[0000.054] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level . [0000.062] I> MB1 (prd-version: 1.5.1.3-t194-41334769-d2a21c57) [0000.067] I> Boot-mode: Coldboot [0000.070] I> Chip revision : A02P [0000.073] I> Bootrom patch version : 15 (correctly patched) [0000.079] I> ATE fuse revision : 0x200 [0000.082] I> Ram repair fuse : 0x0 [0000.085] I> Ram Code : 0x2 [0000.088] I> rst_source : 0xb [0000.090] I> rst_level : 0x1 [0000.094] I> Boot-device: eMMC [0000.109] I> sdmmc DDR50 mode [0000.113] W> No valid slot number is found in scratch register [0000.118] W> Return default slot: _a [0000.122] I> Active Boot chain : 0 [0000.125] I> Boot-device: eMMC [0000.128] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.135] I> Temperature = 33000 [0000.138] W> Skipping boost for clk: BPMP_CPU_NIC [0000.142] W> Skipping boost for clk: BPMP_APB [0000.146] W> Skipping boost for clk: AXI_CBB [0000.150] W> Skipping boost for clk: AON_CPU_NIC [0000.154] W> Skipping boost for clk: CAN1 [0000.158] W> Skipping boost for clk: CAN2 [0000.162] I> Boot-device: eMMC [0000.165] I> Boot-device: eMMC [0000.173] I> Sdmmc: HS400 mode enabled [0000.177] I> ECC region[0]: Start:0x0, End:0x0 [0000.181] I> ECC region[1]: Start:0x0, End:0x0 [0000.185] I> ECC region[2]: Start:0x0, End:0x0 [0000.190] I> ECC region[3]: Start:0x0, End:0x0 [0000.194] I> ECC region[4]: Start:0x0, End:0x0 [0000.198] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.204] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.208] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.213] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.217] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.222] E> FAILED: Thermal config [0000.230] E> FAILED: MEMIO rail config [0000.248] I> Boot-device: eMMC [0000.258] I> sdmmc bdev is already initialized [0000.329] I> MB1 done ����main enter SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init �� [0000.337] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-2dfe4beb) [0000.338] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0000.338] I> Default Heap @ [0xd486400 - 0xd48a400] [0000.339] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0000.345] W> device prod register failed [0000.349] I> Boot-device: eMMC [0000.352] I> Boot_device: SDMMC_BOOT instance: 3 [0000.357] I> sdmmc-3 params source = boot args [0000.360] I> sdmmc bdev is already initialized [0000.365] I> sdmmc-3 params source = boot args [0000.371] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0000.378] I> Found 42 partitions in SDMMC_USER (instance 3) [0000.380] W> No valid slot number is found in scratch register [0000.385] W> Return default slot: _a [0000.389] I> Active Boot chain : 0 [0000.393] I> parsing oem signed section of bpmp-fw header done [0000.398] I> bpmp-fw binary init read from storage [0000.403] I> oem authentication of bpmp-fw header done [0000.409] I> bpmp-fw binary done read from storage [0000.412] I> bpmp-fw: Authentication init Done [0000.417] I> parsing oem signed section of cpubl header done [0000.422] I> cpubl binary init read from storage [0000.426] I> bpmp-fw: Authentication Finalize Done [0000.431] I> oem authentication of cpubl header done [0000.436] I> cpubl binary done read from storage [0000.440] I> cpubl: Authentication init Done [0000.445] I> parsing oem signed section of rce header done [0000.450] I> rce binary init read from storage [0000.454] I> Relocating BR-BCT [0000.457] I> cpubl: Authentication Finalize Done [0000.462] I> oem authentication of rce header done [0000.466] I> rce binary done read from storage [0000.470] I> rce: Authentication init Done [0000.475] I> parsing oem signed section of ape header done [0000.480] I> ape binary init read from storage [0000.484] I> rce: Authentication Finalize Done [0000.488] I> oem authentication of ape header done [0000.493] I> ape binary done read from storage [0000.497] I> ape: Authentication init Done [0000.502] I> parsing oem signed section of tos header done [0000.506] I> tos binary init read from storage [0000.511] I> ape: Authentication Finalize Done [0000.516] I> oem authentication of tos header done [0000.520] I> tos binary done read from storage [0000.524] I> tos: Authentication init Done [0000.528] I> parsing oem signed section of bpmp-fw-dtb header done [0000.534] I> bpmp-fw-dtb binary init read from storage [0000.539] I> tos: Authentication Finalize Done [0000.545] I> oem authentication of bpmp-fw-dtb header done [0000.551] I> bpmp-fw-dtb binary done read from storage [0000.554] I> bpmp-fw-dtb: Authentication init Done [0000.558] I> parsing oem signed section of cpubl-dtb header done [0000.564] I> cpubl-dtb binary init read from storage [0000.569] I> bpmp-fw-dtb: Authentication Finalize Done [0000.606] I> oem authentication of cpubl-dtb header done [0000.607] I> cpubl-dtb binary done read from storage [0000.607] I> cpubl-dtb: Authentication init Done [0000.609] I> parsing oem signed section of eks header done [0000.610] I> eks binary init read from storage [0000.610] I> cpubl-dtb: Authentication Finalize Done [0000.611] I> oem authentication of eks header done [0000.615] I> eks binary done read from storage [0000.619] I> eks: Authentication init Done [0000.623] I> eks: Authentication Finalize Done [0000.627] I> EKB detected (length: 0x410) @ VA:0x5270a400 ��NOTICE: BL31: v1.3(release):41d46a9cf NOTICE: BL31: Built : 21:14:52, Jun 25 2020 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 40: hwkey-agent is running!! hwkey-agent: 182: key_mgnt_processing ....... hwkey-agent: 157: Init hweky-agent services!! platform_bootstrap_epilog: trusty bootstrap complete �� welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is 57f8a77779f848bf2ecf21dabee5645f tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized 392 clocks registered WARNING: pll_c4 has no dyn ramp clk_mrq_init: mrq handler registered clk initialized nvlink initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized uphy_mrq_init: mrq handler registered uphy_dt initialized uphy initialized safereg_init: period 80 ms ec_late initialized mrq initialized �� [0001.131] I> Welcome to Cboot ��fmon_post initialized ��[0001.132] I> Cboot Version: t194-18fdfe28 [0001.132] I> CPU-BL Params @ 0xf2820000 [0001.133] I> 0) Base:0x00000000 Size:0x00000000 [0001.136] I> 1) Base:0xf1100000 Size:0x00100000 [0001.141] I> 2) Base:0xf2000000 Size:0x00200000 [0001.145] I> 3) Base:0xf1200000 Size:0x00200000 ��clk_set_parent failed for clk can1, parent pll_aon (-22) clk_set_parent failed for clk can2, parent pll_aon (-22) clk_set_parent failed for clk dmic5, parent pll_aon (-22) clk_set_parent failed for clk i2c2, parent pll_aon (-22) clk_set_parent failed for clk i2c8, parent pll_aon (-22) clk_set_parent failed for clk spi2, parent pll_aon (-22) clk_set_parent failed for clk pwm4, parent pll_aon (-22) clk_dt_late initialized machine_check initialized pm_post initialized dbells initialized avfs_clk_platform_post initialized dmce initialized cvc initialized ccplex_avfs_hw_init: nafll_cluster0: not monitored ccplex_avfs_hw_init: nafll_cluster1: not monitored ccplex_avfs_hw_init: nafll_cluster2: not monitored ccplex_avfs_hw_init: nafll_cluster3: not monitored avfs_clk_mach_post initialized regulator_post initialized rm initialized sc7_diag initialized thermal_test initialized serial_late initialized clk_post initialized clk_dt_post initialized mc_reg initialized pg_post initialized dyn_modules initialized sku_debugfs initialized speedo_debugfs initialized adc_debugfs initialized clk_debugfs initialized ��[0001.149] I> 4) Base:0xf1000000 Size:0x00100000 [0001.254] I> 5) Base:0xf0f00000 Size:0x00100000 [0001.259] I> 6) Base:0xf3800000 Size:0x00400000 [0001.263] I> 7) Base:0xf1c00000 Size:0x00400000 [0001.268] I> 8) Base:0xf0e00000 Size:0x00100000 [0001.272] I> 9) Base:0xf0d00000 Size:0x00100000 [0001.277] I> 10) Base:0xf3000000 Size:0x00800000 [0001.281] I> 11) Base:0x40000000 Size:0x00040000 [0001.286] I> 12) Base:0xf0c00000 Size:0x00100000��emc_debugfs initialized dvs_debugfs initialized �� [0001.295] I> 13) Base:0x40046000 Size:0x00002000 ��fmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized debugfs_cons initialized mail_fs initialized profile initialized cvc_debugfs initialized dmce_debugfs initialized ec_debugfs initialized rm_debugfs initialized soctherm_debug initialized gr_reader initialized mods initialized dt_fs initialized debugfs_mrq initialized debug_mrq initialized debug_safereg initialized initializing target calling apps_init() starting app shell entering main console loop ] ��[0001.299] I> 14) Base:0x40048000 Size:0x00002000 [0001.350] I> 15) Base:0xac000000 Size:0x00004000 [0001.354] I> 16) Base:0x4004a000 Size:0x00002000 [0001.359] I> 17) Base:0xf0b00000 Size:0x00100000 [0001.363] I> 18) Base:0x4004c000 Size:0x00002000 [0001.368] I> 19) Base:0xf2200000 Size:0x00600000 [0001.372] I> 20) Base:0x4004e000 Size:0x00002000 [0001.377] I> 21) Base:0xf09d0000 Size:0x0000c000 [0001.381] I> 22) Base:0x00000000 Size:0x00000000 [0001.385] I> 23) Base:0xf09e0000 Size:0x00020000 [0001.390] I> 24) Base:0xf6000000 Size:0x02000000 [0001.394] I> 25) Base:0x40050000 Size:0x00002000 [0001.399] I> 26) Base:0x40040000 Size:0x00006000 [0001.403] I> 27) Base:0xf1800000 Size:0x00400000 [0001.408] I> 28) Base:0xf4c00000 Size:0x01400000 [0001.412] I> 29) Base:0xf1400000 Size:0x00400000 [0001.417] I> 30) Base:0xf0a00000 Size:0x00100000 [0001.421] I> 31) Base:0x00000000 Size:0x00000000 [0001.426] I> 32) Base:0xf8000000 Size:0x08000000 [0001.430] I> 33) Base:0x00000000 Size:0x00000000 [0001.435] I> 34) Base:0xf3c00000 Size:0x01000000 [0001.439] I> 35) Base:0xab000000 Size:0x01000000 [0001.443] I> 36) Base:0xa0000000 Size:0x0b000000 [0001.448] I> 37) Base:0xf2800000 Size:0x00800000 [0001.452] I> 38) Base:0x80000000 Size:0x20000000 [0001.457] I> 39) Base:0xb0000000 Size:0x08000000 [0001.461] I> 40) Base:0x00000000 Size:0x00000000 [0001.466] I> 41) Base:0x00000000 Size:0x00000000 [0001.470] I> 42) Base:0x00000000 Size:0x00000000 [0001.475] I> 43) Base:0x00000000 Size:0x00000000 [0001.479] I> 44) Base:0x00000000 Size:0x00000000 [0001.484] I> 45) Base:0x00000000 Size:0x00000000 [0001.488] GIC-SPI Target CPU: 0 [0001.491] Interrupts Init done [0001.494] calling constructors [0001.497] initializing heap [0001.499] I> Heap: [0xa06905a8 ... 0xab000000] [0001.504] initializing threads [0001.507] initializing timers [0001.509] creating bootstrap completion thread [0001.514] top of bootstrap2() [0001.517] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000 [0001.521] initializing platform [0001.524] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0001.530] W> device prod register failed [0001.533] I> Bl_dtb @0xaaf00000 [0001.540] W> "plugin-manager" doesn't exist, creating [0001.541] W> "ids" doesn't exist, creating [0001.546] W> "connection" doesn't exist, creating [0001.550] W> "configs" doesn't exist, creating [0001.561] I> Find /i2c@3160000's alias i2c0 [0001.561] I> Reading eeprom i2c=0 address=0x50 [0001.588] I> Device at /i2c@3160000:0x50 [0001.588] I> Reading eeprom i2c=0 address=0x56 [0001.612] I> Device at /i2c@3160000:0x56 [0001.614] I> Find /i2c@3180000's alias i2c2 [0001.614] I> Reading eeprom i2c=2 address=0x54 [0001.616] E> I2C: slave not found in slaves. [0001.616] E> I2C: Could not write 0 bytes to slave: 0x00a8 with repeat start true. [0001.617] E> I2C_DEV: Failed to send register address 0x00000000. [0001.617] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa8 at 0. [0001.626] E> eeprom: Failed to read I2C slave device [0001.631] I> Eeprom read failed 0x3526070d [0001.635] I> Reading eeprom i2c=2 address=0x57 [0001.640] E> I2C: slave not found in slaves. [0001.644] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0001.651] E> I2C_DEV: Failed to send register address 0x00000000. [0001.657] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0. [0001.666] E> eeprom: Failed to read I2C slave device [0001.671] I> Eeprom read failed 0x3526070d [0001.675] I> Reading eeprom i2c=2 address=0x52 [0001.680] E> I2C: slave not found in slaves. [0001.684] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.692] E> I2C_DEV: Failed to send register address 0x00000000. [0001.697] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0. [0001.707] E> eeprom: Failed to read I2C slave device [0001.711] I> Eeprom read failed 0x3526070d [0001.716] I> Find /i2c@c240000's alias i2c1 [0001.719] I> Reading eeprom i2c=1 address=0x52 [0001.725] E> I2C: slave not found in slaves. [0001.728] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.736] E> I2C_DEV: Failed to send register address 0x00000000. [0001.741] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0. [0001.751] E> eeprom: Retry to read I2C slave device. [0001.756] E> I2C: slave not found in slaves. [0001.760] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.767] E> I2C_DEV: Failed to send register address 0x00000000. [0001.773] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0. [0001.782] E> eeprom: Failed to read I2C slave device [0001.787] I> Eeprom read failed 0x3526070d [0001.791] I> Reading eeprom i2c=1 address=0x50 [0001.796] E> I2C: slave not found in slaves. [0001.800] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.808] E> I2C_DEV: Failed to send register address 0x00000000. [0001.813] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0. [0001.823] E> eeprom: Retry to read I2C slave device. [0001.828] E> I2C: slave not found in slaves. [0001.831] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.839] E> I2C_DEV: Failed to send register address 0x00000000. [0001.845] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0. [0001.854] E> eeprom: Failed to read I2C slave device [0001.859] I> Eeprom read failed 0x3526070d [0001.863] I> create_pm_ids: id: 2888-0004-400-K, len: 15 [0001.868] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,t3 [0001.879] I> create_pm_ids: id: 2822-0000-700-J, len: 15 [0001.885] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,t3 [0001.896] I> Adding plugin-manager/ids/2888-0004-400=/i2c@3160000:module@0x50 [0001.904] W> "i2c@3160000" doesn't exist, creating [0001.907] W> "module@0x50" doesn't exist, creating [0001.912] I> Adding plugin-manager/ids/2822-0000-700=/i2c@3160000:module@0x56 [0001.919] W> "module@0x56" doesn't exist, creating [0001.926] I> Adding plugin-manager/cvm [0001.927] W> "chip-id" doesn't exist, creating [0001.931] I> Adding plugin-manager/chip-id/A02P [0001.936] I> Plugin-manager override starting [0001.941] I> node /plugin-manager/fragement-tegra-wdt-en matches [0001.949] I> node /plugin-manager/fragement-soft-wdt matches [0001.958] I> node /plugin-manager/fragment-pcie-c5-rp matches [0001.962] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0001.978] I> Disable plugin-manager status in FDT [0001.978] I> Plugin-manager override finished successfully [0001.978] I> gpio framework initialized [0001.980] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver [0001.985] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' drr [0001.992] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 [0001.999] E> fetch_driver_phandle_from_dt: failed to get node with compatible ti,9 [0002.007] E> fetch_driver_phandle_from_dt: failed to get node with compatible nxp9 [0002.013] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.019] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 [0002.027] E> fetch_driver_phandle_from_dt: failed to get node with compatible ti,9 [0002.035] E> fetch_driver_phandle_from_dt: failed to get node with compatible nxp9 [0002.041] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.049] I> fixed regulator driver initialized [0002.059] I> register 'maxim' power off handle [0002.060] I> virtual i2c enabled [0002.060] I> registered 'maxim,max20024' pmic [0002.063] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver [0002.070] I> Boot-device: eMMC [0002.073] I> Boot_device: SDMMC_BOOT instance: 3 [0002.081] I> sdmmc-3 params source = boot args [0002.082] I> create_pm_ids: id: 2888-0004-400-K, len: 15 [0002.087] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,t3 [0002.098] I> create_pm_ids: id: 2822-0000-700-J, len: 15 [0002.103] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,t3 [0002.114] I> sdmmc bdev is already initialized [0002.118] I> sdmmc-3 params source = boot args [0002.149] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0002.161] I> Found 42 partitions in SDMMC_USER (instance 3) [0002.171] I> enabling 'vdd-hdmi-5v0' regulator [0002.176] I> regulator 'vdd-hdmi-5v0' already enabled [0002.176] I> hdmi cable connected [0002.178] W> set volts not configured for 'vdd-1v0' [0002.180] W> set volts not configured for 'vdd-1v8-hs' [0002.184] E> invalid display type [0002.187] E> invalid display type [0002.189] E> cannot find any other nvdisp nodes [0002.204] I> edid read success [0002.216] I> edid read success [0002.216] I> width = 640, height = 480, frequency = 25174825 [0002.217] I> width = 640, height = 480, frequency = 25174825 [0002.217] I> width = 1920, height = 1080, frequency = 148500000 [0002.218] I> width = 1920, height = 1080, frequency = 148500000 [0002.218] I> width = 1920, height = 1080, frequency = 148351648 [0002.222] I> width = 1920, height = 1080, frequency = 148351648 [0002.228] I> width = 640, height = 480, frequency = 25174825 [0002.234] I> width = 720, height = 480, frequency = 26973026 [0002.239] I> width = 720, height = 480, frequency = 26973026 [0002.245] I> width = 720, height = 576, frequency = 26973026 [0002.250] I> width = 1280, height = 720, frequency = 74175824 [0002.256] I> width = 1280, height = 720, frequency = 74175824 [0002.261] I> Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.271] I> hdmi_enable, starting HDMI initialisation [0002.277] I> hdmi_enable, HDMI initialisation complete [0002.286] I> Load in CBoot Boot Options partition and parse it [0002.293] E> Error -9 when finding node with path /boot-configuration [0002.293] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO file. [0002.297] I> Hit any key to stop autoboot: 4 3 2 1 [0004.305] initializing target [0004.305] calling apps_init() [0004.306] starting app kernel_boot_app [0004.325] I> found decompressor handler: lz4-legacy [0004.326] I> decompressing BMP blob ... [0004.330] I> Kernel type = Normal [0004.330] I> Loading kernel-bootctrl from partition [0004.330] I> Loading partition kernel-bootctrl at 0xa4ac0000 from device(0x1) [0004.337] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0004.337] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0004.338] I> ########## SD boot ########## [0004.342] I> No sdcard [0004.344] I> -0 params source = [0004.347] E> Blockdev open: exit error [0004.350] E> SD boot failed, err: 724238353 [0004.354] I> ########## USB boot ########## [0004.363] W> No valid slot number is found in scratch register [0004.364] W> Return default slot: _a [0004.380] I> USB Firmware Version: 60.06 release [0004.435] I> regulator of usb2-0 already enabled [0004.441] I> regulator of usb2-1 already enabled [0004.447] I> regulator of usb2-2 already enabled [0004.455] I> enabling 'vdd-5v-sata' regulator [0005.522] I> USB 2.0 port 2 new high-speed USB device detected [0005.524] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa0e9f800, c0 [0005.524] E> slot id is 1 [0005.526] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa0e9f800, c0 [0005.530] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa0e9f800, c0 [0005.535] I> [0005.535] I> Enumerated USB Device 1a40:0801 [0005.539] I> [0005.541] E> Enumerated device doesn't belong to MSD class or protocol is not bul! [0005.549] E> USBMSD: Failed to initialize Enumerated USB device either not an MSD. [0005.563] E> Error opening USBMSD driver 0, err: 7c7c0312 [0005.568] E> Failed to initialize device 5-0 [0005.572] E> USB boot failed, err: 2088502034 [0005.577] I> ########## Fixed storage boot ########## [0005.581] I> Already published: 00010003 [0005.585] I> Look for boot partition [0005.589] I> Fallback: assuming 0th partition is boot partition [0005.594] I> Detect filesystem [0005.622] I> Loading extlinux.conf ... [0005.622] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf [0005.665] I> L4T boot options [0005.665] I> [1]: "primary kernel" [0005.665] I> Enter choice: [0008.666] I> Continuing with default option: 1 [0008.666] I> Loading kernel sig file from rootfs ... [0008.666] I> rootfs path: /sdmmc_user/boot/Image.sig [0008.685] I> Loading kernel binary from rootfs ... [0008.685] I> rootfs path: /sdmmc_user/boot/Image [0008.927] I> Validate kernel ... [0008.928] I> T19x: Authenticate kernel (bin_type: 37), max size 0x5000000 [0009.259] I> No kernel-dtb binary path [0009.259] W> No valid slot number is found in scratch register [0009.259] W> Return default slot: _a [0009.260] I> A/B: bin_type (38) slot 0 [0009.260] I> Loading kernel-dtb from partition [0009.260] I> Loading partition kernel-dtb at 0x91000000 from device(0x1) [0009.269] I> Validate kernel-dtb ... [0009.269] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x400000 [0009.274] I> Loading ramdisk from rootfs ... [0009.275] I> rootfs path: /sdmmc_user/boot/initrd [0009.327] I> Kernel hdr @0xa4ac0000 [0009.328] I> Kernel dtb @0x90000000 [0009.328] I> decompressor handler not found [0009.328] I> Copying kernel image (34361360 bytes) from 0xa4ac0000 to 0x80080000 e [0009.339] I> Updated bpmp info to DTB [0009.340] I> Ramdisk: Base: 0x92000000; Size: 0x54ecaf [0009.341] I> Updated initrd info to DTB [0009.341] W> WARN: Fail to override "console=none" in commandline [0009.341] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0009.348] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0009.355] W> No valid slot number is found in scratch register [0009.361] W> Return default slot: _a [0009.364] I> Active slot suffix: [0009.367] I> add_boot_slot_suffix: slot_suffix = [0009.372] I> Linux Cmdline: console=ttyTCU0,115200 video=tegrafb no_console_suspe [0009.401] I> Updated bootarg info to DTB [0009.405] W> MAC addr invalid! [0009.408] E> Failed to get WIFI MAC address [0009.412] W> MAC addr invalid! [0009.415] E> Failed to get Bluetooth MAC address [0009.419] I> eeprom_get_mac_addr: MAC (type: 2): 00:04:4b:e5:92:81 [0009.426] W> "plugin-manager" doesn't exist, creating [0009.430] I> Adding /chosen/plugin-manager/cvm [0009.435] W> "chip-id" doesn't exist, creating [0009.439] I> Adding /chosen/plugin-manager/chip-id [0009.444] W> "configs" doesn't exist, creating [0009.448] I> Adding /chosen/plugin-manager/configs [0009.452] W> "ids" doesn't exist, creating [0009.456] I> Adding /chosen/plugin-manager/ids [0009.461] W> "odm-data" doesn't exist, creating [0009.465] I> Adding /chosen/plugin-manager/odm-data [0009.473] W> "memory" doesn't exist, creating [0009.474] I> [0] START: 0x80000000, END: 0xac000000 [0009.479] I> [1] START: 0xac004000, END: 0xf09d0000 [0009.483] I> [2] START: 0xf09dc000, END: 0xf09e0000 [0009.488] I> dram_block larger than 80000000 [0009.492] I> [3] START: 0x100000000, END: 0x880000000 [0009.497] I> added [base:0x80000000, size:0x2c000000] to /memory [0009.503] I> added [base:0xac200000, size:0x44600000] to /memory [0009.509] I> added [base:0x100000000, size:0x780000000] to /memory [0009.516] I> Updated memory info to DTB [0009.519] E> add_disp_param: failed to get display params for du=1 [0009.525] W> "reset" doesn't exist, creating [0009.529] I> NVG: Logical CPU: 0; MPIDR: 0x80000000 [0009.533] I> NVG: Logical CPU: 1; MPIDR: 0x80000001 [0009.538] I> NVG: Logical CPU: 2; MPIDR: 0x80000100 [0009.543] I> NVG: Logical CPU: 3; MPIDR: 0x80000101 [0009.548] I> NVG: Logical CPU: 4; MPIDR: 0x80000200 [0009.552] I> NVG: Logical CPU: 5; MPIDR: 0x80000201 [0009.557] I> NVG: Logical CPU: 6; MPIDR: 0x80000300 [0009.562] I> NVG: Logical CPU: 7; MPIDR: 0x80000301 [0009.567] W> "misc-data" doesn't exist, creating [0009.571] I> Boot-device: eMMC [0009.574] I> Add boot-sdmmc to plugin-manager/misc-data [0009.579] I> Add storage-sdmmc to plugin-manager/misc-data [0009.584] W> Unknown storage device [0009.588] I> Add serial number:1421220031161 as DT property [0009.594] I> Plugin-manager override starting [0009.598] I> node /plugin-manager/fragement-tegra-wdt-en matches [0009.605] I> node /plugin-manager/fragement-soft-wdt matches [0009.612] I> node /plugin-manager/fragment-pcie-c5-rp matches [0009.616] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0009.626] I> Disable plugin-manager status in FDT [0009.627] I> Plugin-manager override finished successfully [0009.631] I> tegrabl_load_kernel_and_dtb: Done [0009.652] I> Kernel EP: 0x80080000, DTB: 0x90000000 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-rt93-tegra (root@Prasanna-GRL) (gcc version 71 [ 0.000000] Boot CPU: AArch64 Processor [4e0f0040] [ 0.000000] OF: fdt:memory scan node memory, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 2c000000 [ 0.000000] OF: fdt: - ac200000 , 44600000 [ 0.000000] OF: fdt: - 100000000 , 780000000 [ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '') ��WARNING: pll_d3 has no dyn ramp ��[ 6.160893] cgroup: cgroup2: unknown option "nsdelegate" [ 10.327076] random: crng init done [ 10.327203] random: 7 urandom warning(s) missed due to ratelimiting [ 14.840277] using random self ethernet address [ 14.841583] using random host ethernet address [ 15.305993] using random self ethernet address [ 15.307326] using random host ethernet address Ubuntu 18.04.4 LTS jetson ttyTCU0