[0000.239] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.245] Processing in cold boot mode Bootloader 2
[0000.249] A02 Bootrom Patch rev = 1023
[0000.253] Power-up reason: pmc por
[0000.256] No Battery Present
[0000.259] pmic max77620 reset reason
[0000.262] pmic max77620 NVERC : 0xfe
[0000.265] RamCode = 0
[0000.268] Platform has DDR4 type RAM
[0000.271] max77620 disabling SD1 Remote Sense
[0000.275] Setting DDR voltage to 1125mv
[0000.279] Serial Number of Pmic Max77663: 0x1a0ce5
[0000.287] Entering ramdump check
[0000.290] Get RamDumpCarveOut = 0x0
[0000.293] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.298] Last reboot was clean, booting normally!
[0000.303] Sdram initialization is successful 
[0000.307] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.313] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.319] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.325] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.331] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.337] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.342] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.348] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.364] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.370] Platform-DebugCarveout: 0
[0000.374] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.379] Non secure mode, and RB not enabled.
[0000.396] Csd NumOfBlocks=0
[0000.592] *** Booting BFS0.
[0000.594] Read PT from (0:3)
[0000.600] Using BFS PT to query partitions 
[0000.605] PT: Partition LNX NOT found ! 
[0001.208] *** Booting KFS0.
[0001.210] BoardID = 3448, SKU = 0x2
[0001.214] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.219] Read GPT from (0:3)
[0001.227] Using GPT Primary to query partitions
[0001.232] Loading Tboot-CPU binary
[0001.239] Verifying TBC in OdmNonSecureSBK mode
[0001.249] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0001.256] Bootloader downloaded successfully.
[0001.260] Downloaded Tboot-CPU binary to 0xa0000258
[0001.265] MAX77620_GPIO5 configured
[0001.269] CPU power rail is up
[0001.271] CPU clock enabled
[0001.275] Performing RAM repair
[0001.278] Updating A64 Warmreset Address to 0xa00002e9
[0001.283] BoardID = 3448, SKU = 0x2
[0001.286] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.293] Loading NvTbootBootloaderDTB
[0001.310] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0001.383] Bootloader DTB Load Address: 0x83000000
[0001.387] BoardID = 3448, SKU = 0x2
[0001.391] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.396] Loading NvTbootKernelDTB
[0001.413] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0001.486] Kernel DTB Load Address: 0x83100000
[0001.490] BoardID = 3448, SKU = 0x2
[0001.494] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.501] Loading cboot binary
[0001.512] Verifying EBT in OdmNonSecureSBK mode
[0001.553] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0001.560] Bootloader downloaded successfully.
[0001.565] BoardID = 3448, SKU = 0x2
[0001.568] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.574] PT: Partition NCT NOT found ! 
[0001.578] Warning: Find Partition via PT Failed
[0001.582] Next binary entry address: 0x92c00258 
[0001.587] BoardId: 3448
[0001.591] Overriding pmu board id with proc board id
[0001.596] Display board id is not available 
[0001.600] BoardID = 3448, SKU = 0x2
[0001.604] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.617] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.674] /bpmp deleted
[0001.676] SC7EntryFw header found loaded at 0xff700000
[0001.871] OVR2 PMIC
[0001.873] Bpmp FW successfully loaded
[0001.877] BoardID = 3448, SKU = 0x2
[0001.880] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.887] WB0 init successfully at 0xff780000
[0001.891] Set NvDecSticky Bits
[0001.895] GSC2 address ff53fffc value c0edbbcc
[0001.901] GSC MC Settings done
[0001.904] BoardID = 3448, SKU = 0x2
[0001.907] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.914] TOS Image length 53680
[0001.917]  Monitor size 53680
[0001.920]  OS size 0
[0001.925] Secure Os AES-CMAC Verification Success!
[0001.930] TOS image cipher info: plaintext
[0001.934] Loading and Validation of Secure OS Successful
[0001.950] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.954] NvTbootPackSdramParams: start. 
[0001.959] NvTbootPackSdramParams: done. 
[0001.963] Tegraboot started after 169175 us
[0001.967] Basic modules init took 1479714 us
[0001.971] Sec Bootdevice Read Time = 563 ms, Read Size = 14649 KB
[0001.977] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.983] Next stage binary read took 7384 us
[0001.987] Carveout took -28689 us
[0001.990] CPU initialization took 383041 us
[0001.994] Total time taken by TegraBoot 1841450 us

[0001.999] Starting CPU & Halting co-processor 

64NOTICE:  BL31: v1.3(release):5b49e7f80
NOTICE:  BL31: Built : 08:37:40, Feb 19 2021
ERROR:   Error initializing runtime service trusty_fast
[0002.121] RamCode = 0
[0002.126] LPDDR4 Training: Read DT: Number of tables = 2
[0002.131] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0002.143] EMC Training Successful
[0002.146] 408000 not found in DVFS table
[0002.153] RamCode = 0
[0002.156] DT Write: emc-table@204000 succeeded
[0002.162] DT Write: emc-table@1600000 succeeded
[0002.166] LPDDR4 Training: Write DT: Number of tables = 2
[0002.227] 
[0002.228] Debug Init done
[0002.231] Marked DTB cacheable
[0002.234] Bootloader DTB loaded at 0x83000000
[0002.238] Marked DTB cacheable
[0002.241] Kernel DTB loaded at 0x83100000
[0002.245] DeviceTree Init done
[0002.258] Pinmux applied successfully
[0002.263] gicd_base: 0x50041000
[0002.266] gicc_base: 0x50042000
[0002.269] Interrupts Init done
[0002.273] Using base:0x60005090 & irq:208 for tick-timer
[0002.278] Using base:0x60005098 for delay-timer
[0002.283] platform_init_timer: DONE
[0002.286] Timer(tick) Init done
[0002.290] osc freq = 38400 khz
[0002.294] 
[0002.295] Welcome to L4T Cboot
[0002.298] 
[0002.299] Cboot Version: 00.00.2018.01-t210-39562017
[0002.304] calling constructors
[0002.307] initializing heap
[0002.310] initializing threads
[0002.313] initializing timers
[0002.315] creating bootstrap completion thread
[0002.320] top of bootstrap2()
[0002.323] CPU: ARM Cortex A57
[0002.326] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0002.330] initializing platform
[0002.384] Config for emmc ddr50 mode completed
[0002.389] sdmmc bdev is already initialized
[0002.393] Enable APE clock
[0002.395] Un-powergate APE partition
[0002.399] of_register: registering tegra_udc to of_hal
[0002.404] of_register: registering inv20628-driver to of_hal
[0002.410] of_register: registering ads1015-driver to of_hal
[0002.415] of_register: registering lp8557-bl-driver to of_hal
[0002.421] of_register: registering bq2419x_charger to of_hal
[0002.426] of_register: registering bq27441_fuel_gauge to of_hal
[0002.438] gpio framework initialized
[0002.441] of_register: registering tca9539_gpio to of_hal
[0002.447] of_register: registering tca9539_gpio to of_hal
[0002.452] of_register: registering i2c_bus_driver to of_hal
[0002.458] of_register: registering i2c_bus_driver to of_hal
[0002.463] of_register: registering i2c_bus_driver to of_hal
[0002.469] pmic framework initialized
[0002.472] of_register: registering max77620_pmic to of_hal
[0002.478] regulator framework initialized
[0002.482] of_register: registering tps65132_bl_driver to of_hal
[0002.488] initializing target
[0002.493] gpio_driver_register: register 'tegra_gpio_driver' driver
[0002.504] fixed regulator driver initialized
[0002.522] initializing OF layer
[0002.525] NCK carveout not present
[0002.528] Skipping dts_overrides
[0002.532] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.550] I2C Bus Init done
[0002.552] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.563] I2C Bus Init done
[0002.565] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.576] I2C Bus Init done
[0002.578] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.589] I2C Bus Init done
[0002.591] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.602] I2C Bus Init done
[0002.604] of_children_init: Ops found for compatible string maxim,max77620
[0002.615] max77620_init using irq 118
[0002.620] register 'maxim,max77620' pmic
[0002.624] gpio_driver_register: register 'max77620-gpio' driver
[0002.630] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.641] I2C Bus Init done
[0002.644] NCK carveout not present
[0002.654] Find /i2c@7000c000's alias i2c0
[0002.658] get eeprom at 1-a0, size 256, type 0
[0002.667] Find /i2c@7000c500's alias i2c2
[0002.671] get eeprom at 3-a0, size 256, type 0
[0002.675] get eeprom at 3-ae, size 256, type 0
[0002.679] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.685] I2C slave not started
[0002.688] I2C write failed
[0002.690] Writing offset failed
[0002.693] eeprom_init: EEPROM read failed
[0002.697] pm_ids_update: eeprom init failed
[0002.701] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.732] pm_ids_update: The pm board id is 3448-0002-400
[0002.738] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0002.747] pm_ids_update: pm id update successful
[0002.751] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.757] I2C slave not started
[0002.760] I2C write failed
[0002.762] Writing offset failed
[0002.765] eeprom_init: EEPROM read failed
[0002.769] pm_ids_update: eeprom init failed
[0002.799] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.805] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.813] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.819] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.827] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3e:8b:1b
[0002.833] Plugin Manager: Parse ODM data 0x000a4000
[0002.846] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0002.861] Find /i2c@7000c000's alias i2c0
[0002.864] get eeprom at 1-a0, size 256, type 0
[0002.873] Find /i2c@7000c500's alias i2c2
[0002.877] get eeprom at 3-a0, size 256, type 0
[0002.882] get eeprom at 3-ae, size 256, type 0
[0002.886] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.891] I2C slave not started
[0002.894] I2C write failed
[0002.897] Writing offset failed
[0002.900] eeprom_init: EEPROM read failed
[0002.904] pm_ids_update: eeprom init failed
[0002.908] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.938] pm_ids_update: The pm board id is 3448-0002-400
[0002.944] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0002.951] pm_ids_update: pm id update successful
[0002.956] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.961] I2C slave not started
[0002.964] I2C write failed
[0002.967] Writing offset failed
[0002.970] eeprom_init: EEPROM read failed
[0002.974] pm_ids_update: eeprom init failed
[0003.004] Add serial number:1421621010071 as DT property
[0003.012] Applying platform configs
[0003.018] platform-init is not present. Skipping
[0003.023] calling apps_init()
[0003.044] Found 17 GPT partitions in "sdmmc3_user"
[0003.049] Proceeding to Cold Boot
[0003.052] starting app android_boot_app
[0003.056] Device state: unlocked
[0003.059] display console init
[0003.067] could not find regulator
[0003.070] hdmi cable connected
[0003.109] DT entry for leds-pwm not found
[0005.081] I2C transfer timeout
[0005.084] I2C write failed
[0005.086] Writing offset failed
[0005.089] could not read edid
[0005.094] tmds-config node not found
[0005.098] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts
[0005.113] setting 'vdd-1v8' regulator to 1800000 micro volts
[0005.120] could not find regulator
[0005.123] could not find regulator
[0005.127] could not find regulator
[0005.155] using default cmu settings
[0005.159] dc_hdmi_enable, starting HDMI initialisation
[0005.165] dc_hdmi_enable, HDMI initialisation complete
[0005.170] list and configure display window
[0005.175] display console init completed
[0005.182] subnode volume_up is not found !
[0005.186] subnode back is not found !
[0005.190] subnode volume_down is not found !
[0005.194] subnode menu is not found !
[0005.198] Gpio keyboard init success
[0005.246] found decompressor handler: lz4-legacy
[0005.261] decompressing blob (type 1)...
[0005.328] load_bmp_blob: panelresolution=480 type=0
[0005.378] decompressor handler not found
[0005.382] load_firmware_blob: Firmware blob loaded, entries=2
[0005.388] XUSB blob version 0 size 124416 @ 0x92df928c
[0005.394] -------> se_aes_verify_sbk_clear: 747
[0005.398] se_aes_verify_sbk_clear: Error
[0005.402] SE operation failed
[0005.405] bl_battery_charging: connected to external power supply
[0005.421] device_query_partition_size: failed to open partition sdmmc3_user:MSC !
[0005.428] MSC Partition not found
[0005.438] device_query_partition_size: failed to open partition sdmmc3_user:USP !
[0005.445] USP partition read failed!
[0005.449] blob_init: blob-partition USP header read failed
[0005.454] android_boot Unable to update recovery partition
[0005.460] kfs_getpartname: name = LNX
[0005.463] Loading kernel from LNX
[0005.558] load kernel from storage
[0005.567] decompressor handler not found
[0005.602] Successfully loaded kernel and ramdisk images
[0005.607] board ID = D78, board SKU = 2
[0005.611] load_bmp_blob: panelresolution=480 type=0
[0005.685] display bmp image done
[0005.688] NCK carveout not present
[0005.691] Skipping dts_overrides
[0005.695] NCK carveout not present
[0005.704] Find /i2c@7000c000's alias i2c0
[0005.708] get eeprom at 1-a0, size 256, type 0
[0005.717] Find /i2c@7000c500's alias i2c2
[0005.721] get eeprom at 3-a0, size 256, type 0
[0005.725] get eeprom at 3-ae, size 256, type 0
[0005.730] pm_ids_update: Updating 1,a0, size 256, type 0
[0005.735] I2C slave not started
[0005.738] I2C write failed
[0005.741] Writing offset failed
[0005.744] eeprom_init: EEPROM read failed
[0005.748] pm_ids_update: eeprom init failed
[0005.752] pm_ids_update: Updating 3,a0, size 256, type 0
[0005.782] pm_ids_update: The pm board id is 3448-0002-400
[0005.789] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0005.797] pm_ids_update: pm id update successful
[0005.802] pm_ids_update: Updating 3,ae, size 256, type 0
[0005.807] I2C slave not started
[0005.810] I2C write failed
[0005.813] Writing offset failed
[0005.816] eeprom_init: EEPROM read failed
[0005.820] pm_ids_update: eeprom init failed
[0005.850] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0005.855] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0005.863] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0005.869] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0005.877] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3e:8b:1b
[0005.884] Plugin Manager: Parse ODM data 0x000a4000
[0005.896] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0005.905] Add serial number:1421621010071 as DT property
[0005.914] "bpmp" doesn't exist, creating 
[0005.919] Updated bpmp info to DTB
[0005.924] Updated initrd info to DTB
[0005.927] "proc-board" doesn't exist, creating 
[0005.934] Updated board info to DTB
[0005.937] "pmu-board" doesn't exist, creating 
[0005.943] Updated board info to DTB
[0005.946] "display-board" doesn't exist, creating 
[0005.952] Updated board info to DTB
[0005.956] "reset" doesn't exist, creating 
[0005.960] Updated reset info to DTB
[0005.964] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92cb4000 is_hdmi_initialised=1 
[0006.003] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 
[0006.008] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 
[0006.025] Updated bootarg info to DTB
[0006.029] Adding uuid 00000001643146c108000000130600c0 to DT
[0006.034] Adding eks info 0 to DT
[0006.040] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0006.046] Updated memory info to DTB
[0006.054] set vdd_core voltage to 1075 mv
[0006.058] setting 'vdd-core' regulator to 1075000 micro volts
[0006.064] Found secure-pmc; disable BPMP


U-Boot 2020.04-g6b630d64fd (Feb 19 2021 - 08:37:46 -0800)

SoC: tegra210
Model: NVIDIA Jetson Nano Developer Kit
Board: NVIDIA P3450-0000
DRAM:  4 GiB
MMC:   sdhci@700b0000: 1, sdhci@700b0600: 0
Loading Environment from SPI Flash... *** Warning - spi_flash_probe_bus_cs() failed, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  2  0
Tegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@700b0000: 1, sdhci@700b0600: yegra210 (P3450-0000) #  sdhci@7