HP DL 385P gen 8 prolidant and GPU Card (tesla K20, Quadro K5000)

Bonjour,

Nous possédons un serveur “HP DL385P gen8 proliant”.
Nous cherchons a ajouter une carte GPU pour CUDA.

Après des recherches auprès de HP et PNY, voici les réponses:

constructeur de la carte GPU “PNY”:

[i]Cher M. Schmitt,

Cet email fait suite à notre conversation de ce matin.

Dans la mesure où vous ne disposez que d’un adaptateur d’alimentation PCI-E 6-pin et que HP semble ne proposer que cette possibilité afin d’installer un GPU nécessitant plus qu’un simple slot PCI-E pour être alimenté, vous êtes limité aux cartes munies d’un seul connecteur PCI-E 6-pin et consommant 150 Watts maximum.
Ainsi en l’état, la carte Tesla K20c dont vous faisiez mention ne peut fonctionner dans ce serveur HP car elle est équipée de deux connecteurs PCI-E 6-pin qui doivent être alimentés.
La carte Quadro K5000 devrait être adaptée, ses spécifications techniques - notamment la partie alimentation -, correspondent aux capacités d’accueil du système.

Cordialement,[/i]

constructeur du serveur “HP”:

[i]Nous ne sommes pas en mesure de répondre officiellement à cette question car elle n’est pas dans le cadre du support technique avant-vente que nous pouvons fournir. A titre d’information, nous avons consulté un document interne sur les cartes graphiques supportées par les Proliant mais à ce jour, il n’y a aucune information à propos de test sur DL385p Gen8 et nous ne saurions pas dire que cette situation évoluera ou restera telle qu’elle dans le futur. Actuellement donc, installer le K5000 sur le DL385p Gen8 n’est pas une solution supportée par HP. Veuillez noter que non supportée ne veut pas forcément dire que la solution ne va pas fonctionner, le client peut la tenter mais ce sera entièrement sous sa responsabilité puisque nous ne pouvons pas garantir ni le résultat, ni la stabilité de cette configuration.

Cordialement,
[/i]

Qu’en pensez vous?

Hello,

We have a " HP proliant DL385P Gen8 server" .
We are looking to add a GPU for CUDA .

According to research from HP and PNY , here are the answers :


manufacturer of the GPU " PNY "

[i]Dear Mr. Schmitt,

This email is further to our conversation this morning .

Insofar as you have only one PCI -E 6-pin power adapter and HP seems to suggest that the possibility to install a GPU requires more than just PCI- E to be fed , you are limited to cards with one PCI -E 6-pin connector and consumes 150 Watts maximum .
And as such, the Tesla K20c card which you were referred can not function in this HP server because it is equipped with two 6-pin PCI -E connectors that must be supplied .
Quadro K5000 card should be adapted , technical specifications - including the power part - correspond to the homepage of the system capabilities.

Regards,[/i]


manufacturer “HP” server:

[i]We are not able to officially answer this question because it is not in the technical pre-sales support we can provide . For your information , we consulted an internal document on graphics cards supported by the ProLiant but to date , there is no information about test DL385p Gen8 and we would not know that this situation will change or remain as in the future. Currently , therefore , installed on the K5000 DL385p Gen8 is not supported by a HP solution . Please note that unsupported does not mean that the solution will not work , the customer can try but it will be entirely under his responsibility since we can not guarantee neither the result nor the stability of this configuration.

Regards,[/i]

What do you think ?