�[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x71 [0000.151] RamCode = 1 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x2723f2 [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff800000 Size=0x00000000 [0000.204] BpmpFw Carveout Base=0x00000000ff800000 Size=0x00000000 [0000.210] GSC1 Carveout Base=0x00000000ff800000 Size=0x00000000 [0000.216] Resize the SecureOs Carveout to 0x00100000 [0000.221] GSC2 Carveout Base=0x00000000ff900000 Size=0x00100000 [0000.227] GSC4 Carveout Base=0x00000000ff800000 Size=0x00000000 [0000.232] GSC5 Carveout Base=0x00000000ff800000 Size=0x00000000 [0000.238] GSC3 Carveout Base=0x00000000bf800000 Size=0x00200000 [0000.244] RamDump Carveout Base=0x0000000000000000 Size=0x00000000 [0000.250] Platform-DebugCarveout: 0 [0000.253] Nck Carveout Base=0x00000000ff800000 Size=0x00000000 [0000.259] Non secure mode, and RB not enabled. [0000.263] BoardID = 3448, SKU = 0x3 [0000.266] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.270] Nano-SD: checking PT table on QSPI ... [0000.274] Initialize FailControl [0000.277] Read PT from (2:0) [0000.308] PT crc32 and magic check passed. [0000.312] Using BFS PT to query partitions [0000.318] Loading Tboot-CPU binary [0000.346] Verifying TBC in OdmNonSecureSBK mode [0000.356] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.363] Bootloader downloaded successfully. [0000.367] Downloaded Tboot-CPU binary to 0xa0000258 [0000.372] MAX77620_GPIO5 configured [0000.375] CPU power rail is up [0000.378] CPU clock enabled [0000.382] Performing RAM repair [0000.385] Updating A64 Warmreset Address to 0xa00002e9 [0000.390] BoardID = 3448, SKU = 0x3 [0000.393] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.397] Nano-SD: checking PT table on QSPI ... [0000.401] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.407] Loading NvTbootBootloaderDTB [0000.474] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.543] Bootloader DTB Load Address: 0x83000000 [0000.548] BoardID = 3448, SKU = 0x3 [0000.551] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.555] Nano-SD: checking PT table on QSPI ... [0000.559] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.565] Loading NvTbootKernelDTB [0000.631] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.700] Kernel DTB Load Address: 0x83100000 [0000.704] BoardID = 3448, SKU = 0x3 [0000.708] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.711] Nano-SD: checking PT table on QSPI ... [0000.716] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.723] Loading cboot binary [0000.839] Verifying EBT in OdmNonSecureSBK mode [0000.881] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.888] Bootloader downloaded successfully. [0000.892] BoardID = 3448, SKU = 0x3 [0000.895] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.899] Nano-SD: checking PT table on QSPI ... [0000.904] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.910] PT: Partition NCT NOT found ! [0000.914] Warning: Find Partition via PT Failed [0000.918] Next binary entry address: 0x92c00258 [0000.922] BoardId: 3448 [0000.927] Overriding pmu board id with proc board id [0000.932] Display board id is not available [0000.936] No Bpmp FW loaded [0000.938] Not loading WB0 as no bpmp/sc7entry fw [0000.943] Set NvDecSticky Bits [0000.946] GSC2 address ff93fffc value c0edbbcc [0000.953] GSC MC Settings done [0000.956] BoardID = 3448, SKU = 0x3 [0000.959] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.963] Nano-SD: checking PT table on QSPI ... [0000.967] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.974] TOS Image length 53680 [0000.977] Monitor size 53680 [0000.980] OS size 0 [0000.995] Secure Os AES-CMAC Verification Success! [0001.000] TOS image cipher info: plaintext [0001.003] Loading and Validation of Secure OS Successful [0001.019] NvTbootPackSdramParams: start. [0001.024] NvTbootPackSdramParams: done. [0001.028] Tegraboot started after 51856 us [0001.032] Basic modules init took 954055 us [0001.036] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.042] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.047] Next stage binary read took 11286 us [0001.051] Carveout took -69913 us [0001.055] CPU initialization took 106084 us [0001.059] Total time taken by TegraBoot 1001512 us [0001.063] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:09:37, Jul 26 2021 ERROR: Error initializing runtime service trusty_fast [0001.185] RamCode = 1 [0001.190] LPDDR4 Training: Read DT: Number of tables = 2 [0001.195] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.207] EMC Training Successful [0001.210] 408000 not found in DVFS table [0001.217] RamCode = 1 [0001.220] DT Write: emc-table@204000 succeeded [0001.226] DT Write: emc-table@1600000 succeeded [0001.230] LPDDR4 Training: Write DT: Number of tables = 2 [0001.268] [0001.269] Debug Init done [0001.272] Marked DTB cacheable [0001.275] Bootloader DTB loaded at 0x83000000 [0001.280] Marked DTB cacheable [0001.283] Kernel DTB loaded at 0x83100000 [0001.287] DeviceTree Init done [0001.299] Pinmux applied successfully [0001.304] gicd_base: 0x50041000 [0001.307] gicc_base: 0x50042000 [0001.310] Interrupts Init done [0001.314] Using base:0x60005090 & irq:208 for tick-timer [0001.320] Using base:0x60005098 for delay-timer [0001.324] platform_init_timer: DONE [0001.328] Timer(tick) Init done [0001.331] osc freq = 38400 khz [0001.335] [0001.336] Welcome to L4T Cboot [0001.339] [0001.340] Cboot Version: 00.00.2018.01-t210-c952b4e6 [0001.345] calling constructors [0001.348] initializing heap [0001.351] initializing threads [0001.354] initializing timers [0001.357] creating bootstrap completion thread [0001.361] top of bootstrap2() [0001.364] CPU: ARM Cortex A57 [0001.367] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.372] initializing platform [0001.379] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.384] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.388] Macronix QSPI chip present [0001.392] SPI device register [0001.395] init boot device [0001.397] allocating memory for boot device(SPI) [0001.402] registering boot device [0001.410] QSPI bdev is already initialized [0001.414] Enable APE clock [0001.417] Un-powergate APE partition [0001.420] of_register: registering tegra_udc to of_hal [0001.425] of_register: registering inv20628-driver to of_hal [0001.431] of_register: registering ads1015-driver to of_hal [0001.436] of_register: registering lp8557-bl-driver to of_hal [0001.442] of_register: registering bq2419x_charger to of_hal [0001.448] of_register: registering bq27441_fuel_gauge to of_hal [0001.459] gpio framework initialized [0001.463] of_register: registering tca9539_gpio to of_hal [0001.468] of_register: registering tca9539_gpio to of_hal [0001.473] of_register: registering i2c_bus_driver to of_hal [0001.479] of_register: registering i2c_bus_driver to of_hal [0001.485] of_register: registering i2c_bus_driver to of_hal [0001.490] pmic framework initialized [0001.494] of_register: registering max77620_pmic to of_hal [0001.499] regulator framework initialized [0001.503] of_register: registering tps65132_bl_driver to of_hal [0001.509] initializing target [0001.515] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.523] board ID = D78, board SKU = 3 [0001.527] Skipping Z3! [0001.531] fixed regulator driver initialized [0001.550] initializing OF layer [0001.553] NCK carveout not present [0001.556] Skipping dts_overrides [0001.561] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.577] I2C Bus Init done [0001.579] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.590] I2C Bus Init done [0001.592] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.603] I2C Bus Init done [0001.605] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.615] I2C Bus Init done [0001.618] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.628] I2C Bus Init done [0001.631] of_children_init: Ops found for compatible string maxim,max77620 [0001.641] max77620_init using irq 118 [0001.646] register 'maxim,max77620' pmic [0001.650] gpio_driver_register: register 'max77620-gpio' driver [0001.657] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.667] I2C Bus Init done [0001.671] NCK carveout not present [0001.680] Find /i2c@7000c000's alias i2c0 [0001.684] get eeprom at 1-a0, size 256, type 0 [0001.693] Find /i2c@7000c500's alias i2c2 [0001.697] get eeprom at 3-a0, size 256, type 0 [0001.701] get eeprom at 3-ae, size 256, type 0 [0001.706] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.711] I2C slave not started [0001.714] I2C write failed [0001.717] Writing offset failed [0001.720] eeprom_init: EEPROM read failed [0001.724] pm_ids_update: eeprom init failed [0001.728] pm_ids_update: Updating 3,a0, size 256, type 0 [0001.758] pm_ids_update: The pm board id is 3448-0003-400 [0001.765] Adding plugin-manager/ids/3448-0003-400=/i2c@7000c500:module@0x50 [0001.773] pm_ids_update: pm id update successful [0001.777] pm_ids_update: Updating 3,ae, size 256, type 0 [0001.807] pm_ids_update: The pm board id is 3542-0000-201 [0001.814] Adding plugin-manager/ids/3542-0000-201=/i2c@7000c500:module@0x57 [0001.822] pm_ids_update: pm id update successful [0001.852] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0001.858] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0001.866] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0001.871] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0001.880] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:2e:f2:4a [0001.886] Plugin Manager: Parse ODM data 0x000a4000 [0001.898] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0001.913] Find /i2c@7000c000's alias i2c0 [0001.917] get eeprom at 1-a0, size 256, type 0 [0001.925] Find /i2c@7000c500's alias i2c2 [0001.929] get eeprom at 3-a0, size 256, type 0 [0001.934] get eeprom at 3-ae, size 256, type 0 [0001.938] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.943] I2C slave not started [0001.946] I2C write failed [0001.949] Writing offset failed [0001.952] eeprom_init: EEPROM read failed [0001.956] pm_ids_update: eeprom init failed [0001.960] pm_ids_update: Updating 3,a0, size 256, type 0 [0001.990] pm_ids_update: The pm board id is 3448-0003-400 [0001.996] Adding plugin-manager/ids/3448-0003-400=/i2c@7000c500:module@0x50 [0002.003] pm_ids_update: pm id update successful [0002.008] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.038] pm_ids_update: The pm board id is 3542-0000-201 [0002.044] Adding plugin-manager/ids/3542-0000-201=/i2c@7000c500:module@0x57 [0002.051] pm_ids_update: pm id update successful [0002.082] Add serial number:1424020008448 as DT property [0002.089] Applying platform configs [0002.095] platform-init is not present. Skipping [0002.100] calling apps_init() [0002.106] Couldn't find GPT header [0002.110] Proceeding to Cold Boot [0002.113] starting app android_boot_app [0002.117] Device state: unlocked [0002.120] display console init [0002.129] could not find regulator [0002.152] hdmi cable not connected [0002.155] is_hdmi_needed: HDMI not connected, returning false [0002.161] hdmi is not connected [0002.164] sor0 is not supporteDT entry for leds-pwm not found d[0002.173] [0002.174] display_console_init: no valid display out_type [0002.182] subnode volume_up is not found ! [0002.186] subnode back is not found ! [0002.189] subnode volume_down is not found ! [0002.194] subnode menu is not found ! [0002.197] Gpio keyboard init success [0002.278] found decompressor handler: lz4-legacy [0002.292] decompressing blob (type 1)... [0002.357] display_resolution: No display init [0002.361] Failed to retrieve display resolution [0002.366] Could not load/initialize BMP blob...ignoring [0002.442] decompressor handler not found [0002.446] load_firmware_blob: Firmware blob loaded, entries=2 [0002.452] XUSB blob version 0 size 126464 @ 0x92ca828c [0002.458] -------> se_aes_verify_sbk_clear: 747 [0002.462] se_aes_verify_sbk_clear: Error [0002.466] SE operation failed [0002.469] bl_battery_charging: connected to external power supply [0002.478] display_console_ioctl: No display init [0002.482] switch_backlight failed [0002.489] device_query_partition_size: failed to open partition spiflash0:MSC ! [0002.496] MSC Partition not found [0002.502] device_query_partition_size: failed to open partition spiflash0:USP ! [0002.509] USP partition read failed! [0002.513] blob_init: blob-partition USP header read failed [0002.518] android_boot Unable to update recovery partition [0002.524] kfs_getpartname: name = LNX [0002.527] Loading kernel from LNX [0002.537] Found 19 BFS partitions in "spiflash0" [0002.857] load kernel from storage [0002.862] decompressor handler not found [0003.128] Successfully loaded kernel and ramdisk images [0003.133] board ID = D78, board SKU = 3 [0003.138] sdmmc node status = okay [0003.141] sdcard instance = 0 [0003.144] sdmmc cd-inverted [0003.146] sdcard gpio handle 0x5a [0003.150] sdcard gpio pin 0xc9 [0003.153] sdcard gpio flags 0x0 [0003.156] vmmc-supply 0x9a [0003.158] cd_gpio_pin = 201 [0003.161] pin_state = 0 [0003.163] Found sdcard [0003.165] SD-card IS present ... [0003.169] load_and_boot_kernel: SD card detected OK [0003.174] display_resolution: No display init [0003.179] Failed to retrieve display resolution [0003.183] bmp blob is not loaded and initialized [0003.188] Failed to display boot-logo [0003.191] NCK carveout not present [0003.195] Skipping dts_overrides [0003.198] NCK carveout not present [0003.207] Find /i2c@7000c000's alias i2c0 [0003.211] get eeprom at 1-a0, size 256, type 0 [0003.220] Find /i2c@7000c500's alias i2c2 [0003.224] get eeprom at 3-a0, size 256, type 0 [0003.228] get eeprom at 3-ae, size 256, type 0 [0003.233] pm_ids_update: Updating 1,a0, size 256, type 0 [0003.238] I2C slave not started [0003.241] I2C write failed [0003.244] Writing offset failed [0003.247] eeprom_init: EEPROM read failed [0003.251] pm_ids_update: eeprom init failed [0003.255] pm_ids_update: Updating 3,a0, size 256, type 0 [0003.285] pm_ids_update: The pm board id is 3448-0003-400 [0003.292] Adding plugin-manager/ids/3448-0003-400=/i2c@7000c500:module@0x50 [0003.300] pm_ids_update: pm id update successful [0003.305] pm_ids_update: Updating 3,ae, size 256, type 0 [0003.335] pm_ids_update: The pm board id is 3542-0000-201 [0003.341] Adding plugin-manager/ids/3542-0000-201=/i2c@7000c500:module@0x57 [0003.349] pm_ids_update: pm id update successful [0003.379] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.385] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0003.393] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.399] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0003.407] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:2e:f2:4a [0003.413] Plugin Manager: Parse ODM data 0x000a4000 [0003.425] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0003.433] Add serial number:1424020008448 as DT property [0003.441] Updated bpmp info to DTB [0003.446] Updated initrd info to DTB [0003.449] "proc-board" doesn't exist, creating [0003.455] Updated board info to DTB [0003.459] "pmu-board" doesn't exist, creating [0003.465] Updated board info to DTB [0003.468] "display-board" doesn't exist, creating [0003.474] Updated board info to DTB [0003.477] "reset" doesn't exist, creating [0003.482] Updated reset info to DTB [0003.485] display_console_ioctl: No display init [0003.490] display_console_ioctl: No display init [0003.494] display_console_ioctl: No display init [0003.499] Cmdline: tegraid=21.1.2.0.0 ddr_die=2048M@2048M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 core_edp_mv=1075 core_edp_ma=4000 gpt [0003.531] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0003.537] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0003.549] Updated bootarg info to DTB [0003.553] Adding uuid 00000001644568050400000003000400 to DT [0003.559] Adding eks info 0 to DT [0003.564] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0003.570] Updated memory info to DTB [0003.578] set vdd_core voltage to 1075 mv [0003.582] setting 'vdd-core' regulator to 1075000 micro volts [0003.588] Found secure-pmc; disable BPMP U-Boot 2020.04-g46e4604c78 (Jul 26 2021 - 12:09:42 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano 2GB Developer Kit Board: NVIDIA P3541-0000 DRAM: 2 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 845 bytes read in 29 ms (28.3 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7160133 bytes read in 625 ms (10.9 MiB/s) Retrieving file: /boot/Image 34484232 bytes read in 2923 ms (11.3 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=2048M@2048M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 core_edp_mv=1075 core_edp_ma=4000 gpt earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317ae79 copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-tegra (buildbrain@mobile-u64-5496-d5000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Mon Jul 26 12:13:06 PDT 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 3f800000 [ 0.000000] OF: fdt: - bfa00000 , 3fe00000 [ 0.000000] OF: fdt: - ffa00000 , 600000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.269032] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.276670] imx219 6-0010: board setup failed