[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x50 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x317f6 [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.178] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.198] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.233] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.280] Initialize FailControl [0000.283] Read PT from (2:0) [0000.314] PT crc32 and magic check passed. [0000.318] Using BFS PT to query partitions [0000.323] Loading Tboot-CPU binary [0000.352] Verifying TBC in OdmNonSecureSBK mode [0000.362] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.369] Bootloader downloaded successfully. [0000.373] Downloaded Tboot-CPU binary to 0xa0000258 [0000.378] MAX77620_GPIO5 configured [0000.381] CPU power rail is up [0000.384] CPU clock enabled [0000.388] Performing RAM repair [0000.391] Updating A64 Warmreset Address to 0xa00002e9 [0000.396] BoardID = 3448, SKU = 0x0 [0000.399] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.403] Nano-SD: checking PT table on QSPI ... [0000.407] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.413] Loading NvTbootBootloaderDTB [0000.480] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.551] Bootloader DTB Load Address: 0x83000000 [0000.556] BoardID = 3448, SKU = 0x0 [0000.559] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.563] Nano-SD: checking PT table on QSPI ... [0000.567] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.573] Loading NvTbootKernelDTB [0000.639] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.711] Kernel DTB Load Address: 0x83100000 [0000.715] BoardID = 3448, SKU = 0x0 [0000.718] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.722] Nano-SD: checking PT table on QSPI ... [0000.726] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.734] Loading cboot binary [0000.850] Verifying EBT in OdmNonSecureSBK mode [0000.892] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.899] Bootloader downloaded successfully. [0000.903] BoardID = 3448, SKU = 0x0 [0000.906] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.910] Nano-SD: checking PT table on QSPI ... [0000.914] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.920] PT: Partition NCT NOT found ! [0000.924] Warning: Find Partition via PT Failed [0000.928] Next binary entry address: 0x92c00258 [0000.933] BoardId: 3448 [0000.938] Overriding pmu board id with proc board id [0000.942] Display board id is not available [0000.947] BoardID = 3448, SKU = 0x0 [0000.950] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.954] Nano-SD: checking PT table on QSPI ... [0000.958] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.065] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.121] /bpmp deleted [0001.123] SC7EntryFw header found loaded at 0xff700000 [0001.310] OVR2 PMIC [0001.312] Bpmp FW successfully loaded [0001.316] BoardID = 3448, SKU = 0x0 [0001.319] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.323] Nano-SD: checking PT table on QSPI ... [0001.327] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.334] WB0 init successfully at 0xff780000 [0001.338] Verifying NvTbootWb0 in OdmNonSecureSBK mode [0001.344] Set NvDecSticky Bits [0001.347] GSC2 address ff53fffc value c0edbbcc [0001.353] GSC MC Settings done [0001.356] BoardID = 3448, SKU = 0x0 [0001.360] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.363] Nano-SD: checking PT table on QSPI ... [0001.368] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.375] TOS Image length 53680 [0001.378] Monitor size 53680 [0001.381] OS size 0 [0001.396] Secure Os AES-CMAC Verification Success! [0001.400] TOS image cipher info: plaintext [0001.404] Loading and Validation of Secure OS Successful [0001.420] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.425] NvTbootPackSdramParams: start. [0001.430] NvTbootPackSdramParams: done. [0001.434] Tegraboot started after 51856 us [0001.438] Basic modules init took 935915 us [0001.442] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.447] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.453] Next stage binary read took 102860 us [0001.457] Carveout took -132464 us [0001.460] CPU initialization took 510356 us [0001.464] Total time taken by TegraBoot 1416667 us [0001.469] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:09:37, Jul 26 2021 ERROR: Error initializing runtime service trusty_fast [0001.591] RamCode = 0 [0001.596] LPDDR4 Training: Read DT: Number of tables = 2 [0001.601] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.614] EMC Training Successful [0001.617] 408000 not found in DVFS table [0001.623] RamCode = 0 [0001.626] DT Write: emc-table@204000 succeeded [0001.632] DT Write: emc-table@1600000 succeeded [0001.636] LPDDR4 Training: Write DT: Number of tables = 2 [0001.684] [0001.685] Debug Init done [0001.688] Marked DTB cacheable [0001.691] Bootloader DTB loaded at 0x83000000 [0001.696] Marked DTB cacheable [0001.699] Kernel DTB loaded at 0x83100000 [0001.702] DeviceTree Init done [0001.715] Pinmux applied successfully [0001.720] gicd_base: 0x50041000 [0001.723] gicc_base: 0x50042000 [0001.726] Interrupts Init done [0001.730] Using base:0x60005090 & irq:208 for tick-timer [0001.736] Using base:0x60005098 for delay-timer [0001.740] platform_init_timer: DONE [0001.743] Timer(tick) Init done [0001.747] osc freq = 38400 khz [0001.751] [0001.752] Welcome to L4T Cboot [0001.755] [0001.756] Cboot Version: 00.00.2018.01-t210-c952b4e6 [0001.761] calling constructors [0001.764] initializing heap [0001.767] initializing threads [0001.770] initializing timers [0001.773] creating bootstrap completion thread [0001.777] top of bootstrap2() [0001.780] CPU: ARM Cortex A57 [0001.783] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.788] initializing platform [0001.795] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.799] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.804] Macronix QSPI chip present [0001.807] SPI device register [0001.810] init boot device [0001.813] allocating memory for boot device(SPI) [0001.817] registering boot device [0001.836] QSPI bdev is already initialized [0001.840] Enable APE clock [0001.842] Un-powergate APE partition [0001.846] of_register: registering tegra_udc to of_hal [0001.851] of_register: registering inv20628-driver to of_hal [0001.857] of_register: registering ads1015-driver to of_hal [0001.862] of_register: registering lp8557-bl-driver to of_hal [0001.868] of_register: registering bq2419x_charger to of_hal [0001.873] of_register: registering bq27441_fuel_gauge to of_hal [0001.885] gpio framework initialized [0001.888] of_register: registering tca9539_gpio to of_hal [0001.894] of_register: registering tca9539_gpio to of_hal [0001.899] of_register: registering i2c_bus_driver to of_hal [0001.904] of_register: registering i2c_bus_driver to of_hal [0001.910] of_register: registering i2c_bus_driver to of_hal [0001.916] pmic framework initialized [0001.919] of_register: registering max77620_pmic to of_hal [0001.925] regulator framework initialized [0001.928] of_register: registering tps65132_bl_driver to of_hal [0001.934] initializing target [0001.940] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.948] board ID = D78, board SKU = 0 [0001.952] Skipping Z3! [0001.957] fixed regulator driver initialized [0001.974] initializing OF layer [0001.977] NCK carveout not present [0001.980] Skipping dts_overrides [0001.984] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.001] I2C Bus Init done [0002.003] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.014] I2C Bus Init done [0002.016] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.026] I2C Bus Init done [0002.029] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.039] I2C Bus Init done [0002.042] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.052] I2C Bus Init done [0002.055] of_children_init: Ops found for compatible string maxim,max77620 [0002.065] max77620_init using irq 118 [0002.070] register 'maxim,max77620' pmic [0002.074] gpio_driver_register: register 'max77620-gpio' driver [0002.080] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.091] I2C Bus Init done [0002.094] NCK carveout not present [0002.104] Find /i2c@7000c000's alias i2c0 [0002.108] get eeprom at 1-a0, size 256, type 0 [0002.116] Find /i2c@7000c500's alias i2c2 [0002.120] get eeprom at 3-a0, size 256, type 0 [0002.124] get eeprom at 3-ae, size 256, type 0 [0002.129] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.140] eeprom_init: EEPROM incompatible version found [0002.146] pm_ids_update: eeprom init failed [0002.150] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.180] pm_ids_update: The pm board id is 3448-0000-400 [0002.187] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.195] pm_ids_update: pm id update successful [0002.199] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.230] pm_ids_update: The pm board id is 3449-0000-400 [0002.236] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.244] pm_ids_update: pm id update successful [0002.274] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.280] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.288] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.294] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.302] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:a1:78 [0002.308] Plugin Manager: Parse ODM data 0x000a4000 [0002.320] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.335] Find /i2c@7000c000's alias i2c0 [0002.339] get eeprom at 1-a0, size 256, type 0 [0002.347] Find /i2c@7000c500's alias i2c2 [0002.351] get eeprom at 3-a0, size 256, type 0 [0002.356] get eeprom at 3-ae, size 256, type 0 [0002.360] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.372] eeprom_init: EEPROM incompatible version found [0002.377] pm_ids_update: eeprom init failed [0002.381] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.411] pm_ids_update: The pm board id is 3448-0000-400 [0002.417] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.424] pm_ids_update: pm id update successful [0002.429] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.459] pm_ids_update: The pm board id is 3449-0000-400 [0002.465] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.472] pm_ids_update: pm id update successful [0002.502] Add serial number:1424220032136 as DT property [0002.510] Applying platform configs [0002.516] platform-init is not present. Skipping [0002.521] calling apps_init() [0002.527] Couldn't find GPT header [0002.531] Proceeding to Cold Boot [0002.534] starting app android_boot_app [0002.538] Device state: unlocked [0002.541] display console init [0002.549] could not find regulator [0002.573] hdmi cable not connected [0002.576] is_hdmi_needed: HDMI not connected, returning false [0002.582[0002.586] DT entry for leds-pwm not found ] hdmi is not connected [0002.592] sor0 is not supported [0002.595] display_console_init: no valid display out_type [0002.603] subnode volume_up is not found ! [0002.607] subnode back is not found ! [0002.610] subnode volume_down is not found ! [0002.615] subnode menu is not found ! [0002.618] Gpio keyboard init success [0002.699] found decompressor handler: lz4-legacy [0002.713] decompressing blob (type 1)... [0002.779] display_resolution: No display init [0002.783] Failed to retrieve display resolution [0002.788] Could not load/initialize BMP blob...ignoring [0002.864] decompressor handler not found [0002.868] load_firmware_blob: Firmware blob loaded, entries=2 [0002.874] XUSB blob version 0 size 126464 @ 0x92ca828c [0002.880] -------> se_aes_verify_sbk_clear: 747 [0002.884] se_aes_verify_sbk_clear: Error [0002.888] SE operation failed [0002.891] bl_battery_charging: connected to external power supply [0002.900] display_console_ioctl: No display init [0002.904] switch_backlight failed [0002.910] device_query_partition_size: failed to open partition spiflash0:MSC ! [0002.918] MSC Partition not found [0002.924] device_query_partition_size: failed to open partition spiflash0:USP ! [0002.931] USP partition read failed! [0002.935] blob_init: blob-partition USP header read failed [0002.940] android_boot Unable to update recovery partition [0002.946] kfs_getpartname: name = LNX [0002.949] Loading kernel from LNX [0002.959] Found 19 BFS partitions in "spiflash0" [0003.279] load kernel from storage [0003.284] decompressor handler not found [0003.550] Successfully loaded kernel and ramdisk images [0003.555] board ID = D78, board SKU = 0 [0003.560] sdmmc node status = okay [0003.563] sdcard instance = 0 [0003.566] sdmmc cd-inverted [0003.568] sdcard gpio handle 0x5b [0003.572] sdcard gpio pin 0xc9 [0003.575] sdcard gpio flags 0x0 [0003.578] vmmc-supply 0x9d [0003.580] cd_gpio_pin = 201 [0003.583] pin_state = 0 [0003.585] Found sdcard [0003.587] SD-card IS present ... [0003.591] load_and_boot_kernel: SD card detected OK [0003.596] display_resolution: No display init [0003.601] Failed to retrieve display resolution [0003.605] bmp blob is not loaded and initialized [0003.610] Failed to display boot-logo [0003.613] NCK carveout not present [0003.616] Skipping dts_overrides [0003.620] NCK carveout not present [0003.629] Find /i2c@7000c000's alias i2c0 [0003.633] get eeprom at 1-a0, size 256, type 0 [0003.642] Find /i2c@7000c500's alias i2c2 [0003.645] get eeprom at 3-a0, size 256, type 0 [0003.650] get eeprom at 3-ae, size 256, type 0 [0003.654] pm_ids_update: Updating 1,a0, size 256, type 0 [0003.666] eeprom_init: EEPROM incompatible version found [0003.671] pm_ids_update: eeprom init failed [0003.675] pm_ids_update: Updating 3,a0, size 256, type 0 [0003.705] pm_ids_update: The pm board id is 3448-0000-400 [0003.712] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0003.720] pm_ids_update: pm id update successful [0003.725] pm_ids_update: Updating 3,ae, size 256, type 0 [0003.755] pm_ids_update: The pm board id is 3449-0000-400 [0003.761] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0003.769] pm_ids_update: pm id update successful [0003.799] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.805] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0003.813] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.819] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0003.827] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:a1:78 [0003.834] Plugin Manager: Parse ODM data 0x000a4000 [0003.846] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0003.854] Add serial number:1424220032136 as DT property [0003.863] "bpmp" doesn't exist, creating [0003.869] Updated bpmp info to DTB [0003.873] Updated initrd info to DTB [0003.877] "proc-board" doesn't exist, creating [0003.883] Updated board info to DTB [0003.886] "pmu-board" doesn't exist, creating [0003.892] Updated board info to DTB [0003.896] "display-board" doesn't exist, creating [0003.902] Updated board info to DTB [0003.905] "reset" doesn't exist, creating [0003.910] Updated reset info to DTB [0003.913] display_console_ioctl: No display init [0003.917] display_console_ioctl: No display init [0003.922] display_console_ioctl: No display init [0003.927] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt [0003.961] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0003.967] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0003.980] Updated bootarg info to DTB [0003.984] Adding uuid 000000016450b7011c00000012fd80c0 to DT [0003.990] Adding eks info 0 to DT [0003.995] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.001] Updated memory info to DTB [0004.009] set vdd_core voltage to 1125 mv [0004.012] setting 'vdd-core' regulator to 1125000 micro volts [0004.018] Found secure-pmc; disable BPMP U-Boot 2020.04-g46e4604c78 (Jul 26 2021 - 12:09:42 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 899 bytes read in 21 ms (41 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 5487776 bytes read in 259 ms (20.2 MiB/s) Retrieving file: /boot/Image 34277384 bytes read in 1499 ms (21.8 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 Retrieving file: /boot/tegra210-p3448-0000-p3449-0000-a02.dtb 241222 bytes read in 42 ms (5.5 MiB/s) ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083000000, end 000000008303de45 copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... DT property /chosen/nvidia,bluetooth-mac missing in source; can't copy DT property /chosen/nvidia,wifi-mac missing in source; can't copy DT property /psci/nvidia,system-lp0-disable missing in source; can't copy Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140 (admin@vm97) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Thu Jun 23 08:45:53 IST 2022 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.015313] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.521371] Host read timeout at address 545c00c4 [ 1.749597] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.757153] imx219 7-0010: board setup failed [ 1.785522] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.793058] imx219 8-0010: board setup failed [ 2.085034] mmc0: Data CRC error [ 2.088265] sdhci: =========== REGISTER DUMP (mmc0)=========== [ 2.094093] sdhci: Sys addr: 0x00000000 | Version: 0x00000303 [ 2.099920] sdhci: Blk size: 0x00007040 | Blk cnt: 0x00000000 [ 2.105747] sdhci: Argument: 0x80fffff3 | Trn mode: 0x00000013 [ 2.111575] sdhci: Present: 0x01fb0000 | Host ctl: 0x00000013 [ 2.117402] sdhci: Power: 0x00000001 | Blk gap: 0x00000000 [ 2.123228] sdhci: Wake-up: 0x00000000 | Clock: 0x00000407 [ 2.129054] sdhci: Timeout: 0x0000000e | Int stat: 0x00000000 [ 2.134881] sdhci: Int enab: 0x02ff100b | Sig enab: 0x02fc100b [ 2.140708] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 [ 2.146535] sdhci: Caps: 0x376cd08c | Caps_1: 0x10006f77 [ 2.152362] sdhci: Cmd: 0x0000063a | Max curr: 0x00000000 [ 2.158185] sdhci: Host ctl2: 0x00003008 [ 2.162108] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000ffefe410 [ 2.168683] sdhci: =========================================== [ 2.174672] mmc0: error -84 whilst initialising SD card [ 3.737215] mmc0: Data CRC error [ 3.740447] sdhci: =========== REGISTER DUMP (mmc0)=========== [ 3.746273] sdhci: Sys addr: 0x00000008 | Version: 0x00000303 [ 3.752098] sdhci: Blk size: 0x00007200 | Blk cnt: 0x00000006 [ 3.757923] sdhci: Argument: 0x00816e10 | Trn mode: 0x0000002b [ 3.763748] sdhci: Present: 0x01fb0000 | Host ctl: 0x00000013 [ 3.769574] sdhci: Power: 0x00000001 | Blk gap: 0x00000000 [ 3.775400] sdhci: Wake-up: 0x00000000 | Clock: 0x00000007 [ 3.781225] sdhci: Timeout: 0x0000000e | Int stat: 0x00000000 [ 3.787050] sdhci: Int enab: 0x02ff100b | Sig enab: 0x02fc100b [ 3.792876] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 [ 3.798700] sdhci: Caps: 0x376cd08c | Caps_1: 0x10006f77 [ 3.804525] sdhci: Cmd: 0x0000193a | Max curr: 0x00000000 [ 3.810347] sdhci: Host ctl2: 0x00003000 [ 3.814267] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000ffefe410 [ 3.820836] sdhci: =========================================== [ 3.827960] mmcblk0: error -84 transferring data, sector 8482320, nr 8, cmd response 0x900, card status 0xc00 [ 3.921338] mmc0: Data CRC error [ 3.924561] sdhci: =========== REGISTER DUMP (mmc0)=========== [ 3.930387] sdhci: Sys addr: 0x00000006 | Version: 0x00000303 [ 3.936214] sdhci: Blk size: 0x00007200 | Blk cnt: 0x00000005 [ 3.942039] sdhci: Argument: 0x00816e12 | Trn mode: 0x0000002b [ 3.947864] sdhci: Present: 0x01fb0000 | Host ctl: 0x00000013 [ 3.953689] sdhci: Power: 0x00000001 | Blk gap: 0x00000000 [ 3.959514] sdhci: Wake-up: 0x00000000 | Clock: 0x00000007 [ 3.965339] sdhci: Timeout: 0x0000000e | Int stat: 0x00000000 [ 3.971164] sdhci: Int enab: 0x02ff100b | Sig enab: 0x02fc100b [ 3.976989] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 [ 3.982815] sdhci: Caps: 0x376cd08c | Caps_1: 0x10006f77 [ 3.988640] sdhci: Cmd: 0x0000193a | Max curr: 0x00000000 [ 3.994463] sdhci: Host ctl2: 0x00003000 [ 3.998383] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000ffefe410 [ 4.004954] sdhci: =========================================== [ 4.012439] mmcblk0: error -84 transferring data, sector 8482322, nr 6, cmd response 0x900, card status 0xc00 [ 4.023270] blk_update_request: I/O error, dev mmcblk0, sector 8482323 [ 4.029801] Buffer I/O error on dev mmcblk0p1, logical block 1056706, lost async page write [ 4.041130] mmc0: Data CRC error [ 4.044354] sdhci: =========== REGISTER DUMP (mmc0)=========== [ 4.050180] sdhci: Sys addr: 0x00000008 | Version: 0x00000303 [ 4.056006] sdhci: Blk size: 0x00007200 | Blk cnt: 0x00000004 [ 4.061831] sdhci: Argument: 0x00c48838 | Trn mode: 0x0000002b [ 4.067658] sdhci: Present: 0x01fb0000 | Host ctl: 0x00000013 [ 4.073484] sdhci: Power: 0x00000001 | Blk gap: 0x00000000 [ 4.079310] sdhci: Wake-up: 0x00000000 | Clock: 0x00000007 [ 4.085135] sdhci: Timeout: 0x0000000e | Int stat: 0x00000000 [ 4.090960] sdhci: Int enab: 0x02ff100b | Sig enab: 0x02fc100b [ 4.096785] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 [ 4.102611] sdhci: Caps: 0x376cd08c | Caps_1: 0x10006f77 [ 4.108435] sdhci: Cmd: 0x0000193a | Max curr: 0x00000000 [ 4.114257] sdhci: Host ctl2: 0x00003000 [ 4.118178] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000ffefe410 [ 4.124748] sdhci: =========================================== [ 4.131869] mmcblk0: error -84 transferring data, sector 12879928, nr 8, cmd response 0x900, card status 0xc00 [ 4.142406] blk_update_request: I/O error, dev mmcblk0, sector 12879932 [ 4.149023] Buffer I/O error on dev mmcblk0p1, logical block 1606407, lost async page write [ 4.159477] mmc0: Data CRC error [ 4.162702] sdhci: =========== REGISTER DUMP (mmc0)=========== [ 4.168528] sdhci: Sys addr: 0x00000020 | Version: 0x00000303 [ 4.174353] sdhci: Blk size: 0x00007200 | Blk cnt: 0x0000001f [ 4.180179] sdhci: Argument: 0x00007000 | Trn mode: 0x0000002b [ 4.186005] sdhci: Present: 0x01fb0000 | Host ctl: 0x00000013 [ 4.191831] sdhci: Power: 0x00000001 | Blk gap: 0x00000000 [ 4.197656] sdhci: Wake-up: 0x00000000 | Clock: 0x00000007 [ 4.203482] sdhci: Timeout: 0x0000000e | Int stat: 0x00000000 [ 4.209306] sdhci: Int enab: 0x02ff100b | Sig enab: 0x02fc100b [ 4.215131] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 [ 4.220955] sdhci: Caps: 0x376cd08c | Caps_1: 0x10006f77 [ 4.226779] sdhci: Cmd: 0x0000193a | Max curr: 0x00000000 [ 4.232602] sdhci: Host ctl2: 0x00003000 [ 4.236522] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000ffefe410 [ 4.243091] sdhci: =========================================== [ 4.250087] mmcblk0: error -84 transferring data, sector 28672, nr 32, cmd response 0x900, card status 0xc00 [ 4.260443] blk_update_request: I/O error, dev mmcblk0, sector 28673 [ 4.266818] Buffer I/O error on dev mmcblk0p1, logical block 0, lost async page write [ 4.274664] blk_update_request: I/O error, dev mmcblk0, sector 28680 [ 4.281016] Buffer I/O error on dev mmcblk0p1, logical block 1, lost async page write [ 4.288851] blk_update_request: I/O error, dev mmcblk0, sector 28688 [ 4.295199] Buffer I/O error on dev mmcblk0p1, logical block 2, lost async page write [ 4.303027] blk_update_request: I/O error, dev mmcblk0, sector 28696 [ 4.309376] Buffer I/O error on dev mmcblk0p1, logical block 3, lost async page write [ 4.344621] EXT4-fs (mmcblk0p1): error loading journal