[0000.159] [L4T TegraBoot] (version 00.00.2018.01-l4t-80a468da) [0000.165] Processing in cold boot mode Bootloader 2 [0000.169] A02 Bootrom Patch rev = 1023 [0000.173] Power-up reason: software reset [0000.177] No Battery Present [0000.179] pmic max77620 reset reason [0000.183] pmic max77620 NVERC : 0x0 [0000.186] RamCode = 2 [0000.188] Platform has DDR4 type RAM [0000.192] max77620 disabling SD1 Remote Sense [0000.196] Setting DDR voltage to 1125mv [0000.200] Serial Number of Pmic Max77663: 0x1704a4 [0000.208] Entering ramdump check [0000.211] Get RamDumpCarveOut = 0x0 [0000.214] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.219] Last reboot was clean, booting normally! [0000.224] Sdram initialization is successful [0000.228] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.234] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.240] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.245] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.251] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.257] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.263] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.269] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.285] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.291] Platform-DebugCarveout: 0 [0000.294] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.300] Non secure mode, and RB not enabled. [0000.304] Read GPT from (4:0) [0000.470] Csd NumOfBlocks=124735488 [0000.475] Set High speed to 1 [0000.478] Error mask set in wait for cmd complete with error 0x3 in HwSdmmcWaitForCommandComplete func at 278 line [0000.489] Command complete wait failed with error 0x3 Interrupt 0x18001 [0000.495] Number of retries left 4 [0000.504] Using GPT Primary to query partitions [0000.509] Loading Tboot-CPU binary [0000.518] Verifying TBC in OdmNonSecureSBK mode [0000.528] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.535] Bootloader downloaded successfully. [0000.539] Downloaded Tboot-CPU binary to 0xa0000258 [0000.544] MAX77620_GPIO5 configured [0000.548] CPU power rail is up [0000.550] CPU clock enabled [0000.554] Performing RAM repair [0000.557] Updating A64 Warmreset Address to 0xa00002e9 [0000.562] Read GPT from (4:0) [0000.570] Using GPT Primary to query partitions [0000.575] Loading NvTbootBootloaderDTB [0000.599] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.664] Bootloader DTB Load Address: 0x83000000 [0000.669] Read GPT from (4:0) [0000.677] Using GPT Primary to query partitions [0000.681] Loading NvTbootKernelDTB [0000.705] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.770] Kernel DTB Load Address: 0x83100000 [0000.774] Read GPT from (4:0) [0000.782] Using GPT Primary to query partitions [0000.787] Loading cboot binary [0000.816] Verifying EBT in OdmNonSecureSBK mode [0000.858] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.865] Bootloader downloaded successfully. [0000.869] Read GPT from (4:0) [0000.877] Using GPT Primary to query partitions [0000.882] Read PT from (2:0) [0000.897] Using BFS PT to query partitions [0000.901] PT: Partition NCT NOT found ! [0000.905] Warning: Find Partition via PT Failed [0000.909] Next binary entry address: 0x92c00258 [0000.914] BoardId: 3448 [0000.918] Overriding pmu board id with proc board id [0000.923] Display board id is not available [0000.927] Read GPT from (4:0) [0000.935] Using GPT Primary to query partitions [0000.963] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.015] /bpmp deleted [0001.017] SC7EntryFw header found loaded at 0xff700000 [0001.206] OVR2 PMIC [0001.208] Bpmp FW successfully loaded [0001.211] Read GPT from (4:0) [0001.219] Using GPT Primary to query partitions [0001.224] WB0 init successfully at 0xff780000 [0001.228] Set NvDecSticky Bits [0001.232] GSC2 address ff53fffc value c0edbbcc [0001.238] GSC MC Settings done [0001.241] Read GPT from (4:0) [0001.249] Using GPT Primary to query partitions [0001.254] TOS Image length 53680 [0001.257] Monitor size 53680 [0001.260] OS size 0 [0001.266] Secure Os AES-CMAC Verification Success! [0001.271] TOS image cipher info: plaintext [0001.275] Loading and Validation of Secure OS Successful [0001.291] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.295] NvTbootPackSdramParams: start. [0001.301] NvTbootPackSdramParams: done. [0001.304] Tegraboot started after 87447 us [0001.308] Basic modules init took 875112 us [0001.312] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB [0001.318] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.323] Storage Device Read Time = 116 ms, Read Size = 2359 KB [0001.329] Storage Device Write Time = 0 ms, Write Size = 0 KB [0001.335] Next stage binary read took 24115 us [0001.339] Carveout took -48314 us [0001.342] CPU initialization took 397658 us [0001.346] Total time taken by TegraBoot 1248571 us [0001.351] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):23b153a63 NOTICE: BL31: Built : 22:39:57, Dec 9 2019 ERROR: Error initializing runtime service trusty_fast [0001.473] RamCode = 2 [0001.475] get_emc_table_offset: Can't find emc-table node [0001.480] LPDDR4 Training: Can't find emc-table node [0001.524] [0001.525] Debug Init done [0001.528] Marked DTB cacheable [0001.531] Bootloader DTB loaded at 0x83000000 [0001.536] Marked DTB cacheable [0001.539] Kernel DTB loaded at 0x83100000 [0001.542] DeviceTree Init done [0001.558] Pinmux applied successfully [0001.562] gicd_base: 0x50041000 [0001.566] gicc_base: 0x50042000 [0001.569] Interrupts Init done [0001.573] Using base:0x60005090 & irq:208 for tick-timer [0001.578] Using base:0x60005098 for delay-timer [0001.583] platform_init_timer: DONE [0001.586] Timer(tick) Init done [0001.590] osc freq = 38400 khz [0001.594] [0001.595] Welcome to L4T Cboot [0001.598] [0001.599] Cboot Version: 00.00.2018.01-t210-40c3ff9c [0001.604] calling constructors [0001.607] initializing heap [0001.610] initializing threads [0001.613] initializing timers [0001.616] creating bootstrap completion thread [0001.620] top of bootstrap2() [0001.623] CPU: ARM Cortex A57 [0001.626] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.630] initializing platform [0001.638] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.643] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.647] Macronix QSPI chip present [0001.651] SPI device register [0001.653] init boot device [0001.656] allocating memory for boot device(SPI) [0001.661] registering boot device [0001.670] sdmmc node status = okay [0001.673] sdcard instance = 0 [0001.676] sdcard gpio handle 0x56 [0001.679] sdcard gpio pin 0xc9 [0001.682] sdcard gpio flags 0x0 [0001.685] vmmc-supply 0x99 [0001.688] Instance: 0 [0001.690] Allocating memory for context [0001.694] enabling clock [0001.696] sd card init [0001.699] Check card present and stable [0001.702] Send command 0 [0001.727] Send command 3 [0001.731] Set RCA for the card [0001.734] Query card specific data by command 9 [0001.740] Parse CSD data [0001.743] Send command 7 [0001.753] Calling sd device register [0001.757] Init sdcard [0001.759] Allocating memory for boot device [0001.763] Registering user device [0001.776] Enable APE clock [0001.779] Un-powergate APE partition [0001.782] of_register: registering tegra_udc to of_hal [0001.787] of_register: registering inv20628-driver to of_hal [0001.793] of_register: registering ads1015-driver to of_hal [0001.798] of_register: registering lp8557-bl-driver to of_hal [0001.804] of_register: registering bq2419x_charger to of_hal [0001.810] of_register: registering bq27441_fuel_gauge to of_hal [0001.821] gpio framework initialized [0001.825] of_register: registering tca9539_gpio to of_hal [0001.830] of_register: registering tca9539_gpio to of_hal [0001.836] of_register: registering i2c_bus_driver to of_hal [0001.841] of_register: registering i2c_bus_driver to of_hal [0001.847] of_register: registering i2c_bus_driver to of_hal [0001.852] pmic framework initialized [0001.856] of_register: registering max77620_pmic to of_hal [0001.861] regulator framework initialized [0001.865] of_register: registering tps65132_bl_driver to of_hal [0001.871] initializing target [0001.877] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.885] board ID = D78, board SKU = 0 [0001.889] Skipping Z3! [0001.893] fixed regulator driver initialized [0001.911] initializing OF layer [0001.914] NCK carveout not present [0001.917] Skipping dts_overrides [0001.921] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.938] I2C Bus Init done [0001.941] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.951] I2C Bus Init done [0001.954] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.964] I2C Bus Init done [0001.967] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.977] I2C Bus Init done [0001.980] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.990] I2C Bus Init done [0001.993] of_children_init: Ops found for compatible string maxim,max77620 [0002.003] max77620_init using irq 118 [0002.008] register 'maxim,max77620' pmic [0002.012] gpio_driver_register: register 'max77620-gpio' driver [0002.018] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.029] I2C Bus Init done [0002.032] NCK carveout not present [0002.042] Find /i2c@7000c000's alias i2c0 [0002.046] get eeprom at 1-a0, size 256, type 0 [0002.055] Find /i2c@7000c500's alias i2c2 [0002.059] get eeprom at 3-a0, size 256, type 0 [0002.063] get eeprom at 3-ae, size 256, type 0 [0002.068] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.073] I2C slave not started [0002.076] I2C write failed [0002.079] Writing offset failed [0002.082] eeprom_init: EEPROM read failed [0002.086] pm_ids_update: eeprom init failed [0002.090] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.120] pm_ids_update: The pm board id is 3448-0000-401 [0002.126] Adding plugin-manager/ids/3448-0000-401=/i2c@7000c500:module@0x50 [0002.134] pm_ids_update: pm id update successful [0002.139] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.169] pm_ids_update: The pm board id is 3449-0000-400 [0002.175] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.183] pm_ids_update: pm id update successful [0002.214] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.220] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.228] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.234] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.242] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:a2:44 [0002.249] Plugin Manager: Parse ODM data 0x00094000 [0002.259] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0002.280] Find /i2c@7000c000's alias i2c0 [0002.284] get eeprom at 1-a0, size 256, type 0 [0002.293] Find /i2c@7000c500's alias i2c2 [0002.297] get eeprom at 3-a0, size 256, type 0 [0002.301] get eeprom at 3-ae, size 256, type 0 [0002.306] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.311] I2C slave not started [0002.314] I2C write failed [0002.317] Writing offset failed [0002.320] eeprom_init: EEPROM read failed [0002.324] pm_ids_update: eeprom init failed [0002.328] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.358] pm_ids_update: The pm board id is 3448-0000-401 [0002.364] Adding plugin-manager/ids/3448-0000-401=/i2c@7000c500:module@0x50 [0002.371] pm_ids_update: pm id update successful [0002.376] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.406] pm_ids_update: The pm board id is 3449-0000-400 [0002.413] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.420] pm_ids_update: pm id update successful [0002.450] Add serial number:1424320062595 as DT property [0002.458] Applying platform configs [0002.465] platform-init is not present. Skipping [0002.469] calling apps_init() [0002.494] Found 14 GPT partitions in "sd0" [0002.498] Proceeding to Cold Boot [0002.501] starting app android_boot_app [0002.505] Device state: unlocked [0002.508] display console init [0002.517] could not find regulator [0002.520] hdmi cable connected [0002.523] I2C slave not started [0002.526] I2C write failed [0002.529] Writing offset failed [0002.532] could not read edid [0002.536] tmds-config node not found [0002.541] pmc_set_io_pad_voltage: Error -2 retrieving plDT entry for leds-pwm not found a[0002.552] tform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.562] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.570] could not find regulator [0002.573] could not find regulator [0002.577] could not find regulator [0002.605] using default cmu settings [0002.609] dc_hdmi_enable, starting HDMI initialisation [0002.615] dc_hdmi_enable, HDMI initialisation complete [0002.620] list and configure display window [0002.625] display console init completed [0002.632] subnode volume_up is not found ! [0002.636] subnode back is not found ! [0002.640] subnode volume_down is not found ! [0002.644] subnode menu is not found ! [0002.648] Gpio keyboard init success [0002.691] found decompressor handler: lz4-legacy [0002.706] decompressing blob (type 1)... [0002.739] load_bmp_blob: panelresolution=480 type=0 [0002.790] decompressor handler not found [0002.794] load_firmware_blob: Firmware blob loaded, entries=2 [0002.800] -------> se_aes_verify_sbk_clear: 747 [0002.804] se_aes_verify_sbk_clear: Error [0002.808] bl_battery_charging: connected to external power supply [0002.815] xusb is supported [0002.822] error while finding nvidia,portmap [0003.326] xusb blob version 0 size 124416 [0003.330] firmware size 124416 [0003.334] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0003.346] xhci0: 64 bytes context size, 32-bit DMA [0003.386] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.406] uhub0: on usbus0 [0004.056] uhub0: 9 ports with 9 removable, self powered [0005.056] failed to get HID devices [0005.059] failed to init xhci or no usb device attached [0005.069] device_query_partition_size: failed to open partition sd0:MSC ! [0005.076] MSC Partition not found [0005.082] device_query_partition_size: failed to open partition sd0:USP ! [0005.089] USP partition read failed! [0005.093] blob_init: blob-partition USP header read failed [0005.098] android_boot Unable to update recovery partition [0005.104] kfs_getpartname: name = LNX [0005.107] Loading kernel from LNX [0005.205] load kernel from storage [0005.217] decompressor handler not found [0005.274] Successfully loaded kernel and ramdisk images [0005.280] load_bmp_blob: panelresolution=480 type=0 [0005.354] display bmp image done [0005.357] NCK carveout not present [0005.360] Skipping dts_overrides [0005.363] NCK carveout not present [0005.373] Find /i2c@7000c000's alias i2c0 [0005.377] get eeprom at 1-a0, size 256, type 0 [0005.386] Find /i2c@7000c500's alias i2c2 [0005.390] get eeprom at 3-a0, size 256, type 0 [0005.394] get eeprom at 3-ae, size 256, type 0 [0005.399] pm_ids_update: Updating 1,a0, size 256, type 0 [0005.404] I2C slave not started [0005.407] I2C write failed [0005.410] Writing offset failed [0005.413] eeprom_init: EEPROM read failed [0005.417] pm_ids_update: eeprom init failed [0005.421] pm_ids_update: Updating 3,a0, size 256, type 0 [0005.451] pm_ids_update: The pm board id is 3448-0000-401 [0005.458] Adding plugin-manager/ids/3448-0000-401=/i2c@7000c500:module@0x50 [0005.465] pm_ids_update: pm id update successful [0005.470] pm_ids_update: Updating 3,ae, size 256, type 0 [0005.500] pm_ids_update: The pm board id is 3449-0000-400 [0005.507] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0005.514] pm_ids_update: pm id update successful [0005.545] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.551] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0005.559] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.565] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0005.574] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:a2:44 [0005.580] Plugin Manager: Parse ODM data 0x00094000 [0005.590] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.605] Add serial number:1424320062595 as DT property [0005.614] "bpmp" doesn't exist, creating [0005.619] Updated bpmp info to DTB [0005.624] Updated initrd info to DTB [0005.628] "proc-board" doesn't exist, creating [0005.633] Updated board info to DTB [0005.637] "pmu-board" doesn't exist, creating [0005.642] Updated board info to DTB [0005.646] "display-board" doesn't exist, creating [0005.651] Updated board info to DTB [0005.655] "reset" doesn't exist, creating [0005.659] Updated reset info to DTB [0005.663] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb4000 is_hdmi_initialised=1 [0005.701] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.714] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.727] Updated bootarg info to DTB [0005.731] Adding uuid 000000016450f7401c00000007fd8540 to DT [0005.736] Adding eks info 0 to DT [0005.742] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0005.748] Updated memory info to DTB [0005.756] set vdd_core voltage to 1125 mv [0005.760] setting 'vdd-core' regulator to 1125000 micro volts [0005.786] Found secure-pmc; disable BPMP U-Boot 2016.07-g0536cf2a27 (Dec 09 2019 - 22:40:32 -0800) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 733 bytes read in 161 ms (3.9 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 5487751 bytes read in 287 ms (18.2 MiB/s) Retrieving file: /boot/Image 34191368 bytes read in 1532 ms (21.3 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb4000 is_hdmi_initialised=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 00000000831776f0 Starting kernel ...