19/07/2021 12:05:38.012 [RX] - þ[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-39a9dc3d) [0000.131] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.139] Power-up reason: pmc por [0000.142] No Battery Present [0000.145] pmic max77620 reset reason [0000.148] pmic max77620 NVERC : 0x41 [0000.151] RamCode = 0 [0000.154] Platform has DDR4 type RAM [0000.157] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x121df8 [0000.173] Entering ramdump check [0000.176] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.189] Sdram initialization is successful [0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.320] Csd NumOfBlocks=61069312 [0000.325] Set High speed to 1 [0000.336] Using GPT Primary to query partitions [0000.340] Loading Tboot-CPU binary [0000.351] Verifying TBC in OdmNonSecureSBK mode [0000.361] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.368] Bootloader downloaded successfully. [0000.372] Downloaded Tboot-CPU binary to 0xa0000258 [0000.377] MAX77620_GPIO5 configured [0000.380] CPU power rail is up [0000.383] CPU clock enabled [0000.387] Performing RAM repair [0000.390] Updating A64 Warmreset Address to 0xa00002e9 [0000.395] Loading NvTbootBootloaderDTB [0000.421] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.494] Bootloader DTB Load Address: 0x83000000 [0000.498] Loading NvTbootKernelDTB [0000.524] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.596] Kernel DTB Load Address: 0x83100000 [0000.601] Loading cboot binary [0000.632] Verifying EBT in OdmNonSecureSBK mode [0000.674] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.681] Bootloader downloaded successfully. [0000.698] Using BFS PT to query partitions [0000.702] Next binary entry address: 0x92c00258 [0000.706] BoardId: 3448 [0000.711] Overriding pmu board id with proc board id [0000.716] Display board id is not available [0000.745] Verifying SC7EntryFw in OdmNonSecureSBK mode [0000.802] /bpmp deleted [0000.804] SC7EntryFw header found loaded at 0xff700000 [0000.999] OVR2 PMIC [0001.001] Bpmp FW successfully loaded [0001.005] WB0 init successfully at 0xff780000 [0001.009] Set NvDecSticky Bits [0001.013] GSC2 address ff53fffc value c0edbbcc [0001.019] GSC MC Settings done [0001.022] TOS Image length 53680 [0001.025] Monitor size 53680 [0001.028] OS size 0 [0001.037] Secure Os AES-CMAC Verification Success! [0001.041] TOS image cipher info: plaintext [0001.045] Loading and Validation of Secure OS Successful [0001.061] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.066] NvTbootPackSdramParams: start. [0001.071] NvTbootPackSdramParams: done. [0001.075] Tegraboot started after 52314 us [0001.078] Basic modules init took 685599 us [0001.082] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB [0001.088] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.093] Storage Device Read Time = 117 ms, Read Size = 2241 KB [0001.099] Storage Device Write Time = 0 ms, Write Size = 0 KB [0001.105] Next stage binary read took 25979 us [0001.109] Carveout took -37642 us [0001.112] CPU initialization took 374439 us [0001.116] Total time taken by TegraBoot 1048375 us [0001.121] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):de895fd9e NOTICE: BL31: Built : 12:23:48, Oct 16 2020 ERROR: Error initializing runtime service trusty_fast [0001.243] RamCode = 0 [0001.248] LPDDR4 Training: Read DT: Number of tables = 2 [0001.253] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.266] EMC Training Successful [0001.269] 408000 not found in DVFS table [0001.275] RamCode = 0 [0001.279] DT Write: emc-table@204000 succeeded [0001.284] DT Write: emc-table@1600000 succeeded [0001.288] LPDDR4 Training: Write DT: Number of tables = 2 [0001.328] [0001.329] Debug Init done [0001.332] Marked DTB cacheable [0001.335] Bootloader DTB loaded at 0x83000000 [0001.339] Marked DTB cacheable [0001.342] Kernel DTB loaded at 0x83100000 [0001.346] DeviceTree Init done [0001.359] Pinmux applied successfully [0001.363] gicd_base: 0x50041000 [0001.367] gicc_base: 0x50042000 [0001.370] Interrupts Init done [0001.374] Using base:0x60005090 & irq:208 for tick-timer [0001.379] Using base:0x60005098 for delay-timer [0001.384] platform_init_timer: DONE [0001.387] Timer(tick) Init done [0001.391] osc freq = 38400 khz [0001.395] [0001.396] Welcome to L4T Cboot [0001.399] [0001.400] Cboot Version: 00.00.2018.01-t210-4686ce50 [0001.405] calling constructors [0001.408] initializing heap [0001.411] initializing threads [0001.414] initializing timers [0001.416] creating bootstrap completion thread [0001.421] top of bootstrap2() [0001.424] CPU: ARM Cortex A57 [0001.426] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.431] initializing platform [0001.439] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.443] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.448] Macronix QSPI chip present [0001.451] SPI device register [0001.454] init boot device [0001.457] allocating memory for boot device(SPI) [0001.461] registering boot device [0001.481] sdmmc node status = okay [0001.484] sdcard instance = 0 [0001.487] sdcard gpio handle 0x5b [0001.490] sdcard gpio pin 0xc9 [0001.493] sdcard gpio flags 0x0 [0001.496] vmmc-supply 0x9e [0001.499] Instance: 0 [0001.501] Allocating memory for context [0001.505] enabling clock [0001.507] sd card init [0001.509] Check card present and stable [0001.513] Send command 0 [0001.529] Send command 3 [0001.534] Set RCA for the card [0001.537] Query card specific data by command 9 [0001.543] Parse CSD data [0001.545] Send command 7 [0001.556] Calling sd device register [0001.559] Init sdcard [0001.561] Allocating memory for boot device [0001.566] Registering user device [0001.579] Enable APE clock [0001.581] Un-powergate APE partition [0001.585] of_register: registering tegra_udc to of_hal [0001.590] of_register: registering inv20628-driver to of_hal [0001.596] of_register: registering ads1015-driver to of_hal [0001.601] of_register: registering lp8557-bl-driver to of_hal [0001.607] of_register: registering bq2419x_charger to of_hal [0001.613] of_register: registering bq27441_fuel_gauge to of_hal [0001.624] gpio framework initialized [0001.627] of_register: registering tca9539_gpio to of_hal [0001.633] of_register: registering tca9539_gpio to of_hal [0001.638] of_register: registering i2c_bus_driver to of_hal [0001.644] of_register: registering i2c_bus_driver to of_hal [0001.649] of_register: registering i2c_bus_driver to of_hal [0001.655] pmic framework initialized [0001.658] of_register: registering max77620_pmic to of_hal [0001.664] regulator framework initialized [0001.668] of_register: registering tps65132_bl_driver to of_hal [0001.674] initializing target [0001.680] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.688] board ID = D78, board SKU = 0 [0001.691] Skipping Z3! [0001.696] fixed regulator driver initialized [0001.714] initializing OF layer [0001.717] NCK carveout not present [0001.720] Skipping dts_overrides [0001.724] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.741] I2C Bus Init done [0001.744] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.754] I2C Bus Init done [0001.757] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.767] I2C Bus Init done [0001.770] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.780] I2C Bus Init done [0001.783] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.793] I2C Bus Init done [0001.796] of_children_init: Ops found for compatible string maxim,max77620 [0001.806] max77620_init using irq 118 [0001.811] register 'maxim,max77620' pmic [0001.816] gpio_driver_register: register 'max77620-gpio' driver [0001.822] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.832] I2C Bus Init done [0001.836] NCK carveout not present [0001.846] Find /i2c@7000c000's alias i2c0 [0001.849] get eeprom at 1-a0, size 256, type 0 [0001.858] Find /i2c@7000c500's alias i2c2 [0001.862] get eeprom at 3-a0, size 256, type 0 [0001.867] get eeprom at 3-ae, size 256, type 0 [0001.871] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.876] I2C slave not started [0001.879] I2C write failed [0001.882] Writing offset failed [0001.885] eeprom_init: EEPROM read failed [0001.889] pm_ids_update: eeprom init failed [0001.893] pm_ids_update: Updating 3,a0, size 256, type 0 [0001.923] pm_ids_update: The pm board id is 3448-0000-400 [0001.930] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0001.938] pm_ids_update: pm id update successful [0001.943] pm_ids_update: Updating 3,ae, size 256, type 0 [0001.973] pm_ids_update: The pm board id is 3449-0000-400 [0001.979] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0001.987] pm_ids_update: pm id update successful [0002.018] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.024] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.031] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.037] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.046] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:44:6a [0002.052] Plugin Manager: Parse ODM data 0x00094000 [0002.064] shim_cmdline_install: /chosen/bootargs: console=ttyS0,115200 console=tty0 fbcon=map:0 net.ifnames=0 [0002.081] Find /i2c@7000c000's alias i2c0 [0002.085] get eeprom at 1-a0, size 256, type 0 [0002.094] Find /i2c@7000c500's alias i2c2 [0002.098] get eeprom at 3-a0, size 256, type 0 [0002.102] get eeprom at 3-ae, size 256, type 0 [0002.107] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.112] I2C slave not started [0002.115] I2C write failed [0002.118] Writing offset failed [0002.121] eeprom_init: EEPROM read failed [0002.125] pm_ids_update: eeprom init failed [0002.129] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.159] pm_ids_update: The pm board id is 3448-0000-400 [0002.165] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.172] pm_ids_update: pm id update successful [0002.177] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.207] pm_ids_update: The pm board id is 3449-0000-400 [0002.213] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.220] pm_ids_update: pm id update successful [0002.250] Add serial number:1420121019773 as DT property [0002.258] Applying platform configs [0002.265] platform-init is not present. Skipping [0002.269] calling apps_init() [0002.295] Found 16 GPT partitions in "sd0" [0002.299] Proceeding to Cold Boot [0002.303] starting app android_boot_app [0002.306] Device state: unlocked [0002.309] display console init [0002.318] could not find regulator [0002.341] hdmi cable not connected [0002.344] is_hdmi_needDT entry for leds-pwm not found e[0002.353] d: HDMI not connected, returning false [0002.357] hdmi is not connected [0002.360] sor0 is not supported [0002.363] display_console_init: no valid display out_type [0002.372] subnode volume_up is not found ! [0002.375] subnode back is not found ! [0002.379] subnode volume_down is not found ! [0002.383] subnode menu is not found ! [0002.387] Gpio keyboard init success [0002.404] blob_init: BMP partition does not have valid Blob [0002.410] load_bmp_blob: BMP blob initialization failed [0002.415] Could not load/initialize BMP blob...ignoring [0002.467] decompressor handler not found [0002.471] load_firmware_blob: Firmware blob loaded, entries=2 [0002.477] -------> se_aes_verify_sbk_clear: 747 [0002.481] se_aes_verify_sbk_clear: Error [0002.485] bl_battery_charging: connected to external power supply [0002.492] xusb is supported [0002.498] error while finding nvidia,portmap [0003.002] xusb blob version 0 size 124416 [0003.006] firmware size 124416 [0003.011] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0003.026] xhci0: 64 bytes context size, 32-bit DMA [0003.066] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.086] uhub0: on usbus0 [0003.736] uhub0: 9 ports with 9 removable, self powered [0004.736] failed to get HID devices [0004.740] failed to init xhci or no usb device attached [0004.747] display_console_ioctl: No display init [0004.752] switch_backlight failed [0004.758] device_query_partition_size: failed to open partition sd0:MSC ! [0004.764] MSC Partition not found [0004.771] device_query_partition_size: failed to open partition sd0:USP ! [0004.777] USP partition read failed! [0004.781] blob_init: blob-partition USP header read failed [0004.786] android_boot Unable to update recovery partition [0004.792] kfs_getpartname: name = LNX [0004.795] Loading kernel from LNX [0004.901] load kernel from storage [0004.912] decompressor handler not found [0004.974] Successfully loaded kernel and ramdisk images [0004.994] blob_init: BMP partition does not have valid Blob [0004.999] load_bmp_blob: BMP blob initialization failed [0005.005] bmp blob is not loaded and initialized [0005.009] Failed to display boot-logo [0005.013] NCK carveout not present [0005.016] Skipping dts_overrides [0005.019] NCK carveout not present [0005.029] Find /i2c@7000c000's alias i2c0 [0005.033] get eeprom at 1-a0, size 256, type 0 [0005.042] Find /i2c@7000c500's alias i2c2 [0005.046] get eeprom at 3-a0, size 256, type 0 [0005.050] get eeprom at 3-ae, size 256, type 0 [0005.054] pm_ids_update: Updating 1,a0, size 256, type 0 [0005.060] I2C slave not started [0005.063] I2C write failed [0005.065] Writing offset failed [0005.068] eeprom_init: EEPROM read failed [0005.072] pm_ids_update: eeprom init failed [0005.076] pm_ids_update: Updating 3,a0, size 256, type 0 [0005.107] pm_ids_update: The pm board id is 3448-0000-400 [0005.113] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0005.122] pm_ids_update: pm id update successful [0005.126] pm_ids_update: Updating 3,ae, size 256, type 0 [0005.157] pm_ids_update: The pm board id is 3449-0000-400 [0005.163] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0005.171] pm_ids_update: pm id update successful [0005.201] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.207] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0005.215] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.221] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0005.229] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:44:6a [0005.236] Plugin Manager: Parse ODM data 0x00094000 [0005.248] shim_cmdline_install: /chosen/bootargs: console=ttyS0,115200 console=tty0 fbcon=map:0 net.ifnames=0 [0005.258] Add serial number:1420121019773 as DT property [0005.267] "bpmp" doesn't exist, creating [0005.273] Updated bpmp info to DTB [0005.278] Updated initrd info to DTB [0005.281] "proc-board" doesn't exist, creating [0005.287] Updated board info to DTB [0005.291] "pmu-board" doesn't exist, creating [0005.297] Updated board info to DTB [0005.300] "display-board" doesn't exist, creating [0005.306] Updated board info to DTB [0005.309] "reset" doesn't exist, creating [0005.314] Updated reset info to DTB [0005.317] display_console_ioctl: No display init [0005.322] display_console_ioctl: No display init [0005.326] display_console_ioctl: No display init [0005.331] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 [0005.365] DTB cmdline: console=ttyS0,115200 console=tty0 fbcon=map:0 net.ifnames=0 [0005.373] Updated bootarg info to DTB [0005.377] Adding uuid 00000001645106451000000015058480 to DT [0005.383] Adding eks info 0 to DT [0005.388] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0005.394] Updated memory info to DTB [0005.402] set vdd_core voltage to 1075 mv [0005.406] setting 'vdd-core' regulator to 1075000 micro volts [0005.426] Found secure-pmc; disable BPMP U-Boot 2020.10 (Nov 07 2020 - 11:31:11 +0000) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Scanning mmc devices 0 1 2 Card did not respond to voltage select! Card did not respond to voltage select! Failed to load 'balena-image-flasher' 24 bytes read in 6 ms (3.9 KiB/s) Found resin image on mmc 1 Loading resinOS_uEnv.txt from mmc device 1 partition 0xC Failed to load 'resinOS_uEnv.txt' Loading extra_uEnv.txt from mmc device 1 partition 0xC 0 bytes read in 3 ms (0 Bytes/s) Import extra_uEnv.txt in environment Loading bootcount.env from mmc device 1 partition 0xC Failed to load 'bootcount.env' No bootcount.env file. Setting bootcount=0 in environment Card did not respond to voltage select! Scanning mmc devices 0 1 2 Card did not respond to voltage select! Failed to load 'balena-image-flasher' Found resin image on mmc 1 Loading resinOS_uEnv.txt from mmc device 1 partition 0xC Failed to load 'resinOS_uEnv.txt' Loading extra_uEnv.txt from mmc device 1 partition 0xC 0 bytes read in 3 ms (0 Bytes/s) Import extra_uEnv.txt in environment Loading bootcount.env from mmc device 1 partition 0xC Failed to load 'bootcount.env' No bootcount.env file. Setting bootcount=0 in environment switch to partitions #0, OK mmc1 is current device Scanning mmc 1:0xD... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 250 bytes read in 42 ms (4.9 KiB/s) info: found default FDT entry, look for custom_fdt_file environment variable info: Custom fdt file not defined. Look for default board fdt file info: fdt file now is /boot/tegra210-p3448-0000-p3449-0000-b00.dtb - 44 1: primary boot/Image Retrieving file: /boot/Image 40232968 bytes read in 2366 ms (16.2 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 console=ttyS0,115200 console=tty0 fbcon=map:0 net.ifnames=0 root=UUID=ba1eadef-1ef0-4643-989e-503943a6aec6 ro rootwait sdhci_tegra.en_boot_part_access=1 Retrieving file: /boot/tegra210-p3448-0000-p3449-0000-b00.dtb 241286 bytes read in 55 ms (4.2 MiB/s) ## Flattened Device Tree blob at 80000000 Booting using the fdt blob at 0x80000000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000080000000, end 000000008003de85 copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... DT property /psci/nvidia,system-lp0-disable missing in source; can't copy Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-l4t-r32.4 (oe-user@oe-host) (gcc version 9.3.0 (GCC) ) #1 SMP PREEMPT Tue Oct 27 20:38:55 UTC 2020 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefa4000 s61976 r8192 d32232 u102400 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 console=ttyS0,115200 console=tty0 fbcon=map:0 net.ifnames=0 root=UUID=ba1eadef-1ef0-4643-989e-503943a6aec6 ro rootwait sdhci_tegra.en_boot_part_access=1 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29680(90%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3569940K/4159488K available (14974K kernel code, 2874K rwdata, 9584K rodata, 11776K init, 597K bss, 114412K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f20000 ( 14976 KB) [ 0.000000] .rodata : 0xffffff8008f20000 - 0xffffff8009890000 ( 9664 KB) [ 0.000000] .init : 0xffffff8009890000 - 0xffffff800a410000 ( 11776 KB) [ 0.000000] .data : 0xffffff800a410000 - 0xffffff800a6de808 ( 2875 KB) [ 0.000000] .bss : 0xffffff800a6de808 - 0xffffff800a773d2c ( 598 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.001523] Console: colour dummy device 80x25 [ 0.002510] console [tty0] enabled [ 0.002552] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.002586] pid_max: default: 32768 minimum: 301 [ 0.003042] Security Framework initialized [ 0.003276] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003301] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.004496] ftrace: allocating 46642 entries in 183 pages [ 0.174075] ASID allocator initialised with 65536 entries [ 0.211889] tegra-id: chipid=22117. [ 0.211937] tegra-id: opt_subrevision=0. [ 0.211966] Tegra Speedo/IDDQ fuse revision 4 [ 0.211983] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.212001] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0 [ 0.212021] Tegra: CPU Speedo Value 2079, SoC Speedo Value 1973, GPU Speedo Value 2096 [ 0.212046] Tegra: CPU IDDQ Value 1900, SoC IDDQ Value 2160, GPU IDDQ Value 2675 [ 0.212084] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1 [ 0.212113] DTS File Name: /yocto/resin-board/build/tmp/work-shared/jetson-nano/kernel-source/arch/arm64/boot/dts/../../../../nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.212153] DTB Build time: Oct 27 2020 20:38:55 [ 0.261027] CPU1: Booted secondary processor [411fd071] [ 0.292915] CPU2: Booted secondary processor [411fd071] [ 0.324899] CPU3: Booted secondary processor [411fd071] [ 0.324990] Brought up 4 CPUs [ 0.325066] SMP: Total of 4 processors activated. [ 0.325087] CPU features: detected feature: 32-bit EL0 Support [ 0.325363] CPU: All CPU(s) started at EL2 [ 0.325395] alternatives: patching kernel code [ 0.333506] devtmpfs: initialized [ 0.369689] Initilizing CustomIPI irq domain [ 0.370067] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.370115] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.380512] pinctrl core: initialized pinctrl subsystem [ 0.381116] OS set in device tree is not L4T. [ 0.381427] regulator-dummy: no parameters [ 0.381660] Initializing plugin-manager [ 0.381809] Plugin module not found [ 0.382012] node /plugin-manager/fragement@0 match with board >=3448-0000-100 [ 0.382528] node /plugin-manager/fragment@1 match with board >=3448-0000-101 [ 0.383391] node /plugin-manager/fragement@6 match with odm-data enable-tegra-wdt [ 0.383786] node /plugin-manager/fragement@8 match with odm-data enable-tegra-wdt [ 0.384308] node /plugin-manager/fragement@10 match with board >=3448-0000-300 [ 0.386254] node /plugin-manager/fragement@13 match with board >=3448-0000-300 [ 0.389889] NET: Registered protocol family 16 [ 0.391060] pstore: using zlib compression [ 0.391760] console [pstore-1] enabled [ 0.391779] pstore: Registered ramoops as persistent store backend [ 0.391801] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.401038] cpuidle: using governor menu [ 0.403814] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.405319] vdso: 2 pages (1 code @ ffffff8008f27000, 1 data @ ffffff800a414000) [ 0.405366] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.409381] atomic_pool_init():621: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.411652] Serial: AMBA PL011 UART driver [ 0.412136] tegra_powergate_init: DONE [ 0.412172] DTS File Name: /yocto/resin-board/build/tmp/work-shared/jetson-nano/kernel-source/arch/arm64/boot/dts/../../../../nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.412214] DTB Build time: Oct 27 2020 20:38:55 [ 0.413855] Tegra reboot handler registered. [ 0.418049] iommu: Adding device tegra-carveouts to group 0 [ 0.418221] platform tegra-carveouts: domain=ffffffc0f9b773d8 allocates as[0]=ffffffc0f9b880a8 [ 0.418571] iommu: Adding device smmu_test to group 1 [ 0.418635] platform smmu_test: domain=ffffffc0f9b77618 allocates as[0]=ffffffc0f9b88110 [ 0.419398] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.419474] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.419541] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.419568] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.419602] mc-err: mcerr ops are set to t21x [ 0.428904] iommu: Adding device 70090000.xusb to group 2 [ 0.429265] iommu: Adding device 70006000.serial to group 3 [ 0.429342] platform 70006000.serial: domain=ffffffc0f9bd7cd8 allocates as[0]=ffffffc0f9b88178 [ 0.429746] iommu: Adding device 70006040.serial to group 4 [ 0.429992] iommu: Adding device 70006200.serial to group 5 [ 0.430177] iommu: Adding device sound to group 6 [ 0.430243] platform sound: domain=ffffffc0f943f258 allocates as[0]=ffffffc0f9b881e0 [ 0.430759] iommu: Adding device 7000d400.spi to group 7 [ 0.431018] iommu: Adding device 7000d600.spi to group 8 [ 0.431299] iommu: Adding device 70410000.spi to group 9 [ 0.431592] iommu: Adding device 50000000.host1x to group 10 [ 0.431860] iommu: Adding device 54080000.vi to group 11 [ 0.432242] iommu: Adding device 54600000.isp to group 12 [ 0.432499] iommu: Adding device 54680000.isp to group 13 [ 0.432770] iommu: Adding device tegradc.0 to group 14 [ 0.432835] platform tegradc.0: domain=ffffffc0f944b198 allocates as[0]=ffffffc0f9b88248 [ 0.433407] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.433718] iommu: Adding device tegradc.1 to group 15 [ 0.433780] platform tegradc.1: domain=ffffffc0f944b3d8 allocates as[0]=ffffffc0f9b882b0 [ 0.434302] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.434562] iommu: Adding device 54340000.vic to group 16 [ 0.434765] iommu: Adding device 544c0000.nvenc to group 17 [ 0.434955] iommu: Adding device 54500000.tsec to group 18 [ 0.435153] iommu: Adding device 54100000.tsecb to group 19 [ 0.435351] iommu: Adding device 54480000.nvdec to group 20 [ 0.435541] iommu: Adding device 54380000.nvjpg to group 21 [ 0.436532] iommu: Adding device 546c0000.i2c to group 22 [ 0.436861] iommu: Adding device 57000000.gpu to group 23 [ 0.436926] platform 57000000.gpu: domain=ffffffc0f94553d8 allocates as[0]=ffffffc0f9b88318 [ 0.437007] platform 57000000.gpu: domain=ffffffc0f94553d8 allocates as[1]=ffffffc0f9b88380 [ 0.437104] platform 57000000.gpu: domain=ffffffc0f94553d8 allocates as[2]=ffffffc0f9b883e8 [ 0.437163] platform 57000000.gpu: domain=ffffffc0f94553d8 allocates as[3]=ffffffc0f9b88450 [ 0.437921] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.437965] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.437993] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [ 0.438015] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.438034] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.489201] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.489237] tegra-pmc: Clear bootloader IO dpd settings [ 0.489272] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.489351] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.489647] iommu: Adding device 70012000.se to group 24 [ 0.490368] iommu: Adding device 7000c000.i2c to group 25 [ 0.490629] iommu: Adding device 7000c400.i2c to group 26 [ 0.490876] iommu: Adding device 7000c500.i2c to group 27 [ 0.491131] iommu: Adding device 7000c700.i2c to group 28 [ 0.491390] iommu: Adding device 7000d000.i2c to group 29 [ 0.491644] iommu: Adding device 7000d100.i2c to group 30 [ 0.491933] iommu: Adding device sdhci-tegra.0 to group 31 [ 0.492006] platform sdhci-tegra.0: domain=ffffffc0f94dd558 allocates as[0]=ffffffc0f9b884b8 [ 0.492775] iommu: Adding device 700d0000.xudc to group 32 [ 0.495869] vdd-ac-bat: 5000 mV [ 0.496198] vdd-5v0-sys: 5000 mV [ 0.497054] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.497119] vdd-5v0-hdmi: 5000 mV [ 0.497497] vdd-1v8-sys: 1800 mV [ 0.497929] vdd-fan: supplied by vdd-5v0-sys [ 0.497981] vdd-fan: 5000 mV [ 0.498340] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.498385] vdd-usb-vbus: 5000 mV [ 0.498862] vdd-usb-vbus2: 5000 mV [ 0.521723] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.524161] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.525339] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.525381] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.525436] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.525761] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.533552] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.533855] SCSI subsystem initialized [ 0.534307] usbcore: registered new interface driver usbfs [ 0.534372] usbcore: registered new interface driver hub [ 0.534458] usbcore: registered new device driver usb [ 0.538102] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.544303] vdd-core: 600 <--> 1162 mV at 1075 mV [ 0.545271] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.548202] vdd-ddr-1v1: 1150 mV [ 0.548915] random: fast init done [ 0.552198] vdd-pre-reg-1v35: 1350 mV [ 0.556198] vdd-1v8: 1800 mV [ 0.560197] avdd-sys-1v2: 1200 mV [ 0.564198] vdd-pex-1v0: 1050 mV [ 0.564868] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.565416] max77620-ldo3: at 3100 mV [ 0.568204] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.568736] max77620-ldo5: at 3100 mV [ 0.572200] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [ 0.576200] avdd-1v05-pll: 1050 mV [ 0.580196] avdd-io-hdmi-dp: 1050 mV [ 0.582735] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.583048] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.583334] max77620 4-003c: max77620 probe successful [ 0.585765] media: Linux media interface: v0.10 [ 0.585830] Linux video capture interface: v2.00 [ 0.586633] pps_core: LinuxPPS API ver. 1 registered [ 0.586657] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.586694] PTP clock support registered [ 0.589721] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.590446] Advanced Linux Sound Architecture Driver Initialized. [ 0.591067] Bluetooth: Core ver 2.22 [ 0.591122] NET: Registered protocol family 31 [ 0.591141] Bluetooth: HCI device and connection manager initialized [ 0.591173] Bluetooth: HCI socket layer initialized [ 0.591198] Bluetooth: L2CAP socket layer initialized [ 0.591236] Bluetooth: SCO socket layer initialized [ 0.592940] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.592982] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.593046] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.593078] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.596344] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.597464] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.597575] vdd-3v3-sys: 3300 mV [ 0.597827] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.600275] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.600728] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.600785] vdd-3v3-sd: 3300 mV [ 0.601830] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.601886] avdd-io-edp-1v05: 1050 mV [ 0.602297] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.602355] vdd-usb-hub-en: 5000 mV [ 0.603506] camchar: rtcpu character device driver loaded [ 0.604086] extcon-gpio-states extcon:extcon@1: Cable state:1, cable id:1 [ 0.605249] clocksource: Switched to clocksource arch_sys_counter [ 0.640585] VFS: Disk quotas dquot_6.6.0 [ 0.640764] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.641300] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.641874] dma_declare_coherent_resizable_cma_memory:323: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.641923] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.642193] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.642222] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.642253] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.642306] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.642337] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.642375] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.642399] nvmap_page_pool_init: Total RAM pages: 1011269 [ 0.642421] nvmap_page_pool_init: nvmap page pool size: 126408 pages (493 MB) [ 0.642553] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.642884] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.643719] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.650947] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.651405] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.651775] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.652058] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.652250] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.652529] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.652551] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.652983] NET: Registered protocol family 2 [ 0.653966] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.654202] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.654680] TCP: Hash tables configured (established 32768 bind 32768) [ 0.654840] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.654940] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.655330] NET: Registered protocol family 1 [ 0.890704] Trying to unpack rootfs image as initramfs... [ 0.901129] host1x 50000000.host1x: initialized [ 0.902842] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.906681] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 0.916008] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.916558] 9p: Installing v9fs 9p2000 file system support [ 0.919898] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 0.920056] io scheduler noop registered [ 0.920339] io scheduler cfq registered (default) [ 0.922802] gic 702f9000.agic: GIC IRQ controller registered [ 0.925810] iommu: Adding device 702ef000.adsp to group 33 [ 0.934589] iommu: Adding device aconnect@702c0000:adsp_audio to group 34 [ 0.934745] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 0.935223] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x6187c0a [ 0.935258] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 0.936835] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 0.936952] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 0.937060] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 0.937349] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 0.937469] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 0.937578] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 0.937679] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 0.937788] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 0.937890] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 0.937995] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 0.943818] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 0.945402] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 0.947147] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 0.948429] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 0.948794] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 0.949680] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 0.949925] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 0.950221] Adding domain tsec-pd to PM domain host1x-pd [ 0.952572] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 0.953473] tsec 54500000.tsec: initialized [ 0.955072] tsec 54100000.tsecb: initialized [ 0.955740] Adding domain nvdec-pd to PM domain host1x-pd [ 0.959047] nvdec 54480000.nvdec: initialized [ 0.960051] Adding domain vic03-pd to PM domain host1x-pd [ 0.960256] Adding domain msenc-pd to PM domain host1x-pd [ 0.960439] Adding domain nvjpg-pd to PM domain host1x-pd [ 0.964343] falcon 54340000.vic: initialized [ 0.965644] falcon 544c0000.nvenc: initialized [ 0.967001] falcon 54380000.nvjpg: initialized [ 0.970955] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97 [ 0.971041] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 0.971092] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 0.971100] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 0.971188] display board info: id 0x0, fab 0x0 [ 0.971269] generic_infoframe_type: 0x87 [ 0.971376] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 0.971401] tegra_cec 70015000.tegra_cec: probed [ 0.971414] tegradc tegradc.0: DT parsed successfully [ 0.971451] tegradc tegradc.0: Display dc.ffffff800b100000 registered with id=0 [ 0.975097] tegradc tegradc.0: probed [ 0.975834] Console: switching to colour frame buffer device 80x30 [ 0.975882] tegradc tegradc.0: fb registered [ 0.977116] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 0.977217] tegradc tegradc.1: No lt-data, using default setting [ 0.977311] tegradc tegradc.1: No hpd-gpio in DT [ 0.977356] tegradc tegradc.1: DT parsed successfully [ 0.977415] tegradc tegradc.1: Display dc.ffffff800b280000 registered with id=1 [ 0.978799] tegradc tegradc.1: dpd enable lookup fail:-19 [ 0.978880] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.484835] Host read timeout at address 545c00c4 [ 1.485971] tegradc tegradc.1: probed [ 1.486352] tegradc tegradc.1: fb registered [ 1.486635] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.487318] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check disabled [ 1.487341] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.487606] kfuse 7000fc00.kfuse: initialized [ 1.488402] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.489296] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.489573] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 1.489594] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 1.489616] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 1.489641] tegradc tegradc.1: blank - powerdown [ 1.489670] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 1.489688] Extcon DP: HPD disabled [ 1.489700] hpd: hpd_switch 0 [ 1.489714] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 1.489733] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 1.489751] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 1.490241] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.490269] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.490640] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.491963] vdd-gpu: applied init 1000000uV constraint [ 1.491985] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.492328] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.495465] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.495588] No Device Node present for smmu client: serial8250 !! [ 1.495610] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.495670] iommu: Adding device serial8250 to group 35 [ 1.497678] console [ttyS0] disabled [ 1.497762] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.879292] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.005268] tegra_cec 70015000.tegra_cec: Can't find physical addresse. [ 2.005274] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 2.282852] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.687120] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.689137] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.795241] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.795250] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.795255] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.795260] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.795266] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.795631] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.805414] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [ 2.805420] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.805436] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit] [ 2.805456] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit] [ 2.805475] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.805487] pci 0000:00:02.0: PCI bridge to [bus 01] [ 2.805493] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.805500] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] [ 2.805850] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 2.805855] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 3.975202] console [ttyS0] enabled [ 3.979725] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 3.988897] serial-tegra 70006200.serial: RX in PIO mode [ 3.994319] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 4.004055] [drm] Initialized [ 4.017051] brd: module loaded [ 4.025654] loop: module loaded [ 4.029470] zram: Added device: zram0 [ 4.033156] tegra_profiler: version: 1.141, samples/io: 48/28 [ 4.039031] tegra_profiler: auth: init [ 4.044041] THERMAL EST: found 2 subdevs [ 4.048017] THERMAL EST num_resources: 0 [ 4.051954] [THERMAL EST subdev 0] [ 4.055371] [THERMAL EST subdev 1] [ 4.059216] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 4.068193] THERMAL EST: thz register success. [ 4.072841] THERMAL EST: end of probe, return err: 0 [ 4.078785] sd: No Scsi addr parsed to reserve index [ 4.083813] hisi_sas: driver version v1.6 [ 4.092630] tegra-qspi 70410000.spi: Prod settings list not found [ 4.099907] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes) [ 4.105346] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0 [ 4.119417] libphy: Fixed MDIO Bus: probed [ 4.124120] tun: Universal TUN/TAP device driver, 1.6 [ 4.129190] tun: (C) 1999-2004 Max Krasnyansky [ 4.136042] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 4.141892] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 4.147872] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 4.154839] igb: Copyright (c) 2007-2014 Intel Corporation. [ 4.160466] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 4.168303] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 4.174272] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 4.181240] Copyright(c) 1999 - 2017 Intel Corporation. [ 4.187337] r8168 0000:01:00.0: enabling device (0000 -> 0003) [ 4.193226] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 4.213591] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 4.225969] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:ec:44:6a from device tree [ 4.238456] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 4.249928] r8168 Copyright (C) 2017 Realtek NIC software team [ 4.249928] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 4.249928] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 4.281288] PPP generic driver version 2.4.2 [ 4.285781] PPP BSD Compression module registered [ 4.290523] PPP Deflate Compression module registered [ 4.295617] PPP MPPE Compression module registered [ 4.300421] NET: Registered protocol family 24 [ 4.305031] VFIO - User Level meta-driver version: 0.3 [ 4.312767] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.319369] ehci-pci: EHCI PCI platform driver [ 4.323886] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.330116] ohci-pci: OHCI PCI platform driver [ 4.334611] ohci-platform: OHCI generic platform driver [ 4.342601] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 4.349001] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 4.357382] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f971a000 id [ 4.365861] usbcore: registered new interface driver uas [ 4.371230] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release [ 4.371289] tegra-xusb 70090000.xusb: xHCI Host Controller [ 4.371315] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 4.372075] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 4.372139] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 4.372423] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.372428] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.372433] usb usb1: Product: xHCI Host Controller [ 4.372436] usb usb1: Manufacturer: Linux 4.9.140-l4t-r32.4 xhci-hcd [ 4.372441] usb usb1: SerialNumber: 70090000.xusb [ 4.382534] hub 1-0:1.0: USB hub found [ 4.382575] hub 1-0:1.0: 5 ports detected [ 4.383117] tegra-xusb 70090000.xusb: xHCI Host Controller [ 4.383129] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 4.383207] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.383305] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 4.383310] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.383314] usb usb2: Product: xHCI Host Controller [ 4.383318] usb usb2: Manufacturer: Linux 4.9.140-l4t-r32.4 xhci-hcd [ 4.383321] usb usb2: SerialNumber: 70090000.xusb [ 4.383732] hub 2-0:1.0: USB hub found [ 4.383765] hub 2-0:1.0: 4 ports detected [ 4.485396] usb usb1: usb_suspend_both: status 0 [ 4.511416] usbcore: registered new interface driver usb-storage [ 4.517553] usbcore: registered new interface driver usbserial [ 4.523426] usbcore: registered new interface driver usbserial_generic [ 4.529984] usbserial: USB Serial support registered for generic [ 4.539238] tegra-xudc-new 700d0000.xudc: device count: 1 [ 4.545935] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 4.552667] tegra-xudc-new 700d0000.xudc: vbus state: 1 [ 4.557911] tegra-xudc-new 700d0000.xudc: device mode on: 0 [ 4.563516] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0 [ 4.570244] tegra-xudc-new 700d0000.xudc: active: 0 => 1 [ 4.706554] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 4.716330] rtc rtc1: alarm rtc device [ 4.720125] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 4.727293] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 4.733925] i2c /dev entries driver [ 4.739019] i2c i2c-6: Added multiplexed i2c bus 7 [ 4.744171] i2c i2c-6: Added multiplexed i2c bus 8 [ 4.748981] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 4.756726] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [ 4.786004] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 4.792639] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 4.800157] imx219 7-0010: board setup failed [ 4.804630] imx219: probe of 7-0010 failed with error -121 [ 4.810628] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [ 4.839838] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 4.846457] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 4.853974] imx219 8-0010: board setup failed [ 4.858399] imx219: probe of 8-0010 failed with error -121 [ 4.864897] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 4.873967] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 4.881055] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 4.888435] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.897772] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 4.906740] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 4.915751] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.925069] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 4.934034] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 4.943054] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.952372] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 4.961336] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 4.969388] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 4.977314] tegra_aotag tegra-aotag: Registering sensor 0 [ 4.982823] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 4.988069] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 4.994490] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.003828] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 5.012033] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 5.020777] parse_throttle_dt_data: Num cap clks = 6 [ 5.025757] parse_throttle_dt_data: clk=cclk_g type=2 [ 5.030825] parse_throttle_dt_data: clk=gpu type=4 [ 5.035646] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 5.041765] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 5.047885] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 5.053896] parse_throttle_dt_data: clk=emc type=3 [ 5.059038] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.068454] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.077893] tegra_throttle_probe: probe successful. #cdevs=4 [ 5.084211] FAN dev name: pwm-fan [ 5.087614] FAN:gpio request success. [ 5.091363] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 5.097353] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 5.104178] pwm_fan_driver pwm-fan: fan tach request irq success [ 5.110212] pwm_fan_driver pwm-fan: tach period: 1000 [ 5.115371] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 5.122951] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 5.130700] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 5.138535] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 5.146370] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 5.154206] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 5.162040] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 5.169873] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 5.177708] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 5.185628] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 5.194668] device-mapper: uevent: version 1.0.3 [ 5.199808] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 5.213604] tegra210-cpufreq cpufreq: probe()...completed [ 5.219725] sdhci: Secure Digital Host Controller Interface driver [ 5.225909] sdhci: Copyright(c) Pierre Ossman [ 5.230264] sdhci-pltfm: SDHCI platform and OF driver helper [ 5.236372] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 5.241516] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 5.248771] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300 [ 5.259309] tegra-se 70012000.se: tegra_se_probe: complete [ 5.265297] hidraw: raw HID events driver (C) Jiri Kosina [ 5.271646] usbcore: registered new interface driver usbhid [ 5.277222] usbhid: USB HID core driver [ 5.283016] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 5.289756] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 5.299850] nvpmodel: initialized successfully [ 5.305357] usbcore: registered new interface driver snd-usb-audio [ 5.311630] No Device Node present for smmu client: snd-soc-dummy !! [ 5.318075] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 5.324025] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 5.335375] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 5.344959] iommu: Adding device snd-soc-dummy to group 36 [ 5.370936] OPE platform probe [ 5.374085] OPE platform probe successful [ 5.378363] OPE platform probe [ 5.381503] OPE platform probe successful [ 5.408982] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 5.414882] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 5.420752] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 5.426625] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 5.432507] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 5.438369] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 5.444233] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 5.450115] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 5.455978] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 5.461843] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 5.479503] u32 classifier [ 5.482232] Actions configured [ 5.485819] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 5.492070] IPVS: Registered protocols (TCP, UDP) [ 5.496846] IPVS: Connection hash table configured (size=4096, memory=64Kbytes) [ 5.504198] IPVS: Creating netns size=1920 id=0 [ 5.510327] IPVS: ipvs loaded. [ 5.514148] ip_tables: (C) 2000-2006 Netfilter Core Team [ 5.519523] Initializing XFRM netlink socket [ 5.524629] NET: Registered protocol family 10 [ 5.530056] NET: Registered protocol family 17 [ 5.534523] NET: Registered protocol family 15 [ 5.539058] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 5.546845] mmc0: hw tuning done ... [ 5.546879] mmc0: new ultra high speed SDR104 SDHC card at address 0001 [ 5.547392] mmcblk0: mmc0:0001 00000 29.1 GiB [ 5.552431] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 [ 5.573832] Bluetooth: RFCOMM socket layer initialized [ 5.578992] Bluetooth: RFCOMM ver 1.11 [ 5.582759] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 5.588686] Bluetooth: HIDP socket layer initialized [ 5.593674] 9pnet: Installing 9P2000 support [ 5.597981] Key type dns_resolver registered [ 5.602631] Registered cp15_barrier emulation handler [ 5.607745] Registered setend emulation handler [ 5.613984] registered taskstats version 1 [ 5.618753] Adding domain ve2-pd to PM domain host1x-pd [ 5.624263] Adding domain ve-pd to PM domain host1x-pd [ 5.631799] isp 54600000.isp: initialized [ 5.637011] isp 54680000.isp: initialized [ 5.653404] last reset is due to power on reset [ 5.657962] KERNEL: PMC reset status reg: 0x0 [ 5.662404] BL: PMC reset status reg: 0x0 [ 5.666422] BL: PMIC poweroff Event Recorder: 0x41 [ 5.672860] clk_cbus_recalc_rate: no gbus parent [ 5.677520] clk_cbus_round_rate: no gbus parent [ 5.682059] clk_cbus_round_rate: no gbus parent [ 5.686601] clk_cbus_recalc_rate: no gbus parent [ 5.691347] clk_cbus_recalc_rate: no gbus parent [ 5.695981] clk_cbus_round_rate: no gbus parent [ 5.700517] clk_cbus_round_rate: no gbus parent [ 5.705053] clk_cbus_recalc_rate: no gbus parent [ 5.709696] tegra_dvfs: GPU-cap: registered [ 5.713950] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 5.722650] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled [ 5.731440] tegra dvfs: vdd-gpu: nominal 1048mV, offset 708000uV, step 10000uV, scaling enabled [ 5.741864] tegra_dvfs: vdd-gpu-vts: registered [ 5.747168] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 5.757112] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 5.766612] input: gpio-keys as /devices/gpio-keys/input/input1 [ 5.805849] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:00:16 UTC (946688416) [ 5.815894] vi 54080000.vi: vi_probe: ++ [ 5.822887] vi 54080000.vi: initialized [ 5.828882] vi 54080000.vi: subdev nvcsi--2 bound [ 5.833756] vi 54080000.vi: subdev nvcsi--1 bound [ 5.838713] mmcblk mmc0:0001: Card claimed for testing. [ 5.844824] Disable partitions left on by BL [ 5.849113] disb [ 5.851190] bwmgr: missing cdev-type property [ 5.855662] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.864979] DRAM derating cdev registered. [ 5.870417] vdd-fan: disabling [ 5.873495] vdd-usb-vbus: disabling [ 5.876979] vdd-usb-vbus2: disabling [ 5.880568] vddio-sdmmc3-ap: disabling [ 5.884415] avdd-io-edp-1v05: disabling [ 5.888265] vdd-usb-hub-en: disabling [ 5.892031] ALSA device list: [ 5.895011] #0: tegra-hda at 0x70038000 irq 83 [ 5.899632] #1: tegra-snd-t210ref-mobile-rt565x [ 5.909574] Freeing unused kernel memory: 11776K [ 6.800307] zram0: detected capacity change from 0 to 2077110272 [ 8.061264] random: crng init done [ 8.543187] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 8.549072] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 8.646019] usb usb2: usb_suspend_both: status 0 [ 10.195332] EXT4-fs (mmcblk0p13): couldn't mount as ext3 due to feature incompatibilities [ 10.204152] EXT4-fs (mmcblk0p13): couldn't mount as ext2 due to feature incompatibilities [ 10.217669] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: (null) [ 10.253491] EXT4-fs (mmcblk0p15): mounted filesystem with ordered data mode. Opts: (null) [ 10.704707] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null) [ 10.982598] EXT4-fs (mmcblk0p16): recovery complete [ 10.988742] EXT4-fs (mmcblk0p16): mounted filesystem with ordered data mode. Opts: (null) [ 11.121361] tegra-xusb 70090000.xusb: entering ELPG [ 11.127340] tegra-pmc: PMC tegra_pmc_utmi_phy_enable_sleepwalk : port 1, speed 0 [ 11.135026] tegra-pmc: PMC tegra_pmc_utmi_phy_enable_sleepwalk : port 2, speed 0 [ 11.143466] tegra-xusb 70090000.xusb: entering ELPG done [ 11.287992] systemd[1]: System time before build time, advancing clock. [ 11.328940] cgroup: cgroup2: unknown option "nsdelegate" [ 11.655382] systemd[1]: /lib/systemd/system/balena-host.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/balena-host.sock → /run/balena-host.sock; please update the unit file accordingly. [ 11.687644] systemd[1]: /lib/systemd/system/balena-engine.socket:6: ListenStream= references a path below legacy directory /var/run/, updating /var/run/balena-engine.sock → /run/balena-engine.sock; please update the unit file accordingly. [ 12.193442] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1264 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [ 13.984813] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds. [ 13.994138] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 0) [ 14.333146] zram: Can't change algorithm for initialized device [ 15.878560] Adding 2028424k swap on /dev/zram0. Priority:-1 extents:1 across:2028424k SS [ 17.058827] IPv6: ADDRCONF(NETDEV_UP): resin-dns: link is not ready [ 18.435321] IPVS: Creating netns size=1920 id=1 [ 19.184090] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 19.200615] eth0: 0xffffff800a95e000, 00:04:4b:ec:44:6a, IRQ 406 [ 19.333060] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 19.900930] Bridge firewalling registered [ 20.554906] Netfilter messages via NETLINK v0.30. [ 20.565834] ctnetlink v0.93: registering with nfnetlink. [ 20.988153] IPv6: ADDRCONF(NETDEV_UP): supervisor0: link is not ready [ 21.494266] IPv6: ADDRCONF(NETDEV_UP): balena0: link is not ready [ 21.507565] IPVS: Creating netns size=1920 id=2 balenaOS 2.75.0 balena ttyS0 balena login:  _ _ ____ _____ | |__ __ _ | | ____ _ __ __ _ / __ \ / ____| | `_ \ / _` || | / __ \| `_ \ / _` | | | | |\____ \ | |_) | (_) || || ___/| | | || (_) | | |__| | ____) | |_.__/ \__,_||_| \____/|_| |_| \__,_| \____/ |_____/ ----------------------------------------------------- Booted - Check your balenaCloud dashboard. [ 25.540443] IPVS: Creating netns size=1920 id=3 [ 28.674280] ip6_tables: (C) 2000-2006 Netfilter Core Team