▒▒
[0000.064] I> MB1 (version: 0.11.0.0-t234-54845784-7fb1fa27)
[0000.069] I> t234-A01-0-Silicon (0x12347) Prod
[0000.073] I> Boot-mode : Coldboot
[0000.076] I> Emulation:
[0000.079] I> Entry timestamp: 0x00000000
[0000.083] I> last_boot_error: 0x0
[0000.086] I> BR-BCT: preprod_dev_sign: 0
[0000.089] I> rst_source: 0x0, rst_level: 0x0
[0000.094] I> Task: Clocks enable (0x50011b9d)
[0000.098] I> Task: Crypto init (0x50018df5)
[0000.102] I> Task: Secure debug controls (0x5000c76d)
[0000.107] E> Error: ECID of check failed!!
[0000.111] E> Error: ECID of check failed!!
[0000.115] E> Error: ECID of check failed!!
[0000.119] E> Error: ECID of check failed!!
[0000.123] I> Task: Program NV master stream id (0x5000c725)
[0000.128] I> Task: Verify boot mode (0xd482021)
[0000.136] I> Task: Alias fuses (0x5000ecd5)
[0000.141] E> FUSE_ALIAS: Fuse alias on production fused part is not supported.
[0000.148] I> Task: 0x5000e911
[0000.151] I> FUSE_OPT_CCPLEX_CLUSTER_DISABLE = 0x00000000
[0000.156] I> FUSE_OPT_GPC_DISABLE = 0x00000000
[0000.160] I> FUSE_OPT_DLA_DISABLE = 0x00000000
[0000.165] I> FUSE_OPT_EMC_DISABLE = 0x00000000
[0000.169] I> FUSE_BOOTROM_PATCH_VERSION = 0x7
[0000.173] I> FUSE_PSCROM_PATCH_VERSION = 0x7
[0000.177] I> FUSE_OPT_ADC_CAL_FUSE_REV = 0x2
[0000.181] I> FUSE_SKU_INFO_0 = 0xd0
[0000.185] I> FUSE_OPT_SAMPLE_TYPE_0 = 0x3 PS
[0000.189] I> FUSE_PACKAGE_INFO_0 = 0x2
[0000.192] I> SKU: Perfect F0
[0000.195] I> Task: Voltage monitor (0x50011ba5)
[0000.199] I> VMON: Vmon re-calibration and fine tuning done
[0000.205] I> Task: Blockdev init (0x500157e1)
[0000.209] I> Task: UPHY init (0x5001b42d)
[0000.213] E> UPHY: UPHY lane info table is empty in MB1 BCT.
[0000.219] I> Task: Boot device init (0x5000d6a9)
[0000.223] E> Adding eMMC storage modules
[0000.227] I> Boot-device: QSPI (instance: 0)
[0000.231] I> qspi flash params source = mb1bct
[0000.236] I> Qspi clock source : pllc_out0
[0000.240] I> QSPI-0l initialized successfully
[0000.244] I> Task: TSC init (0x5001c7e1)
[0000.248] I> Task: Enable WDT 5th expiry (0x5001d27d)
[0000.253] I> Task: Disable WDT globally (0x5001d2b9)
[0000.258] I> Task: I2C register (0x50000a09)
[0000.262] I> Task: Reset FSI (0x50011ba1)
[0000.266] I> Task: Pinmux init (0x50010e95)
[0000.270] I> Task: Prod config init (0x50011075)
[0000.274] I> Task: Pad voltage init (0x50010f85)
[0000.279] I> Task: Prod init (0x50011119)
[0000.283] I> Task: Thermal check (0x5001121d)
[0000.287] I> max_chip_limit = 115
[0000.290] I> min_chip_limit = -30
[0000.303] I> max temp read = 51
[0000.306] I> min temp read = 47
[0000.309] I> Task: Common rail init (0x50011695)
[0000.314] W>  Thermal config not found in BCT
[0000.318] W>  Generic i2c config not found in BCT
[0000.323]  > DEVICE_PROD: module = 13, instance = 4 not found in device prod.
[0000.331] W>  MEMIO rail config not found in BCT
[0000.336] I> Task: Mem clock src (0x5000f6b9)
[0000.340] I> Task: BR PMIC seq (0x50011711)
[0000.344] I> Task: Misc. board config (0x500116ed)
[0000.348] W>  Platform config not found in BCT
[0000.353] I> Task: Load membct (0x5000f5d5)
[0000.357] I> RAM_CODE 0x4000401
[0000.360] I> Loading MEM-BCT to SysRAM
[0000.363] I> Scratch RSV109: 0x00000001    active chain: 0
[0000.369] I> Slot: 0
[0000.371] I> Binary[0] block-0 (partition size: 0x40000)
[0000.376] I>  get_binary_info: Binary name: MEM-BCT-0
[0000.381] I> Size of crypto header is 8192
[0000.385] I> BCH load address is : 0x40050000
[0000.389] I> Size of crypto header is 8192
[0000.393] I> BCH of MEM-BCT-0 read from storage
[0000.397] I> BCH address is : 0x40050000
[0000.401] I> MEM-BCT-0 header integrity check is success
[0000.406] I> Binary magic in BCH component 0 is MEM0
[0000.411] I> component binary type is 0
[0000.415] I> MEM-BCT-0 binary is read from storage
[0000.420] I> MEM-BCT-0 binary integrity check is success
[0000.425] I> Binary MEM-BCT-0 loaded successfully at 0x40040000 (0xe580)
[0000.436] I> RAM_CODE 0x4000401
[0000.440] I> Task: Save mem-bct info (0x50011d59)
[0000.444] I> Task: SDRAM params override (0x50010c79)
[0000.449] I> Task: Carveout allocate (0x50011da5)
[0000.454] I> RCM blob carveout will not be allocated
[0000.459] I> ECC region[0]: Start:0x0, End:0x0
[0000.463] I> ECC region[1]: Start:0x0, End:0x0
[0000.467] I> ECC region[2]: Start:0x0, End:0x0
[0000.471] I> ECC region[3]: Start:0x0, End:0x0
[0000.476] I> ECC region[4]: Start:0x0, End:0x0
[0000.480] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000
[0000.486] I> Non-ECC region[1]: Start:0x0, End:0x0
[0000.490] I> Non-ECC region[2]: Start:0x0, End:0x0
[0000.495] I> Non-ECC region[3]: Start:0x0, End:0x0
[0000.500] I> Non-ECC region[4]: Start:0x0, End:0x0
[0000.506] I> allocated(CO:51) base:0x80000000 size:0x8000000 align: 0x200000
[0000.513] I> allocated(CO:44) base:0xd6000000 size:0x2a000000 align: 0x100000
[0000.520] I> allocated(CO:31) base:0xce000000 size:0x8000000 align: 0x100000
[0000.527] I> allocated(CO:39) base:0xc8000000 size:0x6000000 align: 0x200000
[0000.534] I> allocated(CO:20) base:0xc6000000 size:0x2000000 align: 0x2000000
[0000.541] I> allocated(CO:24) base:0xc4000000 size:0x2000000 align: 0x2000000
[0000.548] I> allocated(CO:28) base:0xc2000000 size:0x2000000 align: 0x2000000
[0000.555] I> allocated(CO:29) base:0xc0000000 size:0x2000000 align: 0x2000000
[0000.562] I> allocated(CO:41) base:0xbf000000 size:0x1000000 align: 0x100000
[0000.569] I> allocated(CO:43) base:0xbe000000 size:0x1000000 align: 0x200000
[0000.576] I> allocated(CO:02) base:0xbd800000 size:0x800000 align: 0x800000
[0000.583] I> allocated(CO:03) base:0xbd000000 size:0x800000 align: 0x800000
[0000.590] I> allocated(CO:06) base:0xbc800000 size:0x800000 align: 0x800000
[0000.597] I> allocated(CO:10) base:0xbc000000 size:0x800000 align: 0x800000
[0000.603] I> allocated(CO:56) base:0xbb800000 size:0x800000 align: 0x200000
[0000.610] I> allocated(CO:07) base:0xbb400000 size:0x400000 align: 0x400000
[0000.617] I> allocated(CO:22) base:0xbb000000 size:0x400000 align: 0x400000
[0000.624] I> allocated(CO:33) base:0xbac00000 size:0x400000 align: 0x200000
[0000.631] I> allocated(CO:47) base:0xba800000 size:0x400000 align: 0x200000
[0000.638] I> allocated(CO:01) base:0xba700000 size:0x100000 align: 0x100000
[0000.644] I> allocated(CO:04) base:0xba600000 size:0x100000 align: 0x100000
[0000.651] I> allocated(CO:05) base:0xba500000 size:0x100000 align: 0x100000
[0000.658] I> allocated(CO:08) base:0xba400000 size:0x100000 align: 0x100000
[0000.665] I> allocated(CO:09) base:0xba300000 size:0x100000 align: 0x100000
[0000.672] I> allocated(CO:15) base:0xba200000 size:0x100000 align: 0x100000
[0000.679] I> allocated(CO:17) base:0xba100000 size:0x100000 align: 0x100000
[0000.685] I> allocated(CO:23) base:0xba000000 size:0x100000 align: 0x100000
[0000.692] I> allocated(CO:27) base:0xb9f00000 size:0x100000 align: 0x100000
[0000.699] I> allocated(CO:42) base:0xb9e00000 size:0x100000 align: 0x100000
[0000.706] I> allocated(CO:54) base:0xb9d80000 size:0x80000 align: 0x80000
[0000.713] I> allocated(CO:26) base:0xb9d40000 size:0x40000 align: 0x2000
[0000.719] I> allocated(CO:48) base:0xb9d20000 size:0x20000 align: 0x10000
[0000.726] I> allocated(CO:34) base:0xb9d10000 size:0x10000 align: 0x10000
[0000.732] I> allocated(CO:35) base:0xb9d00000 size:0x10000 align: 0x10000
[0000.739] I> allocated(CO:49) base:0xb9cf0000 size:0x10000 align: 0x10000
[0000.746] I> allocated(CO:50) base:0xb9ce0000 size:0x10000 align: 0x10000
[0000.752] I> allocated(CO:52) base:0xb9cd0000 size:0x10000 align: 0x10000
[0000.759] I> Task: SDRAM init (0x5000f6bd)
[0000.765] I> SDRAM-params @ 0xd485000
[0000.769] I> MSS code-drop: NvBootSdramInit
[0000.773] I> MSS CAR: PLLM/HUB programming for MemoryType: 4 and MemBctRevision: 8
[0000.780] I> MSS CAR: Init PLLM
[0000.783] I> MSS CAR: Init PLLHUB
[0000.794] I> mb1_sdram_init Done !
[0000.797] I> SDRAM Size in Total 800000000
[0000.801] I> SDRAM test pass
[0000.804] I> Task: Dram ecc scrub (0x5000f2c9)
[0000.808] I> Task: DRAM alias check (0x50010c71)
[0001.025] I> Task: Register checker (0x50010c75)
[0001.033] I> Task: Enable clock-mon (0x5001c301)
[0001.050] I> FMON: Fmon re-programmed in mb1
[0001.055] I> Task: Mapper init (0x5001a0d5)
[0001.060] I> Task: SC7 Context Init (0x5001cacd)
[0001.066] I> NV_SC7 Context addr: 0xa0000000
[0001.071] I> Task: CCPLEX IST init (0x5000ce75)
[0001.077] I> Task: CPU WP0 (0x5000c2c9)
[0001.082] I> Loading MCE
[0001.085] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.091] I> Slot: 0
[0001.093] I> Binary[8] block-0 (partition size: 0x80000)
[0001.099] I>  get_binary_info: Binary name: MCE
[0001.104] I> Size of crypto header is 8192
[0001.109] I> BCH load address is : 0x4003e000
[0001.114] I> Size of crypto header is 8192
[0001.119] I> BCH of MCE read from storage
[0001.123] I> BCH address is : 0x4003e000
[0001.129] I> MCE header integrity check is success
[0001.134] I> Binary magic in BCH component 0 is MTSM
[0001.139] I> component binary type is 8
[0001.143] I> Size of crypto header is 8192
[0001.150] I> MCE binary is read from storage
[0001.155] I> MCE binary integrity check is success
[0001.160] I> Binary MCE loaded successfully at 0x40000000 (0x29e90)
[0001.168] I> Size of crypto header is 8192
[0001.180] I> Size of crypto header is 8192
[0001.184] I> Sending WP0 mailbox command to PSC
[0001.197] I> Task: MB1 fixed firewalls (0x5001b1bd)
[0001.209] I> Task: Load bpmp-fw (0x5001b311)
[0001.214] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.220] I> Slot: 0
[0001.222] I> Binary[15] block-0 (partition size: 0x100000)
[0001.229] I>  get_binary_info: Binary name: BPMP_FW
[0001.234] I> Size of crypto header is 8192
[0001.238] I> BCH load address is : 0x807fe000
[0001.244] I> Size of crypto header is 8192
[0001.249] I> BCH of BPMP_FW read from storage
[0001.253] I> BCH address is : 0x807fe000
[0001.259] I> BPMP_FW header integrity check is success
[0001.264] I> Binary magic in BCH component 0 is BPMF
[0001.270] I> component binary type is 15
[0001.274] I> Size of crypto header is 8192
[0001.289] I> BPMP_FW binary is read from storage
[0001.296] I> BPMP_FW binary integrity check is success
[0001.301] I> Binary BPMP_FW loaded successfully at 0x80000000 (0xf3940)
[0001.310] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.316] I> Slot: 0
[0001.318] I> Binary[16] block-0 (partition size: 0x100000)
[0001.324] I>  get_binary_info: Binary name: BPMP_FW_DTB
[0001.330] I> Size of crypto header is 8192
[0001.334] I> BCH load address is : 0x807fc000
[0001.340] I> Size of crypto header is 8192
[0001.345] I> BCH of BPMP_FW_DTB read from storage
[0001.350] I> BCH address is : 0x807fc000
[0001.355] I> BPMP_FW_DTB header integrity check is success
[0001.361] I> Binary magic in BCH component 0 is BPMD
[0001.366] I> component binary type is 16
[0001.371] I> Size of crypto header is 8192
[0001.377] I> BPMP_FW_DTB binary is read from storage
[0001.383] I> BPMP_FW_DTB binary integrity check is success
[0001.389] I> Binary BPMP_FW_DTB loaded successfully at 0x807dbc00 (0x20380)
[0001.397] I> Program IPC carveouts
[0001.403] I> Task: Load psc-fw (0x5001b3b9)
[0001.408] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.414] I> Slot: 0
[0001.417] I> Binary[17] block-0 (partition size: 0x80000)
[0001.423] I>  get_binary_info: Binary name: PSC_FW
[0001.428] I> Size of crypto header is 8192
[0001.432] I> BCH load address is : 0x803fe000
[0001.438] I> Size of crypto header is 8192
[0001.443] I> BCH of PSC_FW read from storage
[0001.447] I> BCH address is : 0x803fe000
[0001.453] I> PSC_FW header integrity check is success
[0001.458] I> Binary magic in BCH component 0 is PFWP
[0001.464] I> component binary type is 17
[0001.468] I> Size of crypto header is 8192
[0001.476] I> PSC_FW binary is read from storage
[0001.482] I> PSC_FW binary integrity check is success
[0001.488] I> Binary PSC_FW loaded successfully at 0x80000000 (0x57800)
[0001.496] I> Task: Load nvdec-fw (0x5001c05d)
[0001.502] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.507] I> Slot: 0
[0001.510] I> Binary[7] block-0 (partition size: 0x100000)
[0001.516] I>  get_binary_info: Binary name: NVDEC
[0001.521] I> Size of crypto header is 8192
[0001.526] I> BCH load address is : 0x800fe000
[0001.531] I> Size of crypto header is 8192
[0001.536] I> BCH of NVDEC read from storage
[0001.540] I> BCH address is : 0x800fe000
[0001.546] I> NVDEC header integrity check is success
[0001.551] I> Binary magic in BCH component 0 is NDEC
[0001.557] I> component binary type is 7
[0001.561] I> Size of crypto header is 8192
[0001.568] I> NVDEC binary is read from storage
[0001.573] I> NVDEC binary integrity check is success
[0001.579] I> Binary NVDEC loaded successfully at 0x80000000 (0x35000)
[0001.591] I> Task: Load tsec-fw (0x5001c249)
[0001.596] I> TSEC-FW load support not enabled
[0001.601] I> Task: TZDRAM setup (0x50012515)
[0001.606] I> Task: SC7 context save (0x5001cbd1)
[0001.612] I> NV_SC7 Context addr: 0xa0000000
[0001.618] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.624] I> Slot: 0
[0001.626] I> Binary[13] block-0 (partition size: 0x20000)
[0001.632] I>  get_binary_info: Binary name: SC7-FW
[0001.637] I> Size of crypto header is 8192
[0001.642] I> Size of crypto header is 8192
[0001.647] I> BCH load address is : 0xa0002000
[0001.652] I> Size of crypto header is 8192
[0001.657] I> BCH of SC7-FW read from storage
[0001.661] I> BCH address is : 0xa0002000
[0001.667] I> SC7-FW header integrity check is success
[0001.672] I> Binary magic in BCH component 0 is WB0B
[0001.678] I> component binary type is 13
[0001.682] I> Size of crypto header is 8192
[0001.687] I> SC7-FW binary is read from storage
[0001.693] I> SC7-FW binary integrity check is success
[0001.698] I> Binary SC7-FW loaded successfully at 0xa0004000 (0xa4e0)
[0001.706] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.712] I> Slot: 0
[0001.714] I> Binary[22] block-0 (partition size: 0x30000)
[0001.720] I>  get_binary_info: Binary name: PSC_RF
[0001.726] I> Size of crypto header is 8192
[0001.730] I> Size of crypto header is 8192
[0001.735] I> BCH load address is : 0xa000e4e0
[0001.740] I> Size of crypto header is 8192
[0001.745] I> BCH of PSC_RF read from storage
[0001.750] I> BCH address is : 0xa000e4e0
[0001.755] I> PSC_RF header integrity check is success
[0001.761] I> Binary magic in BCH component 0 is PSCR
[0001.766] I> component binary type is 22
[0001.770] I> Size of crypto header is 8192
[0001.776] I> PSC_RF binary is read from storage
[0001.782] I> PSC_RF binary integrity check is success
[0001.787] I> Binary PSC_RF loaded successfully at 0xa00104e0 (0x1af70)
[0001.806] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.812] I> Slot: 0
[0001.814] I> Binary[14] block-0 (partition size: 0x20000)
[0001.820] I>  get_binary_info: Binary name: MB2_RF
[0001.825] I> Size of crypto header is 8192
[0001.830] I> Size of crypto header is 8192
[0001.835] I> BCH load address is : 0xa008c020
[0001.840] I> Size of crypto header is 8192
[0001.845] I> BCH of MB2_RF read from storage
[0001.849] I> BCH address is : 0xa008c020
[0001.855] I> MB2_RF header integrity check is success
[0001.861] I> Binary magic in BCH component 0 is MB2R
[0001.866] I> component binary type is 14
[0001.870] I> Size of crypto header is 8192
[0001.875] I> MB2_RF binary is read from storage
[0001.881] I> MB2_RF binary integrity check is success
[0001.886] I> Binary MB2_RF loaded successfully at 0xa008e020 (0xd360)
[0001.895] E> FUSE_ALIAS: Fuse alias on production fused part is not supported.
[0001.903] I> SC7 context fuse-bypass data is empty
[0001.908] I> SC7 context save done
[0001.912] I> Task: Load MB2/Applet/FSKP (0x5001c305)
[0001.918] I> Loading MB2
[0001.921] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.927] I> Slot: 0
[0001.929] I> Binary[6] block-0 (partition size: 0x70000)
[0001.935] I>  get_binary_info: Binary name: MB2
[0001.940] I> Size of crypto header is 8192
[0001.944] I> BCH load address is : 0x8007e000
[0001.950] I> Size of crypto header is 8192
[0001.955] I> BCH of MB2 read from storage
[0001.959] I> BCH address is : 0x8007e000
[0001.965] I> MB2 header integrity check is success
[0001.970] I> Binary magic in BCH component 0 is MB2B
[0001.975] I> component binary type is 6
[0001.979] I> Size of crypto header is 8192
[0001.988] I> MB2 binary is read from storage
[0001.994] I> MB2 binary integrity check is success
[0001.999] I> Binary MB2 loaded successfully at 0x80000000 (0x69940)
[0002.007] I> Task: Prepare MB2 params (0x5001c3d5)
[0002.015] I> MB2-params @ 0x40060000
[0002.022] I> BR-BCT Boot Chain Fields
[0002.026] I>    u32_non_gpio_select_boot_chain  : 0
[0002.031] I>    u32_num_boot_chains             : 2
[0002.036] I>    bf_bl_gpio_select_boot_chain_1b : 0
[0002.041] I> Task: Dram ecc test (0x5000f379)
[0002.047] I> Task: Misc NV security settings (0x5000ca35)
[0002.053] I> NVDEC sticky bits programming done
[0002.058] I> Task: GPIO interrupt map (0x50011a61)
[0002.064] I> Task: Disable/Reload WDT (0x5001d2e9)
[0002.070] I> Programmed SLCG global override := 0x0
[0002.076] I> MB1: MSS reconfig completed
I> MB2 (version: 0.0.0.0-t234-54845784-d4c4cf0d)
I> t234-A01-0-Silicon (0x12347)
I> Boot-mode : Coldboot
I> Emulation:
I> Entry timestamp: 0x0020543f
I> Regular heap: [base:0x40040000, size:0x10000]
I> DMA heap: [base:0xbb800000, size:0x800000]
I> Task: Enable hot-plug capability (0x5001aee8)
I> Task: Set blob address (0x50001c70)
I> Task: PSC mailbox init (0x5000e5e0)
I> Task: Crypto init (0x50005abc)
I> Task: I2C register (0x50001c5c)
I> Task: Boot device init (0x50001d2c)
I> Boot_device: QSPI_FLASH instance: 0
I> Qspi clock source : pllc_out0
I> QSPI-0l initialized successfully
I> qspi flash-0 params source = MB2 params
I> sdmmc-3 params source = MB2 params
I> Task: Partition Manager Init (0x50001cf8)
I> Found 57 partitions in QSPI_FLASH (instance 0)
W> Cannot find any partition table for 00000003
 > PARTITION_MANAGER: Failed to publish partition.
I> Found 11 partitions in SDMMC_USER (instance 3)
I> Task: Load and authenticate registered FWs (0x50012828)
I> Task: Load AUXP FWs (0x5001aa8c)
I> Successfully register SPE FW load task with MB2 loader
I> Skipping SCE FW load
I> Successfully register RCE FW load task with MB2 loader
I> Successfully register DCE FW load task with MB2 loader
I> Unpowergating APE
I> Unpowergate done
I> Successfully register APE FW load task with MB2 loader
I> Skipping FSI FW load
I> Successfully register XUSB FW load task with MB2 loader
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_spe-fw
I> Size of partition: 589824
I> Binary@ device:3/0 block-56320 (partition size: 0x90000), name: A_spe-fw
E> Binary spe is not found in comp table
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_rce-fw
I> Size of partition: 1048576
I> Binary@ device:3/0 block-57472 (partition size: 0x100000), name: A_rce-fw
E> Binary rce is not found in comp table
I> spe: Authentication Finalize Done
I> Binary spe loaded successfully at 0xba400000
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_dce-fw
I> Size of partition: 9437184
I> Binary@ device:3/0 block-37888 (partition size: 0x900000), name: A_dce-fw
E> Binary dce is not found in comp table
I> rce: Authentication Finalize Done
I> Binary rce loaded successfully at 0xba100000
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_adsp-fw
I> Size of partition: 2097152
I> Binary@ device:3/0 block-59520 (partition size: 0x200000), name: A_adsp-fw
E> Binary ape is not found in comp table
I> dce: Authentication Finalize Done
I> Binary dce loaded successfully at 0xc6000000
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_xusb-fw
I> Size of partition: 262144
I> Binary@ device:3/0 block-10368 (partition size: 0x40000), name: A_xusb-fw
E> Binary xusb is not found in comp table
I> ape: Authentication Finalize Done
I> Binary ape loaded successfully at 0xbb400000
I> xusb: Authentication Finalize Done
I> Binary xusb loaded successfully at 0xba500000
I> Task: Carveout setup (0x50014028)
I> Program remaining OEM carveouts
I> Task: Restore XUSB sec (0x50001c30)
I> Task: OEM firewalls (0x50017ef0)
I> MB2-BCT Firewall data is empty
I> Task: Unhalt AUXPs (0x5001acf4)
I> Unhalting SPE..
I> Enabling combined UART
▒▒▒▒spe: early_init
vic initialized
tsc initialized
aon lic initialized
spe: tag is 9f1f07bc2d4b6509c13554672acefaad
spe: SafeRTOS v8.4
spe: init
scheduler initialized
aon hsp initialized
tag initialized
tcu initialized
bpmp ipc initialized
spe: late init
cpu_nic clock initialized
apb clock initialized
pm initialized
bpmp hsp initialized
top1 hsp initialized
ccplex ipc initialized
spe: start scheduler
▒▒
  I> Task: Trigger mailbox for PSC-BL1 exit (0x5000e660)
I> Sending opcode 0x4d420802 to psc
▒▒INFO: Entering psc_monitor_init!
INFO: GSC22 BOM:0xbb000000 SIZE:0x400000 CLIENT_ACCESS1:00180000
INFO: PSCFW BUILD VERSION: a796142-39d6527-7490c54-dev
INFO: mstatus:0xa00000808
INFO: Supervisor entry_point:c108c00
INFO: pllpsc▒▒I> Received ACK from psc
I> Task: Start secure NOR provision (0x50010b▒▒
                                               ▒▒ is already locked.
INFO: MONITOR: user task addr:0xbb022000, blob offset:▒▒50)
I> Task: Load FSI keyblob (0x5000ea28)
I> Skipping FSI key blob copy
I> Task: Enable FSITHERM (0x5000e5b4)
▒▒0x00020000
▒▒I> Task: Unhalt AUXPs (0x5001acfc)
I> SCE unhalt skipped
I> Unhalting RCE
I> RCE unhalt successful
I> DCE unhalt successful
I> APE unhalt skipped
I> FSI unhalt skipped
I> Task: Load CPUBL (0x5000f7d8)
I> Task: Load TOS (0x5000fe64)
I> ▒▒bpmp: init
bpmp: bas▒▒Task: Load and authenticate registered FWs (0x50012828)
I> Scratch RSV109: 0x▒▒[     2.454700] Camera-FW on t234-rce-safe started
▒▒INFO: MONITOR: populated▒▒
                            ▒▒00000001    active chain: 0
▒▒TCU early console ena▒▒e binary md5 is f0425▒▒ user images:16
INFO: mret to Supervisor!
INFO: psc supervisor init.
INFO: ▒▒a554b39d571b1bbb5291283d946
bpmp: combined binary md5 is 43f75b5aad2b8e1992e4e049bafc8696
bpmp: firmware tag is 43f75b5aad2b8e1992e4-f0425a554b3
initialized vwdt
initialized clk_mach_early
initialized mail_earl▒▒I> Partition name: A_▒▒bled.
▒▒cpu-bootloader
I> Size of partition: 3670016
I> Binary@ device:3/0 block-17920 (partition size: 0x380000), name: A_cpu-bootloader
▒▒y
initialized fuse
initialized vfrel
initialized hwwdt
initialized ▒▒psc_irq_init...
INFO: enter idle task.
▒▒adc
fmon_populate_monitors: found ▒▒E> Binary cpubl is no▒▒199 monitors
initialized fmon
▒▒t found in comp table▒▒initialized mc
initialized reset
initialized uphy_early
initialized emc_early
469 clocks registered
initialized clk_mach
initialized clk_cal_early
initialized clk_mach_early_▒▒
▒▒config
initialized io_dpd
initialized thermal
initialized soctherm
initialized regime
initialized i2c
vrmon_dt_init: vrmon node not found
vrmon_chk_boot_state: found 0 rail monitors
initialized vrmon
initialized regulator
initialized avfs_clk_platform
initialized powergate
initialized dvs
initialized clk_mach_config
initialized pm
initialized suspend
initialized strap
initia▒▒I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_secure-os
I> Size of partition: 4194304
I> Binary@ device:3/0 block-25088 (partition ▒▒lized emc
initialized emc_mrq
▒▒size: 0x400000), name▒▒WARNING @ [platform/d▒▒: A_secure-os
▒▒rivers/clk/clk-fwk/clk-cal.c]: aon_apb is not configured by BPMP-FW
WARNING @ [platform/drivers/clk/clk-fwk/clk-cal.c]: aon_cpu_nic is not c▒▒E> Binary tos is not found in comp table
▒▒onfigured by BPMP-FW
initialized ▒▒I> MB2-params @ 0x40060000
I> CPUBL-params @ 0xc200000▒▒clk_cal
initialized ▒▒0
▒▒uphy_dt
initialized uphy_mrq
start PLL 8 calibration timeout

FATAL ERROR [FILE=platform/drivers/uphy/uphy-tegra234.c, ERR_UID=2251]: start PLL 8 cal▒▒I> cpubl: Authentication Finalize Done
I> Binary cpubl▒▒ibration failed
r0_usr  0x500886bc
r1_usr  0x000008cb
r2_usr  0x50038988
r3_usr  0x50181ec8
r4_usr  0x5000231c
▒▒ loaded successfully at 0xba800000
▒▒r5_usr▒▒I> tos: Authenticatio▒▒       0x50038988
r6_usr  0x000008cb
▒▒n Finalize Done
I> Binary tos loaded succes▒▒r7_usr     0x500886bc
▒▒sfully at 0xbeee7000  r8_fiq  0x00000000
▒▒
  r9_usr        0x501f2e70      r9_fiq  0x00000000
r10_usr 0x00000000      r10_fiq r11_usr 0x50▒▒I> Task: Prepare TOS params (0x5000fde0)
▒▒1c44e4        r11_fiq 0x00000000
r12_usr 0xc0000000      r12_fiq 0x00000000
sp_usr  0x50181ea0      sp_fiq  0x5001a620      sp_irq  0x500▒▒I> Task: OEM SC7 context save (0x5001088c)
▒▒1a600
sp_svc  0x5001a400      sp_abt  0x5001ac00      sp_und  0x5001ab70
lr_usr  0x500031d1      lr_fiq  0x▒▒I> oem sc7 context sa▒▒00000000     lr_irq  0x5005c168
lr_svc  0x5000a3d8      lr_abt  0x▒▒ved
I> Task: Disable MSS perf stats (0x5001ad88)
I> Task: Program display st▒▒00000000   lr_und  0x500▒▒icky bits (0x5001ad04)
I> Task: Storage device deinit (0x50001ca4)
I> Task: ▒▒02320
pc 0x5000231c
spsr 0x20000010
fpscr 0x20000010
Bootstrap@0x501d85a0 ▒▒SMMU init (0x5001a748)
▒▒sp 0x5▒▒I> Task: Program CBB ▒▒0181ea0 stack: 501800▒▒PCIE AMAP regions (0x500031dc)
▒▒cc - 50181ffc
call s▒▒I> Task: Program GICv▒▒tack:
sp 0x50181ea0 pc 0x5000231c
sp 0x50181ea0 pc 0x500031d0
sp 0x50181eb8 pc 0x5003897c
sp 0x50181f08 pc 0x50039878
sp 0x50181f6▒▒3 registers (0x5001ae▒▒8 pc 0x50030532
sp 0x50181fb0 pc 0x5002eb50
sp 0x5018▒▒28)
▒▒1ff0 pc 0x5006810e
sp 0x50181ff8 pc 0xaaaaaaaa
eht_idx_find: 0xaaaaaaaa not a valid code add▒▒I> Task: Audit firewall settings (0x5001817c)
▒▒ress
no eidx for 0xaaaaaaaa
▒▒I> MB2 finished

▒▒NOTICE:  BL31: v2.5(release):ef8af0b99
NOTICE:  BL31: Built : 11:45:41, Apr  6 2022
ERROR:   Error initializing runtime service trusty_fast
▒▒
  Jetson UEFI firmware (version r34.1-975eef6 built on 2022-04-06T11:46:12-07:00)




▒▒ERROR: camera-ip/isp5/isp5.c:1985 [isp5_pm_init] "ERROR: Failed to turn isp power on"
BUG: core/init/init.c:85 [init_all] "*** FIRMWARE INIT FAILED AT LEVEL 95 ***"
▒▒