[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x506e4 [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.178] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.198] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.233] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.280] Initialize FailControl [0000.283] Read PT from (2:0) [0000.314] PT crc32 and magic check passed. [0000.318] Using BFS PT to query partitions [0000.323] Loading Tboot-CPU binary [0000.352] Verifying TBC in OdmNonSecureSBK mode [0000.362] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.369] Bootloader downloaded successfully. [0000.373] Downloaded Tboot-CPU binary to 0xa0000258 [0000.378] MAX77620_GPIO5 configured [0000.381] CPU power rail is up [0000.384] CPU clock enabled [0000.388] Performing RAM repair [0000.391] Updating A64 Warmreset Address to 0xa00002e9 [0000.396] BoardID = 3448, SKU = 0x0 [0000.399] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.403] Nano-SD: checking PT table on QSPI ... [0000.407] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.413] Loading NvTbootBootloaderDTB [0000.480] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.551] Bootloader DTB Load Address: 0x83000000 [0000.556] BoardID = 3448, SKU = 0x0 [0000.559] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.563] Nano-SD: checking PT table on QSPI ... [0000.567] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.573] Loading NvTbootKernelDTB [0000.639] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.711] Kernel DTB Load Address: 0x83100000 [0000.715] BoardID = 3448, SKU = 0x0 [0000.718] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.722] Nano-SD: checking PT table on QSPI ... [0000.726] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.734] Loading cboot binary [0000.850] Verifying EBT in OdmNonSecureSBK mode [0000.892] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.899] Bootloader downloaded successfully. [0000.903] BoardID = 3448, SKU = 0x0 [0000.906] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.910] Nano-SD: checking PT table on QSPI ... [0000.914] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.920] PT: Partition NCT NOT found ! [0000.924] Warning: Find Partition via PT Failed [0000.928] Next binary entry address: 0x92c00258 [0000.933] BoardId: 3448 [0000.938] Overriding pmu board id with proc board id [0000.942] Display board id is not available [0000.947] BoardID = 3448, SKU = 0x0 [0000.950] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.954] Nano-SD: checking PT table on QSPI ... [0000.958] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.065] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.121] /bpmp deleted [0001.123] SC7EntryFw header found loaded at 0xff700000 [0001.311] OVR2 PMIC [0001.312] Bpmp FW successfully loaded [0001.316] BoardID = 3448, SKU = 0x0 [0001.319] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.323] Nano-SD: checking PT table on QSPI ... [0001.327] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.334] WB0 init successfully at 0xff780000 [0001.339] Verifying NvTbootWb0 in OdmNonSecureSBK mode [0001.344] Set NvDecSticky Bits [0001.347] GSC2 address ff53fffc value c0edbbcc [0001.353] GSC MC Settings done [0001.356] BoardID = 3448, SKU = 0x0 [0001.360] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.363] Nano-SD: checking PT table on QSPI ... [0001.368] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.375] TOS Image length 53680 [0001.378] Monitor size 53680 [0001.381] OS size 0 [0001.396] Secure Os AES-CMAC Verification Success! [0001.400] TOS image cipher info: plaintext [0001.404] Loading and Validation of Secure OS Successful [0001.420] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.425] NvTbootPackSdramParams: start. [0001.430] NvTbootPackSdramParams: done. [0001.434] Tegraboot started after 51866 us [0001.438] Basic modules init took 935909 us [0001.442] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.447] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.453] Next stage binary read took 102859 us [0001.457] Carveout took -132464 us [0001.460] CPU initialization took 510370 us [0001.464] Total time taken by TegraBoot 1416674 us [0001.469] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:09:37, Jul 26 2021 ERROR: Error initializing runtime service trusty_fast [0001.591] RamCode = 0 [0001.596] LPDDR4 Training: Read DT: Number of tables = 2 [0001.601] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.614] EMC Training Successful [0001.617] 408000 not found in DVFS table [0001.623] RamCode = 0 [0001.626] DT Write: emc-table@204000 succeeded [0001.632] DT Write: emc-table@1600000 succeeded [0001.636] LPDDR4 Training: Write DT: Number of tables = 2 [0001.684] [0001.685] Debug Init done [0001.688] Marked DTB cacheable [0001.691] Bootloader DTB loaded at 0x83000000 [0001.696] Marked DTB cacheable [0001.699] Kernel DTB loaded at 0x83100000 [0001.702] DeviceTree Init done [0001.715] Pinmux applied successfully [0001.720] gicd_base: 0x50041000 [0001.723] gicc_base: 0x50042000 [0001.726] Interrupts Init done [0001.730] Using base:0x60005090 & irq:208 for tick-timer [0001.736] Using base:0x60005098 for delay-timer [0001.740] platform_init_timer: DONE [0001.743] Timer(tick) Init done [0001.747] osc freq = 38400 khz [0001.751] [0001.752] Welcome to L4T Cboot [0001.755] [0001.756] Cboot Version: 00.00.2018.01-t210-c952b4e6 [0001.761] calling constructors [0001.764] initializing heap [0001.767] initializing threads [0001.770] initializing timers [0001.773] creating bootstrap completion thread [0001.777] top of bootstrap2() [0001.780] CPU: ARM Cortex A57 [0001.783] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.788] initializing platform [0001.795] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.799] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.804] Macronix QSPI chip present [0001.807] SPI device register [0001.810] init boot device [0001.813] allocating memory for boot device(SPI) [0001.817] registering boot device [0001.826] QSPI bdev is already initialized [0001.830] Enable APE clock [0001.832] Un-powergate APE partition [0001.836] of_register: registering tegra_udc to of_hal [0001.841] of_register: registering inv20628-driver to of_hal [0001.847] of_register: registering ads1015-driver to of_hal [0001.852] of_register: registering lp8557-bl-driver to of_hal [0001.858] of_register: registering bq2419x_charger to of_hal [0001.863] of_register: registering bq27441_fuel_gauge to of_hal [0001.875] gpio framework initialized [0001.878] of_register: registering tca9539_gpio to of_hal [0001.884] of_register: registering tca9539_gpio to of_hal [0001.889] of_register: registering i2c_bus_driver to of_hal [0001.894] of_register: registering i2c_bus_driver to of_hal [0001.900] of_register: registering i2c_bus_driver to of_hal [0001.906] pmic framework initialized [0001.909] of_register: registering max77620_pmic to of_hal [0001.915] regulator framework initialized [0001.918] of_register: registering tps65132_bl_driver to of_hal [0001.924] initializing target [0001.930] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.938] board ID = D78, board SKU = 0 [0001.942] Skipping Z3! [0001.947] fixed regulator driver initialized [0001.964] initializing OF layer [0001.967] NCK carveout not present [0001.970] Skipping dts_overrides [0001.974] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.991] I2C Bus Init done [0001.993] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.004] I2C Bus Init done [0002.006] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.016] I2C Bus Init done [0002.019] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.029] I2C Bus Init done [0002.032] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.042] I2C Bus Init done [0002.045] of_children_init: Ops found for compatible string maxim,max77620 [0002.055] max77620_init using irq 118 [0002.060] register 'maxim,max77620' pmic [0002.064] gpio_driver_register: register 'max77620-gpio' driver [0002.070] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.081] I2C Bus Init done [0002.084] NCK carveout not present [0002.094] Find /i2c@7000c000's alias i2c0 [0002.098] get eeprom at 1-a0, size 256, type 0 [0002.106] Find /i2c@7000c500's alias i2c2 [0002.110] get eeprom at 3-a0, size 256, type 0 [0002.114] get eeprom at 3-ae, size 256, type 0 [0002.119] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.124] I2C slave not started [0002.127] I2C write failed [0002.130] Writing offset failed [0002.133] eeprom_init: EEPROM read failed [0002.137] pm_ids_update: eeprom init failed [0002.141] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.171] pm_ids_update: The pm board id is 3448-0000-400 [0002.178] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.186] pm_ids_update: pm id update successful [0002.191] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.221] pm_ids_update: The pm board id is 3449-0000-400 [0002.227] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.235] pm_ids_update: pm id update successful [0002.265] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.271] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.279] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.285] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.293] updating /chosen/nvidia,ethernet-mac node 00:04:4b:eb:d0:e3 [0002.299] Plugin Manager: Parse ODM data 0x000a4000 [0002.312] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.326] Find /i2c@7000c000's alias i2c0 [0002.330] get eeprom at 1-a0, size 256, type 0 [0002.339] Find /i2c@7000c500's alias i2c2 [0002.342] get eeprom at 3-a0, size 256, type 0 [0002.347] get eeprom at 3-ae, size 256, type 0 [0002.351] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.357] I2C slave not started [0002.360] I2C write failed [0002.362] Writing offset failed [0002.365] eeprom_init: EEPROM read failed [0002.369] pm_ids_update: eeprom init failed [0002.373] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.403] pm_ids_update: The pm board id is 3448-0000-400 [0002.410] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.416] pm_ids_update: pm id update successful [0002.421] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.451] pm_ids_update: The pm board id is 3449-0000-400 [0002.457] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.464] pm_ids_update: pm id update successful [0002.495] Add serial number:1422919167844 as DT property [0002.502] Applying platform configs [0002.509] platform-init is not present. Skipping [0002.513] calling apps_init() [0002.519] Couldn't find GPT header [0002.524] Proceeding to Cold Boot [0002.527] starting app android_boot_app [0002.531] Device state: unlocked [0002.534] display console init [0002.542] could not find regulator [0002.545] hdmi cable connected [0002.561] edid read success [0002.576] DT entry for leds-pwm not found [0002.580] edid read success [0002.582] width = 640, height = 480, frequency = 25174825 [0002.588] width = 640, height = 480, frequency = 25174825 [0002.593] width = 640, height = 480, frequency = 25174825 [0002.599] width = 1024, height = 600, frequency = 49000000 [0002.604] width = 720, height = 576, frequency = 27000000 [0002.609] width = 720, height = 480, frequency = 26973026 [0002.615] width = 720, height = 480, frequency = 26973026 [0002.620] width = 720, height = 576, frequency = 26973026 [0002.626] width = 720, height = 576, frequency = 26973026 [0002.631] width = 1280, height = 720, frequency = 74175824 [0002.636] width = 1280, height = 720, frequency = 74175824 [0002.642] width = 1920, height = 1080, frequency = 148351648 [0002.647] width = 1920, height = 1080, frequency = 148351648 [0002.653] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.661] tmds-config node not found [0002.665] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.680] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.687] could not find regulator [0002.690] could not find regulator [0002.694] could not find regulator [0002.722] using default cmu settings [0002.726] dc_hdmi_enable, starting HDMI initialisation [0002.732] dc_hdmi_enable, HDMI initialisation complete [0002.737] list and configure display window [0002.746] display console init completed [0002.757] subnode volume_up is not found ! [0002.761] subnode back is not found ! [0002.764] subnode volume_down is not found ! [0002.768] subnode menu is not found ! [0002.772] Gpio keyboard init success [0002.839] found decompressor handler: lz4-legacy [0002.853] decompressing blob (type 1)... [0002.894] load_bmp_blob: panelresolution=1080 type=3 [0002.970] decompressor handler not found [0002.973] load_firmware_blob: Firmware blob loaded, entries=2 [0002.979] XUSB blob version 0 size 126464 @ 0x9b4c928c [0002.985] -------> se_aes_verify_sbk_clear: 747 [0002.990] se_aes_verify_sbk_clear: Error [0002.993] SE operation failed [0002.996] bl_battery_charging: connected to external power supply [0003.008] device_query_partition_size: failed to open partition spiflash0:MSC ! [0003.016] MSC Partition not found [0003.022] device_query_partition_size: failed to open partition spiflash0:USP ! [0003.029] USP partition read failed! [0003.033] blob_init: blob-partition USP header read failed [0003.038] android_boot Unable to update recovery partition [0003.044] kfs_getpartname: name = LNX [0003.047] Loading kernel from LNX [0003.056] Found 19 BFS partitions in "spiflash0" [0003.378] load kernel from storage [0003.383] decompressor handler not found [0003.649] Successfully loaded kernel and ramdisk images [0003.655] board ID = D78, board SKU = 0 [0003.659] sdmmc node status = okay [0003.663] sdcard instance = 0 [0003.665] sdmmc cd-inverted [0003.668] sdcard gpio handle 0x5b [0003.671] sdcard gpio pin 0xc9 [0003.674] sdcard gpio flags 0x0 [0003.677] vmmc-supply 0x9d [0003.680] cd_gpio_pin = 201 [0003.683] pin_state = 0 [0003.685] Found sdcard [0003.687] SD-card IS present ... [0003.690] load_and_boot_kernel: SD card detected OK [0003.696] load_bmp_blob: panelresolution=1080 type=3 [0004.191] display bmp image done [0004.194] NCK carveout not present [0004.197] Skipping dts_overrides [0004.200] NCK carveout not present [0004.210] Find /i2c@7000c000's alias i2c0 [0004.214] get eeprom at 1-a0, size 256, type 0 [0004.222] Find /i2c@7000c500's alias i2c2 [0004.226] get eeprom at 3-a0, size 256, type 0 [0004.230] get eeprom at 3-ae, size 256, type 0 [0004.235] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.240] I2C slave not started [0004.243] I2C write failed [0004.246] Writing offset failed [0004.249] eeprom_init: EEPROM read failed [0004.253] pm_ids_update: eeprom init failed [0004.257] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.287] pm_ids_update: The pm board id is 3448-0000-400 [0004.294] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0004.302] pm_ids_update: pm id update successful [0004.307] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.337] pm_ids_update: The pm board id is 3449-0000-400 [0004.343] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0004.351] pm_ids_update: pm id update successful [0004.381] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.387] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0004.395] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.401] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0004.409] updating /chosen/nvidia,ethernet-mac node 00:04:4b:eb:d0:e3 [0004.415] Plugin Manager: Parse ODM data 0x000a4000 [0004.428] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0004.436] Add serial number:1422919167844 as DT property [0004.445] "bpmp" doesn't exist, creating [0004.450] Updated bpmp info to DTB [0004.455] Updated initrd info to DTB [0004.459] "proc-board" doesn't exist, creating [0004.465] Updated board info to DTB [0004.468] "pmu-board" doesn't exist, creating [0004.474] Updated board info to DTB [0004.477] "display-board" doesn't exist, creating [0004.483] Updated board info to DTB [0004.487] "reset" doesn't exist, creating [0004.491] Updated reset info to DTB [0004.495] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 [0004.534] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.540] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0004.553] Updated bootarg info to DTB [0004.556] Adding uuid 00000001644577851c00000003028240 to DT [0004.562] Adding eks info 0 to DT [0004.568] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.574] Updated memory info to DTB [0004.581] set vdd_core voltage to 1075 mv [0004.585] setting 'vdd-core' regulator to 1075000 micro volts [0004.591] Found secure-pmc; disable BPMP U-Boot 2020.04-g46e4604c78 (Jul 26 2021 - 12:09:42 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 845 bytes read in 28 ms (29.3 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7160133 bytes read in 329 ms (20.8 MiB/s) Retrieving file: /boot/Image 34484232 bytes read in 1521 ms (21.6 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317ce2a copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-tegra (buildbrain@mobile-u64-5496-d5000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Mon Jul 26 12:13:06 PDT 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.164191] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.319356] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.319429] imx219 7-0010: board setup failed [ 1.343261] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.343320] imx219 8-0010: board setup failed [ 2.026785] cgroup: cgroup2: unknown option "nsdelegate" [ 3.594095] random: crng init done [ 3.597526] random: 7 urandom warning(s) missed due to ratelimiting [ 3.879532] using random self ethernet address [ 3.892099] using random host ethernet address [ 4.694208] using random self ethernet address [ 4.699298] using random host ethernet address [ 9.310736] Bridge firewalling registered Ubuntu 18.04.5 LTS fisys-desktop ttyS0