[0000.066] I> MB1 (version: 0.11.0.0-t234-54845784-7fb1fa27) [0000.072] I> t234-A01-0-Silicon (0x12347) Prod [0000.076] I> Boot-mode : Coldboot [0000.079] I> Emulation: [0000.081] I> Entry timestamp: 0x00000000 [0000.085] I> last_boot_error: 0x0 [0000.088] I> BR-BCT: preprod_dev_sign: 0 [0000.092] I> rst_source: 0x0, rst_level: 0x0 [0000.096] I> Task: Clocks enable (0x50011b9d) [0000.100] I> Task: Crypto init (0x50018df5) [0000.104] I> Task: Secure debug controls (0x5000c76d) [0000.109] E> Error: ECID of check failed!! [0000.113] E> Error: ECID of check failed!! [0000.117] E> Error: ECID of check failed!! [0000.121] E> Error: ECID of check failed!! [0000.125] I> Task: Program NV master stream id (0x5000c725) [0000.130] I> Task: Verify boot mode (0xd482021) [0000.139] I> Task: Alias fuses (0x5000ecd5) [0000.143] E> FUSE_ALIAS: Fuse alias on production fused part is not supported. [0000.150] I> Task: 0x5000e911 [0000.153] I> FUSE_OPT_CCPLEX_CLUSTER_DISABLE = 0x00000000 [0000.158] I> FUSE_OPT_GPC_DISABLE = 0x00000000 [0000.162] I> FUSE_OPT_DLA_DISABLE = 0x00000000 [0000.167] I> FUSE_OPT_EMC_DISABLE = 0x00000000 [0000.171] I> FUSE_BOOTROM_PATCH_VERSION = 0x7 [0000.175] I> FUSE_PSCROM_PATCH_VERSION = 0x7 [0000.179] I> FUSE_OPT_ADC_CAL_FUSE_REV = 0x2 [0000.183] I> FUSE_SKU_INFO_0 = 0xd0 [0000.187] I> FUSE_OPT_SAMPLE_TYPE_0 = 0x3 PS [0000.191] I> FUSE_PACKAGE_INFO_0 = 0x2 [0000.194] I> SKU: Perfect F0 [0000.197] I> Task: Voltage monitor (0x50011ba5) [0000.201] I> VMON: Vmon re-calibration and fine tuning done [0000.207] I> Task: Blockdev init (0x500157e1) [0000.211] I> Task: UPHY init (0x5001b42d) [0000.215] E> UPHY: UPHY lane info table is empty in MB1 BCT. [0000.221] I> Task: Boot device init (0x5000d6a9) [0000.225] E> Adding eMMC storage modules [0000.229] I> Boot-device: QSPI (instance: 0) [0000.233] I> qspi flash params source = mb1bct [0000.238] I> Qspi clock source : pllc_out0 [0000.242] I> QSPI-0l initialized successfully [0000.246] I> Task: TSC init (0x5001c7e1) [0000.250] I> Task: Enable WDT 5th expiry (0x5001d27d) [0000.255] I> Task: Disable WDT globally (0x5001d2b9) [0000.260] I> Task: I2C register (0x50000a09) [0000.264] I> Task: Reset FSI (0x50011ba1) [0000.268] I> Task: Pinmux init (0x50010e95) [0000.272] I> Task: Prod config init (0x50011075) [0000.276] I> Task: Pad voltage init (0x50010f85) [0000.281] I> Task: Prod init (0x50011119) [0000.285] I> Task: Thermal check (0x5001121d) [0000.289] I> max_chip_limit = 115 [0000.292] I> min_chip_limit = -30 [0000.305] I> max temp read = 27 [0000.308] I> min temp read = 26 [0000.311] I> Task: Common rail init (0x50011695) [0000.316] W> Thermal config not found in BCT [0000.320] W> Generic i2c config not found in BCT [0000.325] > DEVICE_PROD: module = 13, instance = 4 not found in device prod. [0000.333] W> MEMIO rail config not found in BCT [0000.338] I> Task: Mem clock src (0x5000f6b9) [0000.342] I> Task: BR PMIC seq (0x50011711) [0000.346] I> Task: Misc. board config (0x500116ed) [0000.350] W> Platform config not found in BCT [0000.355] I> Task: Load membct (0x5000f5d5) [0000.359] I> RAM_CODE 0x4000401 [0000.362] I> Loading MEM-BCT to SysRAM [0000.365] I> Scratch RSV109: 0x00000001 active chain: 0 [0000.371] I> Slot: 0 [0000.373] I> Binary[0] block-0 (partition size: 0x40000) [0000.378] I> get_binary_info: Binary name: MEM-BCT-0 [0000.383] I> Size of crypto header is 8192 [0000.387] I> BCH load address is : 0x40050000 [0000.391] I> Size of crypto header is 8192 [0000.395] I> BCH of MEM-BCT-0 read from storage [0000.399] I> BCH address is : 0x40050000 [0000.403] I> MEM-BCT-0 header integrity check is success [0000.408] I> Binary magic in BCH component 0 is MEM0 [0000.413] I> component binary type is 0 [0000.417] I> MEM-BCT-0 binary is read from storage [0000.422] I> MEM-BCT-0 binary integrity check is success [0000.427] I> Binary MEM-BCT-0 loaded successfully at 0x40040000 (0xe580) [0000.438] I> RAM_CODE 0x4000401 [0000.442] I> Task: Save mem-bct info (0x50011d59) [0000.446] I> Task: SDRAM params override (0x50010c79) [0000.451] I> Task: Carveout allocate (0x50011da5) [0000.456] I> RCM blob carveout will not be allocated [0000.461] I> ECC region[0]: Start:0x0, End:0x0 [0000.465] I> ECC region[1]: Start:0x0, End:0x0 [0000.469] I> ECC region[2]: Start:0x0, End:0x0 [0000.473] I> ECC region[3]: Start:0x0, End:0x0 [0000.478] I> ECC region[4]: Start:0x0, End:0x0 [0000.482] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.488] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.492] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.497] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.502] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.508] I> allocated(CO:51) base:0x80000000 size:0x8000000 align: 0x200000 [0000.515] I> allocated(CO:44) base:0xd6000000 size:0x2a000000 align: 0x100000 [0000.522] I> allocated(CO:31) base:0xce000000 size:0x8000000 align: 0x100000 [0000.529] I> allocated(CO:39) base:0xc8000000 size:0x6000000 align: 0x200000 [0000.536] I> allocated(CO:20) base:0xc6000000 size:0x2000000 align: 0x2000000 [0000.543] I> allocated(CO:24) base:0xc4000000 size:0x2000000 align: 0x2000000 [0000.550] I> allocated(CO:28) base:0xc2000000 size:0x2000000 align: 0x2000000 [0000.557] I> allocated(CO:29) base:0xc0000000 size:0x2000000 align: 0x2000000 [0000.564] I> allocated(CO:41) base:0xbf000000 size:0x1000000 align: 0x100000 [0000.571] I> allocated(CO:43) base:0xbe000000 size:0x1000000 align: 0x200000 [0000.578] I> allocated(CO:02) base:0xbd800000 size:0x800000 align: 0x800000 [0000.585] I> allocated(CO:03) base:0xbd000000 size:0x800000 align: 0x800000 [0000.592] I> allocated(CO:06) base:0xbc800000 size:0x800000 align: 0x800000 [0000.599] I> allocated(CO:10) base:0xbc000000 size:0x800000 align: 0x800000 [0000.605] I> allocated(CO:56) base:0xbb800000 size:0x800000 align: 0x200000 [0000.612] I> allocated(CO:07) base:0xbb400000 size:0x400000 align: 0x400000 [0000.619] I> allocated(CO:22) base:0xbb000000 size:0x400000 align: 0x400000 [0000.626] I> allocated(CO:33) base:0xbac00000 size:0x400000 align: 0x200000 [0000.633] I> allocated(CO:47) base:0xba800000 size:0x400000 align: 0x200000 [0000.640] I> allocated(CO:01) base:0xba700000 size:0x100000 align: 0x100000 [0000.646] I> allocated(CO:04) base:0xba600000 size:0x100000 align: 0x100000 [0000.653] I> allocated(CO:05) base:0xba500000 size:0x100000 align: 0x100000 [0000.660] I> allocated(CO:08) base:0xba400000 size:0x100000 align: 0x100000 [0000.667] I> allocated(CO:09) base:0xba300000 size:0x100000 align: 0x100000 [0000.674] I> allocated(CO:15) base:0xba200000 size:0x100000 align: 0x100000 [0000.681] I> allocated(CO:17) base:0xba100000 size:0x100000 align: 0x100000 [0000.687] I> allocated(CO:23) base:0xba000000 size:0x100000 align: 0x100000 [0000.694] I> allocated(CO:27) base:0xb9f00000 size:0x100000 align: 0x100000 [0000.701] I> allocated(CO:42) base:0xb9e00000 size:0x100000 align: 0x100000 [0000.708] I> allocated(CO:54) base:0xb9d80000 size:0x80000 align: 0x80000 [0000.715] I> allocated(CO:26) base:0xb9d40000 size:0x40000 align: 0x2000 [0000.721] I> allocated(CO:48) base:0xb9d20000 size:0x20000 align: 0x10000 [0000.728] I> allocated(CO:34) base:0xb9d10000 size:0x10000 align: 0x10000 [0000.734] I> allocated(CO:35) base:0xb9d00000 size:0x10000 align: 0x10000 [0000.741] I> allocated(CO:49) base:0xb9cf0000 size:0x10000 align: 0x10000 [0000.748] I> allocated(CO:50) base:0xb9ce0000 size:0x10000 align: 0x10000 [0000.754] I> allocated(CO:52) base:0xb9cd0000 size:0x10000 align: 0x10000 [0000.761] I> Task: SDRAM init (0x5000f6bd) [0000.767] I> SDRAM-params @ 0xd485000 [0000.771] I> MSS code-drop: NvBootSdramInit [0000.775] I> MSS CAR: PLLM/HUB programming for MemoryType: 4 and MemBctRevision: 8 [0000.782] I> MSS CAR: Init PLLM [0000.785] I> MSS CAR: Init PLLHUB [0000.796] I> mb1_sdram_init Done ! [0000.799] I> SDRAM Size in Total 800000000 [0000.803] I> SDRAM test pass [0000.806] I> Task: Dram ecc scrub (0x5000f2c9) [0000.810] I> Task: DRAM alias check (0x50010c71) [0001.027] I> Task: Register checker (0x50010c75) [0001.035] I> Task: Enable clock-mon (0x5001c301) [0001.052] I> FMON: Fmon re-programmed in mb1 [0001.057] I> Task: Mapper init (0x5001a0d5) [0001.062] I> Task: SC7 Context Init (0x5001cacd) [0001.068] I> NV_SC7 Context addr: 0xa0000000 [0001.073] I> Task: CCPLEX IST init (0x5000ce75) [0001.079] I> Task: CPU WP0 (0x5000c2c9) [0001.085] I> Loading MCE [0001.087] I> Scratch RSV109: 0x00000001 active chain: 0 [0001.093] I> Slot: 0 [0001.096] I> Binary[8] block-0 (partition size: 0x80000) [0001.102] I> get_binary_info: Binary name: MCE [0001.106] I> Size of crypto header is 8192 [0001.111] I> BCH load address is : 0x4003e000 [0001.116] I> Size of crypto header is 8192 [0001.121] I> BCH of MCE read from storage [0001.125] I> BCH address is : 0x4003e000 [0001.131] I> MCE header integrity check is success [0001.136] I> Binary magic in BCH component 0 is MTSM [0001.141] I> component binary type is 8 [0001.145] I> Size of crypto header is 8192 [0001.152] I> MCE binary is read from storage [0001.157] I> MCE binary integrity check is success [0001.163] I> Binary MCE loaded successfully at 0x40000000 (0x29e90) [0001.170] I> Size of crypto header is 8192 [0001.182] I> Size of crypto header is 8192 [0001.186] I> Sending WP0 mailbox command to PSC [0001.199] I> Task: MB1 fixed firewalls (0x5001b1bd) [0001.211] I> Task: Load bpmp-fw (0x5001b311) [0001.216] I> Scratch RSV109: 0x00000001 active chain: 0 [0001.222] I> Slot: 0 [0001.224] I> Binary[15] block-0 (partition size: 0x100000) [0001.231] I> get_binary_info: Binary name: BPMP_FW [0001.236] I> Size of crypto header is 8192 [0001.240] I> BCH load address is : 0x807fe000 [0001.246] I> Size of crypto header is 8192 [0001.251] I> BCH of BPMP_FW read from storage [0001.255] I> BCH address is : 0x807fe000 [0001.261] I> BPMP_FW header integrity check is success [0001.266] I> Binary magic in BCH component 0 is BPMF [0001.272] I> component binary type is 15 [0001.276] I> Size of crypto header is 8192 [0001.291] I> BPMP_FW binary is read from storage [0001.298] I> BPMP_FW binary integrity check is success [0001.304] I> Binary BPMP_FW loaded successfully at 0x80000000 (0xf3940) [0001.312] I> Scratch RSV109: 0x00000001 active chain: 0 [0001.318] I> Slot: 0 [0001.320] I> Binary[16] block-0 (partition size: 0x100000) [0001.326] I> get_binary_info: Binary name: BPMP_FW_DTB [0001.332] I> Size of crypto header is 8192 [0001.336] I> BCH load address is : 0x807fc000 [0001.342] I> Size of crypto header is 8192 [0001.347] I> BCH of BPMP_FW_DTB read from storage [0001.352] I> BCH address is : 0x807fc000 [0001.357] I> BPMP_FW_DTB header integrity check is success [0001.363] I> Binary magic in BCH component 0 is BPMD [0001.369] I> component binary type is 16 [0001.373] I> Size of crypto header is 8192 [0001.379] I> BPMP_FW_DTB binary is read from storage [0001.385] I> BPMP_FW_DTB binary integrity check is success [0001.391] I> Binary BPMP_FW_DTB loaded successfully at 0x807dbc00 (0x20380) [0001.399] I> Program IPC carveouts [0001.405] I> Task: Load psc-fw (0x5001b3b9) [0001.411] I> Scratch RSV109: 0x00000001 active chain: 0 [0001.416] I> Slot: 0 [0001.419] I> Binary[17] block-0 (partition size: 0x80000) [0001.425] I> get_binary_info: Binary name: PSC_FW [0001.430] I> Size of crypto header is 8192 [0001.435] I> BCH load address is : 0x803fe000 [0001.440] I> Size of crypto header is 8192 [0001.445] I> BCH of PSC_FW read from storage [0001.449] I> BCH address is : 0x803fe000 [0001.455] I> PSC_FW header integrity check is success [0001.460] I> Binary magic in BCH component 0 is PFWP [0001.466] I> component binary type is 17 [0001.470] I> Size of crypto header is 8192 [0001.478] I> PSC_FW binary is read from storage [0001.484] I> PSC_FW binary integrity check is success [0001.490] I> Binary PSC_FW loaded successfully at 0x80000000 (0x57800) [0001.498] I> Task: Load nvdec-fw (0x5001c05d) [0001.504] I> Scratch RSV109: 0x00000001 active chain: 0 [0001.510] I> Slot: 0 [0001.512] I> Binary[7] block-0 (partition size: 0x100000) [0001.518] I> get_binary_info: Binary name: NVDEC [0001.523] I> Size of crypto header is 8192 [0001.528] I> BCH load address is : 0x800fe000 [0001.533] I> Size of crypto header is 8192 [0001.538] I> BCH of NVDEC read from storage [0001.543] I> BCH address is : 0x800fe000 [0001.548] I> NVDEC header integrity check is success [0001.553] I> Binary magic in BCH component 0 is NDEC [0001.559] I> component binary type is 7 [0001.563] I> Size of crypto header is 8192 [0001.570] I> NVDEC binary is read from storage [0001.575] I> NVDEC binary integrity check is success [0001.581] I> Binary NVDEC loaded successfully at 0x80000000 (0x35000) [0001.593] I> Task: Load tsec-fw (0x5001c249) [0001.598] I> TSEC-FW load support not enabled [0001.603] I> Task: TZDRAM setup (0x50012515) [0001.608] I> Task: SC7 context save (0x5001cbd1) [0001.614] I> NV_SC7 Context addr: 0xa0000000 [0001.620] I> Scratch RSV109: 0x00000001 active chain: 0 [0001.626] I> Slot: 0 [0001.628] I> Binary[13] block-0 (partition size: 0x20000) [0001.634] I> get_binary_info: Binary name: SC7-FW [0001.640] I> Size of crypto header is 8192 [0001.644] I> Size of crypto header is 8192 [0001.649] I> BCH load address is : 0xa0002000 [0001.654] I> Size of crypto header is 8192 [0001.659] I> BCH of SC7-FW read from storage [0001.664] I> BCH address is : 0xa0002000 [0001.669] I> SC7-FW header integrity check is success [0001.675] I> Binary magic in BCH component 0 is WB0B [0001.680] I> component binary type is 13 [0001.684] I> Size of crypto header is 8192 [0001.689] I> SC7-FW binary is read from storage [0001.695] I> SC7-FW binary integrity check is success [0001.700] I> Binary SC7-FW loaded successfully at 0xa0004000 (0xa4e0) [0001.708] I> Scratch RSV109: 0x00000001 active chain: 0 [0001.714] I> Slot: 0 [0001.716] I> Binary[22] block-0 (partition size: 0x30000) [0001.723] I> get_binary_info: Binary name: PSC_RF [0001.728] I> Size of crypto header is 8192 [0001.732] I> Size of crypto header is 8192 [0001.737] I> BCH load address is : 0xa000e4e0 [0001.742] I> Size of crypto header is 8192 [0001.747] I> BCH of PSC_RF read from storage [0001.752] I> BCH address is : 0xa000e4e0 [0001.757] I> PSC_RF header integrity check is success [0001.763] I> Binary magic in BCH component 0 is PSCR [0001.768] I> component binary type is 22 [0001.772] I> Size of crypto header is 8192 [0001.778] I> PSC_RF binary is read from storage [0001.784] I> PSC_RF binary integrity check is success [0001.789] I> Binary PSC_RF loaded successfully at 0xa00104e0 (0x1af70) [0001.808] I> Scratch RSV109: 0x00000001 active chain: 0 [0001.814] I> Slot: 0 [0001.816] I> Binary[14] block-0 (partition size: 0x20000) [0001.822] I> get_binary_info: Binary name: MB2_RF [0001.828] I> Size of crypto header is 8192 [0001.832] I> Size of crypto header is 8192 [0001.837] I> BCH load address is : 0xa008c020 [0001.842] I> Size of crypto header is 8192 [0001.847] I> BCH of MB2_RF read from storage [0001.852] I> BCH address is : 0xa008c020 [0001.857] I> MB2_RF header integrity check is success [0001.863] I> Binary magic in BCH component 0 is MB2R [0001.868] I> component binary type is 14 [0001.872] I> Size of crypto header is 8192 [0001.878] I> MB2_RF binary is read from storage [0001.883] I> MB2_RF binary integrity check is success [0001.888] I> Binary MB2_RF loaded successfully at 0xa008e020 (0xd360) [0001.897] E> FUSE_ALIAS: Fuse alias on production fused part is not supported. [0001.905] I> SC7 context fuse-bypass data is empty [0001.910] I> SC7 context save done [0001.914] I> Task: Load MB2/Applet/FSKP (0x5001c305) [0001.920] I> Loading MB2 [0001.923] I> Scratch RSV109: 0x00000001 active chain: 0 [0001.929] I> Slot: 0 [0001.931] I> Binary[6] block-0 (partition size: 0x70000) [0001.937] I> get_binary_info: Binary name: MB2 [0001.942] I> Size of crypto header is 8192 [0001.947] I> BCH load address is : 0x8007e000 [0001.952] I> Size of crypto header is 8192 [0001.957] I> BCH of MB2 read from storage [0001.961] I> BCH address is : 0x8007e000 [0001.967] I> MB2 header integrity check is success [0001.972] I> Binary magic in BCH component 0 is MB2B [0001.977] I> component binary type is 6 [0001.981] I> Size of crypto header is 8192 [0001.991] I> MB2 binary is read from storage [0001.997] I> MB2 binary integrity check is success [0002.002] I> Binary MB2 loaded successfully at 0x80000000 (0x69940) [0002.010] I> Task: Prepare MB2 params (0x5001c3d5) [0002.017] I> MB2-params @ 0x40060000 [0002.024] I> BR-BCT Boot Chain Fields [0002.028] I> u32_non_gpio_select_boot_chain : 0 [0002.033] I> u32_num_boot_chains : 2 [0002.038] I> bf_bl_gpio_select_boot_chain_1b : 0 [0002.043] I> Task: Dram ecc test (0x5000f379) [0002.049] I> Task: Misc NV security settings (0x5000ca35) [0002.056] I> NVDEC sticky bits programming done [0002.060] I> Task: GPIO interrupt map (0x50011a61) [0002.067] I> Task: Disable/Reload WDT (0x5001d2e9) [0002.073] I> Programmed SLCG global override := 0x0 [0002.078] I> MB1: MSS reconfig completed I> MB2 (version: 0.0.0.0-t234-54845784-e8d12f8b) I> t234-A01-0-Silicon (0x12347) I> Boot-mode : Coldboot I> Emulation: I> Entry timestamp: 0x0020614a I> Regular heap: [base:0x40040000, size:0x10000] I> DMA heap: [base:0xbb800000, size:0x800000] I> Task: Enable hot-plug capability (0x5001aed8) I> Task: Set blob address (0x50001c70) I> Task: PSC mailbox init (0x5000e5e0) I> Task: Crypto init (0x50005abc) I> Task: I2C register (0x50001c5c) I> Task: Boot device init (0x50001d2c) I> Boot_device: QSPI_FLASH instance: 0 I> Qspi clock source : pllc_out0 I> QSPI-0l initialized successfully I> qspi flash-0 params source = MB2 params I> sdmmc-3 params source = MB2 params I> Task: Partition Manager Init (0x50001cf8) I> Found 57 partitions in QSPI_FLASH (instance 0) W> Cannot find any partition table for 00000003 > PARTITION_MANAGER: Failed to publish partition. I> Found 11 partitions in SDMMC_USER (instance 3) I> Task: Load and authenticate registered FWs (0x50012818) I> Task: Load AUXP FWs (0x5001aa7c) I> Successfully register SPE FW load task with MB2 loader I> Skipping SCE FW load I> Successfully register RCE FW load task with MB2 loader I> Successfully register DCE FW load task with MB2 loader I> Unpowergating APE I> Unpowergate done I> Successfully register APE FW load task with MB2 loader I> Skipping FSI FW load I> Successfully register XUSB FW load task with MB2 loader I> Scratch RSV109: 0x00000001 active chain: 0 I> Partition name: A_spe-fw I> Size of partition: 589824 I> Binary@ device:3/0 block-56320 (partition size: 0x90000), name: A_spe-fw E> Binary spe is not found in comp table I> Scratch RSV109: 0x00000001 active chain: 0 I> Partition name: A_rce-fw I> Size of partition: 1048576 I> Binary@ device:3/0 block-57472 (partition size: 0x100000), name: A_rce-fw E> Binary rce is not found in comp table I> spe: Authentication Finalize Done I> Binary spe loaded successfully at 0xba400000 I> Scratch RSV109: 0x00000001 active chain: 0 I> Partition name: A_dce-fw I> Size of partition: 9437184 I> Binary@ device:3/0 block-37888 (partition size: 0x900000), name: A_dce-fw E> Binary dce is not found in comp table I> rce: Authentication Finalize Done I> Binary rce loaded successfully at 0xba100000 I> Scratch RSV109: 0x00000001 active chain: 0 I> Partition name: A_adsp-fw I> Size of partition: 2097152 I> Binary@ device:3/0 block-59520 (partition size: 0x200000), name: A_adsp-fw E> Binary ape is not found in comp table I> dce: Authentication Finalize Done I> Binary dce loaded successfully at 0xc6000000 I> Scratch RSV109: 0x00000001 active chain: 0 I> Partition name: A_xusb-fw I> Size of partition: 262144 I> Binary@ device:3/0 block-10368 (partition size: 0x40000), name: A_xusb-fw E> Binary xusb is not found in comp table I> ape: Authentication Finalize Done I> Binary ape loaded successfully at 0xbb400000 I> xusb: Authentication Finalize Done I> Binary xusb loaded successfully at 0xba500000 I> Task: Carveout setup (0x50014018) I> Program remaining OEM carveouts I> Task: Restore XUSB sec (0x50001c30) I> Task: OEM firewalls (0x50017ee0) I> MB2-BCT Firewall data is empty I> Task: Unhalt AUXPs (0x5001ace4) I> Unhalting SPE.. I> Enabling combined UART spe: early_init vic initialized tsc initialized aon lic initialized spe: tag is 9f1f07bc2d4b6509c13554672acefaad spe: SafeRTOS v8.4 spe: init scheduler initialized aon hsp initialized tag initialized tcu initialized bpmp ipc initialized spe: late init cpu_nic clock initialized apb clock initialized pm initialized bpmp hsp initialized top1 hsp initialized ccplex ipc initialized spe: start scheduler I> Task: Trigger mailbox for PSC-BL1 exit (0x5000e660) I> Sending opcode 0x4d420802 to psc INFO: Entering psc_monitor_init! INFO: GSC22 BOM:0xbb000000 SIZE:0x400000 CLIENT_ACCESS1:00180000 INFO: PSCFW BUILD VERSION: a796142-39d6527-7490c54-dev INFI> Received ACK from psc O: mstatus:0xa00000808 INFO: Supervisor entry_poinI> Task: Start secure NOR provision (0x50010b3c) I> Task: Load FSI keyblob (0x5000ea28) I> Skipping FSI key blob copy I> Task: Enable FSITHERM (0x5000e5b4) t:c108c00 INFO: pllpsc is already locked. INFO: MONITOR: user task addr:0xbb022000, blob offset:0x00020000 I> Task: Unhalt AUXPs (0x5001acec) I> SCE unhalt skipped I> Unhalting RCE I> RCE unhalt successful I> DCE unhalt successful I> APE unhalt skipped I> FSI unhalt skipped I> Task: Load CPUBL (0x5000f7c4) I> Task: Load TOS (0x5000fe50) I> Task: Load and authenticate registered FWs (0x50012818)[ 2.438523] Camerbpmp: init bpmp: base binary md5 is f0425a554b39d571b1bbb5291283d946 bpmp: combined binary md5 is 43f75b5aad2b8e1992e4e049bafc8696 bpmp: firmware tag is 43 INFO: MONITOR: populated user images:16 INFO: mret to Supervisor! INFO: psc supervisor init. INFO: psc_irq_init... INFO: enter idle task. I> Scratch RSV109: 0x00000001 active chain: 0 I> Partition name: A_cpu-bootloader I> Size of partition: 3670016 I> Binary@ device:3/0 block-17920 (partition size: 0x380000), name: A_cpu-bootloader a-FW on t234-rce-safe started TCU early console enabled. f75b5aad2b8e1992e4-f0425a554b3 initialized vwdt initialized clk_mach_early initialized mail_early initialized fuse initialized vfrel initialized hwwdt initialized adc fmon_populate_monitors: found 199 monitors initialized fmon initialized mc initialized reset initialized uphy_early initialized emc_early 469 clocks registered initialized clk_mach initialized clk_cal_early initialized clk_mach_early_config initialized io_dpd initialized theE> Binary cpubl is not found in comp table rmal initialized soctherm initialized regime initialized i2c vrmon_dt_init: vrmon node not found vrmon_chk_boot_state: found 0 rail monitors initialized vrmon initialized regulator initialized avfs_clk_platform initialized powergate initialized dvs initialized clk_mach_config initialized pm initialized suspend initialized strap initialized emc initialized emc_mrq WARNING @ [platform/drivers/clk/clk-fwk/clk-cal.c]: aon_apb is not configured by BPMP-FW WARNING @ [platform/drivers/clk/clk-fwkI> Scratch RSV109: 0x00000001 active chain: 0 I> Partition name: A_secure-os I> Size of partition: 4194304 I> Binary@ device:3/0 block-25088 (partition /clk-cal.c]: aon_cpu_nic is not configured by BPMP-FW size: 0x400000), nameinitialized clk_cal initialized uphy_dt initialized uphy_mrq initialized uphy initialized pg_late initialized pg_mrq_init swdtimer_init: 0 reg polling s: A_secure-os tart w period 47 ms initialized swdtimer initialized hwwdt_E> Binary tos is not found in comp table late initialized bwmgr initializI> MB2-params @ 0x40060000 I> CPUBL-params @ 0xc2000000 ed thermal_host_trip initialized thermal_mrq initialized reset_mrq initialized mail_mrq initialized fmon_mrq initialized clk_mrq initialized avfs_mrq initialized i2c_mrq initialized tag_mrq initialized bwmgr_mrq initialized console_mrq initialized mrq missing prod DT calibration data for 199 fmons initialized clk_sync_fmon_post initialized clk_cal_late initialized noc_late initialized dbells initia[ 2.665393] Camera-FW on t234-rce-safe ready SHA1=ab261c6c (crt 16.253 ms,lized dmce initialized cvc initialized avfs_clk_mach_post initialized pm_post initialized avfs_clk_platform_post initialized cvc_late initialized rm initialized console_late initialized clk_mach_post initialized pg_post initialized regulator_post initialized profile initialized fuse_late initialized extras_post bpmp: init complete I> cpubl: Authentication Finalize Done I> Binary cpubl loaded successfully at 0xba800000 total boot 244.178 ms) I> tos: Authentication Finalize Done I> Binary tos loaded successfully at 0xbeee7000 DCE: FW Boot Done I> Task: Prepare TOS params (0x5000fdcc) I> Task: OEM SC7 context save (0x50010878) I> oem sc7 context saved I> Task: Disable MSS perf stats (0x5001ad78) I> Task: Program display sticky bits (0x5001acf4) I> Task: Storage device deinit (0x50001ca4) I> Task: SMMU init (0x5001a738) I> Task: Program CBB PCIE AMAP regions (0x500031dc) I> Task: Program GICv3 registers (0x5001ae18) I> Task: Audit firewall settings (0x5001816c) I> MB2 finished NOTICE: BL31: v2.5(release):ef8af0b99 NOTICE: BL31: Built : 20:58:00, May 16 2022 ERROR: Error initializing runtime service trusty_fast Jetson UEFI firmware (version r34.1-975eef6 built on 2022-05-16T20:58:45-07:00) ** WARNING: Test Key is used. ** ExtLinuxBoot: Failed to open file: \boot\initrd Not Found L4TLauncher: Unable to boot via extlinux: Not Found EFI stub: Booting Linux Kernel... EFI stub: Using DTB from configuration table EFI stub: Loaded initrd from LINUX_EFI_INITRD_MEDIA_GUID device path EFI stub: Exiting boot services and installing virtual address map... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd421] [ 0.000000] Linux version 5.10.65-tegra (buildbrain@mobile-u64-5414-d7000) (aarch64-buildroot-linux-gnu-gcc.br_real 2 [ 0.000000] OF: fdt: memory scan node memory@80000000, reg size 16, [ 0.000000] OF: fdt: - 80000000 , c0000000 [ 0.000000] Machine model: NVIDIA Orin Jetson-Small Developer Kit [ 0.000000] efi: EFI v2.70 by EDK II [ 0.000000] efi: RTPROP=0x8548b1898 SMBIOS=0xbabc0000 SMBIOS 3.0=0x853260000 MEMATTR=0x853173018 ESRT=0x8532b8218 RN [ 0.000000] efi: seeding entropy pool [ 0.000000] esrt: Reserving ESRT space from 0x00000008532b8218 to 0x00000008532b8250. [ 0.000000] Reserved memory: created CMA memory pool at 0x000000086b800000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] OF: reserved mem: initialized node fsi-carveout, compatible id nvidia,fsi-carveout [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000087fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x0000000087ffffff] [ 0.000000] node 0: [mem 0x0000000088000000-0x00000000b9ccffff] [ 0.000000] node 0: [mem 0x00000000ba800000-0x00000000ba9affff] [ 0.000000] node 0: [mem 0x00000000babb0000-0x00000000babcffff] [ 0.000000] node 0: [mem 0x00000000babd0000-0x00000000babfffff] [ 0.000000] node 0: [mem 0x00000000c2000000-0x00000000c3ffffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x000000084fffffff] [ 0.000000] node 0: [mem 0x0000000850000000-0x0000000851faffff] [ 0.000000] node 0: [mem 0x0000000851fb0000-0x0000000852cf0fff] [ 0.000000] node 0: [mem 0x0000000852cf1000-0x0000000852e52fff] [ 0.000000] node 0: [mem 0x0000000852e53000-0x0000000852edffff] [ 0.000000] node 0: [mem 0x0000000852ee0000-0x0000000852efffff] [ 0.000000] node 0: [mem 0x0000000852f00000-0x000000085317ffff] [ 0.000000] node 0: [mem 0x0000000853180000-0x000000085319ffff] [ 0.000000] node 0: [mem 0x00000008531a0000-0x00000008531fffff] [ 0.000000] node 0: [mem 0x0000000853200000-0x000000085320ffff] [ 0.000000] node 0: [mem 0x0000000853210000-0x000000085325ffff] [ 0.000000] node 0: [mem 0x0000000853260000-0x000000085326ffff] [ 0.000000] node 0: [mem 0x0000000853270000-0x0000000853ceffff] [ 0.000000] node 0: [mem 0x0000000853cf0000-0x0000000853f1ffff] [ 0.000000] node 0: [mem 0x0000000853f20000-0x0000000853fdffff] [ 0.000000] node 0: [mem 0x0000000853fe0000-0x000000085411ffff] [ 0.000000] node 0: [mem 0x0000000854120000-0x000000085418ffff] [ 0.000000] node 0: [mem 0x0000000854190000-0x000000085424ffff] [ 0.000000] node 0: [mem 0x0000000854250000-0x000000085425ffff] [ 0.000000] node 0: [mem 0x0000000854260000-0x00000008542fffff] [ 0.000000] node 0: [mem 0x0000000854300000-0x000000085434ffff] [ 0.000000] node 0: [mem 0x0000000854350000-0x000000085435ffff] [ 0.000000] node 0: [mem 0x0000000854360000-0x00000008543affff] [ 0.000000] node 0: [mem 0x00000008543b0000-0x000000085456ffff] [ 0.000000] node 0: [mem 0x0000000854570000-0x000000085457ffff] [ 0.000000] node 0: [mem 0x0000000854580000-0x000000085465ffff] [ 0.000000] node 0: [mem 0x0000000854660000-0x00000008546dffff] [ 0.000000] node 0: [mem 0x00000008546e0000-0x000000085477ffff] [ 0.000000] node 0: [mem 0x0000000854780000-0x000000085485ffff] [ 0.000000] node 0: [mem 0x0000000854860000-0x00000008548affff] [ 0.000000] node 0: [mem 0x00000008548b0000-0x000000085493ffff] [ 0.000000] node 0: [mem 0x0000000854940000-0x000000085498ffff] [ 0.000000] node 0: [mem 0x0000000854990000-0x00000008549affff] [ 0.000000] node 0: [mem 0x00000008549b0000-0x0000000854a4ffff] [ 0.000000] node 0: [mem 0x0000000854a50000-0x0000000854aaffff] [ 0.000000] node 0: [mem 0x0000000854ab0000-0x0000000854b9ffff] [ 0.000000] node 0: [mem 0x0000000854ba0000-0x000000085537ffff] [ 0.000000] node 0: [mem 0x0000000855380000-0x000000085555ffff] [ 0.000000] node 0: [mem 0x0000000855560000-0x000000087b8bffff] [ 0.000000] node 0: [mem 0x000000087b8c0000-0x000000087b90ffff] [ 0.000000] node 0: [mem 0x000000087b910000-0x000000087fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000087fffffff] [ 0.000000] On node 0, zone DMA: 304 pages in unavailable ranges [ 0.000000] On node 0, zone DMA: 80 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 31 pages/cpu s90008 r8192 d28776 u126976 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Virtualization Host Extensions [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] alternatives: patching kernel code [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 7983060 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 mminit_loglevel=4 console=ttyTCU0,1 [ 0.000000] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes, linear) [ 0.000000] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000a9cd0000-0x00000000b9cd0000] (256MB) [ 0.000000] Memory: 31083300K/32439104K available (18496K kernel code, 3214K rwdata, 7092K rodata, 3968K init, 1070K) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=12, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=12. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=12 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 960 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000f440000 [ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:608, num:70) [ 0.000000] GICv2m: range[mem 0x0f410000-0x0f41ffff], SPI[608:677] [ 0.000000] random: get_random_bytes called from start_kernel+0x378/0x4f4 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 31.25MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xe6a171046, max_idle_ns: 881590405314s [ 0.000002] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398046511088ns [ 0.000593] Console: colour dummy device 80x25 [ 0.000799] printk: console [tty0] enabled [ 0.000840] Calibrating delay loop (skipped), value calculated using timer frequency.. 62.50 BogoMIPS (lpj=125000) [ 0.000850] pid_max: default: 32768 minimum: 301 [ 0.000901] LSM: Security Framework initializing [ 0.000968] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.001017] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.002680] rcu: Hierarchical SRCU implementation. [ 0.002772] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.003124] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-5.10/arch/arm64/boot/dts/../../../../../../s [ 0.003134] DTB Build time: May 16 2022 21:09:35 [ 0.004189] Tegra Revision: A01 SKU: 0xd0 CPU Process: 0 SoC Process: 0 [ 0.004303] Remapping and enabling EFI services. [ 0.005467] smp: Bringing up secondary CPUs ... [ 0.005862] Detected PIPT I-cache on CPU1 [ 0.005897] GICv3: CPU1: found redistributor 100 region 0:0x000000000f460000 [ 0.005932] CPU1: Booted secondary processor 0x0000000100 [0x410fd421] [ 0.006288] Detected PIPT I-cache on CPU2 [ 0.006298] GICv3: CPU2: found redistributor 200 region 0:0x000000000f480000 [ 0.006312] CPU2: Booted secondary processor 0x0000000200 [0x410fd421] [ 0.006627] Detected PIPT I-cache on CPU3 [ 0.006636] GICv3: CPU3: found redistributor 300 region 0:0x000000000f4a0000 [ 0.006649] CPU3: Booted secondary processor 0x0000000300 [0x410fd421] [ 0.008974] Detected PIPT I-cache on CPU4 [ 0.008994] GICv3: CPU4: found redistributor 10000 region 0:0x000000000f4c0000 [ 0.009020] CPU4: Booted secondary processor 0x0000010000 [0x410fd421] [ 0.009393] Detected PIPT I-cache on CPU5 [ 0.009402] GICv3: CPU5: found redistributor 10100 region 0:0x000000000f4e0000 [ 0.009416] CPU5: Booted secondary processor 0x0000010100 [0x410fd421] [ 0.009752] Detected PIPT I-cache on CPU6 [ 0.009761] GICv3: CPU6: found redistributor 10200 region 0:0x000000000f500000 [ 0.009774] CPU6: Booted secondary processor 0x0000010200 [0x410fd421] [ 0.010122] Detected PIPT I-cache on CPU7 [ 0.010131] GICv3: CPU7: found redistributor 10300 region 0:0x000000000f520000 [ 0.010145] CPU7: Booted secondary processor 0x0000010300 [0x410fd421] [ 0.012481] Detected PIPT I-cache on CPU8 [ 0.012504] GICv3: CPU8: found redistributor 20000 region 0:0x000000000f540000 [ 0.012531] CPU8: Booted secondary processor 0x0000020000 [0x410fd421] [ 0.012900] Detected PIPT I-cache on CPU9 [ 0.012910] GICv3: CPU9: found redistributor 20100 region 0:0x000000000f560000 [ 0.012924] CPU9: Booted secondary processor 0x0000020100 [0x410fd421] [ 0.013271] Detected PIPT I-cache on CPU10 [ 0.013281] GICv3: CPU10: found redistributor 20200 region 0:0x000000000f580000 [ 0.013294] CPU10: Booted secondary processor 0x0000020200 [0x410fd421] [ 0.013636] Detected PIPT I-cache on CPU11 [ 0.013646] GICv3: CPU11: found redistributor 20300 region 0:0x000000000f5a0000 [ 0.013661] CPU11: Booted secondary processor 0x0000020300 [0x410fd421] [ 0.013716] smp: Brought up 1 node, 12 CPUs [ 0.013780] SMP: Total of 12 processors activated. [ 0.013784] CPU features: detected: Privileged Access Never [ 0.013787] CPU features: detected: LSE atomic instructions [ 0.013789] CPU features: detected: User Access Override [ 0.013792] CPU features: detected: 32-bit EL0 Support [ 0.013795] CPU features: detected: Common not Private translations [ 0.013798] CPU features: detected: RAS Extension Support [ 0.013800] CPU features: detected: Data cache clean to the PoU not required for I/D coherence [ 0.013804] CPU features: detected: CRC32 instructions [ 0.013806] CPU features: detected: Speculative Store Bypassing Safe (SSBS) [ 0.047515] CPU: All CPU(s) started at EL2 [ 0.049773] devtmpfs: initialized [ 0.058973] Registered cp15_barrier emulation handler [ 0.058987] Registered setend emulation handler [ 0.058993] KASLR enabled [ 0.059086] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.059098] futex hash table entries: 4096 (order: 6, 262144 bytes, linear) [ 0.060629] pinctrl core: initialized pinctrl subsystem [ 0.061071] SMBIOS 3.0.0 present. [ 0.061078] DMI: /, BIOS r34.1-975eef6 05/16/2022 [ 0.061326] NET: Registered protocol family 16 [ 0.062219] DMA: preallocated 4096 KiB GFP_KERNEL pool for atomic allocations [ 0.062426] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.062619] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.062659] audit: initializing netlink subsys (disabled) [ 0.062759] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1 [ 0.063424] printk: console [ramoops-1] enabled [ 0.063432] pstore: Registered ramoops as persistent store backend [ 0.063438] ramoops: using 0x200000@0xba9b0000, ecc: 0 [ 0.063612] thermal_sys: Registered thermal governor 'step_wise' [ 0.063613] thermal_sys: Registered thermal governor 'power_allocator' [ 0.063619] thermal_sys: Registered thermal governor 'pid_thermal_gov' [ 0.065044] cpuidle: using governor menu [ 0.065152] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.065264] ASID allocator initialised with 65536 entries [ 0.065337] Serial: AMBA PL011 UART driver [ 0.066521] tegra234_mc_sid_probe(): tegra234 mc-sid probe successful [ 0.066542] Tegra reboot handler registered. [ 0.066602] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-5.10/arch/arm64/boot/dts/../../../../../../s [ 0.066611] DTB Build time: May 16 2022 21:09:35 [ 0.080628] mc: mapped MMIO address: 0x(____ptrval____) -> 0x2c10000 [ 0.080645] mc: mapped MMIO address: 0x(____ptrval____) -> 0x2c20000 [ 0.080657] mc: mapped MMIO address: 0x(____ptrval____) -> 0x2c30000 [ 0.080667] mc: mapped MMIO address: 0x(____ptrval____) -> 0x2c40000 [ 0.080676] mc: mapped MMIO address: 0x(____ptrval____) -> 0x2c50000 [ 0.080687] mc: mapped MMIO address: 0x(____ptrval____) -> 0x2b80000 [ 0.080695] mc: mapped MMIO address: 0x(____ptrval____) -> 0x2b90000 [ 0.080704] mc: mapped MMIO address: 0x(____ptrval____) -> 0x2ba0000 [ 0.080712] mc: mapped MMIO address: 0x(____ptrval____) -> 0x2bb0000 [ 0.080720] mc: mapped MMIO address: 0x(____ptrval____) -> 0x1700000 [ 0.080729] mc: mapped MMIO address: 0x(____ptrval____) -> 0x1710000 [ 0.080738] mc: mapped MMIO address: 0x(____ptrval____) -> 0x1720000 [ 0.080746] mc: mapped MMIO address: 0x(____ptrval____) -> 0x1730000 [ 0.080754] mc: mapped MMIO address: 0x(____ptrval____) -> 0x1740000 [ 0.080762] mc: mapped MMIO address: 0x(____ptrval____) -> 0x1750000 [ 0.080770] mc: mapped MMIO address: 0x(____ptrval____) -> 0x1760000 [ 0.080778] mc: mapped MMIO address: 0x(____ptrval____) -> 0x1770000 [ 0.080789] nv-tegra-mc 2c10000.mc: No mssnvlink node [ 0.080810] mc-err: mcerr ops are set to t23x [ 0.081093] tegra23x-cbb 13a00000.cbb-en: secure_irq = 21 [ 0.081149] tegra23x-cbb c600000.aon-en: secure_irq = 22 [ 0.081188] tegra23x-cbb de00000.dce-en: secure_irq = 23 [ 0.081225] tegra23x-cbb be00000.rce-en: secure_irq = 24 [ 0.081260] tegra23x-cbb b600000.sce-en: secure_irq = 25 [ 0.084938] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.084949] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.084955] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.084960] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.086535] ACPI: Interpreter disabled. [ 0.087573] vdd-av1v1-hub: supplied by vdd-5v-sys [ 0.087714] vbusA-cvb: supplied by vdd-5v-sys [ 0.087806] vbusB-cvb: supplied by vdd-5v-sys [ 0.087910] vdd-usbc1-vbus: supplied by vdd-5v-sys [ 0.088001] vdd-usbc2-vbus: supplied by vdd-5v-sys [ 0.088296] iommu: Default domain type: Translated [ 0.088335] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.088480] SCSI subsystem initialized [ 0.088543] usbcore: registered new interface driver usbfs [ 0.088556] usbcore: registered new interface driver hub [ 0.088582] usbcore: registered new device driver usb [ 0.088750] mc: Linux media interface: v0.10 [ 0.088761] videodev: Linux video capture interface: v2.00 [ 0.088895] pps_core: LinuxPPS API ver. 1 registered [ 0.088901] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.088910] PTP clock support registered [ 0.089104] tegra_wdt_t18x 2190000.watchdog: Tegra WDT init timeout = 120 sec [ 0.089125] tegra_wdt_t18x 2190000.watchdog: Registered successfully [ 0.090402] Registered efivars operations [ 0.090805] FPGA manager framework [ 0.090911] Advanced Linux Sound Architecture Driver Initialized. [ 0.091166] Bluetooth: Core ver 2.22 [ 0.091183] NET: Registered protocol family 31 [ 0.091189] Bluetooth: HCI device and connection manager initialized [ 0.091198] Bluetooth: HCI socket layer initialized [ 0.091203] Bluetooth: L2CAP socket layer initialized [ 0.091213] Bluetooth: SCO socket layer initialized [ 0.091784] camchar: rtcpu character device driver loaded [ 0.092001] clocksource: Switched to clocksource arch_sys_counter [ 0.250702] VFS: Disk quotas dquot_6.6.0 [ 0.250753] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.250870] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.251068] tegra-carveouts tegra-carveouts: fsi :dma coherent mem declare 0x00000000bf000000,16777216 [ 0.251079] tegra-carveouts tegra-carveouts: assigned reserved memory node fsi-carveout [ 0.251095] tegra-carveouts tegra-carveouts: vpr :dma coherent mem declare 0x00000000d6000000,704643072 [ 0.251103] pnp: PnP ACPI: disabled [ 0.251105] nvmap_page_pool_init: Total RAM pages: 7836361 [ 0.251109] nvmap_page_pool_init: nvmap page pool size: 979545 pages (3826 MB) [ 0.251166] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.251256] misc nvmap: created heap vpr base 0x00000000d6000000 size (688128KiB) [ 0.252755] la/ptsa driver initialized. [ 0.252803] NET: Registered protocol family 2 [ 0.253033] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.254895] misc nvmap: created heap fsi base 0x00000000bf000000 size (16384KiB) [ 0.255175] tcp_listen_portaddr_hash hash table entries: 16384 (order: 6, 262144 bytes, linear) [ 0.255235] TCP established hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.255428] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 0.255856] TCP: Hash tables configured (established 262144 bind 65536) [ 0.255933] UDP hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 0.256003] UDP-Lite hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 0.256143] NET: Registered protocol family 1 [ 0.256366] RPC: Registered named UNIX socket transport module. [ 0.256375] RPC: Registered udp transport module. [ 0.256380] RPC: Registered tcp transport module. [ 0.256384] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.256396] PCI: CLS 0 bytes, default 64 [ 0.256495] Trying to unpack rootfs image as initramfs... [ 0.365555] Freeing initrd memory: 8196K [ 0.367406] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.367559] kvm [1]: IPA Size Limit: 48 bits [ 0.367720] kvm [1]: VHE mode initialized successfully [ 0.368399] workingset: timestamp_bits=46 max_order=23 bucket_order=0 [ 0.369777] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.369988] NFS: Registering the id_resolver key type [ 0.370010] Key type id_resolver registered [ 0.370015] Key type id_legacy registered [ 0.370041] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.370051] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.370065] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.381548] NET: Registered protocol family 38 [ 0.381572] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 239) [ 0.381631] io scheduler mq-deadline registered [ 0.381637] io scheduler kyber registered [ 0.385029] tegra-pwm 3280000.pwm: PWM clk can sleep in ops [ 0.385056] tegra-pwm 32a0000.pwm: PWM clk can sleep in ops [ 0.385075] tegra-pwm 32c0000.pwm: PWM clk can sleep in ops [ 0.385091] tegra-pwm 32f0000.pwm: PWM clk can sleep in ops [ 0.387137] tegra_dc_assign_hw_data: no matching compatible node [ 0.387144] tegradccommon module_init failed [ 0.387150] tegradc module_init failed [ 0.387356] EINJ: ACPI disabled. [ 0.388538] tegra-pmc c360000.pmc: scratch reg offset dts data not present [ 0.388548] tegra-pmc: ### PMC reset source: SYS_RESET_N [ 0.388554] tegra-pmc: ### PMC reset level: L0 [ 0.388559] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.389558] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.393217] random: fast init done [ 0.393450] printk: console [ttyTCU0] enabled [ 2.221059] arm-smmu 12000000.iommu: probing hardware configuration... [ 2.226978] arm-smmu 12000000.iommu: SMMUv2 with: [ 2.231535] arm-smmu 12000000.iommu: stage 1 translation [ 2.236858] arm-smmu 12000000.iommu: stage 2 translation [ 2.242372] arm-smmu 12000000.iommu: nested translation [ 2.247537] arm-smmu 12000000.iommu: stream matching with 128 register groups [ 2.254711] arm-smmu 12000000.iommu: 128 context banks (0 stage-2 only) [ 2.262979] arm-smmu 12000000.iommu: Supported page sizes: 0x00001000 [ 2.267747] arm-smmu 12000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 2.274311] arm-smmu 12000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 2.281446] arm-smmu 10000000.iommu: probing hardware configuration... [ 2.287349] arm-smmu 10000000.iommu: SMMUv2 with: [ 2.292074] arm-smmu 10000000.iommu: stage 1 translation [ 2.297583] arm-smmu 10000000.iommu: stage 2 translation [ 2.303009] arm-smmu 10000000.iommu: nested translation [ 2.308436] arm-smmu 10000000.iommu: stream matching with 128 register groups [ 2.315608] arm-smmu 10000000.iommu: 128 context banks (0 stage-2 only) [ 2.323918] arm-smmu 10000000.iommu: Supported page sizes: 0x00001000 [ 2.328822] arm-smmu 10000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 2.335385] arm-smmu 10000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 2.342323] arm-smmu 8000000.iommu: probing hardware configuration... [ 2.348511] arm-smmu 8000000.iommu: SMMUv2 with: [ 2.353233] arm-smmu 8000000.iommu: stage 1 translation [ 2.358747] arm-smmu 8000000.iommu: stage 2 translation [ 2.364170] arm-smmu 8000000.iommu: nested translation [ 2.369335] arm-smmu 8000000.iommu: stream matching with 128 register groups [ 2.376511] arm-smmu 8000000.iommu: 128 context banks (0 stage-2 only) [ 2.384799] arm-smmu 8000000.iommu: Supported page sizes: 0x00001000 [ 2.389721] arm-smmu 8000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 2.396285] arm-smmu 8000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 2.403338] arm-smmu-suspend 12000000.smmu_suspend: arm_smmu_suspend probe successful [ 2.412396] tegra_profiler: version: 1.146, samples/io: 49/28 [ 2.416468] tegra_profiler: auth: init [ 2.421227] tegra23x-qspi 3270000.spi: Adding to iommu group 0 [ 2.426834] libphy: Fixed MDIO Bus: probed [ 2.430246] tun: Universal TUN/TAP device driver, 1.6 [ 2.435778] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 2.442578] hns3: Copyright (c) 2017 Huawei Corporation. [ 2.448102] e1000e: Intel(R) PRO/1000 Network Driver [ 2.452897] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.458861] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.464270] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.470112] PPP generic driver version 2.4.2 [ 2.474462] PPP BSD Compression module registered [ 2.479151] PPP Deflate Compression module registered [ 2.484412] PPP MPPE Compression module registered [ 2.489224] usbcore: registered new interface driver r8152 [ 2.494555] usbcore: registered new interface driver asix [ 2.499980] usbcore: registered new interface driver ax88179_178a [ 2.506102] usbcore: registered new interface driver cdc_ether [ 2.512052] usbcore: registered new interface driver net1080 [ 2.517654] usbcore: registered new interface driver cdc_subset [ 2.523690] usbcore: registered new interface driver zaurus [ 2.529381] usbcore: registered new interface driver cdc_ncm [ 2.535065] usbcore: registered new interface driver aqc111 [ 2.540580] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.546791] ohci-pci: OHCI PCI platform driver [ 2.551088] ohci-platform: OHCI generic platform driver [ 2.556405] tegra-xusb 3610000.xhci: Adding to iommu group 1 [ 2.562228] usbcore: registered new interface driver uas [ 2.567365] usbcore: registered new interface driver usb-storage [ 2.573326] tegra-xudc 3550000.xudc: Adding to iommu group 2 [ 2.579170] mousedev: PS/2 mouse device common for all mice [ 2.584514] usbcore: registered new interface driver xpad [ 2.591734] tegra_rtc c2a0000.rtc: registered as rtc1 [ 2.595277] tegra_rtc c2a0000.rtc: setting system clock to 1970-01-01T00:00:17 UTC (17) [ 2.603056] tegra_rtc c2a0000.rtc: Tegra internal Real Time Clock [ 2.609267] i2c /dev entries driver [ 2.612855] tegra-i2c 3160000.i2c: Adding to iommu group 3 [ 2.618432] tegra-i2c c240000.i2c: Adding to iommu group 3 [ 2.623827] tegra-i2c 3180000.i2c: Adding to iommu group 3 [ 2.629258] tegra-i2c 3190000.i2c: Adding to iommu group 3 [ 2.634582] tegra-i2c 31b0000.i2c: Adding to iommu group 3 [ 2.640095] tegra-i2c 31c0000.i2c: Adding to iommu group 3 [ 2.645522] tegra-i2c c250000.i2c: Adding to iommu group 3 [ 2.650860] tegra-i2c 31e0000.i2c: Adding to iommu group 3 [ 2.657932] tegra-camrtc-capture-vi tegra-capture-vi: ep of_device is not enabled endpoint. [ 2.664477] tegra-camrtc-capture-vi tegra-capture-vi: ep of_device is not enabled endpoint. [ 2.673521] device-mapper: uevent: version 1.0.3 [ 2.677406] device-mapper: ioctl: 4.43.0-ioctl (2020-10-01) initialised: dm-devel@redhat.com [ 2.686654] sdhci: Secure Digital Host Controller Interface driver [ 2.692128] sdhci: Copyright(c) Pierre Ossman [ 2.696584] Synopsys Designware Multimedia Card Interface Driver [ 2.702688] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.708557] sdhci-tegra 3460000.sdhci: Adding to iommu group 4 [ 2.708929] sdhci-tegra 3400000.sdhci: Adding to iommu group 5 [ 2.709376] pstore: ignoring unexpected backend 'efi' [ 2.709431] SMCCC: SOC_ID: ID = jep106:036b:0023 Revision = 0x00000401 [ 2.710158] tegra-bpmp bpmp: firmware: 43f75b5aad2b8e1992e4-f0425a554b3 debugfs initialized [ 4.306722] random: crng init done [ 4.330239] hid: raw HID events driver (C) Jiri Kosina [ 4.330809] usbcore: registered new interface driver usbhid [ 4.331003] usbhid: USB HID core driver [ 4.331324] tegra-dce d800000.dce: Adding to iommu group 6 [ 4.332767] dce: dce_ipc_channel_init:314 Invalid Channel State [0x0] for ch_type [2] [ 4.334127] tegra234-aon c000000.aon: Adding to iommu group 7 [ 4.334164] dce: dce_wait_boot_complete:100 dce is ready to receive bootstrap commands [ 4.335268] c000000.aon:hsp: probed [ 4.335548] tegra234-aon c000000.aon: init done [ 4.335952] tegra23x-psc e860000.psc: Adding to iommu group 8 [ 4.336431] tegra23x-psc e860000.psc: ext_cfg base:00000000ed949cff [ 4.336643] tegra23x-psc e860000.psc: init done [ 4.336992] tegra186-cam-rtcpu bc00000.rtcpu: Adding to iommu group 9 [ 4.337732] tegra186-cam-rtcpu bc00000.rtcpu: Trace buffer configured at IOVA=0xbff00000 [ 4.339338] dce: dce_mailbox_set_full_interrupt:165 Intr bit set multiple times for MB : [0x5] [ 4.339598] dce: dce_admin_ipc_handle_signal:119 Spurious signal on channel: [0]. Ignored... [ 4.340008] dce: dce_admin_send_cmd_ver:424 version : [0x2] err : [0x0] [ 4.342362] tegra-ivc-bus bc00000.rtcpu:ivc-bus: region 0: iova=0xbfec0000-0xbfee01ff size=131584 [ 4.353097] tegra-ivc-bus bc00000.rtcpu:ivc-bus:echo@0: echo: ver=0 grp=1 RX[16x64]=0x1000-0x1480 TX[16x64]=0x1480-00 [ 4.353210] dce: dce_mailbox_set_full_interrupt:165 Intr bit set multiple times for MB : [0x1] [ 4.372142] tegra-ivc-bus bc00000.rtcpu:ivc-bus:dbg@1: dbg: ver=0 grp=1 RX[1x448]=0x1900-0x1b40 TX[1x448]=0x1b40-0x10 [ 4.372623] dce: dce_admin_setup_clients_ipc:480 Channel Reset Complete for Type [1] ... [ 4.372625] dce: dce_admin_ipc_handle_signal:119 Spurious signal on channel: [1]. Ignored... [ 4.383617] tegra-ivc-bus bc00000.rtcpu:ivc-bus:dbg@2: dbg: ver=0 grp=1 RX[1x8192]=0x1d80-0x3e00 TX[1x8192]=0x3e00-00 [ 4.391957] dce: dce_admin_setup_clients_ipc:456 Get queue info failed for [2] [ 4.400856] tegra-ivc-bus bc00000.rtcpu:ivc-bus:ivccontrol@3: ivccontrol: ver=0 grp=1 RX[64x320]=0x5e80-0xaf00 TX[640 [ 4.411388] dce: dce_mailbox_set_full_interrupt:165 Intr bit set multiple times for MB : [0x2] [ 4.418677] tegra-ivc-bus bc00000.rtcpu:ivc-bus:ivccapture@4: ivccapture: ver=0 grp=1 RX[512x64]=0xff80-0x18000 TX[50 [ 4.430983] dce: dce_admin_setup_clients_ipc:480 Channel Reset Complete for Type [3] ... [ 4.430985] dce: dce_admin_ipc_handle_signal:119 Spurious signal on channel: [3]. Ignored... [ 4.430997] dce: dce_admin_ipc_handle_signal:119 Spurious signal on channel: [3]. Ignored... [ 4.439756] tegra-ivc-bus bc00000.rtcpu:ivc-bus:diag@5: diag: ver=0 grp=1 RX[1x64]=0x20080-0x20140 TX[1x64]=0x20140-0 [ 4.452699] dce: dce_worker:209 DCE_BOOT_DONE [ 4.460677] tegra186-cam-rtcpu bc00000.rtcpu: using cam RTCPU IRQ (115) [ 4.500633] tegra186-cam-rtcpu bc00000.rtcpu: tegra_camrtc_mon_create is successful [ 4.508769] tegra186-cam-rtcpu bc00000.rtcpu: firmware version cpu=rce cmd=6 sha1=ab261c6cb44ef92b00c3f83a96d5951f9c6 [ 4.521384] t19x_cache tegra-cache: probed [ 4.523896] scf-pmu-drv scf-pmu: Registered T23x SCF Uncore PMU [ 4.545747] nvpmodel: initialized successfully [ 4.546160] tegra_hv: get_hvd: not initialized yet [ 4.546335] user_ivc_mempool: hypervisor not present [ 4.546842] usbcore: registered new interface driver snd-usb-audio [ 4.550805] u32 classifier [ 4.553048] input device check on [ 4.556632] Actions configured [ 4.560066] Initializing XFRM netlink socket [ 4.564682] NET: Registered protocol family 10 [ 4.569886] Segment Routing with IPv6 [ 4.572435] NET: Registered protocol family 17 [ 4.576687] NET: Registered protocol family 15 [ 4.581174] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br. [ 4.594540] Bluetooth: RFCOMM socket layer initialized [ 4.599184] Bluetooth: RFCOMM ver 1.11 [ 4.603107] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.608963] Bluetooth: HIDP socket layer initialized [ 4.614610] 9pnet: Installing 9P2000 support [ 4.618374] Key type dns_resolver registered [ 4.623330] registered taskstats version 1 [ 4.627126] pstore: Using crash dump compression: deflate [ 4.632424] tegra194-pcie 14100000.pcie: Adding to iommu group 10 [ 4.643685] tegra194-pcie 14100000.pcie: Using GICv2m MSI allocator [ 4.645259] tegra194-pcie 14160000.pcie: Adding to iommu group 11 [ 4.656053] tegra194-pcie 14160000.pcie: Using GICv2m MSI allocator [ 4.657667] tegra194-pcie 141a0000.pcie: Adding to iommu group 12 [ 4.668344] tegra194-pcie 141a0000.pcie: Using GICv2m MSI allocator [ 4.689357] tegra-gpcdma 2600000.gpcdma: Adding to iommu group 3 [ 4.690531] tegra-gpcdma 2600000.gpcdma: GPC DMA driver register 31 channels [ 4.690903] host1x 13e40000.host1x: Adding to iommu group 13 [ 5.698557] t23x_init_gating_regs: Timed out waiting for syncpt ram init! [ 5.707217] host1x 13e40000.host1x: initialized [ 5.707599] iommu_context_dev 13e40000.host1x:niso0_ctx0: Adding to iommu group 14 [ 5.708092] iommu_context_dev 13e40000.host1x:niso0_ctx0: initialized (streamid=53, iommu=smmu.0x0000000012000000) [ 5.709661] iommu_context_dev 13e40000.host1x:niso0_ctx1: Adding to iommu group 15 [ 5.710100] iommu_context_dev 13e40000.host1x:niso0_ctx1: initialized (streamid=54, iommu=smmu.0x0000000012000000) [ 5.711660] iommu_context_dev 13e40000.host1x:niso0_ctx2: Adding to iommu group 16 [ 5.712115] iommu_context_dev 13e40000.host1x:niso0_ctx2: initialized (streamid=55, iommu=smmu.0x0000000012000000) [ 5.713653] iommu_context_dev 13e40000.host1x:niso0_ctx3: Adding to iommu group 17 [ 5.714059] iommu_context_dev 13e40000.host1x:niso0_ctx3: initialized (streamid=56, iommu=smmu.0x0000000012000000) [ 5.715587] iommu_context_dev 13e40000.host1x:niso0_ctx4: Adding to iommu group 18 [ 5.715999] iommu_context_dev 13e40000.host1x:niso0_ctx4: initialized (streamid=57, iommu=smmu.0x0000000012000000) [ 5.717540] iommu_context_dev 13e40000.host1x:niso0_ctx5: Adding to iommu group 19 [ 5.717928] iommu_context_dev 13e40000.host1x:niso0_ctx5: initialized (streamid=58, iommu=smmu.0x0000000012000000) [ 5.729278] iommu_context_dev 13e40000.host1x:niso0_ctx6: Adding to iommu group 20 [ 5.735819] iommu_context_dev 13e40000.host1x:niso0_ctx6: initialized (streamid=59, iommu=smmu.0x0000000012000000) [ 5.747290] iommu_context_dev 13e40000.host1x:niso0_ctx7: Adding to iommu group 21 [ 5.753877] iommu_context_dev 13e40000.host1x:niso0_ctx7: initialized (streamid=60, iommu=smmu.0x0000000012000000) [ 5.765311] iommu_context_dev 13e40000.host1x:niso1_ctx0: Adding to iommu group 22 [ 5.771895] iommu_context_dev 13e40000.host1x:niso1_ctx0: initialized (streamid=53, iommu=smmu.0x0000000008000000) [ 5.783352] iommu_context_dev 13e40000.host1x:niso1_ctx1: Adding to iommu group 23 [ 5.789922] iommu_context_dev 13e40000.host1x:niso1_ctx1: initialized (streamid=54, iommu=smmu.0x0000000008000000) [ 5.801360] iommu_context_dev 13e40000.host1x:niso1_ctx2: Adding to iommu group 24 [ 5.807919] iommu_context_dev 13e40000.host1x:niso1_ctx2: initialized (streamid=55, iommu=smmu.0x0000000008000000) [ 5.819388] iommu_context_dev 13e40000.host1x:niso1_ctx3: Adding to iommu group 25 [ 5.826012] iommu_context_dev 13e40000.host1x:niso1_ctx3: initialized (streamid=56, iommu=smmu.0x0000000008000000) [ 5.837422] iommu_context_dev 13e40000.host1x:niso1_ctx4: Adding to iommu group 26 [ 5.843963] iommu_context_dev 13e40000.host1x:niso1_ctx4: initialized (streamid=57, iommu=smmu.0x0000000008000000) [ 5.855427] iommu_context_dev 13e40000.host1x:niso1_ctx5: Adding to iommu group 27 [ 5.862004] iommu_context_dev 13e40000.host1x:niso1_ctx5: initialized (streamid=58, iommu=smmu.0x0000000008000000) [ 5.873463] iommu_context_dev 13e40000.host1x:niso1_ctx6: Adding to iommu group 28 [ 5.880012] iommu_context_dev 13e40000.host1x:niso1_ctx6: initialized (streamid=59, iommu=smmu.0x0000000008000000) [ 5.891480] iommu_context_dev 13e40000.host1x:niso1_ctx7: Adding to iommu group 29 [ 5.898050] iommu_context_dev 13e40000.host1x:niso1_ctx7: initialized (streamid=60, iommu=smmu.0x0000000008000000) [ 5.909539] falcon 15340000.vic: Adding to iommu group 30 [ 5.917929] falcon 15340000.vic: initialized [ 5.918267] falcon 15380000.nvjpg: Adding to iommu group 31 [ 5.926559] falcon 15380000.nvjpg: initialized [ 5.928479] falcon 15540000.nvjpg1: Adding to iommu group 32 [ 5.936666] falcon 15540000.nvjpg1: initialized [ 5.938888] falcon 154c0000.nvenc: Adding to iommu group 33 [ 5.948498] falcon 154c0000.nvenc: initialized [ 5.949134] falcon 15a50000.ofa: Adding to iommu group 34 [ 5.957213] falcon 15a50000.ofa: initialized [ 5.959024] nvdec 15480000.nvdec: Adding to iommu group 35 [ 5.970044] nvdec 15480000.nvdec: initialized [ 5.970260] tsec 15500000.tsec: Adding to iommu group 36 [ 5.978262] tsec 15500000.tsec: initialized [ 5.980298] gic 2a41000.agic-controller: GIC IRQ controller registered [ 5.990580] tegra-aconnect aconnect@2a41000: Tegra ACONNECT bus registered [ 5.997568] gpio-394 (camera-control-output-low): hogged as output/low [ 5.998296] gpio-397 (camera-control-output-low): hogged as output/low [ 6.004777] gpio-487 (camera-control-output-low): hogged as output/low [ 6.010985] gpio-486 (camera-control-output-low): hogged as output/low [ 6.018392] gpiochip0: registered GPIOs 348 to 511 on tegra234-gpio [ 6.024431] gpiochip1: registered GPIOs 316 to 347 on tegra234-gpio-aon [ 6.030532] tegra-pwm 3280000.pwm: PWM clk can sleep in ops [ 6.036699] tegra-pwm 32a0000.pwm: PWM clk can sleep in ops [ 6.042282] tegra-pwm 32c0000.pwm: PWM clk can sleep in ops [ 6.047855] tegra-pwm 32f0000.pwm: PWM clk can sleep in ops [ 6.055213] misc tegra_camera_ctrl: tegra_camera_isomgr_register tpg_max_iso = 3916800KBs [ 6.061578] tegra194-isp5 14800000.isp: Adding to iommu group 37 [ 6.070113] t194-nvcsi 13e40000.host1x:nvcsi@15a00000: context isolation disabled due to no IOMMU [ 6.076635] t194-nvcsi 13e40000.host1x:nvcsi@15a00000: initialized [ 6.082907] tegra194-vi5 13e40000.host1x:vi0@15c00000: Adding to iommu group 38 [ 6.090508] tegra194-vi5 13e40000.host1x:vi1@14c00000: Adding to iommu group 39 [ 6.097656] scare-pigeon 13e40000.host1x:vi0-thi@15f00000: context isolation disabled due to no IOMMU [ 6.106724] scare-pigeon 13e40000.host1x:vi0-thi@15f00000: initialized [ 6.112923] scare-pigeon 13e40000.host1x:vi0-thi@15f00000: grid-of-semaphores not supported [ 6.121023] scare-pigeon 13e40000.host1x:vi1-thi@14f00000: context isolation disabled due to no IOMMU [ 6.130306] scare-pigeon 13e40000.host1x:vi1-thi@14f00000: initialized [ 6.136807] scare-pigeon 13e40000.host1x:vi1-thi@14f00000: grid-of-semaphores not supported [ 6.145268] scare-pigeon 13e40000.host1x:isp-thi@14b00000: context isolation disabled due to no IOMMU [ 6.154918] scare-pigeon 13e40000.host1x:isp-thi@14b00000: initialized [ 6.161132] scare-pigeon 13e40000.host1x:isp-thi@14b00000: grid-of-semaphores not supported [ 6.169635] pva 16000000.pva0: Adding to iommu group 40 [ 6.193546] pva 16000000.pva0: initialized [ 6.200639] nvdla 15880000.nvdla0: Adding to iommu group 41 [ 6.209338] nvdla 15880000.nvdla0: initialized [ 6.210961] nvdla 158c0000.nvdla1: Adding to iommu group 42 [ 6.219079] nvdla 158c0000.nvdla1: initialized [ 6.220786] tegra-fuse-burn efuse-burn: shutdown limit check disabled [ 6.220960] tegra-fuse-burn efuse-burn: Fuse burn driver initialized [ 6.221281] serial-tegra 3100000.serial: Adding to iommu group 3 [ 6.221767] 3100000.serial: ttyTHS0 at MMIO 0x3100000 (irq = 13, base_baud = 0) is a TEGRA_UART [ 6.227764] serial-tegra 3130000.serial: Adding to iommu group 3 [ 6.233380] 3130000.serial: ttyTHS3 at MMIO 0x3130000 (irq = 64, base_baud = 0) is a TEGRA_UART [ 6.265313] tegra-xusb 3610000.xhci: Firmware timestamp: 2021-12-01 05:27:10 UTC, Version: 80.03 release [ 6.265574] tegra-xusb 3610000.xhci: xHCI Host Controller [ 6.265746] tegra-xusb 3610000.xhci: new USB bus registered, assigned bus number 1 [ 6.266738] tegra-xusb 3610000.xhci: hcc params 0x0180ff05 hci version 0x120 quirks 0x0000000000050810 [ 6.273770] tegra-xusb 3610000.xhci: irq 232, io mem 0x03610000 [ 6.279867] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 6.288004] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.295178] usb usb1: Product: xHCI Host Controller [ 6.300162] usb usb1: Manufacturer: Linux 5.10.65-tegra xhci-hcd [ 6.306201] usb usb1: SerialNumber: 3610000.xhci [ 6.311321] hub 1-0:1.0: USB hub found [ 6.314713] hub 1-0:1.0: 4 ports detected [ 6.318900] tegra-xusb 3610000.xhci: xHCI Host Controller [ 6.324146] tegra-xusb 3610000.xhci: new USB bus registered, assigned bus number 2 [ 6.331758] tegra-xusb 3610000.xhci: Host supports USB 3.1 Enhanced SuperSpeed [ 6.339191] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 6.347334] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.354592] usb usb2: Product: xHCI Host Controller [ 6.359574] usb usb2: Manufacturer: Linux 5.10.65-tegra xhci-hcd [ 6.365529] usb usb2: SerialNumber: 3610000.xhci [ 6.370585] hub 2-0:1.0: USB hub found [ 6.374119] hub 2-0:1.0: 4 ports detected [ 6.379692] bwmgr API not supported [ 6.379696] tegra-xusb 3610000.xhci: can't register EMC bwmgr (-22) [ 6.413325] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 2006000 KHz, changing to: 2035200 z [ 6.416785] cpufreq: cpufreq_online: CPU4: Running at unlisted initial frequency: 2009000 KHz, changing to: 2035200 z [ 6.420357] cpufreq: cpufreq_online: CPU8: Running at unlisted initial frequency: 2009000 KHz, changing to: 2035200 z [ 6.423504] tegra194-pcie 14100000.pcie: Using GICv2m MSI allocator [ 6.429545] sdhci-tegra 3400000.sdhci: Got CD GPIO [ 6.430242] tegra194-pcie 14100000.pcie: host bridge /pcie@14100000 ranges: [ 6.438773] tegra194-pcie 14100000.pcie: IO 0x0030100000..0x00301fffff -> 0x0030100000 [ 6.447082] tegra194-pcie 14100000.pcie: MEM 0x20a8000000..0x20afffffff -> 0x0040000000 [ 6.455582] tegra194-pcie 14100000.pcie: MEM 0x2080000000..0x20a7ffffff -> 0x2080000000 [ 6.459955] mmc0: CQHCI version 5.10 [ 6.473390] irq: IRQ290: trimming hierarchy from :pmc@c360000 [ 6.473592] sdhci-tegra 3400000.sdhci: wakeup init done, cdirq 290 [ 6.496533] mmc0: SDHCI controller on 3460000.sdhci [3460000.sdhci] using ADMA 64-bit [ 6.571999] tegra194-pcie 14100000.pcie: Link up [ 6.573109] tegra194-pcie 14100000.pcie: PCI host bridge to bus 0001:00 [ 6.573301] pci_bus 0001:00: root bus resource [bus 00-ff] [ 6.573444] pci_bus 0001:00: root bus resource [io 0x0000-0xfffff] (bus address [0x30100000-0x301fffff]) [ 6.573703] pci_bus 0001:00: root bus resource [mem 0x20a8000000-0x20afffffff] (bus address [0x40000000-0x47ffffff]) [ 6.573981] pci_bus 0001:00: root bus resource [mem 0x2080000000-0x20a7ffffff pref] [ 6.574227] pci 0001:00:00.0: [10de:229e] type 01 class 0x060400 [ 6.574491] pci 0001:00:00.0: PME# supported from D0 D3hot [ 6.577776] pci 0001:01:00.0: [10ec:c822] type 00 class 0x028000 [ 6.578039] pci 0001:01:00.0: reg 0x10: [io 0x0000-0x00ff] [ 6.578343] pci 0001:01:00.0: reg 0x18: [mem 0x20a8000000-0x20a800ffff 64bit] [ 6.579287] pci 0001:01:00.0: supports D1 D2 [ 6.579403] pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 6.582678] pci 0001:00:00.0: BAR 14: assigned [mem 0x20a8000000-0x20a80fffff] [ 6.582869] pci 0001:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 6.587080] pci 0001:01:00.0: BAR 2: assigned [mem 0x20a8000000-0x20a800ffff 64bit] [ 6.592151] usb 1-3: new full-speed USB device number 2 using tegra-xusb [ 6.594841] pci 0001:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 6.607761] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 6.613005] pci 0001:00:00.0: bridge window [io 0x1000-0x1fff] [ 6.619277] pci 0001:00:00.0: bridge window [mem 0x20a8000000-0x20a80fffff] [ 6.626459] pci 0001:00:00.0: Max Payload Size set to 128/ 256 (was 256), Max Read Rq 512 [ 6.634810] pci 0001:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 512 [ 6.643482] pcieport 0001:00:00.0: Adding to iommu group 10 [ 6.643505] mmc0: Command Queue Engine enabled [ 6.649111] pcieport 0001:00:00.0: PME: Signaling with IRQ 50 [ 6.653309] mmc0: periodic cache flush enabled [ 6.653315] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 6.653778] mmcblk0: mmc0:0001 G1M15M 59.3 GiB [ 6.659444] pcieport 0001:00:00.0: AER: enabled with IRQ 50 [ 6.663554] mmcblk0rpmb: mmc0:0001 G1M15M partition 3 4.00 MiB, chardev (510:0) [ 6.670591] tegra194-pcie 14160000.pcie: Using GICv2m MSI allocator [ 6.695051] tegra194-pcie 14160000.pcie: host bridge /pcie@14160000 ranges: [ 6.700399] tegra194-pcie 14160000.pcie: IO 0x0036100000..0x00361fffff -> 0x0036100000 [ 6.708882] tegra194-pcie 14160000.pcie: MEM 0x2428000000..0x242fffffff -> 0x0040000000 [ 6.717363] tegra194-pcie 14160000.pcie: MEM 0x2140000000..0x2427ffffff -> 0x2140000000 [ 6.731732] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 [ 6.764417] usb 1-3: New USB device found, idVendor=13d3, idProduct=3549, bcdDevice= 0.00 [ 6.764638] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 6.764826] usb 1-3: Product: Bluetooth Radio [ 6.764944] usb 1-3: Manufacturer: Realtek [ 6.765054] usb 1-3: SerialNumber: 00e04c000001 [ 6.889034] usb 2-3: new SuperSpeedPlus Gen 2 USB device number 2 using tegra-xusb [ 6.927610] usb 2-3: New USB device found, idVendor=0bda, idProduct=0420, bcdDevice= 1.40 [ 6.927866] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 6.928108] usb 2-3: Product: 4-Port USB 3.0 Hub [ 6.928246] usb 2-3: Manufacturer: Generic [ 6.941014] hub 2-3:1.0: USB hub found [ 6.943707] hub 2-3:1.0: 4 ports detected [ 7.044126] usb 1-4: new high-speed USB device number 3 using tegra-xusb [ 7.212750] usb 1-4: New USB device found, idVendor=0bda, idProduct=5420, bcdDevice= 1.40 [ 7.212991] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 7.213198] usb 1-4: Product: 4-Port USB 2.0 Hub [ 7.213332] usb 1-4: Manufacturer: Generic [ 7.214605] hub 1-4:1.0: USB hub found [ 7.215737] hub 1-4:1.0: 4 ports detected [ 7.824667] tegra194-pcie 14160000.pcie: Phy link never came up [ 7.824887] tegra194-pcie 14160000.pcie: PCI host bridge to bus 0004:00 [ 7.825068] pci_bus 0004:00: root bus resource [bus 00-ff] [ 7.825227] pci_bus 0004:00: root bus resource [io 0x100000-0x1fffff] (bus address [0x36100000-0x361fffff]) [ 7.825504] pci_bus 0004:00: root bus resource [mem 0x2428000000-0x242fffffff] (bus address [0x40000000-0x47ffffff]) [ 7.825796] pci_bus 0004:00: root bus resource [mem 0x2140000000-0x2427ffffff pref] [ 7.826043] pci 0004:00:00.0: [10de:229c] type 01 class 0x060400 [ 7.826307] pci 0004:00:00.0: PME# supported from D0 D3hot [ 7.832001] pci 0004:00:00.0: PCI bridge to [bus 01-ff] [ 7.832157] pci 0004:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 512 [ 7.832579] pcieport 0004:00:00.0: Adding to iommu group 11 [ 7.832869] pcieport 0004:00:00.0: PME: Signaling with IRQ 52 [ 7.833389] pcieport 0004:00:00.0: AER: enabled with IRQ 52 [ 7.833739] pci_bus 0004:01: busn_res: [bus 01-ff] is released [ 7.833973] pci 0004:00:00.0: Removing from iommu group 11 [ 7.834119] pci_bus 0004:00: busn_res: [bus 00-ff] is released [ 7.840563] tegra194-pcie 141a0000.pcie: Using GICv2m MSI allocator [ 7.845613] vdd-3v3-pcie: supplied by vdd-3v3-sys [ 7.850237] avdd-cam-2v8: supplied by vdd-3v3-sys [ 7.854874] vdd-dp: supplied by vdd-3v3-sys [ 7.859097] vdd-3v3-sd: supplied by vdd-3v3-sys [ 7.863960] dsi-vdd-1v8-bl-en: supplied by vdd-1v8-sys [ 7.870737] tegra194-isp5 14800000.isp: initialized [ 7.876566] tegra194-vi5 13e40000.host1x:vi0@15c00000: initialized [ 7.879969] (NULL device *): fops function table already registered [ 7.886950] tegra194-vi5 13e40000.host1x:vi1@14c00000: initialized [ 7.892768] tegra194-pcie 141a0000.pcie: Using GICv2m MSI allocator [ 7.892824] sdhci-tegra 3400000.sdhci: Got CD GPIO [ 7.916372] sdhci-tegra 3400000.sdhci: wakeup init done, cdirq 290 [ 8.004608] tegra194-pcie 141a0000.pcie: host bridge /pcie@141a0000 ranges: [ 8.004828] tegra194-pcie 141a0000.pcie: IO 0x003a100000..0x003a1fffff -> 0x003a100000 [ 8.005080] tegra194-pcie 141a0000.pcie: MEM 0x2b28000000..0x2b2fffffff -> 0x0040000000 [ 8.005316] tegra194-pcie 141a0000.pcie: MEM 0x2740000000..0x2b27ffffff -> 0x2740000000 [ 8.969324] mmc1: SDHCI controller on 3400000.sdhci [3400000.sdhci] using ADMA 64-bit [ 9.113196] tegra194-pcie 141a0000.pcie: Phy link never came up [ 9.113418] tegra194-pcie 141a0000.pcie: PCI host bridge to bus 0005:00 [ 9.113604] pci_bus 0005:00: root bus resource [bus 00-ff] [ 9.113761] pci_bus 0005:00: root bus resource [io 0x200000-0x2fffff] (bus address [0x3a100000-0x3a1fffff]) [ 9.114043] pci_bus 0005:00: root bus resource [mem 0x2b28000000-0x2b2fffffff] (bus address [0x40000000-0x47ffffff]) [ 9.114343] pci_bus 0005:00: root bus resource [mem 0x2740000000-0x2b27ffffff pref] [ 9.114600] pci 0005:00:00.0: [10de:229a] type 01 class 0x060400 [ 9.114863] pci 0005:00:00.0: PME# supported from D0 D3hot [ 9.120561] pci 0005:00:00.0: PCI bridge to [bus 01-ff] [ 9.120708] pci 0005:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 512 [ 9.121129] pcieport 0005:00:00.0: Adding to iommu group 12 [ 9.121432] pcieport 0005:00:00.0: PME: Signaling with IRQ 54 [ 9.121939] pcieport 0005:00:00.0: AER: enabled with IRQ 54 [ 9.122273] pci_bus 0005:01: busn_res: [bus 01-ff] is released [ 9.122501] pci 0005:00:00.0: Removing from iommu group 12 [ 9.122645] pci_bus 0005:00: busn_res: [bus 00-ff] is released [ 9.129299] nvethernet 6810000.ethernet: Adding to iommu group 43 [ 9.134329] nvethernet 6810000.ethernet: failed to read skip mac reset flag, default 0 [ 9.142019] nvethernet 6810000.ethernet: failed to read MDIO address [ 9.148578] nvethernet 6810000.ethernet: setting to default DMA bit mask [ 9.155412] nvethernet 6810000.ethernet: failed to read UPHY GBE mode- default to 10G [ 9.163158] nvethernet 6810000.ethernet: failed to get phy reset gpio error: -2 [ 9.174478] nvethernet 6810000.ethernet: Ethernet MAC address: 48:b0:2d:a5:33:c8 [ 9.177992] nvethernet 6810000.ethernet: Macsec not enabled [ 9.183316] nvethernet 6810000.ethernet: Macsec: Reduced MTU: 1466 Max: 16383 [ 9.195201] nvethernet 6810000.ethernet: eth0 (HW ver: 31) created with 10 DMA channels [ 9.198971] irq: IRQ292: trimming hierarchy from :pmc@c360000 [ 9.204265] irq: IRQ293: trimming hierarchy from :interrupt-controller@f400000-1 [ 9.211698] irq: IRQ294: trimming hierarchy from :pmc@c360000 [ 9.217310] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 9.224761] tegra-se-nvhost 15810000.se: Adding to iommu group 44 [ 9.230857] tegra-se-nvhost 15810000.se: initialized [ 9.241563] tegra-se-nvhost 15810000.se: tegra_se_probe: complete [ 9.241839] tegra-se-nvhost 15820000.se: Adding to iommu group 45 [ 9.248050] tegra-se-nvhost 15820000.se: initialized [ 9.254105] tegra-se-nvhost 15820000.se: tegra_se_probe: complete [ 9.258739] tegra-se-nvhost 15840000.se: Adding to iommu group 46 [ 9.265200] tegra-se-nvhost 15840000.se: initialized [ 9.270843] tegra-se-nvhost 15840000.se: tegra_se_probe: complete [ 9.276618] tegra_actmon d230000.actmon: in actmon_register()... [ 9.282135] tegra_actmon d230000.actmon: bwmgr_disable = 1 [ 9.288030] tegra_actmon d230000.actmon: initialization Completed for the device mc_all [ 9.295725] hvc_sysfs: hypervisor is not present [ 9.332047] ALSA device list: [ 9.332133] No soundcards found. [ 9.332822] Freeing unused kernel memory: 3968K [ 9.332993] Run /init as init process [ 9.343656] Root device found: mmcblk0p1 [ 9.344252] Found dev node: /dev/mmcblk0p1 [ 9.368355] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 9.369594] Rootfs mounted over mmcblk0p1 [ 9.381687] Switching from initrd to actual rootfs [ 9.517269] systemd[1]: System time before build time, advancing clock. [ 9.547041] systemd[1]: systemd 245.4-4ubuntu3.19 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMAC) [ 9.548136] systemd[1]: Detected architecture arm64. [ 9.590995] systemd[1]: Set hostname to . [ 9.772255] systemd[1]: system-modprobe.slice: unit configures an IP firewall, but the local system does not support. [ 9.772631] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 9.773657] systemd[1]: Created slice system-modprobe.slice. [ 9.774241] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 9.774751] systemd[1]: Created slice User and Session Slice. [ 9.775016] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 9.775453] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 9.775787] systemd[1]: Reached target User and Group Name Lookups. [ 9.776018] systemd[1]: Reached target Slices. [ 9.776187] systemd[1]: Reached target Mounting snaps. [ 9.776365] systemd[1]: Reached target Mounted snaps. [ 9.776550] systemd[1]: Reached target Swap. [ 9.776888] systemd[1]: Listening on RPCbind Server Activation Socket. [ 9.777197] systemd[1]: Listening on Syslog Socket. [ 9.777449] systemd[1]: Listening on fsck to fsckd communication Socket. [ 9.780277] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 9.787048] systemd[1]: Listening on Journal Audit Socket. [ 9.792368] systemd[1]: Listening on Journal Socket (/dev/log). [ 9.798420] systemd[1]: Listening on Journal Socket. [ 9.803412] systemd[1]: Listening on udev Control Socket. [ 9.808881] systemd[1]: Listening on udev Kernel Socket. [ 9.815289] systemd[1]: Mounting Huge Pages File System... [ 9.820701] systemd[1]: Mounting POSIX Message Queue File System... [ 9.826739] systemd[1]: Mounting RPC Pipe File System... [ 9.832106] systemd[1]: Mounting Kernel Debug File System... [ 9.837859] systemd[1]: Mounting Kernel Trace File System... [ 9.843816] systemd[1]: Starting Journal Service... [ 9.854454] systemd[1]: Starting Set the console keyboard layout... [ 9.854721] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being . [ 9.865840] systemd[1]: Starting Load Kernel Module chromeos_pstore... [ 9.871906] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped. [ 9.879971] systemd[1]: Condition check resulted in Load Kernel Module efi_pstore being skipped. [ 9.889637] systemd[1]: Starting Load Kernel Module pstore_blk... [ 9.895930] systemd[1]: Starting Load Kernel Module pstore_zone... [ 9.901202] systemd[1]: Condition check resulted in Load Kernel Module ramoops being skipped. [ 9.910608] systemd[1]: Started Nameserver information manager. [ 9.915792] systemd[1]: Reached target Network (Pre). [ 9.921704] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 9.930074] systemd[1]: Condition check resulted in File System Check on Root Device being skipped. [ 9.942607] systemd[1]: Starting Load Kernel Modules... [ 9.945373] systemd[1]: Starting Remount Root and Kernel File Systems... [ 9.952066] systemd[1]: Starting udev Coldplug all Devices... [ 9.955989] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 9.963431] systemd[1]: Started Journal Service. [ 9.980380] systemd-journald[305]: Received client request to flush runtime journal. Ubuntu 20.04.5 LTS ubuntu ttyTCU0