[0000.126] [TegraBoot] (version 00.00.2018.01-l4t-33e7fa82) [0000.131] Processing in cold boot mode Bootloader 2 [0000.136] A02 Bootrom Patch rev = 1023 [0000.139] Power-up reason: pmc por [0000.142] No Battery Present [0000.145] pmic max77620 reset reason [0000.148] pmic max77620 NVERC : 0x40 [0000.152] RamCode = 0 [0000.154] Platform has DDR4 type RAM [0000.157] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x1727e5 [0000.173] Entering ramdump check [0000.176] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.189] Sdram initialization is successful [0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.217] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.223] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.257] Platform-DebugCarveout: 0 [0000.260] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.266] Non secure mode, and RB not enabled. [0000.272] Invalid GPT Partition [0000.287] Using BFS PT to query partitions [0000.291] failed to load NvTbootTbootCpu from (2:0) [0000.296] re-load NvTbootTbootCpu from (4:0) [0000.359] Csd NumOfBlocks=62423040 [0000.418] Using GPT Primary to query partitions [0000.427] Loading Tboot-CPU binary [0000.804] Verifying TBC in OdmNonSecureSBK mode [0000.814] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.821] Bootloader downloaded successfully. [0000.825] Downloaded Tboot-CPU binary to 0xa0000258 [0000.830] MAX77620_GPIO5 configured [0000.834] CPU power rail is up [0000.836] CPU clock enabled [0000.840] Performing RAM repair [0000.843] Updating A64 Warmreset Address to 0xa00002e9 [0000.848] Loading NvTbootBootloaderDTB [0002.160] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0002.225] Bootloader DTB Load Address: 0x83000000 [0002.230] Loading NvTbootKernelDTB [0003.541] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0003.606] Kernel DTB Load Address: 0x83100000 [0003.615] Loading cboot binary [0005.299] Verifying EBT in OdmNonSecureSBK mode [0005.341] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0005.348] Bootloader downloaded successfully. [0005.540] Using BFS PT to query partitions [0005.544] Next binary entry address: 0x92c00258 [0005.549] BoardId: 3448 [0005.553] Overriding pmu board id with proc board id [0005.558] Display board id is not available [0007.058] Verifying SC7EntryFw in OdmNonSecureSBK mode [0007.110] /bpmp deleted [0007.112] SC7EntryFw header found loaded at 0xff700000 [0007.301] OVR2 PMIC [0007.303] Bpmp FW successfully loaded [0007.319] WB0 init successfully at 0xff780000 [0007.323] Set NvDecSticky Bits [0007.327] GSC2 address ff53fffc value c0edbbcc [0007.333] GSC MC Settings done [0007.339] TOS Image length 53680 [0007.342] Monitor size 53680 [0007.345] OS size 0 [0007.506] Secure Os AES-CMAC Verification Success! [0007.510] TOS image cipher info: plaintext [0007.514] Loading and Validation of Secure OS Successful [0007.530] SC7 Entry Firmware - 0xff700000, 0x4000 [0007.535] NvTbootPackSdramParams: start. [0007.540] NvTbootPackSdramParams: done. [0007.544] Tegraboot started after 53293 us [0007.548] Basic modules init took 5643187 us [0007.552] NvTbootQspiFlashIoctl: Opcode = 1 not supported [0007.557] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB [0007.562] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0007.568] Storage Device Read Time = 6744 ms, Read Size = 2306 KB [0007.574] Storage Device Write Time = 0 ms, Write Size = 0 KB [0007.579] Next stage binary read took 1531007 us [0007.584] Carveout took -1542688 us [0007.587] CPU initialization took 2040444 us [0007.591] Total time taken by TegraBoot 7671950 us [0007.596] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):23b153a63 NOTICE: BL31: Built : 22:39:57, Dec 9 2019 ERROR: Error initializing runtime service trusty_fast [0007.718] RamCode = 0 [0007.723] LPDDR4 Training: Read DT: Number of tables = 2 [0007.728] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0007.741] EMC Training Successful [0007.744] 408000 not found in DVFS table [0007.750] RamCode = 0 [0007.754] DT Write: emc-table@204000 succeeded [0007.759] DT Write: emc-table@1600000 succeeded [0007.763] LPDDR4 Training: Write DT: Number of tables = 2 [0007.959] [0007.960] Debug Init done [0007.963] Marked DTB cacheable [0007.966] Bootloader DTB loaded at 0x83000000 [0007.970] Marked DTB cacheable [0007.973] Kernel DTB loaded at 0x83100000 [0007.977] DeviceTree Init done [0007.993] Pinmux applied successfully [0007.997] gicd_base: 0x50041000 [0008.000] gicc_base: 0x50042000 [0008.003] Interrupts Init done [0008.008] Using base:0x60005090 & irq:208 for tick-timer [0008.013] Using base:0x60005098 for delay-timer [0008.017] platform_init_timer: DONE [0008.021] Timer(tick) Init done [0008.025] osc freq = 38400 khz [0008.029] [0008.030] Welcome to L4T Cboot [0008.033] [0008.034] Cboot Version: 00.00.2018.01-t210-40c3ff9c [0008.039] calling constructors [0008.042] initializing heap [0008.044] initializing threads [0008.047] initializing timers [0008.050] creating bootstrap completion thread [0008.055] top of bootstrap2() [0008.058] CPU: ARM Cortex A57 [0008.060] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0008.065] initializing platform [0008.073] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0008.077] ID LSB = 0x36, ID-CFI len = 194 bytes [0008.082] Macronix QSPI chip present [0008.085] SPI device register [0008.088] init boot device [0008.091] allocating memory for boot device(SPI) [0008.095] registering boot device [0008.105] sdmmc node status = okay [0008.108] sdcard instance = 0 [0008.111] sdcard gpio handle 0x56 [0008.114] sdcard gpio pin 0xc9 [0008.117] sdcard gpio flags 0x0 [0008.120] vmmc-supply 0x99 [0008.123] Instance: 0 [0008.125] Allocating memory for context [0008.128] enabling clock [0008.131] sd card init [0008.133] Check card present and stable [0008.137] Send command 0 [0008.153] Send command 3 [0008.158] Set RCA for the card [0008.161] Query card specific data by command 9 [0008.167] Parse CSD data [0008.169] Send command 7 [0008.180] Calling sd device register [0008.183] Init sdcard [0008.185] Allocating memory for boot device [0008.190] Registering user device [0008.203] Enable APE clock [0008.205] Un-powergate APE partition [0008.209] of_register: registering tegra_udc to of_hal [0008.214] of_register: registering inv20628-driver to of_hal [0008.220] of_register: registering ads1015-driver to of_hal [0008.225] of_register: registering lp8557-bl-driver to of_hal [0008.231] of_register: registering bq2419x_charger to of_hal [0008.236] of_register: registering bq27441_fuel_gauge to of_hal [0008.248] gpio framework initialized [0008.251] of_register: registering tca9539_gpio to of_hal [0008.257] of_register: registering tca9539_gpio to of_hal [0008.262] of_register: registering i2c_bus_driver to of_hal [0008.268] of_register: registering i2c_bus_driver to of_hal [0008.273] of_register: registering i2c_bus_driver to of_hal [0008.279] pmic framework initialized [0008.282] of_register: registering max77620_pmic to of_hal [0008.288] regulator framework initialized [0008.292] of_register: registering tps65132_bl_driver to of_hal [0008.298] initializing target [0008.303] gpio_driver_register: register 'tegra_gpio_driver' driver [0008.312] board ID = D78, board SKU = 0 [0008.315] Skipping Z3! [0008.320] fixed regulator driver initialized [0008.338] initializing OF layer [0008.340] NCK carveout not present [0008.344] Skipping dts_overrides [0008.348] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.365] I2C Bus Init done [0008.367] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.378] I2C Bus Init done [0008.380] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.391] I2C Bus Init done [0008.393] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.404] I2C Bus Init done [0008.406] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.417] I2C Bus Init done [0008.419] of_children_init: Ops found for compatible string maxim,max77620 [0008.430] max77620_init using irq 118 [0008.435] register 'maxim,max77620' pmic [0008.439] gpio_driver_register: register 'max77620-gpio' driver [0008.445] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.456] I2C Bus Init done [0008.459] NCK carveout not present [0008.469] Find /i2c@7000c000's alias i2c0 [0008.473] get eeprom at 1-a0, size 256, type 0 [0008.482] Find /i2c@7000c500's alias i2c2 [0008.486] get eeprom at 3-a0, size 256, type 0 [0008.490] get eeprom at 3-ae, size 256, type 0 [0008.494] pm_ids_update: Updating 1,a0, size 256, type 0 [0008.500] I2C slave not started [0008.503] I2C write failed [0008.505] Writing offset failed [0008.508] eeprom_init: EEPROM read failed [0008.512] pm_ids_update: eeprom init failed [0008.516] pm_ids_update: Updating 3,a0, size 256, type 0 [0008.547] pm_ids_update: The pm board id is 3448-0000-200 [0008.553] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0008.561] pm_ids_update: pm id update successful [0008.566] pm_ids_update: Updating 3,ae, size 256, type 0 [0008.596] pm_ids_update: The pm board id is 3449-0000-200 [0008.602] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0008.610] pm_ids_update: pm id update successful [0008.641] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0008.647] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0008.655] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0008.661] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0008.669] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:53:41 [0008.676] Plugin Manager: Parse ODM data 0x00084000 [0008.686] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 [0008.708] Find /i2c@7000c000's alias i2c0 [0008.711] get eeprom at 1-a0, size 256, type 0 [0008.720] Find /i2c@7000c500's alias i2c2 [0008.724] get eeprom at 3-a0, size 256, type 0 [0008.729] get eeprom at 3-ae, size 256, type 0 [0008.733] pm_ids_update: Updating 1,a0, size 256, type 0 [0008.738] I2C slave not started [0008.741] I2C write failed [0008.744] Writing offset failed [0008.747] eeprom_init: EEPROM read failed [0008.751] pm_ids_update: eeprom init failed [0008.755] pm_ids_update: Updating 3,a0, size 256, type 0 [0008.785] pm_ids_update: The pm board id is 3448-0000-200 [0008.792] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0008.799] pm_ids_update: pm id update successful [0008.803] pm_ids_update: Updating 3,ae, size 256, type 0 [0008.833] pm_ids_update: The pm board id is 3449-0000-200 [0008.840] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0008.847] pm_ids_update: pm id update successful [0008.877] Add serial number:1422419088143 as DT property [0008.885] Applying platform configs [0008.892] platform-init is not present. Skipping [0008.896] calling apps_init() [0008.921] Found 14 GPT partitions in "sd0" [0008.925] Proceeding to Cold Boot [0008.929] starting app android_boot_app [0008.932] Device state: unlocked [0008.936] display console init [0008.944] could not find regulator [0008.947] hdmi cable connected [0008.963] edid read success [0008.978] edid read succDT entry for leds-pwm not found e[0008.987] ss [0008.988] width = 640, height = 480, frequency = 25174825 [0008.993] width = 640, height = 480, frequency = 25174825 [0008.999] width = 640, height = 480, frequency = 25174825 [0009.004] width = 640, height = 480, frequency = 25174825 [0009.009] width = 1920, height = 1080, frequency = 148500000 [0009.015] width = 720, height = 480, frequency = 27000000 [0009.020] width = 1280, height = 720, frequency = 74250000 [0009.026] width = 1280, height = 720, frequency = 74175824 [0009.031] width = 720, height = 480, frequency = 26973026 [0009.037] width = 640, height = 480, frequency = 25174825 [0009.042] width = 720, height = 576, frequency = 26973026 [0009.047] width = 1280, height = 720, frequency = 74175824 [0009.053] width = 1920, height = 1080, frequency = 148351648 [0009.059] width = 1920, height = 1080, frequency = 148351648 [0009.064] Best mode Width = 1920, Height = 1080, freq = 148351648 [0009.072] tmds-config node not found [0009.076] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-s [0009.091] setting 'vdd-1v8' regulator to 1800000 micro volts [0009.098] could not find regulator [0009.102] could not find regulator [0009.105] could not find regulator [0009.133] using default cmu settings [0009.137] dc_hdmi_enable, starting HDMI initialisation [0009.143] dc_hdmi_enable, HDMI initialisation complete [0009.148] list and configure display window [0009.157] display console init completed [0009.168] subnode volume_up is not found ! [0009.172] subnode back is not found ! [0009.176] subnode volume_down is not found ! [0009.180] subnode menu is not found ! [0009.183] Gpio keyboard init success [0009.227] found decompressor handler: lz4-legacy [0009.242] decompressing blob (type 1)... [0009.277] load_bmp_blob: panelresolution=1080 type=3 [0009.328] decompressor handler not found [0009.331] load_firmware_blob: Firmware blob loaded, entries=2 [0009.337] -------> se_aes_verify_sbk_clear: 747 [0009.342] se_aes_verify_sbk_clear: Error [0009.345] bl_battery_charging: connected to external power supply [0009.353] xusb is supported [0009.359] error while finding nvidia,portmap [0009.863] xusb blob version 0 size 124416 [0009.867] firmware size 124416 [0009.872] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0009.880] xhci0: 64 bytes context size, 32-bit DMA [0009.920] usbus0: 5.0Gbps Super Speed USB v3.0 [0009.940] uhub0: on usbus0 [0010.590] uhub0: 9 ports with 9 removable, self powered [0011.590] failed to get HID devices [0011.594] failed to init xhci or no usb device attached [0011.604] device_query_partition_size: failed to open partition sd0:MSC ! [0011.611] MSC Partition not found [0011.617] device_query_partition_size: failed to open partition sd0:USP ! [0011.624] USP partition read failed! [0011.627] blob_init: blob-partition USP header read failed [0011.633] android_boot Unable to update recovery partition [0011.638] kfs_getpartname: name = LNX [0011.642] Loading kernel from LNX [0011.740] load kernel from storage [0011.752] decompressor handler not found [0011.809] Successfully loaded kernel and ramdisk images [0011.816] load_bmp_blob: panelresolution=1080 type=3 [0012.312] display bmp image done [0012.315] NCK carveout not present [0012.318] Skipping dts_overrides [0012.321] NCK carveout not present [0012.331] Find /i2c@7000c000's alias i2c0 [0012.335] get eeprom at 1-a0, size 256, type 0 [0012.344] Find /i2c@7000c500's alias i2c2 [0012.348] get eeprom at 3-a0, size 256, type 0 [0012.352] get eeprom at 3-ae, size 256, type 0 [0012.357] pm_ids_update: Updating 1,a0, size 256, type 0 [0012.362] I2C slave not started [0012.365] I2C write failed [0012.368] Writing offset failed [0012.371] eeprom_init: EEPROM read failed [0012.375] pm_ids_update: eeprom init failed [0012.379] pm_ids_update: Updating 3,a0, size 256, type 0 [0012.409] pm_ids_update: The pm board id is 3448-0000-200 [0012.416] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0012.424] pm_ids_update: pm id update successful [0012.428] pm_ids_update: Updating 3,ae, size 256, type 0 [0012.458] pm_ids_update: The pm board id is 3449-0000-200 [0012.465] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0012.473] pm_ids_update: pm id update successful [0012.503] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0012.509] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0012.517] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0012.523] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0012.532] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:53:41 [0012.538] Plugin Manager: Parse ODM data 0x00084000 [0012.549] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 [0012.563] Add serial number:1422419088143 as DT property [0012.572] "bpmp" doesn't exist, creating [0012.578] Updated bpmp info to DTB [0012.583] Updated initrd info to DTB [0012.586] "proc-board" doesn't exist, creating [0012.592] Updated board info to DTB [0012.595] "pmu-board" doesn't exist, creating [0012.601] Updated board info to DTB [0012.604] "display-board" doesn't exist, creating [0012.610] Updated board info to DTB [0012.613] "reset" doesn't exist, creating [0012.618] Updated reset info to DTB [0012.621] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_po [0012.660] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 cons [0012.672] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200 [0012.685] Updated bootarg info to DTB [0012.689] Adding uuid 00000001644495821c00000011fd8280 to DT [0012.695] Adding eks info 0 to DT [0012.700] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0012.706] Updated memory info to DTB [0012.712] Updated system-lp0-disable info to DTB [0012.720] set vdd_core voltage to 1075 mv [0012.724] setting 'vdd-core' regulator to 1075000 micro volts [0012.740] Found secure-pmc; disable BPMP U-Boot 2016.07-g0536cf2a27 (Dec 09 2019 - 22:40:32 -0800) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 733 bytes read in 179 ms (3.9 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 5487751 bytes read in 518 ms (10.1 MiB/s) Retrieving file: /boot/Image 34191368 bytes read in 2935 ms (11.1 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_inft ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 00000000831776f0 Starting kernel ... [ 1.096115] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.262720] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.262748] imx219 6-0010: board setup failed