OPTIONS: I18n Compiled on Nov 15 2018, 20:18:47. Port /dev/ttyUSB0, 15:34:41 Press CTRL-A Z for help on special keys [0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-80a468da) [0000.131] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.139] Power-up reason: pmc por [0000.142] No Battery Present [0000.145] pmic max77620 reset reason [0000.148] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.154] Platform has DDR4 type RAM [0000.157] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x3116eb [0000.173] Entering ramdump check [0000.176] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.189] Sdram initialization is successful [0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.270] Read GPT from (4:0) [0000.514] Csd NumOfBlocks=124735488 [0000.519] Set High speed to 1 [0000.522] Error mask set in wait for cmd complete with error 0x3 in HwSdmmcWai [0000.532] Command complete wait failed with error 0x3 Interrupt 0x18001 [0000.538] Number of retries left 4 [0000.547] Using GPT Primary to query partitions [0000.552] Loading Tboot-CPU binary [0000.562] Verifying TBC in OdmNonSecureSBK mode [0000.572] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.579] Bootloader downloaded successfully. [0000.583] Downloaded Tboot-CPU binary to 0xa0000258 [0000.588] MAX77620_GPIO5 configured [0000.591] CPU power rail is up [0000.594] CPU clock enabled [0000.598] Performing RAM repair [0000.601] Updating A64 Warmreset Address to 0xa00002e9 [0000.606] Loading NvTbootBootloaderDTB [0000.630] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.696] Bootloader DTB Load Address: 0x83000000 [0000.700] Loading NvTbootKernelDTB [0000.724] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.789] Kernel DTB Load Address: 0x83100000 [0000.794] Loading cboot binary [0000.823] Verifying EBT in OdmNonSecureSBK mode [0000.865] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.872] Bootloader downloaded successfully. [0000.877] Read PT from (2:0) [0000.892] Using BFS PT to query partitions [0000.896] PT: Partition NCT NOT found ! [0000.900] Warning: Find Partition via PT Failed [0000.904] Next binary entry address: 0x92c00258 [0000.909] BoardId: 3448 [0000.913] Overriding pmu board id with proc board id [0000.918] Display board id is not available [0000.946] Verifying SC7EntryFw in OdmNonSecureSBK mode [0000.998] /bpmp deleted [0001.000] SC7EntryFw header found loaded at 0xff700000 [0001.190] OVR2 PMIC [0001.192] Bpmp FW successfully loaded [0001.196] WB0 init successfully at 0xff780000 [0001.200] Set NvDecSticky Bits [0001.204] GSC2 address ff53fffc value c0edbbcc [0001.210] GSC MC Settings done [0001.213] TOS Image length 53680 [0001.217] Monitor size 53680 [0001.219] OS size 0 [0001.226] Secure Os AES-CMAC Verification Success! [0001.231] TOS image cipher info: plaintext [0001.235] Loading and Validation of Secure OS Successful [0001.251] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.255] NvTbootPackSdramParams: start. [0001.260] NvTbootPackSdramParams: done. [0001.264] Tegraboot started after 52321 us [0001.268] Basic modules init took 892561 us [0001.272] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB [0001.278] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.283] Storage Device Read Time = 107 ms, Read Size = 2241 KB [0001.289] Storage Device Write Time = 0 ms, Write Size = 0 KB [0001.294] Next stage binary read took 24208 us [0001.299] Carveout took -35891 us [0001.302] CPU initialization took 361637 us [0001.306] Total time taken by TegraBoot 1242515 us [0001.310] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):41d46a9cf NOTICE: BL31: Built : 21:18:12, Jun 25 2020 ERROR: Error initializing runtime service trusty_fast [0001.433] RamCode = 0 [0001.437] LPDDR4 Training: Read DT: Number of tables = 2 [0001.442] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.455] EMC Training Successful [0001.458] 408000 not found in DVFS table [0001.465] RamCode = 0 [0001.468] DT Write: emc-table@204000 succeeded [0001.473] DT Write: emc-table@1600000 succeeded [0001.478] LPDDR4 Training: Write DT: Number of tables = 2 [0001.522] [0001.523] Debug Init done [0001.526] Marked DTB cacheable [0001.529] Bootloader DTB loaded at 0x83000000 [0001.533] Marked DTB cacheable [0001.536] Kernel DTB loaded at 0x83100000 [0001.540] DeviceTree Init done [0001.553] Pinmux applied successfully [0001.557] gicd_base: 0x50041000 [0001.561] gicc_base: 0x50042000 [0001.564] Interrupts Init done [0001.568] Using base:0x60005090 & irq:208 for tick-timer [0001.573] Using base:0x60005098 for delay-timer [0001.578] platform_init_timer: DONE [0001.581] Timer(tick) Init done [0001.585] osc freq = 38400 khz [0001.589] [0001.590] Welcome to L4T Cboot [0001.593] [0001.594] Cboot Version: 00.00.2018.01-t210-3a7ad565 [0001.599] calling constructors [0001.602] initializing heap [0001.605] initializing threads [0001.608] initializing timers [0001.611] creating bootstrap completion thread [0001.615] top of bootstrap2() [0001.618] CPU: ARM Cortex A57 [0001.621] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.626] initializing platform [0001.633] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.638] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.642] Macronix QSPI chip present [0001.646] SPI device register [0001.648] init boot device [0001.651] allocating memory for boot device(SPI) [0001.656] registering boot device [0001.665] sdmmc node status = okay [0001.668] sdcard instance = 0 [0001.671] sdcard gpio handle 0x56 [0001.674] sdcard gpio pin 0xc9 [0001.677] sdcard gpio flags 0x0 [0001.680] vmmc-supply 0x99 [0001.683] Instance: 0 [0001.685] Allocating memory for context [0001.689] enabling clock [0001.691] sd card init [0001.694] Check card present and stable [0001.697] Send command 0 [0001.722] Send command 3 [0001.726] Set RCA for the card [0001.729] Query card specific data by command 9 [0001.735] Parse CSD data [0001.738] Send command 7 [0001.748] Calling sd device register [0001.752] Init sdcard [0001.754] Allocating memory for boot device [0001.758] Registering user device [0001.771] Enable APE clock [0001.774] Un-powergate APE partition [0001.777] of_register: registering tegra_udc to of_hal [0001.782] of_register: registering inv20628-driver to of_hal [0001.788] of_register: registering ads1015-driver to of_hal [0001.793] of_register: registering lp8557-bl-driver to of_hal [0001.799] of_register: registering bq2419x_charger to of_hal [0001.805] of_register: registering bq27441_fuel_gauge to of_hal [0001.816] gpio framework initialized [0001.820] of_register: registering tca9539_gpio to of_hal [0001.825] of_register: registering tca9539_gpio to of_hal [0001.831] of_register: registering i2c_bus_driver to of_hal [0001.836] of_register: registering i2c_bus_driver to of_hal [0001.842] of_register: registering i2c_bus_driver to of_hal [0001.847] pmic framework initialized [0001.851] of_register: registering max77620_pmic to of_hal [0001.856] regulator framework initialized [0001.860] of_register: registering tps65132_bl_driver to of_hal [0001.866] initializing target [0001.872] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.880] board ID = D78, board SKU = 0 [0001.884] Skipping Z3! [0001.888] fixed regulator driver initialized [0001.906] initializing OF layer [0001.909] NCK carveout not present [0001.912] Skipping dts_overrides [0001.916] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.933] I2C Bus Init done [0001.936] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.946] I2C Bus Init done [0001.949] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.959] I2C Bus Init done [0001.962] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.972] I2C Bus Init done [0001.975] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.985] I2C Bus Init done [0001.988] of_children_init: Ops found for compatible string maxim,max77620 [0001.998] max77620_init using irq 118 [0002.003] register 'maxim,max77620' pmic [0002.007] gpio_driver_register: register 'max77620-gpio' driver [0002.014] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.024] I2C Bus Init done [0002.028] NCK carveout not present [0002.038] Find /i2c@7000c000's alias i2c0 [0002.042] get eeprom at 1-a0, size 256, type 0 [0002.050] Find /i2c@7000c500's alias i2c2 [0002.054] get eeprom at 3-a0, size 256, type 0 [0002.059] get eeprom at 3-ae, size 256, type 0 [0002.063] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.068] I2C slave not started [0002.071] I2C write failed [0002.074] Writing offset failed [0002.077] eeprom_init: EEPROM read failed [0002.081] pm_ids_update: eeprom init failed [0002.085] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.115] pm_ids_update: The pm board id is 3448-0000-400 [0002.122] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.130] pm_ids_update: pm id update successful [0002.134] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.164] pm_ids_update: The pm board id is 3449-0000-400 [0002.171] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.179] pm_ids_update: pm id update successful [0002.209] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.215] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.223] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.229] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.238] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:35:ca [0002.244] Plugin Manager: Parse ODM data 0x00094000 [0002.254] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7 [0002.269] Find /i2c@7000c000's alias i2c0 [0002.273] get eeprom at 1-a0, size 256, type 0 [0002.282] Find /i2c@7000c500's alias i2c2 [0002.286] get eeprom at 3-a0, size 256, type 0 [0002.290] get eeprom at 3-ae, size 256, type 0 [0002.294] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.300] I2C slave not started [0002.303] I2C write failed [0002.305] Writing offset failed [0002.308] eeprom_init: EEPROM read failed [0002.312] pm_ids_update: eeprom init failed [0002.316] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.347] pm_ids_update: The pm board id is 3448-0000-400 [0002.353] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.360] pm_ids_update: pm id update successful [0002.365] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.395] pm_ids_update: The pm board id is 3449-0000-400 [0002.401] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.408] pm_ids_update: pm id update successful [0002.439] Add serial number:1423219108126 as DT property [0002.447] Applying platform configs [0002.453] platform-init is not present. Skipping [0002.458] calling apps_init() [0002.483] Found 14 GPT partitions in "sd0" [0002.487] Proceeding to Cold Boot [0002.490] starting app android_boot_app [0002.494] Device state: unlocked [0002.497] display console init [0002.506] could not find regulator [0002.509] hdmi cable connected [0002.524] edid read success [0002.540] edDT entry for leds-pwm not found i[0002.547] d read success [0002.549] width = 640, height = 480, frequency = 25174825 [0002.555] width = 2560, height = 1440, frequency = 241500000 [0002.560] width = 1920, height = 1080, frequency = 148500000 [0002.566] width = 1920, height = 1080, frequency = 148351648 [0002.572] width = 1920, height = 1080, frequency = 148351648 [0002.577] width = 1280, height = 720, frequency = 74175824 [0002.583] width = 1280, height = 720, frequency = 74175824 [0002.588] width = 720, height = 480, frequency = 26973026 [0002.594] width = 720, height = 576, frequency = 26973026 [0002.599] width = 720, height = 480, frequency = 26973026 [0002.604] width = 720, height = 576, frequency = 26973026 [0002.610] width = 640, height = 480, frequency = 25174825 [0002.615] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.623] tmds-config node not found [0002.627] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltageps [0002.642] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.649] could not find regulator [0002.653] could not find regulator [0002.656] could not find regulator [0002.684] using default cmu settings [0002.688] dc_hdmi_enable, starting HDMI initialisation [0002.694] dc_hdmi_enable, HDMI initialisation complete [0002.699] list and configure display window [0002.708] display console init completed [0002.719] subnode volume_up is not found ! [0002.723] subnode back is not found ! [0002.727] subnode volume_down is not found ! [0002.731] subnode menu is not found ! [0002.734] Gpio keyboard init success [0002.778] found decompressor handler: lz4-legacy [0002.793] decompressing blob (type 1)... [0002.828] load_bmp_blob: panelresolution=1080 type=3 [0002.879] decompressor handler not found [0002.883] load_firmware_blob: Firmware blob loaded, entries=2 [0002.888] -------> se_aes_verify_sbk_clear: 747 [0002.893] se_aes_verify_sbk_clear: Error [0002.897] bl_battery_charging: connected to external power supply [0002.904] xusb is supported [0002.910] error while finding nvidia,portmap [0003.414] xusb blob version 0 size 124416 [0003.418] firmware size 124416 [0003.423] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0003.431] xhci0: 64 bytes context size, 32-bit DMA [0003.471] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.491] uhub0: on u0 [0004.141] uhub0: 9 ports with 9 removable, self powered [0005.141] failed to get HID devices [0005.144] failed to init xhci or no usb device attached [0005.155] device_query_partition_size: failed to open partition sd0:MSC ! [0005.161] MSC Partition not found [0005.168] device_query_partition_size: failed to open partition sd0:USP ! [0005.174] USP partition read failed! [0005.178] blob_init: blob-partition USP header read failed [0005.183] android_boot Unable to update recovery partition [0005.189] kfs_getpartname: name = LNX [0005.192] Loading kernel from LNX [0005.291] load kernel from storage [0005.302] decompressor handler not found [0005.360] Successfully loaded kernel and ramdisk images [0005.366] load_bmp_blob: panelresolution=1080 type=3 [0005.862] display bmp image done [0005.865] NCK carveout not present [0005.869] Skipping dts_overrides [0005.872] NCK carveout not present [0005.882] Find /i2c@7000c000's alias i2c0 [0005.886] get eeprom at 1-a0, size 256, type 0 [0005.895] Find /i2c@7000c500's alias i2c2 [0005.898] get eeprom at 3-a0, size 256, type 0 [0005.903] get eeprom at 3-ae, size 256, type 0 [0005.907] pm_ids_update: Updating 1,a0, size 256, type 0 [0005.912] I2C slave not started [0005.915] I2C write failed [0005.918] Writing offset failed [0005.921] eeprom_init: EEPROM read failed [0005.925] pm_ids_update: eeprom init failed [0005.929] pm_ids_update: Updating 3,a0, size 256, type 0 [0005.959] pm_ids_update: The pm board id is 3448-0000-400 [0005.966] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0005.974] pm_ids_update: pm id update successful [0005.978] pm_ids_update: Updating 3,ae, size 256, type 0 [0006.008] pm_ids_update: The pm board id is 3449-0000-400 [0006.015] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0006.023] pm_ids_update: pm id update successful [0006.053] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0006.059] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0006.068] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0006.073] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0006.082] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:35:ca [0006.088] Plugin Manager: Parse ODM data 0x00094000 [0006.099] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7 [0006.107] Add serial number:1423219108126 as DT property [0006.116] "bpmp" doesn't exist, creating [0006.121] Updated bpmp info to DTB [0006.126] Updated initrd info to DTB [0006.130] "proc-board" doesn't exist, creating [0006.135] Updated board info to DTB [0006.138] "pmu-board" doesn't exist, creating [0006.144] Updated board info to DTB [0006.147] "display-board" doesn't exist, creating [0006.153] Updated board info to DTB [0006.156] "reset" doesn't exist, creating [0006.161] Updated reset info to DTB [0006.164] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype [0006.203] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0006.209] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 [0006.222] Updated bootarg info to DTB [0006.225] Adding uuid 000000016445b5090000000007018000 to DT [0006.231] Adding eks info 0 to DT [0006.237] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0006.243] Updated memory info to DTB [0006.251] set vdd_core voltage to 1125 mv [0006.255] setting 'vdd-core' regulator to 1125000 micro volts [0006.281] Found secure-pmc; disable BPMP U-Boot 2016.07-ge6da093be3 (Jun 25 2020 - 21:18:08 -0700) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 844 bytes read in 173 ms (3.9 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 5488163 bytes read in 323 ms (16.2 MiB/s) Retrieving file: /boot/Image 34330632 bytes read in 1536 ms (21.3 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resiz ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 00000000831777a1 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-3456) (gcc ve0 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92cb4000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.082116] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.247300] imx219 7-0010: imx219_board_setup: error during i2c read probe () [ 1.247332] imx219 7-0010: board setup failed [ 1.271151] imx219 8-0010: imx219_board_setup: error during i2c read probe () [ 1.271179] imx219 8-0010: board setup failed [ 2.276684] cgroup: cgroup2: unknown option "nsdelegate" [ 3.194895] nvgpu: disagrees about version of symbol module_layout [ 3.308110] spidev: disagrees about version of symbol module_layout [ 3.316134] spidev: disagrees about version of symbol module_layout [ 3.317569] spidev: disagrees about version of symbol module_layout [ 3.319120] spidev: disagrees about version of symbol module_layout [ 3.628412] tegra_udrm: disagrees about version of symbol module_layout [ 3.733244] random: crng init done [ 3.738851] random: 7 urandom warning(s) missed due to ratelimiting [ 3.829360] using random self ethernet address [ 3.837426] using random host ethernet address [ 4.173755] using random self ethernet address [ 4.180389] using random host ethernet address [ 7.723786] zram: disagrees about version of symbol module_layout