0V and drain is 5.11V, then source should be also at 5.11V and not 1.99V.

---

<div class="post-metadata">

**Author:** ![KGH](https://developer.download.nvidia.com/images/forums/profile-default-devtalk-84.png) [@KGH](https://forums.developer.nvidia.com/u/KGH)\
**Post date:** [July 6, 2020, 9:54am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/13 "2020-07-06T09:54:59Z")

</div>

I can’t rework Q23. Q24 because it is too close to the connector J12.  
I don’t solder 220 ohm, only connect a resister between pin 2 and pin 6 of J12 using jump wires.

---

<div class="post-metadata">

**Author:** ![Trumany](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/trumany/32/14043_2.png) [@Trumany](https://forums.developer.nvidia.com/u/Trumany)\
**Post date:** [July 6, 2020, 1:01pm UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/14 "2020-07-06T13:01:53Z")

</div>

Can you share a picture of your setting of resistor?

---

<div class="post-metadata">

**Author:** ![KGH](https://developer.download.nvidia.com/images/forums/profile-default-devtalk-84.png) [@KGH](https://forums.developer.nvidia.com/u/KGH)\
**Post date:** [July 9, 2020, 4:21am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/15 "2020-07-09T04:21:58Z")

</div>

This picture is enough for you?

 ![Jetson_NX_NG0](https://global.discourse-cdn.com/nvidia/original/3X/c/2/c2c767f71a6d812f777bd183b66b6db1d4f69f24.jpeg)

---

<div class="post-metadata">

**Author:** ![Trumany](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/trumany/32/14043_2.png) [@Trumany](https://forums.developer.nvidia.com/u/Trumany)\
**Post date:** [July 9, 2020, 7:24am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/16 "2020-07-09T07:24:38Z")

</div>

Thanks, we are checking internally, will update once available.

---

<div class="post-metadata">

**Author:** ![KGH](https://developer.download.nvidia.com/images/forums/profile-default-devtalk-84.png) [@KGH](https://forums.developer.nvidia.com/u/KGH)\
**Post date:** [July 10, 2020, 2:30am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/17 "2020-07-10T02:30:42Z")

</div>

I borrow another Jetson Xavier NX from my colleague.  
It works fine. It can draw more than 100 mA from pin 2 of J12.  
It seems my board have some problem.

---

<div class="post-metadata">

**Author:** ![Trumany](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/trumany/32/14043_2.png) [@Trumany](https://forums.developer.nvidia.com/u/Trumany)\
**Post date:** [July 10, 2020, 3:10am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/18 "2020-07-10T03:10:17Z")

</div>

OK, it looks like the mosfet issue, you can try removing it to validate.

---

<div class="post-metadata">

**Author:** ![william.thompson](https://developer.download.nvidia.com/images/forums/profile-default-devtalk-84.png) [@william.thompson](https://forums.developer.nvidia.com/u/william.thompson)\
**Post date:** [January 13, 2021, 4:11pm UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/20 "2021-01-13T16:11:12Z")

</div>

Hello, Does the attached document regarding the 40pin header apply to the xavier nx dev kit carrier board as well (level shifting, ect.)  
thanks

---

<div class="post-metadata">

**Author:** ![Trumany](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/trumany/32/14043_2.png) [@Trumany](https://forums.developer.nvidia.com/u/Trumany)\
**Post date:** [January 14, 2021, 1:42am UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/21 "2021-01-14T01:42:33Z")

</div>

Yes, the 40-pin expansion header is same.

---

<div class="post-metadata">

**Author:** ![nadeemm](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/nadeemm/32/367020_2.png) [@nadeemm](https://forums.developer.nvidia.com/u/nadeemm)\
**Post date:** [October 18, 2021, 6:42pm UTC](https://forums.developer.nvidia.com/t/how-much-current-can-be-drawn-from-pin2-4-of-40-pin-header/139703/22 "2021-10-18T18:42:22Z")

</div>

Closed on October 18, 2021, 6:42pm UTC


