[ 2.741606] tegra-pcie-dw 14100000.pcie: pex_wake already in use [ 2.979820] tegra-pcie-dw 14120000.pcie: pex_wake already in use ?? [0000.085] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0000.094] I> MB1 (prd-version: 1.5.1.6-t194-41334769-1740dd39) [0000.099] I> Boot-mode: Coldboot [0000.102] I> Chip revision : A02P [0000.105] I> Bootrom patch version : 15 (correctly patched) [0000.110] I> ATE fuse revision : 0x200 [0000.114] I> Ram repair fuse : 0x0 [0000.117] I> Ram Code : 0x2 [0000.119] I> rst_source : 0x0 [0000.122] I> rst_level : 0x0 [0000.126] I> Boot-device: eMMC [0000.141] I> sdmmc DDR50 mode [0000.145] W> No valid slot number is found in scratch register [0000.150] W> Return default slot: _a [0000.154] I> Active Boot chain : 0 [0000.157] I> Boot-device: eMMC [0000.160] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.168] I> Temperature = 39500 [0000.171] W> Skipping boost for clk: BPMP_CPU_NIC [0000.175] W> Skipping boost for clk: BPMP_APB [0000.179] W> Skipping boost for clk: AXI_CBB [0000.183] W> Skipping boost for clk: AON_CPU_NIC [0000.188] W> Skipping boost for clk: CAN1 [0000.191] W> Skipping boost for clk: CAN2 [0000.196] I> Boot-device: eMMC [0000.198] I> Boot-device: eMMC [0000.208] I> Sdmmc: HS400 mode enabled [0000.212] I> ECC region[0]: Start:0x0, End:0x0 [0000.216] I> ECC region[1]: Start:0x0, End:0x0 [0000.221] I> ECC region[2]: Start:0x0, End:0x0 [0000.225] I> ECC region[3]: Start:0x0, End:0x0 [0000.229] I> ECC region[4]: Start:0x0, End:0x0 [0000.233] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.239] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.243] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.248] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.252] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.258] E> FAILED: Thermal config [0000.265] E> FAILED: MEMIO rail config [0000.283] I> Boot-device: eMMC [0000.292] I> sdmmc bdev is already initialized [0000.367] I> MB1 done ????main enter SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init ?? [0000.375] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-feba5943) [0000.376] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0000.376] I> Default Heap @ [0xd486400 - 0xd48a400] [0000.377] E> DEVICE_PROD: Inv?? [0000.085] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0000.094] I> MB1 (prd-version: 1.5.1.6-t194-41334769-1740dd39) [0000.099] I> Boot-mode: Coldboot [0000.102] I> Chip revision : A02P [0000.105] I> Bootrom patch version : 15 (correctly patched) [0000.110] I> ATE fuse revision : 0x200 [0000.114] I> Ram repair fuse : 0x0 [0000.117] I> Ram Code : 0x2 [0000.119] I> rst_source : 0x0 [0000.122] I> rst_level : 0x0 [0000.126] I> Boot-device: eMMC [0000.140] I> sdmmc DDR50 mode [0000.145] W> No valid slot number is found in scratch register [0000.150] W> Return default slot: _a [0000.153] I> Active Boot chain : 0 [0000.157] I> Boot-device: eMMC [0000.160] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.168] I> Temperature = 39500 [0000.171] W> Skipping boost for clk: BPMP_CPU_NIC [0000.175] W> Skipping boost for clk: BPMP_APB [0000.179] W> Skipping boost for clk: AXI_CBB [0000.183] W> Skipping boost for clk: AON_CPU_NIC [0000.188] W> Skipping boost for clk: CAN1 [0000.191] W> Skipping boost for clk: CAN2 [0000.196] I> Boot-device: eMMC [0000.198] I> Boot-device: eMMC [0000.208] I> Sdmmc: HS400 mode enabled [0000.212] I> ECC region[0]: Start:0x0, End:0x0 [0000.216] I> ECC region[1]: Start:0x0, End:0x0 [0000.221] I> ECC region[2]: Start:0x0, End:0x0 [0000.225] I> ECC region[3]: Start:0x0, End:0x0 [0000.229] I> ECC region[4]: Start:0x0, End:0x0 [0000.233] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.239] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.243] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.248] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.252] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.257] E> FAILED: Thermal config [0000.265] E> FAILED: MEMIO rail config [0000.283] I> Boot-device: eMMC [0000.292] I> sdmmc bdev is already initialized [0000.367] I> MB1 done ????main enter SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init ?? [0000.375] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-feba5943) [0000.375] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0000.376] I> Default Heap @ [0xd486400 - 0xd48a400] [0000.377] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0000.382] W> device prod register failed [0000.386] I> Boot-device: eMMC [0000.389] I> Boot_device: SDMMC_BOOT instance: 3 [0000.395] I> sdmmc-3 params source = boot args [0000.398] I> sdmmc bdev is already initialized [0000.402] I> sdmmc-3 params source = boot args [0000.411] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0000.417] I> Found 42 partitions in SDMMC_USER (instance 3) [0000.418] W> No valid slot number is found in scratch register [0000.423] W> Return default slot: _a [0000.426] I> Active Boot chain : 0 [0000.430] I> parsing oem signed section of bpmp-fw header done [0000.436] I> bpmp-fw binary init read from storage [0000.440] I> oem authentication of bpmp-fw header done [0000.447] I> bpmp-fw binary done read from storage [0000.450] I> bpmp-fw: Authentication init Done [0000.454] I> parsing oem signed section of cpubl header done [0000.460] I> cpubl binary init read from storage [0000.464] I> bpmp-fw: Authentication Finalize Done [0000.469] I> oem authentication of cpubl header done [0000.473] I> cpubl binary done read from storage [0000.478] I> cpubl: Authentication init Done [0000.483] I> parsing oem signed section of rce header done [0000.487] I> rce binary init read from storage [0000.492] I> Relocating BR-BCT [0000.495] I> cpubl: Authentication Finalize Done [0000.499] I> oem authentication of rce header done [0000.504] I> rce binary done read from storage [0000.508] I> rce: Authentication init Done [0000.513] I> parsing oem signed section of ape header done [0000.517] I> ape binary init read from storage [0000.522] I> rce: Authentication Finalize Done [0000.526] I> oem authentication of ape header done [0000.530] I> ape binary done read from storage [0000.535] I> ape: Authentication init Done [0000.539] I> parsing oem signed section of tos header done [0000.544] I> tos binary init read from storage [0000.548] I> ape: Authentication Finalize Done [0000.553] I> oem authentication of tos header done [0000.557] I> tos binary done read from storage [0000.561] I> tos: Authentication init Done [0000.566] I> parsing oem signed section of bpmp-fw-dtb header done [0000.571] I> bpmp-fw-dtb binary init read from storage [0000.576] I> tos: Authentication Finalize Done [0000.582] I> oem authentication of bpmp-fw-dtb header done [0000.589] I> bpmp-fw-dtb binary done read from storage [0000.591] I> bpmp-fw-dtb: Authentication init Done [0000.596] I> parsing oem signed section of cpubl-dtb header done [0000.602] I> cpubl-dtb binary init read from storage [0000.606] I> bpmp-fw-dtb: Authentication Finalize Done [0000.644] I> oem authentication of cpubl-dtb header done [0000.644] I> cpubl-dtb binary done read from storage [0000.645] I> cpubl-dtb: Authentication init Done [0000.647] I> parsing oem signed section of eks header done [0000.647] I> eks binary init read from storage [0000.648] I> cpubl-dtb: Authentication Finalize Done [0000.649] I> oem authentication of eks header done [0000.652] I> eks binary done read from storage [0000.657] I> eks: Authentication init Done [0000.660] I> eks: Authentication Finalize Done [0000.665] I> EKB detected (length: 0x410) @ VA:0x5270a400 ??NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 14:42:47, Jan 15 2021 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 40: hwkey-agent is running!! hwkey-agent: 197: key_mgnt_processing ....... hwkey-agent: 189: Setting EKB key 0 to slot 14 hwkey-agent: 167: Init hweky-agent services!! luks-srv: 40: luks-srv is running!! luks-srv: 157: Init luks-srv IPC services!! platform_bootstrap_epilog: trusty bootstrap complete ?? welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is e73a758761f0c6d24a1e69a2ac6b5035 tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized 392 clocks registered WARNING: pll_c4 has no dyn ramp clk_mrq_init: mrq handler registered clk initialized nvlink initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized uphy_mrq_init: mrq handler registered uphy_dt initialized uphy initialized safereg_init: period 80 ms ec_late initialized ?? ??mrq initialized ??[0001.166] I> Welcome to Cboot ??fmon_post initialized ??[0001.167] I> Cboot Version: t194-9efcbc4f [0001.167] I> CPU-BL Params @ 0xf2820000 [0001.168] I> 0) Base:0x00000000 Size:0x00000000 [0001.171] I> 1) Base:0xf1100000 Size:0x00100000 [0001.176] I> 2) Base:0xf2000000 Size:0x00200000 [0001.180] I> 3) Base:0xf1200000 Size:0x00200000 [0001.185] I> 4) Base:0xf1000000 Size:0x00100000??clk_set_parent failed for clk i2c2, parent pll_aon (-22) clk_set_parent failed for clk i2c8, parent pll_aon (-22) clk_dt_late initialized machine_check initialized pm_post initialized dbells initialized avfs_clk_platform_post initialized dmce initialized cvc initialized ccplex_avfs_hw_init: nafll_cluster0: not monitored ccplex_avfs_hw_init: nafll_cluster1: not monitored ccplex_avfs_hw_init: nafll_cluster2: not monitored ccplex_avfs_hw_init: nafll_cluster3: not monitored avfs_clk_mach_post initialized regulator_post initialized rm initialized sc7_diag initialized thermal_test initialized serial_late initialized clk_post initialized clk_dt_post initialized mc_reg initialized pg_post initialized dyn_modules initialized sku_debugfs initialized speedo_debugfs initialized adc_debugfs initialized clk_debugfs initialized ?? [0001.264] I> 5) Base:0xf0f00000 Size:0x00100000 [0001.269] I> 6) Base:0xf3800000 Size:0x00400000 [0001.273] I> 7) Base:0xf1c00000 Size:0x00400000 [0001.278] I> 8) Base:0xf0e00000 Size:0x00100000 [0001.282] I> 9) Base:0xf0d00000 Size:0x00100000 [0001.287] I> 10) Base:0xf3000000 Size:0x00800000 [0001.291] I> 11) Base:0x40000000 Size:0x00040000 [0001.296] I> 12) Base:0xf0c00000 Size:0x00100000 [0001.300] I> 13) Base:0x40046000 Size:0x00002000 [0001.304] I> 14) Base:0x40048000 Size:0x00002000 ??emc_debugfs initialized dvs_debugfs initialized ??[0001.309] I> 15) Base:0xac000000 Size:0x00004000 ??fmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized debugfs_cons initialized mail_fs initialized profile initialized cvc_debugfs initialized dmce_debugfs initialized ec_debugfs initialized rm_debugfs initialized soctherm_debug initialized gr_reader initialized mods initialized dt_fs initialized debugfs_mrq initialized debug_mrq initialized debug_safereg initialized initializing target calling apps_init() starting app shell entering main console loop ] ??[0001.318] I> 16) Base:0x4004a000 Size:0x00002000 [0001.369] I> 17) Base:0xf0b00000 Size:0x00100000 [0001.373] I> 18) Base:0x4004c000 Size:0x00002000 [0001.378] I> 19) Base:0xf2200000 Size:0x00600000 [0001.382] I> 20) Base:0x4004e000 Size:0x00002000 [0001.386] I> 21) Base:0xf0ad0000 Size:0x0000c000 [0001.391] I> 22) Base:0x00000000 Size:0x00000000 [0001.395] I> 23) Base:0xf0ae0000 Size:0x00020000 [0001.400] I> 24) Base:0xf6000000 Size:0x02000000 [0001.404] I> 25) Base:0x40050000 Size:0x00002000 [0001.409] I> 26) Base:0x40040000 Size:0x00006000 [0001.413] I> 27) Base:0xf1800000 Size:0x00400000 [0001.418] I> 28) Base:0xf4c00000 Size:0x01400000 [0001.422] I> 29) Base:0xf1400000 Size:0x00400000 [0001.427] I> 30) Base:0x00000000 Size:0x00000000 [0001.431] I> 31) Base:0x00000000 Size:0x00000000 [0001.436] I> 32) Base:0xf8000000 Size:0x08000000 [0001.440] I> 33) Base:0x00000000 Size:0x00000000 [0001.444] I> 34) Base:0xf3c00000 Size:0x01000000 [0001.449] I> 35) Base:0xab000000 Size:0x01000000 [0001.453] I> 36) Base:0xa0000000 Size:0x0b000000 [0001.458] I> 37) Base:0xf2800000 Size:0x00800000 [0001.462] I> 38) Base:0x80000000 Size:0x20000000 [0001.467] I> 39) Base:0xb0000000 Size:0x08000000 [0001.471] I> 40) Base:0x00000000 Size:0x00000000 [0001.476] I> 41) Base:0x00000000 Size:0x00000000 [0001.480] I> 42) Base:0x00000000 Size:0x00000000 [0001.485] I> 43) Base:0x00000000 Size:0x00000000 [0001.489] I> 44) Base:0x00000000 Size:0x00000000 [0001.494] I> 45) Base:0x00000000 Size:0x00000000 [0001.498] GIC-SPI Target CPU: 0 [0001.501] Interrupts Init done [0001.504] calling constructors [0001.507] initializing heap [0001.509] I> Heap: [0xa06945e8 ... 0xab000000] [0001.514] initializing threads [0001.517] initializing timers [0001.519] creating bootstrap completion thread [0001.524] top of bootstrap2() [0001.526] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000 [0001.531] initializing platform [0001.534] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0001.539] W> device prod register failed [0001.543] I> Bl_dtb @0xaaf00000 [0001.550] W> "plugin-manager" doesn't exist, creating [0001.551] W> "ids" doesn't exist, creating [0001.555] W> "connection" doesn't exist, creating [0001.560] W> "configs" doesn't exist, creating [0001.569] I> Find /i2c@3160000's alias i2c0 [0001.569] I> Reading eeprom i2c=0 address=0x50 [0001.597] I> Device at /i2c@3160000:0x50 [0001.598] I> Reading eeprom i2c=0 address=0x56 [0001.598] E> I2C: slave not found in slaves. [0001.599] E> I2C: Could not write 0 bytes to slave: 0x00ac with repeat start true. [0001.600] E> I2C_DEV: Failed to send register address 0x00000000. [0001.600] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xac at 0x00000000 via instance 0. [0001.608] E> eeprom: Failed to read I2C slave device [0001.612] I> Eeprom read failed 0x3526070d [0001.618] I> Find /i2c@3180000's alias i2c2 [0001.620] I> Reading eeprom i2c=2 address=0x54 [0001.626] E> I2C: slave not found in slaves. [0001.629] E> I2C: Could not write 0 bytes to slave: 0x00a8 with repeat start true. [0001.637] E> I2C_DEV: Failed to send register address 0x00000000. [0001.642] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa8 at 0x00000000 via instance 2. [0001.652] E> eeprom: Failed to read I2C slave device [0001.656] I> Eeprom read failed 0x3526070d [0001.660] I> Reading eeprom i2c=2 address=0x57 [0001.665] E> I2C: slave not found in slaves. [0001.669] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0001.677] E> I2C_DEV: Failed to send register address 0x00000000. [0001.682] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 2. [0001.692] E> eeprom: Failed to read I2C slave device [0001.697] I> Eeprom read failed 0x3526070d [0001.700] I> Reading eeprom i2c=2 address=0x52 [0001.705] E> I2C: slave not found in slaves. [0001.709] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.717] E> I2C_DEV: Failed to send register address 0x00000000. [0001.722] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 2. [0001.732] E> eeprom: Failed to read I2C slave device [0001.737] I> Eeprom read failed 0x3526070d [0001.742] I> Find /i2c@c240000's alias i2c1 [0001.745] I> Reading eeprom i2c=1 address=0x52 [0001.750] E> I2C: slave not found in slaves. [0001.753] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.761] E> I2C_DEV: Failed to send register address 0x00000000. [0001.766] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.776] E> eeprom: Retry to read I2C slave device. [0001.781] E> I2C: slave not found in slaves. [0001.785] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.793] E> I2C_DEV: Failed to send register address 0x00000000. [0001.798] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.808] E> eeprom: Failed to read I2C slave device [0001.813] I> Eeprom read failed 0x3526070d [0001.816] I> Reading eeprom i2c=1 address=0x50 [0001.821] E> I2C: slave not found in slaves. [0001.825] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.833] E> I2C_DEV: Failed to send register address 0x00000000. [0001.838] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.848] E> eeprom: Retry to read I2C slave device. [0001.853] E> I2C: slave not found in slaves. [0001.857] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.865] E> I2C_DEV: Failed to send register address 0x00000000. [0001.870] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.880] E> eeprom: Failed to read I2C slave device [0001.884] I> Eeprom read failed 0x3526070d [0001.888] I> create_pm_ids: id: 2888-0004-400-M, len: 15 [0001.894] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.905] I> Adding plugin-manager/ids/2888-0004-400=/i2c@3160000:module@0x50 [0001.912] W> "i2c@3160000" doesn't exist, creating [0001.916] W> "module@0x50" doesn't exist, creating [0001.923] I> Adding plugin-manager/cvm [0001.925] W> "chip-id" doesn't exist, creating [0001.929] I> Adding plugin-manager/chip-id/A02P [0001.933] I> Plugin-manager override starting [0001.939] I> node /plugin-manager/fragement-tegra-wdt-en matches [0001.948] I> node /plugin-manager/fragement-soft-wdt matches [0001.956] I> node /plugin-manager/fragment-pcie-c5-rp matches [0001.969] I> Disable plugin-manager status in FDT [0001.969] I> Plugin-manager override finished successfully [0001.970] I> gpio framework initialized [0001.971] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver [0001.977] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver [0001.983] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 [0001.991] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0001.998] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.005] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.011] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 [0002.018] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.026] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.033] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.040] I> fixed regulator driver initialized [0002.055] I> register 'maxim' power off handle [0002.056] I> virtual i2c enabled [0002.056] I> registered 'maxim,max20024' pmic [0002.056] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver [0002.061] I> Boot-device: eMMC [0002.064] I> Boot_device: SDMMC_BOOT instance: 3 [0002.073] I> sdmmc-3 params source = boot args [0002.073] I> create_pm_ids: id: 2888-0004-400-M, len: 15 [0002.078] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.089] I> sdmmc bdev is already initialized [0002.093] I> sdmmc-3 params source = boot args [0002.124] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0002.137] I> Found 42 partitions in SDMMC_USER (instance 3) [0002.147] I> enabling 'vdd-hdmi-p2-5v0' regulator [0002.152] I> regulator 'vdd-hdmi-p2-5v0' already enabled [0002.153] E> tegrabl_display_init_regulator: hdmi cable is not connected [0002.153] E> tegrabl_display_get_pdata, failed to parse dtb settings [0002.160] I> regulator 'vdd-hdmi-p1-5v0' already enabled [0002.165] I> regulator 'vdd-hdmi-p1-5v0' already enabled [0002.166] E> tegrabl_display_init_regulator: hdmi cable is not connected [0002.166] E> tegrabl_display_get_pdata, failed to parse dtb settings [0002.172] E> invalid display type [0002.173] E> cannot find any other nvdisp nodes [0002.176] E> no valid display unit config found in dtb [0002.182] W> display init failed [0002.184] I> Load in CBoot Boot Options partition and parse it [0002.195] E> Error -9 when finding node with path /boot-configuration [0002.196] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO file. [0002.203] I> Using default boot order [0002.206] I> boot-dev-order :- [0002.209] I> 1.sd [0002.211] I> 2.usb [0002.213] I> 3.nvme [0002.215] I> 4.emmc [0002.217] I> 5.net [0002.219] I> Hit any key to stop autoboot: 4 3 2 1 [0004.226] initializing target [0004.226] calling apps_init() [0004.227] starting app kernel_boot_app [0004.246] I> found decompressor handler: lz4-legacy [0004.247] I> decompressing BMP blob ... [0004.258] I> Kernel type = Normal [0004.259] I> Loading kernel-bootctrl from partition [0004.259] I> Loading partition kernel-bootctrl at 0xa42d0000 from device(0x1) [0004.266] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0004.266] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0004.267] I> ########## SD (0) boot ########## [0004.267] I> No sdcard [0004.269] I> -0 params source = [0004.272] E> Blockdev open: exit error [0004.275] E> SD boot failed, err: 724238353 [0004.279] I> ########## USB (0) boot ########## [0004.289] W> No valid slot number is found in scratch register [0004.290] W> Return default slot: _a [0004.305] I> USB Firmware Version: 60.06 release [0004.361] I> regulator of usb2-0 already enabled [0004.370] I> enabling 'usb-p9-0-5v0' regulator [0004.376] I> regulator of usb2-2 already enabled [0004.383] I> regulator of usb2-3 already enabled [0005.387] E> failed to initialize xhci controller [0005.387] E> Error in init of XUSB host driver, err: 79790026 [0005.388] W> Failed to initialize device 5-0 [0005.388] E> USB boot failed, err: 2037973030 [0005.389] I> ########## Fixed storage boot ########## [0005.395] I> Already published: 00010003 [0005.395] I> Look for boot partition [0005.396] I> Fallback: assuming 0th partition is boot partition [0005.398] I> Detect filesystem [0005.425] I> Loading extlinux.conf ... [0005.426] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf [0005.463] I> L4T boot options [0005.463] I> [1]: "primary kernel" [0005.463] I> Enter choice: [0008.464] I> Continuing with default option: 1 [0008.464] I> Loading kernel sig file from rootfs ... [0008.464] I> rootfs path: /sdmmc_user/boot/Image.sig [0008.489] I> Loading kernel binary from rootfs ... [0008.489] I> rootfs path: /sdmmc_user/boot/Image [0008.714] I> overload load_size to 34539528 (from 34539536) [0008.732] I> Validate kernel ... [0008.732] I> T19x: Authenticate kernel (bin_type: 37), max size 0x5000000 [0009.047] I> Encryption fuse is not ON [0009.067] I> No kernel-dtb binary path [0009.067] W> No valid slot number is found in scratch register [0009.068] W> Return default slot: _a [0009.068] I> A/B: bin_type (38) slot 0 [0009.068] I> Loading kernel-dtb from partition [0009.069] I> Loading partition kernel-dtb at 0x91000000 from device(0x1) [0009.077] I> Validate kernel-dtb ... [0009.077] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x400000 [0009.082] I> Encryption fuse is not ON [0009.083] I> Loading ramdisk from rootfs ... [0009.087] I> Loading initrd sig file from rootfs ... [0009.092] I> rootfs path: /sdmmc_user/boot/initrd.sig [0009.115] I> Loading initrd binary from rootfs ... [0009.115] I> rootfs path: /sdmmc_user/boot/initrd [0009.180] I> overload load_size to 7236790 (from 7236800) [0009.182] I> Validate initrd ... [0009.182] I> T19x: Authenticate initrd (bin_type: 49), max size 0x4000000 [0009.249] I> Encryption fuse is not ON [0009.256] I> Kernel hdr @0xa42d0000 [0009.257] I> Kernel dtb @0x90000000 [0009.257] I> decompressor handler not found [0009.257] I> Copying kernel image (34539528 bytes) from 0xa42d0000 to 0x80080000 ... [0009.263] I> Done [0009.264] I> Updated bpmp info to DTB [0009.265] I> Ramdisk: Base: 0x92000000; Size: 0x6e6cb6 [0009.265] I> Updated initrd info to DTB [0009.266] W> WARN: Fail to override "console=none" in commandline [0009.269] I> Active rootfs suffix: [0009.273] E> tegrabl_linuxboot_add_disp_param, du 0 failed to get display params [0009.280] E> tegrabl_linuxboot_add_disp_param, du 0 failed to get display params [0009.287] E> tegrabl_linuxboot_add_disp_param, du 0 failed to get display params [0009.295] W> No valid slot number is found in scratch register [0009.300] W> Return default slot: _a [0009.304] I> Active slot suffix: [0009.307] I> add_boot_slot_suffix: slot_suffix = [0009.311] I> Linux Cmdline: console=ttyTCU0,115200 video=tegrafb no_console_suspend=1 earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt rootfs.slot_suffix= usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=8 boot.slot_suffix= boot.ratchetvalues=0.4.2 vpr_resize sdhci_tegra.en_boot_part_access=1 [0009.338] I> Updated bootarg info to DTB [0009.341] W> MAC addr invalid! [0009.344] E> Failed to get WIFI MAC address [0009.348] W> MAC addr invalid! [0009.351] E> Failed to get Bluetooth MAC address [0009.356] I> eeprom_get_mac_addr: MAC (type: 2): 48:b0:2d:4d:43:31 [0009.362] W> "plugin-manager" doesn't exist, creating [0009.367] I> Adding /chosen/plugin-manager/cvm [0009.371] W> "chip-id" doesn't exist, creating [0009.375] I> Adding /chosen/plugin-manager/chip-id [0009.380] W> "configs" doesn't exist, creating [0009.384] I> Adding /chosen/plugin-manager/configs [0009.389] W> "ids" doesn't exist, creating [0009.393] I> Adding /chosen/plugin-manager/ids [0009.397] W> "odm-data" doesn't exist, creating [0009.401] I> Adding /chosen/plugin-manager/odm-data [0009.409] W> "memory" doesn't exist, creating [0009.411] I> [0] START: 0x80000000, END: 0xac000000 [0009.415] I> [1] START: 0xac004000, END: 0xf0ad0000 [0009.420] I> [2] START: 0xf0adc000, END: 0xf0ae0000 [0009.424] I> dram_block larger than 80000000 [0009.428] I> [3] START: 0x100000000, END: 0x880000000 [0009.433] I> added [base:0x80000000, size:0x2c000000] to /memory [0009.439] I> added [base:0xac200000, size:0x44800000] to /memory [0009.445] I> added [base:0x100000000, size:0x780000000] to /memory [0009.452] I> Updated memory info to DTB [0009.455] E> add_disp_param: failed to get display params for du=0 [0009.461] W> "reset" doesn't exist, creating [0009.465] I> Adding ecid(0000000164060084080000000e028200) to DT [0009.471] I> NVG: Logical CPU: 0; MPIDR: 0x80000000 [0009.476] I> NVG: Logical CPU: 1; MPIDR: 0x80000001 [0009.480] I> NVG: Logical CPU: 2; MPIDR: 0x80000100 [0009.485] I> NVG: Logical CPU: 3; MPIDR: 0x80000101 [0009.490] I> NVG: Logical CPU: 4; MPIDR: 0x80000200 [0009.494] I> NVG: Logical CPU: 5; MPIDR: 0x80000201 [0009.499] I> NVG: Logical CPU: 6; MPIDR: 0x80000300 [0009.504] I> NVG: Logical CPU: 7; MPIDR: 0x80000301 [0009.509] W> "misc-data" doesn't exist, creating [0009.513] I> Boot-device: eMMC [0009.516] I> Add boot-sdmmc to plugin-manager/misc-data [0009.521] I> Add storage-sdmmc to plugin-manager/misc-data [0009.526] W> Unknown storage device [0009.531] I> Add serial number:1422621079643 as DT property [0009.536] I> Plugin-manager override starting [0009.540] I> node /plugin-manager/fragement-tegra-wdt-en matches [0009.547] I> node /plugin-manager/fragement-soft-wdt matches [0009.554] I> node /plugin-manager/fragment-pcie-c5-rp matches [0009.564] I> Disable plugin-manager status in FDT [0009.564] I> Plugin-manager override finished successfully [0009.567] I> tegrabl_load_kernel_and_dtb: Done [0009.571] E> tegrabl_display_clear: display is not initialized [0009.576] W> Boot logo display failed... [0009.580] I> Kernel EP: 0x80080000, DTB: 0x90000000 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (realtimes@realtimes-IdeaCentre-GeekPro-15ICK) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #2 SMP PREEMPT Wed Feb 3 11:23:50 CST 2021 [ 0.000000] Boot CPU: AArch64 Processor [4e0f0040] [ 0.000000] OF: fdt:memory scan node memory, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 2c000000 [ 0.000000] OF: fdt: - ac200000 , 44800000 [ 0.000000] OF: fdt: - 100000000 , 780000000 [ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '') [ 0.000000] bootconsole [tegra_comb_uart0] enabled [ 1.821909] tegra-xudc-new 3550000.xudc: extcon_get_extcon_dev_by_cable failed -19 [ 2.683882] tegra-pcie-dw 14100000.pcie: pex_wake already in use [ 2.933054] tegra-pcie-dw 14120000.pcie: pex_wake already in use [ 9.310189] tegra-pcie-dw 14140000.pcie: pex_wake already in use [ 9.824412] tegra-pcie-dw 14160000.pcie: pex_wake already in use [ 10.342972] tegra-pcie-dw 141a0000.pcie: pex_wake already in use [ 11.380982] cgroup: cgroup2: unknown option "nsdelegate" [ 11.542822] systemd[1]: /etc/systemd/system/todeskd.service:8: Failed to parse service restart specifier, ignoring: 3s [ 12.982407] random: crng init done [ 12.982494] random: 7 urandom warning(s) missed due to ratelimiting Ubuntu 18.04.5 LTS nvidia-RoboSense ttyTCU0 nvidia-RoboSense login: [ 22.101191] edid invalid [ 22.110935] edid invalid [ 22.117818] edid invalid ??WARNING: pll_d3 has no dyn ramp