þ[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-c536fca9) [0000.131] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.139] Power-up reason: pmc por [0000.142] No Battery Present [0000.145] pmic max77620 reset reason [0000.148] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.154] Platform has DDR4 type RAM [0000.157] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x815c8 [0000.173] Entering ramdump check [0000.176] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.189] Sdram initialization is successful [0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] Read GPT from (4:0) [0000.383] Csd NumOfBlocks=250347520 [0000.388] Set High speed to 1 [0000.392] Error mask set in wait for cmd complete with error 0x3 in HwSdmmcWaitForCommandComplete func at 278 line [0000.402] Command complete wait failed with error 0x3 Interrupt 0x18001 [0000.408] Number of retries left 4 [0000.417] Using GPT Primary to query partitions [0000.422] Loading Tboot-CPU binary [0000.431] Verifying TBC in OdmNonSecureSBK mode [0000.441] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.448] Bootloader downloaded successfully. [0000.452] Downloaded Tboot-CPU binary to 0xa0000258 [0000.457] MAX77620_GPIO5 configured [0000.461] CPU power rail is up [0000.463] CPU clock enabled [0000.467] Performing RAM repair [0000.470] Updating A64 Warmreset Address to 0xa00002e9 [0000.475] Loading NvTbootBootloaderDTB [0000.499] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.565] Bootloader DTB Load Address: 0x83000000 [0000.570] Loading NvTbootKernelDTB [0000.594] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.659] Kernel DTB Load Address: 0x83100000 [0000.664] Loading cboot binary [0000.694] Verifying EBT in OdmNonSecureSBK mode [0000.735] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.742] Bootloader downloaded successfully. [0000.747] Read PT from (2:0) [0000.762] Using BFS PT to query partitions [0000.766] PT: Partition NCT NOT found ! [0000.770] Warning: Find Partition via PT Failed [0000.774] Next binary entry address: 0x92c00258 [0000.779] BoardId: 3448 [0000.783] Overriding pmu board id with proc board id [0000.788] Display board id is not available [0000.816] Verifying SC7EntryFw in OdmNonSecureSBK mode [0000.868] /bpmp deleted [0000.870] SC7EntryFw header found loaded at 0xff700000 [0001.063] OVR2 PMIC [0001.065] Bpmp FW successfully loaded [0001.069] WB0 init successfully at 0xff780000 [0001.073] Set NvDecSticky Bits [0001.077] GSC2 address ff53fffc value c0edbbcc [0001.083] GSC MC Settings done [0001.086] TOS Image length 53680 [0001.089] Monitor size 53680 [0001.092] OS size 0 [0001.099] Secure Os AES-CMAC Verification Success! [0001.104] TOS image cipher info: plaintext [0001.107] Loading and Validation of Secure OS Successful [0001.123] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.128] NvTbootPackSdramParams: start. [0001.133] NvTbootPackSdramParams: done. [0001.137] Tegraboot started after 52351 us [0001.141] Basic modules init took 759525 us [0001.145] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB [0001.150] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.156] Storage Device Read Time = 106 ms, Read Size = 2241 KB [0001.162] Storage Device Write Time = 0 ms, Write Size = 0 KB [0001.167] Next stage binary read took 24208 us [0001.171] Carveout took -35890 us [0001.174] CPU initialization took 364278 us [0001.178] Total time taken by TegraBoot 1112121 us [0001.183] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):de895fd9e NOTICE: BL31: Built : 12:23:48, Oct 16 2020 ERROR: Error initializing runtime service trusty_fast [0001.305] RamCode = 0 [0001.310] LPDDR4 Training: Read DT: Number of tables = 2 [0001.315] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.328] EMC Training Successful [0001.331] 408000 not found in DVFS table [0001.337] RamCode = 0 [0001.341] DT Write: emc-table@204000 succeeded [0001.346] DT Write: emc-table@1600000 succeeded [0001.350] LPDDR4 Training: Write DT: Number of tables = 2 [0001.392] [0001.393] Debug Init done [0001.395] Marked DTB cacheable [0001.398] Bootloader DTB loaded at 0x83000000 [0001.403] Marked DTB cacheable [0001.406] Kernel DTB loaded at 0x83100000 [0001.410] DeviceTree Init done [0001.423] Pinmux applied successfully [0001.427] gicd_base: 0x50041000 [0001.431] gicc_base: 0x50042000 [0001.434] Interrupts Init done [0001.438] Using base:0x60005090 & irq:208 for tick-timer [0001.443] Using base:0x60005098 for delay-timer [0001.447] platform_init_timer: DONE [0001.451] Timer(tick) Init done [0001.454] osc freq = 38400 khz [0001.459] [0001.460] Welcome to L4T Cboot [0001.463] [0001.464] Cboot Version: 00.00.2018.01-t210-4686ce50 [0001.469] calling constructors [0001.472] initializing heap [0001.474] initializing threads [0001.477] initializing timers [0001.480] creating bootstrap completion thread [0001.485] top of bootstrap2() [0001.488] CPU: ARM Cortex A57 [0001.490] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.495] initializing platform [0001.503] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.507] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.512] Macronix QSPI chip present [0001.515] SPI device register [0001.518] init boot device [0001.520] allocating memory for boot device(SPI) [0001.525] registering boot device [0001.534] sdmmc node status = okay [0001.538] sdcard instance = 0 [0001.540] sdcard gpio handle 0x56 [0001.544] sdcard gpio pin 0xc9 [0001.547] sdcard gpio flags 0x0 [0001.550] vmmc-supply 0x99 [0001.552] Instance: 0 [0001.554] Allocating memory for context [0001.558] enabling clock [0001.561] sd card init [0001.563] Check card present and stable [0001.567] Send command 0 [0001.583] Send command 3 [0001.587] Set RCA for the card [0001.590] Query card specific data by command 9 [0001.597] Parse CSD data [0001.599] Send command 7 [0001.610] Calling sd device register [0001.613] Init sdcard [0001.615] Allocating memory for boot device [0001.619] Registering user device [0001.633] Enable APE clock [0001.635] Un-powergate APE partition [0001.639] of_register: registering tegra_udc to of_hal [0001.644] of_register: registering inv20628-driver to of_hal [0001.649] of_register: registering ads1015-driver to of_hal [0001.655] of_register: registering lp8557-bl-driver to of_hal [0001.661] of_register: registering bq2419x_charger to of_hal [0001.666] of_register: registering bq27441_fuel_gauge to of_hal [0001.678] gpio framework initialized [0001.681] of_register: registering tca9539_gpio to of_hal [0001.687] of_register: registering tca9539_gpio to of_hal [0001.692] of_register: registering i2c_bus_driver to of_hal [0001.697] of_register: registering i2c_bus_driver to of_hal [0001.703] of_register: registering i2c_bus_driver to of_hal [0001.709] pmic framework initialized [0001.712] of_register: registering max77620_pmic to of_hal [0001.718] regulator framework initialized [0001.721] of_register: registering tps65132_bl_driver to of_hal [0001.727] initializing target [0001.733] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.741] board ID = D78, board SKU = 0 [0001.745] Skipping Z3! [0001.750] fixed regulator driver initialized [0001.767] initializing OF layer [0001.770] NCK carveout not present [0001.773] Skipping dts_overrides [0001.777] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.794] I2C Bus Init done [0001.797] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.807] I2C Bus Init done [0001.810] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.820] I2C Bus Init done [0001.822] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.833] I2C Bus Init done [0001.835] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.846] I2C Bus Init done [0001.848] of_children_init: Ops found for compatible string maxim,max77620 [0001.859] max77620_init using irq 118 [0001.864] register 'maxim,max77620' pmic [0001.868] gpio_driver_register: register 'max77620-gpio' driver [0001.874] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.885] I2C Bus Init done [0001.888] NCK carveout not present [0001.898] Find /i2c@7000c000's alias i2c0 [0001.902] get eeprom at 1-a0, size 256, type 0 [0001.911] Find /i2c@7000c500's alias i2c2 [0001.914] get eeprom at 3-a0, size 256, type 0 [0001.919] get eeprom at 3-ae, size 256, type 0 [0001.923] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.929] I2C slave not started [0001.932] I2C write failed [0001.934] Writing offset failed [0001.937] eeprom_init: EEPROM read failed [0001.941] pm_ids_update: eeprom init failed [0001.945] pm_ids_update: Updating 3,a0, size 256, type 0 [0001.975] pm_ids_update: The pm board id is 3448-0000-400 [0001.982] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0001.990] pm_ids_update: pm id update successful [0001.994] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.000] I2C slave not started [0002.003] I2C write failed [0002.005] Writing offset failed [0002.008] eeprom_init: EEPROM read failed [0002.012] pm_ids_update: eeprom init failed [0002.042] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.048] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.056] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.062] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.071] updating /chosen/nvidia,ethernet-mac node 00:04:4b:eb:92:02 [0002.077] Plugin Manager: Parse ODM data 0x00094000 [0002.087] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.102] Find /i2c@7000c000's alias i2c0 [0002.106] get eeprom at 1-a0, size 256, type 0 [0002.115] Find /i2c@7000c500's alias i2c2 [0002.118] get eeprom at 3-a0, size 256, type 0 [0002.123] get eeprom at 3-ae, size 256, type 0 [0002.127] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.133] I2C slave not started [0002.136] I2C write failed [0002.138] Writing offset failed [0002.141] eeprom_init: EEPROM read failed [0002.145] pm_ids_update: eeprom init failed [0002.149] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.179] pm_ids_update: The pm board id is 3448-0000-400 [0002.186] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.193] pm_ids_update: pm id update successful [0002.197] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.203] I2C slave not started [0002.206] I2C write failed [0002.208] Writing offset failed [0002.211] eeprom_init: EEPROM read failed [0002.215] pm_ids_update: eeprom init failed [0002.246] Add serial number:1422919147195 as DT property [0002.253] Applying platform configs [0002.260] platform-init is not present. Skipping [0002.264] calling apps_init() [0002.290] Found 14 GPT partitions in "sd0" [0002.294] Proceeding to Cold Boot [0002.297] starting app android_boot_app [0002.301] Device state: unlocked [0002.304] display console init [0002.312] could not find regulator [0002.315] hdmi cable connected [0002.331] edid read success [0002.346] edid read success [0002.349] width DT entry for leds-pwm not found =[0002.357] 640, height = 480, frequency = 25174825 [0002.361] width = 640, height = 480, frequency = 25174825 [0002.367] width = 640, height = 480, frequency = 25174825 [0002.372] width = 800, height = 480, frequency = 33900000 [0002.377] width = 720, height = 576, frequency = 27000000 [0002.383] width = 720, height = 480, frequency = 26973026 [0002.388] width = 720, height = 480, frequency = 26973026 [0002.394] width = 720, height = 576, frequency = 26973026 [0002.399] width = 720, height = 576, frequency = 26973026 [0002.404] width = 1280, height = 720, frequency = 74175824 [0002.410] width = 1280, height = 720, frequency = 74175824 [0002.415] width = 1920, height = 1080, frequency = 148351648 [0002.421] width = 1920, height = 1080, frequency = 148351648 [0002.426] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.434] tmds-config node not found [0002.438] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.453] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.461] could not find regulator [0002.464] could not find regulator [0002.467] could not find regulator [0002.496] using default cmu settings [0002.499] dc_hdmi_enable, starting HDMI initialisation [0002.505] dc_hdmi_enable, HDMI initialisation complete [0002.510] list and configure display window [0002.519] display console init completed [0002.530] subnode volume_up is not found ! [0002.534] subnode back is not found ! [0002.538] subnode volume_down is not found ! [0002.542] subnode menu is not found ! [0002.546] Gpio keyboard init success [0002.590] found decompressor handler: lz4-legacy [0002.604] decompressing blob (type 1)... [0002.639] load_bmp_blob: panelresolution=1080 type=3 [0002.691] decompressor handler not found [0002.694] load_firmware_blob: Firmware blob loaded, entries=2 [0002.700] -------> se_aes_verify_sbk_clear: 747 [0002.705] se_aes_verify_sbk_clear: Error [0002.708] bl_battery_charging: connected to external power supply [0002.716] xusb is supported [0002.722] error while finding nvidia,portmap [0003.226] xusb blob version 0 size 124416 [0003.230] firmware size 124416 [0003.235] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0003.250] xhci0: 64 bytes context size, 32-bit DMA [0003.290] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.310] uhub0: on usbus0 [0003.960] uhub0: 9 ports with 9 removable, self powered [0005.000] uhub1: on usbus0 [0005.020] uhub1: MTT enabled [0006.220] uhub1: 7 ports with 7 removable, self powered [0010.270] failed to get HID devices [0010.274] failed to init xhci or no usb device attached [0010.284] device_query_partition_size: failed to open partition sd0:MSC ! [0010.291] MSC Partition not found [0010.297] device_query_partition_size: failed to open partition sd0:USP ! [0010.304] USP partition read failed! [0010.307] blob_init: blob-partition USP header read failed [0010.313] android_boot Unable to update recovery partition [0010.318] kfs_getpartname: name = LNX [0010.322] Loading kernel from LNX [0010.421] load kernel from storage [0010.432] decompressor handler not found [0010.490] Successfully loaded kernel and ramdisk images [0010.496] load_bmp_blob: panelresolution=1080 type=3 [0010.994] display bmp image done [0010.997] NCK carveout not present [0011.000] Skipping dts_overrides [0011.003] NCK carveout not present [0011.013] Find /i2c@7000c000's alias i2c0 [0011.017] get eeprom at 1-a0, size 256, type 0 [0011.026] Find /i2c@7000c500's alias i2c2 [0011.030] get eeprom at 3-a0, size 256, type 0 [0011.034] get eeprom at 3-ae, size 256, type 0 [0011.039] pm_ids_update: Updating 1,a0, size 256, type 0 [0011.044] I2C slave not started [0011.047] I2C write failed [0011.050] Writing offset failed [0011.053] eeprom_init: EEPROM read failed [0011.057] pm_ids_update: eeprom init failed [0011.061] pm_ids_update: Updating 3,a0, size 256, type 0 [0011.091] pm_ids_update: The pm board id is 3448-0000-400 [0011.098] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0011.105] pm_ids_update: pm id update successful [0011.110] pm_ids_update: Updating 3,ae, size 256, type 0 [0011.115] I2C slave not started [0011.118] I2C write failed [0011.121] Writing offset failed [0011.124] eeprom_init: EEPROM read failed [0011.128] pm_ids_update: eeprom init failed [0011.158] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0011.164] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0011.172] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0011.178] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0011.186] updating /chosen/nvidia,ethernet-mac node 00:04:4b:eb:92:02 [0011.193] Plugin Manager: Parse ODM data 0x00094000 [0011.203] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0011.211] Add serial number:1422919147195 as DT property [0011.220] "bpmp" doesn't exist, creating [0011.225] Updated bpmp info to DTB [0011.230] Updated initrd info to DTB [0011.234] "proc-board" doesn't exist, creating [0011.239] Updated board info to DTB [0011.242] "pmu-board" doesn't exist, creating [0011.248] Updated board info to DTB [0011.251] "display-board" doesn't exist, creating [0011.257] Updated board info to DTB [0011.260] "reset" doesn't exist, creating [0011.265] Updated reset info to DTB [0011.268] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb4000 is_hdmi_initialised=1 [0011.307] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0011.313] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0011.326] Updated bootarg info to DTB [0011.329] Adding uuid 00000001644577821000000004060180 to DT [0011.335] Adding eks info 0 to DT [0011.341] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0011.347] Updated memory info to DTB [0011.355] set vdd_core voltage to 1125 mv [0011.359] setting 'vdd-core' regulator to 1125000 micro volts [0011.380] Found secure-pmc; disable BPMP U-Boot 2016.07-g7a7e3f476e (Oct 16 2020 - 12:23:42 -0700) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 1  0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 844 bytes read in 74 ms (10.7 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 5487776 bytes read in 311 ms (16.8 MiB/s) Retrieving file: /boot/Image 34334728 bytes read in 1535 ms (21.3 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb4000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 0000000083177d54 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-hawkware (root@X112) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #3 SMP PREEMPT Mon Jan 4 11:56:48 EST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92cb4000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.087938] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.275857] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.275894] imx219 7-0010: board setup failed [ 1.300042] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.300081] imx219 8-0010: board setup failed