[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (thangnt18@thangnt18-Vostro-7580) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #5 SMP PREEMPT Fri Jul 16 11:57:33 +07 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00140000@92cb4000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] On node 0 totalpages: 1039872 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 519168 pages, LIFO batch:31 [ 0.000000] Normal zone: 8136 pages used for memmap [ 0.000000] Normal zone: 520704 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] pcpu-alloc: s57560 r8192 d32552 u98304 alloc=24*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92cb4000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:2 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:2 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29180(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3567204K/4159488K available (15294K kernel code, 2948K rwdata, 6744K rodata, 8576K init, 611K bss, 117148K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009610000 ( 6784 KB) [ 0.000000] .init : 0xffffff8009610000 - 0xffffff8009e70000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e70000 - 0xffffff800a151008 ( 2949 KB) [ 0.000000] .bss : 0xffffff800a151008 - 0xffffff800a1e9cbc ( 612 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.001751] Console: colour dummy device 80x25 [ 0.001765] console [tty0] enabled [ 0.001771] bootconsole [uart8250] disabled [ 0.001789] kmemleak: Kernel memory leak detector disabled [ 0.001808] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.001820] pid_max: default: 32768 minimum: 301 [ 0.002271] Security Framework initialized [ 0.002487] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.002496] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003610] ftrace: allocating 47249 entries in 185 pages [ 0.172755] sched-energy: CPU device node has no sched-energy-costs [ 0.172790] ASID allocator initialised with 65536 entries [ 0.212179] tegra-id: chipid=22117. [ 0.212191] tegra-id: opt_subrevision=0. [ 0.212209] Tegra Speedo/IDDQ fuse revision 4 [ 0.212248] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.212253] Tegra: CPU Process ID 0, SoC Process ID 0, GPU Process ID 0 [ 0.212259] Tegra: CPU Speedo Value 2029, SoC Speedo Value 1902, GPU Speedo Value 2024 [ 0.212263] Tegra: CPU IDDQ Value 1852, SoC IDDQ Value 2032, GPU IDDQ Value 2420 [ 0.212283] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 0 [ 0.212300] DTS File Name: /home/thangnt18/Projects/source_accesscontrol/accesscontrol/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0002-p3449-0000-b00.dts [ 0.212309] DTB Build time: Jul 16 2021 11:57:53 [ 0.261075] CPU1: Booted secondary processor [411fd071] [ 0.292982] CPU2: Booted secondary processor [411fd071] [ 0.324963] CPU3: Booted secondary processor [411fd071] [ 0.325064] Brought up 4 CPUs [ 0.325072] SMP: Total of 4 processors activated. [ 0.325081] CPU features: detected feature: 32-bit EL0 Support [ 0.325345] CPU: All CPU(s) started at EL2 [ 0.325363] alternatives: patching kernel code [ 0.333553] devtmpfs: initialized [ 0.372510] Initilizing CustomIPI irq domain [ 0.372904] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.372925] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.383588] pinctrl core: initialized pinctrl subsystem [ 0.384187] OS set in device tree is not L4T. [ 0.384586] regulator-dummy: no parameters [ 0.384854] Initializing plugin-manager [ 0.385017] Plugin module not found [ 0.385249] node /plugin-manager/fragement@0 match with board >=3448-0002-100 [ 0.385763] node /plugin-manager/fragment@1 match with board >=3448-0002-101 [ 0.386204] node /plugin-manager/fragment@3 match with board >=3448-0002-100 [ 0.386915] node /plugin-manager/fragement@7 match with odm-data enable-pmic-wdt [ 0.387117] node /plugin-manager/fragement@8 match with odm-data enable-pmic-wdt [ 0.387693] node /plugin-manager/fragement@10 match with board >=3448-0002-300 [ 0.389678] node /plugin-manager/fragement@13 match with board >=3448-0002-300 [ 0.393287] NET: Registered protocol family 16 [ 0.394734] pstore: using zlib compression [ 0.394778] console [pstore-1] enabled [ 0.394783] pstore: Registered ramoops as persistent store backend [ 0.394789] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.394970] export_gpio194: invalid GPIO 194 [ 0.409092] cpuidle: using governor menu [ 0.413393] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.415179] vdso: 2 pages (1 code @ ffffff8008f77000, 1 data @ ffffff8009e74000) [ 0.415200] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.417589] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.419997] Serial: AMBA PL011 UART driver [ 0.420517] tegra_powergate_init: DONE [ 0.420531] DTS File Name: /home/thangnt18/Projects/source_accesscontrol/accesscontrol/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0002-p3449-0000-b00.dts [ 0.420537] DTB Build time: Jul 16 2021 11:57:53 [ 0.422570] Tegra reboot handler registered. [ 0.427135] iommu: Adding device tegra-carveouts to group 0 [ 0.427280] platform tegra-carveouts: domain=ffffffc0f9435498 allocates as[0]=ffffffc0f94300a8 [ 0.427627] iommu: Adding device smmu_test to group 1 [ 0.427669] platform smmu_test: domain=ffffffc0f94356d8 allocates as[0]=ffffffc0f9430110 [ 0.428472] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.428530] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.428585] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.428594] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.428617] mc-err: mcerr ops are set to t21x [ 0.439293] iommu: Adding device 70090000.xusb to group 2 [ 0.439570] iommu: Adding device 70006000.serial to group 3 [ 0.439643] platform 70006000.serial: domain=ffffffc0f94d1618 allocates as[0]=ffffffc0f9430178 [ 0.440067] iommu: Adding device 70006040.serial to group 4 [ 0.440278] iommu: Adding device sound to group 5 [ 0.440354] platform sound: domain=ffffffc0f94d19d8 allocates as[0]=ffffffc0f94301e0 [ 0.440921] iommu: Adding device 7000d400.spi to group 6 [ 0.441292] iommu: Adding device 50000000.host1x to group 7 [ 0.441583] iommu: Adding device 54080000.vi to group 8 [ 0.441981] iommu: Adding device 54600000.isp to group 9 [ 0.442249] iommu: Adding device 54680000.isp to group 10 [ 0.442529] iommu: Adding device tegradc.0 to group 11 [ 0.442585] platform tegradc.0: domain=ffffffc0f94de618 allocates as[0]=ffffffc0f9430248 [ 0.443973] platform tegradc.0: IOVA linear map 0x0000000092cb4000(140000) [ 0.444360] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.444692] iommu: Adding device tegradc.1 to group 12 [ 0.444759] platform tegradc.1: domain=ffffffc0f94de858 allocates as[0]=ffffffc0f94302b0 [ 0.446291] platform tegradc.1: IOVA linear map 0x0000000092cb4000(140000) [ 0.446680] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.446941] iommu: Adding device 54340000.vic to group 13 [ 0.447140] iommu: Adding device 544c0000.nvenc to group 14 [ 0.447333] iommu: Adding device 54500000.tsec to group 15 [ 0.447517] iommu: Adding device 54100000.tsecb to group 16 [ 0.447717] iommu: Adding device 54480000.nvdec to group 17 [ 0.447909] iommu: Adding device 54380000.nvjpg to group 18 [ 0.448971] iommu: Adding device 546c0000.i2c to group 19 [ 0.449343] iommu: Adding device 57000000.gpu to group 20 [ 0.449423] platform 57000000.gpu: domain=ffffffc0f94ea858 allocates as[0]=ffffffc0f9430318 [ 0.449456] platform 57000000.gpu: domain=ffffffc0f94ea858 allocates as[1]=ffffffc0f9430380 [ 0.449491] platform 57000000.gpu: domain=ffffffc0f94ea858 allocates as[2]=ffffffc0f94303e8 [ 0.449522] platform 57000000.gpu: domain=ffffffc0f94ea858 allocates as[3]=ffffffc0f9430450 [ 0.450382] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.450393] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.450405] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET [ 0.450410] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.450415] tegra-pmc: ### PMC reset status reg: 0x3 [ 0.501173] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.501183] tegra-pmc: Clear bootloader IO dpd settings [ 0.501202] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.501271] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.501562] iommu: Adding device 70012000.se to group 21 [ 0.502333] iommu: Adding device 7000c000.i2c to group 22 [ 0.502590] iommu: Adding device 7000c400.i2c to group 23 [ 0.502840] iommu: Adding device 7000c500.i2c to group 24 [ 0.503093] iommu: Adding device 7000c700.i2c to group 25 [ 0.503331] iommu: Adding device 7000d000.i2c to group 26 [ 0.503579] iommu: Adding device 7000d100.i2c to group 27 [ 0.503841] iommu: Adding device sdhci-tegra.3 to group 28 [ 0.503914] platform sdhci-tegra.3: domain=ffffffc0f958b9d8 allocates as[0]=ffffffc0f94304b8 [ 0.504353] iommu: Adding device sdhci-tegra.2 to group 29 [ 0.504407] platform sdhci-tegra.2: domain=ffffffc0f958bc18 allocates as[0]=ffffffc0f9430520 [ 0.505260] iommu: Adding device 700d0000.xudc to group 30 [ 0.508443] vdd-ac-bat: 5000 mV [ 0.508785] vdd-5v0-sys: 5000 mV [ 0.509762] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.509832] vdd-5v0-hdmi: 5000 mV [ 0.510236] vdd-1v8-sys: 1800 mV [ 0.510628] vdd-fan: supplied by vdd-5v0-sys [ 0.510662] vdd-fan: 5000 mV [ 0.511049] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.511100] vdd-usb-vbus: 5000 mV [ 0.511614] vdd-usb-vbus2: 5000 mV [ 0.546022] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.548423] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.549585] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.549604] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.549723] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.550048] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.558011] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.558360] SCSI subsystem initialized [ 0.558580] libata version 3.00 loaded. [ 0.558916] usbcore: registered new interface driver usbfs [ 0.558965] usbcore: registered new interface driver hub [ 0.559038] usbcore: registered new device driver usb [ 0.563224] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.568351] vdd-core: 600 <--> 1162 mV at 1125 mV [ 0.568505] random: fast init done [ 0.569402] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.572238] vdd-ddr-1v1: 1150 mV [ 0.576307] vdd-pre-reg-1v35: 1350 mV [ 0.580233] vdd-1v8: 1800 mV [ 0.584236] avdd-sys-1v2: 1200 mV [ 0.588237] vdd-pex-1v0: 1050 mV [ 0.588920] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.589468] max77620-ldo3: at 3100 mV [ 0.592245] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.592790] max77620-ldo5: at 3100 mV [ 0.596238] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [ 0.600238] avdd-1v05-pll: 1050 mV [ 0.604234] avdd-io-hdmi-dp: 1050 mV [ 0.606879] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.607190] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.607482] max77620 4-003c: max77620 probe successful [ 0.610244] media: Linux media interface: v0.10 [ 0.610298] Linux video capture interface: v2.00 [ 0.611224] pps_core: LinuxPPS API ver. 1 registered [ 0.611231] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.611251] PTP clock support registered [ 0.614631] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.615483] Advanced Linux Sound Architecture Driver Initialized. [ 0.616189] Bluetooth: Core ver 2.22 [ 0.616237] NET: Registered protocol family 31 [ 0.616241] Bluetooth: HCI device and connection manager initialized [ 0.616262] Bluetooth: HCI socket layer initialized [ 0.616271] Bluetooth: L2CAP socket layer initialized [ 0.616296] Bluetooth: SCO socket layer initialized [ 0.618064] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.618081] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.618130] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.618145] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.621888] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.623162] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.623250] vdd-3v3-sys: 3300 mV [ 0.623534] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.625055] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.625570] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.625614] vdd-3v3-sd: 3300 mV [ 0.626736] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.626777] avdd-io-edp-1v05: 1050 mV [ 0.627207] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.627241] vdd-usb-hub-en: 5000 mV [ 0.628653] camchar: rtcpu character device driver loaded [ 0.629584] extcon-gpio-states extcon:extcon@1: Cable state:1, cable id:1 [ 0.631045] clocksource: Switched to clocksource arch_sys_counter [ 0.671434] VFS: Disk quotas dquot_6.6.0 [ 0.671563] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.672052] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.672470] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.672488] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.672684] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.672689] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.672701] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.672725] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.672732] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.672746] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.672754] nvmap_page_pool_init: Total RAM pages: 1010585 [ 0.672760] nvmap_page_pool_init: nvmap page pool size: 126323 pages (493 MB) [ 0.672843] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.673345] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.674301] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.682779] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.683292] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.683675] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.683960] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.684142] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.684421] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.684426] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.684857] NET: Registered protocol family 2 [ 0.685835] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.686047] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.686554] TCP: Hash tables configured (established 32768 bind 32768) [ 0.686691] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.686771] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.687289] NET: Registered protocol family 1 [ 0.687998] RPC: Registered named UNIX socket transport module. [ 0.688003] RPC: Registered udp transport module. [ 0.688008] RPC: Registered tcp transport module. [ 0.688011] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.688028] PCI: CLS 0 bytes, default 64 [ 0.688247] Trying to unpack rootfs image as initramfs... [ 0.991317] Freeing initrd memory: 6992K [ 1.001362] host1x 50000000.host1x: initialized [ 1.003331] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.006679] audit: initializing netlink subsys (disabled) [ 1.006769] audit: type=2000 audit(0.855:1): initialized [ 1.007577] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.017532] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.019006] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.019830] 9p: Installing v9fs 9p2000 file system support [ 1.023064] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 1.023369] io scheduler noop registered [ 1.023668] io scheduler cfq registered (default) [ 1.026334] gic 702f9000.agic: GIC IRQ controller registered [ 1.029186] iommu: Adding device 702ef000.adsp to group 31 [ 1.037241] iommu: Adding device aconnect@702c0000:adsp_audio to group 32 [ 1.037369] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 1.037958] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x91c7c0e [ 1.037966] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 1.039839] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 1.039952] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 1.040048] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 1.040240] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 1.040327] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 1.040417] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 1.040499] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 1.040597] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 1.040682] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 1.040770] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 1.046880] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 1.048813] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 1.050682] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.051975] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 1.052319] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.053455] no avaiable target backlight node [ 1.053496] pwm_bl_ops are not required [ 1.053501] fail to parse max-brightness [ 1.053509] pwm-backlight pwm-backlight: fail to find platform data [ 1.053554] pwm-backlight: probe of pwm-backlight failed with error -22 [ 1.053811] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.054032] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 1.054322] Adding domain tsec-pd to PM domain host1x-pd [ 1.054466] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 1.057976] tsec 54500000.tsec: initialized [ 1.059332] tsec 54100000.tsecb: initialized [ 1.060036] Adding domain nvdec-pd to PM domain host1x-pd [ 1.063627] nvdec 54480000.nvdec: initialized [ 1.064715] Adding domain vic03-pd to PM domain host1x-pd [ 1.064892] Adding domain msenc-pd to PM domain host1x-pd [ 1.065050] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.069071] falcon 54340000.vic: initialized [ 1.070300] falcon 544c0000.nvenc: initialized [ 1.071670] falcon 54380000.nvjpg: initialized [ 1.075949] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=95 [ 1.075997] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.076029] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.076197] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.076205] display board info: id 0x0, fab 0x0 [ 1.076260] generic_infoframe_type: 0x87 [ 1.076303] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.076308] tegra_cec 70015000.tegra_cec: probed [ 1.076414] tegradc tegradc.0: DT parsed successfully [ 1.076465] tegradc tegradc.0: Display dc.ffffff800ab80000 registered with id=0 [ 1.076973] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 640x480 (on 0x0mm) pclk=25173906 [ 1.080500] tegradc tegradc.0: probed [ 1.085909] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.092712] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.093669] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check disabled [ 1.093678] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.094015] kfuse 7000fc00.kfuse: initialized [ 1.095550] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.096509] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.097857] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.097871] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.098336] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.099985] vdd-gpu: applied init 1000000uV constraint [ 1.099991] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.100401] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.104714] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.104812] No Device Node present for smmu client: serial8250 !! [ 1.104822] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.104863] iommu: Adding device serial8250 to group 33 [ 1.107363] console [ttyS0] disabled [ 1.107477] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.113899] console [ttyS0] enabled [ 1.113907] tegradc tegradc.0: fb registered [ 1.115319] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 1.116518] [drm] Initialized [ 1.122190] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [ 1.122248] tegradc tegradc.0: hdmi: tmds rate:25174K prod-setting:prod_c_hdmi_0m_54m [ 1.122826] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [ 1.122840] tegradc tegradc.0: hdmi: BL set VIC 0 [ 1.122846] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [ 1.123861] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50 [ 1.124223] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 1.124281] Extcon AUX1(HDMI) enable [ 1.125532] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 1.125614] tegradc tegradc.1: No lt-data, using default setting [ 1.125645] tegradc tegradc.1: No hpd-gpio in DT [ 1.125680] tegradc tegradc.1: DT parsed successfully [ 1.125726] tegradc tegradc.1: Display dc.ffffff800d500000 registered with id=1 [ 1.127414] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.128124] brd: module loaded [ 1.131657] edid invalid [ 1.137657] tegradc tegradc.1: probed [ 1.143332] tegradc tegradc.1: fb registered [ 1.146848] loop: module loaded [ 1.146949] tegra_profiler: version: 1.143, samples/io: 48/28 [ 1.147122] tegra_profiler: auth: init [ 1.148472] THERMAL EST: found 2 subdevs [ 1.148479] THERMAL EST num_resources: 0 [ 1.148486] [THERMAL EST subdev 0] [ 1.148494] [THERMAL EST subdev 1] [ 1.148921] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 1.148925] THERMAL EST: thz register success. [ 1.149129] THERMAL EST: end of probe, return err: 0 [ 1.150326] sd: No Scsi addr parsed to reserve index [ 1.150357] hisi_sas: driver version v1.6 [ 1.160632] libphy: Fixed MDIO Bus: probed [ 1.161334] tun: Universal TUN/TAP device driver, 1.6 [ 1.161339] tun: (C) 1999-2004 Max Krasnyansky [ 1.162103] tegradc tegradc.0: nominal-pclk:25174825 parent:25173906 div:1.0 pclk:25173906 24923052~27440532 [ 1.162192] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.162195] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.162850] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.162854] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.162912] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.162916] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.162952] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 1.162955] Copyright(c) 1999 - 2017 Intel Corporation. [ 1.163490] tegradc tegradc.1: nominal-pclk:49000000 parent:48999316 div:1.0 pclk:48999316 48510000~53410000 [ 1.164613] PPP generic driver version 2.4.2 [ 1.164764] PPP BSD Compression module registered [ 1.164768] PPP Deflate Compression module registered [ 1.164782] PPP MPPE Compression module registered [ 1.164787] NET: Registered protocol family 24 [ 1.164840] usbcore: registered new interface driver r8152 [ 1.164880] usbcore: registered new interface driver asix [ 1.164930] usbcore: registered new interface driver ax88179_178a [ 1.164966] usbcore: registered new interface driver cdc_ether [ 1.164995] usbcore: registered new interface driver net1080 [ 1.165033] usbcore: registered new interface driver cdc_subset [ 1.165066] usbcore: registered new interface driver zaurus [ 1.165105] usbcore: registered new interface driver cdc_ncm [ 1.165242] VFIO - User Level meta-driver version: 0.3 [ 1.166350] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.166362] ehci-pci: EHCI PCI platform driver [ 1.166400] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.166408] ohci-pci: OHCI PCI platform driver [ 1.166445] ohci-platform: OHCI generic platform driver [ 1.167084] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 1.168523] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 1.169093] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 1.170173] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f9626400 id [ 1.170948] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 1.171803] usbcore: registered new interface driver uas [ 1.171856] usbcore: registered new interface driver usb-storage [ 1.171932] usbcore: registered new interface driver usbserial [ 1.172638] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release [ 1.172670] tegra-xusb 70090000.xusb: xHCI Host Controller [ 1.172687] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 1.173418] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 1.173455] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 1.173616] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.173623] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.173628] usb usb1: Product: xHCI Host Controller [ 1.173632] usb usb1: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 1.173637] usb usb1: SerialNumber: 70090000.xusb [ 1.174062] hub 1-0:1.0: USB hub found [ 1.174096] hub 1-0:1.0: 5 ports detected [ 1.174612] tegra-xusb 70090000.xusb: xHCI Host Controller [ 1.174622] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 1.174694] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.174786] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.174792] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.174797] usb usb2: Product: xHCI Host Controller [ 1.174801] usb usb2: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 1.174805] usb usb2: SerialNumber: 70090000.xusb [ 1.175209] hub 2-0:1.0: USB hub found [ 1.175241] hub 2-0:1.0: 4 ports detected [ 1.176441] dp lt: state 0 (Reset), pending_lt_evt 1 [ 1.176446] dp lt: switching from state 0 (Reset) to state 0 (Reset) [ 1.176451] dp lt: state 0 (Reset), pending_lt_evt 0 [ 1.177314] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 1.177321] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 1.177768] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 1.177926] tegra-xudc-new 700d0000.xudc: device count: 1 [ 1.178051] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 1.178057] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 1.178512] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 1.178524] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 1.178535] dp lt: tx_pu: 0x20 [ 1.178896] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 1.178906] tegra-xudc-new 700d0000.xudc: vbus state: 1 [ 1.178916] tegra-xudc-new 700d0000.xudc: device mode on: 0 [ 1.178925] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0 [ 1.178946] tegra-xudc-new 700d0000.xudc: active: 0 => 1 [ 1.179524] mousedev: PS/2 mouse device common for all mice [ 1.179593] usbcore: registered new interface driver xpad [ 1.179636] dp lt: CR done [ 1.179641] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 1.179647] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 1.179700] Goodix-TS 1-0014: =======> GT911 Probe driver <============== [ 1.179704] Goodix-TS 1-0014: =======> GT911 Probe driver <============== [ 1.179708] Goodix-TS 1-0014: =======> GT911 Probe driver <============== [ 1.179713] Goodix-TS 1-0014: I2C Address: 0x14 [ 1.181643] dp lt: CE done [ 1.181648] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 1.181991] hpd: state 7 (Takeover from bootloader), hpd 1, pending_hpd_evt 1 [ 1.181996] hpd: switching from state 7 (Takeover from bootloader) to state 1 (Check Plug) [ 1.264072] tegradc tegradc.0: hdmi: edid read failed [ 1.269193] tegradc tegradc.0: hdmi: using fallback edid [ 1.269276] tegradc tegradc.0: blank - powerdown [ 1.275110] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 1.275408] tegra-i2c 7000c400.i2c: no acknowledge from address 0x14 [ 1.275443] Goodix-TS 1-0014: i2c test failed attempt 1: -121 [ 1.279252] usb usb2: usb_suspend_both: status 0 [ 1.298700] hpd: state 1 (Check Plug), hpd 1, pending_hpd_evt 0 [ 1.298706] hpd: switching from state 1 (Check Plug) to state 2 (Check EDID) [ 1.303054] hpd: state 2 (Check EDID), hpd 1, pending_hpd_evt 0 [ 1.303161] tegra-i2c 7000c400.i2c: no acknowledge from address 0x14 [ 1.303193] Goodix-TS 1-0014: i2c test failed attempt 2: -121 [ 1.308661] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 1.320284] tegradc tegradc.1: nominal-pclk:49000000 parent:48999316 div:1.0 pclk:48999316 48510000~53410000 [ 1.320379] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 1.320381] Extcon AUX1(HDMI) disable [ 1.335053] Goodix-TS 1-0014: I2C communication failure: -121 [ 1.335088] Goodix-TS: probe of 1-0014 failed with error -121 [ 1.335208] Goodix-TS 1-005d: =======> GT911 Probe driver <============== [ 1.335211] Goodix-TS 1-005d: =======> GT911 Probe driver <============== [ 1.335214] Goodix-TS 1-005d: =======> GT911 Probe driver <============== [ 1.335218] Goodix-TS 1-005d: I2C Address: 0x5d [ 1.336083] tegradc tegradc.0: unblank [ 1.378117] tegradc tegradc.0: nominal-pclk:74250000 parent:74250000 div:1.0 pclk:74250000 73507500~80932500 [ 1.378196] tegradc tegradc.0: hdmi: tmds rate:74250K prod-setting:prod_c_hdmi_54m_75m [ 1.379278] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 1.386013] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 1.386017] Extcon AUX1(HDMI) enable [ 1.396174] tegradc tegradc.0: sync windows ret = 247 [ 1.414422] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 1.414428] tegradc tegradc.1: blank - powerdown [ 1.435165] tegra-i2c 7000c400.i2c: no acknowledge from address 0x5d [ 1.435199] Goodix-TS 1-005d: i2c test failed attempt 1: -121 [ 1.448201] dp lt: state 5 (link training pass), pending_lt_evt 1 [ 1.448204] dp lt: switching from state 5 (link training pass) to state 0 (Reset) [ 1.448208] dp lt: state 0 (Reset), pending_lt_evt 0 [ 1.448213] dp lt: link training force disable [ 1.448216] dp lt: switching from state 0 (Reset) to state 4 (link training fail/disable) [ 1.463171] tegra-i2c 7000c400.i2c: no acknowledge from address 0x5d [ 1.463203] Goodix-TS 1-005d: i2c test failed attempt 2: -121 [ 1.469078] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 1.469088] tegradc tegradc.1: unblank [ 1.487043] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.491044] Goodix-TS 1-005d: I2C communication failure: -121 [ 1.491070] Goodix-TS: probe of 1-005d failed with error -121 [ 1.499054] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 1.503437] tegradc tegradc.1: nominal-pclk:49000000 parent:48999316 div:1.0 pclk:48999316 48510000~53410000 [ 1.505059] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 1.508887] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 1.514234] dp lt: state 4 (link training fail/disable), pending_lt_evt 1 [ 1.514237] dp lt: switching from state 4 (link training fail/disable) to state 0 (Reset) [ 1.514241] dp lt: state 0 (Reset), pending_lt_evt 0 [ 1.515456] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 1.515606] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 1.515610] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 1.516063] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 1.516073] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 1.516079] dp lt: tx_pu: 0x20 [ 1.516985] dp lt: CR done [ 1.516988] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 1.516992] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 1.518969] dp lt: CE done [ 1.518972] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 1.519606] usb 1-2: New USB device found, idVendor=0451, idProduct=8142 [ 1.519611] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=1 [ 1.519615] usb 1-2: SerialNumber: 62070061A7A1 [ 1.520468] hub 1-2:1.0: USB hub found [ 1.520544] hub 1-2:1.0: 4 ports detected [ 1.535689] tegradc tegradc.1: sync windows ret = 246 [ 1.553127] extcon-disp-state extcon:disp-state: cable 51 state 1 [ 1.553130] Extcon HDMI: HPD enabled [ 1.553154] tegradc tegradc.0: hdmi: plugged [ 1.553408] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 1.553413] tegradc tegradc.1: blank - powerdown [ 1.602340] dp lt: state 5 (link training pass), pending_lt_evt 1 [ 1.602343] dp lt: switching from state 5 (link training pass) to state 0 (Reset) [ 1.602347] dp lt: state 0 (Reset), pending_lt_evt 0 [ 1.602351] dp lt: link training force disable [ 1.602354] dp lt: switching from state 0 (Reset) to state 4 (link training fail/disable) [ 1.619923] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 1.622067] rtc rtc1: alarm rtc device [ 1.622079] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.622096] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.622484] i2c /dev entries driver [ 1.623238] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 1.623251] tegradc tegradc.1: unblank [ 1.624280] i2c i2c-6: Added multiplexed i2c bus 7 [ 1.624672] i2c i2c-6: Added multiplexed i2c bus 8 [ 1.624677] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 1.625285] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [ 1.650300] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [ 1.657666] tegradc tegradc.1: nominal-pclk:49000000 parent:48999316 div:1.0 pclk:48999316 48510000~53410000 [ 1.659294] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 1.663198] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 1.668588] dp lt: state 4 (link training fail/disable), pending_lt_evt 1 [ 1.668591] dp lt: switching from state 4 (link training fail/disable) to state 0 (Reset) [ 1.668594] dp lt: state 0 (Reset), pending_lt_evt 0 [ 1.669808] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 1.669957] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 1.669961] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 1.670414] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 1.670423] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 1.670430] dp lt: tx_pu: 0x20 [ 1.671337] dp lt: CR done [ 1.671340] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 1.671344] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 1.673323] dp lt: CE done [ 1.673326] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 1.675992] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 1.678223] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 1.678227] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 1.678534] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.678547] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 1.678554] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 1.678689] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.678699] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 1.678705] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 1.678848] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.678856] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 1.678861] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 1.679059] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 1.679618] tegra_aotag tegra-aotag: Registering sensor 0 [ 1.679662] tegra_aotag tegra-aotag: Invalid temp readout [ 1.679683] tegra_aotag tegra-aotag: Invalid temp readout [ 1.679699] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 1.679707] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 1.680583] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.680597] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 1.680784] tegra_aotag tegra-aotag: Invalid temp readout [ 1.680807] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 1.681223] parse_throttle_dt_data: Num cap clks = 6 [ 1.681228] parse_throttle_dt_data: clk=cclk_g type=2 [ 1.681234] parse_throttle_dt_data: clk=gpu type=4 [ 1.681254] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 1.681271] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 1.681291] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 1.681294] parse_throttle_dt_data: clk=emc type=3 [ 1.681673] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.681800] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.681940] tegra_throttle_probe: probe successful. #cdevs=4 [ 1.682433] PWM shared data node NULL, parse phandle failed [ 1.682439] pwm_fan_driver: probe of pwm-fan failed with error -22 [ 1.682471] PWM shared data node NULL, parse phandle failed [ 1.682477] pwm_fan_driver: probe of pwm-backlight failed with error -22 [ 1.682504] PWM shared data node NULL, parse phandle failed [ 1.682509] pwm_fan_driver: probe of pwm-led-support-ctrl failed with error -22 [ 1.684849] device-mapper: uevent: version 1.0.3 [ 1.685308] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 1.688020] tegra210-cpufreq cpufreq: probe()...completed [ 1.688823] sdhci: Secure Digital Host Controller Interface driver [ 1.688825] sdhci: Copyright(c) Pierre Ossman [ 1.688826] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.689171] sdhci-tegra sdhci-tegra.3: Client registration for eMC Successful [ 1.690092] tegradc tegradc.1: sync windows ret = 246 [ 1.693950] sdhci-tegra sdhci-tegra.2: Client registration for eMC Successful [ 1.698964] tegra-se 70012000.se: tegra_se_probe: complete [ 1.699476] hidraw: raw HID events driver (C) Jiri Kosina [ 1.701760] usbcore: registered new interface driver usbhid [ 1.701762] usbhid: USB HID core driver [ 1.703971] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 1.704138] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 1.705988] nvpmodel: initialized successfully [ 1.706948] usbcore: registered new interface driver snd-usb-audio [ 1.707006] extcon-disp-state extcon:disp-state: cable 44 state 1 [ 1.707009] Extcon DP: HPD enabled [ 1.707015] No Device Node present for smmu client: snd-soc-dummy !! [ 1.707020] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.707035] hpd: Display connected, hpd_switch 1 [ 1.707039] hpd: switching from state 2 (Check EDID) to state 4 (Enabled) [ 1.707057] iommu: Adding device snd-soc-dummy to group 34 [ 1.718275] OPE platform probe [ 1.718358] OPE platform probe successful [ 1.718385] OPE platform probe [ 1.719109] OPE platform probe successful [ 1.720402] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 1.727322] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 1.727685] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 1.731067] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA 64-bit with 64 bit addr [ 1.734252] u32 classifier [ 1.734254] Actions configured [ 1.734327] Initializing XFRM netlink socket [ 1.735048] NET: Registered protocol family 10 [ 1.735730] NET: Registered protocol family 17 [ 1.735742] NET: Registered protocol family 15 [ 1.735815] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.735860] Bluetooth: RFCOMM socket layer initialized [ 1.735870] Bluetooth: RFCOMM ver 1.11 [ 1.735875] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.735880] Bluetooth: HIDP socket layer initialized [ 1.735898] 9pnet: Installing 9P2000 support [ 1.735933] Key type dns_resolver registered [ 1.736355] Registered cp15_barrier emulation handler [ 1.736362] Registered setend emulation handler [ 1.737462] registered taskstats version 1 [ 1.737981] Adding domain ve2-pd to PM domain host1x-pd [ 1.738232] Adding domain ve-pd to PM domain host1x-pd [ 1.739065] mmc1: SDHCI controller on sdhci-tegra.2 [sdhci-tegra.2] using ADMA 64-bit with 64 bit addr [ 1.740389] isp 54600000.isp: initialized [ 1.742635] isp 54680000.isp: initialized [ 1.753274] last reset is due to software reset [ 1.753279] KERNEL: PMC reset status reg: 0x3 [ 1.753340] BL: PMC reset status reg: 0x3 [ 1.753342] BL: PMIC poweroff Event Recorder: 0x0 [ 1.754855] clk_cbus_recalc_rate: no gbus parent [ 1.754861] clk_cbus_round_rate: no gbus parent [ 1.754864] clk_cbus_round_rate: no gbus parent [ 1.754871] clk_cbus_recalc_rate: no gbus parent [ 1.754979] clk_cbus_recalc_rate: no gbus parent [ 1.754982] clk_cbus_round_rate: no gbus parent [ 1.754984] clk_cbus_round_rate: no gbus parent [ 1.754988] clk_cbus_recalc_rate: no gbus parent [ 1.755701] tegra_dvfs: GPU-cap: registered [ 1.755755] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 1.755757] tegra dvfs: vdd-core: nominal 1125mV, offset 600000uV, step 12500uV, scaling enabled [ 1.755760] tegra dvfs: vdd-gpu: nominal 1078mV, offset 708000uV, step 10000uV, scaling enabled [ 1.757214] tegra_dvfs: vdd-gpu-vts: registered [ 1.757896] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 1.758515] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 1.759768] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 1.766724] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 1.773549] input: gpio-keys as /devices/gpio-keys/input/input1 [ 1.774887] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 1.781883] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 1.782139] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 1.782455] mmcblk0: mmc0:0001 DG4016 14.7 GiB [ 1.786586] mmcblk0boot0: mmc0:0001 DG4016 partition 1 4.00 MiB [ 1.790725] mmcblk0boot1: mmc0:0001 DG4016 partition 2 4.00 MiB [ 1.794953] mmcblk0rpmb: mmc0:0001 DG4016 partition 3 4.00 MiB [ 1.797637] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 [ 1.800968] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 1.807966] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 1.814144] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-04 23:12:54 UTC (947027574) [ 1.815095] usb 1-2.1: new high-speed USB device number 3 using tegra-xusb [ 1.815663] vi 54080000.vi: vi_probe: ++ [ 1.818571] vi 54080000.vi: initialized [ 1.820627] vi 54080000.vi: subdev nvcsi--2 bound [ 1.820641] vi 54080000.vi: subdev imx219 7-0010 bound [ 1.821365] vi 54080000.vi: subdev nvcsi--1 bound [ 1.821372] vi 54080000.vi: subdev imx219 8-0010 bound [ 1.823210] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 1.827291] mmcblk mmc0:0001: Card claimed for testing. [ 1.828627] Disable partitions left on by BL [ 1.828629] disb [ 1.828676] bwmgr: missing cdev-type property [ 1.828808] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.828815] DRAM derating cdev registered. [ 1.829779] ALSA device list: [ 1.829782] #0: tegra-hda at 0x70038000 irq 80 [ 1.830268] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 1.833352] Freeing unused kernel memory: 8576K [ 1.835817] usb 1-2.1: New USB device found, idVendor=1b55, idProduct=0121 [ 1.835821] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1.835824] usb 1-2.1: Product: FPReader [ 1.835827] usb 1-2.1: Manufacturer: ZKTeco Inc. [ 1.835829] usb 1-2.1: SerialNumber: 4019211660144 [ 1.838083] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 1.845055] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 1.858886] mmc1: host does not support reading read-only switch, assuming write-enable [ 1.867971] Root device found: mmcblk0p1 [ 1.869410] Found dev node: /dev/mmcblk0p1 [ 1.908634] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 1.910506] Rootfs mounted over mmcblk0p1 [ 1.925044] Switching from initrd to actual rootfs [ 1.925071] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.931123] usb 1-2.2: new full-speed USB device number 4 using tegra-xusb [ 1.952845] usb 1-2.2: New USB device found, idVendor=08bb, idProduct=27c4 [ 1.952850] usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.952854] usb 1-2.2: Product: USB AUDIO DAC [ 1.952857] usb 1-2.2: Manufacturer: BurrBrown from Texas Instruments [ 1.962201] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 1.969159] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 1.975917] hid-generic 0003:08BB:27C4.0001: hidraw0: USB HID v1.00 Device [BurrBrown from Texas Instruments USB AUDIO DAC] on usb-70090000.xusb-2.2/input2 [ 1.977288] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 1.984223] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 1.998773] mmc1: hw tuning done ... [ 1.998816] mmc1: new ultra high speed SDR104 SDXC card at address 59b4 [ 1.999130] mmcblk1: mmc1:59b4 USDU1 57.5 GiB [ 2.000510] mmcblk1: p1 [ 2.002128] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 2.009113] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 2.024674] systemd[1]: System time before build time, advancing clock. [ 2.039657] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.050976] cgroup: cgroup2: unknown option "nsdelegate" [ 2.064031] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 2.064797] systemd[1]: Detected architecture arm64. [ 2.086956] systemd[1]: Set hostname to . [ 2.099546] tegra_cec 70015000.tegra_cec: physical address: 10:00. [ 2.164112] tegra_cec 70015000.tegra_cec: Sent res: -113. [ 2.164116] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 2.166512] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 2.166521] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 2.263528] random: systemd: uninitialized urandom read (16 bytes read) [ 2.263746] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 2.263970] random: systemd: uninitialized urandom read (16 bytes read) [ 2.265531] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 2.265571] random: systemd: uninitialized urandom read (16 bytes read) [ 2.265990] systemd[1]: Created slice User and Session Slice. [ 2.266036] systemd[1]: Reached target Swap. [ 2.266071] systemd[1]: Reached target User and Group Name Lookups. [ 2.314782] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 2.367066] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.369095] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.439325] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [ 2.444032] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 2.452138] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 2.459810] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 2.459830] cpu-throttle-alert cooling device registered. [ 2.459980] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 2.459996] gpu-throttle-alert cooling device registered. [ 2.460180] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 2.460229] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 2.460247] hot-surface-alert cooling device registered. [ 2.466502] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 2.473478] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.473483] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.473486] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.473490] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.473494] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.473516] pci 0000:00:02.0: [10de:0faf] type 01 class 0x060400 [ 2.473578] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.473740] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.473859] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 2.473881] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.473910] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit pref] [ 2.473930] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.474053] pci 0000:01:00.0: supports D1 D2 [ 2.474056] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.483131] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.483165] pci 0000:00:02.0: BAR 15: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.483169] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.483176] pci 0000:01:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.483193] pci 0000:01:00.0: BAR 2: assigned [mem 0x20004000-0x20004fff 64bit pref] [ 2.483209] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.483216] pci 0000:00:02.0: PCI bridge to [bus 01] [ 2.483220] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.483226] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.483492] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 2.483496] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.483500] pcie_pme 0000:00:02.0:pcie001: service driver pcie_pme loaded [ 2.483594] aer 0000:00:02.0:pcie002: service driver aer loaded [ 2.483770] r8168 0000:01:00.0: enabling device (0000 -> 0003) [ 2.483785] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 2.504003] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 2.505444] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 2.505469] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 2.517836] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 2.523121] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:ea:28:0b from device tree [ 2.523572] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 2.523589] r8168 Copyright (C) 2017 Realtek NIC software team This program comes with ABSOLUTELY NO WARRANTY; for details, please see . This is free software, and you are welcome to redistribute it under certain conditions; see . [ 2.525079] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 2.525104] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 2.574129] systemd-journald[1948]: Received request to flush runtime journal from PID 1 [ 2.912234] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 2.918991] regmap_util_write_table_8:regmap_util_write_table:-121 [ 2.932759] imx219 7-0010: Error writing mode [ 2.939705] vi 54080000.vi: calibration failed with -121 error [ 3.033332] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 3.040536] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 3.103647] tegra-asoc: sound: ASoC: CODEC DAI wm8960-sound not registered [ 3.104043] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.172393] tegra-asoc: sound: snd_soc_register_card failed (-517) [ 3.514527] using random self ethernet address [ 3.564300] using random host ethernet address [ 3.735283] usb0: HOST MAC 92:7a:1d:71:53:9e [ 3.735322] usb0: MAC 92:7a:1d:71:53:9f [ 3.735345] tegra-xudc-new 700d0000.xudc: ep 0 (type: 0, dir: out) enabled [ 3.788275] l4tbr0: port 1(usb0) entered blocking state [ 3.788280] l4tbr0: port 1(usb0) entered disabled state [ 3.788447] device usb0 entered promiscuous mode [ 3.845087] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 4.031597] android_work: did not send uevent (0 0 (null)) [ 4.104615] android_work: sent uevent USB_STATE=CONNECTED [ 4.159227] android_work: sent uevent USB_STATE=DISCONNECTED [ 4.241449] random: crng init done [ 4.244856] random: 7 urandom warning(s) missed due to ratelimiting [ 4.252130] android_work: sent uevent USB_STATE=CONNECTED [ 4.258723] configfs-gadget gadget: high-speed config #1: c [ 4.258757] tegra-xudc-new 700d0000.xudc: ep 5 (type: 3, dir: in) enabled [ 4.258774] tegra-xudc-new 700d0000.xudc: ep 3 (type: 2, dir: in) enabled [ 4.258789] tegra-xudc-new 700d0000.xudc: ep 2 (type: 2, dir: out) enabled [ 4.258820] tegra-xudc-new 700d0000.xudc: ep 9 (type: 3, dir: in) enabled [ 4.258896] android_work: sent uevent USB_STATE=CONFIGURED [ 4.260984] tegra-xudc-new 700d0000.xudc: ep 7 (type: 2, dir: in) enabled [ 4.261002] tegra-xudc-new 700d0000.xudc: ep 4 (type: 2, dir: out) enabled [ 4.263227] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready [ 4.634600] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 4.705861] tegradc tegradc.0: unblank [ 4.711314] tegradc tegradc.1: unblank [ 5.027323] tegradc tegradc.0: blank - powerdown [ 5.079627] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 5.079630] Extcon AUX1(HDMI) disable [ 5.099913] tegradc tegradc.1: blank - powerdown [ 5.154270] dp lt: state 5 (link training pass), pending_lt_evt 1 [ 5.154273] dp lt: switching from state 5 (link training pass) to state 0 (Reset) [ 5.154275] dp lt: state 0 (Reset), pending_lt_evt 0 [ 5.154280] dp lt: link training force disable [ 5.154282] dp lt: switching from state 0 (Reset) to state 4 (link training fail/disable) [ 5.188409] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 5.249911] tegradc tegradc.0: blank - powerdown [ 5.249932] tegradc tegradc.0: unblank [ 5.286256] tegradc tegradc.0: nominal-pclk:74250000 parent:74250000 div:1.0 pclk:74250000 73507500~80932500 [ 5.286334] tegradc tegradc.0: hdmi: tmds rate:74250K prod-setting:prod_c_hdmi_54m_75m [ 5.287396] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 5.290834] tegra_i2c_handle_xfer_error: 11 callbacks suppressed [ 5.290838] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50 [ 5.295082] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 5.295084] Extcon AUX1(HDMI) enable [ 5.313058] tegradc tegradc.0: unblank [ 5.313070] tegradc tegradc.1: blank - powerdown [ 5.313314] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 5.313328] tegradc tegradc.1: unblank [ 5.344111] tegradc tegradc.1: nominal-pclk:49000000 parent:48999316 div:1.0 pclk:48999316 48510000~53410000 [ 5.345755] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 5.349682] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 5.354935] dp lt: state 4 (link training fail/disable), pending_lt_evt 1 [ 5.354938] dp lt: switching from state 4 (link training fail/disable) to state 0 (Reset) [ 5.354941] dp lt: state 0 (Reset), pending_lt_evt 0 [ 5.356131] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 5.356269] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 5.356272] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 5.356713] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 5.356720] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 5.356725] dp lt: tx_pu: 0x20 [ 5.357608] dp lt: CR done [ 5.357611] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 5.357613] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 5.359525] dp lt: CE done [ 5.359527] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 5.364057] tegradc tegradc.1: unblank [ 5.570163] tegradc tegradc.0: blank - powerdown [ 5.621034] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 5.621036] Extcon AUX1(HDMI) disable [ 5.641503] tegradc tegradc.1: blank - powerdown [ 5.692761] dp lt: state 5 (link training pass), pending_lt_evt 1 [ 5.692764] dp lt: switching from state 5 (link training pass) to state 0 (Reset) [ 5.692766] dp lt: state 0 (Reset), pending_lt_evt 0 [ 5.692771] dp lt: link training force disable [ 5.692773] dp lt: switching from state 0 (Reset) to state 4 (link training fail/disable) [ 5.762083] tegradc tegradc.0: blank - powerdown [ 5.762096] tegradc tegradc.0: unblank [ 5.798188] tegradc tegradc.0: nominal-pclk:74250000 parent:74250000 div:1.0 pclk:74250000 73507500~80932500 [ 5.798266] tegradc tegradc.0: hdmi: tmds rate:74250K prod-setting:prod_c_hdmi_54m_75m [ 5.799298] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 5.802736] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50 [ 5.812539] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 5.812541] Extcon AUX1(HDMI) enable [ 5.820837] tegradc tegradc.0: unblank [ 5.820860] tegradc tegradc.1: blank - powerdown [ 5.820869] tegradc tegradc.1: unblank [ 5.851257] tegradc tegradc.1: nominal-pclk:49000000 parent:48999316 div:1.0 pclk:48999316 48510000~53410000 [ 5.852859] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 5.856825] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 5.861734] dp lt: state 4 (link training fail/disable), pending_lt_evt 1 [ 5.861736] dp lt: switching from state 4 (link training fail/disable) to state 0 (Reset) [ 5.861739] dp lt: state 0 (Reset), pending_lt_evt 0 [ 5.862922] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 5.863049] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 5.863052] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 5.863491] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 5.863498] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 5.863503] dp lt: tx_pu: 0x20 [ 5.864586] dp lt: CR done [ 5.864589] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 5.864592] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 5.866497] dp lt: CE done [ 5.866500] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 5.866627] tegradc tegradc.1: unblank [ 6.579096] tegradc tegradc.0: blank - powerdown [ 6.632943] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 6.632945] Extcon AUX1(HDMI) disable [ 6.653400] tegradc tegradc.1: blank - powerdown [ 6.716028] dp lt: state 5 (link training pass), pending_lt_evt 1 [ 6.716031] dp lt: switching from state 5 (link training pass) to state 0 (Reset) [ 6.716033] dp lt: state 0 (Reset), pending_lt_evt 0 [ 6.716038] dp lt: link training force disable [ 6.716040] dp lt: switching from state 0 (Reset) to state 4 (link training fail/disable) [ 7.207278] zram: Added device: zram0 [ 7.211926] zram: Added device: zram1 [ 7.218821] zram: Added device: zram2 [ 7.221918] zram: Added device: zram3 [ 7.256646] zram0: detected capacity change from 0 to 519413760 [ 7.278780] Adding 507236k swap on /dev/zram0. Priority:5 extents:1 across:507236k SS [ 7.280644] zram1: detected capacity change from 0 to 519413760 [ 7.306711] Adding 507236k swap on /dev/zram1. Priority:5 extents:1 across:507236k SS [ 7.309964] zram2: detected capacity change from 0 to 519413760 [ 7.330041] Adding 507236k swap on /dev/zram2. Priority:5 extents:1 across:507236k SS [ 7.331965] zram3: detected capacity change from 0 to 519413760 [ 7.349269] Adding 507236k swap on /dev/zram3. Priority:5 extents:1 across:507236k SS [ 7.579881] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 7.580972] eth0: 0xffffff800ac71000, 00:04:4b:ea:28:0b, IRQ 405 [ 7.692494] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9.747591] r8168: eth0: link up [ 9.747685] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 10.403575] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 10.461819] tegradc tegradc.0: blank - powerdown [ 10.461832] tegradc tegradc.0: unblank [ 10.497888] tegradc tegradc.0: nominal-pclk:74250000 parent:74250000 div:1.0 pclk:74250000 73507500~80932500 [ 10.499476] tegradc tegradc.0: hdmi: tmds rate:74250K prod-setting:prod_c_hdmi_54m_75m [ 10.500571] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 10.503966] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50 [ 10.508799] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 10.508801] Extcon AUX1(HDMI) enable [ 10.519806] tegradc tegradc.0: unblank [ 10.520199] tegradc tegradc.1: blank - powerdown [ 10.520208] tegradc tegradc.1: unblank [ 10.550798] tegradc tegradc.1: nominal-pclk:49000000 parent:48999316 div:1.0 pclk:48999316 48510000~53410000 [ 10.553812] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 10.557797] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 10.563204] dp lt: state 4 (link training fail/disable), pending_lt_evt 1 [ 10.563208] dp lt: switching from state 4 (link training fail/disable) to state 0 (Reset) [ 10.563210] dp lt: state 0 (Reset), pending_lt_evt 0 [ 10.564416] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 10.564555] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 10.564561] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 10.565002] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 10.565009] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 10.565014] dp lt: tx_pu: 0x20 [ 10.565940] dp lt: CR done [ 10.565944] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 10.565949] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 10.568607] dp lt: CE done [ 10.568611] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 10.574337] tegradc tegradc.1: unblank [ 10.672187] l4tbr0: port 1(usb0) entered blocking state [ 10.672192] l4tbr0: port 1(usb0) entered forwarding state [ 10.672284] IPv6: ADDRCONF(NETDEV_UP): l4tbr0: link is not ready [ 10.751084] IPv6: ADDRCONF(NETDEV_CHANGE): l4tbr0: link becomes ready [ 10.879345] tegradc tegradc.0: blank - powerdown [ 10.934266] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 10.934268] Extcon AUX1(HDMI) disable [ 10.954629] tegradc tegradc.1: blank - powerdown [ 11.018428] dp lt: state 5 (link training pass), pending_lt_evt 1 [ 11.018431] dp lt: switching from state 5 (link training pass) to state 0 (Reset) [ 11.018433] dp lt: state 0 (Reset), pending_lt_evt 0 [ 11.018438] dp lt: link training force disable [ 11.018439] dp lt: switching from state 0 (Reset) to state 4 (link training fail/disable) [ 11.052459] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 11.106504] tegradc tegradc.0: blank - powerdown [ 11.106517] tegradc tegradc.0: unblank [ 11.142470] tegradc tegradc.0: nominal-pclk:74250000 parent:74250000 div:1.0 pclk:74250000 73507500~80932500 [ 11.142552] tegradc tegradc.0: hdmi: tmds rate:74250K prod-setting:prod_c_hdmi_54m_75m [ 11.143579] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 11.147003] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50 [ 11.150229] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 11.150231] Extcon AUX1(HDMI) enable [ 11.160896] tegradc tegradc.0: unblank [ 11.160908] tegradc tegradc.1: blank - powerdown [ 11.160917] tegradc tegradc.1: unblank [ 11.191356] tegradc tegradc.1: nominal-pclk:49000000 parent:48999316 div:1.0 pclk:48999316 48510000~53410000 [ 11.193022] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 11.196948] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 11.202182] dp lt: state 4 (link training fail/disable), pending_lt_evt 1 [ 11.202185] dp lt: switching from state 4 (link training fail/disable) to state 0 (Reset) [ 11.202187] dp lt: state 0 (Reset), pending_lt_evt 0 [ 11.203375] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 11.203509] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 11.203513] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 11.203950] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 11.203957] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 11.203962] dp lt: tx_pu: 0x20 [ 11.205044] dp lt: CR done [ 11.205047] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 11.205049] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 11.206948] dp lt: CE done [ 11.206951] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 11.211558] tegradc tegradc.1: unblank [ 16.145436] tegradc tegradc.0: unblank [ 16.145611] tegradc tegradc.1: unblank [ 16.208120] tegradc tegradc.0: unblank [ 16.208304] tegradc tegradc.1: unblank [ 16.274517] tegradc tegradc.0: unblank [ 16.274669] tegradc tegradc.1: blank - powerdown [ 16.336756] dp lt: state 5 (link training pass), pending_lt_evt 1 [ 16.336759] dp lt: switching from state 5 (link training pass) to state 0 (Reset) [ 16.336761] dp lt: state 0 (Reset), pending_lt_evt 0 [ 16.336766] dp lt: link training force disable [ 16.336768] dp lt: switching from state 0 (Reset) to state 4 (link training fail/disable) [ 16.382057] tegradc tegradc.0: blank - powerdown [ 16.444281] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 16.444301] Extcon AUX1(HDMI) disable [ 16.464323] tegradc tegradc.1: blank - powerdown [ 16.488310] tegradc tegradc.1: blank - powerdown [ 16.488320] tegradc tegradc.1: unblank [ 16.518781] tegradc tegradc.1: nominal-pclk:49000000 parent:48999316 div:1.0 pclk:48999316 48510000~53410000 [ 16.520398] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200000 did not specify bpp [ 16.524325] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 16.529587] dp lt: state 4 (link training fail/disable), pending_lt_evt 1 [ 16.529589] dp lt: switching from state 4 (link training fail/disable) to state 0 (Reset) [ 16.529592] dp lt: state 0 (Reset), pending_lt_evt 0 [ 16.530779] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 16.530921] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 16.530925] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 16.531364] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 16.531372] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 16.531378] dp lt: tx_pu: 0x20 [ 16.532263] dp lt: CR done [ 16.532266] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 16.532270] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 16.534192] dp lt: CE done [ 16.534194] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 16.535897] tegradc tegradc.1: unblank [ 16.535905] tegradc tegradc.0: blank - powerdown [ 16.582799] tegradc tegradc.0: blank - powerdown [ 16.582810] tegradc tegradc.0: unblank [ 16.618754] tegradc tegradc.0: nominal-pclk:74250000 parent:74250000 div:1.0 pclk:74250000 73507500~80932500 [ 16.618830] tegradc tegradc.0: hdmi: tmds rate:74250K prod-setting:prod_c_hdmi_54m_75m [ 16.619921] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 16.623410] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50 [ 16.626745] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 16.626749] Extcon AUX1(HDMI) enable [ 16.635672] tegradc tegradc.0: unblank [ 16.635711] tegradc tegradc.1: unblank [ 31.859241] vdd-fan: disabling [ 31.859246] vdd-usb-vbus: disabling [ 31.859248] vdd-usb-vbus2: disabling [ 31.859258] vddio-sdmmc-ap: disabling [ 31.859348] vdd-3v3-sd: disabling [ 31.859354] vdd-usb-hub-en: disabling [ 80.659086] FAN rising trip_level:1 cur_temp:51000 trip_temps[2]:61000 ac@vsm:~$