ÿâ [0000.084] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0000.093] I> MB1 (prd-version: 1.5.1.3-t194-41334769-d2a21c57) [0000.098] I> Boot-mode: Coldboot [0000.101] I> Chip revision : A02P [0000.104] I> Bootrom patch version : 15 (correctly patched) [0000.110] I> ATE fuse revision : 0x200 [0000.113] I> Ram repair fuse : 0x0 [0000.116] I> Ram Code : 0x2 [0000.119] I> rst_source : 0x0 [0000.121] I> rst_level : 0x0 [0000.125] I> Boot-device: eMMC [0000.140] I> sdmmc DDR50 mode [0000.144] W> No valid slot number is found in scratch register [0000.149] W> Return default slot: _a [0000.153] I> Active Boot chain : 0 [0000.156] I> Boot-device: eMMC [0000.159] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.167] I> Temperature = 39000 [0000.170] W> Skipping boost for clk: BPMP_CPU_NIC [0000.175] W> Skipping boost for clk: BPMP_APB [0000.179] W> Skipping boost for clk: AXI_CBB [0000.183] W> Skipping boost for clk: AON_CPU_NIC [0000.187] W> Skipping boost for clk: CAN1 [0000.191] W> Skipping boost for clk: CAN2 [0000.195] I> Boot-device: eMMC [0000.198] I> Boot-device: eMMC [0000.207] I> Sdmmc: HS400 mode enabled [0000.212] I> ECC region[0]: Start:0x0, End:0x0 [0000.216] I> ECC region[1]: Start:0x0, End:0x0 [0000.220] I> ECC region[2]: Start:0x0, End:0x0 [0000.224] I> ECC region[3]: Start:0x0, End:0x0 [0000.228] I> ECC region[4]: Start:0x0, End:0x0 [0000.232] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.238] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.242] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.247] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.251] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.257] E> FAILED: Thermal config [0000.264] E> FAILED: MEMIO rail config [0000.283] I> Boot-device: eMMC [0000.292] I> sdmmc bdev is already initialized [0000.363] I> MB1 done ÿýÿàmain enter SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init ÿâ [0000.371] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-aa987a31) [0000.372] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0000.373] I> Default Heap @ [0xd486400 - 0xd48a400] [0000.373] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0000.379] W> device prod register failed [0000.383] I> Boot-device: eMMC [0000.386] I> Boot_device: SDMMC_BOOT instance: 3 [0000.392] I> sdmmc-3 params source = boot args [0000.394] I> sdmmc bdev is already initialized [0000.399] I> sdmmc-3 params source = boot args [0000.405] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0000.412] I> Found 42 partitions in SDMMC_USER (instance 3) [0000.414] W> No valid slot number is found in scratch register [0000.420] W> Return default slot: _a [0000.423] I> Active Boot chain : 0 [0000.427] I> parsing oem signed section of bpmp-fw header done [0000.432] I> bpmp-fw binary init read from storage [0000.437] I> oem authentication of bpmp-fw header done [0000.444] I> bpmp-fw binary done read from storage [0000.446] I> bpmp-fw: Authentication init Done [0000.451] I> parsing oem signed section of cpubl header done [0000.456] I> cpubl binary init read from storage [0000.461] I> bpmp-fw: Authentication Finalize Done [0000.465] I> oem authentication of cpubl header done [0000.470] I> cpubl binary done read from storage [0000.474] I> cpubl: Authentication init Done [0000.479] I> parsing oem signed section of rce header done [0000.484] I> rce binary init read from storage [0000.488] I> Relocating BR-BCT [0000.491] I> cpubl: Authentication Finalize Done [0000.496] I> oem authentication of rce header done [0000.500] I> rce binary done read from storage [0000.504] I> rce: Authentication init Done [0000.509] I> parsing oem signed section of ape header done [0000.514] I> ape binary init read from storage [0000.518] I> rce: Authentication Finalize Done [0000.523] I> oem authentication of ape header done [0000.527] I> ape binary done read from storage [0000.531] I> ape: Authentication init Done [0000.537] I> parsing oem signed section of tos header done [0000.541] I> tos binary init read from storage [0000.545] I> ape: Authentication Finalize Done [0000.550] I> oem authentication of tos header done [0000.554] I> tos binary done read from storage [0000.558] I> tos: Authentication init Done [0000.563] I> parsing oem signed section of bpmp-fw-dtb header done [0000.568] I> bpmp-fw-dtb binary init read from storage [0000.573] I> tos: Authentication Finalize Done [0000.579] I> oem authentication of bpmp-fw-dtb header done [0000.585] I> bpmp-fw-dtb binary done read from storage [0000.588] I> bpmp-fw-dtb: Authentication init Done [0000.593] I> parsing oem signed section of cpubl-dtb header done [0000.598] I> cpubl-dtb binary init read from storage [0000.603] I> bpmp-fw-dtb: Authentication Finalize Done [0000.640] I> oem authentication of cpubl-dtb header done [0000.641] I> cpubl-dtb binary done read from storage [0000.641] I> cpubl-dtb: Authentication init Done [0000.643] I> parsing oem signed section of eks header done [0000.644] I> eks binary init read from storage [0000.645] I> cpubl-dtb: Authentication Finalize Done [0000.645] I> oem authentication of eks header done [0000.649] I> eks binary done read from storage [0000.653] I> eks: Authentication init Done [0000.657] I> eks: Authentication Finalize Done [0000.661] I> EKB detected (length: 0x410) @ VA:0x5270a400 ÿäNOTICE: BL31: v1.3(release):fe06da916 NOTICE: BL31: Built : 18:06:49, Apr 8 2020 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 40: hwkey-agent is running!! hwkey-agent: 182: key_mgnt_processing ....... hwkey-agent: 157: Init hweky-agent services!! platform_bootstrap_epilog: trusty bootstrap complete ÿâ welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is 57f8a77779f848bf2ecf21dabee5645f tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized 392 clocks registered WARNING: pll_c4 has no dyn ramp clk_mrq_init: mrq handler registered clk initialized nvlink initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized uphy_mrq_init: mrq handler registered uphy_dt initialized uphy initialized safereg_init: period 80 ms ec_late initialized mrq initialized ÿá [0001.165] I> Welcome to Cboot ÿâfmon_post initialized ÿá[0001.166] I> Cboot Version: t194-d00c695c [0001.166] I> CPU-BL Params @ 0xf2820000 [0001.166] I> 0) Base:0x00000000 Size:0x00000000 [0001.170] I> 1) Base:0xf1100000 Size:0x00100000 [0001.174] I> 2) Base:0xf2000000 Size:0x00200000 [0001.179] I> 3) Base:0xf1200000 Size:0x00200000 [0001.183] I> 4) Base:0xf1000000 Size:0x00100000 [0001.188] I> 5) Base:0xf0f00000 Size:0x00100000 ÿâclk_dt_late initialized machine_check initialized pm_post initialized dbells initialized avfs_clk_platform_post initialized dmce initialized cvc initialized ccplex_avfs_hw_init: nafll_cluster0: not monitored ccplex_avfs_hw_init: nafll_cluster1: not monitored ccplex_avfs_hw_init: nafll_cluster2: not monitored ccplex_avfs_hw_init: nafll_cluster3: not monitored avfs_clk_mach_post initialized regulator_post initialized rm initialized sc7_diag initialized thermal_test initialized serial_late initialized clk_post initialized clk_dt_post initialized mc_reg initialized pg_post initialized dyn_modules initialized sku_debugfs initialized speedo_debugfs initialized adc_debugfs initialized clk_debugfs initialized ÿá[0001.192] I> 6) Base:0xf3800000 Size:0x00400000 [0001.261] I> 7) Base:0xf1c00000 Size:0x00400000 [0001.266] I> 8) Base:0xf0e00000 Size:0x00100000 [0001.270] I> 9) Base:0xf0d00000 Size:0x00100000 [0001.275] I> 10) Base:0xf3000000 Size:0x00800000 [0001.279] I> 11) Base:0x40000000 Size:0x00040000 [0001.284] I> 12) Base:0xf0c00000 Size:0x00100000 [0001.288] I> 13) Base:0x40046000 Size:0x00002000 [0001.293] I> 14) Base:0x40048000 Size:0x00002000 [0001.297] I> 15) Base:0xac000000 Size:0x00004000 [0001.302] I> 16) Base:0x4004a000 Size:0x00002000 [0001.306] I> 17) Base:0xf0b00000 Size:0x00100000 ÿâemc_debugfs initialized dvs_debugfs initialized fmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized debugfs_cons initialized mail_fs initialized profile initialized cvc_debugfs initialized dmce_debugfs initialized ec_debugfs initialized rm_debugfs initialized soctherm_debug initialized gr_reader initialized mods initialized dt_fs initialized debugfs_mrq initialized debug_mrq initialized debug_safereg initialized initializing target calling apps_init() starting app shell entering main console loop ] ÿá[0001.311] I> 18) Base:0x4004c000 Size:0x00002000 [0001.365] I> 19) Base:0xf2200000 Size:0x00600000 [0001.370] I> 20) Base:0x4004e000 Size:0x00002000 [0001.374] I> 21) Base:0xf09d0000 Size:0x0000c000 [0001.379] I> 22) Base:0x00000000 Size:0x00000000 [0001.383] I> 23) Base:0xf09e0000 Size:0x00020000 [0001.388] I> 24) Base:0xf6000000 Size:0x02000000 [0001.392] I> 25) Base:0x40050000 Size:0x00002000 [0001.397] I> 26) Base:0x40040000 Size:0x00006000 [0001.401] I> 27) Base:0xf1800000 Size:0x00400000 [0001.406] I> 28) Base:0xf4c00000 Size:0x01400000 [0001.410] I> 29) Base:0xf1400000 Size:0x00400000 [0001.414] I> 30) Base:0xf0a00000 Size:0x00100000 [0001.419] I> 31) Base:0x00000000 Size:0x00000000 [0001.423] I> 32) Base:0xf8000000 Size:0x08000000 [0001.428] I> 33) Base:0x00000000 Size:0x00000000 [0001.432] I> 34) Base:0xf3c00000 Size:0x01000000 [0001.437] I> 35) Base:0xab000000 Size:0x01000000 [0001.441] I> 36) Base:0xa0000000 Size:0x0b000000 [0001.446] I> 37) Base:0xf2800000 Size:0x00800000 [0001.450] I> 38) Base:0x80000000 Size:0x20000000 [0001.455] I> 39) Base:0xb0000000 Size:0x08000000 [0001.459] I> 40) Base:0x00000000 Size:0x00000000 [0001.464] I> 41) Base:0x00000000 Size:0x00000000 [0001.468] I> 42) Base:0x00000000 Size:0x00000000 [0001.472] I> 43) Base:0x00000000 Size:0x00000000 [0001.477] I> 44) Base:0x00000000 Size:0x00000000 [0001.481] I> 45) Base:0x00000000 Size:0x00000000 [0001.486] GIC-SPI Target CPU: 0 [0001.489] Interrupts Init done [0001.492] calling constructors [0001.495] initializing heap [0001.497] I> Heap: [0xa06905a8 ... 0xab000000] [0001.502] initializing threads [0001.504] initializing timers [0001.507] creating bootstrap completion thread [0001.512] top of bootstrap2() [0001.514] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000 [0001.519] initializing platform [0001.522] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0001.527] W> device prod register failed [0001.531] I> Bl_dtb @0xaaf00000 [0001.537] E> "plugin-manager" doesn't exist, creating [0001.539] E> "ids" doesn't exist, creating [0001.543] E> "connection" doesn't exist, creating [0001.548] E> "configs" doesn't exist, creating [0001.559] I> Find /i2c@3160000's alias i2c0 [0001.559] I> Reading eeprom i2c=0 address=0x50 [0001.585] I> Device at /i2c@3160000:0x50 [0001.586] I> Reading eeprom i2c=0 address=0x56 [0001.610] I> Device at /i2c@3160000:0x56 [0001.612] I> Find /i2c@3180000's alias i2c2 [0001.612] I> Reading eeprom i2c=2 address=0x54 [0001.614] E> I2C: slave not found in slaves. [0001.614] E> I2C: Could not write 0 bytes to slave: 0x00a8 with repeat start true. [0001.615] E> I2C_DEV: Failed to send register address 0x00000000. [0001.616] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa8 at 0x00000000 via instance 2. [0001.624] E> eeprom: Failed to read I2C slave device [0001.629] I> Eeprom read failed 0x3526070d [0001.633] I> Reading eeprom i2c=2 address=0x57 [0001.637] E> I2C: slave not found in slaves. [0001.641] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0001.649] E> I2C_DEV: Failed to send register address 0x00000000. [0001.655] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 2. [0001.664] E> eeprom: Failed to read I2C slave device [0001.669] I> Eeprom read failed 0x3526070d [0001.673] I> Reading eeprom i2c=2 address=0x52 [0001.677] E> I2C: slave not found in slaves. [0001.681] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.689] E> I2C_DEV: Failed to send register address 0x00000000. [0001.695] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 2. [0001.704] E> eeprom: Failed to read I2C slave device [0001.709] I> Eeprom read failed 0x3526070d [0001.715] I> Find /i2c@c240000's alias i2c1 [0001.717] I> Reading eeprom i2c=1 address=0x52 [0001.723] E> I2C: slave not found in slaves. [0001.725] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.733] E> I2C_DEV: Failed to send register address 0x00000000. [0001.739] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.748] E> eeprom: Retry to read I2C slave device. [0001.753] E> I2C: slave not found in slaves. [0001.757] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.765] E> I2C_DEV: Failed to send register address 0x00000000. [0001.771] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.780] E> eeprom: Failed to read I2C slave device [0001.785] I> Eeprom read failed 0x3526070d [0001.789] I> Reading eeprom i2c=1 address=0x50 [0001.793] E> I2C: slave not found in slaves. [0001.797] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.805] E> I2C_DEV: Failed to send register address 0x00000000. [0001.811] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.820] E> eeprom: Retry to read I2C slave device. [0001.825] E> I2C: slave not found in slaves. [0001.829] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.837] E> I2C_DEV: Failed to send register address 0x00000000. [0001.843] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.852] E> eeprom: Failed to read I2C slave device [0001.857] I> Eeprom read failed 0x3526070d [0001.861] I> create_pm_ids: id: 2888-0004-400-K, len: 15 [0001.866] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.877] I> create_pm_ids: id: 2822-0000-700-J, len: 15 [0001.882] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.893] I> Adding plugin-manager/ids/2888-0004-400=/i2c@3160000:module@0x50 [0001.901] E> "i2c@3160000" doesn't exist, creating [0001.905] E> "module@0x50" doesn't exist, creating [0001.910] I> Adding plugin-manager/ids/2822-0000-700=/i2c@3160000:module@0x56 [0001.917] E> "module@0x56" doesn't exist, creating [0001.923] I> Adding plugin-manager/cvm [0001.925] E> "chip-id" doesn't exist, creating [0001.929] I> Adding plugin-manager/chip-id/A02P [0001.934] I> Plugin-manager override starting [0001.939] I> node /plugin-manager/fragement-tegra-wdt-en matches [0001.948] I> node /plugin-manager/fragement-soft-wdt matches [0001.955] I> node /plugin-manager/fragment-pcie-c5-rp matches [0001.959] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0001.969] I> Disable plugin-manager status in FDT [0001.969] I> Plugin-manager override finished successfully [0001.971] I> gpio framework initialized [0001.975] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver [0001.983] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver [0001.989] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 [0001.997] E> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.005] E> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.011] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.017] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 [0002.025] E> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.033] E> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.039] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.047] I> fixed regulator driver initialized [0002.058] I> register 'maxim' power off handle [0002.058] I> virtual i2c enabled [0002.059] I> registered 'maxim,max20024' pmic [0002.061] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver [0002.068] I> Boot-device: eMMC [0002.070] I> Boot_device: SDMMC_BOOT instance: 3 [0002.079] I> sdmmc-3 params source = boot args [0002.079] I> create_pm_ids: id: 2888-0004-400-K, len: 15 [0002.084] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.095] I> create_pm_ids: id: 2822-0000-700-J, len: 15 [0002.101] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.112] I> sdmmc bdev is already initialized [0002.116] I> sdmmc-3 params source = boot args [0002.147] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0002.159] I> Found 42 partitions in SDMMC_USER (instance 3) [0002.171] I> enabling 'vdd-hdmi-5v0' regulator [0002.176] I> regulator 'vdd-hdmi-5v0' already enabled [0002.176] I> hdmi cable connected [0002.178] E> set volts not configured for 'vdd-1v0' [0002.180] E> set volts not configured for 'vdd-1v8-hs' [0002.184] E> invalid display type [0002.187] E> invalid display type [0002.189] E> cannot find any other nvdisp nodes [0002.204] I> edid read success [0002.204] I> width = 1024, height = 600, frequency = 49000000 [0002.205] I> Best mode Width = 640, Height = 480, freq = 25174825 [0002.209] I> hdmi_enable, starting HDMI initialisation [0002.213] I> hdmi_enable, HDMI initialisation complete [0002.216] I> Load in CBoot Boot Options partition and parse it [0002.216] E> Cannot read beyond partition boundary for CPUBL-CFG [0002.217] E> tegrabl_read_cbo Failed to read CPUBL-CFG partition [0002.221] W> platform_init: tegrabl_read_cbo failed with error 0xd0d0104 [0002.228] I> Hit any key to stop autoboot: 4 3 2 1 [0004.235] initializing target [0004.235] calling apps_init() [0004.236] starting app kernel_boot_app [0004.255] I> found decompressor handler: lz4-legacy [0004.256] I> decompressing BMP blob ... [0004.260] I> Kernel type = Normal [0004.260] I> Loading kernel-bootctrl from partition [0004.260] I> Loading partition kernel-bootctrl at 0xa4400000 from device(0x1) [0004.267] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0004.267] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0004.268] I> ########## SD boot ########## [0004.272] I> No sdcard [0004.274] I> -0 params source = [0004.277] E> Blockdev open: exit error [0004.280] E> SD boot failed, err: 724238353 [0004.284] I> ########## USB boot ########## [0004.293] W> No valid slot number is found in scratch register [0004.294] W> Return default slot: _a [0004.310] I> USB Firmware Version: 60.06 release [0004.366] I> regulator of usb2-0 already enabled [0004.372] I> regulator of usb2-1 already enabled [0004.379] I> regulator of usb2-2 already enabled [0004.387] I> enabling 'vdd-5v-sata' regulator [0005.455] I> USB 2.0 port 4 new high-speed USB device detected [0005.456] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa07df800, cmd_ring.dma = 0xa07df840 [0005.457] E> slot id is 1 [0005.458] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa07df800, cmd_ring.dma = 0xa07df840 [0005.463] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa07df800, cmd_ring.dma = 0xa07df840 [0005.467] I> [0005.468] I> Enumerated USB Device 05e3:0610 [0005.472] I> [0005.473] E> Enumerated device doesn't belong to MSD class or protocol is not bulk-only!! [0005.481] E> USBMSD: Failed to initialize Enumerated USB device either not an MSD device or supported protoco[0005.491] E> USBMSD: Failed to open usbmsd open, 0. [0005.496] E> Error opening USBMSD driver 0, err: 7c7c0312 [0005.501] E> Failed to initialize device 5-0 [0005.505] E> USB boot failed, err: 2088502034 [0005.509] I> ########## Fixed storage boot ########## [0005.514] I> Already published: 00010003 [0005.518] I> Look for boot partition [0005.521] I> Fallback: assuming 0th partition is boot partition [0005.527] I> Detect filesystem [0005.554] I> Loading extlinux.conf ... [0005.555] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf [0005.591] I> L4T boot options [0005.592] I> [1]: "primary kernel" [0005.592] I> Enter choice: [0008.593] I> Continuing with default option: 1 [0008.593] I> Loading kernel sig file from rootfs ... [0008.593] I> rootfs path: /sdmmc_user/boot/Image.sig [0008.618] I> Loading kernel binary from rootfs ... [0008.618] I> rootfs path: /sdmmc_user/boot/Image [0008.862] I> Validate kernel ... [0008.862] I> T19x: Authenticate kernel (bin_type: 37), max size 0x5000000 [0009.191] I> No kernel-dtb binary path [0009.191] W> No valid slot number is found in scratch register [0009.191] W> Return default slot: _a [0009.192] I> A/B: bin_type (38) slot 0 [0009.192] I> Loading kernel-dtb from partition [0009.192] I> Loading partition kernel-dtb at 0x91000000 from device(0x1) [0009.201] I> Validate kernel-dtb ... [0009.201] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x400000 [0009.206] I> Loading ramdisk from rootfs ... [0009.207] I> rootfs path: /sdmmc_user/boot/initrd [0009.259] I> Kernel hdr @0xa4400000 [0009.260] I> Kernel dtb @0x90000000 [0009.260] I> decompressor handler not found [0009.260] I> Copying kernel image (34265104 bytes) from 0xa4400000 to 0x80080000 ... [0009.271] I> Done [0009.272] I> Updated bpmp info to DTB [0009.273] I> Ramdisk: Base: 0x92000000; Size: 0x54ec8f [0009.273] I> Updated initrd info to DTB [0009.273] W> WARN: Fail to override "console=none" in commandline [0009.274] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0009.280] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0009.287] W> No valid slot number is found in scratch register [0009.293] W> Return default slot: _a [0009.296] I> Active slot suffix: [0009.299] I> add_boot_slot_suffix: slot_suffix = [0009.304] I> Linux Cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyTCU0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 rootfstype=ext4 video=tegrafb no_console_suspend=1 earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt tegra_fbmem=0x140000@0xa069c000 lut_mem=0x2008@0xa0696000 usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=8 boot.slot_suffix= boot.ratchetvalues=0.4.2 vpr_resize sdhci_tegra.en_boot_part_access=1 [0009.343] I> Updated bootarg info to DTB [0009.346] W> MAC addr invalid! [0009.349] E> Failed to get WIFI MAC address [0009.353] W> MAC addr invalid! [0009.356] E> Failed to get Bluetooth MAC address [0009.361] I> eeprom_get_mac_addr: MAC (type: 2): 48:b0:2d:05:b9:f6 [0009.367] E> "plugin-manager" doesn't exist, creating [0009.372] I> Adding /chosen/plugin-manager/cvm [0009.376] E> "chip-id" doesn't exist, creating [0009.380] I> Adding /chosen/plugin-manager/chip-id [0009.385] E> "configs" doesn't exist, creating [0009.389] I> Adding /chosen/plugin-manager/configs [0009.394] E> "ids" doesn't exist, creating [0009.398] I> Adding /chosen/plugin-manager/ids [0009.402] E> "odm-data" doesn't exist, creating [0009.406] I> Adding /chosen/plugin-manager/odm-data [0009.414] E> "memory" doesn't exist, creating [0009.416] I> [0] START: 0x80000000, END: 0xac000000 [0009.420] I> [1] START: 0xac004000, END: 0xf09d0000 [0009.425] I> [2] START: 0xf09dc000, END: 0xf09e0000 [0009.429] I> dram_block larger than 80000000 [0009.434] I> [3] START: 0x100000000, END: 0x880000000 [0009.438] I> added [base:0x80000000, size:0x2c000000] to /memory [0009.444] I> added [base:0xac200000, size:0x44600000] to /memory [0009.450] I> added [base:0x100000000, size:0x780000000] to /memory [0009.457] I> Updated memory info to DTB [0009.460] E> add_disp_param: failed to get display params for du=1 [0009.466] E> "reset" doesn't exist, creating [0009.471] I> NVG: Logical CPU: 0; MPIDR: 0x80000000 [0009.475] I> NVG: Logical CPU: 1; MPIDR: 0x80000001 [0009.480] I> NVG: Logical CPU: 2; MPIDR: 0x80000100 [0009.484] I> NVG: Logical CPU: 3; MPIDR: 0x80000101 [0009.489] I> NVG: Logical CPU: 4; MPIDR: 0x80000200 [0009.494] I> NVG: Logical CPU: 5; MPIDR: 0x80000201 [0009.498] I> NVG: Logical CPU: 6; MPIDR: 0x80000300 [0009.503] I> NVG: Logical CPU: 7; MPIDR: 0x80000301 [0009.509] E> "misc-data" doesn't exist, creating [0009.512] I> Boot-device: eMMC [0009.515] I> Add boot-sdmmc to plugin-manager/misc-data [0009.520] I> Add storage-sdmmc to plugin-manager/misc-data [0009.526] W> Unknown storage device [0009.530] I> Add serial number:1421420015214 as DT property [0009.536] I> Plugin-manager override starting [0009.539] I> node /plugin-manager/fragement-tegra-wdt-en matches [0009.546] I> node /plugin-manager/fragement-soft-wdt matches [0009.553] I> node /plugin-manager/fragment-pcie-c5-rp matches [0009.558] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0009.569] I> Disable plugin-manager status in FDT [0009.570] I> Plugin-manager override finished successfully [0009.572] I> tegrabl_load_kernel_and_dtb: Done [0009.581] I> Kernel EP: 0x80080000, DTB: 0x90000000 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-3193) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Wed Apr 8 18:15:20 PDT 2020 [ 0.000000] Boot CPU: AArch64 Processor [4e0f0040] [ 0.000000] OF: fdt:memory scan node memory, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 2c000000 [ 0.000000] OF: fdt: - ac200000 , 44600000 [ 0.000000] OF: fdt: - 100000000 , 780000000 [ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '') [ 0.000000] bootconsole [tegra_comb_uart0] enabled [ 0.000000] Found tegra_fbmem: 00140000@a069c000 [ 0.000000] Found lut_mem: 00002008@a0696000 [ 1.963484] tegradc 15200000.nvdisplay: hdmi: edid read failed ÿâWARNING: pll_d3 has no dyn ramp ÿá[ 5.820362] cgroup: cgroup2: unknown option "nsdelegate" [ 6.930276] using random self ethernet address [ 6.930469] using random host ethernet address [ 6.996752] FAT-fs (loop0): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 7.290437] random: crng init done [ 7.290554] random: 7 urandom warning(s) missed due to ratelimiting [ 7.342021] using random self ethernet address [ 7.342156] using random host ethernet address [ 8.024959] CPU4: shutdown [ 8.105052] CPU5: shutdown [ 8.156866] CPU6: shutdown [ 8.213116] CPU7: shutdown Ubuntu 18.04.4 LTS jetson1 ttyTCU0 jetson1 login: