[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-80a468da) [0000.131] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.139] Power-up reason: pmc por [0000.142] No Battery Present [0000.145] pmic max77620 reset reason [0000.148] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.154] Platform has DDR4 type RAM [0000.157] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x314c6 [0000.173] Entering ramdump check [0000.176] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.189] Sdram initialization is successful [0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] Read GPT from (4:0) [0000.402] Csd NumOfBlocks=62333952 [0000.407] Set High speed to 1 [0000.411] Error mask set in wait for cmd complete with error 0x3 in HwSdmmcWaitForCommandComplete func at 278 line [0000.421] Command complete wait failed with error 0x3 Interrupt 0x18001 [0000.427] Number of retries left 4 [0000.439] Using GPT Primary to query partitions [0000.444] Loading Tboot-CPU binary [0000.453] Verifying TBC in OdmNonSecureSBK mode [0000.463] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.470] Bootloader downloaded successfully. [0000.474] Downloaded Tboot-CPU binary to 0xa0000258 [0000.479] MAX77620_GPIO5 configured [0000.482] CPU power rail is up [0000.485] CPU clock enabled [0000.489] Performing RAM repair [0000.492] Updating A64 Warmreset Address to 0xa00002e9 [0000.497] Loading NvTbootBootloaderDTB [0000.524] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.596] Bootloader DTB Load Address: 0x83000000 [0000.600] Loading NvTbootKernelDTB [0000.626] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.698] Kernel DTB Load Address: 0x83100000 [0000.705] Loading cboot binary [0000.734] Verifying EBT in OdmNonSecureSBK mode [0000.776] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.783] Bootloader downloaded successfully. [0000.787] Read PT from (2:0) [0000.803] Using BFS PT to query partitions [0000.807] PT: Partition NCT NOT found ! [0000.810] Warning: Find Partition via PT Failed [0000.815] Next binary entry address: 0x92c00258 [0000.819] BoardId: 3448 [0000.824] Overriding pmu board id with proc board id [0000.828] Display board id is not available [0000.859] Verifying SC7EntryFw in OdmNonSecureSBK mode [0000.913] /bpmp deleted [0000.915] SC7EntryFw header found loaded at 0xff700000 [0001.105] OVR2 PMIC [0001.107] Bpmp FW successfully loaded [0001.113] WB0 init successfully at 0xff780000 [0001.117] Set NvDecSticky Bits [0001.121] GSC2 address ff53fffc value c0edbbcc [0001.127] GSC MC Settings done [0001.133] TOS Image length 53680 [0001.136] Monitor size 53680 [0001.138] OS size 0 [0001.147] Secure Os AES-CMAC Verification Success! [0001.152] TOS image cipher info: plaintext [0001.156] Loading and Validation of Secure OS Successful [0001.172] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.176] NvTbootPackSdramParams: start. [0001.182] NvTbootPackSdramParams: done. [0001.185] Tegraboot started after 52336 us [0001.189] Basic modules init took 800951 us [0001.193] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB [0001.199] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.204] Storage Device Read Time = 124 ms, Read Size = 2241 KB [0001.210] Storage Device Write Time = 0 ms, Write Size = 0 KB [0001.216] Next stage binary read took 26326 us [0001.220] Carveout took -38010 us [0001.223] CPU initialization took 372559 us [0001.227] Total time taken by TegraBoot 1161826 us [0001.232] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):41d46a9cf NOTICE: BL31: Built : 15:58:25, Sep 24 2020 ERROR: Error initializing runtime service trusty_fast [0001.354] RamCode = 0 [0001.359] LPDDR4 Training: Read DT: Number of tables = 2 [0001.364] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.376] EMC Training Successful [0001.379] 408000 not found in DVFS table [0001.386] RamCode = 0 [0001.389] DT Write: emc-table@204000 succeeded [0001.395] DT Write: emc-table@1600000 succeeded [0001.399] LPDDR4 Training: Write DT: Number of tables = 2 [0001.441] [0001.442] Debug Init done [0001.445] Marked DTB cacheable [0001.448] Bootloader DTB loaded at 0x83000000 [0001.453] Marked DTB cacheable [0001.456] Kernel DTB loaded at 0x83100000 [0001.460] DeviceTree Init done [0001.472] Pinmux applied successfully [0001.477] gicd_base: 0x50041000 [0001.480] gicc_base: 0x50042000 [0001.483] Interrupts Init done [0001.487] Using base:0x60005090 & irq:208 for tick-timer [0001.493] Using base:0x60005098 for delay-timer [0001.497] platform_init_timer: DONE [0001.500] Timer(tick) Init done [0001.504] osc freq = 38400 khz [0001.508] [0001.510] Welcome to L4T Cboot [0001.512] [0001.514] Cboot Version: 00.00.2018.01-t210-d8cbdfce [0001.519] calling constructors [0001.522] initializing heap [0001.524] initializing threads [0001.527] initializing timers [0001.530] creating bootstrap completion thread [0001.534] top of bootstrap2() [0001.537] CPU: ARM Cortex A57 [0001.540] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.545] initializing platform [0001.552] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.557] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.561] Macronix QSPI chip present [0001.565] SPI device register [0001.568] init boot device [0001.570] allocating memory for boot device(SPI) [0001.575] registering boot device [0001.594] sdmmc node status = okay [0001.598] sdcard instance = 0 [0001.600] sdcard gpio handle 0x56 [0001.604] sdcard gpio pin 0xc9 [0001.607] sdcard gpio flags 0x0 [0001.610] vmmc-supply 0x99 [0001.612] Instance: 0 [0001.614] Allocating memory for context [0001.618] enabling clock [0001.621] sd card init [0001.623] Check card present and stable [0001.627] Send command 0 [0001.651] Send command 3 [0001.655] Set RCA for the card [0001.658] Query card specific data by command 9 [0001.665] Parse CSD data [0001.667] Send command 7 [0001.678] Calling sd device register [0001.681] Init sdcard [0001.683] Allocating memory for boot device [0001.687] Registering user device [0001.700] Enable APE clock [0001.703] Un-powergate APE partition [0001.706] of_register: registering tegra_udc to of_hal [0001.712] of_register: registering inv20628-driver to of_hal [0001.717] of_register: registering ads1015-driver to of_hal [0001.723] of_register: registering lp8557-bl-driver to of_hal [0001.729] of_register: registering bq2419x_charger to of_hal [0001.734] of_register: registering bq27441_fuel_gauge to of_hal [0001.746] gpio framework initialized [0001.749] of_register: registering tca9539_gpio to of_hal [0001.755] of_register: registering tca9539_gpio to of_hal [0001.760] of_register: registering i2c_bus_driver to of_hal [0001.765] of_register: registering i2c_bus_driver to of_hal [0001.771] of_register: registering i2c_bus_driver to of_hal [0001.777] pmic framework initialized [0001.780] of_register: registering max77620_pmic to of_hal [0001.786] regulator framework initialized [0001.789] of_register: registering tps65132_bl_driver to of_hal [0001.795] initializing target [0001.801] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.809] board ID = D78, board SKU = 0 [0001.813] Skipping Z3! [0001.818] fixed regulator driver initialized [0001.836] initializing OF layer [0001.839] NCK carveout not present [0001.842] Skipping dts_overrides [0001.846] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.863] I2C Bus Init done [0001.866] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.876] I2C Bus Init done [0001.879] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.889] I2C Bus Init done [0001.892] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.902] I2C Bus Init done [0001.905] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.915] I2C Bus Init done [0001.918] of_children_init: Ops found for compatible string maxim,max77620 [0001.928] max77620_init using irq 118 [0001.933] register 'maxim,max77620' pmic [0001.937] gpio_driver_register: register 'max77620-gpio' driver [0001.943] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.954] I2C Bus Init done [0001.958] NCK carveout not present [0001.968] Find /i2c@7000c000's alias i2c0 [0001.971] get eeprom at 1-a0, size 256, type 0 [0001.980] Find /i2c@7000c500's alias i2c2 [0001.984] get eeprom at 3-a0, size 256, type 0 [0001.989] get eeprom at 3-ae, size 256, type 0 [0001.993] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.998] I2C slave not started [0002.001] I2C write failed [0002.004] Writing offset failed [0002.007] eeprom_init: EEPROM read failed [0002.011] pm_ids_update: eeprom init failed [0002.015] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.045] pm_ids_update: The pm board id is 3448-0000-400 [0002.052] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.060] pm_ids_update: pm id update successful [0002.064] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.094] pm_ids_update: The pm board id is 3449-0000-400 [0002.101] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.109] pm_ids_update: pm id update successful [0002.140] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.145] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.154] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.160] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.168] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e7:17:cc [0002.175] Plugin Manager: Parse ODM data 0x00094000 [0002.185] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.200] Find /i2c@7000c000's alias i2c0 [0002.203] get eeprom at 1-a0, size 256, type 0 [0002.212] Find /i2c@7000c500's alias i2c2 [0002.216] get eeprom at 3-a0, size 256, type 0 [0002.221] get eeprom at 3-ae, size 256, type 0 [0002.225] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.230] I2C slave not started [0002.233] I2C write failed [0002.236] Writing offset failed [0002.239] eeprom_init: EEPROM read failed [0002.243] pm_ids_update: eeprom init failed [0002.247] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.277] pm_ids_update: The pm board id is 3448-0000-400 [0002.284] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.291] pm_ids_update: pm id update successful [0002.295] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.325] pm_ids_update: The pm board id is 3449-0000-400 [0002.332] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.339] pm_ids_update: pm id update successful [0002.369] Add serial number:1422919080440 as DT property [0002.377] Applying platform configs [0002.384] platform-init is not present. Skipping [0002.389] calling apps_init() [0002.414] Found 14 GPT partitions in "sd0" [0002.418] Proceeding to Cold Boot [0002.421] starting app android_boot_app [0002.425] Device state: unlocked [0002.428] display console init [0002.437] could not find regulator [0002.460] hdmi cable not connected [0002.463] is_hdmi_needed: HDMI not connected, returning false [0002.469] hdDT entry for leds-pwm not found m[0002.476] i is not connected [0002.479] sor0 is not supported [0002.482] display_console_init: no valid display out_type [0002.490] subnode volume_up is not found ! [0002.494] subnode back is not found ! [0002.498] subnode volume_down is not found ! [0002.502] subnode menu is not found ! [0002.506] Gpio keyboard init success [0002.552] found decompressor handler: lz4-legacy [0002.567] decompressing blob (type 1)... [0002.600] display_resolution: No display init [0002.605] Failed to retrieve display resolution [0002.609] Could not load/initialize BMP blob...ignoring [0002.661] decompressor handler not found [0002.665] load_firmware_blob: Firmware blob loaded, entries=2 [0002.671] -------> se_aes_verify_sbk_clear: 747 [0002.675] se_aes_verify_sbk_clear: Error [0002.679] bl_battery_charging: connected to external power supply [0002.686] xusb is supported [0002.692] error while finding nvidia,portmap [0003.197] xusb blob version 0 size 124416 [0003.201] firmware size 124416 [0003.205] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0003.220] xhci0: 64 bytes context size, 32-bit DMA [0003.260] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.280] uhub0: on usbus0 [0003.930] uhub0: 9 ports with 9 removable, self powered [0004.930] failed to get HID devices [0004.933] failed to init xhci or no usb device attached [0004.941] display_console_ioctl: No display init [0004.945] switch_backlight failed [0004.952] device_query_partition_size: failed to open partition sd0:MSC ! [0004.958] MSC Partition not found [0004.965] device_query_partition_size: failed to open partition sd0:USP ! [0004.971] USP partition read failed! [0004.975] blob_init: blob-partition USP header read failed [0004.980] android_boot Unable to update recovery partition [0004.986] kfs_getpartname: name = LNX [0004.989] Loading kernel from LNX [0005.087] load kernel from storage [0005.099] decompressor handler not found [0005.156] Successfully loaded kernel and ramdisk images [0005.163] display_resolution: No display init [0005.167] Failed to retrieve display resolution [0005.171] bmp blob is not loaded and initialized [0005.176] Failed to display boot-logo [0005.179] NCK carveout not present [0005.183] Skipping dts_overrides [0005.186] NCK carveout not present [0005.196] Find /i2c@7000c000's alias i2c0 [0005.200] get eeprom at 1-a0, size 256, type 0 [0005.209] Find /i2c@7000c500's alias i2c2 [0005.213] get eeprom at 3-a0, size 256, type 0 [0005.217] get eeprom at 3-ae, size 256, type 0 [0005.221] pm_ids_update: Updating 1,a0, size 256, type 0 [0005.227] I2C slave not started [0005.230] I2C write failed [0005.232] Writing offset failed [0005.235] eeprom_init: EEPROM read failed [0005.239] pm_ids_update: eeprom init failed [0005.243] pm_ids_update: Updating 3,a0, size 256, type 0 [0005.273] pm_ids_update: The pm board id is 3448-0000-400 [0005.280] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0005.288] pm_ids_update: pm id update successful [0005.293] pm_ids_update: Updating 3,ae, size 256, type 0 [0005.323] pm_ids_update: The pm board id is 3449-0000-400 [0005.329] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0005.337] pm_ids_update: pm id update successful [0005.368] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.374] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0005.382] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.388] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0005.396] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e7:17:cc [0005.403] Plugin Manager: Parse ODM data 0x00094000 [0005.413] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0005.421] Add serial number:1422919080440 as DT property [0005.430] "bpmp" doesn't exist, creating [0005.436] Updated bpmp info to DTB [0005.441] Updated initrd info to DTB [0005.444] "proc-board" doesn't exist, creating [0005.450] Updated board info to DTB [0005.453] "pmu-board" doesn't exist, creating [0005.459] Updated board info to DTB [0005.462] "display-board" doesn't exist, creating [0005.468] Updated board info to DTB [0005.471] "reset" doesn't exist, creating [0005.475] Updated reset info to DTB [0005.479] display_console_ioctl: No display init [0005.483] display_console_ioctl: No display init [0005.488] display_console_ioctl: No display init [0005.492] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_m [0005.527] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0005.532] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.545] Updated bootarg info to DTB [0005.549] Adding uuid 00000001644495872000000004fd00c0 to DT [0005.555] Adding eks info 0 to DT [0005.560] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0005.566] Updated memory info to DTB [0005.575] set vdd_core voltage to 1125 mv [0005.579] setting 'vdd-core' regulator to 1125000 micro volts [0005.600] Found secure-pmc; disable BPMP U-Boot 2016.07-ge6da093be3 (Sep 24 2020 - 15:58:38 -0700) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 844 bytes read in 146 ms (4.9 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 5488163 bytes read in 355 ms (14.7 MiB/s) Retrieving file: /boot/Image 34330632 bytes read in 1534 ms (21.3 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 earl ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 000000008317d33d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-2280) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Thu Sep 24 16:07:04 PDT 2020 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.007182] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.513339] Host read timeout at address 545c00c4 [ 1.746990] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.754567] imx219 7-0010: board setup failed [ 1.782914] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.790442] imx219 8-0010: board setup failed [ 2.597977] cgroup: cgroup2: unknown option "nsdelegate" [ 4.293291] using random self ethernet address [ 4.302244] using random host ethernet address [ 4.327405] random: crng init done [ 4.330812] random: 7 urandom warning(s) missed due to ratelimiting [ 5.623509] using random self ethernet address [ 5.649597] using random host ethernet address Ubuntu 18.04.5 LTS jetson ttyS0 jetson login: