▒[0000.230] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb) [0000.235] Processing in cold boot mode Bootloader 2 [0000.240] A02 Bootrom Patch rev = 1023 [0000.243] Power-up reason: pmc por [0000.247] No Battery Present [0000.249] pmic max77620 reset reason [0000.253] pmic max77620 NVERC : 0x40 [0000.256] RamCode = 0 [0000.258] Platform has DDR4 type RAM [0000.262] max77620 disabling SD1 Remote Sense [0000.266] Setting DDR voltage to 1125mv [0000.270] Serial Number of Pmic Max77663: 0xd0a2e [0000.277] Entering ramdump check [0000.280] Get RamDumpCarveOut = 0x0 [0000.284] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.289] Last reboot was clean, booting normally! [0000.293] Sdram initialization is successful [0000.297] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.304] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.309] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.315] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.321] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.327] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.333] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.339] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.355] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.361] Platform-DebugCarveout: 0 [0000.364] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.370] Non secure mode, and RB not enabled. [0000.374] *** Booting BFS0. [0000.377] Initialize FailControl [0000.380] Read PT from (0:3) [0000.395] Csd NumOfBlocks=0 [0000.434] PT crc32 and magic check passed. [0000.438] Using BFS PT to query partitions [0000.442] PT: Partition LNX NOT found ! [0000.446] *** Booting KFS0. [0000.448] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.454] BoardID = 3448, SKU = 0x2 [0000.458] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0000.463] Read GPT from (0:3) [0000.471] Using GPT Primary to query partitions [0000.476] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.483] Loading Tboot-CPU binary [0000.488] Verifying TBC in OdmNonSecureSBK mode [0000.498] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.505] Bootloader downloaded successfully. [0000.510] Downloaded Tboot-CPU binary to 0xa0000258 [0000.515] MAX77620_GPIO5 configured [0000.518] CPU power rail is up [0000.521] CPU clock enabled [0000.525] Performing RAM repair [0000.527] Updating A64 Warmreset Address to 0xa00002e9 [0000.532] BoardID = 3448, SKU = 0x2 [0000.536] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0000.542] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.548] Loading NvTbootBootloaderDTB [0000.565] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.631] Bootloader DTB Load Address: 0x83000000 [0000.636] BoardID = 3448, SKU = 0x2 [0000.639] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0000.645] Loading NvTbootKernelDTB [0000.662] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.728] Kernel DTB Load Address: 0x83100000 [0000.732] BoardID = 3448, SKU = 0x2 [0000.735] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0000.741] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.748] Loading cboot binary [0000.759] Verifying EBT in OdmNonSecureSBK mode [0000.801] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.808] Bootloader downloaded successfully. [0000.812] BoardID = 3448, SKU = 0x2 [0000.815] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0000.821] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.828] PT: Partition NCT NOT found ! [0000.831] Warning: Find Partition via PT Failed [0000.836] Next binary entry address: 0x92c00258 [0000.840] BoardId: 3448 [0000.845] Overriding pmu board id with proc board id [0000.849] Display board id is not available [0000.854] BoardID = 3448, SKU = 0x2 [0000.857] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0000.863] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.876] Verifying SC7EntryFw in OdmNonSecureSBK mode [0000.930] /bpmp deleted [0000.933] SC7EntryFw header found loaded at 0xff700000 [0001.117] OVR2 PMIC [0001.119] Bpmp FW successfully loaded [0001.122] BoardID = 3448, SKU = 0x2 [0001.125] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.131] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.138] WB0 init successfully at 0xff780000 [0001.143] Verifying NvTbootWb0 in OdmNonSecureSBK mode [0001.148] Set NvDecSticky Bits [0001.151] GSC2 address ff53fffc value c0edbbcc [0001.158] GSC MC Settings done [0001.160] BoardID = 3448, SKU = 0x2 [0001.164] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.170] TOS Image length 53680 [0001.174] Monitor size 53680 [0001.176] OS size 0 [0001.182] Secure Os AES-CMAC Verification Success! [0001.186] TOS image cipher info: plaintext [0001.190] Loading and Validation of Secure OS Successful [0001.206] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.211] NvTbootPackSdramParams: start. [0001.216] NvTbootPackSdramParams: done. [0001.220] Tegraboot started after 159478 us [0001.224] Basic modules init took 730927 us [0001.228] Sec Bootdevice Read Time = 54 ms, Read Size = 3682 KB [0001.233] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.239] Next stage binary read took 7390 us [0001.243] Carveout took -34782 us [0001.246] CPU initialization took 386184 us [0001.250] Total time taken by TegraBoot 1089719 us [0001.255] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:09:37, Jul 26 2021 ERROR: Error initializing runtime service trusty_fast [0001.377] RamCode = 0 [0001.382] LPDDR4 Training: Read DT: Number of tables = 2 [0001.387] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.399] EMC Training Successful [0001.402] 408000 not found in DVFS table [0001.409] RamCode = 0 [0001.412] DT Write: emc-table@204000 succeeded [0001.418] DT Write: emc-table@1600000 succeeded [0001.422] LPDDR4 Training: Write DT: Number of tables = 2 [0001.465] [0001.466] Debug Init done [0001.468] Marked DTB cacheable [0001.471] Bootloader DTB loaded at 0x83000000 [0001.476] Marked DTB cacheable [0001.479] Kernel DTB loaded at 0x83100000 [0001.483] DeviceTree Init done [0001.496] Pinmux applied successfully [0001.500] gicd_base: 0x50041000 [0001.504] gicc_base: 0x50042000 [0001.507] Interrupts Init done [0001.511] Using base:0x60005090 & irq:208 for tick-timer [0001.516] Using base:0x60005098 for delay-timer [0001.520] platform_init_timer: DONE [0001.524] Timer(tick) Init done [0001.528] osc freq = 38400 khz [0001.531] [0001.532] Welcome to L4T Cboot [0001.535] [0001.537] Cboot Version: 00.00.2018.01-t210-c952b4e6 [0001.542] calling constructors [0001.544] initializing heap [0001.547] initializing threads [0001.550] initializing timers [0001.553] creating bootstrap completion thread [0001.557] top of bootstrap2() [0001.560] CPU: ARM Cortex A57 [0001.563] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.568] initializing platform [0001.621] Config for emmc ddr50 mode completed [0001.626] sdmmc bdev is already initialized [0001.630] Enable APE clock [0001.632] Un-powergate APE partition [0001.636] of_register: registering tegra_udc to of_hal [0001.641] of_register: registering inv20628-driver to of_hal [0001.647] of_register: registering ads1015-driver to of_hal [0001.652] of_register: registering lp8557-bl-driver to of_hal [0001.658] of_register: registering bq2419x_charger to of_hal [0001.664] of_register: registering bq27441_fuel_gauge to of_hal [0001.675] gpio framework initialized [0001.678] of_register: registering tca9539_gpio to of_hal [0001.683] of_register: registering tca9539_gpio to of_hal [0001.689] of_register: registering i2c_bus_driver to of_hal [0001.694] of_register: registering i2c_bus_driver to of_hal [0001.700] of_register: registering i2c_bus_driver to of_hal [0001.706] pmic framework initialized [0001.709] of_register: registering max77620_pmic to of_hal [0001.714] regulator framework initialized [0001.718] of_register: registering tps65132_bl_driver to of_hal [0001.724] initializing target [0001.730] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.741] fixed regulator driver initialized [0001.758] initializing OF layer [0001.761] NCK carveout not present [0001.764] Skipping dts_overrides [0001.768] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.784] I2C Bus Init done [0001.786] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.796] I2C Bus Init done [0001.799] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.809] I2C Bus Init done [0001.812] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.822] I2C Bus Init done [0001.825] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.835] I2C Bus Init done [0001.837] of_children_init: Ops found for compatible string maxim,max77620 [0001.848] max77620_init using irq 118 [0001.853] register 'maxim,max77620' pmic [0001.857] gpio_driver_register: register 'max77620-gpio' driver [0001.863] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.873] I2C Bus Init done [0001.877] NCK carveout not present [0001.886] Find /i2c@7000c000's alias i2c0 [0001.890] get eeprom at 1-a0, size 256, type 0 [0001.898] Find /i2c@7000c500's alias i2c2 [0001.902] get eeprom at 3-a0, size 256, type 0 [0001.907] get eeprom at 3-ae, size 256, type 0 [0001.911] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.916] I2C slave not started [0001.919] I2C write failed [0001.922] Writing offset failed [0001.925] eeprom_init: EEPROM read failed [0001.929] pm_ids_update: eeprom init failed [0001.933] pm_ids_update: Updating 3,a0, size 256, type 0 [0003.938] I2C transfer timeout [0003.941] I2C write failed [0003.944] Writing offset failed [0003.947] eeprom_init: EEPROM read failed [0003.951] pm_ids_update: eeprom init failed [0003.955] pm_ids_update: Updating 3,ae, size 256, type 0 [0005.960] I2C transfer timeout [0005.963] I2C write failed [0005.966] Writing offset failed [0005.969] eeprom_init: EEPROM read failed [0005.973] pm_ids_update: eeprom init failed [0007.977] I2C transfer timeout [0007.980] I2C write failed [0007.983] Writing offset failed [0007.986] eeprom_init: EEPROM read failed [0007.990] Plugin Manager: Parse ODM data 0x000a4000 [0008.001] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0008.016] Find /i2c@7000c000's alias i2c0 [0008.019] get eeprom at 1-a0, size 256, type 0 [0008.028] Find /i2c@7000c500's alias i2c2 [0008.032] get eeprom at 3-a0, size 256, type 0 [0008.036] get eeprom at 3-ae, size 256, type 0 [0008.041] pm_ids_update: Updating 1,a0, size 256, type 0 [0008.046] I2C slave not started [0008.049] I2C write failed [0008.052] Writing offset failed [0008.055] eeprom_init: EEPROM read failed [0008.059] pm_ids_update: eeprom init failed [0008.063] pm_ids_update: Updating 3,a0, size 256, type 0 [0010.068] I2C transfer timeout [0010.071] I2C write failed [0010.074] Writing offset failed [0010.077] eeprom_init: EEPROM read failed [0010.081] pm_ids_update: eeprom init failed [0010.085] pm_ids_update: Updating 3,ae, size 256, type 0 [0012.090] I2C transfer timeout [0012.093] I2C write failed [0012.096] Writing offset failed [0012.099] eeprom_init: EEPROM read failed [0012.103] pm_ids_update: eeprom init failed [0014.107] I2C transfer timeout [0014.110] I2C write failed [0014.112] Writing offset failed [0014.115] eeprom_init: EEPROM read failed [0014.119] shim_get_serial_num:EEPROM read failed [0014.124] Reading Serial number from with NCT/FCT [0014.129] No serial number in NCT/EEPROM. Using fused IDs [0014.134] Chip UID is 00000001643206432400000006038300 [0014.139] Add serial number:00830306000000244306 as DT property [0014.147] Applying platform configs [0014.153] platform-init is not present. Skipping [0014.158] calling apps_init() [0014.179] Found 17 GPT partitions in "sdmmc3_user" [0014.184] Proceeding to Cold Boot [0014.187] starting app android_boot_app [0014.191] Device state: unlocked [0014.194] display console init [0014.202] could not find regulator [0014.225] hdmi cable not connected [0014.229] is_hdmi_needed: HDMI not connected, reDT entry for leds-pwm not found t[0014.239] urning false [0014.241] hdmi is not connected [0014.244] sor0 is not supported [0014.247] display_console_init: no valid display out_type [0014.255] subnode volume_up is not found ! [0014.259] subnode back is not found ! [0014.262] subnode volume_down is not found ! [0014.267] subnode menu is not found ! [0014.270] Gpio keyboard init success [0014.318] found decompressor handler: lz4-legacy [0014.332] decompressing blob (type 1)... [0014.398] display_resolution: No display init [0014.403] Failed to retrieve display resolution [0014.407] Could not load/initialize BMP blob...ignoring [0014.457] decompressor handler not found [0014.460] load_firmware_blob: Firmware blob loaded, entries=2 [0014.466] XUSB blob version 0 size 126464 @ 0x92cb328c [0014.472] -------> se_aes_verify_sbk_clear: 747 [0014.477] se_aes_verify_sbk_clear: Error [0014.480] SE operation failed [0014.483] bl_battery_charging: connected to external power supply [0014.492] display_console_ioctl: No display init [0014.497] switch_backlight failed [0014.506] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0014.514] MSC Partition not found [0014.523] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [0014.531] USP partition read failed! [0014.534] blob_init: blob-partition USP header read failed [0014.540] android_boot Unable to update recovery partition [0014.545] kfs_getpartname: name = LNX [0014.549] Loading kernel from LNX [0014.646] load kernel from storage [0014.655] decompressor handler not found [0014.689] Successfully loaded kernel and ramdisk images [0014.694] board ID = D78, board SKU = 2 [0014.699] display_resolution: No display init [0014.703] Failed to retrieve display resolution [0014.708] bmp blob is not loaded and initialized [0014.712] Failed to display boot-logo [0014.716] NCK carveout not present [0014.719] Skipping dts_overrides [0014.722] NCK carveout not present [0014.732] Find /i2c@7000c000's alias i2c0 [0014.735] get eeprom at 1-a0, size 256, type 0 [0014.744] Find /i2c@7000c500's alias i2c2 [0014.748] get eeprom at 3-a0, size 256, type 0 [0014.752] get eeprom at 3-ae, size 256, type 0 [0014.757] pm_ids_update: Updating 1,a0, size 256, type 0 [0014.762] I2C slave not started [0014.765] I2C write failed [0014.768] Writing offset failed [0014.771] eeprom_init: EEPROM read failed [0014.775] pm_ids_update: eeprom init failed [0014.779] pm_ids_update: Updating 3,a0, size 256, type 0 [0016.784] I2C transfer timeout [0016.787] I2C write failed [0016.790] Writing offset failed [0016.793] eeprom_init: EEPROM read failed [0016.797] pm_ids_update: eeprom init failed [0016.801] pm_ids_update: Updating 3,ae, size 256, type 0 [0018.806] I2C transfer timeout [0018.809] I2C write failed [0018.812] Writing offset failed [0018.815] eeprom_init: EEPROM read failed [0018.819] pm_ids_update: eeprom init failed [0020.823] I2C transfer timeout [0020.826] I2C write failed [0020.828] Writing offset failed [0020.831] eeprom_init: EEPROM read failed [0020.835] Plugin Manager: Parse ODM data 0x000a4000 [0020.847] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0020.855] Add serial number:00830306000000244306 as DT property [0020.864] "bpmp" doesn't exist, creating [0020.870] Updated bpmp info to DTB [0020.875] Updated initrd info to DTB [0020.878] "proc-board" doesn't exist, creating [0020.884] Updated board info to DTB [0020.887] "pmu-board" doesn't exist, creating [0020.893] Updated board info to DTB [0020.896] "display-board" doesn't exist, creating [0020.902] Updated board info to DTB [0020.905] "reset" doesn't exist, creating [0020.910] Updated reset info to DTB [0020.914] display_console_ioctl: No display init [0020.918] display_console_ioctl: No display init [0020.923] display_console_ioctl: No display init [0020.927] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt [0020.962] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0020.967] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [0020.984] Updated bootarg info to DTB [0020.987] Adding uuid 00000001643206432400000006038300 to DT [0020.993] Adding eks info 0 to DT [0020.998] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0021.004] Updated memory info to DTB [0021.009] add_lp0_disable: Unable to find plugin-manager ids under chosen node! (FDT_ERR_NOTFOUND) [0021.021] set vdd_core voltage to 1075 mv [0021.025] setting 'vdd-core' regulator to 1075000 micro volts [0021.031] Found secure-pmc; disable BPMP U-Boot 2020.04-g46e4604c78 (Jul 26 2021 - 12:09:42 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB tegra210_env_drv_config: find node offset error -1 MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from MMC... *** Warning - bad CRC, using default environment Loading Environment from SPI Flash... unrecognized JEDEC id bytes: 00, 00, 00 *** Warning - spi_flash_probe_bus_cs() failed, using default environment In: serial Out: serial Err: serial Can't find Ethernet MAC address in cboot DTB Net: No ethernet found. Hit any key to stop autoboot: 0 Card did not respond to voltage select! switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 879 bytes read in 30 ms (28.3 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7160133 bytes read in 179 ms (38.1 MiB/s) Retrieving file: /boot/Image 34691080 bytes read in 785 ms (42.1 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 0000000083178622 Can't find Ethernet MAC address in cboot DTB copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-tegra (root@ubuntu) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #31 SMP PREEMPT Fri Jan 28 12:44:22 MST 2022 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.058883] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.564606] Host read timeout at address 545c00c4 [ 1.574795] tegradc tegradc.1: dp: aux write got error (0x10000100) [ 1.574832] tegradc tegradc.1: dp: Failed for I2C write addr:80, size:1, stat:0x10000100 [ 1.587209] tegradc tegradc.1: dp: aux write got error (0x10000100) [ 1.587214] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100 [ 1.592225] tegradc tegradc.1: dp: aux write got error (0x10000100) [ 1.592229] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100 [ 1.597286] tegradc tegradc.1: dp: aux write got error (0x10000100) [ 1.597291] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100 [ 1.602109] tegradc tegradc.1: dp: aux write got error (0x10000100) [ 1.602113] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100 [ 1.602118] tegradc tegradc.1: dp: failed to exit panel power save mode (0xfffffff2) [ 1.715797] tegradc tegradc.1: dp: aux write got error (0x10000100) [ 1.722121] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100 [ 1.735202] tegradc tegradc.1: dp: aux write got error (0x10000100) [ 1.741523] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100 [ 1.754775] tegradc tegradc.1: dp: aux write got error (0x10000100) [ 1.761057] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100 [ 1.774354] tegradc tegradc.1: dp: aux write got error (0x10000100) [ 1.780630] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100 [ 1.788901] tegradc tegradc.1: dp: failed to exit panel power save mode (0xfffffff2) [ 1.796649] hpd: edid read prepare failed[ 2.866666] tegra-vii2c 546c0000.i2c: --- register dump for debugging ---- [ 2.873558] tegra-vii2c 546c0000.i2c: I2C_CNFG - 0x22c00 [ 2.878912] tegra-vii2c 546c0000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 2.885785] tegra-vii2c 546c0000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 2.891527] tegra-vii2c 546c0000.i2c: I2C_FIFO_STATUS - 0x800070 [ 2.897530] tegra-vii2c 546c0000.i2c: I2C_INT_MASK - 0xac [ 2.902925] tegra-vii2c 546c0000.i2c: I2C_INT_STATUS - 0x0 [ 2.908408] tegra-vii2c 546c0000.i2c: msg->len - 3 [ 2.913195] tegra-vii2c 546c0000.i2c: is_msg_write - 1 [ 2.918329] tegra-vii2c 546c0000.i2c: buf_remaining - 0 [ 2.923554] tegra-vii2c 546c0000.i2c: i2c transfer timed out, addr 0x0040, data 0x00 [ 2.931354] ina3221x 6-0040: ina3221 reset failure status: 0xffffff92 [ 2.969554] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): bad mac address at /chosen/nvidia,ethernet-mac: missing. [ 3.471576] cgroup: cgroup2: unknown option "nsdelegate" [ 4.762428] using random self ethernet address [ 4.778773] using random host ethernet address [ 5.163150] random: crng init done [ 5.166555] random: 7 urandom warning(s) missed due to ratelimiting [ 5.492764] using random self ethernet address [ 5.499140] using random host ethernet address [ 6.173449] gpio_bb: loading out-of-tree module taints kernel. [ 7.493683] Bridge firewalling registered