[0000.203] [L4T TegraBoot] (version 00.00.2018.01-l4t-39a9dc3d) [0000.209] Processing in cold boot mode Bootloader 2 [0000.213] A02 Bootrom Patch rev = 1023 [0000.217] Power-up reason: software reset [0000.221] No Battery Present [0000.223] pmic max77620 reset reason [0000.227] pmic max77620 NVERC : 0x0 [0000.230] RamCode = 0 [0000.232] Platform has DDR4 type RAM [0000.236] max77620 disabling SD1 Remote Sense [0000.240] Setting DDR voltage to 1125mv [0000.244] Serial Number of Pmic Max77663: 0xf03f1 [0000.251] Entering ramdump check [0000.254] Get RamDumpCarveOut = 0x0 [0000.257] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.263] Last reboot was clean, booting normally! [0000.267] Sdram initialization is successful [0000.271] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.277] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.283] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.289] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.295] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.301] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.307] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.312] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.329] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.335] Platform-DebugCarveout: 0 [0000.338] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.344] Non secure mode, and RB not enabled. [0000.360] Csd NumOfBlocks=0 [0000.554] *** Booting BFS0. [0000.560] Using BFS PT to query partitions [0001.492] *** Booting KFS0. [0001.495] Using GPT Primary to query partitions [0001.500] Loading Tboot-CPU binary [0001.507] Verifying TBC in OdmNonSecureSBK mode [0001.517] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0001.524] Bootloader downloaded successfully. [0001.528] Downloaded Tboot-CPU binary to 0xa0000258 [0001.533] MAX77620_GPIO5 configured [0001.536] CPU power rail is up [0001.539] CPU clock enabled [0001.543] Performing RAM repair [0001.546] Updating A64 Warmreset Address to 0xa00002e9 [0001.551] Loading NvTbootBootloaderDTB [0001.568] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0001.634] Bootloader DTB Load Address: 0x83000000 [0001.638] Loading NvTbootKernelDTB [0001.667] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0001.732] Kernel DTB Load Address: 0x83100000 [0001.737] Loading cboot binary [0001.748] Verifying EBT in OdmNonSecureSBK mode [0001.790] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0001.797] Bootloader downloaded successfully. [0001.801] Next binary entry address: 0x92c00258 [0001.806] BoardId: 3448 [0001.810] Overriding pmu board id with proc board id [0001.815] Display board id is not available [0001.827] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.879] /bpmp deleted [0001.881] SC7EntryFw header found loaded at 0xff700000 [0002.071] OVR2 PMIC [0002.073] Bpmp FW successfully loaded [0002.078] WB0 init successfully at 0xff780000 [0002.082] Set NvDecSticky Bits [0002.085] GSC2 address ff53fffc value c0edbbcc [0002.092] GSC MC Settings done [0002.095] TOS Image length 53680 [0002.098] Monitor size 53680 [0002.101] OS size 0 [0002.107] Secure Os AES-CMAC Verification Success! [0002.111] TOS image cipher info: plaintext [0002.115] Loading and Validation of Secure OS Successful [0002.131] SC7 Entry Firmware - 0xff700000, 0x4000 [0002.135] NvTbootPackSdramParams: start. [0002.141] NvTbootPackSdramParams: done. [0002.144] Tegraboot started after 132246 us [0002.148] Basic modules init took 1731533 us [0002.152] Sec Bootdevice Read Time = 912 ms, Read Size = 14457 KB [0002.158] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0002.164] Next stage binary read took 7387 us [0002.168] Carveout took -19261 us [0002.171] CPU initialization took 344305 us [0002.175] Total time taken by TegraBoot 2063964 us [0002.180] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):23b153a63 NOTICE: BL31: Built : 22:39:57, Dec 9 2019 ERROR: Error initializing runtime service trusty_fast [0002.302] RamCode = 0 [0002.307] LPDDR4 Training: Read DT: Number of tables = 2 [0002.312] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0002.325] EMC Training Successful [0002.328] 408000 not found in DVFS table [0002.334] RamCode = 0 [0002.337] DT Write: emc-table@204000 succeeded [0002.343] DT Write: emc-table@1600000 succeeded [0002.347] LPDDR4 Training: Write DT: Number of tables = 2 [0002.413] [0002.414] Debug Init done [0002.417] Marked DTB cacheable [0002.419] Bootloader DTB loaded at 0x83000000 [0002.424] Marked DTB cacheable [0002.427] Kernel DTB loaded at 0x83100000 [0002.431] DeviceTree Init done [0002.447] Pinmux applied successfully [0002.451] gicd_base: 0x50041000 [0002.455] gicc_base: 0x50042000 [0002.458] Interrupts Init done [0002.462] Using base:0x60005090 & irq:208 for tick-timer [0002.467] Using base:0x60005098 for delay-timer [0002.471] platform_init_timer: DONE [0002.475] Timer(tick) Init done [0002.479] osc freq = 38400 khz [0002.483] [0002.484] Welcome to L4T Cboot [0002.487] [0002.488] Cboot Version: 00.00.2018.01-t210-40c3ff9c [0002.493] calling constructors [0002.496] initializing heap [0002.499] initializing threads [0002.502] initializing timers [0002.504] creating bootstrap completion thread [0002.509] top of bootstrap2() [0002.512] CPU: ARM Cortex A57 [0002.515] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0002.519] initializing platform [0002.573] Config for emmc ddr50 mode completed [0002.578] sdmmc bdev is already initialized [0002.582] Enable APE clock [0002.584] Un-powergate APE partition [0002.588] of_register: registering tegra_udc to of_hal [0002.593] of_register: registering inv20628-driver to of_hal [0002.599] of_register: registering ads1015-driver to of_hal [0002.604] of_register: registering lp8557-bl-driver to of_hal [0002.610] of_register: registering bq2419x_charger to of_hal [0002.615] of_register: registering bq27441_fuel_gauge to of_hal [0002.627] gpio framework initialized [0002.630] of_register: registering tca9539_gpio to of_hal [0002.636] of_register: registering tca9539_gpio to of_hal [0002.641] of_register: registering i2c_bus_driver to of_hal [0002.647] of_register: registering i2c_bus_driver to of_hal [0002.652] of_register: registering i2c_bus_driver to of_hal [0002.658] pmic framework initialized [0002.661] of_register: registering max77620_pmic to of_hal [0002.667] regulator framework initialized [0002.671] of_register: registering tps65132_bl_driver to of_hal [0002.677] initializing target [0002.682] gpio_driver_register: register 'tegra_gpio_driver' driver [0002.691] board ID = D78, board SKU = 2 [0002.697] fixed regulator driver initialized [0002.714] initializing OF layer [0002.717] NCK carveout not present [0002.721] Skipping dts_overrides [0002.725] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.742] I2C Bus Init done [0002.744] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.755] I2C Bus Init done [0002.757] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.768] I2C Bus Init done [0002.770] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.781] I2C Bus Init done [0002.783] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.794] I2C Bus Init done [0002.796] of_children_init: Ops found for compatible string maxim,max77620 [0002.807] max77620_init using irq 118 [0002.812] register 'maxim,max77620' pmic [0002.816] gpio_driver_register: register 'max77620-gpio' driver [0002.822] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.833] I2C Bus Init done [0002.836] NCK carveout not present [0002.846] Find /i2c@7000c000's alias i2c0 [0002.850] get eeprom at 1-a0, size 256, type 0 [0002.859] Find /i2c@7000c500's alias i2c2 [0002.863] get eeprom at 3-a0, size 256, type 0 [0002.867] get eeprom at 3-ae, size 256, type 0 [0002.871] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.877] I2C slave not started [0002.880] I2C write failed [0002.882] Writing offset failed [0002.885] eeprom_init: EEPROM read failed [0002.889] pm_ids_update: eeprom init failed [0002.893] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.924] pm_ids_update: The pm board id is 3448-0002-400 [0002.930] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0002.938] pm_ids_update: pm id update successful [0002.943] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.948] I2C slave not started [0002.951] I2C write failed [0002.954] Writing offset failed [0002.957] eeprom_init: EEPROM read failed [0002.961] pm_ids_update: eeprom init failed [0002.991] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.997] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0003.005] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.011] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0003.019] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:dd:0e [0003.026] Plugin Manager: Parse ODM data 0x00094000 [0003.036] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [0003.060] Find /i2c@7000c000's alias i2c0 [0003.064] get eeprom at 1-a0, size 256, type 0 [0003.073] Find /i2c@7000c500's alias i2c2 [0003.077] get eeprom at 3-a0, size 256, type 0 [0003.081] get eeprom at 3-ae, size 256, type 0 [0003.086] pm_ids_update: Updating 1,a0, size 256, type 0 [0003.091] I2C slave not started [0003.094] I2C write failed [0003.097] Writing offset failed [0003.100] eeprom_init: EEPROM read failed [0003.103] pm_ids_update: eeprom init failed [0003.108] pm_ids_update: Updating 3,a0, size 256, type 0 [0003.138] pm_ids_update: The pm board id is 3448-0002-400 [0003.144] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0003.151] pm_ids_update: pm id update successful [0003.156] pm_ids_update: Updating 3,ae, size 256, type 0 [0003.161] I2C slave not started [0003.164] I2C write failed [0003.167] Writing offset failed [0003.170] eeprom_init: EEPROM read failed [0003.174] pm_ids_update: eeprom init failed [0003.204] Add serial number:1422819018726 as DT property [0003.212] Applying platform configs [0003.218] platform-init is not present. Skipping [0003.223] calling apps_init() [0003.239] Found 17 GPT partitions in "sdmmc3_user" [0003.243] Proceeding to Cold Boot [0003.247] starting app android_boot_app [0003.250] Device state: unlocked [0003.254] display console init [0003.262] could not find regulator [0003.265] hdmi cable connected [0003.298] DT entry for leds-pwm not found [0005.276] I2C transfer timeout [0005.279] I2C write failed [0005.281] Writing offset failed [0005.284] could not read edid [0005.289] tmds-config node not found [0005.293] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0005.308] setting 'vdd-1v8' regulator to 1800000 micro volts [0005.315] could not find regulator [0005.318] could not find regulator [0005.322] could not find regulator [0005.350] using default cmu settings [0005.354] dc_hdmi_enable, starting HDMI initialisation [0005.360] dc_hdmi_enable, HDMI initialisation complete [0005.365] list and configure display window [0005.370] display console init completed [0005.377] subnode volume_up is not found ! [0005.381] subnode back is not found ! [0005.385] subnode volume_down is not found ! [0005.389] subnode menu is not found ! [0005.393] Gpio keyboard init success [0005.440] found decompressor handler: lz4-legacy [0005.455] decompressing blob (type 1)... [0005.488] load_bmp_blob: panelresolution=480 type=0 [0005.538] decompressor handler not found [0005.542] load_firmware_blob: Firmware blob loaded, entries=2 [0005.548] -------> se_aes_verify_sbk_clear: 747 [0005.552] se_aes_verify_sbk_clear: Error [0005.556] bl_battery_charging: connected to external power supply [0005.564] xusb is supported [0005.570] error while finding nvidia,portmap [0006.074] xusb blob version 0 size 124416 [0006.078] firmware size 124416 [0006.083] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0006.094] xhci0: 64 bytes context size, 32-bit DMA [0006.134] usbus0: 5.0Gbps Super Speed USB v3.0 [0006.154] uhub0: on usbus0 [0006.804] uhub0: 9 ports with 9 removable, self powered [0007.804] failed to get HID devices [0007.808] failed to init xhci or no usb device attached [0007.822] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0007.829] MSC Partition not found [0007.839] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [0007.846] USP partition read failed! [0007.850] blob_init: blob-partition USP header read failed [0007.855] android_boot Unable to update recovery partition [0007.861] kfs_getpartname: name = LNX [0007.864] Loading kernel from LNX [0007.928] load kernel from storage [0007.938] decompressor handler not found [0007.957] Successfully loaded kernel and ramdisk images [0007.964] load_bmp_blob: panelresolution=480 type=0 [0008.037] display bmp image done [0008.040] NCK carveout not present [0008.044] Skipping dts_overrides [0008.047] NCK carveout not present [0008.057] Find /i2c@7000c000's alias i2c0 [0008.061] get eeprom at 1-a0, size 256, type 0 [0008.070] Find /i2c@7000c500's alias i2c2 [0008.074] get eeprom at 3-a0, size 256, type 0 [0008.078] get eeprom at 3-ae, size 256, type 0 [0008.082] pm_ids_update: Updating 1,a0, size 256, type 0 [0008.088] I2C slave not started [0008.091] I2C write failed [0008.093] Writing offset failed [0008.096] eeprom_init: EEPROM read failed [0008.100] pm_ids_update: eeprom init failed [0008.104] pm_ids_update: Updating 3,a0, size 256, type 0 [0008.134] pm_ids_update: The pm board id is 3448-0002-400 [0008.141] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0008.149] pm_ids_update: pm id update successful [0008.153] pm_ids_update: Updating 3,ae, size 256, type 0 [0008.159] I2C slave not started [0008.162] I2C write failed [0008.164] Writing offset failed [0008.168] eeprom_init: EEPROM read failed [0008.171] pm_ids_update: eeprom init failed [0008.202] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0008.208] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0008.216] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0008.222] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0008.230] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:dd:0e [0008.237] Plugin Manager: Parse ODM data 0x00094000 [0008.247] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [0008.265] Add serial number:1422819018726 as DT property [0008.274] "bpmp" doesn't exist, creating [0008.279] Updated bpmp info to DTB [0008.284] Updated initrd info to DTB [0008.288] "proc-board" doesn't exist, creating [0008.293] Updated board info to DTB [0008.296] "pmu-board" doesn't exist, creating [0008.302] Updated board info to DTB [0008.305] "display-board" doesn't exist, creating [0008.311] Updated board info to DTB [0008.314] "reset" doesn't exist, creating [0008.319] Updated reset info to DTB [0008.322] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb0000 is_hdmi_initialised=1 [0008.361] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [0008.377] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [0008.392] Updated bootarg info to DTB [0008.396] Adding uuid 00000001644495881c0000000c018340 to DT [0008.402] Adding eks info 0 to DT [0008.408] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0008.413] Updated memory info to DTB [0008.422] set vdd_core voltage to 1075 mv [0008.426] setting 'vdd-core' regulator to 1075000 micro volts [0008.444] Found secure-pmc; disable BPMP U-Boot 2016.07-g0536cf2a27 (Dec 09 2019 - 22:40:32 -0800) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000 *** Warning - spi_flash_probe() failed, using default environment In: serial Out: serial Err: serial Net: No ethernet found. MMC: no card present ** Bad device mmc 1 ** Hit any key to stop autoboot: 0 MMC: no card present switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 734 bytes read in 78 ms (8.8 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 5487751 bytes read in 174 ms (30.1 MiB/s) Retrieving file: /boot/Image 34191368 bytes read in 807 ms (40.4 MiB/s) ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 000000008317782f Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-2713) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Mon Dec 9 22:47:42 PST 2019 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00140000@92cb0000 [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefb1000 s61592 r8192 d32616 u102400 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb0000 is_hdmi_initialised=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29328(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3569136K/4159488K available (15230K kernel code, 2926K rwdata, 6620K rodata, 8576K init, 609K bss, 115216K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f60000 ( 15232 KB) [ 0.000000] .rodata : 0xffffff8008f60000 - 0xffffff80095e0000 ( 6656 KB) [ 0.000000] .init : 0xffffff80095e0000 - 0xffffff8009e40000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e40000 - 0xffffff800a11b808 ( 2927 KB) [ 0.000000] .bss : 0xffffff800a11b808 - 0xffffff800a1b3dbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.001755] Console: colour dummy device 80x25 [ 0.002614] console [tty0] enabled [ 0.002640] kmemleak: Kernel memory leak detector disabled [ 0.002669] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.002700] pid_max: default: 32768 minimum: 301 [ 0.003163] Security Framework initialized [ 0.003399] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003419] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.004639] ftrace: allocating 47001 entries in 184 pages [ 0.176811] ASID allocator initialised with 65536 entries [ 0.216028] tegra-id: chipid=22117. [ 0.216074] tegra-id: opt_subrevision=0. [ 0.216103] Tegra Speedo/IDDQ fuse revision 4 [ 0.216119] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.216135] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0 [ 0.216151] Tegra: CPU Speedo Value 2082, SoC Speedo Value 1982, GPU Speedo Value 2083 [ 0.216172] Tegra: CPU IDDQ Value 2396, SoC IDDQ Value 2604, GPU IDDQ Value 3270 [ 0.216206] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1 [ 0.216267] DTS File Name: /home/olex/nvidia/nvidia_sdk/JetPack_4.3_Linux_JETSON_NANO/Linux_for_Tegra/sources/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0002-p3449-0000-b00.dts [ 0.216309] DTB Build time: May 25 2020 11:30:33 [ 0.265047] CPU1: Booted secondary processor [411fd071] [ 0.296994] CPU2: Booted secondary processor [411fd071] [ 0.328944] CPU3: Booted secondary processor [411fd071] [ 0.329035] Brought up 4 CPUs [ 0.329098] SMP: Total of 4 processors activated. [ 0.329116] CPU features: detected feature: 32-bit EL0 Support [ 0.329391] CPU: All CPU(s) started at EL2 [ 0.329421] alternatives: patching kernel code [ 0.337516] devtmpfs: initialized [ 0.375003] Initilizing CustomIPI irq domain [ 0.375428] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.375474] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.386106] pinctrl core: initialized pinctrl subsystem [ 0.386797] OS set in device tree is not L4T. [ 0.387222] regulator-dummy: no parameters [ 0.387529] Initializing plugin-manager [ 0.387647] Plugin module not found [ 0.387890] node /plugin-manager/fragement@0 match with board >=3448-0002-100 [ 0.388470] node /plugin-manager/fragment@1 match with board >=3448-0002-101 [ 0.388986] node /plugin-manager/fragment@3 match with board >=3448-0002-100 [ 0.389746] node /plugin-manager/fragement@6 match with odm-data enable-tegra-wdt [ 0.390195] node /plugin-manager/fragement@8 match with odm-data enable-tegra-wdt [ 0.390841] node /plugin-manager/fragement@10 match with board >=3448-0002-300 [ 0.392989] node /plugin-manager/fragement@11 match with board >=3448-0002-300 [ 0.396377] NET: Registered protocol family 16 [ 0.397664] persistent_ram: found existing invalid buffer, size 33554432, start 0 [ 0.399108] pstore: using zlib compression [ 0.399781] console [pstore-1] enabled [ 0.399798] pstore: Registered ramoops as persistent store backend [ 0.399816] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.413067] cpuidle: using governor menu [ 0.417514] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.419155] vdso: 2 pages (1 code @ ffffff8008f67000, 1 data @ ffffff8009e44000) [ 0.419199] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.421553] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.424174] tegra_powergate_init: DONE [ 0.424214] DTS File Name: /home/olex/nvidia/nvidia_sdk/JetPack_4.3_Linux_JETSON_NANO/Linux_for_Tegra/sources/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0002-p3449-0000-b00.dts [ 0.424258] DTB Build time: May 25 2020 11:30:33 [ 0.426078] Tegra reboot handler registered. [ 0.430600] iommu: Adding device tegra-carveouts to group 0 [ 0.430773] platform tegra-carveouts: domain=ffffffc0f943a318 allocates as[0]=ffffffc0f9bd40a8 [ 0.431157] iommu: Adding device smmu_test to group 1 [ 0.431227] platform smmu_test: domain=ffffffc0f943a558 allocates as[0]=ffffffc0f9bd4110 [ 0.432061] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.432137] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.432209] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.432233] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.432270] mc-err: mcerr ops are set to t21x [ 0.442246] iommu: Adding device 70090000.xusb to group 2 [ 0.442569] iommu: Adding device 70006000.serial to group 3 [ 0.442664] platform 70006000.serial: domain=ffffffc0f94c6618 allocates as[0]=ffffffc0f9bd4178 [ 0.443111] iommu: Adding device 70006040.serial to group 4 [ 0.443406] iommu: Adding device 70006200.serial to group 5 [ 0.443635] iommu: Adding device sound to group 6 [ 0.443706] platform sound: domain=ffffffc0f94c6b58 allocates as[0]=ffffffc0f9bd41e0 [ 0.444291] iommu: Adding device 7000d400.spi to group 7 [ 0.444578] iommu: Adding device 7000d600.spi to group 8 [ 0.444948] iommu: Adding device 50000000.host1x to group 9 [ 0.445273] iommu: Adding device 54080000.vi to group 10 [ 0.445679] iommu: Adding device 54600000.isp to group 11 [ 0.445958] iommu: Adding device 54680000.isp to group 12 [ 0.446254] iommu: Adding device tegradc.0 to group 13 [ 0.446341] platform tegradc.0: domain=ffffffc0f94d3918 allocates as[0]=ffffffc0f9bd4248 [ 0.447746] platform tegradc.0: IOVA linear map 0x0000000092cb0000(140000) [ 0.448146] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.448498] iommu: Adding device tegradc.1 to group 14 [ 0.448565] platform tegradc.1: domain=ffffffc0f94d3b58 allocates as[0]=ffffffc0f9bd42b0 [ 0.450102] platform tegradc.1: IOVA linear map 0x0000000092cb0000(140000) [ 0.450508] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.450790] iommu: Adding device 54340000.vic to group 15 [ 0.451010] iommu: Adding device 544c0000.nvenc to group 16 [ 0.451223] iommu: Adding device 54500000.tsec to group 17 [ 0.451440] iommu: Adding device 54100000.tsecb to group 18 [ 0.451660] iommu: Adding device 54480000.nvdec to group 19 [ 0.451866] iommu: Adding device 54380000.nvjpg to group 20 [ 0.452977] iommu: Adding device 546c0000.i2c to group 21 [ 0.453360] iommu: Adding device 57000000.gpu to group 22 [ 0.453434] platform 57000000.gpu: domain=ffffffc0f94dfb58 allocates as[0]=ffffffc0f9bd4318 [ 0.453495] platform 57000000.gpu: domain=ffffffc0f94dfb58 allocates as[1]=ffffffc0f9bd4380 [ 0.453556] platform 57000000.gpu: domain=ffffffc0f94dfb58 allocates as[2]=ffffffc0f9bd43e8 [ 0.453615] platform 57000000.gpu: domain=ffffffc0f94dfb58 allocates as[3]=ffffffc0f9bd4450 [ 0.454515] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.454555] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.454582] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET [ 0.454603] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.454620] tegra-pmc: ### PMC reset status reg: 0x3 [ 0.505157] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.505191] tegra-pmc: Clear bootloader IO dpd settings [ 0.505224] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.505308] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.505628] iommu: Adding device 70012000.se to group 23 [ 0.506420] iommu: Adding device 7000c000.i2c to group 24 [ 0.506705] iommu: Adding device 7000c400.i2c to group 25 [ 0.506974] iommu: Adding device 7000c500.i2c to group 26 [ 0.507253] iommu: Adding device 7000c700.i2c to group 27 [ 0.507515] iommu: Adding device 7000d000.i2c to group 28 [ 0.507810] iommu: Adding device 7000d100.i2c to group 29 [ 0.508093] iommu: Adding device sdhci-tegra.3 to group 30 [ 0.508166] platform sdhci-tegra.3: domain=ffffffc0f956fcd8 allocates as[0]=ffffffc0f9bd44b8 [ 0.509062] iommu: Adding device 700d0000.xudc to group 31 [ 0.512441] vdd-ac-bat: 5000 mV [ 0.512828] vdd-5v0-sys: 5000 mV [ 0.513843] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.513938] vdd-5v0-hdmi: 5000 mV [ 0.514354] vdd-1v8-sys: 1800 mV [ 0.514768] vdd-fan: supplied by vdd-5v0-sys [ 0.514820] vdd-fan: 5000 mV [ 0.515202] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.515270] vdd-usb-vbus: 5000 mV [ 0.515801] vdd-usb-vbus2: 5000 mV [ 0.546037] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.548487] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.549727] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.549766] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.549819] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.550176] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.557911] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.558279] SCSI subsystem initialized [ 0.558803] usbcore: registered new interface driver usbfs [ 0.558873] usbcore: registered new interface driver hub [ 0.558961] usbcore: registered new device driver usb [ 0.562859] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.568354] vdd-core: 600 <--> 1162 mV at 1075 mV [ 0.568533] random: fast init done [ 0.569405] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.572256] vdd-ddr-1v1: 1150 mV [ 0.576331] vdd-pre-reg-1v35: 1350 mV [ 0.580245] vdd-1v8: 1800 mV [ 0.584244] avdd-sys-1v2: 1200 mV [ 0.588245] vdd-pex-1v0: 1050 mV [ 0.588979] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.589536] max77620-ldo3: at 3100 mV [ 0.592246] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.592801] max77620-ldo5: at 3100 mV [ 0.596250] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [ 0.600241] avdd-1v05-pll: 1050 mV [ 0.604241] avdd-io-hdmi-dp: 1050 mV [ 0.606893] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.607215] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.607531] max77620 4-003c: max77620 probe successful [ 0.610209] media: Linux media interface: v0.10 [ 0.610285] Linux video capture interface: v2.00 [ 0.611205] pps_core: LinuxPPS API ver. 1 registered [ 0.611234] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.611276] PTP clock support registered [ 0.615036] tegra_fiq_debugger_init: found FIQ source (IRQ 97) [ 0.621442] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.622348] Advanced Linux Sound Architecture Driver Initialized. [ 0.623012] Bluetooth: Core ver 2.22 [ 0.623078] NET: Registered protocol family 31 [ 0.623096] Bluetooth: HCI device and connection manager initialized [ 0.623125] Bluetooth: HCI socket layer initialized [ 0.623146] Bluetooth: L2CAP socket layer initialized [ 0.623190] Bluetooth: SCO socket layer initialized [ 0.624899] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.624940] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.624996] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.625024] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.628308] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.629533] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.629639] vdd-3v3-sys: 3300 mV [ 0.629920] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.632307] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.632785] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.632842] vdd-3v3-sd: 3300 mV [ 0.633963] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.634024] avdd-io-edp-1v05: 1050 mV [ 0.634467] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.634524] vdd-usb-hub-en: 5000 mV [ 0.635907] camchar: rtcpu character device driver loaded [ 0.636637] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [ 0.637992] clocksource: Switched to clocksource arch_sys_counter [ 0.677646] VFS: Disk quotas dquot_6.6.0 [ 0.677818] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.678380] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.678815] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.678863] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.679086] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.679110] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.679136] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.679187] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.679214] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.679247] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.679269] nvmap_page_pool_init: Total RAM pages: 1011068 [ 0.679286] nvmap_page_pool_init: nvmap page pool size: 126383 pages (493 MB) [ 0.679402] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.679836] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.680804] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.689141] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.689579] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.689841] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.690089] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.690289] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.690569] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.690591] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.691043] NET: Registered protocol family 2 [ 0.692045] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.692285] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.692790] TCP: Hash tables configured (established 32768 bind 32768) [ 0.692956] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.693054] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.693473] NET: Registered protocol family 1 [ 0.694366] RPC: Registered named UNIX socket transport module. [ 0.694398] RPC: Registered udp transport module. [ 0.694414] RPC: Registered tcp transport module. [ 0.694430] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.694682] Trying to unpack rootfs image as initramfs... [ 0.927020] Freeing initrd memory: 5356K [ 0.937043] host1x 50000000.host1x: initialized [ 0.938975] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.942238] audit: initializing netlink subsys (disabled) [ 0.942340] audit: type=2000 audit(0.795:1): initialized [ 0.943078] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 0.953210] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.954767] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.955590] 9p: Installing v9fs 9p2000 file system support [ 0.958929] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 0.959098] io scheduler noop registered [ 0.959411] io scheduler cfq registered (default) [ 0.962333] gic 702f9000.agic: GIC IRQ controller registered [ 0.965331] iommu: Adding device 702ef000.adsp to group 32 [ 0.974426] iommu: Adding device aconnect@702c0000:adsp_audio to group 33 [ 0.974658] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 0.975325] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x71c7c0f [ 0.975358] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 0.976971] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 0.977108] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 0.977221] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 0.977436] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 0.977552] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 0.977660] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 0.977771] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 0.977878] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 0.978040] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 0.978154] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 0.984206] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 0.985920] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 0.987861] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 0.989168] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 0.989542] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 0.990930] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 0.991177] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 0.991446] Adding domain tsec-pd to PM domain host1x-pd [ 0.993692] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 0.994668] tsec 54500000.tsec: initialized [ 0.996279] tsec 54100000.tsecb: initialized [ 0.997004] Adding domain nvdec-pd to PM domain host1x-pd [ 1.000573] nvdec 54480000.nvdec: initialized [ 1.001668] Adding domain vic03-pd to PM domain host1x-pd [ 1.001870] Adding domain msenc-pd to PM domain host1x-pd [ 1.002087] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.006393] falcon 54340000.vic: initialized [ 1.007649] falcon 544c0000.nvenc: initialized [ 1.009011] falcon 54380000.nvjpg: initialized [ 1.013322] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=96 [ 1.013401] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.013449] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.013575] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.013718] display board info: id 0x0, fab 0x0 [ 1.013726] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.013730] tegra_cec 70015000.tegra_cec: probed [ 1.013830] generic_infoframe_type: 0x87 [ 1.014109] tegradc tegradc.0: DT parsed successfully [ 1.014169] tegradc tegradc.0: Display dc.ffffff800ab40000 registered with id=0 [ 1.014745] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 640x480 (on 0x0mm) pclk=25173906 [ 1.021746] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.022310] tegradc tegradc.0: probed [ 1.028197] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.029642] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.030130] kfuse 7000fc00.kfuse: initialized [ 1.031712] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.032726] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.034242] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.034290] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.034789] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.036465] vdd-gpu: applied init 1000000uV constraint [ 1.036494] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.036913] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.041555] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.041792] No Device Node present for smmu client: serial8250 !! [ 1.041823] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.041911] iommu: Adding device serial8250 to group 34 [ 1.044702] console [ttyS0] disabled [ 1.044796] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.505660] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.910118] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.038011] tegra_cec 70015000.tegra_cec: Can't find physical addresse. [ 2.038016] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 2.313571] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.315588] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.421745] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.421754] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.421760] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.421765] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.421771] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.422209] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.442094] pci 0000:00:02.0: BAR 15: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.442099] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.442109] pci 0000:01:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.442129] pci 0000:01:00.0: BAR 2: assigned [mem 0x20004000-0x20004fff 64bit pref] [ 2.442147] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.442158] pci 0000:00:02.0: PCI bridge to [bus 01] [ 2.442164] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.442172] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.442523] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 2.442528] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 3.521576] console [ttyS0] enabled [ 3.521957] Console: switching to colour frame buffer device 80x30 [ 3.531779] tegradc tegradc.0: fb registered [ 3.532888] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 3.533239] serial-tegra 70006200.serial: RX in PIO mode [ 3.533334] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 3.534442] [drm] Initialized [ 3.564945] brd: module loaded [ 3.569163] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [ 3.573532] loop: module loaded [ 3.573633] tegra_profiler: version: 1.139, samples/io: 47/27 [ 3.573748] tegra_profiler: auth: init [ 3.575058] THERMAL EST: found 2 subdevs [ 3.575065] THERMAL EST num_resources: 0 [ 3.575077] [THERMAL EST subdev 0] [ 3.575084] [THERMAL EST subdev 1] [ 3.575539] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 3.575542] THERMAL EST: thz register success. [ 3.575700] THERMAL EST: end of probe, return err: 0 [ 3.577000] hisi_sas: driver version v1.6 [ 3.587318] libphy: Fixed MDIO Bus: probed [ 3.588263] tun: Universal TUN/TAP device driver, 1.6 [ 3.588267] tun: (C) 1999-2004 Max Krasnyansky [ 3.589323] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 3.589327] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.589382] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 3.589384] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.589435] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 3.589438] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.589492] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 3.589495] Copyright(c) 1999 - 2017 Intel Corporation. [ 3.590451] r8168 0000:01:00.0: enabling device (0000 -> 0003) [ 3.590481] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 3.612055] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 3.612236] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e5:dd:0e from device tree [ 3.612834] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 3.612896] r8168 Copyright (C) 2017 Realtek NIC software team [ 3.612896] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 3.612896] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 3.613485] PPP generic driver version 2.4.2 [ 3.613696] PPP BSD Compression module registered [ 3.613700] PPP Deflate Compression module registered [ 3.613740] PPP MPPE Compression module registered [ 3.613746] NET: Registered protocol family 24 [ 3.613823] usbcore: registered new interface driver r8152 [ 3.613876] usbcore: registered new interface driver asix [ 3.613937] usbcore: registered new interface driver ax88179_178a [ 3.614064] usbcore: registered new interface driver cdc_ether [ 3.614111] usbcore: registered new interface driver net1080 [ 3.614148] usbcore: registered new interface driver cdc_subset [ 3.614185] usbcore: registered new interface driver zaurus [ 3.614237] usbcore: registered new interface driver cdc_ncm [ 3.614444] VFIO - User Level meta-driver version: 0.3 [ 3.615810] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.615833] ehci-pci: EHCI PCI platform driver [ 3.615881] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.615890] ohci-pci: OHCI PCI platform driver [ 3.615937] ohci-platform: OHCI generic platform driver [ 3.618681] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 3.619280] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 3.620423] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f90ee400 id [ 3.622661] usbcore: registered new interface driver uas [ 3.622724] usbcore: registered new interface driver usb-storage [ 3.622873] usbcore: registered new interface driver usbserial [ 3.623281] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release [ 3.623333] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.623359] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 3.624125] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 3.624185] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 3.624399] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.624405] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.624410] usb usb1: Product: xHCI Host Controller [ 3.624413] usb usb1: Manufacturer: Linux 4.9.140-tegra xhci-hcd [ 3.624417] usb usb1: SerialNumber: 70090000.xusb [ 3.625039] hub 1-0:1.0: USB hub found [ 3.625083] hub 1-0:1.0: 5 ports detected [ 3.625651] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.625662] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 3.625734] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.625831] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 3.625836] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.625840] usb usb2: Product: xHCI Host Controller [ 3.625843] usb usb2: Manufacturer: Linux 4.9.140-tegra xhci-hcd [ 3.625846] usb usb2: SerialNumber: 70090000.xusb [ 3.626443] hub 2-0:1.0: USB hub found [ 3.626478] hub 2-0:1.0: 4 ports detected [ 3.629129] tegra-xudc-new 700d0000.xudc: device count: 1 [ 3.630455] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 3.630471] tegra-xudc-new 700d0000.xudc: vbus state: 0 [ 3.630506] tegra-xudc-new 700d0000.xudc: entering ELPG [ 3.630748] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 3.631421] mousedev: PS/2 mouse device common for all mice [ 3.631527] usbcore: registered new interface driver xpad [ 3.726192] usb usb1: usb_suspend_both: status 0 [ 3.862066] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 3.873846] rtc rtc1: alarm rtc device [ 3.873864] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 3.873897] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 3.874565] i2c /dev entries driver [ 3.876692] i2c i2c-6: Added multiplexed i2c bus 7 [ 3.877128] i2c i2c-6: Added multiplexed i2c bus 8 [ 3.877135] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 3.877872] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [ 3.902014] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 3.902092] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 3.902129] imx219 7-0010: board setup failed [ 3.902224] imx219: probe of 7-0010 failed with error -121 [ 3.902767] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [ 3.930609] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 3.930692] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 3.930720] imx219 8-0010: board setup failed [ 3.930780] imx219: probe of 8-0010 failed with error -121 [ 3.939351] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 3.979536] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 3.979540] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 3.979970] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.979987] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 3.979996] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 3.980129] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.980138] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 3.980145] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 3.980292] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.980302] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 3.980307] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 3.980513] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 3.981287] tegra_aotag tegra-aotag: Registering sensor 0 [ 3.981342] tegra_aotag tegra-aotag: Invalid temp readout [ 3.981369] tegra_aotag tegra-aotag: Invalid temp readout [ 3.981386] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 3.981395] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 3.982343] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.982362] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 3.982545] tegra_aotag tegra-aotag: Invalid temp readout [ 3.982577] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 3.982988] parse_throttle_dt_data: Num cap clks = 6 [ 3.982994] parse_throttle_dt_data: clk=cclk_g type=2 [ 3.983007] parse_throttle_dt_data: clk=gpu type=4 [ 3.983030] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 3.983048] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 3.983068] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 3.983071] parse_throttle_dt_data: clk=emc type=3 [ 3.988402] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.988501] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.988631] tegra_throttle_probe: probe successful. #cdevs=4 [ 3.989387] FAN dev name: pwm-fan [ 3.989468] FAN:gpio request success. [ 3.989544] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 3.989848] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 3.990036] pwm_fan_driver pwm-fan: fan tach request irq success [ 3.990044] pwm_fan_driver pwm-fan: tach period: 1000 [ 3.990149] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 3.990153] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 3.990157] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 3.990161] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 3.990165] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 3.990169] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 3.990173] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 3.990176] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 3.990180] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 3.990185] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 3.990818] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds. [ 3.991193] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1) [ 3.992107] device-mapper: uevent: version 1.0.3 [ 3.992591] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 3.998003] tegra210-cpufreq cpufreq: probe()...completed [ 3.998701] sdhci: Secure Digital Host Controller Interface driver [ 3.998702] sdhci: Copyright(c) Pierre Ossman [ 3.998703] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.999063] sdhci-tegra sdhci-tegra.3: Client registration for eMC Successful [ 4.004093] tegra-se 70012000.se: tegra_se_probe: complete [ 4.004647] hidraw: raw HID events driver (C) Jiri Kosina [ 4.006176] usbcore: registered new interface driver usbhid [ 4.006178] usbhid: USB HID core driver [ 4.030073] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 4.030330] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 4.032054] nvpmodel: initialized successfully [ 4.033014] usbcore: registered new interface driver snd-usb-audio [ 4.033077] No Device Node present for smmu client: snd-soc-dummy !! [ 4.033081] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 4.033097] iommu: Adding device snd-soc-dummy to group 35 [ 4.062065] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA 64-bit with 64 bit addr [ 4.081352] OPE platform probe [ 4.081432] OPE platform probe successful [ 4.082440] OPE platform probe [ 4.082520] OPE platform probe successful [ 4.083464] tegra-asoc: sound: Can't retrieve clk ahub [ 4.083480] tegra-asoc:: probe of sound failed with error -2 [ 4.083813] u32 classifier [ 4.083814] Actions configured [ 4.083885] Initializing XFRM netlink socket [ 4.084598] NET: Registered protocol family 10 [ 4.085341] NET: Registered protocol family 17 [ 4.085352] NET: Registered protocol family 15 [ 4.085426] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.085472] Bluetooth: RFCOMM socket layer initialized [ 4.085479] Bluetooth: RFCOMM ver 1.11 [ 4.085483] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.085487] Bluetooth: HIDP socket layer initialized [ 4.085505] 9pnet: Installing 9P2000 support [ 4.085537] Key type dns_resolver registered [ 4.086127] Registered cp15_barrier emulation handler [ 4.086216] Registered setend emulation handler [ 4.087413] registered taskstats version 1 [ 4.087978] Adding domain ve2-pd to PM domain host1x-pd [ 4.088214] Adding domain ve-pd to PM domain host1x-pd [ 4.185868] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 4.284418] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 4.288939] mmcblk0: mmc0:0001 DG4016 14.7 GiB [ 4.293233] mmcblk0boot0: mmc0:0001 DG4016 partition 1 4.00 MiB [ 4.297480] mmcblk0boot1: mmc0:0001 DG4016 partition 2 4.00 MiB [ 4.297589] mmcblk0rpmb: mmc0:0001 DG4016 partition 3 4.00 MiB [ 4.315541] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 [ 4.819608] tegradc tegradc.0: hdmi: tmds rate:25174K prod-setting:prod_c_hdmi_0m_54m [ 4.827752] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [ 4.834894] tegradc tegradc.0: hdmi: BL set VIC 0 [ 4.839605] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [ 7.790628] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 7.796455] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 7.894182] usb usb2: usb_suspend_both: status 0 [ 10.098041] tegra-xusb 70090000.xusb: entering ELPG [ 10.103921] tegra-pmc: PMC tegra_pmc_utmi_phy_enable_sleepwalk : port 1, speed 0 [ 10.111499] tegra-pmc: PMC tegra_pmc_utmi_phy_enable_sleepwalk : port 2, speed 0 [ 10.120392] tegra-xusb 70090000.xusb: entering ELPG done [ 14.962041] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 14.968490] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 14.975198] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 14.980341] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 14.987038] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 14.992608] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 14.998442] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 15.003666] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 15.009001] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 15.015553] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 15.021645] Extcon AUX1(HDMI) enable [ 15.025665] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 15.032073] tegradc tegradc.1: No lt-data, using default setting [ 15.032116] edid invalid [ 15.040614] tegradc tegradc.1: No hpd-gpio in DT [ 15.045248] tegradc tegradc.1: DT parsed successfully [ 15.050317] tegradc tegradc.1: Display dc.ffffff800d4c0000 registered with id=1 [ 15.058480] tegradc tegradc.1: dpd enable lookup fail:-19 [ 15.058521] tegradc tegradc.0: nominal-pclk:25174825 parent:25173906 div:1.0 pclk:25173906 24923052~27440532 [ 15.077850] tegradc tegradc.1: probed [ 15.081686] tegradc tegradc.1: fb registered [ 15.089075] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 15.091170] isp 54600000.isp: initialized [ 15.091928] isp 54680000.isp: initialized [ 15.102073] last reset is due to software reset [ 15.102076] KERNEL: PMC reset status reg: 0x3 [ 15.102150] BL: PMC reset status reg: 0x3 [ 15.102152] BL: PMIC poweroff Event Recorder: 0x0 [ 15.103595] clk_cbus_recalc_rate: no gbus parent [ 15.103599] clk_cbus_round_rate: no gbus parent [ 15.103601] clk_cbus_round_rate: no gbus parent [ 15.103607] clk_cbus_recalc_rate: no gbus parent [ 15.103704] clk_cbus_recalc_rate: no gbus parent [ 15.103707] clk_cbus_round_rate: no gbus parent [ 15.103708] clk_cbus_round_rate: no gbus parent [ 15.103711] clk_cbus_recalc_rate: no gbus parent [ 15.103724] tegra_dvfs: GPU-cap: registered [ 15.103783] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 15.103785] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled [ 15.103787] tegra dvfs: vdd-gpu: nominal 1058mV, offset 708000uV, step 10000uV, scaling enabled [ 15.149552] tegra_dvfs: vdd-gpu-vts: registered [ 15.180252] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 15.180878] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 15.181382] input: gpio-keys as /devices/gpio-keys/input/input1 [ 15.217423] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 15.225778] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:28:11 UTC (946690091) [ 15.235761] vi 54080000.vi: vi_probe: ++ [ 15.238085] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 15.245197] tegradc tegradc.1: blank - powerdown [ 15.249843] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 15.257075] Extcon DP: HPD disabled [ 15.260575] hpd: hpd_switch 0 [ 15.263553] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 15.270176] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 15.276107] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 15.284525] vi 54080000.vi: initialized [ 15.290530] vi 54080000.vi: subdev nvcsi--2 bound [ 15.295349] vi 54080000.vi: subdev nvcsi--1 bound [ 15.300272] mmcblk mmc0:0001: Card claimed for testing. [ 15.306820] Disable partitions left on by BL [ 15.311103] disb [ 15.313158] bwmgr: missing cdev-type property [ 15.317610] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 15.326914] DRAM derating cdev registered. [ 15.332035] vdd-fan: disabling [ 15.335100] vdd-usb-vbus: disabling [ 15.338591] vdd-usb-vbus2: disabling [ 15.342171] vddio-sdmmc-ap: disabling [ 15.345956] vddio-sdmmc3-ap: disabling [ 15.349834] vdd-3v3-sd: disabling [ 15.353159] avdd-io-edp-1v05: disabling [ 15.356997] vdd-usb-hub-en: disabling [ 15.360791] ALSA device list: [ 15.363770] #0: tegra-hda at 0x70038000 irq 82 [ 15.371488] Freeing unused kernel memory: 8576K [ 15.396608] Root device found: mmcblk0p1 [ 15.401595] Found dev node: /dev/mmcblk0p1 [ 15.424772] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 15.433607] Rootfs mounted over mmcblk0p1 [ 15.452937] Switching from initrd to actual rootfs [ 15.534339] systemd[1]: System time before build time, advancing clock. [ 15.555760] ip_tables: (C) 2000-2006 Netfilter Core Team [ 15.572075] cgroup: cgroup2: unknown option "nsdelegate" [ 15.584741] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 15.606860] systemd[1]: Detected architecture arm64. [ 15.637698] systemd[1]: No hostname configured. [ 15.642258] systemd[1]: Set hostname to . [ 15.650249] random: systemd: uninitialized urandom read (16 bytes read) [ 15.656884] systemd[1]: Initializing machine ID from random generator. [ 15.734586] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 15.751777] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 15.863286] random: systemd: uninitialized urandom read (16 bytes read) [ 15.869948] systemd[1]: Reached target Swap. [ 15.874773] random: systemd: uninitialized urandom read (16 bytes read) [ 15.883225] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 15.894606] systemd[1]: Created slice System Slice. [ 15.978435] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 16.027564] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [ 16.680924] using random self ethernet address [ 16.685440] using random host ethernet address [ 16.973099] random: crng init done [ 16.976507] random: 7 urandom warning(s) missed due to ratelimiting [ 17.042118] using random self ethernet address [ 17.054134] using random host ethernet address [ 19.228776] Please complete system configuration setup on desktop to proceed... [ 25.458089] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 25.464560] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 25.471311] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 25.476482] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 25.483214] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 25.488816] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 25.494686] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 25.499943] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 25.505310] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 25.837755] edid invalid [ 35.698054] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 35.698057] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 35.698061] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 35.698063] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 35.698066] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 35.698068] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 35.698071] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 35.698073] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 35.698102] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 45.938051] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 45.938054] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 45.938057] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 45.938059] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 45.938061] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 45.938064] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 45.938066] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 45.938068] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 45.938096] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 56.178007] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 56.184483] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 56.191223] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 56.196386] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 56.203114] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 56.208711] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 56.214574] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 56.219834] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 56.225194] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 66.418054] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 66.424501] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 66.431216] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 66.436370] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 66.443071] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 66.448650] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 66.454484] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 66.459711] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 66.465055] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 76.658015] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 76.664496] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 76.671206] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 76.676356] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 76.683064] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 76.688639] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 76.694477] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 76.699703] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 76.705042] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 86.898054] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 86.904506] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 86.911215] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 86.916360] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 86.923065] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 86.928639] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 86.934476] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 86.939704] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 86.945041] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 97.138051] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 97.144494] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 97.151207] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 97.156350] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 97.163056] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 97.168628] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 97.174461] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 97.179690] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 97.185029] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 107.378054] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 107.384498] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 107.391212] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 107.396357] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 107.403057] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 107.408643] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 107.414478] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 107.419703] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 107.425044] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 117.618010] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 117.624458] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 117.631165] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 117.636316] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 117.643021] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 117.648596] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 117.654434] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 117.659660] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 117.664999] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 127.858062] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 127.864515] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 127.871223] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 127.876373] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 127.883082] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 127.888658] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 127.894495] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 127.899721] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 127.905060] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 127.911975] tegradc tegradc.0: hdmi: edid read failed [ 138.098058] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 138.098062] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 138.098065] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 138.098067] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 138.098070] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 138.098072] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 138.098075] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 138.098077] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 138.098106] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 148.338060] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 148.338063] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 148.338066] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 148.338069] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 148.338071] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 148.338074] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 148.338076] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 148.338079] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 148.338107] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 158.578061] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 158.578064] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 158.578068] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 158.578071] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 158.578073] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 158.578076] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 158.578078] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 158.578081] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 158.578109] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50