[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-tegra (yoctopc@yoctopc) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Jun 19 17:58:55 +03 2020 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92cb0000 [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] On node 0 totalpages: 1039872 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 519168 pages, LIFO batch:31 [ 0.000000] Normal zone: 8136 pages used for memmap [ 0.000000] Normal zone: 520704 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefb2000 s61592 r8192 d32616 u102400 [ 0.000000] pcpu-alloc: s61592 r8192 d32616 u102400 alloc=25*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb0000 is_hdmi_initialised=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29336(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3562288K/4159488K available (15230K kernel code, 2926K rwdata, 6560K rodata, 8576K init, 609K bss, 122064K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f60000 ( 15232 KB) [ 0.000000] .rodata : 0xffffff8008f60000 - 0xffffff80095d0000 ( 6592 KB) [ 0.000000] .init : 0xffffff80095d0000 - 0xffffff8009e30000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e30000 - 0xffffff800a10b808 ( 2927 KB) [ 0.000000] .bss : 0xffffff800a10b808 - 0xffffff800a1a3dbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.001830] Console: colour dummy device 80x25 [ 0.001849] console [tty0] enabled [ 0.001865] kmemleak: Kernel memory leak detector disabled [ 0.001885] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.001898] pid_max: default: 32768 minimum: 301 [ 0.002350] Security Framework initialized [ 0.002574] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.002583] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003750] ftrace: allocating 47001 entries in 184 pages [ 0.177122] sched-energy: CPU device node has no sched-energy-costs [ 0.177157] ASID allocator initialised with 65536 entries [ 0.216090] tegra-id: chipid=22117. [ 0.216104] tegra-id: opt_subrevision=0. [ 0.216122] Tegra Speedo/IDDQ fuse revision 4 [ 0.216127] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.216131] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0 [ 0.216137] Tegra: CPU Speedo Value 2061, SoC Speedo Value 1967, GPU Speedo Value 2046 [ 0.216141] Tegra: CPU IDDQ Value 1800, SoC IDDQ Value 2136, GPU IDDQ Value 2390 [ 0.216159] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1 [ 0.216173] DTS File Name: arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0002-p3449-0000-b00.dts [ 0.216180] DTB Build time: Jun 19 2020 18:47:31 [ 0.265068] CPU1: Booted secondary processor [411fd071] [ 0.297007] CPU2: Booted secondary processor [411fd071] [ 0.328975] CPU3: Booted secondary processor [411fd071] [ 0.329069] Brought up 4 CPUs [ 0.329076] SMP: Total of 4 processors activated. [ 0.329084] CPU features: detected feature: 32-bit EL0 Support [ 0.329354] CPU: All CPU(s) started at EL2 [ 0.329373] alternatives: patching kernel code [ 0.337763] devtmpfs: initialized [ 0.375801] Initilizing CustomIPI irq domain [ 0.376202] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.376223] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.387733] pinctrl core: initialized pinctrl subsystem [ 0.388436] OS set in device tree is not L4T. [ 0.388860] regulator-dummy: no parameters [ 0.389198] Initializing plugin-manager [ 0.389314] Plugin module not found [ 0.389541] node /plugin-manager/fragement@0 match with board >=3448-0002-100 [ 0.390092] node /plugin-manager/fragment@1 match with board >=3448-0002-101 [ 0.390601] node /plugin-manager/fragment@3 match with board >=3448-0002-100 [ 0.391292] node /plugin-manager/fragement@6 match with odm-data enable-tegra-wdt [ 0.391711] node /plugin-manager/fragement@8 match with odm-data enable-tegra-wdt [ 0.392345] node /plugin-manager/fragement@10 match with board >=3448-0002-300 [ 0.394523] node /plugin-manager/fragement@11 match with board >=3448-0002-300 [ 0.398086] NET: Registered protocol family 16 [ 0.401619] pstore: using zlib compression [ 0.401666] console [pstore-1] enabled [ 0.401671] pstore: Registered ramoops as persistent store backend [ 0.401676] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.417091] cpuidle: using governor menu [ 0.421519] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.423186] vdso: 2 pages (1 code @ ffffff8008f67000, 1 data @ ffffff8009e34000) [ 0.423210] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.425685] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.428249] tegra_powergate_init: DONE [ 0.428264] DTS File Name: arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0002-p3449-0000-b00.dts [ 0.428272] DTB Build time: Jun 19 2020 18:47:31 [ 0.430087] Tegra reboot handler registered. [ 0.434653] iommu: Adding device tegra-carveouts to group 0 [ 0.434798] platform tegra-carveouts: domain=ffffffc0f9428318 allocates as[0]=ffffffc0f9bcc0a8 [ 0.435166] iommu: Adding device smmu_test to group 1 [ 0.435212] platform smmu_test: domain=ffffffc0f9428558 allocates as[0]=ffffffc0f9bcc110 [ 0.436037] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.436090] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.436143] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.436153] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.436176] mc-err: mcerr ops are set to t21x [ 0.446136] iommu: Adding device 70090000.xusb to group 2 [ 0.446430] iommu: Adding device 70006000.serial to group 3 [ 0.446509] platform 70006000.serial: domain=ffffffc0f94b9618 allocates as[0]=ffffffc0f9bcc178 [ 0.446944] iommu: Adding device 70006040.serial to group 4 [ 0.447220] iommu: Adding device 70006200.serial to group 5 [ 0.447440] iommu: Adding device sound to group 6 [ 0.447488] platform sound: domain=ffffffc0f94b9b58 allocates as[0]=ffffffc0f9bcc1e0 [ 0.448071] iommu: Adding device 7000d400.spi to group 7 [ 0.448328] iommu: Adding device 7000d600.spi to group 8 [ 0.448661] iommu: Adding device 50000000.host1x to group 9 [ 0.448933] iommu: Adding device 54080000.vi to group 10 [ 0.449452] iommu: Adding device 54600000.isp to group 11 [ 0.449706] iommu: Adding device 54680000.isp to group 12 [ 0.449969] iommu: Adding device tegradc.0 to group 13 [ 0.450046] platform tegradc.0: domain=ffffffc0f94c6918 allocates as[0]=ffffffc0f9bcc248 [ 0.454235] platform tegradc.0: IOVA linear map 0x0000000092cb0000(800000) [ 0.454629] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.454962] iommu: Adding device tegradc.1 to group 14 [ 0.455013] platform tegradc.1: domain=ffffffc0f94c6b58 allocates as[0]=ffffffc0f9bcc2b0 [ 0.459173] platform tegradc.1: IOVA linear map 0x0000000092cb0000(800000) [ 0.459568] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.459827] iommu: Adding device 54340000.vic to group 15 [ 0.460020] iommu: Adding device 544c0000.nvenc to group 16 [ 0.460218] iommu: Adding device 54500000.tsec to group 17 [ 0.460435] iommu: Adding device 54100000.tsecb to group 18 [ 0.460638] iommu: Adding device 54480000.nvdec to group 19 [ 0.460824] iommu: Adding device 54380000.nvjpg to group 20 [ 0.461912] iommu: Adding device 546c0000.i2c to group 21 [ 0.462237] iommu: Adding device 57000000.gpu to group 22 [ 0.462291] platform 57000000.gpu: domain=ffffffc0f94d5b58 allocates as[0]=ffffffc0f9bcc318 [ 0.462330] platform 57000000.gpu: domain=ffffffc0f94d5b58 allocates as[1]=ffffffc0f9bcc380 [ 0.462374] platform 57000000.gpu: domain=ffffffc0f94d5b58 allocates as[2]=ffffffc0f9bcc3e8 [ 0.462416] platform 57000000.gpu: domain=ffffffc0f94d5b58 allocates as[3]=ffffffc0f9bcc450 [ 0.463306] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.463318] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.463329] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [ 0.463333] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.463339] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.513173] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.513183] tegra-pmc: Clear bootloader IO dpd settings [ 0.513202] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.513269] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.513569] iommu: Adding device 70012000.se to group 23 [ 0.514347] iommu: Adding device 7000c000.i2c to group 24 [ 0.514600] iommu: Adding device 7000c400.i2c to group 25 [ 0.514850] iommu: Adding device 7000c500.i2c to group 26 [ 0.515110] iommu: Adding device 7000c700.i2c to group 27 [ 0.515355] iommu: Adding device 7000d000.i2c to group 28 [ 0.515636] iommu: Adding device 7000d100.i2c to group 29 [ 0.515908] iommu: Adding device sdhci-tegra.3 to group 30 [ 0.515960] platform sdhci-tegra.3: domain=ffffffc0f9571cd8 allocates as[0]=ffffffc0f9bcc4b8 [ 0.516401] iommu: Adding device sdhci-tegra.2 to group 31 [ 0.516457] platform sdhci-tegra.2: domain=ffffffc0f9571f18 allocates as[0]=ffffffc0f9bcc520 [ 0.517339] iommu: Adding device 700d0000.xudc to group 32 [ 0.520652] vdd-ac-bat: 5000 mV [ 0.521040] vdd-5v0-sys: 5000 mV [ 0.522039] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.522087] vdd-5v0-hdmi: 5000 mV [ 0.522470] vdd-1v8-sys: 1800 mV [ 0.522857] vdd-fan: supplied by vdd-5v0-sys [ 0.522894] vdd-fan: 5000 mV [ 0.523312] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.523348] vdd-usb-vbus: 5000 mV [ 0.523869] vdd-usb-vbus2: 5000 mV [ 0.554106] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.556496] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.557856] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.557876] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.557914] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.558318] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.566392] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.566742] SCSI subsystem initialized [ 0.566966] libata version 3.00 loaded. [ 0.567250] usbcore: registered new interface driver usbfs [ 0.567306] usbcore: registered new interface driver hub [ 0.567382] usbcore: registered new device driver usb [ 0.571456] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.577158] random: fast init done [ 0.577167] vdd-core: 600 <--> 1162 mV at 1075 mV [ 0.578197] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.580999] vdd-ddr-1v1: 1150 mV [ 0.585089] vdd-pre-reg-1v35: 1350 mV [ 0.588991] vdd-1v8: 1800 mV [ 0.592991] avdd-sys-1v2: 1200 mV [ 0.596991] vdd-pex-1v0: 1050 mV [ 0.597656] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.598192] max77620-ldo3: at 3100 mV [ 0.600997] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.601543] max77620-ldo5: at 3100 mV [ 0.604992] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [ 0.608997] avdd-1v05-pll: 1050 mV [ 0.612992] avdd-io-hdmi-dp: 1050 mV [ 0.615590] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.615882] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.616171] max77620 4-003c: max77620 probe successful [ 0.618837] media: Linux media interface: v0.10 [ 0.618893] Linux video capture interface: v2.00 [ 0.619814] pps_core: LinuxPPS API ver. 1 registered [ 0.619822] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.619849] PTP clock support registered [ 0.623697] tegra_fiq_debugger_init: found FIQ source (IRQ 98) [ 0.630149] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.630999] Advanced Linux Sound Architecture Driver Initialized. [ 0.631694] Bluetooth: Core ver 2.22 [ 0.631749] NET: Registered protocol family 31 [ 0.631752] Bluetooth: HCI device and connection manager initialized [ 0.631768] Bluetooth: HCI socket layer initialized [ 0.631776] Bluetooth: L2CAP socket layer initialized [ 0.631825] Bluetooth: SCO socket layer initialized [ 0.633705] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.633721] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.633766] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.633780] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.637168] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.638408] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.638473] vdd-3v3-sys: 3300 mV [ 0.638735] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.640308] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.640783] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.640850] vdd-3v3-sd: 3300 mV [ 0.641834] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.641877] avdd-io-edp-1v05: 1050 mV [ 0.642294] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.642332] vdd-usb-hub-en: 5000 mV [ 0.643840] camchar: rtcpu character device driver loaded [ 0.644620] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [ 0.645992] clocksource: Switched to clocksource arch_sys_counter [ 0.686488] VFS: Disk quotas dquot_6.6.0 [ 0.686625] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.687111] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.687569] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.687590] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.687821] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.687828] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.687840] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.687868] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.687874] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.687890] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.687897] nvmap_page_pool_init: Total RAM pages: 1009356 [ 0.687902] nvmap_page_pool_init: nvmap page pool size: 126169 pages (492 MB) [ 0.687998] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.688419] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.689243] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.699085] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.699515] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.699757] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.699964] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.700139] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.700413] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.700420] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.700865] NET: Registered protocol family 2 [ 0.701859] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.702126] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.702676] TCP: Hash tables configured (established 32768 bind 32768) [ 0.702829] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.702911] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.703337] NET: Registered protocol family 1 [ 0.704095] RPC: Registered named UNIX socket transport module. [ 0.704100] RPC: Registered udp transport module. [ 0.704103] RPC: Registered tcp transport module. [ 0.704107] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.704120] PCI: CLS 0 bytes, default 64 [ 0.704358] Trying to unpack rootfs image as initramfs... [ 0.938514] Freeing initrd memory: 5356K [ 0.948664] host1x 50000000.host1x: initialized [ 0.950650] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.953885] audit: initializing netlink subsys (disabled) [ 0.953960] audit: type=2000 audit(0.799:1): initialized [ 0.954838] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 0.964914] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.966464] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.967271] 9p: Installing v9fs 9p2000 file system support [ 0.970757] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 0.970905] io scheduler noop registered [ 0.971198] io scheduler cfq registered (default) [ 0.973886] gic 702f9000.agic: GIC IRQ controller registered [ 0.976907] iommu: Adding device 702ef000.adsp to group 33 [ 0.986136] iommu: Adding device aconnect@702c0000:adsp_audio to group 34 [ 0.986297] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 0.986916] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x8209c11 [ 0.986925] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 0.988565] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 0.988671] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 0.988776] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 0.988964] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 0.989052] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 0.989138] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 0.989228] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 0.989316] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 0.989404] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 0.989488] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 0.995813] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 0.997543] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 0.999538] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.000800] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 1.001166] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.002433] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.002664] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 1.002913] Adding domain tsec-pd to PM domain host1x-pd [ 1.005357] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 1.006356] tsec 54500000.tsec: initialized [ 1.007925] tsec 54100000.tsecb: initialized [ 1.008635] Adding domain nvdec-pd to PM domain host1x-pd [ 1.012090] nvdec 54480000.nvdec: initialized [ 1.013170] Adding domain vic03-pd to PM domain host1x-pd [ 1.013348] Adding domain msenc-pd to PM domain host1x-pd [ 1.013508] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.017724] falcon 54340000.vic: initialized [ 1.018956] falcon 544c0000.nvenc: initialized [ 1.020271] falcon 54380000.nvjpg: initialized [ 1.024740] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97 [ 1.024810] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.024845] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.024982] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.025120] display board info: id 0x0, fab 0x0 [ 1.025126] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.025130] tegra_cec 70015000.tegra_cec: probed [ 1.025188] generic_infoframe_type: 0x87 [ 1.025333] tegradc tegradc.0: DT parsed successfully [ 1.025379] tegradc tegradc.0: Display dc.ffffff800ab40000 registered with id=0 [ 1.025916] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 1920x1080 (on 0x0mm) pclk=148350781 [ 1.029579] tegradc tegradc.0: probed [ 1.034977] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.041665] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.042718] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.043244] kfuse 7000fc00.kfuse: initialized [ 1.044845] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.045898] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.047803] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.047824] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.048365] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.050138] vdd-gpu: applied init 1000000uV constraint [ 1.050149] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.050616] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.055534] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.055709] No Device Node present for smmu client: serial8250 !! [ 1.055722] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.055801] iommu: Adding device serial8250 to group 35 [ 1.059014] console [ttyS0] disabled [ 1.059086] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.059185] console [ttyS0] enabled [ 1.060113] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 1.060407] serial-tegra 70006200.serial: RX in PIO mode [ 1.060503] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 1.061594] [drm] Initialized [ 1.063665] Console: switching to colour frame buffer device 240x67 [ 1.063790] tegradc tegradc.0: fb registered [ 1.071335] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [ 1.071395] tegradc tegradc.0: hdmi: tmds rate:148351K prod-setting:prod_c_hdmi_75m_150m [ 1.071948] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [ 1.071961] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [ 1.074236] brd: module loaded [ 1.079780] loop: module loaded [ 1.079887] tegra_profiler: version: 1.139, samples/io: 47/27 [ 1.079994] tegra_profiler: auth: init [ 1.081386] THERMAL EST: found 2 subdevs [ 1.081395] THERMAL EST num_resources: 0 [ 1.081401] [THERMAL EST subdev 0] [ 1.081410] [THERMAL EST subdev 1] [ 1.081907] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 1.081912] THERMAL EST: thz register success. [ 1.082125] THERMAL EST: end of probe, return err: 0 [ 1.083449] hisi_sas: driver version v1.6 [ 1.089719] libphy: Fixed MDIO Bus: probed [ 1.090606] tun: Universal TUN/TAP device driver, 1.6 [ 1.090612] tun: (C) 1999-2004 Max Krasnyansky [ 1.091625] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.091631] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.091682] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.091688] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.091736] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.091739] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.091792] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 1.091797] Copyright(c) 1999 - 2017 Intel Corporation. [ 1.092925] PPP generic driver version 2.4.2 [ 1.093158] PPP BSD Compression module registered [ 1.093164] PPP Deflate Compression module registered [ 1.093208] PPP MPPE Compression module registered [ 1.093216] NET: Registered protocol family 24 [ 1.093292] usbcore: registered new interface driver r8152 [ 1.093338] usbcore: registered new interface driver asix [ 1.093388] usbcore: registered new interface driver ax88179_178a [ 1.093441] usbcore: registered new interface driver cdc_ether [ 1.093479] usbcore: registered new interface driver net1080 [ 1.093517] usbcore: registered new interface driver cdc_subset [ 1.093557] usbcore: registered new interface driver zaurus [ 1.093613] usbcore: registered new interface driver cdc_ncm [ 1.093788] VFIO - User Level meta-driver version: 0.3 [ 1.095264] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.095292] ehci-pci: EHCI PCI platform driver [ 1.095345] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.095356] ohci-pci: OHCI PCI platform driver [ 1.095401] ohci-platform: OHCI generic platform driver [ 1.098264] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 1.098426] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 1.098431] Extcon AUX1(HDMI) enable [ 1.098927] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 1.099217] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 1.099289] tegradc tegradc.1: No lt-data, using default setting [ 1.099320] tegradc tegradc.1: No hpd-gpio in DT [ 1.099351] tegradc tegradc.1: DT parsed successfully [ 1.099408] tegradc tegradc.1: Display dc.ffffff800d4c0000 registered with id=1 [ 1.100288] tegra-xusb 70090000.xusb: extcon 0: ffffffc0fa5d2c00 id [ 1.101253] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.101827] usbcore: registered new interface driver uas [ 1.101900] usbcore: registered new interface driver usb-storage [ 1.102071] usbcore: registered new interface driver usbserial [ 1.106408] tegra-xudc-new 700d0000.xudc: device count: 1 [ 1.107950] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release [ 1.108006] tegra-xusb 70090000.xusb: xHCI Host Controller [ 1.108031] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 1.108824] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 1.108881] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 1.109102] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.109108] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.109114] usb usb1: Product: xHCI Host Controller [ 1.109119] usb usb1: Manufacturer: Linux 4.9.140-tegra xhci-hcd [ 1.109123] usb usb1: SerialNumber: 70090000.xusb [ 1.109342] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 1.109356] tegra-xudc-new 700d0000.xudc: vbus state: 0 [ 1.109397] tegra-xudc-new 700d0000.xudc: entering ELPG [ 1.109677] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 1.110220] hub 1-0:1.0: USB hub found [ 1.110418] hub 1-0:1.0: 5 ports detected [ 1.111314] mousedev: PS/2 mouse device common for all mice [ 1.111459] usbcore: registered new interface driver xpad [ 1.111550] tegra-xusb 70090000.xusb: xHCI Host Controller [ 1.111640] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 1.111773] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.111873] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.111880] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.111886] usb usb2: Product: xHCI Host Controller [ 1.111890] usb usb2: Manufacturer: Linux 4.9.140-tegra xhci-hcd [ 1.111895] usb usb2: SerialNumber: 70090000.xusb [ 1.116441] hub 2-0:1.0: USB hub found [ 1.116478] hub 2-0:1.0: 4 ports detected [ 1.118385] tegradc tegradc.1: probed [ 1.120207] tegradc tegradc.1: fb registered [ 1.123896] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 1.123903] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 1.123912] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 1.123927] tegradc tegradc.1: blank - powerdown [ 1.123948] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 1.123955] Extcon DP: HPD disabled [ 1.123960] hpd: hpd_switch 0 [ 1.123965] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 1.123974] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 1.123981] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 1.141274] tegradc tegradc.0: nominal-pclk:148351648 parent:148350781 div:1.0 pclk:148350781 146868084~161703244 [ 1.214059] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 1.230275] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 1.232418] rtc rtc1: alarm rtc device [ 1.232431] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 1.232449] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 1.232818] i2c /dev entries driver [ 1.233467] tegradc tegradc.0: blank - powerdown [ 1.234547] i2c i2c-6: Added multiplexed i2c bus 7 [ 1.234955] i2c i2c-6: Added multiplexed i2c bus 8 [ 1.234960] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 1.235499] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [ 1.258788] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 1.258880] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.258908] imx219 7-0010: board setup failed [ 1.258969] imx219: probe of 7-0010 failed with error -121 [ 1.259340] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [ 1.278537] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 1.278540] Extcon AUX1(HDMI) disable [ 1.282616] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 1.282706] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.282734] imx219 8-0010: board setup failed [ 1.282788] imx219: probe of 8-0010 failed with error -121 [ 1.283583] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 1.285889] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 1.285894] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 1.286232] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.286245] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 1.286252] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 1.286393] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.286402] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 1.286408] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 1.286558] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.286565] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 1.286570] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 1.286753] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 1.287288] tegra_aotag tegra-aotag: Registering sensor 0 [ 1.287332] tegra_aotag tegra-aotag: Invalid temp readout [ 1.287352] tegra_aotag tegra-aotag: Invalid temp readout [ 1.287368] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 1.287376] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 1.288326] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.288340] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 1.288526] tegra_aotag tegra-aotag: Invalid temp readout [ 1.288548] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 1.288996] parse_throttle_dt_data: Num cap clks = 6 [ 1.289000] parse_throttle_dt_data: clk=cclk_g type=2 [ 1.289007] parse_throttle_dt_data: clk=gpu type=4 [ 1.289025] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 1.289041] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 1.289061] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 1.289064] parse_throttle_dt_data: clk=emc type=3 [ 1.289434] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.289562] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.289695] tegra_throttle_probe: probe successful. #cdevs=4 [ 1.290370] FAN dev name: pwm-fan [ 1.290414] FAN:gpio request success. [ 1.290467] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 1.290698] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 1.290808] pwm_fan_driver pwm-fan: fan tach request irq success [ 1.290814] pwm_fan_driver pwm-fan: tach period: 1000 [ 1.290892] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 1.290896] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 1.290900] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 1.290904] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 1.290908] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 1.290912] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 1.290915] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 1.290919] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 1.290923] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 1.290926] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 1.291429] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds. [ 1.291695] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1) [ 1.292536] device-mapper: uevent: version 1.0.3 [ 1.292993] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 1.295657] tegra210-cpufreq cpufreq: probe()...completed [ 1.296560] sdhci: Secure Digital Host Controller Interface driver [ 1.296562] sdhci: Copyright(c) Pierre Ossman [ 1.296563] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.296914] sdhci-tegra sdhci-tegra.3: Client registration for eMC Successful [ 1.299885] sdhci-tegra sdhci-tegra.2: Client registration for eMC Successful [ 1.304794] tegra-se 70012000.se: tegra_se_probe: complete [ 1.305321] hidraw: raw HID events driver (C) Jiri Kosina [ 1.306869] tegradc tegradc.0: unblank [ 1.307006] usbcore: registered new interface driver usbhid [ 1.307007] usbhid: USB HID core driver [ 1.309323] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 1.309495] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 1.311544] nvpmodel: initialized successfully [ 1.312721] usbcore: registered new interface driver snd-usb-audio [ 1.312778] No Device Node present for smmu client: snd-soc-dummy !! [ 1.312782] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.312800] iommu: Adding device snd-soc-dummy to group 36 [ 1.318447] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 1.334664] OPE platform probe [ 1.334753] OPE platform probe successful [ 1.335053] OPE platform probe [ 1.335140] OPE platform probe successful [ 1.342018] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA 64-bit with 64 bit addr [ 1.346058] mmc1: SDHCI controller on sdhci-tegra.2 [sdhci-tegra.2] using ADMA 64-bit with 64 bit addr [ 1.348192] tegradc tegradc.0: nominal-pclk:148500000 parent:148500000 div:1.0 pclk:148500000 147015000~161865000 [ 1.348289] tegradc tegradc.0: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_75m_150m [ 1.349391] tegradc tegradc.0: hdmi: get RGB quant from EDID. [ 1.349398] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 1.362398] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 1.362531] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 1.362657] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 1.362784] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 1.362913] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 1.363038] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 1.363165] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 1.363294] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 1.363421] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 1.363547] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 1.375618] u32 classifier [ 1.375619] Actions configured [ 1.375688] Initializing XFRM netlink socket [ 1.376396] NET: Registered protocol family 10 [ 1.377023] NET: Registered protocol family 17 [ 1.377034] NET: Registered protocol family 15 [ 1.377106] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.377155] Bluetooth: RFCOMM socket layer initialized [ 1.377164] Bluetooth: RFCOMM ver 1.11 [ 1.377168] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.377172] Bluetooth: HIDP socket layer initialized [ 1.377189] 9pnet: Installing 9P2000 support [ 1.377225] Key type dns_resolver registered [ 1.377624] Registered cp15_barrier emulation handler [ 1.377629] Registered setend emulation handler [ 1.378709] registered taskstats version 1 [ 1.379226] Adding domain ve2-pd to PM domain host1x-pd [ 1.379474] Adding domain ve-pd to PM domain host1x-pd [ 1.381554] isp 54600000.isp: initialized [ 1.382540] isp 54680000.isp: initialized [ 1.384472] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 1.384475] Extcon AUX1(HDMI) enable [ 1.384868] tegradc tegradc.0: sync windows ret = 250 [ 1.385409] mmc1: host does not support reading read-only switch, assuming write-enable [ 1.389653] mmc1: new high speed SDXC card at address aaaa [ 1.392693] last reset is due to power on reset [ 1.392695] KERNEL: PMC reset status reg: 0x0 [ 1.392772] BL: PMC reset status reg: 0x0 [ 1.392774] BL: PMIC poweroff Event Recorder: 0x80 [ 1.393732] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 1.394267] clk_cbus_recalc_rate: no gbus parent [ 1.394270] clk_cbus_round_rate: no gbus parent [ 1.394272] clk_cbus_round_rate: no gbus parent [ 1.394277] clk_cbus_recalc_rate: no gbus parent [ 1.394368] clk_cbus_recalc_rate: no gbus parent [ 1.394371] clk_cbus_round_rate: no gbus parent [ 1.394372] clk_cbus_round_rate: no gbus parent [ 1.394375] clk_cbus_recalc_rate: no gbus parent [ 1.394414] mmcblk0: mmc0:0001 DG4016 14.7 GiB [ 1.394602] mmcblk0boot0: mmc0:0001 DG4016 partition 1 4.00 MiB [ 1.395054] tegra_dvfs: GPU-cap: registered [ 1.395113] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 1.395115] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled [ 1.395117] tegra dvfs: vdd-gpu: nominal 1068mV, offset 708000uV, step 10000uV, scaling enabled [ 1.395333] mmcblk0boot1: mmc0:0001 DG4016 partition 2 4.00 MiB [ 1.395914] mmcblk0rpmb: mmc0:0001 DG4016 partition 3 4.00 MiB [ 1.396614] tegra_dvfs: vdd-gpu-vts: registered [ 1.397224] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 [ 1.397335] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 1.397973] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 1.398489] input: gpio-keys as /devices/gpio-keys/input/input1 [ 1.398568] mmcblk1: mmc1:aaaa SB64G 59.5 GiB [ 1.403264] mmcblk1: p1 [ 1.417040] extcon-disp-state extcon:disp-state: cable 51 state 1 [ 1.417042] Extcon HDMI: HPD enabled [ 1.417056] tegradc tegradc.0: hdmi: plugged [ 1.430757] tegra_rtc 7000e000.rtc: setting system clock to 2020-06-22 09:22:14 UTC (1592817734) [ 1.431857] vi 54080000.vi: vi_probe: ++ [ 1.434676] vi 54080000.vi: initialized [ 1.436008] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.436760] vi 54080000.vi: subdev nvcsi--2 bound [ 1.436862] vi 54080000.vi: subdev nvcsi--1 bound [ 1.437097] mmcblk mmc1:aaaa: Card claimed for testing. [ 1.437106] mmcblk mmc0:0001: Card claimed for testing. [ 1.438444] Disable partitions left on by BL [ 1.438447] disb [ 1.438494] bwmgr: missing cdev-type property [ 1.438588] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 1.438595] DRAM derating cdev registered. [ 1.439635] vdd-fan: disabling [ 1.439638] vdd-usb-vbus: disabling [ 1.439640] vdd-usb-vbus2: disabling [ 1.439649] vddio-sdmmc-ap: disabling [ 1.439738] vdd-3v3-sd: disabling [ 1.439743] avdd-io-edp-1v05: disabling [ 1.439746] vdd-usb-hub-en: disabling [ 1.439835] ALSA device list: [ 1.439840] #0: tegra-hda at 0x70038000 irq 82 [ 1.439843] #1: tegra-snd-t210ref-mobile-rt565x [ 1.442019] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 1.442931] Freeing unused kernel memory: 8576K [ 1.462822] usb 1-2: New USB device found, idVendor=0424, idProduct=2744 [ 1.462828] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.462832] usb 1-2: Product: USB2744 [ 1.462835] usb 1-2: Manufacturer: Microchip Tech [ 1.463676] hub 1-2:1.0: USB hub found [ 1.463751] hub 1-2:1.0: 5 ports detected [ 1.464859] Root device found: mmcblk0p1 [ 1.465887] Found dev node: /dev/mmcblk0p1 [ 1.742919] EXT4-fs (mmcblk0p1): 19 orphan inodes deleted [ 1.742923] EXT4-fs (mmcblk0p1): recovery complete [ 1.750002] usb 1-2.1: new low-speed USB device number 3 using tegra-xusb [ 1.765025] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 1.765789] Rootfs mounted over mmcblk0p1 [ 1.777971] usb 1-2.1: New USB device found, idVendor=413c, idProduct=2113 [ 1.777997] usb 1-2.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 1.778001] usb 1-2.1: Product: Dell KB216 Wired Keyboard [ 1.779599] Switching from initrd to actual rootfs [ 1.782543] input: Dell KB216 Wired Keyboard as /devices/70090000.xusb/usb1/1-2/1-2.1/1-2.1:1.0/0003:413C:2113.0001/input/input2 [ 1.838117] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.842402] hid-generic 0003:413C:2113.0001: input,hidraw0: USB HID v1.11 Keyboard [Dell KB216 Wired Keyboard] on usb-70090000.xusb-2.1/input0 [ 1.847921] input: Dell KB216 Wired Keyboard as /devices/70090000.xusb/usb1/1-2/1-2.1/1-2.1:1.1/0003:413C:2113.0002/input/input3 [ 1.882085] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.893133] cgroup: cgroup2: unknown option "nsdelegate" [ 1.906183] hid-generic 0003:413C:2113.0002: input,hidraw1: USB HID v1.11 Device [Dell KB216 Wired Keyboard] on usb-70090000.xusb-2.1/input1 [ 1.908414] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 1.909167] systemd[1]: Detected architecture arm64. [ 1.932479] systemd[1]: Set hostname to . [ 1.990023] usb 1-2.2: new low-speed USB device number 4 using tegra-xusb [ 1.992867] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 1.992876] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 2.018564] usb 1-2.2: New USB device found, idVendor=413c, idProduct=301a [ 2.018569] usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.018572] usb 1-2.2: Product: Dell MS116 USB Optical Mouse [ 2.018576] usb 1-2.2: Manufacturer: PixArt [ 2.021319] input: PixArt Dell MS116 USB Optical Mouse as /devices/70090000.xusb/usb1/1-2/1-2.2/1-2.2:1.0/0003:413C:301A.0003/input/input4 [ 2.021581] hid-generic 0003:413C:301A.0003: input,hidraw2: USB HID v1.11 Mouse [PixArt Dell MS116 USB Optical Mouse] on usb-70090000.xusb-2.2/input0 [ 2.038008] tegra_cec 70015000.tegra_cec: physical address: 10:00. [ 2.093506] random: systemd: uninitialized urandom read (16 bytes read) [ 2.095271] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 2.095376] random: systemd: uninitialized urandom read (16 bytes read) [ 2.095396] systemd[1]: Reached target Swap. [ 2.095462] random: systemd: uninitialized urandom read (16 bytes read) [ 2.096963] systemd[1]: Created slice System Slice. [ 2.097164] systemd[1]: Listening on fsck to fsckd communication Socket. [ 2.097334] systemd[1]: Listening on Journal Socket (/dev/log). [ 2.098007] usb 1-2.5: new high-speed USB device number 5 using tegra-xusb [ 2.102532] tegra_cec 70015000.tegra_cec: Sent res: -113. [ 2.102537] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 2.119652] usb 1-2.5: New USB device found, idVendor=0424, idProduct=2740 [ 2.119659] usb 1-2.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.119663] usb 1-2.5: Product: Hub Controller [ 2.119666] usb 1-2.5: Manufacturer: Microchip Tech [ 2.143157] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 2.242013] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.244046] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.267648] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [ 2.317719] systemd-journald[1966]: Received request to flush runtime journal from PID 1 [ 2.349395] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.349402] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.349407] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.349411] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.349415] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.349438] pci 0000:00:02.0: [10de:0faf] type 01 class 0x060400 [ 2.349500] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.349687] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.349809] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 2.349834] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.349864] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit pref] [ 2.349885] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.350044] pci 0000:01:00.0: supports D1 D2 [ 2.350048] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.362075] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.362110] pci 0000:00:02.0: BAR 15: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 2.362115] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.362123] pci 0000:01:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [ 2.362141] pci 0000:01:00.0: BAR 2: assigned [mem 0x20004000-0x20004fff 64bit pref] [ 2.362158] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.362166] pci 0000:00:02.0: PCI bridge to [bus 01] [ 2.362170] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.362177] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [ 2.362438] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 2.362442] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.362447] pcie_pme 0000:00:02.0:pcie001: service driver pcie_pme loaded [ 2.362536] aer 0000:00:02.0:pcie002: service driver aer loaded [ 2.362718] r8168 0000:01:00.0: enabling device (0000 -> 0003) [ 2.362737] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 2.386032] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 2.386124] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e9:f3:49 from device tree [ 2.386835] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 2.386853] r8168 Copyright (C) 2017 Realtek NIC software team This program comes with ABSOLUTELY NO WARRANTY; for details, please see . This is free software, and you are welcome to redistribute it under certain conditions; see . [ 3.102747] using random self ethernet address [ 3.123202] using random host ethernet address [ 3.376513] random: crng init done [ 3.379947] random: 7 urandom warning(s) missed due to ratelimiting [ 3.661619] Mass Storage Function, version: 2009/09/11 [ 3.661626] LUN: removable file: (no medium) [ 3.667144] using random self ethernet address [ 3.673674] using random host ethernet address [ 3.760828] rndis0: HOST MAC be:3a:80:19:c8:b4 [ 3.761059] rndis0: MAC be:3a:80:19:c8:b5 [ 3.766444] usb0: HOST MAC be:3a:80:19:c8:b6 [ 3.766680] usb0: MAC be:3a:80:19:c8:b7 [ 3.766704] tegra-xudc-new 700d0000.xudc: exiting ELPG [ 3.768432] tegra-xudc-new 700d0000.xudc: exiting ELPG done [ 3.768451] tegra-xudc-new 700d0000.xudc: ep 0 (type: 0, dir: out) enabled [ 3.768619] tegra-xudc-new 700d0000.xudc: entering ELPG [ 3.768866] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 3.768886] tegra-xudc-new 700d0000.xudc: exiting ELPG [ 3.772993] tegra-xudc-new 700d0000.xudc: exiting ELPG done [ 3.773017] tegra-xudc-new 700d0000.xudc: entering ELPG [ 3.773265] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 3.779459] l4tbr0: port 1(rndis0) entered blocking state [ 3.779464] l4tbr0: port 1(rndis0) entered disabled state [ 3.782613] device rndis0 entered promiscuous mode [ 3.798419] IPv6: ADDRCONF(NETDEV_UP): rndis0: link is not ready [ 3.813005] l4tbr0: port 2(usb0) entered blocking state [ 3.813010] l4tbr0: port 2(usb0) entered disabled state [ 3.815158] device usb0 entered promiscuous mode [ 3.846130] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 4.068634] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.069775] eth0: 0xffffff800d585000, 00:04:4b:e9:f3:49, IRQ 407 [ 4.074257] zram: Added device: zram0 [ 4.078942] zram: Added device: zram1 [ 4.079495] zram: Added device: zram2 [ 4.080482] zram: Added device: zram3 [ 4.134430] zram0: detected capacity change from 0 to 518574080 [ 4.225554] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.269957] Adding 506416k swap on /dev/zram0. Priority:5 extents:1 across:506416k SS [ 4.277237] zram1: detected capacity change from 0 to 518574080 [ 4.293755] Adding 506416k swap on /dev/zram1. Priority:5 extents:1 across:506416k SS [ 4.302253] zram2: detected capacity change from 0 to 518574080 [ 4.313169] Adding 506416k swap on /dev/zram2. Priority:5 extents:1 across:506416k SS [ 4.327721] zram3: detected capacity change from 0 to 518574080 [ 4.343889] Adding 506416k swap on /dev/zram3. Priority:5 extents:1 across:506416k SS [ 4.910118] mmc1: Data CRC error [ 4.913348] sdhci: =========== REGISTER DUMP (mmc1)=========== [ 4.919171] sdhci: Sys addr: 0x00000080 | Version: 0x00000303 [ 4.924991] sdhci: Blk size: 0x00007200 | Blk cnt: 0x00000076 [ 4.930811] sdhci: Argument: 0x00000820 | Trn mode: 0x0000003b [ 4.936631] sdhci: Present: 0x01fb0000 | Host ctl: 0x00000013 [ 4.942452] sdhci: Power: 0x00000001 | Blk gap: 0x00000000 [ 4.948272] sdhci: Wake-up: 0x00000000 | Clock: 0x00000007 [ 4.954093] sdhci: Timeout: 0x0000000e | Int stat: 0x00000000 [ 4.959913] sdhci: Int enab: 0x02ff100b | Sig enab: 0x02fc100b [ 4.965732] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 [ 4.971551] sdhci: Caps: 0x376cd08c | Caps_1: 0x10006f77 [ 4.977370] sdhci: Cmd: 0x0000123a | Max curr: 0x00000000 [ 4.983188] sdhci: Host ctl2: 0x00003000 [ 4.987102] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000ffefe410 [ 4.993636] sdhci: =========================================== [ 4.999681] mmcblk1: error -110 sending stop command, original cmd response 0x900, card status 0x400900 [ 4.999687] mmcblk1: error -84 transferring data, sector 2080, nr 128, cmd response 0x900, card status 0x0 [ 5.280936] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 5.280943] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 5.287531] tegradc tegradc.0: blank - powerdown [ 5.349749] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 5.349752] Extcon AUX1(HDMI) disable [ 5.371848] tegradc tegradc.0: unblank [ 5.383719] tegradc tegradc.0: nominal-pclk:148500000 parent:148500000 div:1.0 pclk:148500000 147015000~161865000 [ 5.383799] tegradc tegradc.0: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_75m_150m [ 5.384882] tegradc tegradc.0: hdmi: get RGB quant from EDID. [ 5.384889] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 5.419609] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 5.419612] Extcon AUX1(HDMI) enable [ 5.429375] tegradc tegradc.0: unblank [ 5.429391] tegradc tegradc.1: blank - powerdown [ 5.606326] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 5.626695] usb 2-1: New USB device found, idVendor=0424, idProduct=5744 [ 5.626702] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=0 [ 5.626706] usb 2-1: Product: USB5744 [ 5.626709] usb 2-1: Manufacturer: Microchip Tech [ 5.627597] hub 2-1:1.0: USB hub found [ 5.627675] hub 2-1:1.0: 4 ports detected [ 5.778029] usb 2-1: usb_suspend_both: status 0 [ 5.778202] usb usb2: usb_suspend_both: status 0 [ 7.286784] r8168: eth0: link up [ 7.286843] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.401641] fuse init (API version 7.26) [ 8.475325] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 8.475337] Bluetooth: BNEP socket layer initialized [ 9.353261] tegradc tegradc.0: unblank [ 9.353271] tegradc tegradc.1: blank - powerdown [ 12.144970] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null)