[0003.402] Enabled early print
[0003.404] [L4T TegraBoot] (version 00.00.2018.01-l4t-1463e5a5)
[0003.410] Processing in recovery mode
[0003.413] A02 Bootrom Patch rev = 1023
[0003.417] Power-up reason: pmc por
[0003.420] Established communication link with host
[0004.614] Odmdata from BCT: 0x00094000
[0004.618] DebugPort= 0x3
[0004.620] BoardId read from EEPROM/NCT: 3448
[0004.624] BoardID = 3448, SKU = 0x2
[0004.652] NvTbootInit_Porg: Setting GPIO_A6 for HDMI ...
[0004.657] max77620 setting MBLPD bit
[0004.660] No Battery Present
[0004.663] RamCode = 0
[0004.665] Platform has DDR4 type RAM
[0004.669] max77620 disabling SD1 Remote Sense
[0004.673] Setting DDR voltage to 1125mv
[0004.677] Serial Number of Pmic Max77663: 0xd15ee
[0004.684] Entering ramdump check
[0004.687] Get RamDumpCarveOut = 0x0
[0004.691] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0004.696] Last reboot was clean, booting normally!
[0004.700] Sdram initialization is successful
[0004.704] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0004.711] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0004.716] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0004.722] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0004.728] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0004.734] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0004.740] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0004.746] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0004.762] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0004.768] Platform-DebugCarveout: 0
[0004.771] Downloaded BCT successfully
[0004.897] Downloaded Bootloader successfully
[0004.947] Downloaded rp1 successfully
[0004.978] MAX77620_GPIO5 configured
[0004.982] CPU power rail is up
[0004.985] CPU clock enabled
[0004.988] Performing RAM repair
[0004.991] Updating A64 Warmreset Address to 0x92c002e9
[0004.997] Enable APE clock/reset
[0005.000] Error in NvTbootGetTOSBinaryLength: 0x11 !
[0005.005] Loading Secure OS image failed.
[0005.009] Set NvDecSticky Bits
[0005.013] GSC2 address ff53fffc value c0edbbcc
[0005.019] GSC MC Settings done
[0005.023] Next binary entry address: 0x92c00258
[0005.028] BoardId: 3448
[0005.030] Starting CPU & Halting co-processor

[0005.162]
[0005.163] Debug Init done
[0005.167] Marked DTB cacheable
[0005.170] Bootloader DTB loaded at 0x83000400
[0005.174] DeviceTree Init done
[0005.187] Pinmux applied successfully
[0005.191] gicd_base: 0x50041000
[0005.195] gicc_base: 0x50042000
[0005.198] Interrupts Init done
[0005.202] Using base:0x60005090 & irq:208 for tick-timer
[0005.207] Using base:0x60005098 for delay-timer
[0005.211] platform_init_timer: DONE
[0005.215] Timer(tick) Init done
[0005.219] osc freq = 38400 khz
[0005.223]
[0005.224] Welcome to L4T Cboot
[0005.227]
[0005.228] Cboot Version: 00.00.2018.01-t210-40c3ff9c
[0005.233] calling constructors
[0005.236] initializing heap
[0005.239] initializing threads
[0005.242] initializing timers
[0005.244] creating bootstrap completion thread
[0005.249] top of bootstrap2()
[0005.252] CPU: ARM Cortex A57
[0005.255] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0005.259] initializing platform
[0005.361] Config for emmc ddr50 mode completed
[0005.366] sdmmc bdev is already initialized
[0005.370] of_register: registering tegra_udc to of_hal
[0005.375] of_register: registering inv20628-driver to of_hal
[0005.381] of_register: registering ads1015-driver to of_hal
[0005.386] of_register: registering lp8557-bl-driver to of_hal
[0005.392] of_register: registering bq2419x_charger to of_hal
[0005.397] of_register: registering bq27441_fuel_gauge to of_hal
[0005.409] gpio framework initialized
[0005.412] of_register: registering tca9539_gpio to of_hal
[0005.418] of_register: registering tca9539_gpio to of_hal
[0005.423] of_register: registering i2c_bus_driver to of_hal
[0005.429] of_register: registering i2c_bus_driver to of_hal
[0005.434] of_register: registering i2c_bus_driver to of_hal
[0005.440] pmic framework initialized
[0005.443] of_register: registering max77620_pmic to of_hal
[0005.449] regulator framework initialized
[0005.453] of_register: registering tps65132_bl_driver to of_hal
[0005.459] initializing target
[0005.465] gpio_driver_register: register 'tegra_gpio_driver' driver
[0005.473] board ID = D78, board SKU = 2
[0005.479] fixed regulator driver initialized
[0005.496] initializing OF layer
[0005.500] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0005.517] I2C Bus Init done
[0005.520] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0005.530] I2C Bus Init done
[0005.533] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0005.543] I2C Bus Init done
[0005.546] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0005.556] I2C Bus Init done
[0005.559] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0005.569] I2C Bus Init done
[0005.572] of_children_init: Ops found for compatible string maxim,max77620
[0005.582] max77620_init using irq 118
[0005.587] register 'maxim,max77620' pmic
[0005.591] gpio_driver_register: register 'max77620-gpio' driver
[0005.598] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0005.608] I2C Bus Init done
[0005.612] Applying platform configs
[0005.619] platform-init is not present. Skipping
[0005.623] calling apps_init()
[0005.640] Found 17 GPT partitions in "sdmmc3_user"
[0005.644] Proceeding to flashing Server
[0005.648] usbdcd_reinit Initialize driver to use already enumerated device
[0005.655] nv3p_priv_usbf_open USB configuration success
[0005.663] Writing LNX partition
[0005.716] partition LNX write successful.
[0005.731] Writing BCT partition
[0006.123] partition BCT write successful.
[0006.136] Change state to cold boot mode
[0006.139] Flushing data to stroage