[17:38:53:095] <break>
[17:38:53:218] [0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb)␍␊
[17:38:53:224] [0000.130] Processing in cold boot mode Bootloader 2␍␊
[17:38:53:226] [0000.135] A02 Bootrom Patch rev = 1023␍␊
[17:38:53:232] [0000.138] Power-up reason: pmc por␍␊
[17:38:53:235] [0000.141] No Battery Present␍␊
[17:38:53:238] [0000.144] pmic max77620 reset reason␍␊
[17:38:53:240] [0000.147] pmic max77620 NVERC : 0x40␍␊
[17:38:53:243] [0000.151] RamCode = 0␍␊
[17:38:53:246] [0000.153] Platform has DDR4 type RAM␍␊
[17:38:53:249] [0000.156] max77620 disabling SD1 Remote Sense␍␊
[17:38:53:255] [0000.161] Setting DDR voltage to 1125mv␍␊
[17:38:53:258] [0000.165] Serial Number of Pmic Max77663: 0x51ee8␍␊
[17:38:53:267] [0000.172] Entering ramdump check␍␊
[17:38:53:270] [0000.175] Get RamDumpCarveOut = 0x0␍␊
[17:38:53:273] [0000.178] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8␍␊
[17:38:53:278] [0000.184] Last reboot was clean, booting normally!␍␊
[17:38:53:281] [0000.188] Sdram initialization is successful ␍␊
[17:38:53:287] [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000␍␊
[17:38:53:293] [0000.198] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000␍␊
[17:38:53:298] [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000␍␊
[17:38:53:304] [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000␍␊
[17:38:53:310] [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000␍␊
[17:38:53:316] [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000␍␊
[17:38:53:323] [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000␍␊
[17:38:53:328] [0000.233] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000␍␊
[17:38:53:346] [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000␍␊
[17:38:53:352] [0000.256] Platform-DebugCarveout: 0␍␊
[17:38:53:357] [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000␍␊
[17:38:53:363] [0000.265] Non secure mode, and RB not enabled.␍␊
[17:38:53:370] [0000.269] BoardID = 3448, SKU = 0x0␍␊
[17:38:53:370] [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0␍␊
[17:38:53:380] [0000.276] Nano-SD: checking PT table on QSPI ...␍␊
[17:38:53:380] [0000.280] Initialize FailControl␍␊
[17:38:53:380] [0000.283] Read PT from (2:0)␍␊
[17:38:53:412] [0000.314] PT crc32 and magic check passed.␍␊
[17:38:53:415] [0000.318] Using BFS PT to query partitions ␍␊
[17:38:53:427] [0000.324] Loading Tboot-CPU binary␍␊
[17:38:53:451] [0000.352] Verifying TBC in OdmNonSecureSBK mode␍␊
[17:38:53:461] [0000.362] Bootloader load address is 0xa0000000, entry address is 0xa0000258␍␊
[17:38:53:467] [0000.369] Bootloader downloaded successfully.␍␊
[17:38:53:471] [0000.373] Downloaded Tboot-CPU binary to 0xa0000258␍␊
[17:38:53:477] [0000.378] MAX77620_GPIO5 configured␍␊
[17:38:53:482] [0000.381] CPU power rail is up␍␊
[17:38:53:482] [0000.384] CPU clock enabled␍␊
[17:38:53:487] [0000.388] Performing RAM repair␍␊
[17:38:53:492] [0000.391] Updating A64 Warmreset Address to 0xa00002e9␍␊
[17:38:53:497] [0000.396] BoardID = 3448, SKU = 0x0␍␊
[17:38:53:497] [0000.399] QSPI-ONLY: SkipQspiOnlyFlag = 0␍␊
[17:38:53:503] [0000.403] Nano-SD: checking PT table on QSPI ...␍␊
[17:38:53:508] [0000.407] NvTbootFailControlDoFailover: No failover; Continuing ...␍␊
[17:38:53:518] [0000.413] Loading NvTbootBootloaderDTB␍␊
[17:38:53:582] [0000.480] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode␍␊
[17:38:53:655] [0000.551] Bootloader DTB Load Address: 0x83000000␍␊
[17:38:53:658] [0000.556] BoardID = 3448, SKU = 0x0␍␊
[17:38:53:663] [0000.559] QSPI-ONLY: SkipQspiOnlyFlag = 0␍␊
[17:38:53:669] [0000.563] Nano-SD: checking PT table on QSPI ...␍␊
[17:38:53:676] [0000.567] NvTbootFailControlDoFailover: No failover; Continuing ...␍␊
[17:38:53:676] [0000.573] Loading NvTbootKernelDTB␍␊
[17:38:53:745] [0000.639] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode␍␊
[17:38:53:818] [0000.711] Kernel DTB Load Address: 0x83100000␍␊
[17:38:53:821] [0000.715] BoardID = 3448, SKU = 0x0␍␊
[17:38:53:828] [0000.718] QSPI-ONLY: SkipQspiOnlyFlag = 0␍␊
[17:38:53:834] [0000.722] Nano-SD: checking PT table on QSPI ...␍␊
[17:38:53:834] [0000.726] NvTbootFailControlDoFailover: No failover; Continuing ...␍␊
[17:38:53:848] [0000.734] Loading cboot binary␍␊
[17:38:53:961] [0000.850] Verifying EBT in OdmNonSecureSBK mode␍␊
[17:38:54:004] [0000.892] Bootloader load address is 0x92c00000, entry address is 0x92c00258␍␊
[17:38:54:009] [0000.899] Bootloader downloaded successfully.␍␊
[17:38:54:014] [0000.903] BoardID = 3448, SKU = 0x0␍␊
[17:38:54:019] [0000.906] QSPI-ONLY: SkipQspiOnlyFlag = 0␍␊
[17:38:54:025] [0000.910] Nano-SD: checking PT table on QSPI ...␍␊
[17:38:54:029] [0000.914] NvTbootFailControlDoFailover: No failover; Continuing ...␍␊
[17:38:54:035] [0000.921] PT: Partition NCT NOT found ! ␍␊
[17:38:54:040] [0000.924] Warning: Find Partition via PT Failed␍␊
[17:38:54:044] [0000.928] Next binary entry address: 0x92c00258 ␍␊
[17:38:54:044] [0000.933] BoardId: 3448␍␊
[17:38:54:054] [0000.938] Overriding pmu board id with proc board id␍␊
[17:38:54:054] [0000.942] Display board id is not available ␍␊
[17:38:54:060] [0000.947] BoardID = 3448, SKU = 0x0␍␊
[17:38:54:066] [0000.950] QSPI-ONLY: SkipQspiOnlyFlag = 0␍␊
[17:38:54:066] [0000.954] Nano-SD: checking PT table on QSPI ...␍␊
[17:38:54:072] [0000.958] NvTbootFailControlDoFailover: No failover; Continuing ...␍␊
[17:38:54:181] [0001.065] Verifying SC7EntryFw in OdmNonSecureSBK mode␍␊
[17:38:54:238] [0001.121] /bpmp deleted␍␊
[17:38:54:238] [0001.123] SC7EntryFw header found loaded at 0xff700000␍␊
[17:38:54:433] [0001.311] OVR2 PMIC␍␊
[17:38:54:433] [0001.313] Bpmp FW successfully loaded␍␊
[17:38:54:441] [0001.316] BoardID = 3448, SKU = 0x0␍␊
[17:38:54:447] [0001.320] QSPI-ONLY: SkipQspiOnlyFlag = 0␍␊
[17:38:54:447] [0001.323] Nano-SD: checking PT table on QSPI ...␍␊
[17:38:54:452] [0001.328] NvTbootFailControlDoFailover: No failover; Continuing ...␍␊
[17:38:54:457] [0001.335] WB0 init successfully at 0xff780000␍␊
[17:38:54:462] [0001.339] Verifying NvTbootWb0 in OdmNonSecureSBK mode␍␊
[17:38:54:467] [0001.344] Set NvDecSticky Bits␍␊
[17:38:54:472] [0001.348] GSC2 address ff53fffc value c0edbbcc␍␊
[17:38:54:478] [0001.354] GSC MC Settings done␍␊
[17:38:54:482] [0001.357] BoardID = 3448, SKU = 0x0␍␊
[17:38:54:487] [0001.360] QSPI-ONLY: SkipQspiOnlyFlag = 0␍␊
[17:38:54:487] [0001.364] Nano-SD: checking PT table on QSPI ...␍␊
[17:38:54:492] [0001.368] NvTbootFailControlDoFailover: No failover; Continuing ...␍␊
[17:38:54:498] [0001.375] TOS Image length 53680␍␊
[17:38:54:506] [0001.378]  Monitor size 53680␍␊
[17:38:54:506] [0001.381]  OS size 0␍␊
[17:38:54:520] [0001.396] Secure Os AES-CMAC Verification Success!␍␊
[17:38:54:523] [0001.401] TOS image cipher info: plaintext␍␊
[17:38:54:530] [0001.405] Loading and Validation of Secure OS Successful␍␊
[17:38:54:545] [0001.421] SC7 Entry Firmware - 0xff700000, 0x4000␍␊
[17:38:54:548] [0001.425] NvTbootPackSdramParams: start. ␍␊
[17:38:54:559] [0001.430] NvTbootPackSdramParams: done. ␍␊
[17:38:54:559] [0001.434] Tegraboot started after 51853 us␍␊
[17:38:54:563] [0001.438] Basic modules init took 935948 us␍␊
[17:38:54:568] [0001.442] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB␍␊
[17:38:54:573] [0001.448] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB␍␊
[17:38:54:581] [0001.453] Next stage binary read took 102859 us␍␊
[17:38:54:587] [0001.457] Carveout took -132465 us␍␊
[17:38:54:587] [0001.461] CPU initialization took 510787 us␍␊
[17:38:54:592] [0001.465] Total time taken by TegraBoot 1417129 us␍␊
[17:38:54:597] ␍␊
[17:38:54:597] [0001.469] Starting CPU & Halting co-processor ␍␊
[17:38:54:602] ␍␊
[17:38:54:602] 64NOTICE:  BL31: v1.3(release):b5eeb33␍␊
[17:38:54:609] NOTICE:  BL31: Built : 14:22:20, Apr 20 2022␍␊
[17:38:54:613] ERROR:   Error initializing runtime service trusty_fast␍␊
[17:38:54:721] [0001.591] RamCode = 0␍␊
[17:38:54:728] [0001.596] LPDDR4 Training: Read DT: Number of tables = 2␍␊
[17:38:54:728] [0001.601] EMC Training (SRC-freq: 204000; DST-freq: 1600000)␍␊
[17:38:54:743] [0001.614] EMC Training Successful␍␊
[17:38:54:746] [0001.617] 408000 not found in DVFS table␍␊
[17:38:54:757] [0001.623] RamCode = 0␍␊
[17:38:54:757] [0001.627] DT Write: emc-table@204000 succeeded␍␊
[17:38:54:762] [0001.632] DT Write: emc-table@1600000 succeeded␍␊
[17:38:54:767] [0001.636] LPDDR4 Training: Write DT: Number of tables = 2␍␊
[17:38:54:776] [0001.685] ␍␊
[17:38:54:776] [0001.686] Debug Init done␍␊
[17:38:54:781] [0001.688] Marked DTB cacheable␍␊
[17:38:54:785] [0001.691] Bootloader DTB loaded at 0x83000000␍␊
[17:38:54:785] [0001.696] Marked DTB cacheable␍␊
[17:38:54:790] [0001.699] Kernel DTB loaded at 0x83100000␍␊
[17:38:54:795] [0001.703] DeviceTree Init done␍␊
[17:38:54:806] [0001.716] Pinmux applied successfully␍␊
[17:38:54:810] [0001.720] gicd_base: 0x50041000␍␊
[17:38:54:815] [0001.724] gicc_base: 0x50042000␍␊
[17:38:54:820] [0001.727] Interrupts Init done␍␊
[17:38:54:820] [0001.731] Using base:0x60005090 & irq:208 for tick-timer␍␊
[17:38:54:826] [0001.736] Using base:0x60005098 for delay-timer␍␊
[17:38:54:831] [0001.740] platform_init_timer: DONE␍␊
[17:38:54:836] [0001.744] Timer(tick) Init done␍␊
[17:38:54:840] [0001.748] osc freq = 38400 khz␍␊
[17:38:54:845] [0001.752] ␍␊
[17:38:54:845] [0001.753] Welcome to L4T Cboot␍␊
[17:38:54:845] [0001.756] ␍␊
[17:38:54:845] [0001.757] Cboot Version: 00.00.2018.01-t210-a2f2e4b8␍␊
[17:38:54:850] [0001.762] calling constructors␍␊
[17:38:54:856] [0001.765] initializing heap␍␊
[17:38:54:861] [0001.767] initializing threads␍␊
[17:38:54:861] [0001.770] initializing timers␍␊
[17:38:54:866] [0001.773] creating bootstrap completion thread␍␊
[17:38:54:871] [0001.778] top of bootstrap2()␍␊
[17:38:54:871] [0001.780] CPU: ARM Cortex A57␍␊
[17:38:54:875] [0001.783] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000␍␊
[17:38:54:879] [0001.788] initializing platform␍␊
[17:38:54:888] [0001.795] Manufacturer: MF = 0xc2, ID MSB = 0x25␍␊
[17:38:54:890] [0001.800] ID LSB = 0x36, ID-CFI len = 194 bytes␍␊
[17:38:54:895] [0001.804] Macronix QSPI chip present␍␊
[17:38:54:899] [0001.808] SPI device register␍␊
[17:38:54:904] [0001.811] init boot device␍␊
[17:38:54:904] [0001.813] allocating memory for boot device(SPI)␍␊
[17:38:54:909] [0001.818] registering boot device␍␊
[17:38:54:927] [0001.836] QSPI bdev is already initialized␍␊
[17:38:54:930] [0001.840] Enable APE clock␍␊
[17:38:54:936] [0001.843] Un-powergate APE partition␍␊
[17:38:54:936] [0001.846] of_register: registering tegra_udc to of_hal␍␊
[17:38:54:943] [0001.851] of_register: registering inv20628-driver to of_hal␍␊
[17:38:54:948] [0001.857] of_register: registering ads1015-driver to of_hal␍␊
[17:38:54:953] [0001.863] of_register: registering lp8557-bl-driver to of_hal␍␊
[17:38:54:959] [0001.868] of_register: registering bq2419x_charger to of_hal␍␊
[17:38:54:965] [0001.874] of_register: registering bq27441_fuel_gauge to of_hal␍␊
[17:38:54:976] [0001.885] gpio framework initialized␍␊
[17:38:54:979] [0001.889] of_register: registering tca9539_gpio to of_hal␍␊
[17:38:54:985] [0001.894] of_register: registering tca9539_gpio to of_hal␍␊
[17:38:54:990] [0001.900] of_register: registering i2c_bus_driver to of_hal␍␊
[17:38:54:994] [0001.905] of_register: registering i2c_bus_driver to of_hal␍␊
[17:38:54:999] [0001.911] of_register: registering i2c_bus_driver to of_hal␍␊
[17:38:55:005] [0001.916] pmic framework initialized␍␊
[17:38:55:015] [0001.920] of_register: registering max77620_pmic to of_hal␍␊
[17:38:55:015] [0001.925] regulator framework initialized␍␊
[17:38:55:019] [0001.929] of_register: registering tps65132_bl_driver to of_hal␍␊
[17:38:55:025] [0001.935] initializing target␍␊
[17:38:55:035] [0001.941] gpio_driver_register: register 'tegra_gpio_driver' driver␍␊
[17:38:55:041] [0001.949] board ID = D78, board SKU = 0␍␊
[17:38:55:042] [0001.953] Skipping Z3!␍␊
[17:38:55:052] [0001.957] fixed regulator driver initialized␍␊
[17:38:55:066] [0001.975] initializing OF layer␍␊
[17:38:55:069] [0001.978] NCK carveout not present␍␊
[17:38:55:076] [0001.981] Skipping dts_overrides␍␊
[17:38:55:076] [0001.986] of_children_init: Ops found for compatible string nvidia,tegra210-i2c␍␊
[17:38:55:093] [0002.002] I2C Bus Init done␍␊
[17:38:55:093] [0002.005] of_children_init: Ops found for compatible string nvidia,tegra210-i2c␍␊
[17:38:55:107] [0002.015] I2C Bus Init done␍␊
[17:38:55:107] [0002.018] of_children_init: Ops found for compatible string nvidia,tegra210-i2c␍␊
[17:38:55:119] [0002.028] I2C Bus Init done␍␊
[17:38:55:119] [0002.031] of_children_init: Ops found for compatible string nvidia,tegra210-i2c␍␊
[17:38:55:132] [0002.041] I2C Bus Init done␍␊
[17:38:55:132] [0002.044] of_children_init: Ops found for compatible string nvidia,tegra210-i2c␍␊
[17:38:55:147] [0002.054] I2C Bus Init done␍␊
[17:38:55:147] [0002.057] of_children_init: Ops found for compatible string maxim,max77620␍␊
[17:38:55:159] [0002.067] max77620_init using irq 118␍␊
[17:38:55:162] [0002.072] register 'maxim,max77620' pmic␍␊
[17:38:55:166] [0002.076] gpio_driver_register: register 'max77620-gpio' driver␍␊
[17:38:55:172] [0002.082] of_children_init: Ops found for compatible string nvidia,tegra210-i2c␍␊
[17:38:55:184] [0002.093] I2C Bus Init done␍␊
[17:38:55:184] [0002.097] NCK carveout not present␍␊
[17:38:55:197] [0002.106] Find /i2c@7000c000's alias i2c0␍␊
[17:38:55:199] [0002.110] get eeprom at 1-a0, size 256, type 0␍␊
[17:38:55:209] [0002.119] Find /i2c@7000c500's alias i2c2␍␊
[17:38:55:212] [0002.122] get eeprom at 3-a0, size 256, type 0␍␊
[17:38:55:217] [0002.127] get eeprom at 3-ae, size 256, type 0␍␊
[17:38:55:222] [0002.131] pm_ids_update: Updating 1,a0, size 256, type 0␍␊
[17:38:55:227] [0002.137] I2C slave not started␍␊
[17:38:55:232] [0002.140] I2C write failed␍␊
[17:38:55:232] [0002.142] Writing offset failed␍␊
[17:38:55:237] [0002.145] eeprom_init: EEPROM read failed␍␊
[17:38:55:242] [0002.149] pm_ids_update: eeprom init failed␍␊
[17:38:55:247] [0002.153] pm_ids_update: Updating 3,a0, size 256, type 0␍␊
[17:38:55:274] [0002.183] pm_ids_update: The pm board id is 3448-0000-400␍␊
[17:38:55:278] [0002.190] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50␍␊
[17:38:55:288] [0002.199] pm_ids_update: pm id update successful␍␊
[17:38:55:294] [0002.203] pm_ids_update: Updating 3,ae, size 256, type 0␍␊
[17:38:55:324] [0002.233] pm_ids_update: The pm board id is 3449-0000-400␍␊
[17:38:55:328] [0002.239] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57␍␊
[17:38:55:337] [0002.247] pm_ids_update: pm id update successful␍␊
[17:38:55:368] [0002.278] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)␍␊
[17:38:55:374] [0002.283] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB␍␊
[17:38:55:381] [0002.291] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)␍␊
[17:38:55:387] [0002.297] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB␍␊
[17:38:55:397] [0002.306] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:fc:fe␍␊
[17:38:55:402] [0002.312] Plugin Manager: Parse ODM data 0x000a4000␍␊
[17:38:55:415] [0002.324] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 ␍␊
[17:38:55:429] [0002.339] Find /i2c@7000c000's alias i2c0␍␊
[17:38:55:432] [0002.343] get eeprom at 1-a0, size 256, type 0␍␊
[17:38:55:445] [0002.351] Find /i2c@7000c500's alias i2c2␍␊
[17:38:55:445] [0002.355] get eeprom at 3-a0, size 256, type 0␍␊
[17:38:55:450] [0002.360] get eeprom at 3-ae, size 256, type 0␍␊
[17:38:55:455] [0002.364] pm_ids_update: Updating 1,a0, size 256, type 0␍␊
[17:38:55:460] [0002.369] I2C slave not started␍␊
[17:38:55:465] [0002.372] I2C write failed␍␊
[17:38:55:470] [0002.375] Writing offset failed␍␊
[17:38:55:470] [0002.378] eeprom_init: EEPROM read failed␍␊
[17:38:55:475] [0002.382] pm_ids_update: eeprom init failed␍␊
[17:38:55:480] [0002.386] pm_ids_update: Updating 3,a0, size 256, type 0␍␊
[17:38:55:507] [0002.416] pm_ids_update: The pm board id is 3448-0000-400␍␊
[17:38:55:511] [0002.422] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50␍␊
[17:38:55:519] [0002.429] pm_ids_update: pm id update successful␍␊
[17:38:55:524] [0002.434] pm_ids_update: Updating 3,ae, size 256, type 0␍␊
[17:38:55:555] [0002.464] pm_ids_update: The pm board id is 3449-0000-400␍␊
[17:38:55:558] [0002.470] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57␍␊
[17:38:55:567] [0002.477] pm_ids_update: pm id update successful␍␊
[17:38:55:598] [0002.508] Add serial number:1422919052757 as DT property␍␊
[17:38:55:611] [0002.515] Applying platform configs␍␊
[17:38:55:617] [0002.522] platform-init is not present. Skipping␍␊
[17:38:55:617] [0002.526] calling apps_init()␍␊
[17:38:55:627] [0002.532] Couldn't find GPT header␍␊
[17:38:55:628] [0002.537] Proceeding to Cold Boot␍␊
[17:38:55:632] [0002.540] starting app android_boot_app␍␊
[17:38:55:632] [0002.544] Device state: unlocked␍␊
[17:38:55:638] [0002.547] display console init␍␊
[17:38:55:648] [0002.555] could not find regulator␍␊
[17:38:55:649] [0002.558] hdmi cable connected␍␊
[17:38:55:666] [0002.574] edid read success␍␊
[17:38:55:680] [0002.589] edid read success␍␊
[17:38:55:680] [0002.592] widthDT entry for leds-pwm not found␍␊
[17:38:55:690]  [0002.599] = 640, height = 480, frequency = 25174825␍␊
[17:38:55:696] [0002.604] width = 640, height = 480, frequency = 25174825␍␊
[17:38:55:701] [0002.610] width = 640, height = 480, frequency = 25174825␍␊
[17:38:55:706] [0002.615] width = 640, height = 480, frequency = 25174825␍␊
[17:38:55:711] [0002.620] width = 1920, height = 1080, frequency = 148500000␍␊
[17:38:55:717] [0002.626] width = 1280, height = 720, frequency = 74250000␍␊
[17:38:55:723] [0002.631] width = 640, height = 480, frequency = 25174825␍␊
[17:38:55:730] [0002.637] width = 720, height = 480, frequency = 26973026␍␊
[17:38:55:736] [0002.642] width = 720, height = 576, frequency = 26973026␍␊
[17:38:55:736] [0002.648] width = 1280, height = 720, frequency = 74175824␍␊
[17:38:55:742] [0002.653] width = 1280, height = 720, frequency = 74175824␍␊
[17:38:55:749] [0002.659] width = 1920, height = 1080, frequency = 148351648␍␊
[17:38:55:753] [0002.664] width = 1920, height = 1080, frequency = 148351648␍␊
[17:38:55:760] [0002.670] Best mode Width = 1920, Height = 1080, freq = 148351648␍␊
[17:38:55:773] [0002.678] tmds-config node not found␍␊
[17:38:55:773] [0002.682] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts␍␊
[17:38:55:788] [0002.696] setting 'vdd-1v8' regulator to 1800000 micro volts␍␊
[17:38:55:797] [0002.704] could not find regulator␍␊
[17:38:55:799] [0002.707] could not find regulator␍␊
[17:38:55:803] [0002.711] could not find regulator␍␊
[17:38:55:830] [0002.739] using default cmu settings␍␊
[17:38:55:832] [0002.742] dc_hdmi_enable, starting HDMI initialisation␍␊
[17:38:55:841] [0002.749] dc_hdmi_enable, HDMI initialisation complete␍␊
[17:38:55:849] [0002.754] list and configure display window␍␊
[17:38:55:854] [0002.762] display console init completed␍␊
[17:38:55:864] [0002.773] subnode volume_up is not found !␍␊
[17:38:55:867] [0002.777] subnode back is not found !␍␊
[17:38:55:873] [0002.781] subnode volume_down is not found !␍␊
[17:38:55:879] [0002.785] subnode menu is not found !␍␊
[17:38:55:879] [0002.789] Gpio keyboard init success␍␊
[17:38:55:960] [0002.869] found decompressor handler: lz4-legacy␍␊
[17:38:55:974] [0002.884] decompressing blob (type 1)...␍␊
[17:38:56:044] [0002.954] load_bmp_blob: panelresolution=1080 type=3␍␊
[17:38:56:047] [0002.959] -------> se_aes_verify_sbk_clear: 747␍␊
[17:38:56:055] [0002.963] se_aes_verify_sbk_clear: Error␍␊
[17:38:56:061] [0002.967] SE operation failed␍␊
[17:38:56:061] [0002.970] bl_battery_charging: connected to external power supply␍␊
[17:38:56:072] [0002.982] device_query_partition_size: failed to open partition spiflash0:MSC !␍␊
[17:38:56:078] [0002.989] MSC Partition not found␍␊
[17:38:56:089] [0002.995] device_query_partition_size: failed to open partition spiflash0:USP !␍␊
[17:38:56:092] [0003.003] USP partition read failed!␍␊
[17:38:56:097] [0003.006] blob_init: blob-partition USP header read failed␍␊
[17:38:56:102] [0003.012] android_boot Unable to update recovery partition␍␊
[17:38:56:107] [0003.017] kfs_getpartname: name = LNX␍␊
[17:38:56:112] [0003.021] Loading kernel from LNX␍␊
[17:38:56:122] [0003.030] Found 19 BFS partitions in "spiflash0"␍␊
[17:38:56:442] [0003.352] load kernel from storage␍␊
[17:38:56:451] [0003.357] decompressor handler not found␍␊
[17:38:56:714] [0003.623] Successfully loaded kernel and ramdisk images␍␊
[17:38:56:717] [0003.628] board ID = D78, board SKU = 0␍␊
[17:38:56:724] [0003.633] sdmmc node status = okay␍␊
[17:38:56:730] [0003.636] sdcard instance = 0␍␊
[17:38:56:730] [0003.639] sdmmc cd-inverted␍␊
[17:38:56:735] [0003.642] sdcard gpio handle 0x5b␍␊
[17:38:56:735] [0003.645] sdcard gpio pin 0xc9␍␊
[17:38:56:740] [0003.648] sdcard gpio flags 0x0␍␊
[17:38:56:745] [0003.651] vmmc-supply 0x9d␍␊
[17:38:56:745] [0003.653] cd_gpio_pin = 201␍␊
[17:38:56:749] [0003.656] pin_state = 0␍␊
[17:38:56:749] [0003.658] Found sdcard␍␊
[17:38:56:749] [0003.661] SD-card IS present ...␍␊
[17:38:56:754] [0003.664] load_and_boot_kernel: SD card detected OK␍␊
[17:38:56:759] [0003.670] load_bmp_blob: panelresolution=1080 type=3␍␊
[17:38:57:254] [0004.164] display bmp image done␍␊
[17:38:57:257] [0004.167] NCK carveout not present␍␊
[17:38:57:262] [0004.170] Skipping dts_overrides␍␊
[17:38:57:267] [0004.173] NCK carveout not present␍␊
[17:38:57:273] [0004.183] Find /i2c@7000c000's alias i2c0␍␊
[17:38:57:276] [0004.187] get eeprom at 1-a0, size 256, type 0␍␊
[17:38:57:286] [0004.195] Find /i2c@7000c500's alias i2c2␍␊
[17:38:57:289] [0004.199] get eeprom at 3-a0, size 256, type 0␍␊
[17:38:57:293] [0004.204] get eeprom at 3-ae, size 256, type 0␍␊
[17:38:57:298] [0004.208] pm_ids_update: Updating 1,a0, size 256, type 0␍␊
[17:38:57:304] [0004.213] I2C slave not started␍␊
[17:38:57:308] [0004.216] I2C write failed␍␊
[17:38:57:314] [0004.219] Writing offset failed␍␊
[17:38:57:314] [0004.222] eeprom_init: EEPROM read failed␍␊
[17:38:57:320] [0004.226] pm_ids_update: eeprom init failed␍␊
[17:38:57:325] [0004.230] pm_ids_update: Updating 3,a0, size 256, type 0␍␊
[17:38:57:351] [0004.260] pm_ids_update: The pm board id is 3448-0000-400␍␊
[17:38:57:355] [0004.267] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50␍␊
[17:38:57:365] [0004.275] pm_ids_update: pm id update successful␍␊
[17:38:57:369] [0004.280] pm_ids_update: Updating 3,ae, size 256, type 0␍␊
[17:38:57:401] [0004.310] pm_ids_update: The pm board id is 3449-0000-400␍␊
[17:38:57:404] [0004.316] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57␍␊
[17:38:57:414] [0004.324] pm_ids_update: pm id update successful␍␊
[17:38:57:445] [0004.355] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)␍␊
[17:38:57:451] [0004.360] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB␍␊
[17:38:57:457] [0004.368] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)␍␊
[17:38:57:464] [0004.374] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB␍␊
[17:38:57:475] [0004.382] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:fc:fe␍␊
[17:38:57:479] [0004.389] Plugin Manager: Parse ODM data 0x000a4000␍␊
[17:38:57:492] [0004.401] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 ␍␊
[17:38:57:498] [0004.409] Add serial number:1422919052757 as DT property␍␊
[17:38:57:510] [0004.418] "bpmp" doesn't exist, creating ␍␊
[17:38:57:513] [0004.424] Updated bpmp info to DTB␍␊
[17:38:57:518] [0004.429] Updated initrd info to DTB␍␊
[17:38:57:524] [0004.432] "proc-board" doesn't exist, creating ␍␊
[17:38:57:529] [0004.438] Updated board info to DTB␍␊
[17:38:57:534] [0004.442] "pmu-board" doesn't exist, creating ␍␊
[17:38:57:540] [0004.448] Updated board info to DTB␍␊
[17:38:57:545] [0004.451] "display-board" doesn't exist, creating ␍␊
[17:38:57:550] [0004.457] Updated board info to DTB␍␊
[17:38:57:555] [0004.460] "reset" doesn't exist, creating ␍␊
[17:38:57:555] [0004.465] Updated reset info to DTB␍␊
[17:38:57:560] [0004.468] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 ␍␊
[17:38:57:597] [0004.508] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 ␍␊
[17:38:57:603] [0004.513] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 nv-auto-config ␍␊
[17:38:57:617] [0004.527] Updated bootarg info to DTB␍␊
[17:38:57:622] [0004.531] Adding uuid 00000001644495851000000015030380 to DT␍␊
[17:38:57:629] [0004.537] Adding eks info 0 to DT␍␊
[17:38:57:634] [0004.542] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7␍␊
[17:38:57:641] [0004.548] Updated memory info to DTB␍␊
[17:38:57:652] [0004.556] set vdd_core voltage to 1075 mv␍␊
[17:38:57:652] [0004.560] setting 'vdd-core' regulator to 1075000 micro volts␍␊
[17:38:57:657] [0004.566] Found secure-pmc; disable BPMP␍␊
[17:38:58:048] ␍␊
[17:38:58:048] ␍␊
[17:38:58:048] U-Boot 2020.04-g4335beb (Apr 20 2022 - 14:22:25 -0700)␍␊
[17:38:58:059] ␍␊
[17:38:58:059] SoC: tegra210␍␊
[17:38:58:059] Model: NVIDIA Jetson Nano Developer Kit␍␊
[17:38:58:059] Board: NVIDIA P3450-0000␍␊
[17:38:58:069] DRAM:  4 GiB␍␊
[17:38:58:373] MMC:   sdhci@700b0000: 1, sdhci@700b0600: 0␍␊
[17:38:58:376] Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB␍␊
[17:38:58:406] *** Warning - bad CRC, using default environment␍␊
[17:38:58:409] ␍␊
[17:38:58:409] In:    serial␍␊
[17:38:58:415] Out:   serial␍␊
[17:38:58:415] Err:   serial␍␊
[17:38:58:420] Net:   No ethernet found.␍␊
[17:38:58:420] Hit any key to stop autoboot:  2 <0x08><0x08><0x08> 1 <0x08><0x08><0x08> 0 ␍␊
[17:39:00:628] switch to partitions #0, OK␍␊
[17:39:00:628] mmc1 is current device␍␊
[17:39:00:923] Scanning mmc 1:1...␍␊
[17:39:01:050] Found /boot/extlinux/extlinux.conf␍␊
[17:39:01:053] Retrieving file: /boot/extlinux/extlinux.conf␍␊
[17:39:01:133] 1188 bytes read in 40 ms (28.3 KiB/s)␍␊
[17:39:01:136] L4T boot options␍␊
[17:39:01:136] 1:⇥	primary kernel␍␊
[17:39:01:144] 2:⇥	Custom Header Config: <CSI Camera Arducam Dual>␍␊
[17:39:01:149] Enter choice: 2:⇥	Custom Header Config: <CSI Camera Arducam Dual>␍␊
[17:39:04:146] Retrieving file: /boot/initrd␍␊
[17:39:04:524] 7160179 bytes read in 338 ms (20.2 MiB/s)␍␊
[17:39:04:527] Retrieving file: /boot/arducam/Image␍␊
[17:39:06:127] 34551816 bytes read in 1560 ms (21.1 MiB/s)␍␊
[17:39:06:129] append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1  earlycon=uart8250,mmio32,0x70006000  root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 nv-auto-config quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0␍␊
[17:39:06:191] Retrieving file: /boot/arducam/dts/tegra210-p3448-0000-p3449-0000-b00-user-custom.dtb␍␊
[17:39:06:311] 241705 bytes read in 76 ms (3 MiB/s)␍␊
[17:39:06:384] ## Flattened Device Tree blob at 83000000␍␊
[17:39:06:387]    Booting using the fdt blob at 0x83000000␍␊
[17:39:06:396] ERROR: reserving fdt memory region failed (addr=0 size=0)␍␊
[17:39:06:396] ERROR: reserving fdt memory region failed (addr=0 size=0)␍␊
[17:39:06:402]    Using Device Tree in place at 0000000083000000, end 000000008303e028␍␊
[17:39:06:412] copying carveout for /host1x@50000000/dc@54200000...␍␊
[17:39:06:414] copying carveout for /host1x@50000000/dc@54240000...␍␊
[17:39:06:464] DT property /chosen/nvidia,bluetooth-mac missing in source; can't copy␍␊
[17:39:06:471] DT property /chosen/nvidia,wifi-mac missing in source; can't copy␍␊
[17:39:06:484] DT property /psci/nvidia,system-lp0-disable missing in source; can't copy␍␊
[17:39:06:489] ␍␊
[17:39:06:489] Starting kernel ...␍␊
[17:39:06:494] ␍␊
[17:39:06:603] [    0.000000] Booting Linux on physical CPU 0x0␍␊
[17:39:06:606] [    0.000000] Linux version 4.9.253-tegra (jenkins@feaf98b9a84d) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Tue May 17 09:07:08 UTC 2022␍␊
[17:39:06:628] [    0.000000] Boot CPU: AArch64 Processor [411fd071]␍␊
[17:39:06:635] [    0.000000] OF: fdt:memory scan node memory@80000000, reg size 32,␍␊
[17:39:06:642] [    0.000000] OF: fdt: - 80000000 ,  7ee00000␍␊
[17:39:06:649] [    0.000000] OF: fdt: - 100000000 ,  7f200000␍␊
[17:39:06:649] [    0.000000] Found tegra_fbmem: 00800000@92ca9000␍␊
[17:39:06:656] [    0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '')␍␊
[17:39:06:661] [    0.000000] bootconsole [uart8250] enabled␍␊
[17:39:08:219] [    1.162775] tegradc tegradc.1: dpd enable lookup fail:-19␍␊
[17:39:08:537] [    1.416187] arducam-csi2: arducam_read: Reading register 0x103 failed␍␊
[17:39:08:543] [    1.416194] arducam-csi2 8-000c: probe failed␍␊
[17:39:08:550] [    1.416231] arducam-csi2 8-000c: Failed to setup board.␍␊
[17:39:09:561] [    2.505297] cgroup: cgroup2: unknown option "nsdelegate"␍␊
[17:39:11:271] [    4.214897] random: crng init done␍␊
[17:39:11:274] [    4.218329] random: 7 urandom warning(s) missed due to ratelimiting␍␊
[17:39:13:376] [    6.319521] using random self ethernet address␍␊
[17:39:13:378] [    6.324126] using random host ethernet address␍␊
[17:39:16:049] [    8.993380] using random self ethernet address␍␊
[17:39:16:052] [    8.997887] using random host ethernet address␍␊
[17:39:26:457] ␍␍␊
[17:39:26:468] Ubuntu 18.04.6 LTS ubuntu ttyS0␍␊
[17:39:26:471] ␍␊
[17:39:26:480] ubuntu login: [   20.415351] Bridge firewalling registered␍␊