[0000.341] I> Welcome to MB2(TBoot-BPMP)(version: 01.00.160913-t186-M-00.00-mobile-c700205d) [0000.349] I> bit @ 0xd480000 [0000.352] I> Boot-device: eMMC [0000.359] I> sdmmc bdev is already initialized [0000.364] I> pmic: reset reason (nverc) : 0x44 [0000.396] I> Found 19 partitions in SDMMC_BOOT (instance 3) [0000.415] I> Found 33 partitions in SDMMC_USER (instance 3) [0000.421] I> MB2 check ECC error: EMC_INTSTATUS_0: 0x10 [0000.426] I> MB2 check ECC error: EMC_INTSTATUS_0: 0x0 [0000.431] I> MB2 check ECC error: EMC_INTSTATUS_0: 0x10 [0000.436] I> MB2 check ECC error: EMC_INTSTATUS_0: 0x0 [0000.441] I> OEM carveouts init scrub in progress... [0000.517] I> MB2 check ECC error: EMC_INTSTATUS_0: 0x10 [0000.522] I> MB2 check ECC error: EMC_INTSTATUS_0: 0x0 [0000.527] I> MB2 check ECC error: EMC_INTSTATUS_0: 0x10 [0000.532] I> MB2 check ECC error: EMC_INTSTATUS_0: 0x0 [0000.537] I> Mb2 SDRAM scrub successful [0000.541] W> No valid slot number is found in scratch register [0000.546] W> Return default slot: _a [0000.550] I> A/B: bin_type (16) slot 0 [0000.553] I> Loading partition bpmp-fw at 0xd7800000 [0000.558] I> Reading two headers - addr:0xd7800000 blocks:1 [0000.564] I> Addr: 0xd7800000, start-block: 58777608, num_blocks: 1 [0000.589] I> Binary(16) of size 533504 is loaded @ 0xd7800000 [0000.594] W> No valid slot number is found in scratch register [0000.600] W> Return default slot: _a [0000.603] I> A/B: bin_type (17) slot 0 [0000.607] I> Loading partition bpmp-fw-dtb at 0xd79f0000 [0000.612] I> Reading two headers - addr:0xd79f0000 blocks:1 [0000.618] I> Addr: 0xd79f0000, start-block: 58780024, num_blocks: 1 [0000.637] I> Binary(17) of size 75760 is loaded @ 0xd79ed600 [0000.672] I> Loading SCE-FW ... [0000.675] W> No valid slot number is found in scratch register [0000.680] W> Return default slot: _a [0000.684] I> A/B: bin_type (12) slot 0 [0000.687] I> Loading partition sce-fw at 0xd7300000 [0000.692] I> Reading two headers - addr:0xd7300000 blocks:1 [0000.697] I> Addr: 0xd7300000, start-block: 58784120, num_blocks: 1 [0000.717] I> Binary(12) of size 125168 is loaded @ 0xd7300000 [0000.722] I> Init SCE [0000.725] I> Loading APE-FW ... [0000.728] W> No valid slot number is found in scratch register [0000.733] W> Return default slot: _a [0000.737] I> A/B: bin_type (11) slot 0 [0000.740] I> Loading partition adsp-fw at 0xd7400000 [0000.745] I> Reading two headers - addr:0xd7400000 blocks:1 [0000.751] I> Addr: 0xd7400000, start-block: 58761224, num_blocks: 1 [0000.770] I> Binary(11) of size 107808 is loaded @ 0xd7400000 [0000.776] I> Copy BTCM section [0000.779] W> No valid slot number is found in scratch register [0000.784] W> Return default slot: _a [0000.788] I> A/B: bin_type (13) slot 0 [0000.791] I> Loading partition cpu-bootloader at 0x96000000 [0000.797] I> Reading two headers - addr:0x96000000 blocks:1 [0000.802] I> Addr: 0x96000000, start-block: 58740744, num_blocks: 1 [0000.824] I> Binary(13) of size 284816 is loaded @ 0x96000000 [0000.829] W> No valid slot number is found in scratch register [0000.835] W> Return default slot: _a [0000.838] I> A/B: bin_type (20) slot 0 [0000.842] I> Loading partition bootloader-dtb at 0x8520f400 [0000.847] I> Reading two headers - addr:0x8520f400 blocks:1 [0000.853] I> Addr: 0x8520f400, start-block: 58742792, num_blocks: 1 [0000.875] I> Binary(20) of size 364400 is loaded @ 0x8520f400 [0000.881] W> No valid slot number is found in scratch register [0000.887] W> Return default slot: _a [0000.890] I> A/B: bin_type (14) slot 0 [0000.894] I> Loading partition secure-os at 0x8530f600 [0000.899] I> Reading two headers - addr:0x8530f600 blocks:1 [0000.904] I> Addr: 0x8530f600, start-block: 58744840, num_blocks: 1 [0000.926] I> Binary(14) of size 366000 is loaded @ 0x8530f600 [0000.934] I> TOS boot-params @ 0x85000000 [0000.938] I> TOS params prepared [0000.941] I> Loading EKS ... [0000.944] I> A/B: bin_type (15) slot 0 [0000.947] I> Loading partition eks at 0x8590f800 [0000.952] I> Reading two headers - addr:0x8590f800 blocks:1 [0000.957] I> Addr: 0x8590f800, start-block: 58757128, num_blocks: 1 [0000.976] I> Binary(15) of size 1040 is loaded @ 0x8590f800 [0000.982] I> EKB detected (length: 0x400) @ 0x8590f800 [0000.987] I> Copied encrypted keys [0000.990] I> boot profiler @ 0x235844000 [0000.994] I> boot profiler for TOS @ 0x235844000 [0000.999] I> Unhalting SCE [0001.002] I> Primary Memory Start:80000000 Size:70000000 [0001.007] I> Extended Memory Start:f0110000 Size:1456f0000 [0001.014] I> MB2(TBoot-BPMP) done NOTICE: BL31: v1.3(release):41d46a9cf NOTICE: BL31: Built : 21:14:44, Jun 25 2020 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 40: hwkey-agent is running!! hwkey-agent: 182: key_mgnt_processing ....... hwkey-agent: 157: Init hweky-agent services!! platform_bootstrap_epilog: trusty bootstrap complete [0001.218] I> Welcome to Cboot [0001.221] I> Cboot Version: t186-02737b3e [0001.225] I> CPU-BL Params @ 0x235800000 [0001.229] I> Dram Scrub in progress [0001.872] I> DRAM Scrub Successful [0001.876] I> 0) Base:0x00000000 Size:0x00000000 [0001.880] I> 1) Base:0x237f00000 Size:0x00100000 [0001.884] I> 2) Base:0x237e00000 Size:0x00100000 [0001.889] I> 3) Base:0x237d00000 Size:0x00100000 [0001.894] I> 4) Base:0x237c00000 Size:0x00100000 [0001.898] I> 5) Base:0x237b00000 Size:0x00100000 [0001.903] I> 6) Base:0x237800000 Size:0x00200000 [0001.907] I> 7) Base:0x237400000 Size:0x00400000 [0001.912] I> 8) Base:0x237a00000 Size:0x00100000 [0001.916] I> 9) Base:0x237300000 Size:0x00100000 [0001.921] I> 10) Base:0x236800000 Size:0x00800000 [0001.925] I> 11) Base:0x30000000 Size:0x00040000 [0001.930] I> 12) Base:0xf0000000 Size:0x00100000 [0001.934] I> 13) Base:0x30040000 Size:0x00001000 [0001.938] I> 14) Base:0x30048000 Size:0x00001000 [0001.943] I> 15) Base:0x30049000 Size:0x00001000 [0001.947] I> 16) Base:0x3004a000 Size:0x00001000 [0001.952] I> 17) Base:0x3004b000 Size:0x00001000 [0001.956] I> 18) Base:0x3004c000 Size:0x00001000 [0001.961] I> 19) Base:0x3004d000 Size:0x00001000 [0001.965] I> 20) Base:0x3004e000 Size:0x00001000 [0001.969] I> 21) Base:0x3004f000 Size:0x00001000 [0001.974] I> 22) Base:0x00000000 Size:0x00000000 [0001.978] I> 23) Base:0xf0100000 Size:0x00010000 [0001.983] I> 24) Base:0x00000000 Size:0x00000000 [0001.987] I> 25) Base:0x00000000 Size:0x00000000 [0001.992] I> 26) Base:0x00000000 Size:0x00000000 [0001.996] I> 27) Base:0x00000000 Size:0x00000000 [0002.000] I> 28) Base:0x84400000 Size:0x00400000 [0002.005] I> 29) Base:0x30000000 Size:0x00010000 [0002.009] I> 30) Base:0x238000000 Size:0x08000000 [0002.014] I> 31) Base:0x00000000 Size:0x00000000 [0002.018] I> 32) Base:0x236000000 Size:0x00600000 [0002.023] I> 33) Base:0x80000000 Size:0x70000000 [0002.027] I> 34) Base:0xf0110000 Size:0x1456f0000 [0002.032] I> 35) Base:0x00000000 Size:0x00000000 [0002.036] I> 36) Base:0x00000000 Size:0x00000000 [0002.041] I> 37) Base:0x2372e0000 Size:0x00020000 [0002.045] I> 38) Base:0x84000000 Size:0x00400000 [0002.049] I> 39) Base:0x96000000 Size:0x02000000 [0002.054] I> 40) Base:0x85000000 Size:0x01200000 [0002.058] I> 41) Base:0x235800000 Size:0x00500000 [0002.063] I> 42) Base:0x00000000 Size:0x00000000 [0002.067] I> 43) Base:0x00000000 Size:0x00000000 [0002.072] GIC-SPI Target CPU: 4 [0002.075] Interrupts Init done [0002.078] calling constructors [0002.081] initializing heap [0002.084] initializing threads [0002.087] initializing timers [0002.090] creating bootstrap completion thread [0002.095] top of bootstrap2() [0002.098] CPU: ARM Cortex A57 [0002.101] CPU: MIDR: 0x411FD073, MPIDR: 0x80000100 [0002.106] initializing platform [0002.110] I> Bl_dtb @0x8520f400 [0002.113] I> gpio framework initialized [0002.119] I> tegrabl_gpio_driver_register: register 'nvidia,tegra186-gpio' driver [0002.129] I> tegrabl_gpio_driver_register: register 'nvidia,tegra186-gpio-aon' driver [0002.137] I> GPIO framework and drivers are initialized. [0002.142] I> Boot-device: eMMC [0002.149] I> sdmmc bdev is already initialized [0002.179] I> Found 19 partitions in SDMMC_BOOT (instance 3) [0002.197] I> Found 33 partitions in SDMMC_USER (instance 3) [0002.202] W> opt-in fuse is not set, skip fuse_burning [0002.207] I> Reserved memory at 0xfbe00000 for U-Boot relocation [0002.213] W> No valid slot number is found in scratch register [0002.219] W> Return default slot: _a [0002.222] I> A/B: bin_type (21) slot 0 [0002.226] I> Loading kernel-dtb from partition [0002.230] I> Loading partition kernel-dtb at 0x80000000 from device(0x1) [0002.247] I> Kernel_dtb @0x80000000 [0002.250] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xee [0002.261] I> tegrabl_gpio_driver_register: register 'tca9539_gpio_driver' driver [0002.268] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xe8 [0002.277] I> tegrabl_gpio_driver_register: register 'tca9539_gpio_driver' driver [0002.287] I> fixed regulator driver initialized [0002.320] I> register 'maxim' power off handle [0002.326] I> virtual i2c enabled [0002.329] I> registered 'maxim,max77620' pmic [0002.333] I> tegrabl_gpio_driver_register: register 'max77620-gpio' driver [0002.347] I> Find /i2c@c250000's alias i2c7 [0002.351] I> Reading eeprom i2c=7 address=0x50 [0002.380] I> Device at /i2c@c250000:0x50 [0002.384] I> Reading eeprom i2c=7 address=0x57 [0002.412] I> Device at /i2c@c250000:0x57 [0002.417] I> Find /i2c@c240000's alias i2c1 [0002.421] I> Reading eeprom i2c=1 address=0x51 [0002.426] E> I2C: slave not found in slaves. [0002.430] E> I2C: Could not write 0 bytes to slave: 0x00a2 with repeat start true. [0002.438] E> I2C_DEV: Failed to send register address 0x00000000. [0002.444] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa2 at 0x00000000 via instance 1. [0002.453] E> eeprom: Retry to read I2C slave device. [0002.458] E> I2C: slave not found in slaves. [0002.462] E> I2C: Could not write 0 bytes to slave: 0x00a2 with repeat start true. [0002.470] E> I2C_DEV: Failed to send register address 0x00000000. [0002.476] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa2 at 0x00000000 via instance 1. [0002.485] E> eeprom: Failed to read I2C slave device [0002.490] I> Eeprom read failed 0x3526070d [0002.494] I> Find /i2c@3160000's alias i2c0 [0002.498] I> Reading eeprom i2c=0 address=0x50 [0002.503] E> I2C: slave not found in slaves. [0002.507] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0002.514] E> I2C_DEV: Failed to send register address 0x00000000. [0002.520] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 0. [0002.530] E> eeprom: Failed to read I2C slave device [0002.535] I> Eeprom read failed 0x3526070d [0002.539] I> Find /i2c@3180000's alias i2c2 [0002.543] I> Reading eeprom i2c=2 address=0x54 [0002.548] I> Enabling gpio chip_id = 2, gpio pin = 9 [0002.578] I> Disabling gpio chip_id = 2, gpio pin = 9 [0002.583] I> Device at /i2c@3180000:0x54 [0002.587] I> Reading eeprom i2c=2 address=0x57 [0002.591] I> Enabling gpio chip_id = 2, gpio pin = 9 [0002.597] E> I2C: slave not found in slaves. [0002.601] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0002.609] E> I2C_DEV: Failed to send register address 0x00000000. [0002.615] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 2. [0002.624] E> eeprom: Failed to read I2C slave device [0002.629] I> Disabling gpio chip_id = 2, gpio pin = 9 [0002.634] I> Eeprom read failed 0x00000000 [0002.638] I> create_pm_ids: id: 3489-0000-300-N, len: 15 [0002.643] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.654] I> create_pm_ids: id: 2597-0000-501-C, len: 15 [0002.659] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.670] I> create_pm_ids: id: 3326-1000-100-M, len: 15 [0002.675] I> config: mem-type:ff,power-config:ff,misc-config:ff,modem-config:ff,touch-config:ff,display-config:ff,, len: 93 [0002.710] I> enabling 'vdd-hdmi' regulator [0002.726] I> regulator 'vdd-hdmi' already enabled [0002.730] I> hdmi cable connected [0002.739] I> setting 'vdd-pex-1v00' regulator to 1000000 micro volts [0002.751] I> setting 'vdd-1v8' regulator to 1800000 micro volts [0002.759] E> cannot find any other nvdisp nodes [0002.781] I> edid read success [0002.796] I> edid read success [0002.799] I> width = 640, height = 480, frequency = 25174825 [0002.804] I> width = 1920, height = 1080, frequency = 148500000 [0002.810] I> width = 1920, height = 1080, frequency = 148500000 [0002.816] I> width = 1920, height = 1080, frequency = 148351648 [0002.821] I> width = 1920, height = 1080, frequency = 148351648 [0002.827] I> width = 1280, height = 720, frequency = 74175824 [0002.833] I> width = 1280, height = 720, frequency = 74175824 [0002.838] I> width = 720, height = 480, frequency = 26973026 [0002.844] I> width = 720, height = 576, frequency = 26973026 [0002.849] I> width = 720, height = 480, frequency = 26973026 [0002.855] I> width = 720, height = 576, frequency = 26973026 [0002.860] I> width = 640, height = 480, frequency = 25174825 [0002.865] I> Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.876] I> hdmi_enable, starting HDMI initialisation [0002.883] I> hdmi_enable, HDMI initialisation complete [0002.896] initializing target [0002.899] calling apps_init() [0002.902] starting app kernel_boot_app [0002.924] I> found decompressor handler: lz4-legacy [0002.929] I> decompressing BMP blob ... [0002.939] I> Kernel type = Normal [0002.942] I> Loading kernel-bootctrl from partition [0002.947] I> Loading partition kernel-bootctrl at 0xa8000000 from device(0x1) [0002.962] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0002.969] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0002.975] I> ########## Fixed storage boot ########## [0002.980] W> No valid slot number is found in scratch register [0002.986] W> Return default slot: _a [0002.989] I> A/B: bin_type (24) slot 0 [0003.005] I> Boot image size read from image header: 74aba [0003.010] I> Boot image load address: 0x80400000 [0003.015] I> Loading kernel from partition [0003.019] I> Loading partition kernel at 0x80400000 from device(0x1) [0003.979] I> Validate kernel ... [0003.982] I> T18x: Authenticate kernel (bin_type 24), max size 0x4000000 [0003.989] I> kernel-dtb is already loaded [0003.993] I> Validate kernel-dtb ... [0003.997] I> T18x: Authenticate kernel-dtb (bin_type 21), max size 0x100000 [0004.004] I> Checking boot.img header magic ... [0004.008] I> [OK] [0004.010] I> Kernel hdr @0x80400000 [0004.013] I> Kernel dtb @0x80000000 [0004.017] I> decompressor handler not found [0004.021] I> Copying kernel image (477882 bytes) from 0x80400800 to 0x80600000 ... [0004.028] I> Done [0004.030] I> Move ramdisk (len: 0) from 0x80475800 to 0x947b0000 [0004.037] I> Updated bpmp info to DTB [0004.043] I> Ramdisk: Base: 0x947b0000; Size: 0x0 [0004.048] I> Updated initrd info to DTB [0004.051] W> WARN: Fail to override "console=none" in commandline [0004.057] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0004.064] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0004.072] I> disabled_core_mask: 0xffffff0c [0004.076] W> No valid slot number is found in scratch register [0004.081] W> Return default slot: _a [0004.085] I> Active slot suffix: [0004.088] I> add_boot_slot_suffix: slot_suffix = [0004.092] I> Linux Cmdline: console=ttyS0,115200 androidboot.presilicon=true firmware_class.path=/etc/firmware root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=m [0004.142] I> Updated bootarg info to DTB [0004.146] I> eeprom_get_mac_addr: MAC (type: 0): 00:ff:ff:ff:ff:ff [0004.152] I> eeprom_get_mac_addr: MAC (type: 1): 00:ff:ff:ff:ff:ff [0004.158] I> eeprom_get_mac_addr: MAC (type: 2): 00:04:4b:a9:31:b4 [0004.165] E> Found no plugin manager ids in source DT [0004.170] W> Add plugin manager ids from board info [0004.174] W> "plugin-manager" doesn't exist, creating [0004.179] W> "ids" doesn't exist, creating [0004.183] W> "connection" doesn't exist, creating [0004.188] W> "configs" doesn't exist, creating [0004.192] I> create_pm_ids: id: 3489-0000-300-N, len: 15 [0004.197] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0004.208] I> create_pm_ids: id: 2597-0000-501-C, len: 15 [0004.213] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0004.224] I> create_pm_ids: id: 3326-1000-100-M, len: 15 [0004.229] I> config: mem-type:ff,power-config:ff,misc-config:ff,modem-config:ff,touch-config:ff,display-config:ff,, len: 93 [0004.240] I> Adding plugin-manager/ids/3489-0000-300=/i2c@c250000:module@0x50 [0004.247] W> "i2c@c250000" doesn't exist, creating [0004.252] W> "module@0x50" doesn't exist, creating [0004.257] I> Adding plugin-manager/ids/2597-0000-501=/i2c@c250000:module@0x57 [0004.264] W> "module@0x57" doesn't exist, creating [0004.269] I> Adding plugin-manager/ids/3326-1000-100=/i2c@3180000:module@0x54 [0004.277] W> "i2c@3180000" doesn't exist, creating [0004.281] W> "module@0x54" doesn't exist, creating [0004.288] I> Adding plugin-manager/ids/3489-0000-300-N [0004.295] I> Adding plugin-manager/configs/3489-mem-type 00 [0004.301] I> Adding plugin-manager/configs/3489-power-config 00 [0004.307] I> Adding plugin-manager/configs/3489-misc-config 00 [0004.312] I> Adding plugin-manager/configs/3489-modem-config 00 [0004.318] I> Adding plugin-manager/configs/3489-touch-config 00 [0004.324] I> Adding plugin-manager/configs/3489-display-config 00 [0004.330] I> Adding plugin-manager/cvm [0004.334] W> "chip-id" doesn't exist, creating [0004.339] I> Adding plugin-manager/chip-id/A02P [0004.343] W> "odm-data" doesn't exist, creating [0004.348] I> Adding /chosen/plugin-manager/odm-data [0004.357] I> added [base:0x80000000, size:0x70000000] to /memory [0004.363] I> added [base:0xf0200000, size:0x145600000] to /memory [0004.369] I> added [base:0x235e00000, size:0x200000] to /memory [0004.375] I> added [base:0x236600000, size:0x200000] to /memory [0004.381] I> added [base:0x237000000, size:0x200000] to /memory [0004.386] I> Updated memory info to DTB [0004.391] E> add_disp_param: failed to get display params for du=1 [0004.399] W> "reset" doesn't exist, creating [0004.403] W> "pmc-reset-reason" doesn't exist, creating [0004.408] W> "pmic-reset-reason" doesn't exist, creating [0004.415] I> Adding ecid(00000001645102840400000009008100) to DT [0004.421] I> disabled_core_mask: 0xffffff0c [0004.433] I> Add serial number:0424718002198 as DT property [0004.442] I> Plugin-manager override starting [0004.448] I> node /plugin-manager/fragement@0 matches [0004.458] I> node /plugin-manager/fragement@4 matches [0004.495] I> node /plugin-manager/fragment-e3326@0 matches [0004.577] I> node /plugin-manager/fragment-p3310-c00-camera matches [0004.604] I> Disable plugin-manager status in FDT [0004.608] I> Plugin-manager override finished successfully [0004.613] I> tegrabl_load_kernel_and_dtb: Done [0004.659] I> Kernel EP: 0x80600000, DTB: 0x80000000 U-Boot 2016.07-ge6da093be3 (Jun 25 2020 - 21:14:32 -0700) TEGRA186 Model: NVIDIA P2771-0000-500 DRAM: 6.8 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@2490000 Hit any key to stop autoboot: 0 MMC: no card present switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 857 bytes read in 136 ms (5.9 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 5565615 bytes read in 267 ms (19.9 MiB/s) Retrieving file: /boot/Image 34330632 bytes read in 862 ms (38 MiB/s) append: console=ttyS0,115200 androidboot.presilicon=true firmware_class.path=/etc/firmware root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 is ## Flattened Device Tree blob at 80000000 Booting using the fdt blob at 0x80000000 reserving fdt memory region: addr=80000000 size=10000 Using Device Tree in place at 0000000080000000, end 000000008005df03 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x100 [ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-3357) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SM0 [ 0.000000] Boot CPU: AArch64 Processor [411fd073] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 16416, [ 0.000000] OF: fdt: - 80000000 , 70000000 [ 0.000000] OF: fdt: - f0200000 , 145600000 [ 0.000000] OF: fdt: - 235e00000 , 200000 [ 0.000000] OF: fdt: - 236600000 , 200000 [ 0.000000] OF: fdt: - 237000000 , 200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000003100000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] Found tegra_fbmem2: 00800000@9607d000 [ 0.000000] Found lut_mem2: 00002008@9607a000 [ 0.998611] pre_t19x_iso_plat_register(): iso bandwidth 5924200KB is not available, client disp_0 [ 0.998638] pre_t19x_iso_plat_register(): iso bandwidth 3136300KB is not available, client disp_0 [ 3.961482] cgroup: cgroup2: unknown option "nsdelegate" [ 4.935481] using random self ethernet address [ 4.940185] using random host ethernet address [ 5.329984] using random self ethernet address [ 5.334828] using random host ethernet address [ 7.199683] Please complete system configuration setup on desktop to proceed... [ 218.928981] CPU1: shutdown [ 218.997055] CPU2: shutdown Ubuntu 18.04.4 LTS elma ttyS0 elma login: [ 227.149348] using random self ethernet address [ 227.154260] using random host ethernet address [ 227.417249] using random self ethernet address [ 227.421742] using random host ethernet address