MLNX1 [my-vip: master] (config) # sh run ## ## Running database "initial" ## Generated at 2021/02/27 14:33:57 +0000 ## Hostname: MLNX1 ## ## ## Running-config temporary prefix mode setting ## no cli default prefix-modes enable ## ## License keys ## license install LK2-EFM_SX-5M11-5K11-5T11-88A1-BBD0-JP82-X ## ## Port configuration ## port 1/1-1/12 type ethernet force ## ## MLAG protocol ## protocol mlag ## ## Interface Ethernet configuration ## interface mlag-port-channel 10 interface mlag-port-channel 90 interface mlag-port-channel 100 interface port-channel 1 interface ethernet 1/1 mlag-channel-group 10 mode on interface ethernet 1/9 mlag-channel-group 90 mode active interface ethernet 1/10 mlag-channel-group 100 mode active interface ethernet 1/11-1/12 channel-group 1 mode active interface mlag-port-channel 90 switchport mode trunk interface mlag-port-channel 100 switchport mode trunk interface mlag-port-channel 10 no shutdown interface mlag-port-channel 90 no shutdown interface mlag-port-channel 100 no shutdown ## ## LAG configuration ## lacp port-channel load-balance ethernet source-destination-ip source-destination-port ## ## VLAN configuration ## vlan 20 vlan 40 vlan 50 vlan 60 vlan 80 vlan 1000 vlan 4000 interface mlag-port-channel 90 switchport trunk allowed-vlan none interface mlag-port-channel 100 switchport trunk allowed-vlan none interface mlag-port-channel 90 switchport trunk allowed-vlan add 1 interface mlag-port-channel 90 switchport trunk allowed-vlan add 20 interface mlag-port-channel 90 switchport trunk allowed-vlan add 40 interface mlag-port-channel 90 switchport trunk allowed-vlan add 50 interface mlag-port-channel 90 switchport trunk allowed-vlan add 60 interface mlag-port-channel 90 switchport trunk allowed-vlan add 80 interface mlag-port-channel 90 switchport trunk allowed-vlan add 1000 interface mlag-port-channel 100 switchport trunk allowed-vlan add 1 interface mlag-port-channel 100 switchport trunk allowed-vlan add 20 interface mlag-port-channel 100 switchport trunk allowed-vlan add 40 interface mlag-port-channel 100 switchport trunk allowed-vlan add 50 interface mlag-port-channel 100 switchport trunk allowed-vlan add 60 interface mlag-port-channel 100 switchport trunk allowed-vlan add 80 interface mlag-port-channel 100 switchport trunk allowed-vlan add 1000 ## ## STP configuration ## spanning-tree port type edge default ## ## L3 configuration ## ip l3 ip routing vrf default interface vlan 4000 interface vlan 4000 ip address 1.1.1.1/30 primary interface vlan 4000 mtu 9216 ## ## DCBX PFC configuration ## dcb priority-flow-control enable force interface port-channel 1 dcb priority-flow-control mode on force ## ## MLAG configurations ## mlag-vip my-vip ip 10.0.24.12 /22 force no mlag shutdown mlag system-mac 00:00:5E:00:01:5D interface port-channel 1 ipl 1 interface vlan 4000 ipl 1 peer-address 1.1.1.2 ## ## Network interface configuration ## interface ib0 ip address 0.0.0.0 /0 interface ib0 shutdown no interface mgmt0 dhcp interface mgmt0 ip address 10.0.24.10 /22 ## ## Network interface IPv6 configuration ## no interface mgmt0 ipv6 address autoconfig default no interface mgmt0 ipv6 dhcp client enable no interface mgmt0 ipv6 enable ## ## Other IP configuration ## hostname MLNX1 ## ## Other IPv6 configuration ## no ipv6 enable ## ## AAA remote server configuration ## # ldap bind-password ******** # radius-server key ******** # tacacs-server key ******** ## ## Network management configuration ## # web proxy auth basic password ******** ## ## X.509 certificates configuration ## # # Certificate name system-self-signed, ID 2d39143e298cf549f36260338a42388676534fe8 # (public-cert config omitted since private-key config is hidden) ## ## Persistent prefix mode setting ## cli default prefix-modes enable MLNX1 [my-vip: master] (config) # interface vlan 4000 MLNX1 [my-vip: master] (config interface vlan 4000) # ipl 1 peer-address 1.1.1.2 MLNX1 [my-vip: master] (config interface vlan 4000) # ex MLNX1 [my-vip: master] (config) # sh run ## ## Running database "initial" ## Generated at 2021/02/27 14:35:03 +0000 ## Hostname: MLNX1 ## ## ## Running-config temporary prefix mode setting ## no cli default prefix-modes enable ## ## License keys ## license install LK2-EFM_SX-5M11-5K11-5T11-88A1-BBD0-JP82-X ## ## Port configuration ## port 1/1-1/12 type ethernet force ## ## MLAG protocol ## protocol mlag ## ## Interface Ethernet configuration ## interface mlag-port-channel 10 interface mlag-port-channel 90 interface mlag-port-channel 100 interface port-channel 1 interface ethernet 1/1 mlag-channel-group 10 mode on interface ethernet 1/9 mlag-channel-group 90 mode active interface ethernet 1/10 mlag-channel-group 100 mode active interface ethernet 1/11-1/12 channel-group 1 mode active interface mlag-port-channel 90 switchport mode trunk interface mlag-port-channel 100 switchport mode trunk interface mlag-port-channel 10 no shutdown interface mlag-port-channel 90 no shutdown interface mlag-port-channel 100 no shutdown ## ## LAG configuration ## lacp port-channel load-balance ethernet source-destination-ip source-destination-port ## ## VLAN configuration ## vlan 20 vlan 40 vlan 50 vlan 60 vlan 80 vlan 1000 vlan 4000 interface mlag-port-channel 90 switchport trunk allowed-vlan none interface mlag-port-channel 100 switchport trunk allowed-vlan none interface mlag-port-channel 90 switchport trunk allowed-vlan add 1 interface mlag-port-channel 90 switchport trunk allowed-vlan add 20 interface mlag-port-channel 90 switchport trunk allowed-vlan add 40 interface mlag-port-channel 90 switchport trunk allowed-vlan add 50 interface mlag-port-channel 90 switchport trunk allowed-vlan add 60 interface mlag-port-channel 90 switchport trunk allowed-vlan add 80 interface mlag-port-channel 90 switchport trunk allowed-vlan add 1000 interface mlag-port-channel 100 switchport trunk allowed-vlan add 1 interface mlag-port-channel 100 switchport trunk allowed-vlan add 20 interface mlag-port-channel 100 switchport trunk allowed-vlan add 40 interface mlag-port-channel 100 switchport trunk allowed-vlan add 50 interface mlag-port-channel 100 switchport trunk allowed-vlan add 60 interface mlag-port-channel 100 switchport trunk allowed-vlan add 80 interface mlag-port-channel 100 switchport trunk allowed-vlan add 1000 ## ## STP configuration ## spanning-tree port type edge default ## ## L3 configuration ## ip l3 ip routing vrf default interface vlan 4000 interface vlan 4000 ip address 1.1.1.1/30 primary interface vlan 4000 mtu 9216 ## ## DCBX PFC configuration ## dcb priority-flow-control enable force interface port-channel 1 dcb priority-flow-control mode on force ## ## MLAG configurations ## mlag-vip my-vip ip 10.0.24.12 /22 force no mlag shutdown mlag system-mac 00:00:5E:00:01:5D interface port-channel 1 ipl 1 interface vlan 4000 ipl 1 peer-address 1.1.1.2 ## ## Network interface configuration ## interface ib0 ip address 0.0.0.0 /0 interface ib0 shutdown no interface mgmt0 dhcp interface mgmt0 ip address 10.0.24.10 /22 ## ## Network interface IPv6 configuration ## no interface mgmt0 ipv6 address autoconfig default no interface mgmt0 ipv6 dhcp client enable no interface mgmt0 ipv6 enable ## ## Other IP configuration ## hostname MLNX1 ## ## Other IPv6 configuration ## no ipv6 enable ## ## AAA remote server configuration ## # ldap bind-password ******** # radius-server key ******** # tacacs-server key ******** ## ## Network management configuration ## # web proxy auth basic password ******** ## ## X.509 certificates configuration ## # # Certificate name system-self-signed, ID 2d39143e298cf549f36260338a42388676534fe8 # (public-cert config omitted since private-key config is hidden) ## ## Persistent prefix mode setting ## cli default prefix-modes enable MLNX1 [my-vip: master] (config) # dcb priority-flow-control enable force MLNX1 [my-vip: master] (config) # sh ver Product name: MLNX-OS Product release: 3.6.8012 Build ID: #1-dev Build date: 2019-02-22 07:53:42 Target arch: ppc Target hw: m460ex Built by: jenkins@4dec51c9aed1 Version summary: PPC_M460EX 3.6.8012 2019-02-22 07:53:42 ppc Product model: ppc Product hw: m460ex Host ID: 123212341234 Uptime: 2h 21m 46.290s CPU load averages: 3.40 / 2.65 / 2.53 Number of CPUs: 1 System memory: 917 MB used / 1110 MB free / 2027 MB total Swap: 0 MB used / 0 MB free / 0 MB total MLNX1 [my-vip: master] (config) # MLNX1 [my-vip: master] (config) # MLNX1 [my-vip: master] (config) # MLNX1 [my-vip: master] (config) # MLNX1 [my-vip: master] (config) # MLNX1 [my-vip: master] (config) # MLNX1 [my-vip: master] (config) # MLNX1 [my-vip: master] (config) # sh run ## ## Running database "initial" ## Generated at 2021/02/27 14:47:58 +0000 ## Hostname: MLNX1 ## ## ## Running-config temporary prefix mode setting ## no cli default prefix-modes enable ## ## License keys ## license install LK2-EFM_SX-5M11-5K11-5T11-88A1-BBD0-JP82-X ## ## Port configuration ## port 1/1-1/12 type ethernet force ## ## MLAG protocol ## protocol mlag ## ## Interface Ethernet configuration ## interface mlag-port-channel 10 interface mlag-port-channel 90 interface mlag-port-channel 100 interface port-channel 1 interface ethernet 1/1 mlag-channel-group 10 mode on interface ethernet 1/9 mlag-channel-group 90 mode active interface ethernet 1/10 mlag-channel-group 100 mode active interface ethernet 1/11-1/12 channel-group 1 mode active interface mlag-port-channel 90 switchport mode trunk interface mlag-port-channel 100 switchport mode trunk interface mlag-port-channel 10 no shutdown interface mlag-port-channel 90 no shutdown interface mlag-port-channel 100 no shutdown ## ## LAG configuration ## lacp port-channel load-balance ethernet source-destination-ip source-destination-port ## ## VLAN configuration ## vlan 20 vlan 40 vlan 50 vlan 60 vlan 80 vlan 1000 vlan 4000 interface mlag-port-channel 90 switchport trunk allowed-vlan none interface mlag-port-channel 100 switchport trunk allowed-vlan none interface mlag-port-channel 90 switchport trunk allowed-vlan add 1 interface mlag-port-channel 90 switchport trunk allowed-vlan add 20 interface mlag-port-channel 90 switchport trunk allowed-vlan add 40 interface mlag-port-channel 90 switchport trunk allowed-vlan add 50 interface mlag-port-channel 90 switchport trunk allowed-vlan add 60 interface mlag-port-channel 90 switchport trunk allowed-vlan add 80 interface mlag-port-channel 90 switchport trunk allowed-vlan add 1000 interface mlag-port-channel 100 switchport trunk allowed-vlan add 1 interface mlag-port-channel 100 switchport trunk allowed-vlan add 20 interface mlag-port-channel 100 switchport trunk allowed-vlan add 40 interface mlag-port-channel 100 switchport trunk allowed-vlan add 50 interface mlag-port-channel 100 switchport trunk allowed-vlan add 60 interface mlag-port-channel 100 switchport trunk allowed-vlan add 80 interface mlag-port-channel 100 switchport trunk allowed-vlan add 1000 ## ## STP configuration ## spanning-tree port type edge default ## ## L3 configuration ## ip l3 ip routing vrf default interface vlan 4000 interface vlan 4000 ip address 1.1.1.1/30 primary interface vlan 4000 mtu 9216 ## ## DCBX PFC configuration ## dcb priority-flow-control enable force interface port-channel 1 dcb priority-flow-control mode on force ## ## MLAG configurations ## mlag-vip my-vip ip 10.0.24.12 /22 force no mlag shutdown mlag system-mac 00:00:5E:00:01:5D interface port-channel 1 ipl 1 interface vlan 4000 ipl 1 peer-address 1.1.1.2 ## ## Network interface configuration ## interface ib0 ip address 0.0.0.0 /0 interface ib0 shutdown no interface mgmt0 dhcp interface mgmt0 ip address 10.0.24.10 /22 ## ## Network interface IPv6 configuration ## no interface mgmt0 ipv6 address autoconfig default no interface mgmt0 ipv6 dhcp client enable no interface mgmt0 ipv6 enable ## ## Other IP configuration ## hostname MLNX1 ## ## Other IPv6 configuration ## no ipv6 enable ## ## AAA remote server configuration ## # ldap bind-password ******** # radius-server key ******** # tacacs-server key ******** ## ## Network management configuration ## # web proxy auth basic password ******** ## ## X.509 certificates configuration ## # # Certificate name system-self-signed, ID 2d39143e298cf549f36260338a42388676534fe8 # (public-cert config omitted since private-key config is hidden) ## ## Persistent prefix mode setting ## cli default prefix-modes enable MLNX1 [my-vip: master] (config) # sh ver Product name: MLNX-OS Product release: 3.6.8012 Build ID: #1-dev Build date: 2019-02-22 07:53:42 Target arch: ppc Target hw: m460ex Built by: jenkins@4dec51c9aed1 Version summary: PPC_M460EX 3.6.8012 2019-02-22 07:53:42 ppc Product model: ppc Product hw: m460ex Host ID: 123212341234 Uptime: 2h 22m 24.330s CPU load averages: 3.24 / 2.70 / 2.55 Number of CPUs: 1 System memory: 917 MB used / 1110 MB free / 2027 MB total Swap: 0 MB used / 0 MB free / 0 MB total MLNX1 [my-vip: master] (config) # sh mlag Admin status: Enabled Operational status: Up Reload-delay: 30 sec Keepalive-interval: 1 sec Upgrade-timeout: 60 min System-mac: 00:00:5E:00:01:5D MLAG Ports Configuration Summary: Configured: 3 Disabled: 0 Enabled: 3 MLAG Ports Status Summary: Inactive: 1 Active-partial: 0 Active-full: 2 MLAG IPLs Summary: ---------------------------------------------------------------------------------------------------------------- ID Group Vlan Operational Local Peer Up Time Toggle Counter Port-Channel Interface State IP address IP address ---------------------------------------------------------------------------------------------------------------- 1 Po1 4000 Up 1.1.1.1 1.1.1.2 0 days, 00:08:44 4 MLAG Members Summary: --------------------------------------------------------------------- System-id State Hostname --------------------------------------------------------------------- E4:1D:2D:3E:E7:88 Up E4:1D:2D:3A:49:08 Up - MLNX1 [my-vip: master] (config) # sg ml % Unrecognized command "sg". Type "?" for help. MLNX1 [my-vip: master] (config) # sh mlag-vip MLAG-VIP: MLAG group name: my-vip MLAG VIP address: 10.0.24.12/22 Active nodes: 1 -------------------------------------------------------------- Hostname VIP-State IP Address -------------------------------------------------------------- MLNX2 master 10.0.24.10 MLNX1 [my-vip: master] (config) # sh licenses License 1: LK2-EFM_SX-5M11-5K11-5T11-88A1-BBD0-JP82-X Feature: EFM_SX Description: Generic SX license Valid: yes Active: yes Eth enabled: true Eth L2 enabled: true Eth L3 enabled: true MLNX1 [my-vip: master] (config) # ping 1.1.1.1 PING 1.1.1.1 (1.1.1.1) 56(84) bytes of data. 64 bytes from 1.1.1.1: icmp_seq=1 ttl=64 time=0.126 ms 64 bytes from 1.1.1.1: icmp_seq=2 ttl=64 time=0.155 ms ^C --- 1.1.1.1 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1000ms rtt min/avg/max/mdev = 0.126/0.140/0.155/0.018 ms MLNX1 [my-vip: master] (config) # ping 1.1.1.2 PING 1.1.1.2 (1.1.1.2) 56(84) bytes of data. 64 bytes from 1.1.1.2: icmp_seq=1 ttl=64 time=0.603 ms 64 bytes from 1.1.1.2: icmp_seq=2 ttl=64 time=0.467 ms ^C --- 1.1.1.2 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 0.467/0.535/0.603/0.068 ms MLNX1 [my-vip: master] (config) # sh ip arp VRF Name: default Total number of entries: 3 -------------------------------------------------------------------------------------- Address Type Hardware Address Interface -------------------------------------------------------------------------------------- 10.0.24.11 Dynamic ETH E4:1D:2D:68:FD:26 mgmt0 10.0.27.254 Dynamic ETH 68:05:CA:17:3B:9A mgmt0 1.1.1.2 Dynamic ETH E4:1D:2D:3A:49:08 vlan 4000 MLNX1 [my-vip: master] (config) # sh ip route Flags: F: Failed to install in H/W B: BFD protected (static route) i: BFD session initializing (static route) x: protecting BFD session failed (static route) VRF Name default: -------------------------------------------------------------------------------------- Destination Mask Flag Gateway Interface Source AD/M -------------------------------------------------------------------------------------- 10.0.24.0 255.255.252.0 0.0.0.0 mgmt0 direct 0/0 1.1.1.0 255.255.255.252 0.0.0.0 vlan4000 direct 0/0 MLNX1 [my-vip: master] (config) # ping 10.0.24.10 PING 10.0.24.10 (10.0.24.10) 56(84) bytes of data. 64 bytes from 10.0.24.10: icmp_seq=1 ttl=64 time=0.110 ms ^C --- 10.0.24.10 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.110/0.110/0.110/0.000 ms MLNX1 [my-vip: master] (config) # ping 10.0.24.11 PING 10.0.24.11 (10.0.24.11) 56(84) bytes of data. 64 bytes from 10.0.24.11: icmp_seq=1 ttl=64 time=0.307 ms ^C --- 10.0.24.11 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.307/0.307/0.307/0.000 ms MLNX1 [my-vip: master] (config) # ping 10.0.24.12 PING 10.0.24.12 (10.0.24.12) 56(84) bytes of data. 64 bytes from 10.0.24.12: icmp_seq=1 ttl=64 time=0.128 ms 64 bytes from 10.0.24.12: icmp_seq=2 ttl=64 time=0.105 ms ^C --- 10.0.24.12 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 0.105/0.116/0.128/0.015 ms MLNX1 [my-vip: master] (config) # sh ip arp VRF Name: default Total number of entries: 3 -------------------------------------------------------------------------------------- Address Type Hardware Address Interface -------------------------------------------------------------------------------------- 10.0.24.11 Dynamic ETH E4:1D:2D:68:FD:26 mgmt0 10.0.27.254 Dynamic ETH 68:05:CA:17:3B:9A mgmt0 1.1.1.2 Dynamic ETH E4:1D:2D:3A:49:08 vlan 4000 MLNX1 [my-vip: master] (config) # sh mac-address-table --------------------------------------------------- Vlan Mac Address Type Port --------------------------------------------------- 20 00:00:5E:00:01:14 Dynamic Mpo100 20 F4:52:14:60:9B:E1 Dynamic Mpo100 20 F4:52:14:91:D7:91 Dynamic Mpo90 40 00:00:5E:00:01:28 Dynamic Mpo100 40 F4:52:14:60:9B:E1 Dynamic Mpo100 40 F4:52:14:91:D7:91 Dynamic Mpo90 50 00:00:5E:00:01:32 Dynamic Mpo100 50 F4:52:14:60:9B:E1 Dynamic Mpo100 50 F4:52:14:91:D7:91 Dynamic Mpo90 60 00:00:5E:00:01:3C Dynamic Mpo100 60 F4:52:14:60:9B:E1 Dynamic Mpo100 60 F4:52:14:91:D7:91 Dynamic Mpo90 80 00:00:5E:00:01:50 Dynamic Mpo100 80 F4:52:14:60:9B:E1 Dynamic Mpo100 80 F4:52:14:91:D7:91 Dynamic Mpo90 1000 00:00:5E:00:01:64 Dynamic Mpo100 1000 F4:52:14:60:9B:E1 Dynamic Mpo100 1000 F4:52:14:91:D7:91 Dynamic Mpo90 4000 E4:1D:2D:3A:49:08 Static Po1 Number of unicast: 19 Number of multicast: 0 MLNX1 [my-vip: master] (config) # sh mlag-vip MLAG-VIP: MLAG group name: my-vip MLAG VIP address: 10.0.24.12/22 Active nodes: 1 -------------------------------------------------------------- Hostname VIP-State IP Address -------------------------------------------------------------- MLNX2 master 10.0.24.10 MLNX1 [my-vip: master] (config) #