[0015.079] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses.
[0015.087] I> MB1 (prd-version: 1.5.1.3-t194-41334769-d2a21c57)
[0015.093] I> Boot-mode: Platform RCM
[0015.096] I> Chip revision : A02P
[0015.099] I> Bootrom patch version : 15 (correctly patched)
[0015.104] I> ATE fuse revision : 0x200
[0015.108] I> Ram repair fuse : 0x0
[0015.111] I> Ram Code : 0x0
[0015.113] I> rst_source : 0x0
[0015.116] I> rst_level : 0x0
[0015.120] I> USB configuration success
[0017.849] I> mb2 image downloaded
[0018.128] I> Recovery boot mode 0
[0018.131] I> Boot-device: QSPI
[0018.136] I> UPHY full init done
[0018.140] I> MB1 done

[0018.145] W> Profiler not initialized
[0018.149] I> Welcome to MB2(TBoot-BPMP) Applet (version: 00.00.2018.32-mobile-9af8dd5a)
[0018.157] W> Profiler not initialized
[0018.160] I> DMA Heap @ [0x40020000 - 0x40065800]
[0018.165] I> Default Heap @ [0xd486400 - 0xd48a400]
[0018.170] W> Profiler not initialized
[0018.173] W> Profiler not initialized
[0018.177] E> DEVICE_PROD: Invalid value data = 0, size = 0.
[0018.182] W> device prod register failed
[0018.186] W> Profiler not initialized
[0018.190] E> Error in command_complete 18000 int_status
[0018.195] E> OCR failed, error = f0f0706
[0018.199] I> SDMMC is not present.
[0018.203] I> QSPI Flash Size = 32 MB
[0018.214] I> Qspi initialized successfully
[0018.265] E> Link startup dme_set failed
[0018.269] E> UFS initialization failed
[0018.272] I> UFS is not present
[0018.275] W> Profiler not initialized
[0018.281] I> Found 47 partitions in QSPI_FLASH (instance 0)
[0018.286] W> Profiler not initialized
[0018.289] W> Profiler not initialized
[0018.293] W> Profiler not initialized
[0018.297] I> Entering 3p server
[0018.300] I> USB configuration success
[0020.191] I> Populate eeprom info
[0020.196] I> Populate eeprom info for module cvm
[0020.794] I> Rebooting : reboot-recovery


[002��
[0002.337] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses.
[0002.345] I> MB1 (prd-version: 1.5.1.3-t194-41334769-d2a21c57)
[0002.351] I> Boot-mode: RCM
[0002.353] I> Chip revision : A02P
[0002.356] I> Bootrom patch version : 15 (correctly patched)
[0002.362] I> ATE fuse revision : 0x200
[0002.365] I> Ram repair fuse : 0x0
[0002.368] I> Ram Code : 0x0
[0002.371] I> rst_source : 0xb
[0002.373] I> rst_level : 0x1
[0002.377] I> USB configuration success
[0004.798] I> Handling oem command 6
[0004.801] E> NV3P_SERVER: Fuse burn is not supported.
[0005.665] I> bct_bootrom image downloaded
[0005.673] C> LOADER: mb1bct binary ratchet level 0 is less than ratchet level 60 from HW fuses.
[0005.682] C> LOADER: Could not read mb1bct.
[0005.686] C> Fail to load mb1-bct bin
[0005.689] C> OEM authentication of MB1-BCT failed!!!
[0005.694] E> NV3P_SERVER: Failed to verify image bct_mb1.