öÿâ [0013.185] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0013.193] I> MB1 (prd-version: 1.5.1.7-t194-41334769-98030a79) [0013.199] I> Boot-mode: Platform RCM [0013.202] I> Chip revision : A02P [0013.205] I> Bootrom patch version : 15 (correctly patched) [0013.210] I> ATE fuse revision : 0x200 [0013.214] I> Ram repair fuse : 0x0 [0013.217] I> Ram Code : 0x2 [0013.220] I> rst_source : 0x0 [0013.222] I> rst_level : 0x0 [0013.226] I> USB configuration success [0015.310] I> mb2 image downloaded [0015.333] I> Recovery boot mode 0 [0015.337] I> Boot-device: eMMC [0015.342] I> UPHY full init done [0015.346] I> MB1 done [0015.351] W> Profiler not initialized [0015.354] I> Welcome to MB2(TBoot-BPMP) Applet (version: 00.00.2018.32-mobile-78b59fcb) [0015.362] W> Profiler not initialized [0015.366] I> DMA Heap @ [0x40020000 - 0x40065800] [0015.370] I> Default Heap @ [0xd486400 - 0xd48a400] [0015.375] W> Profiler not initialized [0015.379] W> Profiler not initialized [0015.382] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0015.387] W> device prod register failed [0015.391] W> Profiler not initialized [0015.448] I> sdmmc DDR50 mode [0015.452] I> No supported QSPI flash found [0015.456] E> QSPI Flash: Insufficient flash size (0 MB) [0015.461] I> QSPI Flash is not present. [0015.512] E> Link startup dme_set failed [0015.516] E> UFS initialization failed [0015.519] I> UFS is not present [0015.522] W> Profiler not initialized [0015.530] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0015.539] I> Found 42 partitions in SDMMC_USER (instance 3) [0015.545] W> Profiler not initialized [0015.548] W> Profiler not initialized [0015.552] W> Profiler not initialized [0015.555] I> Entering 3p server [0015.559] I> USB configuration success [0016.472] I> Populate chip info [0016.501] I> Populate eeprom info [0016.505] I> Populate eeprom info for module cvm [0016.601] I> Rebooting : reboot-recovery [001ÿâ [0008.093] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0008.102] I> MB1 (prd-version: 1.5.1.7-t194-41334769-98030a79) [0008.107] I> Boot-mode: RCM [0008.110] I> Chip revision : A02P [0008.113] I> Bootrom patch version : 15 (correctly patched) [0008.118] I> ATE fuse revision : 0x200 [0008.121] I> Ram repair fuse : 0x0 [0008.124] I> Ram Code : 0x2 [0008.127] I> rst_source : 0xb [0008.130] I> rst_level : 0x1 [0008.133] I> USB configuration success [0012.980] I> bct_bootrom image downloaded [0012.989] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0012.996] I> Temperature = 37500 [0012.999] W> Skipping boost for clk: BPMP_CPU_NIC [0013.004] W> Skipping boost for clk: BPMP_APB [0013.008] W> Skipping boost for clk: AXI_CBB [0013.012] W> Skipping boost for clk: AON_CPU_NIC [0013.016] W> Skipping boost for clk: CAN1 [0013.020] W> Skipping boost for clk: CAN2 [0013.024] I> Boot-device: eMMC [0013.027] I> Boot-device: eMMC [0013.030] I> bct_mb1 image downloaded [0013.039] I> ECC region[0]: Start:0x0, End:0x0 [0013.044] I> ECC region[1]: Start:0x0, End:0x0 [0013.048] I> ECC region[2]: Start:0x0, End:0x0 [0013.052] I> ECC region[3]: Start:0x0, End:0x0 [0013.056] I> ECC region[4]: Start:0x0, End:0x0 [0013.060] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0013.066] I> Non-ECC region[1]: Start:0x0, End:0x0 [0013.070] I> Non-ECC region[2]: Start:0x0, End:0x0 [0013.075] I> Non-ECC region[3]: Start:0x0, End:0x0 [0013.079] I> Non-ECC region[4]: Start:0x0, End:0x0 [0013.085] E> FAILED: Thermal config [0013.093] E> FAILED: MEMIO rail config [0013.111] I> bct_mem image downloaded [0014.394] I> blob image downloaded [0014.422] I> Recovery boot mode 0 [0014.492] I> MB1 done ÿýÿàmain enter SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init ÿâ [0014.500] I> Welcome to MB2(TBoot-BPMP) Recovery (version: 00.00.2018.32-mobile-21d977c9) [0014.501] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0014.502] I> Default Heap @ [0xd486400 - 0xd48a400] [0014.503] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0014.509] W> device prod register failed [0014.513] I> parsing oem signed section of bpmp-fw header done [0014.521] I> bpmp-fw binary copied from blob [0014.523] I> oem authentication of bpmp-fw header done [0014.528] I> bpmp-fw: Authentication init Done [0014.532] I> parsing oem signed section of cpubl header done [0014.538] I> cpubl binary copied from blob [0014.541] I> bpmp-fw: Authentication Finalize Done [0014.546] I> oem authentication of cpubl header done [0014.551] I> cpubl: Authentication init Done [0014.555] I> parsing oem signed section of tos header done [0014.561] I> tos binary copied from blob [0014.564] I> Relocating BR-BCT [0014.567] I> cpubl: Authentication Finalize Done [0014.572] I> oem authentication of tos header done [0014.576] I> tos: Authentication init Done [0014.580] I> parsing oem signed section of bpmp-fw-dtb header done [0014.589] I> bpmp-fw-dtb binary copied from blob [0014.590] I> tos: Authentication Finalize Done [0014.596] I> oem authentication of bpmp-fw-dtb header done [0014.600] I> bpmp-fw-dtb: Authentication init Done [0014.605] I> parsing oem signed section of cpubl-dtb header done [0014.611] I> cpubl-dtb binary copied from blob [0014.615] I> bpmp-fw-dtb: Authentication Finalize Done [0014.854] I> oem authentication of cpubl-dtb header done [0014.855] I> cpubl-dtb: Authentication init Done [0014.856] I> parsing oem signed section of eks header done [0014.856] I> eks binary copied from blob [0014.857] I> cpubl-dtb: Authentication Finalize Done [0014.857] I> oem authentication of eks header done [0014.858] I> eks: Authentication init Done [0014.862] I> eks: Authentication Finalize Done [0014.866] I> EKB detected (length: 0x410) @ VA:0x526fb600 ÿäNOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:15:32, Jul 26 2021 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 41: hwkey-agent is running!! hwkey-agent: 315: key_mgnt_processing ....... hwkey-agent: 223: Setting EKB key 0 to slot 14 hwkey-agent: 178: Init hweky-agent services!! luks-srv: 40: luks-srv is running!! luks-srv: 157: Init luks-srv IPC services!! platform_bootstrap_epilog: trusty bootstrap complete ÿâ welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is e73a758761f0c6d24a1e69a2ac6b5035 tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized 392 clocks registered clk_mrq_init: mrq handler registered clk initialized nvlink initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized /uphy is not enabled status = disabled uphy_dt initialized uphy initialized safereg_init: period 80 ms ec_late initialized mrq initialized ÿá [0015.363] I> Welcome to TBoot-CPU Recovery ÿâfmon_post initialized ÿá[0015.363] I> Heap: [0xa4000000 ... 0xaa000000 [0015.368] I> gpio framework initialized [0015.372] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver ÿâclk_set_parent failed for clk i2c2, parent pll_aon (-22) clk_set_parent failed for clk i2c8, parent pll_aon (-22) clk_dt_late initialized machine_check initialized pm_post initialized dbells initialized avfs_clk_platform_post initialized dmce initialized cvc initialized ccplex_avfs_hw_init: nafll_cluster0: not monitored ccplex_avfs_hw_init: nafll_cluster1: not monitored ccplex_avfs_hw_init: nafll_cluster2: not monitored ccplex_avfs_hw_init: nafll_cluster3: not monitored avfs_clk_mach_post initialized regulator_post initialized rm initialized sc7_diag initialized thermal_test initialized serial_late initialized clk_post initialized clk_dt_post initialized mc_reg initialized pg_post initialized dyn_modules initialized sku_debugfs initialized speedo_debugfs initialized adc_debugfs initialized clk_debugfs initialized ÿá[0015.379] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver [0015.462] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 [0015.468] E> Error -1 when finding node with path /i2c@c240000 [0015.473] E> fetch_driver_phandle_from_dt: failed to get i2c node for tca9539 [0015.481] E> Error -1 when finding node with path /i2c@c240000 [0015.486] E> fetch_driver_phandle_from_dt: failed to get i2c node for tca9539 [0015.493] W> tegrabl_tca9539_init: failed to fetch phandle from dt ÿâemc_debugfs initialized dvs_debugfs initialized ÿá[0015.499] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 ÿâfmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized debugfs_cons initialized mail_fs initialized profile initialized cvc_debugfs initialized dmce_debugfs initialized ec_debugfs initialized rm_debugfs initialized soctherm_debug initialized gr_reader initialized mods initialized dt_fs initialized debugfs_mrq initialized debug_mrq initialized debug_safereg initialized initializing target calling apps_init() starting app shell entering main console loop ] ÿá[0015.510] E> Error -1 when finding node with path /i2c@c240000 [0015.561] E> fetch_driver_phandle_from_dt: failed to get i2c node for tca9539 [0015.568] E> Error -1 when finding node with path /i2c@c240000 [0015.574] E> fetch_driver_phandle_from_dt: failed to get i2c node for tca9539 [0015.581] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0015.588] I> fixed regulator driver initialized [0015.608] I> CPU: Nvidia Carmel [0015.609] I> CPU: MIDR: 0x4e0f0040, MPIDR: 0x80000000 [0015.609] I> chip revision : A02P [0015.609] I> Boot-device: eMMC [0015.609] I> Boot_device: SDMMC_BOOT instance: 3 [0016.052] I> sdmmc-3 params source = boot args [0016.053] I> sdmmc bdev is already initialized [0016.053] I> sdmmc-3 params source = boot args [0016.080] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0016.092] I> Found 42 partitions in SDMMC_USER (instance 3) [0016.093] I> Recovery boot_type: 0 [0016.093] I> Entering 3p server [0016.093] I> USB configuration success [0016.156] I> Writing kernel-dtb partition. [0016.265] I> Rebooting : reset-coldboot ÿäÿâShutdown state requested 1 Rebooting system ... ÿâ [0000.055] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0000.063] I> MB1 (prd-version: 1.5.1.7-t194-41334769-98030a79) [0000.069] I> Boot-mode: Coldboot [0000.071] I> Chip revision : A02P [0000.075] I> Bootrom patch version : 15 (correctly patched) [0000.080] I> ATE fuse revision : 0x200 [0000.083] I> Ram repair fuse : 0x0 [0000.086] I> Ram Code : 0x2 [0000.089] I> rst_source : 0xb [0000.091] I> rst_level : 0x1 [0000.095] I> Boot-device: eMMC [0000.110] I> sdmmc DDR50 mode [0000.114] W> No valid slot number is found in scratch register [0000.120] W> Return default slot: _a [0000.123] I> Active Boot chain : 0 [0000.126] I> Boot-device: eMMC [0000.130] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.136] I> Temperature = 40500 [0000.139] W> Skipping boost for clk: BPMP_CPU_NIC [0000.143] W> Skipping boost for clk: BPMP_APB [0000.147] W> Skipping boost for clk: AXI_CBB [0000.151] W> Skipping boost for clk: AON_CPU_NIC [0000.156] W> Skipping boost for clk: CAN1 [0000.159] W> Skipping boost for clk: CAN2 [0000.164] I> Boot-device: eMMC [0000.166] I> Boot-device: eMMC [0000.176] I> Sdmmc: HS400 mode enabled [0000.180] I> ECC region[0]: Start:0x0, End:0x0 [0000.184] I> ECC region[1]: Start:0x0, End:0x0 [0000.189] I> ECC region[2]: Start:0x0, End:0x0 [0000.193] I> ECC region[3]: Start:0x0, End:0x0 [0000.197] I> ECC region[4]: Start:0x0, End:0x0 [0000.201] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.207] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.211] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.216] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.220] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.225] E> FAILED: Thermal config [0000.233] E> FAILED: MEMIO rail config [0000.251] I> Boot-device: eMMC [0000.261] I> sdmmc bdev is already initialized [0000.333] I> MB1 done ÿýÿàmain enter SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init ÿâ [0000.341] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-938a8cd8) [0000.342] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0000.343] I> Default Heap @ [0xd486400 - 0xd48a400] [0000.343] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0000.349] W> device prod register failed [0000.353] I> Boot-device: eMMC [0000.356] I> Boot_device: SDMMC_BOOT instance: 3 [0000.362] I> sdmmc-3 params source = boot args [0000.365] I> sdmmc bdev is already initialized [0000.369] I> sdmmc-3 params source = boot args [0000.377] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0000.384] I> Found 42 partitions in SDMMC_USER (instance 3) [0000.385] W> No valid slot number is found in scratch register [0000.390] W> Return default slot: _a [0000.393] I> Active Boot chain : 0 [0000.397] I> parsing oem signed section of bpmp-fw header done [0000.402] I> bpmp-fw binary init read from storage [0000.407] I> oem authentication of bpmp-fw header done [0000.414] I> bpmp-fw binary done read from storage [0000.416] I> bpmp-fw: Authentication init Done [0000.421] I> parsing oem signed section of cpubl header done [0000.426] I> cpubl binary init read from storage [0000.431] I> bpmp-fw: Authentication Finalize Done [0000.436] I> oem authentication of cpubl header done [0000.440] I> cpubl binary done read from storage [0000.445] I> cpubl: Authentication init Done [0000.450] I> parsing oem signed section of rce header done [0000.454] I> rce binary init read from storage [0000.459] I> Relocating BR-BCT [0000.461] I> cpubl: Authentication Finalize Done [0000.466] I> oem authentication of rce header done [0000.470] I> rce binary done read from storage [0000.475] I> rce: Authentication init Done [0000.479] I> parsing oem signed section of ape header done [0000.484] I> ape binary init read from storage [0000.488] I> rce: Authentication Finalize Done [0000.493] I> oem authentication of ape header done [0000.497] I> ape binary done read from storage [0000.501] I> ape: Authentication init Done [0000.506] I> parsing oem signed section of tos header done [0000.511] I> tos binary init read from storage [0000.515] I> ape: Authentication Finalize Done [0000.520] I> oem authentication of tos header done [0000.524] I> tos binary done read from storage [0000.528] I> tos: Authentication init Done [0000.532] I> parsing oem signed section of bpmp-fw-dtb header done [0000.538] I> bpmp-fw-dtb binary init read from storage [0000.543] I> tos: Authentication Finalize Done [0000.549] I> oem authentication of bpmp-fw-dtb header done [0000.556] I> bpmp-fw-dtb binary done read from storage [0000.558] I> bpmp-fw-dtb: Authentication init Done [0000.563] I> parsing oem signed section of cpubl-dtb header done [0000.568] I> cpubl-dtb binary init read from storage [0000.573] I> bpmp-fw-dtb: Authentication Finalize Done [0000.611] I> oem authentication of cpubl-dtb header done [0000.612] I> cpubl-dtb binary done read from storage [0000.612] I> cpubl-dtb: Authentication init Done [0000.614] I> parsing oem signed section of eks header done [0000.615] I> eks binary init read from storage [0000.615] I> cpubl-dtb: Authentication Finalize Done [0000.616] I> oem authentication of eks header done [0000.620] I> eks binary done read from storage [0000.624] I> eks: Authentication init Done [0000.628] I> eks: Authentication Finalize Done [0000.632] I> EKB detected (length: 0x410) @ VA:0x52700400 ÿäNOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:15:32, Jul 26 2021 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 41: hwkey-agent is running!! hwkey-agent: 315: key_mgnt_processing ....... hwkey-agent: 223: Setting EKB key 0 to slot 14 hwkey-agent: 178: Init hweky-agent services!! luks-srv: 40: luks-srv is running!! luks-srv: 157: Init luks-srv IPC services!! platform_bootstrap_epilog: trusty bootstrap complete ÿâ welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is e73a758761f0c6d24a1e69a2ac6b5035 tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized 392 clocks registered WARNING: pll_c4 has no dyn ramp clk_mrq_init: mrq handler registered clk initialized nvlink initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized uphy_mrq_init: mrq handler registered uphy_dt initialized uphy initialized safereg_init: period 80 ms ec_late initialized ÿá ÿâmrq initialized ÿá[0001.136] I> Welcome to Cboot ÿâfmon_post initialized ÿá[0001.136] I> Cboot Version: t194-cfa2bc91 [0001.137] I> CPU-BL Params @ 0xf2820000 [0001.137] I> 0) Base:0x00000000 Size:0x00000000 [0001.141] I> 1) Base:0xf1100000 Size:0x00100000 [0001.145] I> 2) Base:0xf2000000 Size:0x00200000 [0001.150] I> 3) Base:0xf1200000 Size:0x00200000 [0001.154] I> 4) Base:0xf1000000 Size:0x00100000 [0001.159] I> 5) Base:0xf0f00000 Size:0x00100000 ÿâclk_set_parent failed for clk i2c2, parent pll_aon (-22) clk_set_parent failed for clk i2c8, parent pll_aon (-22) clk_dt_late initialized machine_check initialized pm_post initialized dbells initialized avfs_clk_platform_post initialized dmce initialized cvc initialized ccplex_avfs_hw_init: nafll_cluster0: not monitored ccplex_avfs_hw_init: nafll_cluster1: not monitored ccplex_avfs_hw_init: nafll_cluster2: not monitored ccplex_avfs_hw_init: nafll_cluster3: not monitored avfs_clk_mach_post initialized regulator_post initialized rm initialized sc7_diag initialized thermal_test initialized serial_late initialized clk_post initialized clk_dt_post initialized mc_reg initialized pg_post initialized dyn_modules initialized sku_debugfs initialized speedo_debugfs initialized adc_debugfs initialized clk_debugfs initialized ÿá[0001.163] I> 6) Base:0xf3800000 Size:0x00400000 [0001.243] I> 7) Base:0xf1c00000 Size:0x00400000 [0001.247] I> 8) Base:0xf0e00000 Size:0x00100000 [0001.252] I> 9) Base:0xf0d00000 Size:0x00100000 [0001.256] I> 10) Base:0xf3000000 Size:0x00800000 [0001.260] I> 11) Base:0x40000000 Size:0x00040000 [0001.265] I> 12) Base:0xf0c00000 Size:0x00100000 [0001.269] I> 13) Base:0x40046000 Size:0x00002000 [0001.274] I> 14) Base:0x40048000 Size:0x00002000 ÿâemc_debugfs initialized dvs_debugfs initialized ÿá[0001.278] I> 15) Base:0xac000000 Size:0x00004000 [0001.288] I> 16) Base:0x4004a000 Size:0x00002000 ÿâfmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized debugfs_cons initialized mail_fs initialized profile initialized cvc_debugfs initialized dmce_debugfs initialized ec_debugfs initialized rm_debugfs initialized soctherm_debug initialized gr_reader initialized mods initialized dt_fs initialized debugfs_mrq initialized debug_mrq initialized debug_safereg initialized initializing target calling apps_init() starting app shell entering main console loop ] ÿá[0001.292] I> 17) Base:0xf0b00000 Size:0x00100000 [0001.342] I> 18) Base:0x4004c000 Size:0x00002000 [0001.347] I> 19) Base:0xf2200000 Size:0x00600000 [0001.351] I> 20) Base:0x4004e000 Size:0x00002000 [0001.356] I> 21) Base:0xf0ad0000 Size:0x0000c000 [0001.360] I> 22) Base:0x00000000 Size:0x00000000 [0001.365] I> 23) Base:0xf0ae0000 Size:0x00020000 [0001.369] I> 24) Base:0xf6000000 Size:0x02000000 [0001.374] I> 25) Base:0x40050000 Size:0x00002000 [0001.378] I> 26) Base:0x40040000 Size:0x00006000 [0001.383] I> 27) Base:0xf1800000 Size:0x00400000 [0001.387] I> 28) Base:0xf4c00000 Size:0x01400000 [0001.392] I> 29) Base:0xf1400000 Size:0x00400000 [0001.396] I> 30) Base:0x00000000 Size:0x00000000 [0001.400] I> 31) Base:0x00000000 Size:0x00000000 [0001.405] I> 32) Base:0xf8000000 Size:0x08000000 [0001.409] I> 33) Base:0x00000000 Size:0x00000000 [0001.414] I> 34) Base:0xf3c00000 Size:0x01000000 [0001.418] I> 35) Base:0xab000000 Size:0x01000000 [0001.423] I> 36) Base:0xa0000000 Size:0x0b000000 [0001.427] I> 37) Base:0xf2800000 Size:0x00800000 [0001.432] I> 38) Base:0x80000000 Size:0x20000000 [0001.436] I> 39) Base:0xb0000000 Size:0x08000000 [0001.441] I> 40) Base:0x00000000 Size:0x00000000 [0001.445] I> 41) Base:0x00000000 Size:0x00000000 [0001.450] I> 42) Base:0x00000000 Size:0x00000000 [0001.454] I> 43) Base:0x00000000 Size:0x00000000 [0001.459] I> 44) Base:0x00000000 Size:0x00000000 [0001.463] I> 45) Base:0x00000000 Size:0x00000000 [0001.467] GIC-SPI Target CPU: 0 [0001.470] Interrupts Init done [0001.473] calling constructors [0001.476] initializing heap [0001.479] I> Heap: [0xa0699b80 ... 0xab000000] [0001.483] initializing threads [0001.486] initializing timers [0001.489] creating bootstrap completion thread [0001.493] top of bootstrap2() [0001.496] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000 [0001.501] initializing platform [0001.503] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0001.509] W> device prod register failed [0001.513] I> Bl_dtb @0xaaf00000 [0001.519] W> "plugin-manager" doesn't exist, creating [0001.521] W> "ids" doesn't exist, creating [0001.525] W> "connection" doesn't exist, creating [0001.529] W> "configs" doesn't exist, creating [0001.542] E> failed to read label property for node 227172: 13 [0001.545] E> failed to read reg property for node 227260: 13 [0001.548] E> failed to read label property for node 227312: 13 [0001.552] E> failed to read label property for node 227380: 13 [0001.557] E> failed to read label property for node 227416: 13 [0001.563] E> failed to read label property for node 227452: 13 [0001.568] E> failed to read reg property for node 227520: 13 [0001.574] E> failed to read label property for node 227572: 13 [0001.580] I> Find /i2c@3160000's alias i2c0 [0001.583] I> Reading eeprom i2c=0 address=0x50 [0001.612] I> Device at /i2c@3160000:0x50 [0001.612] I> Reading eeprom i2c=0 address=0x56 [0001.637] I> Device at /i2c@3160000:0x56 [0001.638] I> Find /i2c@3180000's alias i2c2 [0001.638] I> Reading eeprom i2c=2 address=0x54 [0001.640] E> I2C: slave not found in slaves. [0001.640] E> I2C: Could not write 0 bytes to slave: 0x00a8 with repeat start true. [0001.641] E> I2C_DEV: Failed to send register address 0x00000000. [0001.642] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa8 at 0x00000000 via instance 2. [0001.651] E> eeprom: Failed to read I2C slave device [0001.656] I> Eeprom read failed 0x3526070d [0001.660] I> Reading eeprom i2c=2 address=0x57 [0001.664] E> I2C: slave not found in slaves. [0001.668] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0001.676] E> I2C_DEV: Failed to send register address 0x00000000. [0001.681] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 2. [0001.691] E> eeprom: Failed to read I2C slave device [0001.696] I> Eeprom read failed 0x3526070d [0001.700] I> Reading eeprom i2c=2 address=0x52 [0001.704] E> I2C: slave not found in slaves. [0001.708] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.716] E> I2C_DEV: Failed to send register address 0x00000000. [0001.721] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 2. [0001.731] E> eeprom: Failed to read I2C slave device [0001.736] I> Eeprom read failed 0x3526070d [0001.741] I> Find /i2c@c240000's alias i2c1 [0001.744] I> Reading eeprom i2c=1 address=0x52 [0001.749] E> I2C: slave not found in slaves. [0001.752] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.760] E> I2C_DEV: Failed to send register address 0x00000000. [0001.766] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.775] E> eeprom: Retry to read I2C slave device. [0001.780] E> I2C: slave not found in slaves. [0001.784] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.792] E> I2C_DEV: Failed to send register address 0x00000000. [0001.797] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.807] E> eeprom: Failed to read I2C slave device [0001.812] I> Eeprom read failed 0x3526070d [0001.816] I> Reading eeprom i2c=1 address=0x50 [0001.820] E> I2C: slave not found in slaves. [0001.824] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.832] E> I2C_DEV: Failed to send register address 0x00000000. [0001.837] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.847] E> eeprom: Retry to read I2C slave device. [0001.852] E> I2C: slave not found in slaves. [0001.856] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.864] E> I2C_DEV: Failed to send register address 0x00000000. [0001.869] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.879] E> eeprom: Failed to read I2C slave device [0001.884] I> Eeprom read failed 0x3526070d [0001.888] I> create_pm_ids: id: 2888-0004-400-M, len: 15 [0001.893] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.904] I> create_pm_ids: id: 2822-0000-700-K, len: 15 [0001.909] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.920] I> Adding plugin-manager/ids/2888-0004-400=/i2c@3160000:module@0x50 [0001.928] W> "i2c@3160000" doesn't exist, creating [0001.932] W> "module@0x50" doesn't exist, creating [0001.937] I> Adding plugin-manager/ids/2822-0000-700=/i2c@3160000:module@0x56 [0001.943] W> "module@0x56" doesn't exist, creating [0001.949] I> Adding plugin-manager/cvm [0001.952] W> "chip-id" doesn't exist, creating [0001.956] I> Adding plugin-manager/chip-id/A02P [0001.960] I> Plugin-manager override starting [0001.965] I> node /plugin-manager/fragement-tegra-wdt-en matches [0001.974] I> node /plugin-manager/fragement-soft-wdt matches [0001.981] I> node /plugin-manager/fragment-pcie-c5-rp matches [0001.985] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0001.996] I> Disable plugin-manager status in FDT [0001.997] I> Plugin-manager override finished successfully [0001.997] I> gpio framework initialized [0002.002] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver [0002.010] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver [0002.016] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 [0002.023] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.031] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.038] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.044] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 [0002.051] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.059] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.066] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.073] I> fixed regulator driver initialized [0002.085] I> register 'maxim' power off handle [0002.086] I> virtual i2c enabled [0002.086] I> registered 'maxim,max20024' pmic [0002.088] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver [0002.094] I> Boot-device: eMMC [0002.097] I> Boot_device: SDMMC_BOOT instance: 3 [0002.106] I> sdmmc-3 params source = boot args [0002.106] I> create_pm_ids: id: 2888-0004-400-M, len: 15 [0002.111] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.122] I> create_pm_ids: id: 2822-0000-700-K, len: 15 [0002.127] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.138] I> sdmmc bdev is already initialized [0002.143] I> sdmmc-3 params source = boot args [0002.173] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0002.186] I> Found 42 partitions in SDMMC_USER (instance 3) [0002.195] I> enabling 'vdd-hdmi-5v0' regulator [0002.201] I> regulator 'vdd-hdmi-5v0' already enabled [0002.201] I> hdmi cable connected [0002.203] W> set volts not configured for 'vdd-1v0' [0002.205] W> set volts not configured for 'vdd-1v8-hs' [0002.205] I> retrieved tmds range from prod_list_hdmi_soc [0002.209] E> invalid display type [0002.213] E> invalid display type [0002.215] E> cannot find any other nvdisp nodes [0002.230] I> edid read success [0002.242] I> edid read success [0002.243] I> width = 640, height = 480, frequency = 25174825 [0002.243] I> width = 1920, height = 1080, frequency = 148500000 [0002.243] I> width = 1920, height = 1080, frequency = 148500000 [0002.244] I> width = 1920, height = 1080, frequency = 148351648 [0002.244] I> width = 1920, height = 1080, frequency = 148351648 [0002.249] I> width = 1280, height = 720, frequency = 74175824 [0002.254] I> width = 1280, height = 720, frequency = 74175824 [0002.260] I> width = 720, height = 480, frequency = 26973026 [0002.265] I> width = 720, height = 480, frequency = 26973026 [0002.271] I> width = 720, height = 576, frequency = 26973026 [0002.276] I> width = 720, height = 576, frequency = 26973026 [0002.282] I> width = 640, height = 480, frequency = 25174825 [0002.287] I> Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.297] I> hdmi_enable, starting HDMI initialisation [0002.303] I> hdmi_enable, HDMI initialisation complete [0002.313] I> Load in CBoot Boot Options partition and parse it [0002.320] E> Error -9 when finding node with path /boot-configuration [0002.320] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO file. [0002.323] I> Using default boot order [0002.326] I> boot-dev-order :- [0002.329] I> 1.sd [0002.331] I> 2.usb [0002.333] I> 3.nvme [0002.335] I> 4.emmc [0002.337] I> 5.net [0002.339] I> Hit any key to stop autoboot: 4 3 2 1 [0004.346] initializing target [0004.346] calling apps_init() [0004.347] starting app kernel_boot_app [0004.366] I> found decompressor handler: lz4-legacy [0004.367] I> decompressing BMP blob ... [0004.377] I> Kernel type = Normal [0004.377] I> ########## SD (0) boot ########## [0004.378] I> No sdcard [0004.378] I> -0 params source = [0004.378] E> Blockdev open: exit error [0004.378] E> SD boot failed, err: 724238353 [0004.379] I> ########## USB (0) boot ########## [0004.384] W> No valid slot number is found in scratch register [0004.384] W> Return default slot: _a [0004.392] I> Validate XUSB-FW ... [0004.392] I> T19x: Authenticate XUSB-FW (bin_type: 11), max size 0x28000 [0004.397] I> Encryption fuse is not ON [0004.399] I> USB Firmware Version: 60.09 release [0004.459] I> regulator of usb2-0 already enabled [0004.466] I> regulator of usb2-1 already enabled [0004.473] I> regulator of usb2-2 already enabled [0004.483] I> enabling 'vdd-5v-sata' regulator [0005.551] I> USB 2.0 port 4 new high-speed USB device detected [0005.552] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4ad2000, cmd_ring.dma = 0xa4ad20c0 [0005.653] I> Start to enumerate device [0005.654] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4ad2000, cmd_ring.dma = 0xa4ad20c0 [0005.659] I> [0005.659] I> Enumerated USB Device 05e3:0610 [0005.660] I> [0005.661] I> Hub: [0005.661] I> Downstream ports : 4 [0005.661] I> Power switching : Ganged [0005.662] I> Compound device : No [0005.662] I> Over-current protection : Global [0005.666] I> Hub avg delay : 4 ns [0005.670] I> Set interface = 1 (alt setting) [0005.675] I> Enable hub ports [0005.679] W> handle_transfer_event: WARNING: Command was not successfully completed (0x04) [0008.740] W> xusbh_wait_irq: Timed out! status = 0x00 [0011.748] W> xusbh_wait_irq: Timed out! status = 0x00 [0011.748] E> Failed to set power feature for port 4 [0011.749] E> Failed to initialize hub [0011.749] E> failed to start xhci controller [0011.749] E> Error in init of XUSB host driver, err: 7979000c [0011.750] W> Failed to initialize device 5-0 [0011.750] E> USB boot failed, err: 2037973004 [0011.754] I> ########## NVME (0) boot ########## [0011.758] I> Initializing nvme device instance 0 [0011.763] I> Initializing nvme controller [0011.767] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000 [0011.773] I> vpcie3v3-supply not found [0011.777] I> vpcie12v-supply not found [0011.780] W> Failed to get nvidia,plat-gpios [0011.784] I> tegrabl_pcie_soc_preinit: (0): [0011.788] I> Unpowergate [0011.791] I> tegrabl_car_clk_disable(0) ... [0011.795] I> tegrabl_car_rst_set(CORE, 0) ... [0011.799] I> tegrabl_car_rst_set(APB, 0) ... [0011.803] I> tegrabl_car_clk_enable(0) ... [0011.807] I> tegrabl_car_rst_clear(APB, 0) ... [0011.811] I> tegrabl_set_ctrl_state(0) [0011.815] I> CLR PCIE_APB:6 [0011.818] I> tegrabl_pcie_soc_init: (0): [0011.821] I> APPL initialization ... [0011.825] I> poweron phys [0011.827] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000 [0011.834] I> tegrabl_power_on_phy: power on phy @0x3e30000 [0011.839] I> tegrabl_power_on_phy: power on phy @0x3e40000 [0011.844] I> tegrabl_power_on_phy: power on phy @0x3e50000 [0011.850] I> tegrabl_power_on_phy: power on phy @0x3e60000 [0012.955] C> Failed to link up controller-0 [0012.956] W> Failed tegrabl_pcie_soc_init(), error=0x12 [0012.956] I> Failed to initialize SoC Host PCIe controller [0012.956] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(0); error=0x12 [0012.957] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0012.957] W> Failed to open NVME-0, err = 80800612 [0012.962] W> Failed to initialize device 10-0 [0012.966] E> NVME (0) boot failed, err: 0x80800612 [0012.971] I> ########## NVME (1) boot ########## [0012.975] I> Initializing nvme device instance 1 [0012.980] I> Initializing nvme controller [0012.984] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14100000 [0012.990] I> vpcie3v3-supply not found [0012.994] I> vpcie12v-supply not found [0012.997] W> Failed to get nvidia,plat-gpios [0013.001] I> tegrabl_pcie_soc_preinit: (1): [0013.005] I> Unpowergate [0013.008] I> tegrabl_car_clk_disable(1) ... [0013.012] I> tegrabl_car_rst_set(CORE, 1) ... [0013.016] I> tegrabl_car_rst_set(APB, 1) ... [0013.020] I> tegrabl_car_clk_enable(1) ... [0013.024] I> tegrabl_car_rst_clear(APB, 1) ... [0013.028] I> tegrabl_set_ctrl_state(1) [0013.032] I> CLR PCIE_APB:6 [0013.035] I> tegrabl_pcie_soc_init: (1): [0013.038] I> APPL initialization ... [0013.042] I> poweron phys [0013.044] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14100000 [0013.051] I> tegrabl_power_on_phy: power on phy @0x3e10000 [0013.157] I> PCIe controller-1 link is up [0013.158] I> tegra_pcie_info[1].cfg0_base = 0x30000000 [0013.158] I> tegra_pcie_info[1].cfg1_base = 0x30020000 [0013.158] I> tegra_pcie_info[1].atu_dma_base = 0x30040000 [0013.159] I> tegra_pcie_bus[1].mem = 0x30200000 [0013.159] I> Scanning busnr: 0 devfn: 0 [0013.159] I> PCIe IDs: 0x1ad210de [0013.162] I> PCIe RID_CC: 0x60400a1 [0013.166] I> Scanning busnr: 1 devfn: 0 [0013.169] I> PCIe IDs: 0x91711b4b [0013.173] I> PCIe RID_CC: 0x1060113 [0013.176] I> PCI Config: I/O=0x30100000, Memory=0x30200000 [0013.181] I> IO bar_num=0 bar=0x30100000 [0013.185] I> IO bar_num=1 bar=0x30100008 [0013.189] I> IO bar_num=2 bar=0x30100010 [0013.193] I> IO bar_num=3 bar=0x30100018 [0013.196] I> IO bar_num=4 bar=0x30100020 [0013.200] I> MEM bar_num=5 bar=0x30200000 [0013.204] I> Number of PCIe devices detected: 2 [0013.208] E> tegrabl_nvme_init: Failed tegrabl_pcie_get_dev(1); error=0x0 [0013.215] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0013.221] W> Failed to open NVME-1, err = 80800612 [0013.226] W> Failed to initialize device 10-1 [0013.230] E> NVME (1) boot failed, err: 0x80800612 [0013.235] I> ########## NVME (2) boot ########## [0013.239] I> Initializing nvme device instance 2 [0013.244] I> Initializing nvme controller [0013.248] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14120000 [0013.254] I> vpcie3v3-supply not found [0013.258] I> vpcie12v-supply not found [0013.261] W> Failed to get nvidia,plat-gpios [0013.265] I> tegrabl_pcie_soc_preinit: (2): [0013.269] I> Unpowergate [0013.272] I> tegrabl_car_clk_disable(2) ... [0013.276] I> tegrabl_car_rst_set(CORE, 2) ... [0013.280] I> tegrabl_car_rst_set(APB, 2) ... [0013.284] I> tegrabl_car_clk_enable(2) ... [0013.288] I> tegrabl_car_rst_clear(APB, 2) ... [0013.292] I> tegrabl_set_ctrl_state(2) [0013.296] I> CLR PCIE_APB:6 [0013.299] I> tegrabl_pcie_soc_init: (2): [0013.302] I> APPL initialization ... [0013.306] I> poweron phys [0013.308] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14120000 [0013.315] I> tegrabl_power_on_phy: controller 2 not available [0013.320] E> Failed to power on phy on controller-2 [0013.325] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0013.330] I> Failed to initialize SoC Host PCIe controller [0013.335] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(2); error=0x1 [0013.342] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0013.348] W> Failed to open NVME-2, err = 80800601 [0013.353] W> Failed to initialize device 10-2 [0013.357] E> NVME (2) boot failed, err: 0x80800601 [0013.362] I> ########## NVME (3) boot ########## [0013.366] I> Initializing nvme device instance 3 [0013.370] I> Initializing nvme controller [0013.375] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14140000 [0013.381] I> vpcie3v3-supply not found [0013.384] I> vpcie12v-supply not found [0013.388] W> Failed to get nvidia,plat-gpios [0013.392] I> tegrabl_pcie_soc_preinit: (3): [0013.396] I> Unpowergate [0013.399] I> tegrabl_car_clk_disable(3) ... [0013.402] I> tegrabl_car_rst_set(CORE, 3) ... [0013.407] I> tegrabl_car_rst_set(APB, 3) ... [0013.411] I> tegrabl_car_clk_enable(3) ... [0013.415] I> tegrabl_car_rst_clear(APB, 3) ... [0013.419] I> tegrabl_set_ctrl_state(3) [0013.423] I> CLR PCIE_APB:6 [0013.425] I> tegrabl_pcie_soc_init: (3): [0013.429] I> APPL initialization ... [0013.432] I> poweron phys [0013.435] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14140000 [0013.441] I> tegrabl_power_on_phy: power on phy @0x3e80000 [0014.547] C> Failed to link up controller-3 [0014.547] W> Failed tegrabl_pcie_soc_init(), error=0x12 [0014.548] I> Failed to initialize SoC Host PCIe controller [0014.548] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(3); error=0x12 [0014.549] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0014.549] W> Failed to open NVME-3, err = 80800612 [0014.554] W> Failed to initialize device 10-3 [0014.558] E> NVME (3) boot failed, err: 0x80800612 [0014.562] I> ########## NVME (4) boot ########## [0014.567] I> Initializing nvme device instance 4 [0014.571] I> Initializing nvme controller [0014.576] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14160000 [0014.582] I> vpcie3v3-supply not found [0014.585] I> vpcie12v-supply not found [0014.589] W> Failed to get nvidia,plat-gpios [0014.593] I> tegrabl_pcie_soc_preinit: (4): [0014.597] I> Unpowergate [0014.599] I> tegrabl_car_clk_disable(4) ... [0014.603] I> tegrabl_car_rst_set(CORE, 4) ... [0014.608] I> tegrabl_car_rst_set(APB, 4) ... [0014.612] I> tegrabl_car_clk_enable(4) ... [0014.616] I> tegrabl_car_rst_clear(APB, 4) ... [0014.620] I> tegrabl_set_ctrl_state(4) [0014.623] I> CLR PCIE_APB:6 [0014.626] I> tegrabl_pcie_soc_init: (4): [0014.630] I> APPL initialization ... [0014.633] I> poweron phys [0014.636] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14160000 [0014.642] I> tegrabl_power_on_phy: controller 4 not available [0014.648] E> Failed to power on phy on controller-4 [0014.653] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0014.657] I> Failed to initialize SoC Host PCIe controller [0014.663] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(4); error=0x1 [0014.669] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0014.676] W> Failed to open NVME-4, err = 80800601 [0014.680] W> Failed to initialize device 10-4 [0014.684] E> NVME (4) boot failed, err: 0x80800601 [0014.689] I> ########## NVME (5) boot ########## [0014.693] I> Initializing nvme device instance 5 [0014.698] I> Initializing nvme controller [0014.702] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x141a0000 [0014.708] I> i=0, reg_phandle=0x1b [0014.714] I> reg_voltage=3300000 [0014.714] I> tegrabl_pcie_enable_regulators: regulator_set_voltage(0x1b, 3300000) [0014.726] I> enabling 'vdd-3v3-pcie' regulator [0014.727] I> i=1, reg_phandle=0x1c [0014.732] I> reg_voltage=1200000 [0014.732] I> tegrabl_pcie_enable_regulators: regulator_set_voltage(0x1c, 1200000) [0014.744] I> enabling 'vdd-12v-pcie' regulator [0014.745] I> tegrabl_pcie_soc_preinit: (5): [0014.748] I> Unpowergate [0014.751] I> tegrabl_car_clk_disable(5) ... [0014.755] I> tegrabl_car_rst_set(CORE, 5) ... [0014.759] I> tegrabl_car_rst_set(APB, 5) ... [0014.763] I> tegrabl_car_clk_enable(5) ... [0014.767] I> tegrabl_car_rst_clear(APB, 5) ... [0014.771] I> tegrabl_set_ctrl_state(5) [0014.775] I> CLR PCIE_APB:6 [0014.777] I> tegrabl_pcie_soc_init: (5): [0014.781] I> APPL initialization ... [0014.784] I> poweron phys [0014.787] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x141a0000 [0014.793] I> tegrabl_power_on_phy: power on phy @0x3eb0000 [0014.799] I> tegrabl_power_on_phy: power on phy @0x3ec0000 [0014.804] I> tegrabl_power_on_phy: power on phy @0x3ed0000 [0014.809] I> tegrabl_power_on_phy: power on phy @0x3ee0000 [0014.815] I> tegrabl_power_on_phy: power on phy @0x3ef0000 [0014.820] I> tegrabl_power_on_phy: power on phy @0x3f00000 [0014.825] I> tegrabl_power_on_phy: power on phy @0x3f10000 [0014.831] I> tegrabl_power_on_phy: power on phy @0x3f20000 [0015.936] C> Failed to link up controller-5 [0015.937] W> Failed tegrabl_pcie_soc_init(), error=0x12 [0015.937] I> Failed to initialize SoC Host PCIe controller [0015.937] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(5); error=0x12 [0015.938] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0015.938] W> Failed to open NVME-5, err = 80800612 [0015.943] W> Failed to initialize device 10-5 [0015.947] E> NVME (5) boot failed, err: 0x80800612 [0015.952] I> ########## Fixed storage boot ########## [0015.957] I> Loading kernel-bootctrl from partition [0015.962] I> Loading partition kernel-bootctrl at 0xa4b30000 from device(0x1) [0015.975] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0015.976] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0015.989] I> Already published: 00010003 [0015.989] I> Look for boot partition [0015.990] I> Fallback: assuming 0th partition is boot partition [0015.995] I> Detect filesystem [0016.023] I> Loading extlinux.conf ... [0016.023] I> Loading extlinux.conf binary from rootfs ... [0016.023] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf [0016.078] I> Loading extlinux.conf sig file from rootfs ... [0016.078] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf.sig [0016.121] I> overload load_size to 864 (from 1199) [0016.122] I> Validate extlinux.conf ... [0016.122] I> T19x: Authenticate extlinux.conf (bin_type: 54), max size 0x2000 [0016.123] E> digest on binary did not match!! [0016.123] C> OEM authentication of extlinux.conf payload failed! [0016.123] W> Failed to validate extlinux.conf binary from rootfs (err=1077936152, fail=0) [0016.130] W> Security fuse not burned, ignore validation failure [0016.136] I> restore load_size to 1199 [0016.139] I> L4T boot options [0016.142] I> [1]: "primary kernel" [0016.145] I> [2]: "primary kernel" [0016.148] I> Enter choice: [0019.152] I> Continuing with default option: 2 [0019.152] I> Loading kernel ... [0019.152] I> Loading kernel binary from rootfs ... [0019.153] I> rootfs path: /sdmmc_user/boot/vmlinuz-5.2.21-844084-gfb7cc7d79a6f-dirty [0019.299] I> Loading kernel sig file from rootfs ... [0019.300] I> rootfs path: /sdmmc_user/boot/vmlinuz-5.2.21-844084-gfb7cc7d79a6f-dirty.sig [0019.325] I> ext2_walk:142: 'vmlinuz-5.2.21-844084-gfb7cc7d79a6f-dirty.sig' lookup failed [0019.325] I> ext4_open_file:666: '/boot/vmlinuz-5.2.21-844084-gfb7cc7d79a6f-dirty.sig' lookup failed [0019.326] E> file /sdmmc_user/boot/vmlinuz-5.2.21-844084-gfb7cc7d79a6f-dirty.sig open failed!! [0019.326] W> Failed to load kernel sig file (err=202113041) [0019.330] I> Validate kernel ... [0019.334] I> T19x: Authenticate kernel (bin_type: 37), max size 0x5000000 [0019.340] E> Stage2Signature validation failed with SHA2!! [0019.346] C> OEM authentication of kernel header failed! [0019.351] W> Failed to validate kernel binary from rootfs (err=1077936152, fail=1) [0019.358] W> Security fuse not burned, ignore validation failure [0019.364] I> restore load_size to 20861440 [0019.378] I> Loading kernel-dtb ... [0019.378] I> No kernel-dtb binary path [0019.379] I> Continue to load from partition ... [0019.379] W> No valid slot number is found in scratch register [0019.385] W> Return default slot: _a [0019.388] I> A/B: bin_type (38) slot 0 [0019.392] I> Loading kernel-dtb from partition [0019.396] I> Loading partition kernel-dtb at 0x91000000 from device(0x1) [0019.412] I> Validate kernel-dtb ... [0019.412] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x400000 [0019.413] I> Encryption fuse is not ON [0019.419] I> Loading ramdisk from rootfs ... [0019.421] I> Loading ramdisk binary from rootfs ... [0019.426] I> rootfs path: /sdmmc_user/boot/initrd.img-5.2.21-844084-gfb7cc7d79a6f-dirty [0019.600] I> Loading ramdisk sig file from rootfs ... [0019.600] I> rootfs path: /sdmmc_user/boot/initrd.img-5.2.21-844084-gfb7cc7d79a6f-dirty.sig [0019.625] I> ext2_walk:142: 'initrd.img-5.2.21-844084-gfb7cc7d79a6f-dirty.sig' lookup failed [0019.626] I> ext4_open_file:666: '/boot/initrd.img-5.2.21-844084-gfb7cc7d79a6f-dirty.sig' lookup failed [0019.626] E> file /sdmmc_user/boot/initrd.img-5.2.21-844084-gfb7cc7d79a6f-dirty.sig open failed!! [0019.627] W> Failed to load ramdisk sig file (err=202113041) [0019.632] I> Validate ramdisk ... [0019.635] I> T19x: Authenticate ramdisk (bin_type: 54), max size 0x4000000 [0019.642] E> Stage2Signature validation failed with SHA2!! [0019.647] C> OEM authentication of ramdisk header failed! [0019.652] W> Failed to validate ramdisk binary from rootfs (err=1077936152, fail=1) [0019.660] W> Security fuse not burned, ignore validation failure [0019.666] I> restore load_size to 23967916 [0019.681] I> Kernel hdr @0xa4b30000 [0019.681] I> Kernel dtb @0x90000000 [0019.681] I> decompressor handler not found [0019.681] I> Copying kernel image (20861440 bytes) from 0xa4b30000 to 0x80080000 ... [0019.694] I> Done [0019.694] I> Updated bpmp info to DTB [0019.694] I> Ramdisk: Base: 0x92000000; Size: 0x16db8ac [0019.698] I> Updated initrd info to DTB [0019.702] W> WARN: Fail to override "console=none" in commandline [0019.708] I> Active rootfs suffix: [0019.711] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0019.718] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0019.726] W> No valid slot number is found in scratch register [0019.731] W> Return default slot: _a [0019.735] I> Active slot suffix: [0019.738] I> add_boot_slot_suffix: slot_suffix = [0019.742] I> Linux Cmdline: console=ttyS0,115200n8 video=tegrafb earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt rootfs.slot_suffix= tegra_fbmem=0x800000@0xa06aa000 lut_mem=0x2008@0xa06a5000 usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=8 boot.slot_suffix= boot.ratchetvalues=0.4.2 vpr_resize sdhci_tegra.en_boot_part_access=1 [0019.772] I> Updated bootarg info to DTB [0019.776] W> MAC addr invalid! [0019.778] E> Failed to get WIFI MAC address [0019.782] W> MAC addr invalid! [0019.785] E> Failed to get Bluetooth MAC address [0019.790] I> eeprom_get_mac_addr: MAC (type: 2): 48:b0:2d:3a:a5:68 [0019.796] W> "plugin-manager" doesn't exist, creating [0019.801] I> Adding /chosen/plugin-manager/cvm [0019.805] W> "chip-id" doesn't exist, creating [0019.809] I> Adding /chosen/plugin-manager/chip-id [0019.814] W> "configs" doesn't exist, creating [0019.818] I> Adding /chosen/plugin-manager/configs [0019.823] W> "ids" doesn't exist, creating [0019.827] I> Adding /chosen/plugin-manager/ids [0019.831] W> "odm-data" doesn't exist, creating [0019.835] I> Adding /chosen/plugin-manager/odm-data [0019.841] W> "memory" doesn't exist, creating [0019.844] I> [0] START: 0x80000000, END: 0xac000000 [0019.849] I> [1] START: 0xac004000, END: 0xf0ad0000 [0019.854] I> [2] START: 0xf0adc000, END: 0xf0ae0000 [0019.859] I> dram_block larger than 80000000 [0019.863] I> [3] START: 0x100000000, END: 0x880000000 [0019.868] I> added [base:0x80000000, size:0x2c000000] to /memory [0019.873] I> added [base:0xac200000, size:0x44800000] to /memory [0019.879] I> added [base:0x100000000, size:0x780000000] to /memory [0019.885] I> Updated memory info to DTB [0019.889] W> "reserved-memory" doesn't exist, creating [0019.894] W> "fb0_carveout" doesn't exist, creating [0019.899] E> add_disp_param: failed to get display params for du=1 [0019.905] W> "reset" doesn't exist, creating [0019.909] I> Adding ecid(0000000164017147080000000d020240) to DT [0019.915] I> NVG: Logical CPU: 0; MPIDR: 0x80000000 [0019.919] I> NVG: Logical CPU: 1; MPIDR: 0x80000001 [0019.924] I> NVG: Logical CPU: 2; MPIDR: 0x80000100 [0019.929] I> NVG: Logical CPU: 3; MPIDR: 0x80000101 [0019.934] I> NVG: Logical CPU: 4; MPIDR: 0x80000200 [0019.938] I> NVG: Logical CPU: 5; MPIDR: 0x80000201 [0019.943] I> NVG: Logical CPU: 6; MPIDR: 0x80000300 [0019.948] I> NVG: Logical CPU: 7; MPIDR: 0x80000301 [0019.953] E> /cpus/cpu-map does not exist [0019.956] W> "arm-pmu" doesn't exist, creating [0019.961] W> "grid-of-semaphores" doesn't exist, creating [0019.966] W> "misc-data" doesn't exist, creating [0019.970] I> Boot-device: eMMC [0019.973] I> Add boot-sdmmc to plugin-manager/misc-data [0019.978] I> Add storage-sdmmc to plugin-manager/misc-data [0019.984] W> Unknown storage device [0019.987] I> Add serial number:1561221004864 as DT property [0019.993] I> Plugin-manager override starting [0019.997] W> Failed to find /plugin-manager in DT [0020.001] I> tegrabl_load_kernel_and_dtb: Done [0020.024] I> Kernel EP: 0x80080000, DTB: 0x90000000 ÿâWARNING: clk_get_rate: clk_power_ungate on gated domain 27 for gpcclk ÿá[ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring ÿâti2c_explain_err(5): Error status is 0x4000 ti2c_explain_err(5): Register dump... ti2c_explain_err(5): I2C_CNFG = 0x2c00 ti2c_explain_err(5): I2C_PACKET_TRANSFER_STATUS = 0x0 ti2c_explain_err(5): I2C_FIFO_CONTROL = 0x70000 ti2c_explain_err(5): I2C_FIFO_STATUS = 0x800000 ti2c_explain_err(5): I2C_INT_MASK = 0xec ti2c_explain_err(5): I2C_INT_STATUS = 0x82 ti2c_explain_err(5): msg->len - 1 ti2c_explain_err(5): is_msg_write - 1 ti2c_explain_err(5): buf_len - 0 fmon_disable: FMON_SOR2: detected fault 0x1