Boot with 1.8V connected ######******************************** яв [0000.084] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 1 from HW fuses. [0000.093] I> MB1 (prd-version: 1.5.1.0-t194-41334769-59d8a47d) [0000.098] I> Boot-mode: Coldboot [0000.101] I> Chip revision : A02 [0000.104] I> Bootrom patch version : 7 (correctly patched) [0000.109] I> ATE fuse revision : 0x200 [0000.113] I> Ram repair fuse : 0x0 [0000.116] I> Ram Code : 0x0 [0000.118] I> rst_source : 0x0 [0000.121] I> rst_level : 0x0 [0000.125] I> Boot-device: eMMC [0000.128] W> DEVICE_PROD: device prod is not initialized. [0000.133] W> DEVICE_PROD: device prod is not initialized. [0000.150] I> sdmmc DDR50 mode [0000.153] W> DEVICE_PROD: device prod is not initialized. [0000.159] W> No valid slot number is found in scratch register [0000.164] W> Return default slot: _a [0000.168] I> Active Boot chain : 0 [0000.171] I> Boot-device: eMMC [0000.174] E> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.181] E> MB1_PLATFORM_CONFIG: Failed to initialize device prod. [0000.188] I> Temperature = 24500 [0000.191] W> Skipping boost for clk: BPMP_CPU_NIC [0000.195] W> Skipping boost for clk: BPMP_APB [0000.199] W> Skipping boost for clk: AXI_CBB [0000.203] W> Skipping boost for clk: AON_CPU_NIC [0000.208] W> Skipping boost for clk: CAN1 [0000.211] W> Skipping boost for clk: CAN2 [0000.216] I> Boot-device: eMMC [0000.218] I> Boot-device: eMMC [0000.228] I> Sdmmc: HS400 mode enabled [0000.232] I> ECC region[0]: Start:0x0, End:0x0 [0000.236] I> ECC region[1]: Start:0x0, End:0x0 [0000.241] I> ECC region[2]: Start:0x0, End:0x0 [0000.245] I> ECC region[3]: Start:0x0, End:0x0 [0000.249] I> ECC region[4]: Start:0x0, End:0x0 [0000.253] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.259] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.263] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.268] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.272] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.277] W> MB1_PLATFORM_CONFIG: Rail ID 9 not found in pmic rail config table. [0000.284] E> FAILED: Thermal config [0000.288] W> DEVICE_PROD: device prod is not initialized. [0000.297] W> MB1_PLATFORM_CONFIG: Rail ID 7 not found in pmic rail config table. [0000.304] E> FAILED: MEMIO rail config [0000.315] I> scrub mode: full dram [0000.319] E> FUSE: Failed to verify ECID. [0000.322] I> Boot-device: eMMC [0000.332] I> sdmmc bdev is already initialized [0000.372] W> No fuse-bypass data [0001.879] E> WP-1 ACK pending [0001.882] E> Error: 0 [0001.884] E> Task 71 failed (err: 0x32320006) [0001.888] E> Top caller module: CPUINIT, error module: CPUINIT, reason: 0x06, aux_info: 0x00 [0001.896] I> MB1(1.5.1.0-t194-41334769-59d8a47d) BIT boot status dump : 0000000000011111111110111111111111111111111001111111011100111111110110110000000000000000000000000000000000000000000000000000000011111011000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 [0001.926] I> Reset to recovery mode [0001.9