[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-tegra (buildbrain@mobile-u64-5496-d5000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Mon Jul 26 12:13:06 PDT 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] On node 0 totalpages: 1039872 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 519168 pages, LIFO batch:31 [ 0.000000] Normal zone: 8136 pages used for memmap [ 0.000000] Normal zone: 520704 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57624 r8192 d32488 u98304 [ 0.000000] pcpu-alloc: s57624 r8192 d32488 u98304 alloc=24*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29760(90%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3560280K/4159488K available (15358K kernel code, 2956K rwdata, 6692K rodata, 8640K init, 612K bss, 124072K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f80000 ( 15360 KB) [ 0.000000] .rodata : 0xffffff8008f80000 - 0xffffff8009610000 ( 6720 KB) [ 0.000000] .init : 0xffffff8009610000 - 0xffffff8009e80000 ( 8640 KB) [ 0.000000] .data : 0xffffff8009e80000 - 0xffffff800a163008 ( 2957 KB) [ 0.000000] .bss : 0xffffff800a163008 - 0xffffff800a1fc0b4 ( 613 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.001695] Console: colour dummy device 80x25 [ 0.001706] console [tty0] enabled [ 0.001712] bootconsole [uart8250] disabled [ 0.001734] kmemleak: Kernel memory leak detector disabled [ 0.001751] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.001765] pid_max: default: 32768 minimum: 301 [ 0.002216] Security Framework initialized [ 0.002440] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.002449] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003599] ftrace: allocating 47077 entries in 184 pages [ 0.172670] sched-energy: CPU device node has no sched-energy-costs [ 0.172704] ASID allocator initialised with 65536 entries [ 0.211891] tegra-id: chipid=22117. [ 0.211905] tegra-id: opt_subrevision=0. [ 0.211922] Tegra Speedo/IDDQ fuse revision 4 [ 0.211927] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.211933] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0 [ 0.211939] Tegra: CPU Speedo Value 2063, SoC Speedo Value 1969, GPU Speedo Value 2090 [ 0.211943] Tegra: CPU IDDQ Value 1920, SoC IDDQ Value 2308, GPU IDDQ Value 2980 [ 0.211962] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1 [ 0.211977] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.211984] DTB Build time: Jul 26 2021 12:16:29 [ 0.261102] CPU1: Booted secondary processor [411fd071] [ 0.293007] CPU2: Booted secondary processor [411fd071] [ 0.324975] CPU3: Booted secondary processor [411fd071] [ 0.325063] Brought up 4 CPUs [ 0.325067] SMP: Total of 4 processors activated. [ 0.325075] CPU features: detected feature: 32-bit EL0 Support [ 0.325341] CPU: All CPU(s) started at EL2 [ 0.325358] alternatives: patching kernel code [ 0.333798] devtmpfs: initialized [ 0.372399] Initilizing CustomIPI irq domain [ 0.372719] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.372736] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.384227] pinctrl core: initialized pinctrl subsystem [ 0.384841] OS set in device tree is not L4T. [ 0.385333] regulator-dummy: no parameters [ 0.385619] Initializing plugin-manager [ 0.385781] Plugin module not found [ 0.385972] node /plugin-manager/fragement@0 match with board >=3448-0000-100 [ 0.386491] node /plugin-manager/fragment@1 match with board >=3448-0000-101 [ 0.387462] node /plugin-manager/fragement@7 match with odm-data enable-pmic-wdt [ 0.387666] node /plugin-manager/fragement@8 match with odm-data enable-pmic-wdt [ 0.388303] node /plugin-manager/fragement@13 match with board >=3448-0000-300 [ 0.391966] NET: Registered protocol family 16 [ 0.393455] pstore: using zlib compression [ 0.393499] console [pstore-1] enabled [ 0.393504] pstore: Registered ramoops as persistent store backend [ 0.393509] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.409119] cpuidle: using governor menu [ 0.413258] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.414935] vdso: 2 pages (1 code @ ffffff8008f87000, 1 data @ ffffff8009e84000) [ 0.414959] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.417698] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.420045] Serial: AMBA PL011 UART driver [ 0.420560] tegra_powergate_init: DONE [ 0.420576] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.420583] DTB Build time: Jul 26 2021 12:16:29 [ 0.422509] Tegra reboot handler registered. [ 0.427180] iommu: Adding device tegra-carveouts to group 0 [ 0.427323] platform tegra-carveouts: domain=ffffffc0f942a3d8 allocates as[0]=ffffffc0f94300a8 [ 0.427675] iommu: Adding device smmu_test to group 1 [ 0.427728] platform smmu_test: domain=ffffffc0f942a618 allocates as[0]=ffffffc0f9430110 [ 0.428579] mc: mapped MMIO address: 0xffffff8008041000 -> 0x70019000 [ 0.428637] mc: mapped MMIO address: 0xffffff8008067000 -> 0x7001c000 [ 0.428692] mc: mapped MMIO address: 0xffffff800807b000 -> 0x7001d000 [ 0.428703] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.428724] mc-err: mcerr ops are set to t21x [ 0.439291] iommu: Adding device 70090000.xusb to group 2 [ 0.439573] iommu: Adding device 70006000.serial to group 3 [ 0.439637] platform 70006000.serial: domain=ffffffc0f944bcd8 allocates as[0]=ffffffc0f9430178 [ 0.440084] iommu: Adding device 70006040.serial to group 4 [ 0.440351] iommu: Adding device 70006200.serial to group 5 [ 0.440550] iommu: Adding device sound to group 6 [ 0.440608] platform sound: domain=ffffffc0f94b2258 allocates as[0]=ffffffc0f94301e0 [ 0.441213] iommu: Adding device 7000d400.spi to group 7 [ 0.441523] iommu: Adding device 7000d600.spi to group 8 [ 0.441800] iommu: Adding device 70410000.spi to group 9 [ 0.442107] iommu: Adding device 50000000.host1x to group 10 [ 0.442377] iommu: Adding device 54080000.vi to group 11 [ 0.442777] iommu: Adding device 54600000.isp to group 12 [ 0.443063] iommu: Adding device 54680000.isp to group 13 [ 0.443337] iommu: Adding device tegradc.0 to group 14 [ 0.443390] platform tegradc.0: domain=ffffffc0f94c4198 allocates as[0]=ffffffc0f9430248 [ 0.447580] platform tegradc.0: IOVA linear map 0x0000000092ca9000(800000) [ 0.447973] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.448310] iommu: Adding device tegradc.1 to group 15 [ 0.448381] platform tegradc.1: domain=ffffffc0f94c43d8 allocates as[0]=ffffffc0f94302b0 [ 0.452549] platform tegradc.1: IOVA linear map 0x0000000092ca9000(800000) [ 0.452939] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.453224] iommu: Adding device 54340000.vic to group 16 [ 0.453429] iommu: Adding device 544c0000.nvenc to group 17 [ 0.453634] iommu: Adding device 54500000.tsec to group 18 [ 0.453827] iommu: Adding device 54100000.tsecb to group 19 [ 0.454019] iommu: Adding device 54480000.nvdec to group 20 [ 0.454195] iommu: Adding device 54380000.nvjpg to group 21 [ 0.455245] iommu: Adding device 546c0000.i2c to group 22 [ 0.455559] iommu: Adding device 57000000.gpu to group 23 [ 0.455639] platform 57000000.gpu: domain=ffffffc0f95263d8 allocates as[0]=ffffffc0f9430318 [ 0.455677] platform 57000000.gpu: domain=ffffffc0f95263d8 allocates as[1]=ffffffc0f9430380 [ 0.455716] platform 57000000.gpu: domain=ffffffc0f95263d8 allocates as[2]=ffffffc0f94303e8 [ 0.455749] platform 57000000.gpu: domain=ffffffc0f95263d8 allocates as[3]=ffffffc0f9430450 [ 0.456649] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.456658] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.456670] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET [ 0.456674] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.456678] tegra-pmc: ### PMC reset status reg: 0x3 [ 0.509338] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.509347] tegra-pmc: Clear bootloader IO dpd settings [ 0.509368] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.509432] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.509730] iommu: Adding device 70012000.se to group 24 [ 0.510517] iommu: Adding device 7000c000.i2c to group 25 [ 0.510784] iommu: Adding device 7000c400.i2c to group 26 [ 0.511028] iommu: Adding device 7000c500.i2c to group 27 [ 0.511301] iommu: Adding device 7000c700.i2c to group 28 [ 0.511558] iommu: Adding device 7000d000.i2c to group 29 [ 0.511817] iommu: Adding device 7000d100.i2c to group 30 [ 0.512159] iommu: Adding device sdhci-tegra.0 to group 31 [ 0.512222] platform sdhci-tegra.0: domain=ffffffc0f9570558 allocates as[0]=ffffffc0f94304b8 [ 0.513059] iommu: Adding device 700d0000.xudc to group 32 [ 0.516328] vdd-ac-bat: 5000 mV [ 0.516701] vdd-5v0-sys: 5000 mV [ 0.517424] vdd-5v0-hdmi: 5000 mV [ 0.517846] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.518140] vdd-1v8-sys: 1800 mV [ 0.518529] vdd-fan: 5000 mV [ 0.518784] vdd-fan: supplied by vdd-5v0-sys [ 0.518998] vdd-usb-vbus: 5000 mV [ 0.519206] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.519571] vdd-usb-vbus2: 5000 mV [ 0.553993] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.556250] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.557752] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.557784] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.557803] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.558164] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.566321] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.566677] SCSI subsystem initialized [ 0.566868] libata version 3.00 loaded. [ 0.567155] usbcore: registered new interface driver usbfs [ 0.567208] usbcore: registered new interface driver hub [ 0.567255] usbcore: registered new device driver usb [ 0.571236] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.577094] random: fast init done [ 0.577100] vdd-core: 600 <--> 1162 mV at 1075 mV [ 0.578084] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.581006] vdd-ddr-1v1: 1150 mV [ 0.584993] vdd-pre-reg-1v35: 1350 mV [ 0.588991] vdd-1v8: 1800 mV [ 0.592987] avdd-sys-1v2: 1200 mV [ 0.596988] vdd-pex-1v0: 1050 mV [ 0.597606] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.598131] max77620-ldo3: at 3100 mV [ 0.600990] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.601530] max77620-ldo5: at 3100 mV [ 0.604990] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [ 0.608987] avdd-1v05-pll: 1050 mV [ 0.612987] avdd-io-hdmi-dp: 1050 mV [ 0.615427] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.615711] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.616001] max77620 4-003c: max77620 probe successful [ 0.618772] media: Linux media interface: v0.10 [ 0.618830] Linux video capture interface: v2.00 [ 0.619723] pps_core: LinuxPPS API ver. 1 registered [ 0.619728] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.619747] PTP clock support registered [ 0.623113] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.624022] Advanced Linux Sound Architecture Driver Initialized. [ 0.624711] Bluetooth: Core ver 2.22 [ 0.624758] NET: Registered protocol family 31 [ 0.624763] Bluetooth: HCI device and connection manager initialized [ 0.624776] Bluetooth: HCI socket layer initialized [ 0.624784] Bluetooth: L2CAP socket layer initialized [ 0.624814] Bluetooth: SCO socket layer initialized [ 0.626649] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.626665] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.626720] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.626734] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.630282] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.631603] vdd-3v3-sys: 3300 mV [ 0.631986] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.632042] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.636416] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.636881] vdd-3v3-sd: 3300 mV [ 0.637326] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.637845] avdd-io-edp-1v05: 1050 mV [ 0.638227] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.638366] vdd-usb-hub-en: 5000 mV [ 0.638707] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.639937] camchar: rtcpu character device driver loaded [ 0.640671] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [ 0.642067] clocksource: Switched to clocksource arch_sys_counter [ 0.683137] VFS: Disk quotas dquot_6.6.0 [ 0.683271] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.683771] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.684257] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.684287] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.684492] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.684498] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.684511] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.684538] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.684545] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.684557] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.684565] nvmap_page_pool_init: Total RAM pages: 1008854 [ 0.684570] nvmap_page_pool_init: nvmap page pool size: 126106 pages (492 MB) [ 0.684666] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.685157] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.686284] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.694735] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.695162] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.695517] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.695784] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.695956] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.696249] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.696254] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.696686] NET: Registered protocol family 2 [ 0.697681] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.697893] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.698492] TCP: Hash tables configured (established 32768 bind 32768) [ 0.698656] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.698735] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.699154] NET: Registered protocol family 1 [ 0.699818] RPC: Registered named UNIX socket transport module. [ 0.699823] RPC: Registered udp transport module. [ 0.699827] RPC: Registered tcp transport module. [ 0.699831] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.699845] PCI: CLS 0 bytes, default 64 [ 0.700077] Trying to unpack rootfs image as initramfs... [ 1.006352] Freeing initrd memory: 6992K [ 1.016528] host1x 50000000.host1x: initialized [ 1.018455] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.021817] audit: initializing netlink subsys (disabled) [ 1.021915] audit: type=2000 audit(0.871:1): initialized [ 1.022713] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.032705] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.034249] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.035049] 9p: Installing v9fs 9p2000 file system support [ 1.038370] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 1.038522] io scheduler noop registered [ 1.038805] io scheduler cfq registered (default) [ 1.041577] gic 702f9000.agic: GIC IRQ controller registered [ 1.044683] iommu: Adding device 702ef000.adsp to group 33 [ 1.053613] iommu: Adding device aconnect@702c0000:adsp_audio to group 34 [ 1.053770] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 1.054434] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x71a9411 [ 1.054443] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 1.056114] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 1.056221] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 1.056318] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 1.056517] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 1.056615] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 1.056711] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 1.056803] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 1.056891] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 1.056976] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 1.057065] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 1.063307] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 1.065012] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 1.067010] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.068312] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 1.068671] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.069927] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.070209] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 1.070228] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 1.070471] Adding domain tsec-pd to PM domain host1x-pd [ 1.073476] tsec 54500000.tsec: initialized [ 1.075026] tsec 54100000.tsecb: initialized [ 1.075761] Adding domain nvdec-pd to PM domain host1x-pd [ 1.079246] nvdec 54480000.nvdec: initialized [ 1.080337] Adding domain vic03-pd to PM domain host1x-pd [ 1.080524] Adding domain msenc-pd to PM domain host1x-pd [ 1.080681] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.085032] falcon 54340000.vic: initialized [ 1.086373] falcon 544c0000.nvenc: initialized [ 1.087723] falcon 54380000.nvjpg: initialized [ 1.092248] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97 [ 1.092298] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.092343] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.092498] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.092598] display board info: id 0x0, fab 0x0 [ 1.092659] generic_infoframe_type: 0x87 [ 1.092667] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.092672] tegra_cec 70015000.tegra_cec: probed [ 1.092818] tegradc tegradc.0: DT parsed successfully [ 1.092870] tegradc tegradc.0: Display dc.ffffff800abc0000 registered with id=0 [ 1.093484] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 1920x1080 (on 0x0mm) pclk=148350781 [ 1.097062] tegradc tegradc.0: probed [ 1.102704] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.109768] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.111051] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check disabled [ 1.111061] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.111451] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 1.111465] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.111471] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 1.111477] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 1.111486] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.111553] pci 0000:00:01.0: [10de:0fae] type 01 class 0x060400 [ 1.111602] kfuse 7000fc00.kfuse: initialized [ 1.111714] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.112123] pci 0000:00:02.0: [10de:0faf] type 01 class 0x060400 [ 1.112720] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.113042] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.113059] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.113318] pci 0000:01:00.0: [8086:24fd] type 00 class 0x028000 [ 1.113363] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.113382] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 1.113698] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.114564] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.116444] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.116461] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.116976] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.118585] vdd-gpu: applied init 1000000uV constraint [ 1.118599] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.119069] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.122293] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.122590] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [ 1.122638] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [ 1.122680] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 1.122708] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit] [ 1.122923] pci 0000:02:00.0: supports D1 D2 [ 1.122928] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.125195] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.125289] No Device Node present for smmu client: serial8250 !! [ 1.125297] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.125336] iommu: Adding device serial8250 to group 35 [ 1.128196] console [ttyS0] disabled [ 1.128275] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.128374] console [ttyS0] enabled [ 1.129374] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 1.129727] serial-tegra 70006200.serial: RX in PIO mode [ 1.129828] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 1.130780] Console: switching to colour frame buffer device 240x67 [ 1.130905] tegradc tegradc.0: fb registered [ 1.131317] [drm] Initialized [ 1.134278] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.134379] pci 0000:00:01.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [ 1.134388] pci 0000:00:02.0: BAR 14: assigned [mem 0x13100000-0x131fffff] [ 1.134395] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.134408] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 1.134436] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.134445] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 1.134460] pci 0000:02:00.0: BAR 4: assigned [mem 0x13100000-0x13103fff 64bit] [ 1.134482] pci 0000:02:00.0: BAR 2: assigned [mem 0x13104000-0x13104fff 64bit] [ 1.134502] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 1.134511] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.134517] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 1.134524] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 1.135191] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt [ 1.135200] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 1.135209] pcie_pme 0000:00:01.0:pcie001: service driver pcie_pme loaded [ 1.135392] aer 0000:00:01.0:pcie002: service driver aer loaded [ 1.135702] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 1.135709] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 1.135717] pcie_pme 0000:00:02.0:pcie001: service driver pcie_pme loaded [ 1.135838] aer 0000:00:02.0:pcie002: service driver aer loaded [ 1.137690] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [ 1.137738] tegradc tegradc.0: hdmi: tmds rate:148351K prod-setting:prod_c_hdmi_75m_150m [ 1.138327] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [ 1.138339] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [ 1.144085] brd: module loaded [ 1.149666] loop: module loaded [ 1.149754] tegra_profiler: version: 1.145, samples/io: 49/28 [ 1.149871] tegra_profiler: auth: init [ 1.151401] THERMAL EST: found 2 subdevs [ 1.151411] THERMAL EST num_resources: 0 [ 1.151417] [THERMAL EST subdev 0] [ 1.151425] [THERMAL EST subdev 1] [ 1.151990] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 1.151994] THERMAL EST: thz register success. [ 1.152166] THERMAL EST: end of probe, return err: 0 [ 1.153457] sd: No Scsi addr parsed to reserve index [ 1.153496] hisi_sas: driver version v1.6 [ 1.158704] tegra-qspi 70410000.spi: Prod settings list not found [ 1.159978] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes) [ 1.159989] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0 [ 1.163053] libphy: Fixed MDIO Bus: probed [ 1.164057] tun: Universal TUN/TAP device driver, 1.6 [ 1.164062] tun: (C) 1999-2004 Max Krasnyansky [ 1.164816] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 1.164823] Extcon AUX1(HDMI) enable [ 1.165232] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.165238] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.165300] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.165303] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.165356] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.165362] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.165417] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.4.0-k [ 1.165422] ixgbe: Copyright (c) 1999-2016 Intel Corporation. [ 1.165996] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 1.166369] tegradc tegradc.1: No lt-data, using default setting [ 1.166414] tegradc tegradc.1: No hpd-gpio in DT [ 1.166454] tegradc tegradc.1: DT parsed successfully [ 1.166512] tegradc tegradc.1: Display dc.ffffff800d540000 registered with id=1 [ 1.167739] r8168 0000:02:00.0: enabling device (0000 -> 0003) [ 1.167773] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 1.170766] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.180748] tegradc tegradc.1: probed [ 1.182706] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 1.182851] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:ea:cc:9b from device tree [ 1.183478] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 1.183550] r8168 Copyright (C) 2017 Realtek NIC software team This program comes with ABSOLUTELY NO WARRANTY; for details, please see . This is free software, and you are welcome to redistribute it under certain conditions; see . [ 1.184335] PPP generic driver version 2.4.2 [ 1.190534] PPP BSD Compression module registered [ 1.190540] PPP Deflate Compression module registered [ 1.190582] PPP MPPE Compression module registered [ 1.190589] NET: Registered protocol family 24 [ 1.190676] usbcore: registered new interface driver r8152 [ 1.190732] usbcore: registered new interface driver asix [ 1.190806] usbcore: registered new interface driver ax88179_178a [ 1.190848] usbcore: registered new interface driver cdc_ether [ 1.190897] usbcore: registered new interface driver net1080 [ 1.190941] usbcore: registered new interface driver cdc_subset [ 1.190984] usbcore: registered new interface driver zaurus [ 1.191031] tegradc tegradc.1: fb registered [ 1.191043] usbcore: registered new interface driver cdc_ncm [ 1.191365] VFIO - User Level meta-driver version: 0.3 [ 1.194272] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 1.194279] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 1.194288] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 1.194305] tegradc tegradc.1: blank - powerdown [ 1.194325] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 1.194330] Extcon DP: HPD disabled [ 1.194333] hpd: hpd_switch 0 [ 1.194338] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 1.194346] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 1.194353] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 1.195987] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.196013] ehci-pci: EHCI PCI platform driver [ 1.196059] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.196070] ohci-pci: OHCI PCI platform driver [ 1.196110] ohci-platform: OHCI generic platform driver [ 1.198885] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 1.206945] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 1.208699] tegradc tegradc.0: nominal-pclk:148351648 parent:148350781 div:1.0 pclk:148350781 146868084~161703244 [ 1.209220] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f974c800 id [ 1.210775] usbcore: registered new interface driver uas [ 1.210823] usbcore: registered new interface driver usb-storage [ 1.210885] usbcore: registered new interface driver usbserial [ 1.212724] tegra-xusb 70090000.xusb: Firmware timestamp: 2020-07-31 09:33:12 UTC, Version: 50.26 release [ 1.212757] tegra-xusb 70090000.xusb: xHCI Host Controller [ 1.212775] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 1.213489] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 1.213524] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 1.213684] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.213691] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.213696] usb usb1: Product: xHCI Host Controller [ 1.213701] usb usb1: Manufacturer: Linux 4.9.253-tegra xhci-hcd [ 1.213705] usb usb1: SerialNumber: 70090000.xusb [ 1.214149] hub 1-0:1.0: USB hub found [ 1.214185] hub 1-0:1.0: 5 ports detected [ 1.214714] tegra-xusb 70090000.xusb: xHCI Host Controller [ 1.214726] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 1.214802] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.214905] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.214911] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.214915] usb usb2: Product: xHCI Host Controller [ 1.214920] usb usb2: Manufacturer: Linux 4.9.253-tegra xhci-hcd [ 1.214924] usb usb2: SerialNumber: 70090000.xusb [ 1.215402] hub 2-0:1.0: USB hub found [ 1.215435] hub 2-0:1.0: 4 ports detected [ 1.216155] tegra-xudc-new 700d0000.xudc: device count: 1 [ 1.216166] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 1.216172] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 1.217132] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 1.217142] tegra-xudc-new 700d0000.xudc: vbus state: 0 [ 1.217498] tegra-xudc-new 700d0000.xudc: entering ELPG [ 1.217672] mousedev: PS/2 mouse device common for all mice [ 1.217741] usbcore: registered new interface driver xpad [ 1.217746] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 1.297601] tegradc tegradc.0: blank - powerdown [ 1.318164] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 1.318254] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 2 [ 1.318481] usb usb2: usb_suspend_both: status 0 [ 1.343415] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 1.343418] Extcon AUX1(HDMI) disable [ 1.346361] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 1.348482] rtc rtc1: alarm rtc device [ 1.348495] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.348513] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.348885] i2c /dev entries driver [ 1.350332] i2c i2c-6: Added multiplexed i2c bus 7 [ 1.350650] i2c i2c-6: Added multiplexed i2c bus 8 [ 1.350656] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 1.351222] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [ 1.376474] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [ 1.399752] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 1.399828] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.399954] imx219 8-0010: board setup failed [ 1.400032] imx219: probe of 8-0010 failed with error -121 [ 1.401607] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 1.403598] tegradc tegradc.0: unblank [ 1.404348] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 1.404352] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 1.404808] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.404823] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 1.404830] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 1.404967] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.404978] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 1.404984] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 1.405131] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.405142] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 1.405146] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 1.405332] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 1.406225] tegra_aotag tegra-aotag: Registering sensor 0 [ 1.406286] tegra_aotag tegra-aotag: Invalid temp readout [ 1.406310] tegra_aotag tegra-aotag: Invalid temp readout [ 1.406327] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 1.406336] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 1.407446] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.407463] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 1.407648] tegra_aotag tegra-aotag: Invalid temp readout [ 1.407678] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 1.408196] parse_throttle_dt_data: Num cap clks = 6 [ 1.408201] parse_throttle_dt_data: clk=cclk_g type=2 [ 1.408216] parse_throttle_dt_data: clk=gpu type=4 [ 1.408244] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 1.408265] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 1.408293] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 1.408297] parse_throttle_dt_data: clk=emc type=3 [ 1.408679] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.408808] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.408961] tegra_throttle_probe: probe successful. #cdevs=4 [ 1.409873] FAN dev name: pwm-fan [ 1.409953] FAN:gpio request success. [ 1.410022] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 1.410393] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 1.410559] pwm_fan_driver pwm-fan: fan tach request irq success [ 1.410570] pwm_fan_driver pwm-fan: tach period: 1000 [ 1.410670] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 1.410674] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 1.410679] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 1.410683] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 1.410687] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 1.410691] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 1.410695] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 1.410698] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 1.410702] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 1.410706] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 1.413552] device-mapper: uevent: version 1.0.3 [ 1.414029] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 1.418729] tegra210-cpufreq cpufreq: probe()...completed [ 1.419533] sdhci: Secure Digital Host Controller Interface driver [ 1.419534] sdhci: Copyright(c) Pierre Ossman [ 1.419536] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.420041] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 1.420396] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 1.420515] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300 [ 1.423233] tegradc tegradc.0: nominal-pclk:241500000 parent:241500000 div:1.0 pclk:241500000 239085000~263235000 [ 1.423282] tegradc tegradc.0: hdmi: tmds rate:241500K prod-setting:prod_c_hdmi_150m_300m [ 1.424250] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 1.425204] tegra-se 70012000.se: tegra_se_probe: complete [ 1.425727] hidraw: raw HID events driver (C) Jiri Kosina [ 1.426937] usbcore: registered new interface driver usbhid [ 1.426938] usbhid: USB HID core driver [ 1.429036] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 1.429199] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 1.431230] nvpmodel: initialized successfully [ 1.432181] usbcore: registered new interface driver snd-usb-audio [ 1.432236] No Device Node present for smmu client: snd-soc-dummy !! [ 1.432241] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.432258] iommu: Adding device snd-soc-dummy to group 36 [ 1.440053] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 1.448340] OPE platform probe [ 1.448424] OPE platform probe successful [ 1.448449] OPE platform probe [ 1.448530] OPE platform probe successful [ 1.458899] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 1.458902] Extcon AUX1(HDMI) enable [ 1.466393] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 1.472951] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 1.473074] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 1.473197] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 1.473317] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 1.473441] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 1.473558] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 1.473675] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 1.473795] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 1.473912] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 1.474031] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 1.474557] tegradc tegradc.0: sync windows ret = 246 [ 1.486010] u32 classifier [ 1.486012] Actions configured [ 1.486109] Initializing XFRM netlink socket [ 1.486827] NET: Registered protocol family 10 [ 1.487548] NET: Registered protocol family 17 [ 1.487559] NET: Registered protocol family 15 [ 1.487630] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.487678] Bluetooth: RFCOMM socket layer initialized [ 1.487686] Bluetooth: RFCOMM ver 1.11 [ 1.487691] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.487695] Bluetooth: HIDP socket layer initialized [ 1.487712] 9pnet: Installing 9P2000 support [ 1.487748] Key type dns_resolver registered [ 1.488128] Registered cp15_barrier emulation handler [ 1.488134] Registered setend emulation handler [ 1.489196] registered taskstats version 1 [ 1.489827] Adding domain ve2-pd to PM domain host1x-pd [ 1.490089] Adding domain ve-pd to PM domain host1x-pd [ 1.492255] isp 54600000.isp: initialized [ 1.494212] isp 54680000.isp: initialized [ 1.504684] last reset is due to software reset [ 1.504687] KERNEL: PMC reset status reg: 0x3 [ 1.504747] BL: PMC reset status reg: 0x3 [ 1.504749] BL: PMIC poweroff Event Recorder: 0x0 [ 1.506321] clk_cbus_recalc_rate: no gbus parent [ 1.506326] clk_cbus_round_rate: no gbus parent [ 1.506328] clk_cbus_round_rate: no gbus parent [ 1.506335] clk_cbus_recalc_rate: no gbus parent [ 1.506438] clk_cbus_recalc_rate: no gbus parent [ 1.506440] clk_cbus_round_rate: no gbus parent [ 1.506442] clk_cbus_round_rate: no gbus parent [ 1.506445] clk_cbus_recalc_rate: no gbus parent [ 1.507114] tegra_dvfs: GPU-cap: registered [ 1.507169] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 1.507171] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled [ 1.507173] tegra dvfs: vdd-gpu: nominal 1048mV, offset 708000uV, step 10000uV, scaling enabled [ 1.508616] tegra_dvfs: vdd-gpu-vts: registered [ 1.509323] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 1.509920] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 1.510420] input: gpio-keys as /devices/gpio-keys/input/input1 [ 1.516691] extcon-disp-state extcon:disp-state: cable 51 state 1 [ 1.516694] Extcon HDMI: HPD enabled [ 1.516713] tegradc tegradc.0: hdmi: plugged [ 1.542080] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 1.542812] tegra_rtc 7000e000.rtc: setting system clock to 2022-06-29 06:52:50 UTC (1656485570) [ 1.543835] vi 54080000.vi: vi_probe: ++ [ 1.546515] vi 54080000.vi: initialized [ 1.548680] vi 54080000.vi: subdev nvcsi--2 bound [ 1.548699] vi 54080000.vi: subdev imx219 7-0010 bound [ 1.550421] vi 54080000.vi: subdev nvcsi--1 bound [ 1.551892] Disable partitions left on by BL [ 1.551895] disb [ 1.551945] bwmgr: missing cdev-type property [ 1.552042] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.552049] DRAM derating cdev registered. [ 1.552935] ALSA device list: [ 1.552939] #0: tegra-hda at 0x70038000 irq 83 [ 1.552941] #1: tegra-snd-t210ref-mobile-rt565x [ 1.556053] Freeing unused kernel memory: 8640K [ 1.571326] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411 [ 1.571332] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.571336] usb 1-2: Product: 4-Port USB 2.1 Hub [ 1.571340] usb 1-2: Manufacturer: Generic [ 1.572313] hub 1-2:1.0: USB hub found [ 1.572888] hub 1-2:1.0: 4 ports detected [ 1.581322] Root device found: mmcblk0p1 [ 1.664905] mmc0: Applying tuning correction [ 1.664920] mmc0: Tap value after applying correction 62 [ 1.664937] mmc0: hw tuning done ... [ 1.664970] mmc0: new ultra high speed SDR104 SDXC card at address aaaa [ 1.665334] mmcblk0: mmc0:aaaa SF128 119 GiB [ 1.670026] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 [ 1.682473] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 1.711218] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411 [ 1.711225] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.711228] usb 2-1: Product: 4-Port USB 3.1 Hub [ 1.711232] usb 2-1: Manufacturer: Generic [ 1.714552] hub 2-1:1.0: USB hub found [ 1.715374] hub 2-1:1.0: 4 ports detected [ 1.786317] Found dev node: /dev/mmcblk0p1 [ 1.826088] usb 1-3: new full-speed USB device number 3 using tegra-xusb [ 1.827186] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 1.829229] Rootfs mounted over mmcblk0p1 [ 1.847846] usb 1-3: New USB device found, idVendor=8087, idProduct=0a2b [ 1.847852] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.856667] Switching from initrd to actual rootfs [ 1.926097] usb 1-2.2: new full-speed USB device number 4 using tegra-xusb [ 1.952859] usb 1-2.2: New USB device found, idVendor=0403, idProduct=6001 [ 1.952864] usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1.952868] usb 1-2.2: Product: FT232R USB UART [ 1.952871] usb 1-2.2: Manufacturer: FTDI [ 1.952874] usb 1-2.2: SerialNumber: AH072IC1 [ 2.026466] usb 2-1.1: new SuperSpeed USB device number 3 using tegra-xusb [ 2.047450] usb 2-1.1: New USB device found, idVendor=090c, idProduct=1000 [ 2.047455] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.047459] usb 2-1.1: Product: Flash Drive [ 2.047461] usb 2-1.1: Manufacturer: Samsung [ 2.047464] usb 2-1.1: SerialNumber: 0374121010002324 [ 2.048371] usb-storage 2-1.1:1.0: USB Mass Storage device detected [ 2.048570] usb-storage 2-1.1:1.0: Quirks match for vid 090c pid 1000: 400 [ 2.048604] scsi host0: usb-storage 2-1.1:1.0 [ 2.098094] tegra_cec 70015000.tegra_cec: physical address: 10:00. [ 2.105252] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.117999] cgroup: cgroup2: unknown option "nsdelegate" [ 2.126772] usb 1-2.3: new full-speed USB device number 5 using tegra-xusb [ 2.146953] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 2.147905] systemd[1]: Detected architecture arm64. [ 2.148002] usb 1-2.3: New USB device found, idVendor=0d8c, idProduct=0014 [ 2.148007] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.148011] usb 1-2.3: Product: USB Audio Device [ 2.148014] usb 1-2.3: Manufacturer: C-Media Electronics Inc. [ 2.162612] tegra_cec 70015000.tegra_cec: Sent res: -113. [ 2.162616] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 2.165944] input: C-Media Electronics Inc. USB Audio Device as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.3/0003:0D8C:0014.0001/input/input2 [ 2.176267] systemd[1]: Set hostname to . [ 2.222581] hid-generic 0003:0D8C:0014.0001: input,hidraw0: USB HID v1.00 Device [C-Media Electronics Inc. USB Audio Device] on usb-70090000.xusb-2.3/input3 [ 2.302081] usb 1-2.4: new full-speed USB device number 6 using tegra-xusb [ 2.325737] usb 1-2.4: New USB device found, idVendor=046d, idProduct=c52b [ 2.325743] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.325747] usb 1-2.4: Product: USB Receiver [ 2.325750] usb 1-2.4: Manufacturer: Logitech [ 2.357578] systemd[1]: Configuration file /etc/systemd/system/at_stop_pyscript.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 2.360617] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 2.360626] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 2.618266] random: systemd: uninitialized urandom read (16 bytes read) [ 2.618297] systemd[1]: Reached target User and Group Name Lookups. [ 2.618482] random: systemd: uninitialized urandom read (16 bytes read) [ 2.620022] systemd[1]: Created slice System Slice. [ 2.620086] random: systemd: uninitialized urandom read (16 bytes read) [ 2.620244] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 2.620398] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 2.696976] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 2.841160] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [ 2.881768] systemd-journald[2042]: Received request to flush runtime journal from PID 1 [ 3.325387] scsi 0:0:0:0: Direct-Access Samsung Flash Drive 1100 PQ: 0 ANSI: 6 [ 3.334630] sd 0:0:0:0: [sda] 250626566 512-byte logical blocks: (128 GB/120 GiB) [ 3.342668] sd 0:0:0:0: [sda] Write Protect is off [ 3.347876] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 3.348085] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.362739] sda: sda1 [ 3.363928] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 3.955405] random: crng init done [ 3.958838] random: 7 urandom warning(s) missed due to ratelimiting [ 4.048356] using random self ethernet address [ 4.055187] using random host ethernet address [ 4.163233] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.163255] cpu-throttle-alert cooling device registered. [ 4.163505] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.163521] gpu-throttle-alert cooling device registered. [ 4.163690] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.163703] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.163716] hot-surface-alert cooling device registered. [ 4.217345] Intel(R) Wireless WiFi driver for Linux [ 4.217349] Copyright(c) 2003- 2015 Intel Corporation [ 4.217562] iwlwifi 0000:01:00.0: enabling device (0000 -> 0002) [ 4.222436] usbcore: registered new interface driver btusb [ 4.224156] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015 [ 4.225156] Bluetooth: hci0: Device revision is 16 [ 4.225160] Bluetooth: hci0: Secure boot is enabled [ 4.225163] Bluetooth: hci0: OTP lock is enabled [ 4.225165] Bluetooth: hci0: API lock is enabled [ 4.225167] Bluetooth: hci0: Debug lock is disabled [ 4.225170] Bluetooth: hci0: Minimum firmware build 1 week 10 2014 [ 4.276795] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-26.ucode failed with error -2 [ 4.294095] iwlwifi 0000:01:00.0: Falling back to user helper [ 4.295507] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi [ 4.679256] logitech-djreceiver 0003:046D:C52B.0004: hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-70090000.xusb-2.4/input2 [ 4.749851] usbcore: registered new interface driver ftdi_sio [ 4.749892] usbserial: USB Serial support registered for FTDI USB Serial Device [ 4.750696] ftdi_sio 1-2.2:1.0: FTDI USB Serial Device converter detected [ 4.750806] usb 1-2.2: Detected FT232RL [ 4.751140] usb 1-2.2: FTDI USB Serial Device converter now attached to ttyUSB0 [ 5.149080] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-25.ucode failed with error -2 [ 5.155541] input: Logitech Performance MX as /devices/70090000.xusb/usb1/1-2/1-2.4/1-2.4:1.2/0003:046D:C52B.0004/0003:046D:101A.0005/input/input3 [ 5.155876] logitech-hidpp-device 0003:046D:101A.0005: input,hidraw2: USB HID v1.11 Mouse [Logitech Performance MX] on usb-70090000.xusb-2.4:1 [ 5.158557] iwlwifi 0000:01:00.0: Falling back to user helper [ 5.161826] input: Logitech M720 Triathlon as /devices/70090000.xusb/usb1/1-2/1-2.4/1-2.4:1.2/0003:046D:C52B.0004/0003:046D:405E.0006/input/input4 [ 5.162808] logitech-hidpp-device 0003:046D:405E.0006: input,hidraw3: USB HID v1.11 Keyboard [Logitech M720 Triathlon] on usb-70090000.xusb-2.4:3 [ 5.167759] input: Logitech K270 as /devices/70090000.xusb/usb1/1-2/1-2.4/1-2.4:1.2/0003:046D:C52B.0004/0003:046D:4003.0007/input/input5 [ 5.168411] logitech-hidpp-device 0003:046D:4003.0007: input,hidraw4: USB HID v1.11 Keyboard [Logitech K270] on usb-70090000.xusb-2.4:4 [ 5.173913] input: Logitech M720 Triathlon as /devices/70090000.xusb/usb1/1-2/1-2.4/1-2.4:1.2/0003:046D:C52B.0004/0003:046D:405E.0008/input/input6 [ 5.175140] logitech-hidpp-device 0003:046D:405E.0008: input,hidraw5: USB HID v1.11 Keyboard [Logitech M720 Triathlon] on usb-70090000.xusb-2.4:5 [ 5.179839] input: Logitech K370s/K375s as /devices/70090000.xusb/usb1/1-2/1-2.4/1-2.4:1.2/0003:046D:C52B.0004/0003:046D:4061.0009/input/input7 [ 5.181881] logitech-hidpp-device 0003:046D:4061.0009: input,hidraw6: USB HID v1.11 Keyboard [Logitech K370s/K375s] on usb-70090000.xusb-2.4:6 [ 5.239664] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-24.ucode failed with error -2 [ 5.249643] iwlwifi 0000:01:00.0: Falling back to user helper [ 5.344809] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-23.ucode failed with error -2 [ 5.354320] iwlwifi 0000:01:00.0: Falling back to user helper [ 5.422741] iwlwifi 0000:01:00.0: loaded firmware version 22.391740.0 op_mode iwlmvm [ 5.619627] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 8265, REV=0x230 [ 5.621770] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 5.622466] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 5.632876] Mass Storage Function, version: 2009/09/11 [ 5.632882] LUN: removable file: (no medium) [ 5.639041] using random self ethernet address [ 5.643624] using random host ethernet address [ 5.742451] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 5.742461] Bluetooth: BNEP socket layer initialized [ 5.742738] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' [ 5.743648] thermal thermal_zone6: failed to read out thermal zone (-5) [ 5.750588] thermal thermal_zone6: Registering thermal zone thermal_zone6 for type iwlwifi_1 [ 5.785779] rndis0: HOST MAC 4e:31:7c:24:79:dc [ 5.790787] rndis0: MAC 4e:31:7c:24:79:dd [ 5.796415] usb0: HOST MAC 4e:31:7c:24:79:de [ 5.796454] usb0: MAC 4e:31:7c:24:79:df [ 5.796479] tegra-xudc-new 700d0000.xudc: exiting ELPG [ 5.797606] tegra-xudc-new 700d0000.xudc: exiting ELPG done [ 5.797629] tegra-xudc-new 700d0000.xudc: ep 0 (type: 0, dir: out) enabled [ 5.797769] tegra-xudc-new 700d0000.xudc: entering ELPG [ 5.798010] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 5.798038] tegra-xudc-new 700d0000.xudc: exiting ELPG [ 5.799169] tegra-xudc-new 700d0000.xudc: exiting ELPG done [ 5.799186] tegra-xudc-new 700d0000.xudc: entering ELPG [ 5.799531] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 5.816644] l4tbr0: port 1(rndis0) entered blocking state [ 5.816650] l4tbr0: port 1(rndis0) entered disabled state [ 5.820249] device rndis0 entered promiscuous mode [ 5.829297] IPv6: ADDRCONF(NETDEV_UP): rndis0: link is not ready [ 5.839595] l4tbr0: port 2(usb0) entered blocking state [ 5.839601] l4tbr0: port 2(usb0) entered disabled state [ 5.840350] device usb0 entered promiscuous mode [ 5.842190] Bluetooth: hci0: Waiting for firmware download to complete [ 5.843135] Bluetooth: hci0: Firmware loaded in 1582797 usecs [ 5.843253] Bluetooth: hci0: Waiting for device to boot [ 5.855141] Bluetooth: hci0: Device booted in 11671 usecs [ 5.859695] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 5.864618] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc [ 5.867166] Bluetooth: hci0: Applying Intel DDC parameters completed [ 6.720350] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.721416] eth0: 0xffffff800a40c000, 00:04:4b:ea:cc:9b, IRQ 406 [ 6.780529] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.857624] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6.860487] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 6.860800] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 6.977527] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 6.977839] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 7.059741] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 7.161899] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 7.577797] zram: Added device: zram0 [ 7.578525] zram: Added device: zram1 [ 7.580863] zram: Added device: zram2 [ 7.584672] zram: Added device: zram3 [ 7.640538] zram0: detected capacity change from 0 to 518537216 [ 7.963981] Adding 506380k swap on /dev/zram0. Priority:5 extents:1 across:506380k SS [ 7.969766] zram1: detected capacity change from 0 to 518537216 [ 7.979922] Adding 506380k swap on /dev/zram1. Priority:5 extents:1 across:506380k SS [ 7.988128] zram2: detected capacity change from 0 to 518537216 [ 7.998922] Adding 506380k swap on /dev/zram2. Priority:5 extents:1 across:506380k SS [ 8.005883] zram3: detected capacity change from 0 to 518537216 [ 8.017652] Adding 506380k swap on /dev/zram3. Priority:5 extents:1 across:506380k SS [ 9.036900] nvgpu: 57000000.gpu railgate_enable_store:297 [INFO] railgate is disabled. [ 9.482235] Bridge firewalling registered [ 9.555503] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 9.842092] r8168: eth0: link up [ 9.842599] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9.901000] Netfilter messages via NETLINK v0.30. [ 9.904473] ctnetlink v0.93: registering with nfnetlink. [ 10.347376] tegradc tegradc.0: blank - powerdown [ 10.369304] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready [ 10.398542] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 10.398544] Extcon AUX1(HDMI) disable [ 10.419223] tegradc tegradc.0: unblank [ 10.427587] tegradc tegradc.0: nominal-pclk:369436760 parent:369434375 div:1.0 pclk:369434375 365742333~402686003 [ 10.427684] tegradc tegradc.0: hdmi: tmds rate:369436K prod-setting:prod_c_hdmi_300m_600m [ 10.430482] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 10.498303] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 10.498306] Extcon AUX1(HDMI) enable [ 10.504759] tegradc tegradc.0: unblank [ 10.504768] tegradc tegradc.1: blank - powerdown [ 10.571902] wlan0: authenticate with 18:e8:29:14:52:5f [ 10.583571] wlan0: send auth to 18:e8:29:14:52:5f (try 1/3) [ 10.611642] wlan0: authenticated [ 10.614256] wlan0: associate with 18:e8:29:14:52:5f (try 1/3) [ 10.634915] wlan0: RX AssocResp from 18:e8:29:14:52:5f (capab=0x1431 status=0 aid=3) [ 10.652567] wlan0: associated [ 10.706553] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 15.212235] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 31.858248] vdd-usb-vbus: disabling [ 31.858253] vdd-usb-vbus2: disabling [ 31.858265] vddio-sdmmc3-ap: disabling [ 31.858335] avdd-io-edp-1v05: disabling [ 31.858338] vdd-usb-hub-en: disabling [ 37.077286] tegradc tegradc.0: blank - powerdown [ 37.105331] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 37.105333] Extcon AUX1(HDMI) disable [ 37.118133] tegradc tegradc.1: blank - powerdown [ 37.251675] tegradc tegradc.0: blank - powerdown [ 37.251697] tegradc tegradc.0: unblank [ 37.259886] tegradc tegradc.0: nominal-pclk:369436760 parent:369434375 div:1.0 pclk:369434375 365742333~402686003 [ 37.259978] tegradc tegradc.0: hdmi: tmds rate:369436K prod-setting:prod_c_hdmi_300m_600m [ 37.261374] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 37.332347] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 37.332350] Extcon AUX1(HDMI) enable [ 37.338272] tegradc tegradc.0: unblank [ 37.338561] tegradc tegradc.1: blank - powerdown [ 39.395061] fuse init (API version 7.26) [ 42.019489] tegradc tegradc.0: unblank [ 42.019499] tegradc tegradc.1: blank - powerdown