NvShell>help
Info: Executing cmd: help, argc: 0, args: 
DEBUG: command_help()
aurixreset                                                      : Power cycle board including Aurix
date [0x12345678]                                               : Set date = 0x12345678 on Aurix in seconds(Unix style)
version                                                         : Show the current flashed/runing firmware version
cansetbr [a|b|c|d|e|f] [125|250|500]                            : Switch baudrate of requested CAN channel to supported baudrate
cycliccanon [CAN|CANFD|CANEx|All]                               : Switch on Cyclic CAN/CANFD/CANEx messages (for AURIX)
cycliccanoff [CAN|CANFD|CANEx|All]                              : Switch off Cyclic CAN/CANFD/CANEx messages (for AURIX)
i2cread x y z n                                                 : Reads 'n' bytes from device 'y' at offset 'z' of I2C-controller 'x' (all hex-byte-values)
i2cscan [0]                                                     : Scan all connected I2C devices at I2C module 0
i2cwrite x y z n b0 b1 ...                                      : Writes 'n' bytes to device 'y' at offset 'z' , values Byte-b0, Byte-b1 .... of I2C-controller 'x' (all hex-byte-values)
inforomdump                                                     : Dump the Inforom content in hex format
help                                                            : Shows all available commands supported
poweron                                                         : Turn main power on and release Tegra resets
poweroff [safeshutdown]                                         : Set the outputs to system power off state
readNvRam                                                       : Read NvRam content
setdfltbtchain [x1] [A|B|C|D]                                  : Set default boot chain configuration for Tegra x1 to A|B|C|D
getdfltbtchain [x1]                                            : Get default boot chain configuration for Tegra x1 
setnxtbtchain [x1] [A|B|C|D]                                   : Set next boot chain for Tegra x1 to A|B|C|D
getnxtbtchain [x1]                                             : Get next boot chain configuration for x1 
tegrarecovery [x1] [on|off]                                     : Set Tegra X1 in recovery mode
tegrareset [x1] [h]                                             : Reset Tegra X1. Default is 'X1'. If 'h' option is supplied, then hold the specified Tegra in reset.
gptpon                                                          : Enable Aurix as PTP master
gptpoff                                                         : Disable Aurix as PTP master
status                                                          : Display the Aurix internal status
setnetworkconfig [0-10]                                         : Set Network Config
getnetworkconfig                                               : Get Network Config
show_fanrpm                                                     : Show RPM of all fans
set_fanpwm [1|2] [DutyCyclePercentage]                        : Set Fan PWM ie., DutyCycle
get_temperature                                                : get temperature
send_temperature [Temperature]                                 : Send temperature
set_tmonerror [init|rdwr|lcltgl|rmttgl|tmonalert|tmontherm]    : inject false case
setistconfig [config]                                           : Set Tegra IST configuration
istabort                                                         : Abort IST 
getistinfo                                                      : Get Tegra IST information
getistconfig                                                    : Get Tegra IST configuration
getistresult [ [SeqNo] ]                                        : Get Tegra IST Results
entersc7                                                         : Enter SC7 power mode
exitsc7                                                          : Exit from SC7 power mode
readvrs10status                                                : Read VRS10 Status register
readvrs11status                                                : Read VRS11 Status register
vrs10injecterror [inputs|regwrite|nirqtoggle]                  : Inject faults in VRS10
vrs11injecterror [regwrite1|regwrite2]                         : Inject faults in VRS11
vrs12injcterror [overror|uverror|wrongcrc|plauscheck]          : Inject faults in VRS12
Command Executed
NvShell>MCU_FOH: ErrReport: ErrorCode-0x30004000 ReporterId-0x8060 Error_Attribute-0x0 Timestamp-0x8274d718
MCU_FOH: ErrReport: ErrorCode-0x89abcdef ReporterId-0x8013 Error_Attribute-0x0 Timestamp-0x82750f61
ERROR: MCU_SWC_FanControl: count_EthFrameDrop expired
ERROR: MCU_SWC_FanControl:  Ethernet Tegra A frames missing for consecutive = 4 times
ERROR: MCU_SWC_FanControl: moving to error state
MCU_FOH: ErrReport: ErrorCode-0x30000002 ReporterId-0x8060 Error_Attribute-0x0 Timestamp-0xdbb8e9ce
MCU_FOH: ErrReport: ErrorCode-0x30008000 ReporterId-0x8060 Error_Attribute-0x0 Timestamp-0xf12a5af3
MCU_FOH: ErrReport: ErrorCode-0x30008000 ReporterId-0x8060 Error_Attribute-0x0 Timestamp-0xbb39386b
MCU_FOH: ErrReport: ErrorCode-0x30008000 ReporterId-0x8060 Error_Attribute-0x0 Timestamp-0x71fb5063
MCU_FOH: ErrReport: ErrorCode-0x30000001 ReporterId-0x8060 Error_Attribute-0x0 Timestamp-0xfbf51656
MCU_FOH: ErrReport: ErrorCode-0x30000002 ReporterId-0x8060 Error_Attribute-0x0 Timestamp-0xfbf526b7
MCU_FOH: ErrReport: ErrorCode-0x30000004 ReporterId-0x8060 Error_Attribute-0x0 Timestamp-0xfbf53594
MCU_FOH: ErrReport: ErrorCode-0x2116 ReporterId-0xe04d Error_Attribute-0x0 Timestamp-0xe6a10261