[0000.260] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.265] Processing in cold boot mode Bootloader 2
[0000.270] A02 Bootrom Patch rev = 1023
[0000.274] Power-up reason: pmc por
[0000.277] No Battery Present
[0000.279] pmic max77620 reset reason
[0000.283] pmic max77620 NVERC : 0x80
[0000.286] RamCode = 0
[0000.288] Platform has DDR4 type RAM
[0000.292] max77620 disabling SD1 Remote Sense
[0000.296] Setting DDR voltage to 1125mv
[0000.300] Serial Number of Pmic Max77663: 0xe05a4
[0000.307] Entering ramdump check
[0000.310] Get RamDumpCarveOut = 0x0
[0000.314] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.319] Last reboot was clean, booting normally!
[0000.323] Sdram initialization is successful 
[0000.328] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.334] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.339] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.345] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.351] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.357] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.363] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.369] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.385] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.391] Platform-DebugCarveout: 0
[0000.394] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.400] Non secure mode, and RB not enabled.
[0000.417] Csd NumOfBlocks=0
[0000.611] *** Booting BFS0.
[0000.614] Read PT from (0:3)
[0000.620] Using BFS PT to query partitions 
[0000.624] PT: Partition LNX NOT found ! 
[0001.224] *** Booting KFS0.
[0001.226] BoardID = 3448, SKU = 0x2
[0001.230] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.235] Read GPT from (0:3)
[0001.243] Using GPT Primary to query partitions
[0001.248] Loading Tboot-CPU binary
[0001.255] Verifying TBC in OdmNonSecureSBK mode
[0001.265] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0001.272] Bootloader downloaded successfully.
[0001.276] Downloaded Tboot-CPU binary to 0xa0000258
[0001.281] MAX77620_GPIO5 configured
[0001.284] CPU power rail is up
[0001.287] CPU clock enabled
[0001.291] Performing RAM repair
[0001.294] Updating A64 Warmreset Address to 0xa00002e9
[0001.299] BoardID = 3448, SKU = 0x2
[0001.302] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.308] Loading NvTbootBootloaderDTB
[0001.325] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0001.397] Bootloader DTB Load Address: 0x83000000
[0001.402] BoardID = 3448, SKU = 0x2
[0001.405] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.411] Loading NvTbootKernelDTB
[0001.427] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0001.499] Kernel DTB Load Address: 0x83100000
[0001.503] BoardID = 3448, SKU = 0x2
[0001.506] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.513] Loading cboot binary
[0001.525] Verifying EBT in OdmNonSecureSBK mode
[0001.566] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0001.573] Bootloader downloaded successfully.
[0001.578] BoardID = 3448, SKU = 0x2
[0001.581] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.587] PT: Partition NCT NOT found ! 
[0001.591] Warning: Find Partition via PT Failed
[0001.595] Next binary entry address: 0x92c00258 
[0001.600] BoardId: 3448
[0001.604] Overriding pmu board id with proc board id
[0001.609] Display board id is not available 
[0001.613] BoardID = 3448, SKU = 0x2
[0001.617] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.630] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.686] /bpmp deleted
[0001.688] SC7EntryFw header found loaded at 0xff700000
[0001.887] OVR2 PMIC
[0001.889] Bpmp FW successfully loaded
[0001.893] BoardID = 3448, SKU = 0x2
[0001.896] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.903] WB0 init successfully at 0xff780000
[0001.907] Set NvDecSticky Bits
[0001.911] GSC2 address ff53fffc value c0edbbcc
[0001.917] GSC MC Settings done
[0001.920] BoardID = 3448, SKU = 0x2
[0001.923] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.930] TOS Image length 53680
[0001.933]  Monitor size 53680
[0001.936]  OS size 0
[0001.941] Secure Os AES-CMAC Verification Success!
[0001.946] TOS image cipher info: plaintext
[0001.950] Loading and Validation of Secure OS Successful
[0001.966] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.970] NvTbootPackSdramParams: start. 
[0001.975] NvTbootPackSdramParams: done. 
[0001.979] Tegraboot started after 190275 us
[0001.983] Basic modules init took 1471959 us
[0001.987] Sec Bootdevice Read Time = 558 ms, Read Size = 14649 KB
[0001.993] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.999] Next stage binary read took 7376 us
[0002.003] Carveout took -28683 us
[0002.006] CPU initialization took 386177 us
[0002.010] Total time taken by TegraBoot 1836829 us

[0002.015] Starting CPU & Halting co-processor 

64NOTICE:  BL31: v1.3(release):5b49e7f80
NOTICE:  BL31: Built : 08:37:40, Feb 19 2021
ERROR:   Error initializing runtime service trusty_fast
[0002.137] RamCode = 0
[0002.142] LPDDR4 Training: Read DT: Number of tables = 2
[0002.147] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0002.160] EMC Training Successful
[0002.163] 408000 not found in DVFS table
[0002.169] RamCode = 0
[0002.173] DT Write: emc-table@204000 succeeded
[0002.178] DT Write: emc-table@1600000 succeeded
[0002.182] LPDDR4 Training: Write DT: Number of tables = 2
[0002.244] 
[0002.245] Debug Init done
[0002.247] Marked DTB cacheable
[0002.250] Bootloader DTB loaded at 0x83000000
[0002.255] Marked DTB cacheable
[0002.258] Kernel DTB loaded at 0x83100000
[0002.262] DeviceTree Init done
[0002.275] Pinmux applied successfully
[0002.279] gicd_base: 0x50041000
[0002.283] gicc_base: 0x50042000
[0002.286] Interrupts Init done
[0002.290] Using base:0x60005090 & irq:208 for tick-timer
[0002.295] Using base:0x60005098 for delay-timer
[0002.300] platform_init_timer: DONE
[0002.303] Timer(tick) Init done
[0002.307] osc freq = 38400 khz
[0002.311] 
[0002.312] Welcome to L4T Cboot
[0002.315] 
[0002.316] Cboot Version: 00.00.2018.01-t210-39562017
[0002.321] calling constructors
[0002.324] initializing heap
[0002.326] initializing threads
[0002.329] initializing timers
[0002.332] creating bootstrap completion thread
[0002.337] top of bootstrap2()
[0002.339] CPU: ARM Cortex A57
[0002.342] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0002.347] initializing platform
[0002.401] Config for emmc ddr50 mode completed
[0002.405] sdmmc bdev is already initialized
[0002.409] Enable APE clock
[0002.412] Un-powergate APE partition
[0002.416] of_register: registering tegra_udc to of_hal
[0002.421] of_register: registering inv20628-driver to of_hal
[0002.426] of_register: registering ads1015-driver to of_hal
[0002.432] of_register: registering lp8557-bl-driver to of_hal
[0002.438] of_register: registering bq2419x_charger to of_hal
[0002.443] of_register: registering bq27441_fuel_gauge to of_hal
[0002.455] gpio framework initialized
[0002.458] of_register: registering tca9539_gpio to of_hal
[0002.464] of_register: registering tca9539_gpio to of_hal
[0002.469] of_register: registering i2c_bus_driver to of_hal
[0002.475] of_register: registering i2c_bus_driver to of_hal
[0002.480] of_register: registering i2c_bus_driver to of_hal
[0002.486] pmic framework initialized
[0002.489] of_register: registering max77620_pmic to of_hal
[0002.495] regulator framework initialized
[0002.499] of_register: registering tps65132_bl_driver to of_hal
[0002.505] initializing target
[0002.510] gpio_driver_register: register 'tegra_gpio_driver' driver
[0002.519] board ID = D78, board SKU = 2
[0002.525] fixed regulator driver initialized
[0002.543] initializing OF layer
[0002.546] NCK carveout not present
[0002.549] Skipping dts_overrides
[0002.553] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.570] I2C Bus Init done
[0002.573] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.583] I2C Bus Init done
[0002.586] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.596] I2C Bus Init done
[0002.599] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.610] I2C Bus Init done
[0002.612] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.623] I2C Bus Init done
[0002.625] of_children_init: Ops found for compatible string maxim,max77620
[0002.636] max77620_init using irq 118
[0002.641] register 'maxim,max77620' pmic
[0002.645] gpio_driver_register: register 'max77620-gpio' driver
[0002.651] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.662] I2C Bus Init done
[0002.665] NCK carveout not present
[0002.675] Find /i2c@7000c000's alias i2c0
[0002.679] get eeprom at 1-a0, size 256, type 0
[0002.688] Find /i2c@7000c500's alias i2c2
[0002.692] get eeprom at 3-a0, size 256, type 0
[0002.697] get eeprom at 3-ae, size 256, type 0
[0002.701] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.712] eeprom_init: EEPROM incompatible version found
[0002.718] pm_ids_update: eeprom init failed
[0002.722] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.752] pm_ids_update: The pm board id is 3448-0002-400
[0002.759] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0002.767] pm_ids_update: pm id update successful
[0002.772] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.777] I2C slave not started
[0002.780] I2C write failed
[0002.782] Writing offset failed
[0002.786] eeprom_init: EEPROM read failed
[0002.789] pm_ids_update: eeprom init failed
[0002.819] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.825] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.833] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.839] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.847] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3e:7c:29
[0002.854] Plugin Manager: Parse ODM data 0x000a4000
[0002.866] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0002.881] Find /i2c@7000c000's alias i2c0
[0002.885] get eeprom at 1-a0, size 256, type 0
[0002.894] Find /i2c@7000c500's alias i2c2
[0002.898] get eeprom at 3-a0, size 256, type 0
[0002.902] get eeprom at 3-ae, size 256, type 0
[0002.907] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.918] eeprom_init: EEPROM incompatible version found
[0002.923] pm_ids_update: eeprom init failed
[0002.927] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.957] pm_ids_update: The pm board id is 3448-0002-400
[0002.964] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0002.971] pm_ids_update: pm id update successful
[0002.975] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.981] I2C slave not started
[0002.984] I2C write failed
[0002.986] Writing offset failed
[0002.989] eeprom_init: EEPROM read failed
[0002.993] pm_ids_update: eeprom init failed
[0003.023] Add serial number:1421621004724 as DT property
[0003.031] Applying platform configs
[0003.037] platform-init is not present. Skipping
[0003.042] calling apps_init()
[0003.063] Found 17 GPT partitions in "sdmmc3_user"
[0003.068] Proceeding to Cold Boot
[0003.071] starting app android_boot_app
[0003.075] Device state: unlocked
[0003.078] display console init
[0003.086] could not find regulator
[0003.110] hdmi cable not connected
[0003.113] is_hdmi_needed: HDMI not connected, returning false
[0003.119] hdmi is not connected
[0003.[0003.125] DT entry for leds-pwm not found
122] sor0 is not supported
[0003.132] display_console_init: no valid display out_type
[0003.140] subnode volume_up is not found !
[0003.144] subnode back is not found !
[0003.147] subnode volume_down is not found !
[0003.152] subnode menu is not found !
[0003.155] Gpio keyboard init success
[0003.203] found decompressor handler: lz4-legacy
[0003.217] decompressing blob (type 1)...
[0003.283] display_resolution: No display init
[0003.288] Failed to retrieve display resolution
[0003.292] Could not load/initialize BMP blob...ignoring
[0003.342] decompressor handler not found
[0003.346] load_firmware_blob: Firmware blob loaded, entries=2
[0003.351] XUSB blob version 0 size 124416 @ 0x92cb328c
[0003.358] -------> se_aes_verify_sbk_clear: 747
[0003.362] se_aes_verify_sbk_clear: Error
[0003.366] SE operation failed
[0003.369] bl_battery_charging: connected to external power supply
[0003.378] display_console_ioctl: No display init
[0003.382] switch_backlight failed
[0003.392] device_query_partition_size: failed to open partition sdmmc3_user:MSC !
[0003.399] MSC Partition not found
[0003.409] device_query_partition_size: failed to open partition sdmmc3_user:USP !
[0003.416] USP partition read failed!
[0003.420] blob_init: blob-partition USP header read failed
[0003.425] android_boot Unable to update recovery partition
[0003.431] kfs_getpartname: name = LNX
[0003.434] Loading kernel from LNX
[0003.524] load kernel from storage
[0003.534] decompressor handler not found
[0003.568] Successfully loaded kernel and ramdisk images
[0003.573] board ID = D78, board SKU = 2
[0003.578] display_resolution: No display init
[0003.582] Failed to retrieve display resolution
[0003.587] bmp blob is not loaded and initialized
[0003.591] Failed to display boot-logo
[0003.595] NCK carveout not present
[0003.598] Skipping dts_overrides
[0003.601] NCK carveout not present
[0003.611] Find /i2c@7000c000's alias i2c0
[0003.615] get eeprom at 1-a0, size 256, type 0
[0003.624] Find /i2c@7000c500's alias i2c2
[0003.628] get eeprom at 3-a0, size 256, type 0
[0003.633] get eeprom at 3-ae, size 256, type 0
[0003.637] pm_ids_update: Updating 1,a0, size 256, type 0
[0003.649] eeprom_init: EEPROM incompatible version found
[0003.654] pm_ids_update: eeprom init failed
[0003.658] pm_ids_update: Updating 3,a0, size 256, type 0
[0003.688] pm_ids_update: The pm board id is 3448-0002-400
[0003.695] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0003.703] pm_ids_update: pm id update successful
[0003.708] pm_ids_update: Updating 3,ae, size 256, type 0
[0003.713] I2C slave not started
[0003.716] I2C write failed
[0003.719] Writing offset failed
[0003.722] eeprom_init: EEPROM read failed
[0003.726] pm_ids_update: eeprom init failed
[0003.756] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0003.761] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0003.769] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0003.775] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0003.784] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3e:7c:29
[0003.790] Plugin Manager: Parse ODM data 0x000a4000
[0003.802] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0003.810] Add serial number:1421621004724 as DT property
[0003.819] "bpmp" doesn't exist, creating 
[0003.825] Updated bpmp info to DTB
[0003.830] Updated initrd info to DTB
[0003.833] "proc-board" doesn't exist, creating 
[0003.839] Updated board info to DTB
[0003.842] "pmu-board" doesn't exist, creating 
[0003.848] Updated board info to DTB
[0003.852] "display-board" doesn't exist, creating 
[0003.858] Updated board info to DTB
[0003.861] "reset" doesn't exist, creating 
[0003.866] Updated reset info to DTB
[0003.869] display_console_ioctl: No display init
[0003.874] display_console_ioctl: No display init
[0003.878] display_console_ioctl: No display init
[0003.883] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 vid 
[0003.917] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 
[0003.923] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part 
[0003.939] Updated bootarg info to DTB
[0003.943] Adding uuid 00000001643146c11000000013fb8400 to DT
[0003.949] Adding eks info 0 to DT
[0003.954] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0003.960] Updated memory info to DTB
[0003.968] set vdd_core voltage to 1125 mv
[0003.972] setting 'vdd-core' regulator to 1125000 micro volts
[0003.978] Found secure-pmc; disable BPMP


U-Boot 2020.04-g6b630d64fd (Feb 19 2021 - 08:37:46 -0800)

SoC: tegra210
Model: NVIDIA Jetson Nano Developer Kit
Board: NVIDIA P3450-0000
DRAM:  4 GiB
MMC:   sdhci@700b0000: 1, sdhci@700b0600: 0
Loading Environment from SPI Flash... unrecognized JEDEC id bytes: 00, 00, 00
*** Warning - spi_flash_probe_bus_cs() failed, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
MMC: no card present
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
879 bytes read in 22 ms (38.1 KiB/s)
1:      primary kernel
Retrieving file: /boot/initrd
7159841 bytes read in 179 ms (38.1 MiB/s)
Retrieving file: /boot/Image
34338824 bytes read in 777 ms (42.1 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb n 
## Flattened Device Tree blob at 83100000
   Booting using the fdt blob at 0x83100000
ERROR: reserving fdt memory region failed (addr=0 size=0)
ERROR: reserving fdt memory region failed (addr=0 size=0)
   Using Device Tree in place at 0000000083100000, end 000000008317d100
copying carveout for /host1x@50000000/dc@54200000...
copying carveout for /host1x@50000000/dc@54240000...

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-5294-d8000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb1
[    0.000000] Boot CPU: AArch64 Processor [411fd071]
[    0.000000] OF: fdt:memory scan node memory@80000000, reg size 32,
[    0.000000] OF: fdt: - 80000000 ,  7ee00000
[    0.000000] OF: fdt: - 100000000 ,  7f200000
[    0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '')
[    0.000000] bootconsole [uart8250] enabled                                                                        
[    0.384930] Node override does not have targer node                                                               
[    0.386870] Node override does not have targer node                                                               
[    0.387185] Node override does not have targer node                                                               
[    0.388330] Node override does not have targer node                                                               
[    0.388391] Node override does not have targer node                                                               
[    0.388447] Node override does not have targer node                                                               
[    1.088461] tegradc tegradc.1: dpd enable lookup fail:-19                                                         
[    1.594289] Host read timeout at address 545c00c4                                                                 
[    1.670549] qspi_mtd spi32766.0: unrecognized JEDEC id 000000                                                     
[    2.640016] cgroup: cgroup2: unknown option "nsdelegate"                                                          
[    3.856374] usb 1-2.4.1: Warning! Unlikely big volume range (=496), cval->res is probably wrong.                  
[    3.865379] usb 1-2.4.1: [51] FU [Mic Playback Volume] ch = 1, val = 0/7936/16                                    
[    3.882754] usb 1-2.4.1: Warning! Unlikely big volume range (=1008), cval->res is probably wrong.                 
[    3.893445] usb 1-2.4.1: [49] FU [Speaker Playback Volume] ch = 2, val = -16129/-1/16                             
[    3.900010] usb 1-2.4.1: Warning! Unlikely big volume range (=496), cval->res is probably wrong.                  
[    3.900015] usb 1-2.4.1: [50] FU [Mic Capture Volume] ch = 1, val = 0/7936/16                                     
[    4.031829] using random self ethernet address                                                                    
[    4.051212] using random host ethernet address                                                                    
[    4.366400] random: crng init done
[    4.369802] random: 7 urandom warning(s) missed due to ratelimiting
[    4.435451] scsi 0:0:0:0: Direct-Access     NORELSYS 1081             0    PQ: 0 ANSI: 6
[    4.448059] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    7.404043] usb 1-2.4.1: Warning! Unlikely big volume range (=496), cval->res is probably wrong.
[    7.413615] usb 1-2.4.1: [51] FU [Mic Playback Volume] ch = 1, val = 0/7936/16
[    7.427029] usb 1-2.4.1: Warning! Unlikely big volume range (=1008), cval->res is probably wrong.
[    7.436037] usb 1-2.4.1: [49] FU [Speaker Playback Volume] ch = 2, val = -16129/-1/16
[    7.450986] usb 1-2.4.1: Warning! Unlikely big volume range (=496), cval->res is probably wrong.
[    7.459878] usb 1-2.4.1: [50] FU [Mic Capture Volume] ch = 1, val = 0/7936/16