ethan@ethan:~$ minicom

Welcome to minicom 2.7.1

OPTIONS: I18n
Compiled on Aug 13 2017, 15:25:34.
Port /dev/ttyUSB3, 15:58:56

Press CTRL-A Z for help on special keys

��
[0357.890] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fus.
[0357.899] I> MB1 (prd-version: 1.5.1.3-t194-41334769-d2a21c57)
[0357.904] I> Boot-mode: Platform RCM
[0357.907] I> Chip revision : A02P
[0357.910] I> Bootrom patch version : 15 (correctly patched)
[0357.916] I> ATE fuse revision : 0x200
[0357.919] I> Ram repair fuse : 0x0
[0357.922] I> Ram Code : 0x2
[0357.925] I> rst_source : 0xb
[0357.928] I> rst_level : 0x1
[0357.931] I> USB configuration success
[0359.922] I> mb2 image downloaded
[0359.931] I> Recovery boot mode 0
[0359.934] I> Boot-device: eMMC
[0359.939] I> UPHY full init done
[0359.943] I> MB1 done

[0359.949] W> Profiler not initialized
[0359.952] I> Welcome to MB2(TBoot-BPMP) Applet (version: 00.00.2018.32-mobile-72b55d98)
[0359.960] W> Profiler not initialized
[0359.964] I> DMA Heap @ [0x40020000 - 0x40065800]
[0359.968] I> Default Heap @ [0xd486400 - 0xd48a400]
[0359.973] W> Profiler not initialized
[0359.976] W> Profiler not initialized
[0359.980] E> DEVICE_PROD: Invalid value data = 0, size = 0.
[0359.985] W> device prod register failed
[0359.989] W> Profiler not initialized
[0360.014] I> sdmmc DDR50 mode
[0360.018] I> No supported QSPI flash found
[0360.022] E> QSPI Flash: Insufficient flash size (0 MB)
[0360.027] I> QSPI Flash is not present.
[0360.078] E> Link startup dme_set failed
[0360.082] E> UFS initialization failed
[0360.085] I> UFS is not present
[0360.088] W> Profiler not initialized
[0360.096] I> Found 17 partitions in SDMMC_BOOT (instance 3)
[0360.105] I> Found 42 partitions in SDMMC_USER (instance 3)
[0360.110] W> Profiler not initialized
[0360.114] W> Profiler not initialized
[0360.117] W> Profiler not initialized
[0360.121] I> Entering 3p server
[0360.124] I> USB configuration success
[0360.953] I> Populate eeprom info
[0360.958] I> Populate eeprom info for module cvm
[0360.998] I> Rebooting : reboot-recovery


[036��
[0087.886] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fus.
[0087.894] I> MB1 (prd-version: 1.5.1.3-t194-41334769-d2a21c57)
[0087.899] I> Boot-mode: RCM
[0087.902] I> Chip revision : A02P
[0087.905] I> Bootrom patch version : 15 (correctly patched)
[0087.910] I> ATE fuse revision : 0x200
[0087.914] I> Ram repair fuse : 0x0
[0087.917] I> Ram Code : 0x2
[0087.919] I> rst_source : 0xb
[0087.922] I> rst_level : 0x1
[0087.926] I> USB configuration success
[0089.891] I> bct_bootrom image downloaded
[0089.899] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT.
[0089.906] I> Temperature = 36000
[0089.909] W> Skipping boost for clk: BPMP_CPU_NIC
[0089.913] W> Skipping boost for clk: BPMP_APB
[0089.917] W> Skipping boost for clk: AXI_CBB
[0089.921] W> Skipping boost for clk: AON_CPU_NIC
[0089.925] W> Skipping boost for clk: CAN1
[0089.929] W> Skipping boost for clk: CAN2
[0089.933] I> Boot-device: eMMC
[0089.936] I> Boot-device: eMMC
[0089.939] I> bct_mb1 image downloaded
[0089.949] I> ECC region[0]: Start:0x0, End:0x0
[0089.953] I> ECC region[1]: Start:0x0, End:0x0
[0089.957] I> ECC region[2]: Start:0x0, End:0x0
[0089.961] I> ECC region[3]: Start:0x0, End:0x0
[0089.965] I> ECC region[4]: Start:0x0, End:0x0
[0089.969] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000
[0089.975] I> Non-ECC region[1]: Start:0x0, End:0x0
[0089.980] I> Non-ECC region[2]: Start:0x0, End:0x0
[0089.984] I> Non-ECC region[3]: Start:0x0, End:0x0
[0089.989] I> Non-ECC region[4]: Start:0x0, End:0x0
[0089.995] E> FAILED: Thermal config
[0090.002] E> FAILED: MEMIO rail config
[0090.020] E> Task 50 failed (err: 0x7979061c)
[0090.024] E> Top caller module: ALIASCHECKER, error module: ALIASCHECKER, reason: 0x1c, aux_in6
[0090.033] I> MB1(1.5.1.3-t194-41334769-d2a21c57) BIT boot status dump :
000000000001111111111000011111111111111001100011111000000000000000000000000000000000000000000000
[0090.063] I> Reset to recovery mode