Here it is the serial console full log with initially flashing 32.5 L4T:
[0228.053] Enabled early print
[0228.056] [L4T TegraBoot] (version �����B����$�)X�j��:@����)
[0228.062] Processing in recovery mode
[0228.065] A02 Bootrom Patch rev = 1023
[0228.069] Power-up reason: software reset
[0228.073] Established communication link with host
[0229.059] Odmdata from BCT: 0x000a4000
[0229.063] DebugPort= 0x3
[0229.065] SkipQspiOnly= 0x0
[0229.117] BoardId read from EEPROM/NCT: 3448
[0229.122] BoardID = 3448, SKU = 0x0
[0229.149] NvTbootInit_Porg: Setting GPIO_A6 for HDMI ...
[0229.154] max77620 setting MBLPD bit
[0229.157] No Battery Present
[0229.160] RamCode = 0
[0229.162] Platform has DDR4 type RAM
[0229.166] max77620 disabling SD1 Remote Sense
[0229.170] Setting DDR voltage to 1125mv
[0229.174] Serial Number of Pmic Max77663: 0x221ff9
[0229.182] Entering ramdump check
[0229.185] Get RamDumpCarveOut = 0x0
[0229.188] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0229.193] Last reboot was clean, booting normally!
[0229.198] Sdram initialization is successful
[0229.202] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0229.208] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0229.214] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0229.220] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0229.226] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0229.232] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0229.238] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0229.243] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0229.260] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0229.266] Platform-DebugCarveout: 0
[0229.269] Downloaded BCT successfully
[0229.775] Downloaded Bootloader successfully
[0229.835] Downloaded rp1 successfully
[0229.865] MAX77620_GPIO5 configured
[0229.868] CPU power rail is up
[0229.871] CPU clock enabled
[0229.875] Performing RAM repair
[0229.878] Updating A64 Warmreset Address to 0x92c002e9
[0229.884] Enable APE clock/reset
[0229.887] Error in NvTbootGetTOSBinaryLength: 0x11 !
[0229.892] Loading Secure OS image failed.
[0229.896] Set NvDecSticky Bits
[0229.899] GSC2 address ff53fffc value c0edbbcc
[0229.906] GSC MC Settings done
[0229.910] Next binary entry address: 0x92c00258
[0229.914] BoardId: 3448
[0229.917] Overriding pmu board id with proc board id
[0229.922] Display board id is not available
[0229.926] Starting CPU & Halting co-processor
[0235.455]
[0235.456] Debug Init done
[0235.459] Marked DTB cacheable
[0235.462] Bootloader DTB loaded at 0x83000400
[0235.467] DeviceTree Init done
[0235.480] Pinmux applied successfully
[0235.484] gicd_base: 0x50041000
[0235.487] gicc_base: 0x50042000
[0235.490] Interrupts Init done
[0235.495] Using base:0x60005090 & irq:208 for tick-timer
[0235.500] Using base:0x60005098 for delay-timer
[0235.504] platform_init_timer: DONE
[0235.508] Timer(tick) Init done
[0235.511] osc freq = 38400 khz
[0235.515]
[0235.516] Welcome to L4T Cboot
[0235.519]
[0235.520] Cboot Version: 00.00.2018.01-t210-39562017
[0235.525] calling constructors
[0235.528] initializing heap
[0235.531] initializing threads
[0235.534] initializing timers
[0235.537] creating bootstrap completion thread
[0235.541] top of bootstrap2()
[0235.544] CPU: ARM Cortex A57
[0235.547] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0235.552] initializing platform
[0235.559] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0235.564] ID LSB = 0x36, ID-CFI len = 194 bytes
[0235.568] Macronix QSPI chip present
[0235.572] SPI device register
[0235.575] init boot device
[0235.577] allocating memory for boot device(SPI)
[0235.582] registering boot device
[0235.591] sdmmc node status = okay
[0235.595] sdcard instance = 0
[0235.597] sdcard gpio handle 0x5b
[0235.601] sdcard gpio pin 0xc9
[0235.604] sdcard gpio flags 0x0
[0235.607] vmmc-supply 0x9e
[0235.609] Instance: 0
[0235.611] Allocating memory for context
[0235.615] enabling clock
[0235.618] sd card init
[0235.620] Check card present and stable
[0235.624] Send command 0
[0235.724] Send command 3
[0235.729] Set RCA for the card
[0235.732] Query card specific data by command 9
[0235.738] Parse CSD data
[0235.740] Send command 7
[0235.751] Calling sd device register
[0235.754] Init sdcard
[0235.757] Allocating memory for boot device
[0235.761] Registering user device
[0235.774] of_register: registering tegra_udc to of_hal
[0235.779] of_register: registering inv20628-driver to of_hal
[0235.785] of_register: registering ads1015-driver to of_hal
[0235.790] of_register: registering lp8557-bl-driver to of_hal
[0235.796] of_register: registering bq2419x_charger to of_hal
[0235.801] of_register: registering bq27441_fuel_gauge to of_hal
[0235.813] gpio framework initialized
[0235.817] of_register: registering tca9539_gpio to of_hal
[0235.822] of_register: registering tca9539_gpio to of_hal
[0235.827] of_register: registering i2c_bus_driver to of_hal
[0235.833] of_register: registering i2c_bus_driver to of_hal
[0235.839] of_register: registering i2c_bus_driver to of_hal
[0235.844] pmic framework initialized
[0235.848] of_register: registering max77620_pmic to of_hal
[0235.853] regulator framework initialized
[0235.857] of_register: registering tps65132_bl_driver to of_hal
[0235.863] initializing target
[0235.869] gpio_driver_register: register 'tegra_gpio_driver' driver
[0235.877] board ID = D78, board SKU = 0
[0235.881] Skipping Z3!
[0235.886] fixed regulator driver initialized
[0235.904] initializing OF layer
[0235.908] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0235.926] I2C Bus Init done
[0235.928] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0235.938] I2C Bus Init done
[0235.941] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0235.951] I2C Bus Init done
[0235.954] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0235.965] I2C Bus Init done
[0235.967] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0235.978] I2C Bus Init done
[0235.980] of_children_init: Ops found for compatible string maxim,max77620
[0235.991] max77620_init using irq 118
[0235.996] register 'maxim,max77620' pmic
[0236.000] gpio_driver_register: register 'max77620-gpio' driver
[0236.006] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0236.017] I2C Bus Init done
[0236.020] Applying platform configs
[0236.027] platform-init is not present. Skipping
[0236.032] calling apps_init()
[0236.052] Found 14 GPT partitions in "sd0"
[0236.056] Proceeding to flashing Server
[0236.060] usbdcd_reinit Initialize driver to use already enumerated device
[0236.067] nv3p_priv_usbf_open USB configuration success
[0236.141] Writing GPT partition
[0236.146] Erasing Boot device
[0236.149] device_write_gpt: Erasing boot device spiflash0
[0253.798] Erasing Storage Device
[0253.801] Writing protective mbr
[0253.826] Writing primary GPT
[0254.198] Writing secondary GPT
[0254.234] Found 1 GPT partitions in "sd0"
[0296.347] Writing PT partition
[0296.597] partition PT write successful.
[0296.602] Writing NVC partition
[0306.625] partition NVC write successful.
[0306.631] Writing NVC_R partition
[0316.664] partition NVC_R write successful.
[0316.669] Writing TBC partition
[0320.843] partition TBC write successful.
[0320.850] Writing RP1 partition
[0335.523] partition RP1 write successful.
[0335.530] Writing EBT partition
[0364.611] partition EBT write successful.
[0364.619] Writing WB0 partition
[0364.887] partition WB0 write successful.
[0364.894] Writing BPF partition
[0365.162] partition BPF write successful.
[0365.169] Writing TOS partition
[0368.611] partition TOS write successful.
[0368.617] Writing DTB partition
[0383.290] partition DTB write successful.
[0383.296] Writing LNX partition
[0422.875] partition LNX write successful.
[0422.890] Writing EKS partition
[0423.157] partition EKS write successful.
[0423.163] Writing BMP partition
[0432.251] partition BMP write successful.
[0432.257] Writing RP4 partition
[0439.851] partition RP4 write successful.
[0439.857] Writing VER_b partition
[0440.146] partition VER_b write successful.
[0440.151] Writing VER partition
[0440.419] partition VER write successful.
[0440.424] Writing APP partition
[0962.135] partition APP write successful.
[0962.152] Writing BCT partition
[0968.803] partition BCT write successful.
[0968.813] Change state to cold boot mode
[0000.157] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.162] Processing in cold boot mode Bootloader 2
[0000.167] A02 Bootrom Patch rev = 1023
[0000.171] Power-up reason: software reset
[0000.174] No Battery Present
[0000.177] pmic max77620 reset reason
[0000.180] pmic max77620 NVERC : 0x0
[0000.184] RamCode = 0
[0000.186] Platform has DDR4 type RAM
[0000.189] max77620 disabling SD1 Remote Sense
[0000.193] Setting DDR voltage to 1125mv
[0000.197] Serial Number of Pmic Max77663: 0x221ff9
[0000.205] Entering ramdump check
[0000.208] Get RamDumpCarveOut = 0x0
[0000.211] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.217] Last reboot was clean, booting normally!
[0000.221] Sdram initialization is successful
[0000.225] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.231] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.237] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.243] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.249] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.255] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.261] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.266] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.283] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.289] Platform-DebugCarveout: 0
[0000.292] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.298] Non secure mode, and RB not enabled.
[0000.302] BoardID = 3448, SKU = 0x0
[0000.305] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.309] Nano-SD: checking PT table on QSPI ...
[0000.313] Read PT from (2:0)
[0000.329] Using BFS PT to query partitions
[0000.334] Loading Tboot-CPU binary
[0000.363] Verifying TBC in OdmNonSecureSBK mode
[0000.373] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.380] Bootloader downloaded successfully.
[0000.384] Downloaded Tboot-CPU binary to 0xa0000258
[0000.389] MAX77620_GPIO5 configured
[0000.392] CPU power rail is up
[0000.395] CPU clock enabled
[0000.399] Performing RAM repair
[0000.402] Updating A64 Warmreset Address to 0xa00002e9
[0000.407] BoardID = 3448, SKU = 0x0
[0000.410] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.414] Nano-SD: checking PT table on QSPI ...
[0000.418] Loading NvTbootBootloaderDTB
[0000.485] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.558] Bootloader DTB Load Address: 0x83000000
[0000.562] BoardID = 3448, SKU = 0x0
[0000.566] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.570] Nano-SD: checking PT table on QSPI ...
[0000.574] Loading NvTbootKernelDTB
[0000.640] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.713] Kernel DTB Load Address: 0x83100000
[0000.717] BoardID = 3448, SKU = 0x0
[0000.721] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.724] Nano-SD: checking PT table on QSPI ...
[0000.731] Loading cboot binary
[0000.846] Verifying EBT in OdmNonSecureSBK mode
[0000.888] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.895] Bootloader downloaded successfully.
[0000.899] BoardID = 3448, SKU = 0x0
[0000.902] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.906] Nano-SD: checking PT table on QSPI ...
[0000.911] PT: Partition NCT NOT found !
[0000.915] Warning: Find Partition via PT Failed
[0000.919] Next binary entry address: 0x92c00258
[0000.923] BoardId: 3448
[0000.928] Overriding pmu board id with proc board id
[0000.933] Display board id is not available
[0000.937] BoardID = 3448, SKU = 0x0
[0000.940] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.944] Nano-SD: checking PT table on QSPI ...
[0001.049] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.106] /bpmp deleted
[0001.108] SC7EntryFw header found loaded at 0xff700000
[0001.303] OVR2 PMIC
[0001.305] Bpmp FW successfully loaded
[0001.309] BoardID = 3448, SKU = 0x0
[0001.312] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.316] Nano-SD: checking PT table on QSPI ...
[0001.321] WB0 init successfully at 0xff780000
[0001.325] Set NvDecSticky Bits
[0001.329] GSC2 address ff53fffc value c0edbbcc
[0001.335] GSC MC Settings done
[0001.338] BoardID = 3448, SKU = 0x0
[0001.341] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.345] Nano-SD: checking PT table on QSPI ...
[0001.351] TOS Image length 53680
[0001.354] Monitor size 53680
[0001.356] OS size 0
[0001.372] Secure Os AES-CMAC Verification Success!
[0001.376] TOS image cipher info: plaintext
[0001.380] Loading and Validation of Secure OS Successful
[0001.396] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.401] NvTbootPackSdramParams: start.
[0001.406] NvTbootPackSdramParams: done.
[0001.410] Tegraboot started after 84893 us
[0001.414] Basic modules init took 887021 us
[0001.418] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB
[0001.423] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.429] Next stage binary read took 102860 us
[0001.433] Carveout took -126355 us
[0001.436] CPU initialization took 495395 us
[0001.440] Total time taken by TegraBoot 1358921 us
[0001.445] Starting CPU & Halting co-processor
64NOTICE: BL31: v1.3(release):5b49e7f80
NOTICE: BL31: Built : 14:33:23, Jan 15 2021
ERROR: Error initializing runtime service trusty_fast
[0001.567] RamCode = 0
[0001.572] LPDDR4 Training: Read DT: Number of tables = 2
[0001.577] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.590] EMC Training Successful
[0001.593] 408000 not found in DVFS table
[0001.599] RamCode = 0
[0001.603] DT Write: emc-table@204000 succeeded
[0001.608] DT Write: emc-table@1600000 succeeded
[0001.612] LPDDR4 Training: Write DT: Number of tables = 2
[0001.660]
[0001.661] Debug Init done
[0001.663] Marked DTB cacheable
[0001.666] Bootloader DTB loaded at 0x83000000
[0001.671] Marked DTB cacheable
[0001.674] Kernel DTB loaded at 0x83100000
[0001.678] DeviceTree Init done
[0001.691] Pinmux applied successfully
[0001.695] gicd_base: 0x50041000
[0001.699] gicc_base: 0x50042000
[0001.702] Interrupts Init done
[0001.706] Using base:0x60005090 & irq:208 for tick-timer
[0001.711] Using base:0x60005098 for delay-timer
[0001.716] platform_init_timer: DONE
[0001.719] Timer(tick) Init done
[0001.723] osc freq = 38400 khz
[0001.727]
[0001.728] Welcome to L4T Cboot
[0001.731]
[0001.732] Cboot Version: 00.00.2018.01-t210-39562017
[0001.737] calling constructors
[0001.740] initializing heap
[0001.742] initializing threads
[0001.745] initializing timers
[0001.748] creating bootstrap completion thread
[0001.753] top of bootstrap2()
[0001.756] CPU: ARM Cortex A57
[0001.758] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.763] initializing platform
[0001.771] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0001.775] ID LSB = 0x36, ID-CFI len = 194 bytes
[0001.780] Macronix QSPI chip present
[0001.783] SPI device register
[0001.786] init boot device
[0001.789] allocating memory for boot device(SPI)
[0001.793] registering boot device
[0001.802] QSPI bdev is already initialized
[0001.806] Enable APE clock
[0001.808] Un-powergate APE partition
[0001.812] of_register: registering tegra_udc to of_hal
[0001.817] of_register: registering inv20628-driver to of_hal
[0001.822] of_register: registering ads1015-driver to of_hal
[0001.828] of_register: registering lp8557-bl-driver to of_hal
[0001.834] of_register: registering bq2419x_charger to of_hal
[0001.839] of_register: registering bq27441_fuel_gauge to of_hal
[0001.851] gpio framework initialized
[0001.854] of_register: registering tca9539_gpio to of_hal
[0001.860] of_register: registering tca9539_gpio to of_hal
[0001.865] of_register: registering i2c_bus_driver to of_hal
[0001.871] of_register: registering i2c_bus_driver to of_hal
[0001.876] of_register: registering i2c_bus_driver to of_hal
[0001.882] pmic framework initialized
[0001.885] of_register: registering max77620_pmic to of_hal
[0001.891] regulator framework initialized
[0001.895] of_register: registering tps65132_bl_driver to of_hal
[0001.901] initializing target
[0001.906] gpio_driver_register: register 'tegra_gpio_driver' driver
[0001.915] board ID = D78, board SKU = 0
[0001.918] Skipping Z3!
[0001.923] fixed regulator driver initialized
[0001.941] initializing OF layer
[0001.944] NCK carveout not present
[0001.947] Skipping dts_overrides
[0001.951] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.968] I2C Bus Init done
[0001.971] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.981] I2C Bus Init done
[0001.984] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.994] I2C Bus Init done
[0001.997] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.007] I2C Bus Init done
[0002.010] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.020] I2C Bus Init done
[0002.023] of_children_init: Ops found for compatible string maxim,max77620
[0002.033] max77620_init using irq 118
[0002.038] register 'maxim,max77620' pmic
[0002.043] gpio_driver_register: register 'max77620-gpio' driver
[0002.049] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.059] I2C Bus Init done
[0002.063] NCK carveout not present
[0002.073] Find /i2c@7000c000's alias i2c0
[0002.077] get eeprom at 1-a0, size 256, type 0
[0002.086] Find /i2c@7000c500's alias i2c2
[0002.089] get eeprom at 3-a0, size 256, type 0
[0002.094] get eeprom at 3-ae, size 256, type 0
[0002.098] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.104] I2C slave not started
[0002.107] I2C write failed
[0002.109] Writing offset failed
[0002.112] eeprom_init: EEPROM read failed
[0002.116] pm_ids_update: eeprom init failed
[0002.120] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.150] pm_ids_update: The pm board id is 3448-0000-200
[0002.157] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.166] pm_ids_update: pm id update successful
[0002.170] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.200] pm_ids_update: The pm board id is 3449-0000-200
[0002.206] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.214] pm_ids_update: pm id update successful
[0002.245] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.251] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.258] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.264] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.273] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:1d:8e
[0002.279] Plugin Manager: Parse ODM data 0x000a4000
[0002.291] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0002.306] Find /i2c@7000c000's alias i2c0
[0002.310] get eeprom at 1-a0, size 256, type 0
[0002.319] Find /i2c@7000c500's alias i2c2
[0002.323] get eeprom at 3-a0, size 256, type 0
[0002.327] get eeprom at 3-ae, size 256, type 0
[0002.332] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.337] I2C slave not started
[0002.340] I2C write failed
[0002.343] Writing offset failed
[0002.346] eeprom_init: EEPROM read failed
[0002.350] pm_ids_update: eeprom init failed
[0002.354] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.384] pm_ids_update: The pm board id is 3448-0000-200
[0002.390] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.397] pm_ids_update: pm id update successful
[0002.402] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.432] pm_ids_update: The pm board id is 3449-0000-200
[0002.438] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.445] pm_ids_update: pm id update successful
[0002.475] Add serial number:1421919044435 as DT property
[0002.483] Applying platform configs
[0002.490] platform-init is not present. Skipping
[0002.494] calling apps_init()
[0002.500] Couldn't find GPT header
[0002.505] Proceeding to Cold Boot
[0002.508] starting app android_boot_app
[0002.511] Device state: unlocked
[0002.515] display console init
[0002.523] could not find regulator
[0002.546] hdmi cable not connected
[0002.549] is_hdmi_needed: HDMI not connected, returning false
[0002.555] hdmi is not connected
[0002.562] DT entry for leds-pwm not found
[0002.558] sor0 is not supported
[0002.569] display_console_init: no valid display out_type
[0002.577] subnode volume_up is not found !
[0002.581] subnode back is not found !
[0002.584] subnode volume_down is not found !
[0002.589] subnode menu is not found !
[0002.592] Gpio keyboard init success
[0002.673] found decompressor handler: lz4-legacy
[0002.687] decompressing blob (type 1)...
[0002.753] display_resolution: No display init
[0002.758] Failed to retrieve display resolution
[0002.762] Could not load/initialize BMP blob...ignoring
[0002.837] decompressor handler not found
[0002.841] load_firmware_blob: Firmware blob loaded, entries=2
[0002.847] XUSB blob version 0 size 124416 @ 0x92ca828c
[0002.853] -------> se_aes_verify_sbk_clear: 747
[0002.857] se_aes_verify_sbk_clear: Error
[0002.861] SE operation failed
[0002.864] bl_battery_charging: connected to external power supply
[0002.873] display_console_ioctl: No display init
[0002.877] switch_backlight failed
[0002.884] device_query_partition_size: failed to open partition spiflash0:MSC !
[0002.891] MSC Partition not found
[0002.897] device_query_partition_size: failed to open partition spiflash0:USP !
[0002.904] USP partition read failed!
[0002.908] blob_init: blob-partition USP header read failed
[0002.913] android_boot Unable to update recovery partition
[0002.919] kfs_getpartname: name = LNX
[0002.922] Loading kernel from LNX
[0002.932] Found 19 BFS partitions in "spiflash0"
[0003.250] load kernel from storage
[0003.255] decompressor handler not found
[0003.519] Successfully loaded kernel and ramdisk images
[0003.524] board ID = D78, board SKU = 0
[0003.529] sdmmc node status = okay
[0003.532] sdcard instance = 0
[0003.535] sdcard gpio handle 0x5b
[0003.538] sdcard gpio pin 0xc9
[0003.541] sdcard gpio flags 0x0
[0003.544] vmmc-supply 0x9e
[0003.547] cd_gpio_pin = 201
[0003.550] pin_state = 0
[0003.552] Found sdcard
[0003.554] SD-card IS present ...
[0003.557] load_and_boot_kernel: SD card detected OK
[0003.563] display_resolution: No display init
[0003.567] Failed to retrieve display resolution
[0003.572] bmp blob is not loaded and initialized
[0003.576] Failed to display boot-logo
[0003.580] NCK carveout not present
[0003.583] Skipping dts_overrides
[0003.586] NCK carveout not present
[0003.596] Find /i2c@7000c000's alias i2c0
[0003.600] get eeprom at 1-a0, size 256, type 0
[0003.609] Find /i2c@7000c500's alias i2c2
[0003.613] get eeprom at 3-a0, size 256, type 0
[0003.617] get eeprom at 3-ae, size 256, type 0
[0003.622] pm_ids_update: Updating 1,a0, size 256, type 0
[0003.627] I2C slave not started
[0003.630] I2C write failed
[0003.633] Writing offset failed
[0003.636] eeprom_init: EEPROM read failed
[0003.640] pm_ids_update: eeprom init failed
[0003.644] pm_ids_update: Updating 3,a0, size 256, type 0
[0003.674] pm_ids_update: The pm board id is 3448-0000-200
[0003.681] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0003.689] pm_ids_update: pm id update successful
[0003.694] pm_ids_update: Updating 3,ae, size 256, type 0
[0003.724] pm_ids_update: The pm board id is 3449-0000-200
[0003.730] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0003.738] pm_ids_update: pm id update successful
[0003.768] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0003.774] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0003.782] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0003.788] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0003.796] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:1d:8e
[0003.802] Plugin Manager: Parse ODM data 0x000a4000
[0003.815] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0003.823] Add serial number:1421919044435 as DT property
[0003.832] "bpmp" doesn't exist, creating
[0003.838] Updated bpmp info to DTB
[0003.843] Updated initrd info to DTB
[0003.846] "proc-board" doesn't exist, creating
[0003.852] Updated board info to DTB
[0003.855] "pmu-board" doesn't exist, creating
[0003.862] Updated board info to DTB
[0003.865] "display-board" doesn't exist, creating
[0003.871] Updated board info to DTB
[0003.874] "reset" doesn't exist, creating
[0003.879] Updated reset info to DTB
[0003.882] display_console_ioctl: No display init
[0003.887] display_console_ioctl: No display init
[0003.891] display_console_ioctl: No display init
[0003.896] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_su
[0003.930] DTB cmdline: earlycon=uart8250,mmio32,0x70006000
[0003.936] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0003.949] Updated bootarg info to DTB
[0003.953] Adding uuid 0000000164441643080000000f008340 to DT
[0003.959] Adding eks info 0 to DT
[0003.964] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0003.970] Updated memory info to DTB
[0003.976] Updated system-lp0-disable info to DTB
[0003.984] set vdd_core voltage to 1075 mv
[0003.988] setting 'vdd-core' regulator to 1075000 micro volts
[0003.994] Found secure-pmc; disable BPMP
[0000.162] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.167] Processing in cold boot mode Bootloader 2
[0000.172] A02 Bootrom Patch rev = 1023
[0000.176] Power-up reason: ap watchdog timeout
[0000.180] No Battery Present
[0000.182] pmic max77620 reset reason
[0000.186] pmic max77620 NVERC : 0x0
[0000.189] RamCode = 0
[0000.192] Platform has DDR4 type RAM
[0000.195] max77620 disabling SD1 Remote Sense
[0000.199] Setting DDR voltage to 1125mv
[0000.203] Serial Number of Pmic Max77663: 0x221ff9
[0000.211] Entering ramdump check
[0000.214] Get RamDumpCarveOut = 0x0
[0000.218] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.223] Last reboot was clean, booting normally!
[0000.228] Sdram initialization is successful
[0000.232] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.238] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.244] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.250] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.256] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.262] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.268] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.274] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.294] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.301] Platform-DebugCarveout: 0
[0000.304] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.310] Non secure mode, and RB not enabled.
[0000.314] BoardID = 3448, SKU = 0x0
[0000.318] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.322] Nano-SD: checking PT table on QSPI ...
[0000.326] Read PT from (2:0)
[0000.354] Using BFS PT to query partitions
[0000.361] Loading Tboot-CPU binary
[0000.415] Verifying TBC in OdmNonSecureSBK mode
[0000.426] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.433] Bootloader downloaded successfully.
[0000.437] Downloaded Tboot-CPU binary to 0xa0000258
[0000.443] MAX77620_GPIO5 configured
[0000.446] CPU power rail is up
[0000.449] CPU clock enabled
[0000.454] Performing RAM repair
[0000.457] Updating A64 Warmreset Address to 0xa00002e9
[0000.462] BoardID = 3448, SKU = 0x0
[0000.465] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.469] Nano-SD: checking PT table on QSPI ...
[0000.474] Loading NvTbootBootloaderDTB
[0000.603] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.716] Bootloader DTB Load Address: 0x83000000
[0000.721] BoardID = 3448, SKU = 0x0
[0000.724] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.728] Nano-SD: checking PT table on QSPI ...
[0000.733] Loading NvTbootKernelDTB
[0000.861] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.974] Kernel DTB Load Address: 0x83100000
[0000.978] BoardID = 3448, SKU = 0x0
[0000.982] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.985] Nano-SD: checking PT table on QSPI ...
[0000.993] Loading cboot binary
[0001.222] Verifying EBT in OdmNonSecureSBK mode
[0001.271] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0001.279] Bootloader downloaded successfully.
[0001.283] BoardID = 3448, SKU = 0x0
[0001.286] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.290] Nano-SD: checking PT table on QSPI ...
[0001.295] PT: Partition NCT NOT found !
[0001.299] Warning: Find Partition via PT Failed
[0001.303] Next binary entry address: 0x92c00258
[0001.308] BoardId: 3448
[0001.315] Overriding pmu board id with proc board id
[0001.319] Display board id is not available
[0001.324] BoardID = 3448, SKU = 0x0
[0001.327] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.331] Nano-SD: checking PT table on QSPI ...
[0001.537] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.610] /bpmp deleted
[0001.613] SC7EntryFw header found loaded at 0xff700000
[0001.861] OVR2 PMIC
[0001.863] Bpmp FW successfully loaded
[0001.867] BoardID = 3448, SKU = 0x0
[0001.870] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.874] Nano-SD: checking PT table on QSPI ...
[0001.880] WB0 init successfully at 0xff780000
[0001.885] Set NvDecSticky Bits
[0001.889] GSC2 address ff53fffc value c0edbbcc
[0001.897] GSC MC Settings done
[0001.900] BoardID = 3448, SKU = 0x0
[0001.904] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.908] Nano-SD: checking PT table on QSPI ...
[0001.914] TOS Image length 53680
[0001.917] Monitor size 53680
[0001.920] OS size 0
[0001.947] Secure Os AES-CMAC Verification Success!
[0001.951] TOS image cipher info: plaintext
[0001.955] Loading and Validation of Secure OS Successful
[0001.979] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.984] NvTbootPackSdramParams: start.
[0001.990] NvTbootPackSdramParams: done.
[0001.994] Tegraboot started after 88673 us
[0001.998] Basic modules init took 1279723 us
[0002.003] Sec Bootdevice Read Time = 24 ms, Read Size = 61 KB
[0002.008] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0002.014] Next stage binary read took 205687 us
[0002.018] Carveout took -232108 us
[0002.022] CPU initialization took 700504 us
[0002.026] Total time taken by TegraBoot 1953806 us
[0002.031] Starting CPU & Halting co-processor
64NOTICE: BL31: v1.3(release):5b49e7f80
NOTICE: BL31: Built : 14:33:23, Jan 15 2021
ERROR: Error initializing runtime service trusty_fast
[0002.153] RamCode = 0
[0002.158] LPDDR4 Training: Read DT: Number of tables = 2
[0002.163] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0002.176] EMC Training Successful
[0002.179] 408000 not found in DVFS table
[0002.185] RamCode = 0
[0002.189] DT Write: emc-table@204000 succeeded
[0002.194] DT Write: emc-table@1600000 succeeded
[0002.199] LPDDR4 Training: Write DT: Number of tables = 2
[0002.260]
[0002.261] Debug Init done
[0002.264] Marked DTB cacheable
[0002.267] Bootloader DTB loaded at 0x83000000
[0002.272] Marked DTB cacheable
[0002.275] Kernel DTB loaded at 0x83100000
[0002.279] DeviceTree Init done
[0002.292] Pinmux applied successfully
[0002.296] gicd_base: 0x50041000
[0002.299] gicc_base: 0x50042000
[0002.302] Interrupts Init done
[0002.307] Using base:0x60005090 & irq:208 for tick-timer
[0002.312] Using base:0x60005098 for delay-timer
[0002.316] platform_init_timer: DONE
[0002.320] Timer(tick) Init done
[0002.324] osc freq = 38400 khz
[0002.328]
[0002.329] Welcome to L4T Cboot
[0002.332]
[0002.333] Cboot Version: 00.00.2018.01-t210-39562017
[0002.338] calling constructors
[0002.341] initializing heap
[0002.343] initializing threads
[0002.346] initializing timers
[0002.349] creating bootstrap completion thread
[0002.354] top of bootstrap2()
[0002.357] CPU: ARM Cortex A57
[0002.359] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0002.364] initializing platform
[0002.372] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0002.376] ID LSB = 0x36, ID-CFI len = 194 bytes
[0002.381] Macronix QSPI chip present
[0002.384] SPI device register
[0002.387] init boot device
[0002.390] allocating memory for boot device(SPI)
[0002.395] registering boot device
[0002.403] QSPI bdev is already initialized
[0002.407] Enable APE clock
[0002.410] Un-powergate APE partition
[0002.413] of_register: registering tegra_udc to of_hal
[0002.418] of_register: registering inv20628-driver to of_hal
[0002.424] of_register: registering ads1015-driver to of_hal
[0002.430] of_register: registering lp8557-bl-driver to of_hal
[0002.435] of_register: registering bq2419x_charger to of_hal
[0002.441] of_register: registering bq27441_fuel_gauge to of_hal
[0002.453] gpio framework initialized
[0002.456] of_register: registering tca9539_gpio to of_hal
[0002.461] of_register: registering tca9539_gpio to of_hal
[0002.467] of_register: registering i2c_bus_driver to of_hal
[0002.472] of_register: registering i2c_bus_driver to of_hal
[0002.478] of_register: registering i2c_bus_driver to of_hal
[0002.484] pmic framework initialized
[0002.487] of_register: registering max77620_pmic to of_hal
[0002.493] regulator framework initialized
[0002.497] of_register: registering tps65132_bl_driver to of_hal
[0002.503] initializing target
[0002.508] gpio_driver_register: register 'tegra_gpio_driver' driver
[0002.517] board ID = D78, board SKU = 0
[0002.520] Skipping Z3!
[0002.525] fixed regulator driver initialized
[0002.543] initializing OF layer
[0002.546] NCK carveout not present
[0002.549] Skipping dts_overrides
[0002.554] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.571] I2C Bus Init done
[0002.573] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.584] I2C Bus Init done
[0002.586] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.597] I2C Bus Init done
[0002.599] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.610] I2C Bus Init done
[0002.613] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.623] I2C Bus Init done
[0002.626] of_children_init: Ops found for compatible string maxim,max77620
[0002.636] max77620_init using irq 118
[0002.641] register 'maxim,max77620' pmic
[0002.645] gpio_driver_register: register 'max77620-gpio' driver
[0002.652] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.662] I2C Bus Init done
[0002.666] NCK carveout not present
[0002.676] Find /i2c@7000c000's alias i2c0
[0002.679] get eeprom at 1-a0, size 256, type 0
[0002.688] Find /i2c@7000c500's alias i2c2
[0002.692] get eeprom at 3-a0, size 256, type 0
[0002.697] get eeprom at 3-ae, size 256, type 0
[0002.701] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.707] I2C slave not started
[0002.710] I2C write failed
[0002.712] Writing offset failed
[0002.715] eeprom_init: EEPROM read failed
[0002.719] pm_ids_update: eeprom init failed
[0002.723] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.754] pm_ids_update: The pm board id is 3448-0000-200
[0002.760] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.769] pm_ids_update: pm id update successful
[0002.773] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.804] pm_ids_update: The pm board id is 3449-0000-200
[0002.810] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.818] pm_ids_update: pm id update successful
[0002.848] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.854] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.862] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.868] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.876] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:1d:8e
[0002.883] Plugin Manager: Parse ODM data 0x000a4000
[0002.895] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0002.910] Find /i2c@7000c000's alias i2c0
[0002.914] get eeprom at 1-a0, size 256, type 0
[0002.923] Find /i2c@7000c500's alias i2c2
[0002.927] get eeprom at 3-a0, size 256, type 0
[0002.931] get eeprom at 3-ae, size 256, type 0
[0002.936] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.941] I2C slave not started
[0002.944] I2C write failed
[0002.947] Writing offset failed
[0002.950] eeprom_init: EEPROM read failed
[0002.954] pm_ids_update: eeprom init failed
[0002.958] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.988] pm_ids_update: The pm board id is 3448-0000-200
[0002.994] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0003.001] pm_ids_update: pm id update successful
[0003.006] pm_ids_update: Updating 3,ae, size 256, type 0
[0003.036] pm_ids_update: The pm board id is 3449-0000-200
[0003.042] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0003.049] pm_ids_update: pm id update successful
[0003.080] Add serial number:1421919044435 as DT property
[0003.087] Applying platform configs
[0003.094] platform-init is not present. Skipping
[0003.099] calling apps_init()
[0003.106] Couldn't find GPT header
[0003.111] Proceeding to Cold Boot
[0003.114] starting app android_boot_app
[0003.118] Device state: unlocked
[0003.121] display console init
[0003.130] could not find regulator
[0003.153] hdmi cable not connected
[0003.156] is_hdmi_needed: HDMIDT entry for leds-pwm not found
[0003.166] not connected, returning false
[0003.170] hdmi is not connected
[0003.173] sor0 is not supported
[0003.176] display_console_init: no valid display out_type
[0003.184] subnode volume_up is not found !
[0003.188] subnode back is not found !
[0003.192] subnode volume_down is not found !
[0003.196] subnode menu is not found !
[0003.199] Gpio keyboard init success
[0003.318] found decompressor handler: lz4-legacy
[0003.332] decompressing blob (type 1)...
[0003.399] display_resolution: No display init
[0003.403] Failed to retrieve display resolution
[0003.407] Could not load/initialize BMP blob...ignoring
[0003.516] decompressor handler not found
[0003.520] load_firmware_blob: Firmware blob loaded, entries=2
[0003.526] XUSB blob version 0 size 124416 @ 0x92ca828c
[0003.532] -------> se_aes_verify_sbk_clear: 747
[0003.536] se_aes_verify_sbk_clear: Error
[0003.540] SE operation failed
[0003.543] bl_battery_charging: connected to external power supply
[0003.552] display_console_ioctl: No display init
[0003.557] switch_backlight failed
[0003.564] device_query_partition_size: failed to open partition spiflash0:MSC !
[0003.572] MSC Partition not found
[0003.579] device_query_partition_size: failed to open partition spiflash0:USP !
[0003.587] USP partition read failed!
[0003.590] blob_init: blob-partition USP header read failed
[0003.596] android_boot Unable to update recovery partition
[0003.601] kfs_getpartname: name = LNX
[0003.605] Loading kernel from LNX
[0003.617] Found 19 BFS partitions in "spiflash0"
[0004.064] load kernel from storage
[0004.069] decompressor handler not found
[0000.162] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.167] Processing in cold boot mode Bootloader 2
[0000.172] A02 Bootrom Patch rev = 1023
[0000.176] Power-up reason: ap watchdog timeout
[0000.180] No Battery Present
[0000.182] pmic max77620 reset reason
[0000.186] pmic max77620 NVERC : 0x0
[0000.189] RamCode = 0
[0000.192] Platform has DDR4 type RAM
[0000.195] max77620 disabling SD1 Remote Sense
[0000.199] Setting DDR voltage to 1125mv
[0000.203] Serial Number of Pmic Max77663: 0x221ff9
[0000.211] Entering ramdump check
[0000.214] Get RamDumpCarveOut = 0x0
[0000.218] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.223] Last reboot was clean, booting normally!
[0000.228] Sdram initialization is successful
[0000.232] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.238] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.244] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.250] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.256] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.262] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.268] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.274] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.294] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.301] Platform-DebugCarveout: 0
[0000.304] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.310] Non secure mode, and RB not enabled.
[0000.314] BoardID = 3448, SKU = 0x0
[0000.318] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.322] Nano-SD: checking PT table on QSPI ...
[0000.326] Read PT from (2:0)
[0000.354] Using BFS PT to query partitions
[0000.361] Loading Tboot-CPU binary
[0000.415] Verifying TBC in OdmNonSecureSBK mode
[0000.426] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.433] Bootloader downloaded successfully.
[0000.437] Downloaded Tboot-CPU binary to 0xa0000258
[0000.443] MAX77620_GPIO5 configured
[0000.446] CPU power rail is up
[0000.449] CPU clock enabled
[0000.454] Performing RAM repair
[0000.457] Updating A64 Warmreset Address to 0xa00002e9
[0000.462] BoardID = 3448, SKU = 0x0
[0000.465] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.469] Nano-SD: checking PT table on QSPI ...
[0000.474] Loading NvTbootBootloaderDTB
[0000.603] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.716] Bootloader DTB Load Address: 0x83000000
[0000.721] BoardID = 3448, SKU = 0x0
[0000.724] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.728] Nano-SD: checking PT table on QSPI ...
[0000.733] Loading NvTbootKernelDTB
[0000.861] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.974] Kernel DTB Load Address: 0x83100000
[0000.978] BoardID = 3448, SKU = 0x0
[0000.982] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.985] Nano-SD: checking PT table on QSPI ...
[0000.993] Loading cboot binary
[0001.222] Verifying EBT in OdmNonSecureSBK mode
[0001.271] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0001.279] Bootloader downloaded successfully.
[0001.283] BoardID = 3448, SKU = 0x0
[0001.286] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.290] Nano-SD: checking PT table on QSPI ...
[0001.295] PT: Partition NCT NOT found !
[0001.299] Warning: Find Partition via PT Failed
[0001.303] Next binary entry address: 0x92c00258
[0001.308] BoardId: 3448
[0001.315] Overriding pmu board id with proc board id
[0001.319] Display board id is not available
[0001.324] BoardID = 3448, SKU = 0x0
[0001.327] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.331] Nano-SD: checking PT table on QSPI ...
[0001.537] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.610] /bpmp deleted
[0001.613] SC7EntryFw header found loaded at 0xff700000
[0001.861] OVR2 PMIC
[0001.863] Bpmp FW successfully loaded
[0001.867] BoardID = 3448, SKU = 0x0
[0001.870] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.874] Nano-SD: checking PT table on QSPI ...
[0001.880] WB0 init successfully at 0xff780000
[0001.885] Set NvDecSticky Bits
[0001.889] GSC2 address ff53fffc value c0edbbcc
[0001.897] GSC MC Settings done
[0001.900] BoardID = 3448, SKU = 0x0
[0001.904] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.908] Nano-SD: checking PT table on QSPI ...
[0001.914] TOS Image length 53680
[0001.917] Monitor size 53680
[0001.920] OS size 0
[0001.947] Secure Os AES-CMAC Verification Success!
[0001.951] TOS image cipher info: plaintext
[0001.955] Loading and Validation of Secure OS Successful
[0001.979] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.984] NvTbootPackSdramParams: start.
[0001.990] NvTbootPackSdramParams: done.
[0001.994] Tegraboot started after 88673 us
[0001.998] Basic modules init took 1279740 us
[0002.003] Sec Bootdevice Read Time = 24 ms, Read Size = 61 KB
[0002.008] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0002.014] Next stage binary read took 205686 us
[0002.018] Carveout took -232108 us
[0002.022] CPU initialization took 700496 us
[0002.026] Total time taken by TegraBoot 1953814 us
[0002.031] Starting CPU & Halting co-processor
64NOTICE: BL31: v1.3(release):5b49e7f80
NOTICE: BL31: Built : 14:33:23, Jan 15 2021
ERROR: Error initializing runtime service trusty_fast
[0002.153] RamCode = 0
[0002.158] LPDDR4 Training: Read DT: Number of tables = 2
[0002.163] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0002.176] EMC Training Successful
[0002.179] 408000 not found in DVFS table
[0002.186] RamCode = 0
[0002.189] DT Write: emc-table@204000 succeeded
[0002.194] DT Write: emc-table@1600000 succeeded
[0002.199] LPDDR4 Training: Write DT: Number of tables = 2
[0002.260]
[0002.261] Debug Init done
[0002.264] Marked DTB cacheable
[0002.267] Bootloader DTB loaded at 0x83000000
[0002.272] Marked DTB cacheable
[0002.275] Kernel DTB loaded at 0x83100000
[0002.279] DeviceTree Init done
[0002.292] Pinmux applied successfully
[0002.296] gicd_base: 0x50041000
[0002.299] gicc_base: 0x50042000
[0002.302] Interrupts Init done
[0002.307] Using base:0x60005090 & irq:208 for tick-timer
[0002.312] Using base:0x60005098 for delay-timer
[0002.316] platform_init_timer: DONE
[0002.320] Timer(tick) Init done
[0002.324] osc freq = 38400 khz
[0002.328]
[0002.329] Welcome to L4T Cboot
[0002.332]
[0002.333] Cboot Version: 00.00.2018.01-t210-39562017
[0002.338] calling constructors
[0002.341] initializing heap
[0002.343] initializing threads
[0002.346] initializing timers
[0002.349] creating bootstrap completion thread
[0002.354] top of bootstrap2()
[0002.357] CPU: ARM Cortex A57
[0002.359] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0002.364] initializing platform
[0002.372] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0002.376] ID LSB = 0x36, ID-CFI len = 194 bytes
[0002.381] Macronix QSPI chip present
[0002.384] SPI device register
[0002.387] init boot device
[0002.390] allocating memory for boot device(SPI)
[0002.395] registering boot device
[0002.403] QSPI bdev is already initialized
[0002.407] Enable APE clock
[0002.410] Un-powergate APE partition
[0002.413] of_register: registering tegra_udc to of_hal
[0002.418] of_register: registering inv20628-driver to of_hal
[0002.424] of_register: registering ads1015-driver to of_hal
[0002.430] of_register: registering lp8557-bl-driver to of_hal
[0002.435] of_register: registering bq2419x_charger to of_hal
[0002.441] of_register: registering bq27441_fuel_gauge to of_hal
[0002.453] gpio framework initialized
[0002.456] of_register: registering tca9539_gpio to of_hal
[0002.461] of_register: registering tca9539_gpio to of_hal
[0002.467] of_register: registering i2c_bus_driver to of_hal
[0002.472] of_register: registering i2c_bus_driver to of_hal
[0002.478] of_register: registering i2c_bus_driver to of_hal
[0002.484] pmic framework initialized
[0002.487] of_register: registering max77620_pmic to of_hal
[0002.493] regulator framework initialized
[0002.497] of_register: registering tps65132_bl_driver to of_hal
[0002.503] initializing target
[0002.508] gpio_driver_register: register 'tegra_gpio_driver' driver
[0002.517] board ID = D78, board SKU = 0
[0002.520] Skipping Z3!
[0002.525] fixed regulator driver initialized
[0002.543] initializing OF layer
[0002.546] NCK carveout not present
[0002.549] Skipping dts_overrides
[0002.554] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.571] I2C Bus Init done
[0002.573] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.584] I2C Bus Init done
[0002.586] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.597] I2C Bus Init done
[0002.599] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.610] I2C Bus Init done
[0002.613] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.623] I2C Bus Init done
[0002.626] of_children_init: Ops found for compatible string maxim,max77620
[0002.636] max77620_init using irq 118
[0002.641] register 'maxim,max77620' pmic
[0002.645] gpio_driver_register: register 'max77620-gpio' driver
[0002.652] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.662] I2C Bus Init done
[0002.666] NCK carveout not present
[0002.676] Find /i2c@7000c000's alias i2c0
[0002.679] get eeprom at 1-a0, size 256, type 0
[0002.688] Find /i2c@7000c500's alias i2c2
[0002.692] get eeprom at 3-a0, size 256, type 0
[0002.697] get eeprom at 3-ae, size 256, type 0
[0002.701] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.707] I2C slave not started
[0002.710] I2C write failed
[0002.712] Writing offset failed
[0002.715] eeprom_init: EEPROM read failed
[0002.719] pm_ids_update: eeprom init failed
[0002.723] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.754] pm_ids_update: The pm board id is 3448-0000-200
[0002.760] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.769] pm_ids_update: pm id update successful
[0002.773] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.804] pm_ids_update: The pm board id is 3449-0000-200
[0002.810] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.818] pm_ids_update: pm id update successful
[0002.848] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.854] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.862] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.868] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.876] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:1d:8e
[0002.883] Plugin Manager: Parse ODM data 0x000a4000
[0002.895] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0002.910] Find /i2c@7000c000's alias i2c0
[0002.914] get eeprom at 1-a0, size 256, type 0
[0002.923] Find /i2c@7000c500's alias i2c2
[0002.927] get eeprom at 3-a0, size 256, type 0
[0002.931] get eeprom at 3-ae, size 256, type 0
[0002.936] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.941] I2C slave not started
[0002.944] I2C write failed
[0002.947] Writing offset failed
[0002.950] eeprom_init: EEPROM read failed
[0002.954] pm_ids_update: eeprom init failed
[0002.958] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.988] pm_ids_update: The pm board id is 3448-0000-200
[0002.994] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0003.001] pm_ids_update: pm id update successful
[0003.006] pm_ids_update: Updating 3,ae, size 256, type 0
[0003.036] pm_ids_update: The pm board id is 3449-0000-200
[0003.042] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0003.049] pm_ids_update: pm id update successful
[0003.079] Add serial number:1421919044435 as DT property
[0003.087] Applying platform configs
[0003.094] platform-init is not present. Skipping
[0003.099] calling apps_init()
[0003.106] Couldn't find GPT header
[0003.111] Proceeding to Cold Boot
[0003.114] starting app android_boot_app
[0003.118] Device state: unlocked
[0003.121] display console init
[0003.130] could not find regulator
[0003.153] hdmi cable not connected
[0003.156] is_hdmi_needed: HDMI nDT entry for leds-pwm not found
o[0003.166] t connected, returning false
[0003.169] hdmi is not connected
[0003.172] sor0 is not supported
[0003.175] display_console_init: no valid display out_type
[0003.184] subnode volume_up is not found !
[0003.188] subnode back is not found !
[0003.191] subnode volume_down is not found !
[0003.196] subnode menu is not found !
[0003.199] Gpio keyboard init success
[0003.318] found decompressor handler: lz4-legacy
[0003.332] decompressing blob (type 1)...
[0003.398] display_resolution: No display init
[0003.403] Failed to retrieve display resolution
[0003.407] Could not load/initialize BMP blob...ignoring
[0003.516] decompressor handler not found
[0003.520] load_firmware_blob: Firmware blob loaded, entries=2
[0003.526] XUSB blob version 0 size 124416 @ 0x92ca828c
[0003.532] -------> se_aes_verify_sbk_clear: 747
[0003.536] se_aes_verify_sbk_clear: Error
[0003.540] SE operation failed
[0003.543] bl_battery_charging: connected to external power supply
[0003.552] display_console_ioctl: No display init
[0003.557] switch_backlight failed
[0003.564] device_query_partition_size: failed to open partition spiflash0:MSC !
[0003.572] MSC Partition not found
[0003.579] device_query_partition_size: failed to open partition spiflash0:USP !
[0003.587] USP partition read failed!
[0003.590] blob_init: blob-partition USP header read failed
[0003.596] android_boot Unable to update recovery partition
[0003.601] kfs_getpartname: name = LNX
[0003.605] Loading kernel from LNX
[0003.617] Found 19 BFS partitions in "spiflash0"
[0004.063] load kernel from storage
[0004.069] decompressor handler not found
[0000.162] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.167] Processing in cold boot mode Bootloader 2
[0000.172] A02 Bootrom Patch rev = 1023
[0000.176] Power-up reason: ap watchdog timeout
[0000.180] No Battery Present
[0000.182] pmic max77620 reset reason
[0000.186] pmic max77620 NVERC : 0x0
[0000.189] RamCode = 0
[0000.192] Platform has DDR4 type RAM
[0000.195] max77620 disabling SD1 Remote Sense
[0000.199] Setting DDR voltage to 1125mv
[0000.203] Serial Number of Pmic Max77663: 0x221ff9
[0000.211] Entering ramdump check
[0000.214] Get RamDumpCarveOut = 0x0
[0000.218] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.223] Last reboot was clean, booting normally!
[0000.228] Sdram initialization is successful
[0000.232] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.238] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.244] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.250] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.256] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.262] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.268] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.274] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.294] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.301] Platform-DebugCarveout: 0
[0000.304] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.310] Non secure mode, and RB not enabled.
[0000.314] BoardID = 3448, SKU = 0x0
[0000.318] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.322] Nano-SD: checking PT table on QSPI ...
[0000.326] Read PT from (2:0)
[0000.354] Using BFS PT to query partitions
[0000.361] Loading Tboot-CPU binary
[0000.415] Verifying TBC in OdmNonSecureSBK mode
[0000.426] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.433] Bootloader downloaded successfully.
[0000.437] Downloaded Tboot-CPU binary to 0xa0000258
[0000.443] MAX77620_GPIO5 configured
[0000.446] CPU power rail is up
[0000.449] CPU clock enabled
[0000.454] Performing RAM repair
[0000.457] Updating A64 Warmreset Address to 0xa00002e9
[0000.462] BoardID = 3448, SKU = 0x0
[0000.465] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.469] Nano-SD: checking PT table on QSPI ...
[0000.474] Loading NvTbootBootloaderDTB
[0000.603] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.716] Bootloader DTB Load Address: 0x83000000
[0000.721] BoardID = 3448, SKU = 0x0
[0000.724] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.728] Nano-SD: checking PT table on QSPI ...
[0000.733] Loading NvTbootKernelDTB
[0000.861] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.974] Kernel DTB Load Address: 0x83100000
[0000.978] BoardID = 3448, SKU = 0x0
[0000.982] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.985] Nano-SD: checking PT table on QSPI ...
[0000.993] Loading cboot binary
[0001.222] Verifying EBT in OdmNonSecureSBK mode
[0001.271] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0001.279] Bootloader downloaded successfully.
[0001.283] BoardID = 3448, SKU = 0x0
[0001.286] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.290] Nano-SD: checking PT table on QSPI ...
[0001.295] PT: Partition NCT NOT found !
[0001.299] Warning: Find Partition via PT Failed
[0001.303] Next binary entry address: 0x92c00258
[0001.308] BoardId: 3448
[0001.315] Overriding pmu board id with proc board id
[0001.319] Display board id is not available
[0001.324] BoardID = 3448, SKU = 0x0
[0001.327] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.331] Nano-SD: checking PT table on QSPI ...
[0001.537] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.610] /bpmp deleted
[0001.613] SC7EntryFw header found loaded at 0xff700000
[0001.861] OVR2 PMIC
[0001.863] Bpmp FW successfully loaded
[0001.867] BoardID = 3448, SKU = 0x0
[0001.870] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.874] Nano-SD: checking PT table on QSPI ...
[0001.880] WB0 init successfully at 0xff780000
[0001.885] Set NvDecSticky Bits
[0001.889] GSC2 address ff53fffc value c0edbbcc
[0001.897] GSC MC Settings done
[0001.900] BoardID = 3448, SKU = 0x0
[0001.904] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.908] Nano-SD: checking PT table on QSPI ...
[0001.914] TOS Image length 53680
[0001.917] Monitor size 53680
[0001.920] OS size 0
[0001.947] Secure Os AES-CMAC Verification Success!
[0001.951] TOS image cipher info: plaintext
[0001.955] Loading and Validation of Secure OS Successful
[0001.979] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.984] NvTbootPackSdramParams: start.
[0001.990] NvTbootPackSdramParams: done.
[0001.994] Tegraboot started after 88673 us
[0001.998] Basic modules init took 1279716 us
[0002.003] Sec Bootdevice Read Time = 24 ms, Read Size = 61 KB
[0002.008] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0002.014] Next stage binary read took 205685 us
[0002.018] Carveout took -232106 us
[0002.022] CPU initialization took 700495 us
[0002.026] Total time taken by TegraBoot 1953790 us
[0002.031] Starting CPU & Halting co-processor
64NOTICE: BL31: v1.3(release):5b49e7f80
NOTICE: BL31: Built : 14:33:23, Jan 15 2021
ERROR: Error initializing runtime service trusty_fast
[0002.153] RamCode = 0
[0002.158] LPDDR4 Training: Read DT: Number of tables = 2
[0002.163] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0002.176] EMC Training Successful
[0002.179] 408000 not found in DVFS table
[0002.185] RamCode = 0
[0002.189] DT Write: emc-table@204000 succeeded
[0002.194] DT Write: emc-table@1600000 succeeded
[0002.199] LPDDR4 Training: Write DT: Number of tables = 2
[0002.260]
[0002.261] Debug Init done
[0002.264] Marked DTB cacheable
[0002.267] Bootloader DTB loaded at 0x83000000
[0002.272] Marked DTB cacheable
[0002.275] Kernel DTB loaded at 0x83100000
[0002.278] DeviceTree Init done
[0002.292] Pinmux applied successfully
[0002.296] gicd_base: 0x50041000
[0002.299] gicc_base: 0x50042000
[0002.302] Interrupts Init done
[0002.307] Using base:0x60005090 & irq:208 for tick-timer
[0002.312] Using base:0x60005098 for delay-timer
[0002.316] platform_init_timer: DONE
[0002.320] Timer(tick) Init done
[0002.324] osc freq = 38400 khz
[0002.327]
[0002.329] Welcome to L4T Cboot
[0002.332]
[0002.333] Cboot Version: 00.00.2018.01-t210-39562017
[0002.338] calling constructors
[0002.341] initializing heap
[0002.343] initializing threads
[0002.346] initializing timers
[0002.349] creating bootstrap completion thread
[0002.354] top of bootstrap2()
[0002.357] CPU: ARM Cortex A57
[0002.359] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0002.364] initializing platform
[0002.372] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0002.376] ID LSB = 0x36, ID-CFI len = 194 bytes
[0002.381] Macronix QSPI chip present
[0002.384] SPI device register
[0002.387] init boot device
[0002.390] allocating memory for boot device(SPI)
[0002.394] registering boot device
[0002.403] QSPI bdev is already initialized
[0002.407] Enable APE clock
[0002.410] Un-powergate APE partition
[0002.413] of_register: registering tegra_udc to of_hal
[0002.418] of_register: registering inv20628-driver to of_hal
[0002.424] of_register: registering ads1015-driver to of_hal
[0002.429] of_register: registering lp8557-bl-driver to of_hal
[0002.435] of_register: registering bq2419x_charger to of_hal
[0002.441] of_register: registering bq27441_fuel_gauge to of_hal
[0002.453] gpio framework initialized
[0002.456] of_register: registering tca9539_gpio to of_hal
[0002.461] of_register: registering tca9539_gpio to of_hal
[0002.467] of_register: registering i2c_bus_driver to of_hal
[0002.472] of_register: registering i2c_bus_driver to of_hal
[0002.478] of_register: registering i2c_bus_driver to of_hal
[0002.484] pmic framework initialized
[0002.487] of_register: registering max77620_pmic to of_hal
[0002.493] regulator framework initialized
[0002.497] of_register: registering tps65132_bl_driver to of_hal
[0002.503] initializing target
[0002.508] gpio_driver_register: register 'tegra_gpio_driver' driver
[0002.517] board ID = D78, board SKU = 0
[0002.520] Skipping Z3!
[0002.525] fixed regulator driver initialized
[0002.543] initializing OF layer
[0002.546] NCK carveout not present
[0002.549] Skipping dts_overrides
[0002.553] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.571] I2C Bus Init done
[0002.573] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.584] I2C Bus Init done
[0002.586] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.597] I2C Bus Init done
[0002.599] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.610] I2C Bus Init done
[0002.612] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.623] I2C Bus Init done
[0002.626] of_children_init: Ops found for compatible string maxim,max77620
[0002.636] max77620_init using irq 118
[0002.641] register 'maxim,max77620' pmic
[0002.645] gpio_driver_register: register 'max77620-gpio' driver
[0002.652] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.662] I2C Bus Init done
[0002.666] NCK carveout not present
[0002.676] Find /i2c@7000c000's alias i2c0
[0002.679] get eeprom at 1-a0, size 256, type 0
[0002.688] Find /i2c@7000c500's alias i2c2
[0002.692] get eeprom at 3-a0, size 256, type 0
[0002.697] get eeprom at 3-ae, size 256, type 0
[0002.701] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.707] I2C slave not started
[0002.710] I2C write failed
[0002.712] Writing offset failed
[0002.715] eeprom_init: EEPROM read failed
[0002.719] pm_ids_update: eeprom init failed
[0002.723] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.753] pm_ids_update: The pm board id is 3448-0000-200
[0002.760] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.769] pm_ids_update: pm id update successful
[0002.773] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.804] pm_ids_update: The pm board id is 3449-0000-200
[0002.810] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.818] pm_ids_update: pm id update successful
[0002.848] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.854] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.862] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.868] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.876] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:1d:8e
[0002.883] Plugin Manager: Parse ODM data 0x000a4000
[0002.895] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0002.910] Find /i2c@7000c000's alias i2c0
[0002.914] get eeprom at 1-a0, size 256, type 0
[0002.923] Find /i2c@7000c500's alias i2c2
[0002.927] get eeprom at 3-a0, size 256, type 0
[0002.931] get eeprom at 3-ae, size 256, type 0
[0002.936] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.941] I2C slave not started
[0002.944] I2C write failed
[0002.947] Writing offset failed
[0002.950] eeprom_init: EEPROM read failed
[0002.954] pm_ids_update: eeprom init failed
[0002.958] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.988] pm_ids_update: The pm board id is 3448-0000-200
[0002.994] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0003.001] pm_ids_update: pm id update successful
[0003.006] pm_ids_update: Updating 3,ae, size 256, type 0
[0003.036] pm_ids_update: The pm board id is 3449-0000-200
[0003.042] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0003.049] pm_ids_update: pm id update successful
[0003.080] Add serial number:1421919044435 as DT property
[0003.087] Applying platform configs
[0003.094] platform-init is not present. Skipping
[0003.099] calling apps_init()
[0003.106] Couldn't find GPT header
[0003.111] Proceeding to Cold Boot
[0003.114] starting app android_boot_app
[0003.118] Device state: unlocked
[0003.121] display console init
[0003.130] could not find regulator
[0003.153] hdmi cable not connected
[0003.156] is_hdmi_needed: HDMI DT entry for leds-pwm not found
n[0003.166] ot connected, returning false
[0003.169] hdmi is not connected
[0003.173] sor0 is not supported
[0003.176] display_console_init: no valid display out_type
[0003.184] subnode volume_up is not found !
[0003.188] subnode back is not found !
[0003.191] subnode volume_down is not found !
[0003.196] subnode menu is not found !
[0003.199] Gpio keyboard init success
[0003.318] found decompressor handler: lz4-legacy
[0003.332] decompressing blob (type 1)...
[0003.398] display_resolution: No display init
[0003.403] Failed to retrieve display resolution
[0003.407] Could not load/initialize BMP blob...ignoring
[0003.516] decompressor handler not found
[0003.520] load_firmware_blob: Firmware blob loaded, entries=2
[0003.526] XUSB blob version 0 size 124416 @ 0x92ca828c
[0003.532] -------> se_aes_verify_sbk_clear: 747
[0003.536] se_aes_verify_sbk_clear: Error
[0003.540] SE operation failed
[0003.543] bl_battery_charging: connected to external power supply
[0003.552] display_console_ioctl: No display init
[0003.557] switch_backlight failed
[0003.564] device_query_partition_size: failed to open partition spiflash0:MSC !
[0003.572] MSC Partition not found
[0003.579] device_query_partition_size: failed to open partition spiflash0:USP !
[0003.587] USP partition read failed!
[0003.590] blob_init: blob-partition USP header read failed
[0003.596] android_boot Unable to update recovery partition
[0003.601] kfs_getpartname: name = LNX
[0003.605] Loading kernel from LNX
[0003.617] Found 19 BFS partitions in "spiflash0"
[0004.063] load kernel from storage
[0004.069] decompressor handler not found
[0000.162] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.167] Processing in cold boot mode Bootloader 2
[0000.172] A02 Bootrom Patch rev = 1023
[0000.176] Power-up reason: ap watchdog timeout
[0000.180] No Battery Present
[0000.182] pmic max77620 reset reason
[0000.186] pmic max77620 NVERC : 0x0
[0000.189] RamCode = 0
[0000.192] Platform has DDR4 type RAM
[0000.195] max77620 disabling SD1 Remote Sense
[0000.199] Setting DDR voltage to 1125mv
[0000.203] Serial Number of Pmic Max77663: 0x221ff9
[0000.211] Entering ramdump check
[0000.214] Get RamDumpCarveOut = 0x0
[0000.218] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.223] Last reboot was clean, booting normally!
[0000.228] Sdram initialization is successful
[0000.232] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.238] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.244] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.250] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.256] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.262] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.268] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.274] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.294] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.301] Platform-DebugCarveout: 0
[0000.304] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
First: I’ve extracted in new directory clean L4T 32.5
tar -xjf Tegra210_Linux_R32.5.0_aarch64.tbz2
tar -xjf secureboot_R32.5.0_aarch64.tbz2
cd Linux_for_Tegra/rootfs/
tar -xjf Tegra_Linux_Sample-Root-Filesystem_R32.5.0_aarch64.tbz2
cd …
./apply_binaries.sh
Here it is the flash.sh output:
root@tchome:/l4t/Linux_for_Tegra# ./flash.sh jetson-nano-qspi-sd.conf ./flash.sh jetson-nano-qspi-sd mmcblk0p1
###############################################################################
# L4T BSP Information:
# R32 , REVISION: 5.0
###############################################################################
# Target Board Information:
# Name: jetson-nano-qspi-sd, Board Family: t210ref, SoC: Tegra 210,
# OpMode: production, Boot Authentication: NS,
# Disk encryption: disabled ,
###############################################################################
./tegraflash.py --chip 0x21 --applet "/l4t/Linux_for_Tegra/bootloader/nvtboot_recovery.bin" --skipuid --cmd "dump eeprom boardinfo cvm.bin"
/l4t/Linux_for_Tegra/bootloader/tegraflash_internal.py:1978: SyntaxWarning: "is not" with a literal. Did you mean "!="?
if sig_type is not "zerosbk":
/l4t/Linux_for_Tegra/bootloader/tegraflash_internal.py:1981: SyntaxWarning: "is" with a literal. Did you mean "=="?
if sig_type is "oem-rsa":
/l4t/Linux_for_Tegra/bootloader/tegraflash_internal.py:2416: SyntaxWarning: "is not" with a literal. Did you mean "!="?
while count is not 0 and not check_ismb2():
/l4t/Linux_for_Tegra/bootloader/tegraflash_internal.py:2425: SyntaxWarning: "is not" with a literal. Did you mean "!="?
while count is not 0:
Welcome to Tegra Flash
version 1.0.0
Type ? or help for help and q or quit to exit
Use ! to execute system commands
[ 0.0008 ] Generating RCM messages
[ 0.0016 ] tegrarcm --listrcm rcm_list.xml --chip 0x21 0 --download rcm /l4t/Linux_for_Tegra/bootloader/nvtboot_recovery.bin 0 0
[ 0.0023 ] RCM 0 is saved as rcm_0.rcm
[ 0.0026 ] RCM 1 is saved as rcm_1.rcm
[ 0.0026 ] List of rcm files are saved in rcm_list.xml
[ 0.0026 ]
[ 0.0027 ] Signing RCM messages
[ 0.0033 ] tegrasign --key None --list rcm_list.xml --pubkeyhash pub_key.key
[ 0.0040 ] Assuming zero filled SBK key
[ 0.0082 ]
[ 0.0083 ] Copying signature to RCM mesages
[ 0.0092 ] tegrarcm --chip 0x21 0 --updatesig rcm_list_signed.xml
[ 0.0102 ]
[ 0.0103 ] Boot Rom communication
[ 0.0110 ] tegrarcm --chip 0x21 0 --rcm rcm_list_signed.xml --skipuid
[ 0.0117 ] RCM version 0X210001
[ 0.0558 ] Boot Rom communication completed
[ 1.0642 ]
[ 1.0644 ] dump EEPROM info
[ 1.0690 ] tegrarcm --oem platformdetails eeprom /l4t/Linux_for_Tegra/bootloader/cvm.bin
[ 1.0727 ] Applet version 00.01.0000
[ 1.0892 ] Saved platform info in /l4t/Linux_for_Tegra/bootloader/cvm.bin
[ 1.1684 ]
[ 1.1724 ] tegrarcm --reboot recovery
[ 1.1759 ] Applet version 00.01.0000
[ 1.1936 ]
Board ID(3448) version(200)
creating dummy /l4t/Linux_for_Tegra/bootloader/badpage.bin
1+0 прочетени блока
1+0 записани блока
изкопирани са 4096 байта (4,1 kB, 4,0 KiB), 0,000132542 s, 30,9 MB/s
copying bctfile(/l4t/Linux_for_Tegra/bootloader/t210ref/BCT/P3448_A00_lpddr4_204Mhz_P987.cfg)... done.
copying bootloader(/l4t/Linux_for_Tegra/bootloader/t210ref/cboot.bin)... done.
copying initrd(/l4t/Linux_for_Tegra/bootloader/l4t_initrd.img)... done.
populating kernel to rootfs... done.
populating initrd to rootfs... done.
populating /l4t/Linux_for_Tegra/kernel/dtb/tegra210-p3448-0000-p3449-0000-a02.dtb to rootfs... done.
Making Boot image... done.
Existing sosfile(/l4t/Linux_for_Tegra/bootloader/nvtboot_recovery.bin) reused.
copying tegraboot(/l4t/Linux_for_Tegra/bootloader/t210ref/nvtboot.bin)... done.
copying cpu_bootloader(/l4t/Linux_for_Tegra/bootloader/t210ref/cboot.bin)... done.
copying bpffile(/l4t/Linux_for_Tegra/bootloader/t210ref/sc7entry-firmware.bin)... done.
Existing badpagefile(/l4t/Linux_for_Tegra/bootloader/badpage.bin) reused.
copying wb0boot(/l4t/Linux_for_Tegra/bootloader/t210ref/warmboot.bin)... done.
Existing tosfile(/l4t/Linux_for_Tegra/bootloader/tos-mon-only.img) reused.
Existing eksfile(/l4t/Linux_for_Tegra/bootloader/eks.img) reused.
copying dtbfile(/l4t/Linux_for_Tegra/kernel/dtb/tegra210-p3448-0000-p3449-0000-a02.dtb)... done.
Copying nv_boot_control.conf to rootfs
Making system.img...
populating rootfs from /l4t/Linux_for_Tegra/rootfs ... done.
populating /boot/extlinux/extlinux.conf ... done.
Sync'ing system.img ... done.
Converting RAW image to Sparse image... done.
system.img built successfully.
Existing tbcfile(/l4t/Linux_for_Tegra/bootloader/nvtboot_cpu.bin) reused.
copying tbcdtbfile(/l4t/Linux_for_Tegra/kernel/dtb/tegra210-p3448-0000-p3449-0000-a02.dtb)... done.
copying cfgfile(/l4t/Linux_for_Tegra/bootloader/t210ref/cfg/flash_l4t_t210_max-spi_sd_p3448.xml) to flash.xml... done.
copying flasher(/l4t/Linux_for_Tegra/bootloader/t210ref/cboot.bin)... done.
Existing flashapp(/l4t/Linux_for_Tegra/bootloader/tegraflash.py) reused.
./tegraflash.py --bl cboot.bin --bct P3448_A00_lpddr4_204Mhz_P987.cfg --odmdata 0xa4000 --bldtb kernel_tegra210-p3448-0000-p3449-0000-a02.dtb --applet nvtboot_recovery.bin --cmd "flash; reboot" --cfg flash.xml --chip 0x21 --bins "EBT cboot.bin; DTB tegra210-p3448-0000-p3449-0000-a02.dtb"
saving flash command in /l4t/Linux_for_Tegra/bootloader/flashcmd.txt
saving Windows flash command to /l4t/Linux_for_Tegra/bootloader/flash_win.bat
*** Flashing target device started. ***
Welcome to Tegra Flash
version 1.0.0
Type ? or help for help and q or quit to exit
Use ! to execute system commands
[ 0.0349 ] tegrasign --key None --getmode mode.txt
[ 0.0358 ] Assuming zero filled SBK key
[ 0.0805 ]
[ 0.0808 ] Generating RCM messages
[ 0.1132 ] tegrarcm --listrcm rcm_list.xml --chip 0x21 0 --download rcm nvtboot_recovery.bin 0 0
[ 0.1161 ] RCM 0 is saved as rcm_0.rcm
[ 0.1325 ] RCM 1 is saved as rcm_1.rcm
[ 0.1325 ] List of rcm files are saved in rcm_list.xml
[ 0.1325 ]
[ 0.1326 ] Signing RCM messages
[ 0.1356 ] tegrasign --key None --list rcm_list.xml --pubkeyhash pub_key.key
[ 0.1383 ] Assuming zero filled SBK key
[ 0.1576 ]
[ 0.1577 ] Copying signature to RCM mesages
[ 0.1608 ] tegrarcm --chip 0x21 0 --updatesig rcm_list_signed.xml
[ 0.1651 ]
[ 0.1652 ] Parsing partition layout
[ 0.1892 ] tegraparser --pt flash.xml.tmp
[ 0.1970 ]
[ 0.1972 ] Creating list of images to be signed
[ 0.2118 ] tegrahost --chip 0x21 0 --partitionlayout flash.xml.bin --list images_list.xml
[ 0.3090 ]
[ 0.3092 ] Generating signatures
[ 0.3122 ] tegrasign --key None --list images_list.xml --pubkeyhash pub_key.key
[ 0.3149 ] Assuming zero filled SBK key
[ 0.4502 ]
[ 0.4503 ] Generating br-bct
[ 0.4971 ] tegrabct --bct P3448_A00_lpddr4_204Mhz_P987.cfg --chip 0x21 0
[ 0.4998 ] Copying Sdram info from 2 to 3 set
[ 0.5404 ]
[ 0.5405 ] Updating boot device parameters
[ 0.5436 ] tegrabct --bct P3448_A00_lpddr4_204Mhz_P987.bct --chip 0x21 0 --updatedevparam flash.xml.bin
[ 0.5462 ] Warning: No sdram params
[ 0.5468 ]
[ 0.5469 ] Updating bl info
[ 0.5497 ] tegrabct --bct P3448_A00_lpddr4_204Mhz_P987.bct --chip 0x21 0 --updateblinfo flash.xml.bin --updatesig images_list_signed.xml
[ 0.5549 ]
[ 0.5550 ] Updating secondary storage information into bct
[ 0.5579 ] tegraparser --pt flash.xml.bin --chip 0x21 0 --updatecustinfo P3448_A00_lpddr4_204Mhz_P987.bct
[ 0.5615 ]
[ 0.5616 ] Updating Odmdata
[ 0.5646 ] tegrabct --bct P3448_A00_lpddr4_204Mhz_P987.bct --chip 0x21 0 --updatefields Odmdata =0xa4000
[ 0.5671 ] Warning: No sdram params
[ 0.5677 ]
[ 0.5678 ] Get Signed section of bct
[ 0.5707 ] tegrabct --bct P3448_A00_lpddr4_204Mhz_P987.bct --chip 0x21 0 --listbct bct_list.xml
[ 0.5739 ]
[ 0.5740 ] Signing BCT
[ 0.5795 ] tegrasign --key None --list bct_list.xml --pubkeyhash pub_key.key
[ 0.5822 ] Assuming zero filled SBK key
[ 0.5833 ]
[ 0.5834 ] Updating BCT with signature
[ 0.5852 ] tegrabct --bct P3448_A00_lpddr4_204Mhz_P987.bct --chip 0x21 0 --updatesig bct_list_signed.xml
[ 0.6039 ]
[ 0.6040 ] Copying signatures
[ 0.6056 ] tegrahost --chip 0x21 0 --partitionlayout flash.xml.bin --updatesig images_list_signed.xml
[ 0.6144 ]
[ 0.6145 ] Updating BFS information on BCT
[ 0.6161 ] tegrabct --bct P3448_A00_lpddr4_204Mhz_P987.bct --chip 0x21 0 --updatebfsinfo flash.xml.bin
[ 0.6179 ]
[ 0.6180 ] Boot Rom communication
[ 0.6193 ] tegrarcm --chip 0x21 0 --rcm rcm_list_signed.xml
[ 0.6206 ] BR_CID: 0x4210100164441643080000000f008340
[ 0.6215 ] RCM version 0X210001
[ 0.6374 ] Boot Rom communication completed
[ 1.6456 ]
[ 1.6458 ] Sending BCTs
[ 1.6503 ] tegrarcm --download bct P3448_A00_lpddr4_204Mhz_P987.bct
[ 1.6539 ] Applet version 00.01.0000
[ 1.6712 ] Sending bct
[ 1.6713 ] [................................................] 100%
[ 1.8958 ]
[ 1.8978 ] tegrahost --chip 0x21 --align cboot.bin
[ 1.8999 ]
[ 1.9025 ] tegrahost --magicid EBT --appendsigheader cboot.bin cboot.bin_blheader
[ 1.9114 ]
[ 1.9533 ] tegrasign --key None --list cboot.bin_list.xml
[ 1.9560 ] Assuming zero filled SBK key
[ 2.0859 ]
[ 2.0906 ] tegrahost --updatesigheader cboot.bin_blheader.encrypt cboot.bin_blheader.hash zerosbk
[ 2.0970 ]
[ 2.1029 ] tegrahost --chip 0x21 --align tegra210-p3448-0000-p3449-0000-a02.dtb
[ 2.1070 ]
[ 2.1103 ] tegrahost --magicid DTB --appendsigheader tegra210-p3448-0000-p3449-0000-a02.dtb tegra210-p3448-0000-p3449-0000-a02.dtb_blheader
[ 2.1168 ]
[ 2.1210 ] tegrasign --key None --list tegra210-p3448-0000-p3449-0000-a02.dtb_list.xml
[ 2.1237 ] Assuming zero filled SBK key
[ 2.1453 ]
[ 2.1472 ] tegrahost --updatesigheader tegra210-p3448-0000-p3449-0000-a02.dtb_blheader.encrypt tegra210-p3448-0000-p3449-0000-a02.dtb_blheader.hash zerosbk
[ 2.1493 ]
[ 2.2757 ] Sending bootloader and pre-requisite binaries
[ 2.2794 ] tegrarcm --download ebt cboot.bin.encrypt 0 0 --download rp1 tegra210-p3448-0000-p3449-0000-a02.dtb.encrypt 0
[ 2.2825 ] Applet version 00.01.0000
[ 2.3045 ] Sending ebt
[ 2.3047 ] [................................................] 100%
[ 2.4105 ] Sending rp1
[ 2.4158 ] [................................................] 100%
[ 2.4759 ]
[ 2.4789 ] tegrarcm --boot recovery
[ 2.4813 ] Applet version 00.01.0000
[ 2.5011 ]
[ 2.5013 ] Retrieving storage infomation
[ 2.5042 ] tegrarcm --oem platformdetails storage storage_info.bin
[ 2.5067 ] Applet is not running on device. Continue with Bootloader
[ 3.1944 ]
[ 3.2403 ] tegradevflash --oem platformdetails storage storage_info.bin
[ 3.2430 ] Cboot version 00.01.0000
[ 3.2500 ] Saved platform info in storage_info.bin
[ 3.2515 ]
[ 3.2517 ] Flashing the device
[ 3.2546 ] tegradevflash --pt flash.xml.bin --storageinfo storage_info.bin --create
[ 3.2572 ] Cboot version 00.01.0000
[ 3.2606 ] Writing partition GPT with gpt.bin
[ 3.2613 ] [................................................] 100%
[ 3.2674 ] Writing partition PT with flash.xml.bin
[ 63.4994 ] [................................................] 100%
[ 63.5034 ] Writing partition NVC with nvtboot.bin.encrypt
[ 63.7545 ] [................................................] 100%
[ 63.7686 ] Writing partition NVC_R with nvtboot.bin.encrypt
[ 73.7882 ] [................................................] 100%
[ 73.8040 ] Writing partition TBC with nvtboot_cpu.bin.encrypt
[ 83.8309 ] [................................................] 100%
[ 83.8432 ] Writing partition RP1 with kernel_tegra210-p3448-0000-p3449-0000-a02.dtb.encrypt
[ 88.0148 ] [................................................] 100%
[ 88.0328 ] Writing partition EBT with cboot.bin.encrypt
[ 102.7020 ] [................................................] 100%
[ 102.7327 ] Writing partition WB0 with warmboot.bin.encrypt
[ 131.8057 ] [................................................] 100%
[ 131.8174 ] Writing partition BPF with sc7entry-firmware.bin.encrypt
[ 132.0814 ] [................................................] 100%
[ 132.0920 ] Writing partition TOS with tos-mon-only.img.encrypt
[ 132.3567 ] [................................................] 100%
[ 132.3691 ] Writing partition DTB with kernel_tegra210-p3448-0000-p3449-0000-a02.dtb.encrypt
[ 135.8069 ] [................................................] 100%
[ 135.8254 ] Writing partition LNX with boot.img.encrypt
[ 150.4933 ] [................................................] 100%
[ 150.5289 ] Warning: EKS partition magic header mismatch!
[ 190.1073 ] Writing partition EKS with eks.img
[ 190.1081 ] [................................................] 100%
[ 190.1176 ] Writing partition BMP with bmp.blob
[ 190.3808 ] [................................................] 100%
[ 190.4273 ] Writing partition RP4 with rp4.blob
[ 199.4796 ] [................................................] 100%
[ 199.4957 ] Writing partition VER_b with qspi_bootblob_ver.txt
[ 207.0833 ] [................................................] 100%
[ 207.1139 ] Writing partition VER with qspi_bootblob_ver.txt
[ 207.3781 ] [................................................] 100%
[ 207.3884 ] Writing partition APP with system.img
[ 207.6510 ] [................................................] 100%
[ 729.6374 ]
[ 729.6406 ] tegradevflash --write BCT P3448_A00_lpddr4_204Mhz_P987.bct
[ 729.6437 ] Cboot version 00.01.0000
[ 729.6466 ] Writing partition BCT with P3448_A00_lpddr4_204Mhz_P987.bct
[ 729.6479 ] [................................................] 100%
[ 736.3082 ]
[ 736.3083 ] Flashing completed
[ 736.3084 ] Coldbooting the device
[ 736.3099 ] tegradevflash --reboot coldboot
[ 736.3111 ] Cboot version 00.01.0000
[ 736.3137 ]
*** The target t210ref has been flashed successfully. ***
Reset the board to boot from internal eMMC.
I see some error in the flash.sh initial part boardinfo parsing which looks connected with detecting the SB/PKC configuration:
./tegraflash.py --chip 0x21 --applet "/l4t/Linux_for_Tegra/bootloader/nvtboot_recovery.bin" --skipuid --cmd "dump eeprom boardinfo cvm.bin"
/l4t/Linux_for_Tegra/bootloader/tegraflash_internal.py:1978: SyntaxWarning: "is not" with a literal. Did you mean "!="?
if sig_type is not "zerosbk":
/l4t/Linux_for_Tegra/bootloader/tegraflash_internal.py:1981: SyntaxWarning: "is" with a literal. Did you mean "=="?
if sig_type is "oem-rsa":
/l4t/Linux_for_Tegra/bootloader/tegraflash_internal.py:2416: SyntaxWarning: "is not" with a literal. Did you mean "!="?
while count is not 0 and not check_ismb2():
/l4t/Linux_for_Tegra/bootloader/tegraflash_internal.py:2425: SyntaxWarning: "is not" with a literal. Did you mean "!="?
while count is not 0:
Boardinfo from flash:
root@tchome:/l4t/Linux_for_Tegra# hexdump -C ./bootloader/cvm.bin
00000000 01 00 fc 00 78 0d 00 00 02 46 00 00 00 00 00 00 |....x....F......|
00000010 00 00 00 00 36 39 39 2d 31 33 34 34 38 2d 30 30 |....699-13448-00|
00000020 30 30 2d 32 30 30 20 46 2e 30 00 00 00 00 00 00 |00-200 F.0......|
00000030 00 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
00000040 ff ff ff ff 8e 1d e5 4b 04 00 31 34 32 31 39 31 |.......K..142191|
00000050 39 30 34 34 34 33 35 00 00 00 00 00 00 00 00 00 |9044435.........|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
00000090 00 00 00 00 00 00 4e 56 43 42 1c 00 4d 31 00 00 |......NVCB..M1..|
000000a0 ff ff ff ff ff ff ff ff ff ff ff ff 8e 1d e5 4b |...............K|
000000b0 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
000000c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
000000f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 9f |................|
00000100
Have in mind that I’ve tryed SB/PKC configuration which was not successful. Here is the Topic where I’ve shared my expirience on Jetson Nano devkit A02 SB/PKC capabilities which are not supported on devkit edvices and only supported on production module wth internal emmc):