user@user-desktop:~$ dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-tegra-tegra (unisystem@unisystem-Z370P-D3) (gcc version 7.5.0 (Linaro GCC 7.5-2019.12) ) #6 SMP PREEMPT Thu Oct 14 12:08:51 CEST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00140000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] On node 0 totalpages: 1039872 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 519168 pages, LIFO batch:31 [ 0.000000] Normal zone: 8136 pages used for memmap [ 0.000000] Normal zone: 520704 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefb1000 s61592 r8192 d32616 u102400 [ 0.000000] pcpu-alloc: s61592 r8192 d32616 u102400 alloc=25*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29300(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3567240K/4159488K available (15358K kernel code, 2930K rwdata, 6716K rodata, 8576K init, 609K bss, 117112K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f80000 ( 15360 KB) [ 0.000000] .rodata : 0xffffff8008f80000 - 0xffffff8009620000 ( 6784 KB) [ 0.000000] .init : 0xffffff8009620000 - 0xffffff8009e80000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e80000 - 0xffffff800a15c808 ( 2931 KB) [ 0.000000] .bss : 0xffffff800a15c808 - 0xffffff800a1f4efc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.001651] Console: colour dummy device 80x25 [ 0.001661] console [tty0] enabled [ 0.001667] bootconsole [uart8250] disabled [ 0.001684] kmemleak: Kernel memory leak detector disabled [ 0.001702] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.001715] pid_max: default: 32768 minimum: 301 [ 0.002161] Security Framework initialized [ 0.002385] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.002393] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003511] ftrace: allocating 47146 entries in 185 pages [ 0.178253] sched-energy: CPU device node has no sched-energy-costs [ 0.178288] ASID allocator initialised with 65536 entries [ 0.215826] tegra-id: chipid=22117. [ 0.215840] tegra-id: opt_subrevision=0. [ 0.215858] Tegra Speedo/IDDQ fuse revision 4 [ 0.215864] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.215869] Tegra: CPU Process ID 0, SoC Process ID 0, GPU Process ID 0 [ 0.215875] Tegra: CPU Speedo Value 1998, SoC Speedo Value 1913, GPU Speedo Value 2006 [ 0.215880] Tegra: CPU IDDQ Value 1292, SoC IDDQ Value 1520, GPU IDDQ Value 1755 [ 0.215898] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 0 [ 0.215915] DTS File Name: /home/unisystem/kevmo314_tutorial/Linux_for_Tegra/source/public/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.215923] DTB Build time: Oct 15 2021 13:25:28 [ 0.265068] CPU1: Booted secondary processor [411fd071] [ 0.296981] CPU2: Booted secondary processor [411fd071] [ 0.328950] CPU3: Booted secondary processor [411fd071] [ 0.329034] Brought up 4 CPUs [ 0.329041] SMP: Total of 4 processors activated. [ 0.329050] CPU features: detected feature: 32-bit EL0 Support [ 0.329312] CPU: All CPU(s) started at EL2 [ 0.329330] alternatives: patching kernel code [ 0.337577] devtmpfs: initialized [ 0.375175] Initilizing CustomIPI irq domain [ 0.375559] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.375581] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.386231] pinctrl core: initialized pinctrl subsystem [ 0.386877] OS set in device tree is not L4T. [ 0.387281] regulator-dummy: no parameters [ 0.387566] Initializing plugin-manager [ 0.387686] Plugin module not found [ 0.387917] node /plugin-manager/fragement@0 match with board >=3448-0000-100 [ 0.388497] node /plugin-manager/fragment@1 match with board >=3448-0000-101 [ 0.389796] node /plugin-manager/fragement@7 match with odm-data enable-pmic-wdt [ 0.390065] node /plugin-manager/fragement@8 match with odm-data enable-pmic-wdt [ 0.390751] node /plugin-manager/fragement@10 match with board >=3448-0000-300 [ 0.392819] node /plugin-manager/fragement@11 match with board >=3448-0000-300 [ 0.396120] NET: Registered protocol family 16 [ 0.402509] pstore: using zlib compression [ 0.402544] console [pstore-1] enabled [ 0.402548] pstore: Registered ramoops as persistent store backend [ 0.402554] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.417086] cpuidle: using governor menu [ 0.420276] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.422130] vdso: 2 pages (1 code @ ffffff8008f87000, 1 data @ ffffff8009e84000) [ 0.422156] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.425502] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.428214] tegra_powergate_init: DONE [ 0.428229] DTS File Name: /home/unisystem/kevmo314_tutorial/Linux_for_Tegra/source/public/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.428237] DTB Build time: Oct 15 2021 13:25:28 [ 0.430016] Tegra reboot handler registered. [ 0.434527] iommu: Adding device tegra-carveouts to group 0 [ 0.434666] platform tegra-carveouts: domain=ffffffc0f944e318 allocates as[0]=ffffffc0f9bd40a8 [ 0.435001] iommu: Adding device smmu_test to group 1 [ 0.435045] platform smmu_test: domain=ffffffc0f944e558 allocates as[0]=ffffffc0f9bd4110 [ 0.435844] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.435898] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.435957] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.435969] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.435989] mc-err: mcerr ops are set to t21x [ 0.446110] iommu: Adding device 70090000.xusb to group 2 [ 0.446406] iommu: Adding device 70006000.serial to group 3 [ 0.446465] platform 70006000.serial: domain=ffffffc0f9462c18 allocates as[0]=ffffffc0f9bd4178 [ 0.446868] iommu: Adding device 70006040.serial to group 4 [ 0.447123] iommu: Adding device 70006200.serial to group 5 [ 0.447305] iommu: Adding device sound to group 6 [ 0.447351] platform sound: domain=ffffffc0f94da198 allocates as[0]=ffffffc0f9bd41e0 [ 0.447897] iommu: Adding device 7000d400.spi to group 7 [ 0.448160] iommu: Adding device 7000d600.spi to group 8 [ 0.448461] iommu: Adding device 70410000.spi to group 9 [ 0.448756] iommu: Adding device 50000000.host1x to group 10 [ 0.449035] iommu: Adding device 54080000.vi to group 11 [ 0.449460] iommu: Adding device 54600000.isp to group 12 [ 0.449720] iommu: Adding device 54680000.isp to group 13 [ 0.449996] iommu: Adding device tegradc.0 to group 14 [ 0.450043] platform tegradc.0: domain=ffffffc0f94e60d8 allocates as[0]=ffffffc0f9bd4248 [ 0.451421] platform tegradc.0: IOVA linear map 0x0000000092ca9000(140000) [ 0.451809] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.452130] iommu: Adding device tegradc.1 to group 15 [ 0.452181] platform tegradc.1: domain=ffffffc0f94e6318 allocates as[0]=ffffffc0f9bd42b0 [ 0.453581] platform tegradc.1: IOVA linear map 0x0000000092ca9000(140000) [ 0.453970] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.454250] iommu: Adding device 54340000.vic to group 16 [ 0.454446] iommu: Adding device 544c0000.nvenc to group 17 [ 0.454647] iommu: Adding device 54500000.tsec to group 18 [ 0.454831] iommu: Adding device 54100000.tsecb to group 19 [ 0.455042] iommu: Adding device 54480000.nvdec to group 20 [ 0.455230] iommu: Adding device 54380000.nvjpg to group 21 [ 0.456264] iommu: Adding device 546c0000.i2c to group 22 [ 0.456583] iommu: Adding device 57000000.gpu to group 23 [ 0.456630] platform 57000000.gpu: domain=ffffffc0f9581318 allocates as[0]=ffffffc0f9bd4318 [ 0.456690] platform 57000000.gpu: domain=ffffffc0f9581318 allocates as[1]=ffffffc0f9bd4380 [ 0.456727] platform 57000000.gpu: domain=ffffffc0f9581318 allocates as[2]=ffffffc0f9bd43e8 [ 0.456761] platform 57000000.gpu: domain=ffffffc0f9581318 allocates as[3]=ffffffc0f9bd4450 [ 0.457649] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.457658] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.457671] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET [ 0.457675] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.457679] tegra-pmc: ### PMC reset status reg: 0x3 [ 0.509263] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.509270] tegra-pmc: Clear bootloader IO dpd settings [ 0.509290] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.509358] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.509638] iommu: Adding device 70012000.se to group 24 [ 0.510387] iommu: Adding device 7000c000.i2c to group 25 [ 0.510635] iommu: Adding device 7000c400.i2c to group 26 [ 0.510883] iommu: Adding device 7000c500.i2c to group 27 [ 0.511115] iommu: Adding device 7000c700.i2c to group 28 [ 0.511360] iommu: Adding device 7000d000.i2c to group 29 [ 0.511601] iommu: Adding device 7000d100.i2c to group 30 [ 0.511889] iommu: Adding device sdhci-tegra.0 to group 31 [ 0.511943] platform sdhci-tegra.0: domain=ffffffc0f9590498 allocates as[0]=ffffffc0f9bd44b8 [ 0.512779] iommu: Adding device 700d0000.xudc to group 32 [ 0.515922] vdd-ac-bat: 5000 mV [ 0.516275] vdd-5v0-sys: 5000 mV [ 0.517228] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.517274] vdd-5v0-hdmi: 5000 mV [ 0.517668] vdd-1v8-sys: 1800 mV [ 0.518093] vdd-fan: supplied by vdd-5v0-sys [ 0.518133] vdd-fan: 5000 mV [ 0.518524] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.518556] vdd-usb-vbus: 5000 mV [ 0.519072] vdd-usb-vbus2: 5000 mV [ 0.550129] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.552619] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.554388] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.554409] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.554447] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.554819] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.562624] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.562986] SCSI subsystem initialized [ 0.563215] libata version 3.00 loaded. [ 0.563531] usbcore: registered new interface driver usbfs [ 0.563581] usbcore: registered new interface driver hub [ 0.563645] usbcore: registered new device driver usb [ 0.567624] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.573115] vdd-core: 600 <--> 1162 mV at 1125 mV [ 0.573930] random: fast init done [ 0.574043] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.577011] vdd-ddr-1v1: 1150 mV [ 0.581048] vdd-pre-reg-1v35: 1350 mV [ 0.584999] vdd-1v8: 1800 mV [ 0.589002] avdd-sys-1v2: 1200 mV [ 0.593002] vdd-pex-1v0: 1050 mV [ 0.593613] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.594143] max77620-ldo3: at 3100 mV [ 0.596999] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.597528] max77620-ldo5: at 3100 mV [ 0.601004] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [ 0.604998] avdd-1v05-pll: 1050 mV [ 0.608997] avdd-io-hdmi-dp: 1050 mV [ 0.611416] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.611682] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.611966] max77620 4-003c: max77620 probe successful [ 0.614630] media: Linux media interface: v0.10 [ 0.614723] Linux video capture interface: v2.00 [ 0.615866] pps_core: LinuxPPS API ver. 1 registered [ 0.615871] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.615939] PTP clock support registered [ 0.619738] tegra_fiq_debugger_init: found FIQ source (IRQ 98) [ 0.626122] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.626969] Advanced Linux Sound Architecture Driver Initialized. [ 0.627627] Bluetooth: Core ver 2.22 [ 0.627678] NET: Registered protocol family 31 [ 0.627682] Bluetooth: HCI device and connection manager initialized [ 0.627695] Bluetooth: HCI socket layer initialized [ 0.627702] Bluetooth: L2CAP socket layer initialized [ 0.627750] Bluetooth: SCO socket layer initialized [ 0.629631] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.629647] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.629693] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.629707] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.632865] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.634093] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.634151] vdd-3v3-sys: 3300 mV [ 0.634408] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.636385] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.636848] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.636909] vdd-3v3-sd: 3300 mV [ 0.637749] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.637793] avdd-io-edp-1v05: 1050 mV [ 0.638205] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.638240] vdd-usb-hub-en: 5000 mV [ 0.639621] camchar: rtcpu character device driver loaded [ 0.640391] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [ 0.641767] clocksource: Switched to clocksource arch_sys_counter [ 0.681914] VFS: Disk quotas dquot_6.6.0 [ 0.682046] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.682541] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.682943] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.682959] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.683148] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.683152] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.683164] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.683190] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.683197] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.683211] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.683220] nvmap_page_pool_init: Total RAM pages: 1010594 [ 0.683224] nvmap_page_pool_init: nvmap page pool size: 126324 pages (493 MB) [ 0.683309] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.683766] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.684691] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.692995] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.693405] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.693664] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.693922] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.694114] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.694374] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.694379] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.694814] NET: Registered protocol family 2 [ 0.695788] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.696001] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.696489] TCP: Hash tables configured (established 32768 bind 32768) [ 0.696632] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.696712] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.697125] NET: Registered protocol family 1 [ 0.698069] RPC: Registered named UNIX socket transport module. [ 0.698075] RPC: Registered udp transport module. [ 0.698079] RPC: Registered tcp transport module. [ 0.698083] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.698100] PCI: CLS 0 bytes, default 64 [ 0.698333] Trying to unpack rootfs image as initramfs... [ 0.994013] Freeing initrd memory: 6992K [ 1.003814] host1x 50000000.host1x: initialized [ 1.005708] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.008902] audit: initializing netlink subsys (disabled) [ 1.008988] audit: type=2000 audit(0.851:1): initialized [ 1.009848] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.019886] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.021349] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.022167] 9p: Installing v9fs 9p2000 file system support [ 1.025339] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 1.025471] io scheduler noop registered [ 1.025798] io scheduler cfq registered (default) [ 1.028448] gic 702f9000.agic: GIC IRQ controller registered [ 1.031736] iommu: Adding device 702ef000.adsp to group 33 [ 1.040559] iommu: Adding device aconnect@702c0000:adsp_audio to group 34 [ 1.040709] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 1.041282] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x71e840f [ 1.041290] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 1.043036] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 1.043143] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 1.043244] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 1.043427] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 1.043517] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 1.043603] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 1.043692] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 1.043779] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 1.043873] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 1.043957] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 1.049876] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 1.051604] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 1.053457] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.054729] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 1.055073] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.056221] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.056445] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 1.056680] Adding domain tsec-pd to PM domain host1x-pd [ 1.058895] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 1.059806] tsec 54500000.tsec: initialized [ 1.061386] tsec 54100000.tsecb: initialized [ 1.062095] Adding domain nvdec-pd to PM domain host1x-pd [ 1.065566] nvdec 54480000.nvdec: initialized [ 1.066646] Adding domain vic03-pd to PM domain host1x-pd [ 1.066830] Adding domain msenc-pd to PM domain host1x-pd [ 1.066988] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.070848] falcon 54340000.vic: initialized [ 1.072110] falcon 544c0000.nvenc: initialized [ 1.073424] falcon 54380000.nvjpg: initialized [ 1.077472] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97 [ 1.077516] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.077549] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.077737] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.077857] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.077863] tegra_cec 70015000.tegra_cec: probed [ 1.077904] display board info: id 0x0, fab 0x0 [ 1.077974] generic_infoframe_type: 0x87 [ 1.078115] tegradc tegradc.0: DT parsed successfully [ 1.078163] tegradc tegradc.0: Display dc.ffffff800ab80000 registered with id=0 [ 1.078641] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 640x480 (on 0x0mm) pclk=25173906 [ 1.085484] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.086802] tegradc tegradc.0: probed [ 1.091998] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.093391] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.093858] kfuse 7000fc00.kfuse: initialized [ 1.095324] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.096434] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.097847] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.097863] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.098351] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.099849] vdd-gpu: applied init 1000000uV constraint [ 1.099862] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.100272] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.104783] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.104933] No Device Node present for smmu client: serial8250 !! [ 1.104948] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.105016] iommu: Adding device serial8250 to group 35 [ 1.108468] console [ttyS0] disabled [ 1.108546] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.108631] console [ttyS0] enabled [ 1.109487] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 1.109835] serial-tegra 70006200.serial: RX in PIO mode [ 1.109928] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 1.110858] [drm] Initialized [ 1.113476] Console: switching to colour frame buffer device 80x30 [ 1.113520] tegradc tegradc.0: fb registered [ 1.121272] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [ 1.121326] tegradc tegradc.0: hdmi: tmds rate:25174K prod-setting:prod_c_hdmi_0m_54m [ 1.121888] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [ 1.121897] brd: module loaded [ 1.121901] tegradc tegradc.0: hdmi: BL set VIC 0 [ 1.121907] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [ 1.127775] loop: module loaded [ 1.127881] tegra_profiler: version: 1.139, samples/io: 47/27 [ 1.128003] tegra_profiler: auth: init [ 1.129279] THERMAL EST: found 2 subdevs [ 1.129290] THERMAL EST num_resources: 0 [ 1.129296] [THERMAL EST subdev 0] [ 1.129304] [THERMAL EST subdev 1] [ 1.129902] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 1.129906] THERMAL EST: thz register success. [ 1.130063] THERMAL EST: end of probe, return err: 0 [ 1.131294] hisi_sas: driver version v1.6 [ 1.135466] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 1.135474] Extcon AUX1(HDMI) enable [ 1.135688] tegra-qspi 70410000.spi: Prod settings list not found [ 1.136451] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 1.136526] tegradc tegradc.1: No lt-data, using default setting [ 1.136554] tegradc tegradc.1: No hpd-gpio in DT [ 1.136587] tegradc tegradc.1: DT parsed successfully [ 1.136634] tegradc tegradc.1: Display dc.ffffff800d500000 registered with id=1 [ 1.137681] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes) [ 1.137691] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0 [ 1.138171] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.144476] libphy: Fixed MDIO Bus: probed [ 1.145226] tun: Universal TUN/TAP device driver, 1.6 [ 1.145231] tun: (C) 1999-2004 Max Krasnyansky [ 1.150219] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.150225] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.150275] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.150279] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.150330] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.150333] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.150375] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 1.150380] Copyright(c) 1999 - 2017 Intel Corporation. [ 1.151348] PPP generic driver version 2.4.2 [ 1.154216] PPP BSD Compression module registered [ 1.154223] PPP Deflate Compression module registered [ 1.154266] PPP MPPE Compression module registered [ 1.154275] NET: Registered protocol family 24 [ 1.154360] usbcore: registered new interface driver r8152 [ 1.154412] usbcore: registered new interface driver asix [ 1.154469] usbcore: registered new interface driver ax88179_178a [ 1.154519] usbcore: registered new interface driver cdc_ether [ 1.154563] usbcore: registered new interface driver net1080 [ 1.154602] usbcore: registered new interface driver cdc_subset [ 1.154634] usbcore: registered new interface driver zaurus [ 1.154693] usbcore: registered new interface driver cdc_ncm [ 1.154905] VFIO - User Level meta-driver version: 0.3 [ 1.156079] tegradc tegradc.1: probed [ 1.156431] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.156455] ehci-pci: EHCI PCI platform driver [ 1.156495] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.156507] ohci-pci: OHCI PCI platform driver [ 1.156546] ohci-platform: OHCI generic platform driver [ 1.159271] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 1.160017] tegradc tegradc.1: fb registered [ 1.164048] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 1.164055] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 1.164068] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 1.164082] tegradc tegradc.1: blank - powerdown [ 1.164104] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 1.164109] Extcon DP: HPD disabled [ 1.164114] hpd: hpd_switch 0 [ 1.164119] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 1.164129] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 1.164137] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 1.164488] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 1.165735] tegra-xusb 70090000.xusb: extcon 0: ffffffc0fa5d2c00 id [ 1.166937] usbcore: registered new interface driver uas [ 1.166995] usbcore: registered new interface driver usb-storage [ 1.167100] usbcore: registered new interface driver usbserial [ 1.172852] tegra-xudc-new 700d0000.xudc: device count: 1 [ 1.173097] tegra-xusb 70090000.xusb: Firmware timestamp: 2020-07-31 09:33:12 UTC, Version: 50.26 release [ 1.173151] tegra-xusb 70090000.xusb: xHCI Host Controller [ 1.173191] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 1.174010] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 1.174072] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 1.174295] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.174302] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.174307] usb usb1: Product: xHCI Host Controller [ 1.174313] usb usb1: Manufacturer: Linux 4.9.140-tegra-tegra xhci-hcd [ 1.174317] usb usb1: SerialNumber: 70090000.xusb [ 1.174484] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 1.174500] tegra-xudc-new 700d0000.xudc: vbus state: 0 [ 1.174981] hub 1-0:1.0: USB hub found [ 1.175029] hub 1-0:1.0: 5 ports detected [ 1.175072] tegra-xudc-new 700d0000.xudc: entering ELPG [ 1.175394] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 1.175761] tegra-xusb 70090000.xusb: xHCI Host Controller [ 1.175776] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 1.175895] mousedev: PS/2 mouse device common for all mice [ 1.175907] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.176015] usbcore: registered new interface driver xpad [ 1.176083] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.176090] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.176095] usb usb2: Product: xHCI Host Controller [ 1.176101] usb usb2: Manufacturer: Linux 4.9.140-tegra-tegra xhci-hcd [ 1.176105] usb usb2: SerialNumber: 70090000.xusb [ 1.176225] [ILITEK][MSG][ilitek_main_probe:1912] ILITEK client->addr = 0x41 client->irq = 0 [ 1.176233] [ILITEK][MSG][ilitek_main_probe:1925] ilitek log level: 3 [ 1.176299] [ILITEK][ERR][ilitek_request_regulator:1868] regulator_get vdd fail [ 1.176317] [ILITEK][ERR][ilitek_request_regulator:1879] regulator_get vdd_i2c fail [ 1.176324] [ILITEK][MSG][ilitek_power_on:1800] POWER ON [ 1.176342] OF: /i2c@7000c000/ilitek@41: could not get #gpio-cells for /pinmux@700008d4 [ 1.176422] tegradc tegradc.0: nominal-pclk:25174825 parent:25173906 div:1.0 pclk:25173906 24923052~27440532 [ 1.176647] hub 2-0:1.0: USB hub found [ 1.176685] hub 2-0:1.0: 4 ports detected [ 1.184540] [ILITEK][ERR][ilitek_get_gpio_num:1557] reset_gpio = -22 [ 1.184561] OF: /i2c@7000c000/ilitek@41: could not get #gpio-cells for /pinmux@700008d4 [ 1.192589] [ILITEK][ERR][ilitek_get_gpio_num:1560] irq_gpio = -22 [ 1.192593] [ILITEK][MSG][ilitek_get_gpio_num:1567] reset_gpio = -22 irq_gpio = -22 [ 1.192599] [ILITEK][MSG][ilitek_reset:454] delay: 1000 [ 1.192602] [ILITEK][ERR][ilitek_reset:494] reset pin is invalid [ 1.192608] [ILITEK][MSG][api_init_func:645] [ 1.253742] tegradc tegradc.0: blank - powerdown [ 1.277840] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 1.296463] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 1.296466] Extcon AUX1(HDMI) disable [ 1.339099] tegradc tegradc.0: unblank [ 1.381212] tegradc tegradc.0: nominal-pclk:148500000 parent:148500000 div:1.0 pclk:148500000 147015000~161865000 [ 1.381290] tegradc tegradc.0: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_75m_150m [ 1.398216] [ILITEK][MSG][api_ptl_get_ptl_ver:164] protocol version: 3.1.0 ts->ptl.ver = 0x30100 [ 1.401744] tegradc tegradc.0: sync windows ret = 250 [ 1.413120] extcon-disp-state extcon:disp-state: cable 51 state 1 [ 1.413124] Extcon HDMI: HPD enabled [ 1.413154] tegradc tegradc.0: hdmi: plugged [ 1.484027] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.501785] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 1.530980] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411 [ 1.530986] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.530992] usb 1-2: Product: 4-Port USB 2.1 Hub [ 1.530997] usb 1-2: Manufacturer: Generic [ 1.532257] hub 1-2:1.0: USB hub found [ 1.532855] hub 1-2:1.0: 4 ports detected [ 1.598406] [ILITEK][MSG][api_init_func:665] Protocol: V3, set ISR falling trigger [ 1.598415] [ILITEK][MSG][ilitek_read_tp_info:1733] driver version 5.9.0.4.0.0.0 [ 1.613781] [ILITEK][MSG][api_ptl_get_ptl_ver:164] protocol version: 3.1.0 ts->ptl.ver = 0x30100 [ 1.619793] [ILITEK][MSG][api_ptl_get_mcu_ver:114] MCU KERNEL version:0x2511 [ 1.619797] [ILITEK][MSG][api_ptl_get_mcu_ver:115] Module name:ILI2511001215A00 [ 1.625173] [ILITEK][MSG][api_ptl_get_fw_ver:146] firmware version:0x6.0x0.0x0.0x0.0x63.0x66.0x0.0x1 [ 1.630545] [ILITEK][MSG][api_ptl_get_sc_res:184] screen_min_x: 0, screen_min_y: 0 screen_max_x: 16383, screen_max_y: 16383 [ 1.635973] [ILITEK][MSG][api_ptl_get_tp_res_v3:284] tp_min_x: 0, tp_max_x: 16384, tp_min_y: 0, tp_max_y: 16384, ch_x: 35, ch_y: 20, max_tp: 10, key_count: 0 [ 1.641225] [ILITEK][MSG][api_ptl_check_mode:127] ilitek ic. mode =90 , it's AP MODE [ 1.651562] input: ilitek_ts as /devices/7000c000.i2c/i2c-0/0-0041/input/input0 [ 1.651894] invalid GPIO -22 [ 1.651973] ------------[ cut here ]------------ [ 1.652005] WARNING: CPU: 2 PID: 1 at /home/unisystem/kevmo314_tutorial/Linux_for_Tegra/source/public/kernel/kernel-4.9/drivers/gpio/gpiolib.c:106 gpio_to_desc+0xd8/0xe0 [ 1.652008] Modules linked in: [ 1.652028] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.9.140-tegra-tegra #6 [ 1.652032] Hardware name: NVIDIA Jetson Nano Developer Kit (DT) [ 1.652036] task: ffffffc0fa6f0000 task.stack: ffffffc0fa66c000 [ 1.652042] PC is at gpio_to_desc+0xd8/0xe0 [ 1.652047] LR is at gpio_to_desc+0xd8/0xe0 [ 1.652052] pc : [] lr : [] pstate: 40400045 [ 1.652055] sp : ffffffc0fa66fb60 [ 1.652058] x29: ffffffc0fa66fb60 x28: ffffff8009844358 [ 1.652067] x27: ffffff8009688e08 x26: ffffff800960a1a0 [ 1.652075] x25: ffffff800a160000 x24: ffffff8009620490 [ 1.652083] x23: ffffffc0f7bc0000 x22: ffffff8009072000 [ 1.652090] x21: ffffff800a1af000 x20: 00000000ffffffea [ 1.652097] x19: 0000000000000000 x18: 0000000000000001 [ 1.652104] x17: 0000000000000001 x16: 0000000000000000 [ 1.652110] x15: ffffffffffffffff x14: ffffff800a168260 [ 1.652117] x13: 0000000000000000 x12: 0000000000000004 [ 1.652123] x11: 0000000000000002 x10: 000000000000021a [ 1.652130] x9 : 0000000000000001 x8 : ffffffc0fef9c208 [ 1.652137] x7 : 0000000000000000 x6 : 000000000d71d7ef [ 1.652143] x5 : 0000000000000000 x4 : 0000000000000000 [ 1.652150] x3 : ffffffffffffffff x2 : ffffff8009ea42c8 [ 1.652156] x1 : ffffffc0fa6f0000 x0 : 0000000000000010 [ 1.652172] ---[ end trace 3a24d4afd6c4d4f3 ]--- [ 1.652176] Call trace: [ 1.652184] [] gpio_to_desc+0xd8/0xe0 [ 1.652200] [] ilitek_main_probe+0x4d8/0xa88 [ 1.652207] [] ilitek_touch_driver_probe+0x28/0x40 [ 1.652220] [] i2c_device_probe+0x144/0x258 [ 1.652231] [] driver_probe_device+0xd8/0x408 [ 1.652236] [] __driver_attach+0xdc/0x128 [ 1.652246] [] bus_for_each_dev+0x5c/0xa8 [ 1.652250] [] driver_attach+0x30/0x40 [ 1.652254] [] bus_add_driver+0x20c/0x2a8 [ 1.652259] [] driver_register+0x6c/0x110 [ 1.652265] [] i2c_register_driver+0x4c/0xb0 [ 1.652280] [] ilitek_touch_driver_init+0x20/0xa8 [ 1.652291] [] do_one_initcall+0x44/0x130 [ 1.652303] [] kernel_init_freeable+0x1a0/0x244 [ 1.652315] [] kernel_init+0x18/0x108 [ 1.652320] [] ret_from_fork+0x10/0x40 [ 1.652357] [ILITEK][MSG][ilitek_request_irq:1324] ts->client->irq: -22 [ 1.652362] [ILITEK][ERR][ilitek_main_probe:1960] ilitek_request_irq failed, err: -22 [ 1.652369] [ILITEK][MSG][ilitek_power_on:1800] POWER OFF [ 1.652372] [ILITEK][ERR][ilitek_main_probe:1991] return -ENODEV [ 1.652511] [ILITEK][MSG][ilitek_touch_driver_init:333] add touch device driver i2c driver. [ 1.784137] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 1.786760] rtc rtc1: alarm rtc device [ 1.786786] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.786818] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.787621] i2c /dev entries driver [ 1.789812] i2c i2c-6: Added multiplexed i2c bus 7 [ 1.790219] i2c i2c-6: Added multiplexed i2c bus 8 [ 1.790226] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 1.790977] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [ 1.814320] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 1.814412] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.822061] imx219 7-0010: board setup failed [ 1.826598] imx219: probe of 7-0010 failed with error -121 [ 1.827198] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [ 1.850490] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 1.850580] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.858174] imx219 8-0010: board setup failed [ 1.862651] imx219: probe of 8-0010 failed with error -121 [ 1.863839] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 1.866690] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 1.866698] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 1.867166] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.867185] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 1.867196] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 1.867360] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.867372] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 1.867380] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 1.867528] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.867540] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 1.867546] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 1.867721] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 1.868557] tegra_aotag tegra-aotag: Registering sensor 0 [ 1.868610] tegra_aotag tegra-aotag: Invalid temp readout [ 1.868634] tegra_aotag tegra-aotag: Invalid temp readout [ 1.868652] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 1.868661] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 1.869708] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.869730] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 1.869975] tegra_aotag tegra-aotag: Invalid temp readout [ 1.870007] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 1.870488] parse_throttle_dt_data: Num cap clks = 6 [ 1.870496] parse_throttle_dt_data: clk=cclk_g type=2 [ 1.870511] parse_throttle_dt_data: clk=gpu type=4 [ 1.870538] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 1.870558] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 1.870580] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 1.870585] parse_throttle_dt_data: clk=emc type=3 [ 1.871040] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.871147] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.871346] tegra_throttle_probe: probe successful. #cdevs=4 [ 1.872167] FAN dev name: pwm-fan [ 1.872259] FAN:gpio request success. [ 1.872343] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 1.872655] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 1.872825] pwm_fan_driver pwm-fan: fan tach request irq success [ 1.872835] pwm_fan_driver pwm-fan: tach period: 1000 [ 1.872932] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 1.872938] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 1.872943] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 1.872948] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 1.872953] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 1.872958] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 1.872963] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 1.872967] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 1.872972] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 1.872977] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 1.875197] device-mapper: uevent: version 1.0.3 [ 1.875692] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 1.880425] tegra210-cpufreq cpufreq: probe()...completed [ 1.881550] sdhci: Secure Digital Host Controller Interface driver [ 1.881554] sdhci: Copyright(c) Pierre Ossman [ 1.881559] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.882422] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 1.882912] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 1.883157] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300 [ 1.887939] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.889833] tegra-se 70012000.se: tegra_se_probe: complete [ 1.890585] hidraw: raw HID events driver (C) Jiri Kosina [ 1.892399] usbcore: registered new interface driver usbhid [ 1.892406] usbhid: USB HID core driver [ 1.895604] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 1.896054] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 1.899016] nvpmodel: initialized successfully [ 1.901027] usbcore: registered new interface driver snd-usb-audio [ 1.901143] No Device Node present for smmu client: snd-soc-dummy !! [ 1.901152] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.901196] iommu: Adding device snd-soc-dummy to group 36 [ 1.907390] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input1 [ 1.933281] OPE platform probe [ 1.933424] OPE platform probe successful [ 1.933813] OPE platform probe [ 1.933959] OPE platform probe successful [ 1.934153] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 1.967759] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 1.967984] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 1.968174] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 1.968384] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 1.968567] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 1.968763] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 1.968955] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 1.969142] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 1.969323] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 1.969516] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 1.989033] u32 classifier [ 1.989040] Actions configured [ 1.989208] Initializing XFRM netlink socket [ 1.990302] NET: Registered protocol family 10 [ 1.991504] NET: Registered protocol family 17 [ 1.991527] NET: Registered protocol family 15 [ 1.991626] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.991719] Bluetooth: RFCOMM socket layer initialized [ 1.991742] Bluetooth: RFCOMM ver 1.11 [ 1.991757] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.991764] Bluetooth: HIDP socket layer initialized [ 1.991789] 9pnet: Installing 9P2000 support [ 1.991861] Key type dns_resolver registered [ 1.992420] Registered cp15_barrier emulation handler [ 1.992431] Registered setend emulation handler [ 1.994044] registered taskstats version 1 [ 1.995189] Adding domain ve2-pd to PM domain host1x-pd [ 1.995536] Adding domain ve-pd to PM domain host1x-pd [ 1.999969] isp 54600000.isp: initialized [ 2.001347] isp 54680000.isp: initialized [ 2.022087] last reset is due to software reset [ 2.022100] KERNEL: PMC reset status reg: 0x3 [ 2.022380] BL: PMC reset status reg: 0x3 [ 2.022383] BL: PMIC poweroff Event Recorder: 0x0 [ 2.026693] clk_cbus_recalc_rate: no gbus parent [ 2.026709] clk_cbus_round_rate: no gbus parent [ 2.026712] clk_cbus_round_rate: no gbus parent [ 2.026735] clk_cbus_recalc_rate: no gbus parent [ 2.026963] clk_cbus_recalc_rate: no gbus parent [ 2.026967] clk_cbus_round_rate: no gbus parent [ 2.026971] clk_cbus_round_rate: no gbus parent [ 2.026976] clk_cbus_recalc_rate: no gbus parent [ 2.027700] tegra_dvfs: GPU-cap: registered [ 2.027841] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 2.027844] tegra dvfs: vdd-core: nominal 1125mV, offset 600000uV, step 12500uV, scaling enabled [ 2.027847] tegra dvfs: vdd-gpu: nominal 1078mV, offset 708000uV, step 10000uV, scaling enabled [ 2.030211] tegra_dvfs: vdd-gpu-vts: registered [ 2.031507] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 2.032535] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 2.033744] input: gpio-keys as /devices/gpio-keys/input/input2 [ 2.067691] tegra_rtc 7000e000.rtc: setting system clock to 2021-10-15 11:27:16 UTC (1634297236) [ 2.070514] vi 54080000.vi: vi_probe: ++ [ 2.075648] vi 54080000.vi: initialized [ 2.078117] vi 54080000.vi: subdev nvcsi--2 bound [ 2.078250] vi 54080000.vi: subdev nvcsi--1 bound [ 2.079701] Disable partitions left on by BL [ 2.079709] disb [ 2.079795] bwmgr: missing cdev-type property [ 2.079985] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 2.079997] DRAM derating cdev registered. [ 2.082352] vdd-fan: disabling [ 2.082360] vdd-usb-vbus: disabling [ 2.082364] vdd-usb-vbus2: disabling [ 2.082387] vddio-sdmmc3-ap: disabling [ 2.082692] avdd-io-edp-1v05: disabling [ 2.082698] vdd-usb-hub-en: disabling [ 2.082794] ALSA device list: [ 2.082799] #0: tegra-hda at 0x70038000 irq 83 [ 2.082802] #1: tegra-snd-t210ref-mobile-rt565x [ 2.091749] Freeing unused kernel memory: 8576K [ 2.106183] tegra_cec 70015000.tegra_cec: physical address: 00:00. [ 2.134971] Root device found: mmcblk0p1 [ 2.138154] mmc0: hw tuning done ... [ 2.138248] mmc0: new ultra high speed SDR104 SDXC card at address 59b4 [ 2.139102] mmcblk0: mmc0:59b4 59.5 GiB [ 2.143078] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 [ 2.170929] tegra_cec 70015000.tegra_cec: Sent res: -113. [ 2.170939] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 2.300818] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.302961] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.343592] Found dev node: /dev/mmcblk0p1 [ 2.385733] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 2.389850] Rootfs mounted over mmcblk0p1 [ 2.407931] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.407953] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.407959] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.407964] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.407970] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.408031] pci 0000:00:02.0: [10de:0faf] type 01 class 0x060400 [ 2.408156] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.408430] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.408585] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 2.408610] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.408640] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 2.408661] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit] [ 2.408810] pci 0000:01:00.0: supports D1 D2 [ 2.408813] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.417924] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.417986] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [ 2.417991] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.418001] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit] [ 2.418020] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit] [ 2.418036] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.418045] pci 0000:00:02.0: PCI bridge to [bus 01] [ 2.418051] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.418057] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] [ 2.418605] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 2.418611] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.418616] pcie_pme 0000:00:02.0:pcie001: service driver pcie_pme loaded [ 2.418722] aer 0000:00:02.0:pcie002: service driver aer loaded [ 2.419026] r8168 0000:01:00.0: enabling device (0000 -> 0003) [ 2.419053] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 2.426634] Switching from initrd to actual rootfs [ 2.434107] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 2.434506] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:ec:30:b5 from device tree [ 2.435678] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 2.435736] r8168 Copyright (C) 2017 Realtek NIC software team This program comes with ABSOLUTELY NO WARRANTY; for details, please see . This is free software, and you are welcome to redistribute it under certain conditions; see . [ 2.513946] usb 1-2.3: new full-speed USB device number 4 using tegra-xusb [ 2.538463] usb 1-2.3: New USB device found, idVendor=046d, idProduct=c52b [ 2.538470] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.538474] usb 1-2.3: Product: USB Receiver [ 2.538477] usb 1-2.3: Manufacturer: Logitech [ 2.656706] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.670280] cgroup: cgroup2: unknown option "nsdelegate" [ 2.681041] pstore: decompression failed;returned -5 [ 2.688924] pstore: decompression failed;returned -5 [ 2.711018] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 2.712153] systemd[1]: Detected architecture arm64. [ 2.741371] systemd[1]: Set hostname to . [ 2.865698] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 2.865714] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 3.001615] random: systemd: uninitialized urandom read (16 bytes read) [ 3.004369] systemd[1]: Created slice User and Session Slice. [ 3.004709] random: systemd: uninitialized urandom read (16 bytes read) [ 3.004880] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 3.004990] random: systemd: uninitialized urandom read (16 bytes read) [ 3.006289] systemd[1]: Created slice System Slice. [ 3.007020] systemd[1]: Listening on Journal Audit Socket. [ 3.007330] systemd[1]: Listening on Journal Socket (/dev/log). [ 3.113041] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 3.471734] systemd-journald[1983]: Received request to flush runtime journal from PID 1 [ 4.628190] random: crng init done [ 4.628206] random: 7 urandom warning(s) missed due to ratelimiting [ 4.688247] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [ 5.338398] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 5.338414] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 5.474750] using random self ethernet address [ 5.479846] using random host ethernet address [ 5.662401] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 5.695844] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411 [ 5.695874] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.695878] usb 2-1: Product: 4-Port USB 3.1 Hub [ 5.695882] usb 2-1: Manufacturer: Generic [ 5.700932] hub 2-1:1.0: USB hub found [ 5.701843] hub 2-1:1.0: 4 ports detected [ 5.990290] usb 2-1.1: new SuperSpeed USB device number 3 using tegra-xusb [ 6.021976] usb 2-1.1: New USB device found, idVendor=13fe, idProduct=5500 [ 6.021988] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 6.021994] usb 2-1.1: Product: Silicon-Power16G [ 6.021998] usb 2-1.1: Manufacturer: UFD 3.0 [ 6.022002] usb 2-1.1: SerialNumber: P180058507088395041C2801 [ 6.023831] usb-storage 2-1.1:1.0: USB Mass Storage device detected [ 6.032217] scsi host0: usb-storage 2-1.1:1.0 [ 6.793512] Mass Storage Function, version: 2009/09/11 [ 6.793531] LUN: removable file: (no medium) [ 6.813645] using random self ethernet address [ 6.827607] using random host ethernet address [ 7.359802] scsi 0:0:0:0: Direct-Access UFD 3.0 Silicon-Power16G PMAP PQ: 0 ANSI: 6 [ 7.360714] rndis0: HOST MAC 72:d3:64:40:24:18 [ 7.360880] rndis0: MAC 72:d3:64:40:24:19 [ 7.367638] usb0: HOST MAC 72:d3:64:40:24:1a [ 7.367706] usb0: MAC 72:d3:64:40:24:1b [ 7.367769] tegra-xudc-new 700d0000.xudc: exiting ELPG [ 7.374981] sd 0:0:0:0: [sda] 30965760 512-byte logical blocks: (15.9 GB/14.8 GiB) [ 7.375794] tegra-xudc-new 700d0000.xudc: exiting ELPG done [ 7.375837] tegra-xudc-new 700d0000.xudc: ep 0 (type: 0, dir: out) enabled [ 7.375893] tegra-xudc-new 700d0000.xudc: entering ELPG [ 7.376185] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 7.376303] tegra-xudc-new 700d0000.xudc: exiting ELPG [ 7.376985] tegra-xudc-new 700d0000.xudc: exiting ELPG done [ 7.377013] tegra-xudc-new 700d0000.xudc: entering ELPG [ 7.377270] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 7.384539] sd 0:0:0:0: [sda] Write Protect is off [ 7.389554] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00 [ 7.390338] l4tbr0: port 1(rndis0) entered blocking state [ 7.390347] l4tbr0: port 1(rndis0) entered disabled state [ 7.390806] sd 0:0:0:0: [sda] No Caching mode page found [ 7.391889] device rndis0 entered promiscuous mode [ 7.396539] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 7.414720] IPv6: ADDRCONF(NETDEV_UP): rndis0: link is not ready [ 7.469310] l4tbr0: port 2(usb0) entered blocking state [ 7.469326] l4tbr0: port 2(usb0) entered disabled state [ 7.478092] device usb0 entered promiscuous mode [ 7.502748] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 7.690362] sda: sda1 [ 7.695283] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 7.835871] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 7.840213] eth0: 0xffffff800ab6d000, 00:04:4b:ec:30:b5, IRQ 407 [ 7.864538] logitech-djreceiver 0003:046D:C52B.0003: hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-70090000.xusb-2.3/input2 [ 7.907563] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 8.416378] zram: Added device: zram0 [ 8.423346] zram: Added device: zram1 [ 8.426416] zram: Added device: zram2 [ 8.430844] zram: Added device: zram3 [ 8.525590] zram0: detected capacity change from 0 to 519417856 [ 9.058048] Adding 507240k swap on /dev/zram0. Priority:5 extents:1 across:507240k SS [ 9.075013] zram1: detected capacity change from 0 to 519417856 [ 9.119944] Adding 507240k swap on /dev/zram1. Priority:5 extents:1 across:507240k SS [ 9.137511] zram2: detected capacity change from 0 to 519417856 [ 9.201350] Adding 507240k swap on /dev/zram2. Priority:5 extents:1 across:507240k SS [ 9.220876] zram3: detected capacity change from 0 to 519417856 [ 9.287507] Adding 507240k swap on /dev/zram3. Priority:5 extents:1 across:507240k SS [ 10.388534] Bridge firewalling registered [ 10.542080] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 10.875689] input: Logitech M310/M310t as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.2/0003:046D:C52B.0003/0003:046D:4031.0004/input/input3 [ 10.876739] logitech-hidpp-device 0003:046D:4031.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech M310/M310t] on usb-70090000.xusb-2.3:1 [ 10.924796] input: Logitech K520 as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.2/0003:046D:C52B.0003/0003:046D:2011.0005/input/input4 [ 10.929473] logitech-hidpp-device 0003:046D:2011.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech K520] on usb-70090000.xusb-2.3:2 [ 11.823852] tegradc tegradc.0: unblank [ 11.823891] tegradc tegradc.1: blank - powerdown [ 11.994301] r8168: eth0: link up [ 11.994431] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 12.226132] Netfilter messages via NETLINK v0.30. [ 12.245216] ctnetlink v0.93: registering with nfnetlink. [ 13.219856] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready [ 14.616640] fuse init (API version 7.26) [ 18.430050] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 18.430088] Bluetooth: BNEP socket layer initialized [ 20.413169] tegradc tegradc.0: unblank [ 20.413202] tegradc tegradc.1: blank - powerdown