SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init ▒▒ [0000.420] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-feba5943) [0000.421] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0000.421] I> Default Heap @ [0xd486400 - 0xd48a400] [0000.422] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0000.428] W> device prod register failed [0000.432] I> Boot-device: QSPI [0000.435] I> Boot_device: QSPI_FLASH instance: 0 [0000.440] I> QSPI Flash Size = 32 MB [0000.445] I> Qspi initialized successfully [0000.446] I> qspi flash-0 params source = boot args [0000.771] I> sdmmc DDR50 mode [0000.773] I> sdmmc-3 params source = safe params [0000.778] I> Found 47 partitions in QSPI_FLASH (instance 0) [0000.779] W> Cannot find any partition table for 00000003 [0000.784] I> Found 11 partitions in SDMMC_USER (instance 3) [0000.785] W> No valid slot number is found in scratch register [0000.785] W> Return default slot: _a [0000.786] I> Active Boot chain : 0 [0000.787] I> parsing oem signed section of bpmp-fw header done [0000.787] I> bpmp-fw binary init read from storage [0000.795] I> RSA PSS signature check: OK [0000.796] I> oem authentication of bpmp-fw header done [0000.810] I> bpmp-fw binary done read from storage [0000.811] I> bpmp-fw: Authentication init Done [0000.812] I> parsing oem signed section of cpubl header done [0000.815] I> cpubl binary init read from storage [0000.824] I> bpmp-fw: Authentication Finalize Done [0000.826] I> RSA PSS signature check: OK [0000.828] I> oem authentication of cpubl header done [0000.836] I> cpubl binary done read from storage [0000.837] I> cpubl: Authentication init Done [0000.842] I> parsing oem signed section of rce header done [0000.847] I> rce binary init read from storage [0000.851] I> Relocating BR-BCT [0000.856] I> cpubl: Authentication Finalize Done [0000.861] I> RSA PSS signature check: OK [0000.862] I> oem authentication of rce header done [0000.867] I> rce binary done read from storage [0000.871] I> rce: Authentication init Done [0000.875] I> parsing oem signed section of ape header done [0000.880] I> ape binary init read from storage [0000.886] I> rce: Authentication Finalize Done [0000.891] I> RSA PSS signature check: OK [0000.893] I> oem authentication of ape header done [0000.897] I> ape binary done read from storage [0000.902] I> ape: Authentication init Done [0000.906] I> parsing oem signed section of tos header done [0000.911] I> tos binary init read from storage [0000.916] I> ape: Authentication Finalize Done [0000.922] I> RSA PSS signature check: OK [0000.923] I> oem authentication of tos header done [0000.930] I> tos binary done read from storage [0000.932] I> tos: Authentication init Done [0000.936] I> parsing oem signed section of bpmp-fw-dtb header done [0000.942] I> bpmp-fw-dtb binary init read from storage [0000.949] I> tos: Authentication Finalize Done [0000.955] I> RSA PSS signature check: OK [0000.956] I> oem authentication of bpmp-fw-dtb header done [0000.960] I> bpmp-fw-dtb binary done read from storage [0000.965] I> bpmp-fw-dtb: Authentication init Done [0000.971] I> parsing oem signed section of cpubl-dtb header done [0000.976] I> cpubl-dtb binary init read from storage [0000.982] I> bpmp-fw-dtb: Authentication Finalize Done [0001.040] I> RSA PSS signature check: OK [0001.041] I> oem authentication of cpubl-dtb header done [0001.042] I> cpubl-dtb binary done read from storage [0001.042] I> cpubl-dtb: Authentication init Done [0001.043] I> parsing oem signed section of eks header done [0001.044] I> eks binary init read from storage [0001.046] I> cpubl-dtb: Authentication Finalize Done [0001.051] I> RSA PSS signature check: OK [0001.052] I> oem authentication of eks header done [0001.057] I> eks binary done read from storage [0001.061] I> eks: Authentication init Done [0001.065] I> eks: Authentication Finalize Done [0001.069] I> EKB detected (length: 0x410) @ VA:0x52714400 ▒▒NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 14:42:47, Jan 15 2021 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 40: hwkey-agent is running!! hwkey-agent: 197: key_mgnt_processing ....... hwkey-agent: 189: Setting EKB key 0 to slot 14 hwkey-agent: 167: Init hweky-agent services!! luks-srv: 40: luks-srv is running!! luks-srv: 157: Init luks-srv IPC services!! platform_bootstrap_epilog: trusty bootstrap complete ▒▒ welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is e73a758761f0c6d24a1e69a2ac6b5035 tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized 391 clocks registered clk_mrq_init: mrq handler registered clk initialized nvlink initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform_init: bad clk id in clock@cluster1_avfs avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized uphy_mrq_init: mrq handler registered uphy_dt initialized uphy initialized safereg_init: period 80 ms ec_late initialized ▒▒ [0001.411] I> Welcome to Cboot▒▒mrq initialized WARNING: no registered clock for FMON_NAFLL_CLUSTER1 (id 281) fmon_post initialized ▒▒ [0001.411] I> Cboot Version: t194-9efcbc4f [0001.413] I> CPU-BL Params @ 0xf2820000 [0001.417] I> 0) Base:0x00000000 Size:0x00000000 [0001.421] I> 1) Base:0xf1100000 Size:0x00100000 [0001.425] I> 2) Base:0xf2000000 Size:0x00200000 [0001.430] I> 3) Base:0xf1200000 Size:0x00200000 ▒▒clk_set_parent failed for clk i2c2, parent pll_aon (-22) clk_set_parent failed for clk i2c8, parent pll_aon (-22) clk_dt_late initialized machine_check initialized pm_post initialized dbells initialized avfs_clk_platform_post initialized dmce initialized cvc initialized ccplex_avfs_hw_init: nafll_cluster0: not monitored ccplex_avfs_hw_init: nafll_cluster2: not monitored ccplex_avfs_hw_init: nafll_cluster3: not monitored avfs_clk_mach_post initialized regulator_post initialized rm initialized sc7_diag initialized thermal_test initialized serial_late initialized clk_post initialized clk_dt_post initialized mc_reg initialized pg_post initialized dyn_modules initialized sku_debugfs initialized speedo_debugfs initialized adc_debugfs initialized Failed to register PTO counter for id 281 Failed to register PTO counter for id 281 Failed to register PTO counter for id 281 Failed to register PTO counter for id 281 clk_debugfs initialized emc_debugfs initialized dvs_debugfs initialized fmon_debugfs_init_one: no clock debugfs node to attach FMON_NAFLL_CLUSTER1 fmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized debugfs_cons initialized mail_fs initialized profile initialized cvc_debugfs initialized dmce_debugfs initialized ec_debugfs initialized rm_rail_debugfs_init: /rm/vdd_cpu: failed rm_rail_debugfs_init: /rm/vdd_cpu: failed rm_debugfs initialized soctherm_debug initialized gr_reader initialized mods initialized dt_fs initialized debugfs_mrq initialized debug_mrq initialized debug_safereg initialized initializing target calling apps_init() starting app shell entering main console loop ] ▒▒[0001.434] I> 4) Base:0xf1000000 Size:0x00100000 [0001.589] I> 5) Base:0xf0f00000 Size:0x00100000 [0001.593] I> 6) Base:0xf3800000 Size:0x00400000 [0001.597] I> 7) Base:0xf1c00000 Size:0x00400000 [0001.602] I> 8) Base:0xf0e00000 Size:0x00100000 [0001.606] I> 9) Base:0xf0d00000 Size:0x00100000 [0001.611] I> 10) Base:0xf3000000 Size:0x00800000 [0001.615] I> 11) Base:0x40000000 Size:0x00040000 [0001.620] I> 12) Base:0xf0c00000 Size:0x00100000 [0001.624] I> 13) Base:0x40046000 Size:0x00002000 [0001.629] I> 14) Base:0x40048000 Size:0x00002000 [0001.633] I> 15) Base:0xac000000 Size:0x00004000 [0001.638] I> 16) Base:0x4004a000 Size:0x00002000 [0001.642] I> 17) Base:0xf0b00000 Size:0x00100000 [0001.647] I> 18) Base:0x4004c000 Size:0x00002000 [0001.651] I> 19) Base:0xf2200000 Size:0x00600000 [0001.655] I> 20) Base:0x4004e000 Size:0x00002000 [0001.660] I> 21) Base:0xf0ad0000 Size:0x0000c000 [0001.664] I> 22) Base:0x00000000 Size:0x00000000 [0001.669] I> 23) Base:0xf0ae0000 Size:0x00020000 [0001.673] I> 24) Base:0xf6000000 Size:0x02000000 [0001.678] I> 25) Base:0x40050000 Size:0x00002000 [0001.682] I> 26) Base:0x40040000 Size:0x00006000 [0001.687] I> 27) Base:0xf1800000 Size:0x00400000 [0001.691] I> 28) Base:0xf4c00000 Size:0x01400000 [0001.696] I> 29) Base:0xf1400000 Size:0x00400000 [0001.700] I> 30) Base:0x00000000 Size:0x00000000 [0001.705] I> 31) Base:0x00000000 Size:0x00000000 [0001.709] I> 32) Base:0xf8000000 Size:0x08000000 [0001.713] I> 33) Base:0x00000000 Size:0x00000000 [0001.718] I> 34) Base:0xf3c00000 Size:0x01000000 [0001.722] I> 35) Base:0xab000000 Size:0x01000000 [0001.727] I> 36) Base:0xa0000000 Size:0x0b000000 [0001.731] I> 37) Base:0xf2800000 Size:0x00800000 [0001.736] I> 38) Base:0x80000000 Size:0x20000000 [0001.740] I> 39) Base:0xb0000000 Size:0x08000000 [0001.745] I> 40) Base:0x00000000 Size:0x00000000 [0001.749] I> 41) Base:0x00000000 Size:0x00000000 [0001.754] I> 42) Base:0x00000000 Size:0x00000000 [0001.758] I> 43) Base:0x00000000 Size:0x00000000 [0001.763] I> 44) Base:0x00000000 Size:0x00000000 [0001.767] I> 45) Base:0x00000000 Size:0x00000000 [0001.771] GIC-SPI Target CPU: 0 [0001.774] Interrupts Init done [0001.777] calling constructors [0001.780] initializing heap [0001.783] I> Heap: [0xa06945e8 ... 0xab000000] [0001.787] initializing threads [0001.790] initializing timers [0001.793] creating bootstrap completion thread [0001.797] top of bootstrap2() [0001.800] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000 [0001.805] initializing platform [0001.808] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0001.813] W> device prod register failed [0001.817] I> Bl_dtb @0xaaf00000 [0001.822] W> "plugin-manager" doesn't exist, creating [0001.825] W> "ids" doesn't exist, creating [0001.829] W> "connection" doesn't exist, creating [0001.833] W> "configs" doesn't exist, creating [0001.845] I> Find /i2c@3160000's alias i2c0 [0001.845] I> Reading eeprom i2c=0 address=0x50 [0001.871] I> Device at /i2c@3160000:0x50 [0001.871] I> create_pm_ids: id: 3668-0001-200-G, len: 15 [0001.872] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.873] I> Adding plugin-manager/ids/3668-0001-200=/i2c@3160000:module@0x50 [0001.874] W> "i2c@3160000" doesn't exist, creating [0001.878] W> "module@0x50" doesn't exist, creating [0001.885] I> Adding plugin-manager/cvm [0001.886] W> "chip-id" doesn't exist, creating [0001.890] I> Adding plugin-manager/chip-id/A02P [0001.895] I> Plugin-manager override starting [0001.900] I> node /plugin-manager/fragement-tegra-wdt-en matches [0001.909] I> Disable plugin-manager status in FDT [0001.909] I> Plugin-manager override finished successfully [0001.914] I> gpio framework initialized [0001.920] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver [0001.927] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver [0001.933] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 [0001.941] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0001.948] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0001.955] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0001.961] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 [0001.969] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0001.976] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0001.983] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0001.990] I> fixed regulator driver initialized [0001.999] I> register 'maxim' power off handle [0002.000] I> virtual i2c enabled [0002.000] I> registered 'maxim,max20024' pmic [0002.005] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver [0002.011] I> Boot-device: QSPI [0002.014] I> Boot_device: QSPI_FLASH instance: 0 [0002.019] I> QSPI source rate = 204000 Khz [0002.023] I> Requested rate for QSPI clock = 34000 Khz [0002.028] I> BPMP-set rate for QSPI clk = 34000 Khz [0002.033] I> QSPI Flash Size = 32 MB [0002.040] I> Qspi initialized successfully [0002.041] I> qspi flash-0 params source = boot args [0002.045] I> create_pm_ids: id: 3668-0001-200-G, len: 15 [0002.050] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.065] I> sdmmc-3 params source = safe params [0002.067] I> Found 47 partitions in QSPI_FLASH (instance 0) [0002.087] W> Cannot find any partition table for 00000003 [0002.099] I> Found 11 partitions in SDMMC_USER (instance 3) [0002.112] I> hdmi cable connected [0002.114] W> set volts not configured for 'vdd-1v0' [0002.116] W> set volts not configured for 'vdd-1v8-hs' [0002.120] E> invalid display type [0002.120] E> cannot find any other nvdisp nodes [0002.135] I> edid read success [0002.148] I> edid read success [0002.148] I> width = 640, height = 480, frequency = 25174825 [0002.149] I> width = 640, height = 480, frequency = 25174825 [0002.149] I> width = 1920, height = 1080, frequency = 148500000 [0002.150] I> width = 1920, height = 1080, frequency = 148500000 [0002.150] I> width = 1920, height = 1080, frequency = 148351648 [0002.154] I> width = 1920, height = 1080, frequency = 148351648 [0002.160] I> width = 1280, height = 720, frequency = 74175824 [0002.166] I> width = 1280, height = 720, frequency = 74175824 [0002.171] I> width = 720, height = 480, frequency = 26973026 [0002.177] I> width = 720, height = 576, frequency = 26973026 [0002.182] I> width = 720, height = 480, frequency = 26973026 [0002.188] I> width = 720, height = 576, frequency = 26973026 [0002.193] I> width = 640, height = 480, frequency = 25174825 [0002.199] I> Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.209] I> hdmi_enable, starting HDMI initialisation [0002.214] I> hdmi_enable, HDMI initialisation complete [0002.224] I> Load in CBoot Boot Options partition and parse it [0002.224] E> Error -9 when finding node with path /boot-configuration [0002.227] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO file. [0002.234] I> Using default boot order [0002.238] I> boot-dev-order :- [0002.241] I> 1.sd [0002.242] I> 2.usb [0002.244] I> 3.nvme [0002.246] I> 4.emmc [0002.248] I> 5.net [0002.250] I> Hit any key to stop autoboot: 4 3 2 1 [0004.258] initializing target [0004.258] calling apps_init() [0004.259] starting app kernel_boot_app [0004.269] I> found decompressor handler: lz4-legacy [0004.270] I> decompressing BMP blob ... [0004.283] I> Kernel type = Normal [0004.283] I> Loading kernel-bootctrl from partition [0004.283] I> Loading partition kernel-bootctrl at 0xa4ad0000 from device(0x1) [0004.301] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0004.302] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0004.303] I> ########## SD (0) boot ########## [0004.303] I> No sdcard [0004.303] I> -0 params source = [0004.303] E> Blockdev open: exit error [0004.304] E> SD boot failed, err: 724238353 [0004.308] I> ########## USB (0) boot ########## [0004.317] W> No valid slot number is found in scratch register [0004.318] W> Return default slot: _a [0004.329] I> USB Firmware Version: 60.06 release [0004.384] I> regulator of usb2-0 already enabled [0004.389] I> regulator of usb2-1 already enabled [0004.395] I> regulator of usb2-2 already enabled [0005.461] I> USB 2.0 port 2 new high-speed USB device detected [0005.463] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa9ad0000, cmd_ring.dma = 0xa9ad0040 [0005.564] I> Start to enumerate device [0005.565] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa9ad0000, cmd_ring.dma = 0xa9ad0040 [0005.570] I> [0005.570] I> Enumerated USB Device 0424:2513 [0005.570] I> [0005.571] I> Hub: [0005.572] I> Downstream ports : 3 [0005.572] I> Power switching : Ganged [0005.572] I> Compound device : No [0005.573] I> Over-current protection : Global [0005.577] I> Hub avg delay : 4 ns [0005.581] I> Set interface = 1 (alt setting) [0005.586] I> Enable hub ports [0006.606] E> No device found on any of the hub ports [0006.607] E> failed to start xhci controller [0006.607] E> Error in init of XUSB host driver, err: 7979000d [0006.607] W> Failed to initialize device 5-0 [0006.608] E> USB boot failed, err: 2037973005 [0006.608] I> ########## Fixed storage boot ########## [0006.609] I> Already published: 00010003 [0006.613] I> Look for boot partition [0006.616] I> Fallback: assuming 0th partition is boot partition [0006.622] I> Detect filesystem [0006.649] I> Loading extlinux.conf ... [0006.649] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf [0006.698] I> L4T boot options [0006.699] I> [1]: "primary kernel" [0006.699] I> Enter choice: [0009.700] I> Continuing with default option: 1 [0009.700] I> Loading kernel sig file from rootfs ... [0009.700] I> rootfs path: /sdmmc_user/boot/Image.sig [0009.731] I> Loading kernel binary from rootfs ... [0009.731] I> rootfs path: /sdmmc_user/boot/Image [0010.138] I> overload load_size to 34609160 (from 34609168) [0010.161] I> Validate kernel ... [0010.162] I> T19x: Authenticate kernel (bin_type: 37), max size 0x5000000 [0010.163] I> RSA PSS signature check: OK [0010.478] I> authenticate_oem_payload: Decrypt the binary [0010.723] I> No kernel-dtb binary path [0010.723] W> No valid slot number is found in scratch register [0010.724] W> Return default slot: _a [0010.724] I> A/B: bin_type (38) slot 0 [0010.724] I> Loading kernel-dtb from partition [0010.725] I> Loading partition kernel-dtb at 0x91000000 from device(0x1) [0010.736] I> Validate kernel-dtb ... [0010.736] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x400000 [0010.738] I> RSA PSS signature check: OK [0010.741] I> authenticate_oem_payload: Decrypt the binary [0010.747] I> Loading ramdisk from rootfs ... [0010.749] I> Loading initrd sig file from rootfs ... [0010.754] I> rootfs path: /sdmmc_user/boot/initrd.sig [0010.789] I> Loading initrd binary from rootfs ... [0010.789] I> rootfs path: /sdmmc_user/boot/initrd [0010.903] I> overload load_size to 7236790 (from 7236800) [0010.906] I> Validate initrd ... [0010.907] I> T19x: Authenticate initrd (bin_type: 49), max size 0x4000000 [0010.908] I> RSA PSS signature check: OK [0010.974] I> authenticate_oem_payload: Decrypt the binary [0011.035] I> Kernel hdr @0xa4ad0000 [0011.035] I> Kernel dtb @0x90000000 [0011.035] I> decompressor handler not found [0011.036] I> Copying kernel image (34609160 bytes) from 0xa4ad0000 to 0x80080000 ... [0011.046] I> Done [0011.047] I> Updated bpmp info to DTB [0011.048] I> Ramdisk: Base: 0x92000000; Size: 0x6e6cb6 [0011.048] I> Updated initrd info to DTB [0011.048] W> WARN: Fail to override "console=none" in commandline [0011.049] I> Active rootfs suffix: [0011.051] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0011.058] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0011.066] W> No valid slot number is found in scratch register [0011.071] W> Return default slot: _a [0011.075] I> Active slot suffix: [0011.078] I> add_boot_slot_suffix: slot_suffix = [0011.082] I> Linux Cmdline: console=ttyTCU0,115200 video=tegrafb no_console_suspend=1 earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt rootfs.slot_suffix= tegra_fbmem=0x800000@0xa069f000 lut_mem=0x2008@0xa069b000 usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=6 boot.slot_suffix= boot.ratchetvalues=0.4.2 vpr_resize sdhci_tegra.en_boot_part_access=1 [0011.114] I> Updated bootarg info to DTB [0011.117] W> MAC addr invalid! [0011.120] E> Failed to get WIFI MAC address [0011.124] W> MAC addr invalid! [0011.127] E> Failed to get Bluetooth MAC address [0011.132] I> eeprom_get_mac_addr: MAC (type: 2): 48:b0:2d:15:cd:e6 [0011.138] W> "plugin-manager" doesn't exist, creating [0011.143] I> Adding /chosen/plugin-manager/cvm [0011.147] W> "chip-id" doesn't exist, creating [0011.151] I> Adding /chosen/plugin-manager/chip-id [0011.156] W> "configs" doesn't exist, creating [0011.160] I> Adding /chosen/plugin-manager/configs [0011.165] W> "ids" doesn't exist, creating [0011.169] I> Adding /chosen/plugin-manager/ids [0011.173] W> "odm-data" doesn't exist, creating [0011.177] I> Adding /chosen/plugin-manager/odm-data [0011.185] W> "memory" doesn't exist, creating [0011.187] I> [0] START: 0x80000000, END: 0xac000000 [0011.191] I> [1] START: 0xac004000, END: 0xf0ad0000 [0011.196] I> [2] START: 0xf0adc000, END: 0xf0ae0000 [0011.200] I> dram_block larger than 80000000 [0011.205] I> [3] START: 0x100000000, END: 0x280000000 [0011.209] I> added [base:0x80000000, size:0x2c000000] to /memory [0011.215] I> added [base:0xac200000, size:0x44800000] to /memory [0011.221] I> added [base:0x100000000, size:0x180000000] to /memory [0011.228] I> Updated memory info to DTB [0011.231] E> add_disp_param: failed to get display params for du=1 [0011.237] W> "reset" doesn't exist, creating [0011.242] I> Adding ecid(00000001647c05c4080000000bff80c0) to DT [0011.247] I> NVG: Logical CPU: 0; MPIDR: 0x80000000 [0011.252] I> NVG: Logical CPU: 1; MPIDR: 0x80000001 [0011.256] I> NVG: Logical CPU: 2; MPIDR: 0x80000100 [0011.261] I> NVG: Logical CPU: 3; MPIDR: 0x80000101 [0011.266] I> NVG: Logical CPU: 4; MPIDR: 0x80000200 [0011.271] I> NVG: Logical CPU: 5; MPIDR: 0x80000201 [0011.275] I> Deleted cpu@6 node in DT [0011.279] I> Deleted cpu@7 node in DT [0011.282] I> Deleted cluster3 node in FDT [0011.286] I> Update arm-pmu in FDT [0011.289] I> - update property: interrupts [0011.293] I> - update property: interrupt-affinity [0011.299] W> "misc-data" doesn't exist, creating [0011.302] I> Boot-device: QSPI [0011.305] W> Unknown boot device [0011.308] I> Add storage-qspi to plugin-manager/misc-data [0011.314] W> Unknown storage device [0011.317] I> Add serial number:1424320084198 as DT property [0011.323] I> Plugin-manager override starting [0011.327] I> node /plugin-manager/fragement-tegra-wdt-en matches [0011.334] I> Disable plugin-manager status in FDT [0011.337] I> Plugin-manager override finished successfully [0011.343] I> tegrabl_load_kernel_and_dtb: Done [0011.365] I> Kernel EP: 0x80080000, DTB: 0x90000000 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (prod@ubuntu) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Thu Mar 18 20:17:56 CET 2021 [ 0.000000] Boot CPU: AArch64 Processor [4e0f0040] [ 0.000000] OF: fdt:memory scan node memory, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 2c000000 [ 0.000000] OF: fdt: - ac200000 , 44800000 [ 0.000000] OF: fdt: - 100000000 , 180000000 [ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '') [ 0.000000] bootconsole [tegra_comb_uart0] enabled [ 0.000000] Found tegra_fbmem: 00800000@a069f000 [ 0.000000] Found lut_mem: 00002008@a069b000