# T4000 UART debug

**URL:** <https://forums.developer.nvidia.com/t/t4000-uart-debug/385530>\
**Category:** Jetson Thor\
**Tags:** uart, boot, board-design\
**Created:** [October 11, 2026, 7:09am UTC](https://forums.developer.nvidia.com/t/t4000-uart-debug/385530 "2026-10-11T07:09:29Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![jerry.wu3](https://developer.download.nvidia.com/images/forums/profile-default-devtalk-84.png) [@jerry.wu3](https://forums.developer.nvidia.com/u/jerry.wu3)\
**Post date:** [October 11, 2026, 7:09am UTC](https://forums.developer.nvidia.com/t/t4000-uart-debug/385530/1 "2026-10-11T07:09:29Z")

</div>

We are developing a T4000 carrier board but encountering a no-display issue via HDMI on boot. We cannot check the boot log because no UART pins are exposed on our board.

Could you please advise on the following:

1. Are there any alternative ways to debug the boot sequence?
2. Could you share the T4000 UART pin definitions so we can rework the board(pcba component not moudle pin out) to access the logs?

---

<div class="post-metadata">

**Author:** ![ShaneCCC](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/shaneccc/32/14043_2.png) [@ShaneCCC](https://forums.developer.nvidia.com/u/ShaneCCC)\
**Post date:** [October 11, 2026, 12:48pm UTC](https://forums.developer.nvidia.com/t/t4000-uart-debug/385530/4 "2026-10-11T12:48:24Z")

</div>

The Thor module’s debug signals are UART3\_TX\_DEBUG and UART3\_RX\_DEBUG, mapped internally to SoC UART0. The design guide lists the debug interface as 1.8 V, so use an adapter or  
level shifter compatible with that voltage. Connect module TX to adapter RX, module RX to adapter TX, and a common ground. Thor design guide, UART and debug sections (https://  
[developer.nvidia.com/downloads/assets/embedded/secure/jetson/thor/docs/jetson\_thor\_series\_modules\_designguide.pdf](http://developer.nvidia.com/downloads/assets/embedded/secure/jetson/thor/docs/jetson_thor_series_modules_designguide.pdf))

Once the UART connection is available, capture logs from power-on using the matching BSP’s demuxer:

cd Linux\_for\_Tegra/tools/demuxer  
mkdir -p /tmp/thor\_logs  
./nv\_tcu\_demuxer -m T264 -d /dev/ttyUSB0  
-r 115200 -s /tmp/thor\_logs -t

Replace /dev/ttyUSB0 with the actual adapter device. Thor UART documentation ([https://docs.nvidia.com/jetson/archives/r39.2.1/DeveloperGuide/AT/JetsonLinuxDevelopmentTools/](https://docs.nvidia.com/jetson/archives/r39.2.1/DeveloperGuide/AT/JetsonLinuxDevelopmentTools/)  
TegraCombinedUART.html)

---

<div class="post-metadata">

**Author:** ![system](https://sea2.discourse-cdn.com/nvidia/user_avatar/forums.developer.nvidia.com/system/32/68080_2.png) [@system](https://forums.developer.nvidia.com/u/system)\
**Post date:** [November 10, 2026, 1:16am UTC](https://forums.developer.nvidia.com/t/t4000-uart-debug/385530/6 "2026-11-10T01:16:07Z")

</div>

Closed on November 10, 2026, 1:16am UTC

This topic was automatically closed 14 days after the last reply. New replies are no longer allowed.
