=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2019.11.29 16:34:57 =~=~=~=~=~=~=~=~=~=~=~= [0000.242] [TegraBoot] (version 00.00.2018.01-l4t-89b97a49) [0000.248] Processing in cold boot mode Bootloader 2 [0000.252] A02 Bootrom Patch rev = 1023 [0000.256] Power-up reason: pmc por [0000.259] No Battery Present [0000.262] pmic max77620 reset reason [0000.265] pmic max77620 NVERC : 0x50 [0000.268] RamCode = 0 [0000.271] Platform has DDR4 type RAM [0000.274] max77620 disabling SD1 Remote Sense [0000.278] Setting DDR voltage to 1125mv [0000.282] Serial Number of Pmic Max77663: 0x409ce [0000.290] Entering ramdump check [0000.293] Get RamDumpCarveOut = 0x0 [0000.296] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.301] Last reboot was clean, booting normally! [0000.306] Sdram initialization is successful [0000.310] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.316] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.322] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.328] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.333] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.339] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.345] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.351] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.367] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.373] Platform-DebugCarveout: 0 [0000.376] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.382] Non secure mode, and RB not enabled. [0000.399] Csd NumOfBlocks=0 [0000.407] Using GPT Primary to query partitions [0000.412] Loading Tboot-CPU binary [0000.418] Verifying TBC in OdmNonSecureSBK mode [0000.428] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.435] Bootloader downloaded successfully. [0000.439] Downloaded Tboot-CPU binary to 0xa0000258 [0000.444] MAX77620_GPIO5 configured [0000.448] CPU power rail is up [0000.450] CPU clock enabled [0000.454] Performing RAM repair [0000.457] Updating A64 Warmreset Address to 0xa00002e9 [0000.462] Loading NvTbootBootloaderDTB [0000.477] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.537] Bootloader DTB Load Address: 0x83000000 [0000.542] Loading NvTbootKernelDTB [0000.556] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.616] Kernel DTB Load Address: 0x83100000 [0000.621] Loading cboot binary [0000.637] Verifying EBT in OdmNonSecureSBK mode [0000.680] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.687] Bootloader downloaded successfully. [0000.693] Using BFS PT to query partitions [0000.697] Next binary entry address: 0x92c00258 [0000.702] BoardId: 3448 [0000.706] Overriding pmu board id with proc board id [0000.711] Display board id is not available [0000.727] Verifying SC7EntryFw in OdmNonSecureSBK mode [0000.777] /bpmp deleted [0000.780] SC7EntryFw header found loaded at 0xff700000 [0000.969] OVR2 PMIC [0000.970] Bpmp FW successfully loaded [0000.975] WB0 init successfully at 0xff780000 [0000.979] Set NvDecSticky Bits [0000.983] GSC2 address ff53fffc value c0edbbcc [0000.989] GSC MC Settings done [0000.992] TOS Image length 53680 [0000.995] Monitor size 53680 [0000.998] OS size 0 [0001.004] Secure Os AES-CMAC Verification Success! [0001.008] TOS image cipher info: plaintext [0001.012] Loading and Validation of Secure OS Successful [0001.028] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.033] NvTbootPackSdramParams: start. [0001.038] NvTbootPackSdramParams: done. [0001.042] Tegraboot started after 172649 us [0001.046] Basic modules init took 560456 us [0001.050] Sec Bootdevice Read Time = 57 ms, Read Size = 2292 KB [0001.055] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.061] Next stage binary read took 11930 us [0001.065] Carveout took -23630 us [0001.068] CPU initialization took 345528 us [0001.072] Total time taken by TegraBoot 894284 us [0001.077] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):a28d87f09 NOTICE: BL31: Built : 21:10:01, Aug 12 2019 ERROR: Error initializing runtime service trusty_fast [0001.199] RamCode = 0 [0001.204] LPDDR4 Training: Read DT: Number of tables = 2 [0001.209] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.221] EMC Training Successful [0001.224] 408000 not found in DVFS table [0001.231] RamCode = 0 [0001.234] DT Write: emc-table@204000 succeeded [0001.240] DT Write: emc-table@1600000 succeeded [0001.244] LPDDR4 Training: Write DT: Number of tables = 2 [0001.283] [0001.284] Debug Init done [0001.287] Marked DTB cacheable [0001.290] Bootloader DTB loaded at 0x83000000 [0001.294] Marked DTB cacheable [0001.297] Kernel DTB loaded at 0x83100000 [0001.301] DeviceTree Init done [0001.313] Pinmux applied successfully [0001.317] gicd_base: 0x50041000 [0001.320] gicc_base: 0x50042000 [0001.323] Interrupts Init done [0001.328] Using base:0x60005090 & irq:208 for tick-timer [0001.333] Using base:0x60005098 for delay-timer [0001.337] platform_init_timer: DONE [0001.341] Timer(tick) Init done [0001.344] osc freq = 38400 khz [0001.348] [0001.349] welcome to cboot [0001.352] [0001.353] Cboot Version: 00.00.2018.01-t210-3a168c35 [0001.358] calling constructors [0001.361] initializing heap [0001.364] initializing threads [0001.367] initializing timers [0001.370] creating bootstrap completion thread [0001.374] top of bootstrap2() [0001.377] CPU: ARM Cortex A57 [0001.380] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.384] initializing platform [0001.387] Scratch reg 37 & 271 initial value set.. [0001.394] cboot:secure-pmc present [0001.444] config for ddr50 mode completed [0001.447] sdmmc bdev is already initialized [0001.451] Enable APE clock [0001.454] Un-powergate APE partition [0001.458] of_register: registering tegra_udc to of_hal [0001.463] of_register: registering tegra_udc to of_hal [0001.468] of_register: registering inv20628-driver to of_hal [0001.473] of_register: registering ads1015-driver to of_hal [0001.479] of_register: registering lp8557-bl-driver to of_hal [0001.485] of_register: registering bq2419x_charger to of_hal [0001.490] of_register: registering cpc to of_hal [0001.495] of_register: registering bq27441_fuel_gauge to of_hal [0001.506] gpio framework initialized [0001.510] of_register: registering tca9539_gpio to of_hal [0001.515] of_register: registering tca9539_gpio to of_hal [0001.520] of_register: registering i2c_bus_driver to of_hal [0001.526] of_register: registering i2c_bus_driver to of_hal [0001.532] of_register: registering i2c_bus_driver to of_hal [0001.537] of_register: registering i2c_bus_driver to of_hal [0001.543] pmic framework initialized [0001.546] of_register: registering max77620_pmic to of_hal [0001.552] regulator framework initialized [0001.556] of_register: registering tps65132_bl_driver to of_hal [0001.562] initializing target [0001.567] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.576] fixed regulator driver initialized [0001.593] initializing OF layer [0001.596] NCK carveout not present [0001.599] Skipping dts_overrides [0001.603] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.619] I2C Bus Init done [0001.622] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.632] I2C Bus Init done [0001.634] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.645] I2C Bus Init done [0001.647] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.658] I2C Bus Init done [0001.660] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.670] I2C Bus Init done [0001.673] of_children_init: Ops found for compatible string maxim,max77620 [0001.683] max77620_init using irq 118 [0001.688] register 'maxim,max77620' pmic [0001.692] gpio_driver_register: register 'max77620-gpio' driver [0001.699] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.709] I2C Bus Init done [0001.713] NCK carveout not present [0001.716] shim_invoke: No NCT, Calling dts updates [0001.727] Find /i2c@7000c000's alias i2c0 [0001.731] get eeprom at 1-a0, size 256, type 0 [0001.740] Find /i2c@7000c500's alias i2c2 [0001.743] get eeprom at 3-a0, size 256, type 0 [0001.748] get eeprom at 3-ae, size 256, type 0 [0001.752] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.758] I2C slave not started [0001.761] I2C write failed [0001.763] Writing offset failed [0001.766] eeprom_init: EEPROM read failed [0001.770] pm_ids_update: eeprom init failed [0001.774] pm_ids_update: Updating 3,a0, size 256, type 0 [0001.804] pm_ids_update: The pm board id is 3448-0002-400 [0001.811] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0001.818] pm_ids_update: pm id update successful [0001.823] pm_ids_update: Updating 3,ae, size 256, type 0 [0001.828] I2C slave not started [0001.831] I2C write failed [0001.834] Writing offset failed [0001.837] eeprom_init: EEPROM read failed [0001.841] pm_ids_update: eeprom init failed [0001.871] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0001.877] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0001.885] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0001.891] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0001.899] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:c7:c7 [0001.905] Plugin Manager: Parse ODM data 0x00094000 [0001.915] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0001.936] Find /i2c@7000c000's alias i2c0 [0001.940] get eeprom at 1-a0, size 256, type 0 [0001.949] Find /i2c@7000c500's alias i2c2 [0001.953] get eeprom at 3-a0, size 256, type 0 [0001.957] get eeprom at 3-ae, size 256, type 0 [0001.961] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.967] I2C slave not started [0001.970] I2C write failed [0001.972] Writing offset failed [0001.975] eeprom_init: EEPROM read failed [0001.979] pm_ids_update: eeprom init failed [0001.983] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.013] pm_ids_update: The pm board id is 3448-0002-400 [0002.020] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0002.027] pm_ids_update: pm id update successful [0002.031] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.037] I2C slave not started [0002.040] I2C write failed [0002.042] Writing offset failed [0002.045] eeprom_init: EEPROM read failed [0002.049] pm_ids_update: eeprom init failed [0002.079] Chip UID is 000000016445c8451c00000006018380 [0002.084] Add serial number:14230191104550808301 as DT property [0002.092] Applying platform configs [0002.098] platform-init is not present. Skipping [0002.103] calling apps_init() [0002.119] Found 14 GPT partitions in "sdmmc3_user" [0002.123] Proceeding to Cold Boot [0002.127] starting app android_boot_app [0002.130] Device state: unlocked [0002.134] display console init [0002.142] could not find regulator [0002.145] hdmi cable connected [0002.161] edid read success [0002.176] edid read success [0002.178] wiDT entry for leds-pwm not found d[0002.185] th = 640, height = 480, frequency = 25174825 [0002.190] width = 640, height = 480, frequency = 25174825 [0002.196] width = 640, height = 480, frequency = 25174825 [0002.201] width = 640, height = 480, frequency = 25174825 [0002.207] width = 1920, height = 1080, frequency = 148500000 [0002.212] width = 1920, height = 1080, frequency = 148500000 [0002.218] width = 1920, height = 1080, frequency = 148351648 [0002.223] width = 1280, height = 720, frequency = 74175824 [0002.229] width = 720, height = 480, frequency = 26973026 [0002.234] width = 720, height = 480, frequency = 26973026 [0002.240] width = 1920, height = 1080, frequency = 148351648 [0002.245] width = 1280, height = 720, frequency = 74175824 [0002.251] width = 720, height = 576, frequency = 26973026 [0002.256] width = 720, height = 576, frequency = 26973026 [0002.262] width = 640, height = 480, frequency = 25174825 [0002.267] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.275] tmds-config node not found [0002.279] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.293] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.301] could not find regulator [0002.304] could not find regulator [0002.308] could not find regulator [0002.336] using default cmu settings [0002.340] dc_hdmi_enable, starting HDMI initialisation [0002.346] dc_hdmi_enable, HDMI initialisation complete [0002.351] list and configure display window [0002.360] display console init completed [0002.370] subnode volume_up is not found ! [0002.374] subnode back is not found ! [0002.378] subnode volume_down is not found ! [0002.382] subnode menu is not found ! [0002.386] Gpio keyboard init success [0002.432] found decompressor handler: lz4-legacy [0002.447] decompressing blob (type 1)... [0002.482] load_bmp_blob: panelresolution=1080 type=3 [0002.531] decompressor handler not found [0002.535] load_firmware_blob: Firmware blob loaded, entries=2 [0002.541] se_aes_verify_sbk_clear: Error [0002.545] bl_battery_charging: connected to external power supply [0002.552] xusb is supported [0002.558] error while finding nvidia,portmap [0002.563] could not find regulator [0003.066] xusb blob version 0 size 124416 [0003.070] firmware size 124416 [0003.075] Firmware timestamp: 0x5cd2a472, Version: 50.22 release [0003.090] xhci0: 64 bytes context size, 32-bit DMA [0003.130] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.150] uhub0: on usbus0 [0003.800] uhub0: 9 ports with 9 removable, self powered [0004.800] failed to get HID devices [0004.803] failed to init xhci or no usb device attached [0004.816] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0004.824] MSC Partition not found [0004.833] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [0004.841] USP partition read failed! [0004.844] blob_init: blob-partition USP header read failed [0004.850] android_boot Unable to update recovery partition [0004.855] kfs_getpartname: name = LNX [0004.859] Loading kernel from LNX [0004.884] Verifying boot image in OdmNonSecureSBK mode [0004.928] kernel load address: 0x80080000, size: 482032 bytes [0004.934] ramdisk load address: 0x84100000, size: 0 bytes [0004.939] load kernel from storage [0004.949] decompressor handler not found [0004.968] Successfully loaded kernel and ramdisk images [0004.974] load_bmp_blob: panelresolution=1080 type=3 [0005.471] display bmp image done [0005.475] NCK carveout not present [0005.478] Skipping dts_overrides [0005.481] NCK carveout not present [0005.484] shim_invoke: No NCT, Calling dts updates [0005.495] Find /i2c@7000c000's alias i2c0 [0005.499] get eeprom at 1-a0, size 256, type 0 [0005.508] Find /i2c@7000c500's alias i2c2 [0005.512] get eeprom at 3-a0, size 256, type 0 [0005.516] get eeprom at 3-ae, size 256, type 0 [0005.521] pm_ids_update: Updating 1,a0, size 256, type 0 [0005.526] I2C slave not started [0005.529] I2C write failed [0005.532] Writing offset failed [0005.535] eeprom_init: EEPROM read failed [0005.539] pm_ids_update: eeprom init failed [0005.543] pm_ids_update: Updating 3,a0, size 256, type 0 [0005.573] pm_ids_update: The pm board id is 3448-0002-400 [0005.579] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0005.587] pm_ids_update: pm id update successful [0005.592] pm_ids_update: Updating 3,ae, size 256, type 0 [0005.597] I2C slave not started [0005.600] I2C write failed [0005.603] Writing offset failed [0005.606] eeprom_init: EEPROM read failed [0005.610] pm_ids_update: eeprom init failed [0005.640] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.645] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0005.653] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.659] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0005.668] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:c7:c7 [0005.674] Plugin Manager: Parse ODM data 0x00094000 [0005.683] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.698] Add serial number:14230191104550808301 as DT property [0005.707] "bpmp" doesn't exist, creating [0005.713] Updated bpmp info to DTB [0005.717] Updated initrd info to DTB [0005.721] "proc-board" doesn't exist, creating [0005.726] Updated board info to DTB [0005.730] "pmu-board" doesn't exist, creating [0005.735] Updated board info to DTB [0005.738] "display-board" doesn't exist, creating [0005.744] Updated board info to DTB [0005.747] "reset" doesn't exist, creating [0005.752] Updated reset info to DTB [0005.755] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb3000 is_hdmi_initialised=1 [0005.794] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.806] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.819] Updated bootarg info to DTB [0005.823] Adding uuid 000000016445c8451c00000006018380 to DT [0005.829] Adding eks info 0 to DT [0005.834] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0005.840] Updated memory info to DTB [0005.848] set vdd_core voltage to 1075 mv [0005.852] setting 'vdd-core' regulator to 1075000 micro volts [0005.870] could not find regulator [0005.874] Found secure-pmc; disable BPMP U-Boot 2016.07-gd917e08cec (Aug 12 2019 - 21:10:20 -0700) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. MMC: no card present ** Bad device mmc 1 ** Hit any key to stop autoboot: 1  0 MMC: no card present switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 733 bytes read in 74 ms (8.8 KiB/s) L4T boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 5562384 bytes read in 184 ms (28.8 MiB/s) Retrieving file: /boot/Image 34310152 bytes read in 809 ms (40.4 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb3000 is_hdmi_initialised=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 0000000083173489 Starting kernel ... [ 1.085740] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.567239] cgroup: cgroup2: unknown option "nsdelegate" [ 1.655749] mmc1: Data CRC error [ 1.659008] sdhci: =========== REGISTER DUMP (mmc1)=========== [ 1.664873] sdhci: Sys addr: 0x00000008 | Version: 0x00000303 [ 1.670737] sdhci: Blk size: 0x00007200 | Blk cnt: 0x00000007 [ 1.676599] sdhci: Argument: 0x00000000 | Trn mode: 0x0000003b [ 1.682461] sdhci: Present: 0x01fb0008 | Host ctl: 0x00000017 [ 1.688321] sdhci: Power: 0x00000001 | Blk gap: 0x00000000 [ 1.694181] sdhci: Wake-up: 0x00000000 | Clock: 0x00000007 [ 1.700042] sdhci: Timeout: 0x0000000e | Int stat: 0x00001000 [ 1.705903] sdhci: Int enab: 0x02ff100b | Sig enab: 0x02fc100b [ 1.711764] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 [ 1.717626] sdhci: Caps: 0x376cd08c | Caps_1: 0x10006f77 [ 1.723485] sdhci: Cmd: 0x0000123a | Max curr: 0x00000000 [ 1.729343] sdhci: Host ctl2: 0x0000308b [ 1.733289] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000ffefe410 [ 1.739903] sdhci: =========================================== [ 7.798988] tegra-xusb 70090000.xusb: HC died; cleaning up [ 12.150873] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 12.157897] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 12.164646] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 12.169832] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 12.176753] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 12.182364] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 12.188241] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 12.193503] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 12.198950] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 13.686853] mmc0: Timeout waiting for hardware interrupt. [ 13.692289] sdhci: =========== REGISTER DUMP (mmc0)=========== [ 13.698159] sdhci: Sys addr: 0x00000008 | Version: 0x00000303 [ 13.704025] sdhci: Blk size: 0x00007200 | Blk cnt: 0x00000000 [ 13.709893] sdhci: Argument: 0x00c15f48 | Trn mode: 0x0000003b [ 13.715759] sdhci: Present: 0x01fb00f0 | Host ctl: 0x00000035 [ 13.721626] sdhci: Power: 0x00000001 | Blk gap: 0x00000000 [ 13.727496] sdhci: Wake-up: 0x00000000 | Clock: 0x00000007 [ 13.733364] sdhci: Timeout: 0x0000000e | Int stat: 0x00000002 [ 13.739229] sdhci: Int enab: 0x02ff100b | Sig enab: 0x02fc100b [ 13.745099] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 [ 13.750966] sdhci: Caps: 0x376cd08c | Caps_1: 0x10006f77 [ 13.756834] sdhci: Cmd: 0x0000123a | Max curr: 0x00000000 [ 13.762699] sdhci: Host ctl2: 0x0000300d [ 13.766654] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000ffefe410 [ 13.773274] sdhci: =========================================== [ 22.390867] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 22.397888] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 22.404643] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 22.409823] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 22.416746] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 22.422371] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 22.428244] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 22.433507] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 22.438957] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 22.445516] Failed to set dvfs regulator vdd-core [ 22.658833] INFO: rcu_sched detected stalls on CPUs/tasks: [ 22.664381] 0-...: (0 ticks this GP) idle=c7d/2/0 softirq=297/297 fqs=2396 [ 22.671465] (detected by 3, t=5252 jiffies, g=-281, c=-282, q=11) [ 22.677760] INFO: rcu_preempt detected stalls on CPUs/tasks: [ 22.683471] 0-...: (1 GPs behind) idle=c7d/2/0 softirq=296/297 fqs=2303 [ 22.690292] (detected by 3, t=5255 jiffies, g=-156, c=-157, q=533) [ 32.630859] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 32.639383] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 32.647652] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 32.654372] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 32.662864] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 32.670061] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 32.677508] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 32.684328] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 32.691307] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 42.874858] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 42.883396] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 42.891670] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 42.898381] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 42.906834] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 42.913983] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 42.921392] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 42.928195] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 42.935168] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 42.943250] Failed to set dvfs regulator vdd-core [ 53.114857] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 53.123428] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 53.131742] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 53.138482] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 53.146960] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 53.154116] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 53.161519] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 53.168294] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 53.175235] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 63.354868] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 63.363380] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 63.371634] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 63.378324] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 63.386769] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 63.393911] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 63.401308] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 63.408078] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 63.415008] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 63.423044] Failed to set dvfs regulator vdd-core [ 63.429281] Failed to set regulator vdd-core for clock cbus to 800 mV [ 73.594857] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 73.603393] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 73.611662] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 73.618374] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 73.626844] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 73.634002] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 73.641416] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 73.648215] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 73.655179] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 83.830867] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 83.839403] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 83.847657] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 83.854333] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 83.862750] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 83.869860] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 83.877228] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 83.883972] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 83.890895] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 83.898932] Failed to set dvfs regulator vdd-core [ 85.678852] INFO: rcu_sched detected stalls on CPUs/tasks: [ 85.685907] 0-...: (0 ticks this GP) idle=c7d/2/0 softirq=297/297 fqs=9865 [ 85.694503] [ 85.694741] INFO: rcu_preempt detected stalls on CPUs/tasks: [ 85.694747] 0-...: (1 GPs behind) idle=c7d/2/0 softirq=296/297 fqs=9397 [ 85.694748] [ 94.074862] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 94.083400] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 94.091667] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 94.098355] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 94.106759] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 94.113861] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 94.121220] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 94.127955] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 94.134865] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 104.314863] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 104.323360] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 104.331603] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 104.338276] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 104.346691] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 104.353791] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 104.361146] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 104.367876] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 104.374779] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 104.382818] Failed to set dvfs regulator vdd-core [ 114.554853] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 114.563384] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 114.571653] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 114.578337] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 114.586750] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 114.593854] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 114.601210] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 114.607948] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 114.614856] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 124.790865] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 124.799361] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 124.807601] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 124.814273] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 124.822683] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 124.829784] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 124.837138] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 124.843873] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 124.850781] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 124.858823] Failed to set dvfs regulator vdd-core [ 124.865047] Failed to set regulator vdd-core for clock vi to 800 mV [ 135.030870] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 135.039397] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 135.047653] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 135.054340] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 135.062757] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 135.069859] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 135.077213] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 135.083948] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 135.090858] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 145.270868] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 145.279365] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 145.287603] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 145.294274] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 145.302681] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 145.309782] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 145.317137] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 145.323876] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 145.330781] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 145.338809] Failed to set dvfs regulator vdd-core [ 148.698840] INFO: rcu_sched detected stalls on CPUs/tasks: [ 148.705885] 0-...: (0 ticks this GP) idle=c7d/2/0 softirq=297/297 fqs=16843 [ 148.714569] (detected by 3, t=36762 jiffies, g=-281, c=-282, q=11) [ 148.722451] INFO: rcu_preempt detected stalls on CPUs/tasks: [ 148.729682] 0-...: (1 GPs behind) idle=c7d/2/0 softirq=296/297 fqs=16968 [ 148.738109] (detected by 3, t=36766 jiffies, g=-156, c=-157, q=533) [ 155.510872] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 155.519406] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 155.527666] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 155.534342] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 155.542768] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 155.549882] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 155.557248] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 155.563996] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 155.570925] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 165.754871] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 165.763379] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 165.771631] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 165.778308] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 165.786730] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 165.793846] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 165.801206] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 165.807958] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 165.814884] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 165.822925] Failed to set dvfs regulator vdd-core [ 175.990864] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 175.999404] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 176.007670] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 176.014355] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 176.022783] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 176.029900] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 176.037273] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 176.044019] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 176.050950] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 186.234870] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 186.243388] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 186.251643] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 186.258327] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 186.266751] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 186.273868] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 186.281236] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 186.287990] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 186.294918] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 186.302967] Failed to set dvfs regulator vdd-core [ 186.309218] Failed to set regulator vdd-core for clock cbus to 800 mV [ 196.474858] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 196.483384] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 196.491650] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 196.498326] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 196.506747] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 196.513862] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 196.521237] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 196.527991] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 196.534918] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 206.710862] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 206.719375] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 206.727626] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 206.734315] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 206.742749] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 206.749867] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 206.757243] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 206.763999] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 206.770932] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 206.778978] Failed to set dvfs regulator vdd-core [ 211.718854] INFO: rcu_sched detected stalls on CPUs/tasks: [ 211.725908] 0-...: (0 ticks this GP) idle=c7d/2/0 softirq=297/297 fqs=23876 [ 211.734602] (detected by 3, t=52517 jiffies, g=-281, c=-282, q=11) [ 211.742490] INFO: rcu_preempt detected stalls on CPUs/tasks: [ 211.749723] 0-...: (1 GPs behind) idle=c7d/2/0 softirq=296/297 fqs=24413 [ 211.758149] (detected by 3, t=52521 jiffies, g=-156, c=-157, q=533) [ 216.950867] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 216.959410] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 216.967679] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 216.974361] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 216.982784] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 216.989900] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 216.997270] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 217.004023] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 217.010958] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 227.190866] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 227.199380] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 227.207640] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 227.214321] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 227.222753] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 227.229870] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 227.237244] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 227.243999] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 227.250926] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 227.258973] Failed to set dvfs regulator vdd-core [ 237.434862] tegra-i2c 7000d000.i2c: pio timed out addr: 0x3c tlen:28 rlen:4 [ 237.443405] tegra-i2c 7000d000.i2c: --- register dump for debugging ---- [ 237.451675] tegra-i2c 7000d000.i2c: I2C_CNFG - 0x22c00 [ 237.458358] tegra-i2c 7000d000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x1010001 [ 237.466783] tegra-i2c 7000d000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 237.473899] tegra-i2c 7000d000.i2c: I2C_FIFO_STATUS - 0x800081 [ 237.481272] tegra-i2c 7000d000.i2c: I2C_INT_MASK - 0x7d [ 237.488025] tegra-i2c 7000d000.i2c: I2C_INT_STATUS - 0xc3 [ 237.494954] tegra-i2c 7000d000.i2c: i2c transfer timed out addr: 0x3c [ 242.810874] INFO: task kworker/3:1:637 blocked for more than 120 seconds. [ 242.819231] Tainted: G W 4.9.140-tegra #1 [ 242.826463] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 242.836021] Kernel panic - not syncing: hung_task: blocked tasks [ 242.843627] CPU: 2 PID: 589 Comm: khungtaskd Tainted: G W 4.9.140-tegra #1 [ 242.853244] Hardware name: NVIDIA Jetson Nano Developer Kit (DT) [ 242.860870] Call trace: [ 242.864934] [] dump_backtrace+0x0/0x198 [ 242.871972] [] show_stack+0x24/0x30 [ 242.878663] [] dump_stack+0x98/0xc0 [ 242.885358] [] panic+0x11c/0x298 [ 242.891790] [] watchdog+0x300/0x3b8 [ 242.898465] [] kthread+0xec/0xf0 [ 242.904872] [] ret_from_fork+0x10/0x40 [ 242.911785] SMP: stopping secondary CPUs [ 242.917404] Kernel Offset: disabled [ 242.922476] Memory Limit: none [ 242.935020] Rebooting in 5 seconds.. [0000.206] [TegraBoot] (version 00.00.2018.01-l4t-89b97a49) [0000.211] Processing in cold boot mode Bootloader 2 [0000.216] A02 Bootrom Patch rev = 1023 [0000.219] Power-up reason: software reset [0000.223] No Battery Present [0000.226] pmic max77620 reset reason [0000.229] pmic max77620 NVERC : 0x0 [0000.232] RamCode = 0 [0000.235] Platform has DDR4 type RAM [0000.238] max77620 disabling SD1 Remote Sense [0000.242] Setting DDR voltage to 1125mv [0000.246] Serial Number of Pmic Max77663: 0x409ce [0000.254] Entering ramdump check [0000.257] Get RamDumpCarveOut = 0x0 [0000.260] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.265] Last reboot was clean, booting normally! [0000.270] Sdram initialization is successful [0000.274] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.280] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.286] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.292] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.297] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.303] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.309] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.315] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.331] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.337] Platform-DebugCarveout: 0 [0000.340] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.346] Non secure mode, and RB not enabled. [0000.363] Csd NumOfBlocks=0 [0000.372] Using GPT Primary to query partitions [0000.376] Loading Tboot-CPU binary [0000.382] Verifying TBC in OdmNonSecureSBK mode [0000.392] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.399] Bootloader downloaded successfully. [0000.403] Downloaded Tboot-CPU binary to 0xa0000258 [0000.408] MAX77620_GPIO5 configured [0000.412] CPU power rail is up [0000.414] CPU clock enabled [0000.418] Performing RAM repair [0000.421] Updating A64 Warmreset Address to 0xa00002e9 [0000.426] Loading NvTbootBootloaderDTB [0000.440] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.501] Bootloader DTB Load Address: 0x83000000 [0000.506] Loading NvTbootKernelDTB [0000.520] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.580] Kernel DTB Load Address: 0x83100000 [0000.585] Loading cboot binary [0000.601] Verifying EBT in OdmNonSecureSBK mode [0000.643] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.650] Bootloader downloaded successfully. [0000.657] Using BFS PT to query partitions [0000.661] Next binary entry address: 0x92c00258 [0000.666] BoardId: 3448 [0000.670] Overriding pmu board id with proc board id [0000.675] Display board id is not available [0000.691] Verifying SC7EntryFw in OdmNonSecureSBK mode [0000.741] /bpmp deleted [0000.743] SC7EntryFw header found loaded at 0xff700000 [0000.933] OVR2 PMIC [0000.934] Bpmp FW successfully loaded [0000.939] WB0 init successfully at 0xff780000 [0000.943] Set NvDecSticky Bits [0000.947] GSC2 address ff53fffc value c0edbbcc [0000.953] GSC MC Settings done [0000.956] TOS Image length 53680 [0000.959] Monitor size 53680 [0000.962] OS size 0 [0000.968] Secure Os AES-CMAC Verification Success! [0000.972] TOS image cipher info: plaintext [0000.976] Loading and Validation of Secure OS Successful [0000.992] SC7 Entry Firmware - 0xff700000, 0x4000 [0000.997] NvTbootPackSdramParams: start. [0001.002] NvTbootPackSdramParams: done. [0001.005] Tegraboot started after 135264 us [0001.009] Basic modules init took 560877 us [0001.013] Sec Bootdevice Read Time = 57 ms, Read Size = 2292 KB [0001.019] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.025] Next stage binary read took 11929 us [0001.029] Carveout took -23628 us [0001.032] CPU initialization took 345501 us [0001.036] Total time taken by TegraBoot 894679 us [0001.041] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):a28d87f09 NOTICE: BL31: Built : 21:10:01, Aug 12 2019 ERROR: Error initializing runtime service trusty_fast [0001.163] RamCode = 0 [0001.168] LPDDR4 Training: Read DT: Number of tables = 2 [0001.173] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.185] EMC Training Successful [0001.188] 408000 not found in DVFS table [0001.195] RamCode = 0 [0001.198] DT Write: emc-table@204000 succeeded [0001.204] DT Write: emc-table@1600000 succeeded [0001.208] LPDDR4 Training: Write DT: Number of tables = 2 [0001.246] [0001.247] Debug Init done [0001.250] Marked DTB cacheable [0001.253] Bootloader DTB loaded at 0x83000000 [0001.257] Marked DTB cacheable [0001.260] Kernel DTB loaded at 0x83100000 [0001.264] DeviceTree Init done [0001.276] Pinmux applied successfully [0001.280] gicd_base: 0x50041000 [0001.283] gicc_base: 0x50042000 [0001.286] Interrupts Init done [0001.291] Using base:0x60005090 & irq:208 for tick-timer [0001.296] Using base:0x60005098 for delay-timer [0001.300] platform_init_timer: DONE [0001.304] Timer(tick) Init done [0001.307] osc freq = 38400 khz [0001.311] [0001.312] welcome to cboot [0001.315] [0001.316] Cboot Version: 00.00.2018.01-t210-3a168c35 [0001.321] calling constructors [0001.324] initializing heap [0001.327] initializing threads [0001.330] initializing timers [0001.333] creating bootstrap completion thread [0001.337] top of bootstrap2() [0001.340] CPU: ARM Cortex A57 [0001.343] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.347] initializing platform [0001.350] Scratch reg 37 & 271 initial value set.. [0001.357] cboot:secure-pmc present [0001.406] config for ddr50 mode completed [0001.410] sdmmc bdev is already initialized [0001.414] Enable APE clock [0001.417] Un-powergate APE partition [0001.421] of_register: registering tegra_udc to of_hal [0001.426] of_register: registering tegra_udc to of_hal [0001.431] of_register: registering inv20628-driver to of_hal [0001.436] of_register: registering ads1015-driver to of_hal [0001.442] of_register: registering lp8557-bl-driver to of_hal [0001.448] of_register: registering bq2419x_charger to of_hal [0001.453] of_register: registering cpc to of_hal [0001.458] of_register: registering bq27441_fuel_gauge to of_hal [0001.469] gpio framework initialized [0001.473] of_register: registering tca9539_gpio to of_hal [0001.478] of_register: registering tca9539_gpio to of_hal [0001.483] of_register: registering i2c_bus_driver to of_hal [0001.489] of_register: registering i2c_bus_driver to of_hal [0001.495] of_register: registering i2c_bus_driver to of_hal [0001.500] of_register: registering i2c_bus_driver to of_hal [0001.506] pmic framework initialized [0001.509] of_register: registering max77620_pmic to of_hal [0001.515] regulator framework initialized [0001.519] of_register: registering tps65132_bl_driver to of_hal [0001.524] initializing target [0001.530] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.539] fixed regulator driver initialized [0001.556] initializing OF layer [0001.559] NCK carveout not present [0001.562] Skipping dts_overrides [0001.566] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.582] I2C Bus Init done [0001.584] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.595] I2C Bus Init done [0001.597] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.608] I2C Bus Init done [0001.610] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.620] I2C Bus Init done [0001.623] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.633] I2C Bus Init done [0001.636] of_children_init: Ops found for compatible string maxim,max77620 [0001.646] max77620_init using irq 118 [0001.651] register 'maxim,max77620' pmic [0001.655] gpio_driver_register: register 'max77620-gpio' driver [0001.662] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.672] I2C Bus Init done [0001.675] NCK carveout not present [0001.679] shim_invoke: No NCT, Calling dts updates [0001.690] Find /i2c@7000c000's alias i2c0 [0001.694] get eeprom at 1-a0, size 256, type 0 [0001.702] Find /i2c@7000c500's alias i2c2 [0001.706] get eeprom at 3-a0, size 256, type 0 [0001.711] get eeprom at 3-ae, size 256, type 0 [0001.715] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.720] I2C slave not started [0001.723] I2C write failed [0001.726] Writing offset failed [0001.729] eeprom_init: EEPROM read failed [0001.733] pm_ids_update: eeprom init failed [0001.737] pm_ids_update: Updating 3,a0, size 256, type 0 [0001.767] pm_ids_update: The pm board id is 3448-0002-400 [0001.774] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0001.781] pm_ids_update: pm id update successful [0001.786] pm_ids_update: Updating 3,ae, size 256, type 0 [0001.791] I2C slave not started [0001.794] I2C write failed [0001.797] Writing offset failed [0001.800] eeprom_init: EEPROM read failed [0001.804] pm_ids_update: eeprom init failed [0001.834] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0001.840] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0001.848] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0001.854] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0001.862] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:c7:c7 [0001.868] Plugin Manager: Parse ODM data 0x00094000 [0001.878] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0001.899] Find /i2c@7000c000's alias i2c0 [0001.903] get eeprom at 1-a0, size 256, type 0 [0001.912] Find /i2c@7000c500's alias i2c2 [0001.915] get eeprom at 3-a0, size 256, type 0 [0001.920] get eeprom at 3-ae, size 256, type 0 [0001.924] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.930] I2C slave not started [0001.933] I2C write failed [0001.935] Writing offset failed [0001.938] eeprom_init: EEPROM read failed [0001.942] pm_ids_update: eeprom init failed [0001.946] pm_ids_update: Updating 3,a0, size 256, type 0 [0001.976] pm_ids_update: The pm board id is 3448-0002-400 [0001.983] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0001.990] pm_ids_update: pm id update successful [0001.994] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.000] I2C slave not started [0002.003] I2C write failed [0002.005] Writing offset failed [0002.008] eeprom_init: EEPROM read failed [0002.012] pm_ids_update: eeprom init failed [0002.042] Chip UID is 000000016445c8451c00000006018380 [0002.047] Add serial number:14230191104550808301 as DT property [0002.055] Applying platform configs [0002.061] platform-init is not present. Skipping [0002.066] calling apps_init() [0002.082] Found 14 GPT partitions in "sdmmc3_user" [0002.086] Proceeding to Cold Boot [0002.090] starting app android_boot_app [0002.093] Device state: unlocked [0002.096] display console init [0002.105] could not find regulator [0002.108] hdmi cable connected [0002.124] edid read success [0002.139] edid read success [0002.141] widDT entry for leds-pwm not found t[0002.148] h = 640, height = 480, frequency = 25174825 [0002.153] width = 640, height = 480, frequency = 25174825 [0002.159] width = 640, height = 480, frequency = 25174825 [0002.164] width = 640, height = 480, frequency = 25174825 [0002.169] width = 1920, height = 1080, frequency = 148500000 [0002.175] width = 1920, height = 1080, frequency = 148500000 [0002.181] width = 1920, height = 1080, frequency = 148351648 [0002.186] width = 1280, height = 720, frequency = 74175824 [0002.192] width = 720, height = 480, frequency = 26973026 [0002.197] width = 720, height = 480, frequency = 26973026 [0002.203] width = 1920, height = 1080, frequency = 148351648 [0002.208] width = 1280, height = 720, frequency = 74175824 [0002.214] width = 720, height = 576, frequency = 26973026 [0002.219] width = 720, height = 576, frequency = 26973026 [0002.224] width = 640, height = 480, frequency = 25174825 [0002.230] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.238] tmds-config node not found [0002.242] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.256] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.264] could not find regulator [0002.267] could not find regulator [0002.271] could not find regulator [0002.299] using default cmu settings [0002.302] dc_hdmi_enable, starting HDMI initialisation [0002.309] dc_hdmi_enable, HDMI initialisation complete [0002.314] list and configure display window [0002.322] display console init completed [0002.333] subnode volume_up is not found ! [0002.337] subnode back is not found ! [0002.341] subnode volume_down is not found ! [0002.345] subnode menu is not found ! [0002.349] Gpio keyboard init success [0002.395] found decompressor handler: lz4-legacy [0002.410] decompressing blob (type 1)... [0002.445] load_bmp_blob: panelresolution=1080 type=3 [0002.494] decompressor handler not found [0002.498] load_firmware_blob: Firmware blob loaded, entries=2 [0002.504] se_aes_verify_sbk_clear: Error [0002.507] bl_battery_charging: connected to external power supply [0002.515] xusb is supported [0002.521] error while finding nvidia,portmap [0002.526] could not find regulator [0003.029] xusb blob version 0 size 124416 [0003.033] firmware size 124416 [0003.038] Firmware timestamp: 0x5cd2a472, Version: 50.22 release [0003.053] xhci0: 64 bytes context size, 32-bit DMA [0003.093] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.113] uhub0: on usbus0 [0003.763] uhub0: 9 ports with 9 removable, self powered [0004.763] failed to get HID devices [0004.766] failed to init xhci or no usb device attached [0004.779] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0004.787] MSC Partition not found [0004.796] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [0004.804] USP partition read failed! [0004.807] blob_init: blob-partition USP header read failed [0004.813] android_boot Unable to update recovery partition [0004.818] kfs_getpartname: name = LNX [0004.822] Loading kernel from LNX [0004.847] Verifying boot image in OdmNonSecureSBK mode [0004.891] kernel load address: 0x80080000, size: 482032 bytes [0004.896] ramdisk load address: 0x84100000, size: 0 bytes [0004.902] load kernel from storage [0004.912] decompressor handler not found [0004.931] Successfully loaded kernel and ramdisk images [0004.937] load_bmp_blob: panelresolution=1080 type=3 [0005.435] display bmp image done [0005.438] NCK carveout not present [0005.441] Skipping dts_overrides [0005.444] NCK carveout not present [0005.447] shim_invoke: No NCT, Calling dts updates [0005.459] Find /i2c@7000c000's alias i2c0 [0005.462] get eeprom at 1-a0, size 256, type 0 [0005.471] Find /i2c@7000c500's alias i2c2 [0005.475] get eeprom at 3-a0, size 256, type 0 [0005.480] get eeprom at 3-ae, size 256, type 0 [0005.484] pm_ids_update: Updating 1,a0, size 256, type 0 [0005.489] I2C slave not started [0005.492] I2C write failed [0005.495] Writing offset failed [0005.498] eeprom_init: EEPROM read failed [0005.502] pm_ids_update: eeprom init failed [0005.506] pm_ids_update: Updating 3,a0, size 256, type 0 [0005.536] pm_ids_update: The pm board id is 3448-0002-400 [0005.543] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0005.550] pm_ids_update: pm id update successful [0005.555] pm_ids_update: Updating 3,ae, size 256, type 0 [0005.560] I2C slave not started [0005.563] I2C write failed [0005.566] Writing offset failed [0005.569] eeprom_init: EEPROM read failed [0005.573] pm_ids_update: eeprom init failed [0005.603] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.609] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0005.617] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.622] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0005.631] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:c7:c7 [0005.637] Plugin Manager: Parse ODM data 0x00094000 [0005.647] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.661] Add serial number:14230191104550808301 as DT property [0005.671] "bpmp" doesn't exist, creating [0005.676] Updated bpmp info to DTB [0005.681] Updated initrd info to DTB [0005.684] "proc-board" doesn't exist, creating [0005.689] Updated board info to DTB [0005.693] "pmu-board" doesn't exist, creating [0005.698] Updated board info to DTB [0005.701] "display-board" doesn't exist, creating [0005.707] Updated board info to DTB [0005.710] "reset" doesn't exist, creating [0005.715] Updated reset info to DTB [0005.718] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb3000 is_hdmi_initialised=1 [0005.757] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.770] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.783] Updated bootarg info to DTB [0005.786] Adding uuid 000000016445c8451c00000006018380 to DT [0005.792] Adding eks info 0 to DT [0005.797] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0005.803] Updated memory info to DTB [0005.811] set vdd_core voltage to 1075 mv [0005.815] setting 'vdd-core' regulator to 1075000 micro volts [0005.833] could not find regulator [0005.836] Found secure-pmc; disable BPMP U-Boot 2016.07-gd917e08cec (Aug 12 2019 - 21:10:20 -0700) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. MMC: no card present ** Bad device mmc 1 ** Hit any key to stop autoboot: 1  0 MMC: no card present switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 733 bytes read in 74 ms (8.8 KiB/s) L4T boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 5562384 bytes read in 184 ms (28.8 MiB/s) Retrieving file: /boot/Image 34310152 bytes read in 809 ms (40.4 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb3000 is_hdmi_initialised=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 0000000083173489 Starting kernel ... [ 1.088546] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.538070] cgroup: cgroup2: unknown option "nsdelegate" [ 2.868951] using random self ethernet address [ 2.873697] using random host ethernet address [ 2.941820] using random self ethernet address [ 2.962035] using random host ethernet address [ 3.420213] random: crng init done [ 3.423649] random: 7 urandom warning(s) missed due to ratelimiting [ 3.751664] spidev: module is already loaded Ubuntu 18.04.2 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: nvidia (automatic login) Last login: Fri Nov 29 07:05:14 UTC 2019 on ttyS0 Welcome to Ubuntu 18.04.2 LTS (GNU/Linux 4.9.140-tegra aarch64) * Documentation: https://help.ubuntu.com * Management: https://landscape.canonical.com * Support: https://ubuntu.com/advantage This system has been minimized by removing packages and content that are not required on a system that users do not log into. To restore this content, you can run the 'unminimize' command. 0 packages can be updated. 0 updates are security updates. ]0;nvidia@tegra-ubuntu: ~nvidia@tegra-ubuntu:~$