=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2021.06.25 14:20:19 =~=~=~=~=~=~=~=~=~=~=~= [0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x1425a9 [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.281] Read PT from (2:0) [0000.296] Using BFS PT to query partitions [0000.302] Loading Tboot-CPU binary [0000.330] Verifying TBC in OdmNonSecureSBK mode [0000.340] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.347] Bootloader downloaded successfully. [0000.351] Downloaded Tboot-CPU binary to 0xa0000258 [0000.356] MAX77620_GPIO5 configured [0000.359] CPU power rail is up [0000.362] CPU clock enabled [0000.366] Performing RAM repair [0000.369] Updating A64 Warmreset Address to 0xa00002e9 [0000.374] BoardID = 3448, SKU = 0x0 [0000.377] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.381] Nano-SD: checking PT table on QSPI ... [0000.385] Loading NvTbootBootloaderDTB [0000.452] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.525] Bootloader DTB Load Address: 0x83000000 [0000.530] BoardID = 3448, SKU = 0x0 [0000.533] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.537] Nano-SD: checking PT table on QSPI ... [0000.541] Loading NvTbootKernelDTB [0000.607] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.680] Kernel DTB Load Address: 0x83100000 [0000.684] BoardID = 3448, SKU = 0x0 [0000.688] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.692] Nano-SD: checking PT table on QSPI ... [0000.698] Loading cboot binary [0000.814] Verifying EBT in OdmNonSecureSBK mode [0000.855] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.862] Bootloader downloaded successfully. [0000.866] BoardID = 3448, SKU = 0x0 [0000.870] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.873] Nano-SD: checking PT table on QSPI ... [0000.878] PT: Partition NCT NOT found ! [0000.882] Warning: Find Partition via PT Failed [0000.886] Next binary entry address: 0x92c00258 [0000.891] BoardId: 3448 [0000.895] Overriding pmu board id with proc board id [0000.900] Display board id is not available [0000.904] BoardID = 3448, SKU = 0x0 [0000.907] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.911] Nano-SD: checking PT table on QSPI ... [0001.016] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.073] /bpmp deleted [0001.075] SC7EntryFw header found loaded at 0xff700000 [0001.271] OVR2 PMIC [0001.273] Bpmp FW successfully loaded [0001.276] BoardID = 3448, SKU = 0x0 [0001.279] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.283] Nano-SD: checking PT table on QSPI ... [0001.288] WB0 init successfully at 0xff780000 [0001.293] Set NvDecSticky Bits [0001.296] GSC2 address ff53fffc value c0edbbcc [0001.302] GSC MC Settings done [0001.305] BoardID = 3448, SKU = 0x0 [0001.309] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.312] Nano-SD: checking PT table on QSPI ... [0001.318] TOS Image length 53680 [0001.321] Monitor size 53680 [0001.324] OS size 0 [0001.339] Secure Os AES-CMAC Verification Success! [0001.343] TOS image cipher info: plaintext [0001.347] Loading and Validation of Secure OS Successful [0001.363] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.368] NvTbootPackSdramParams: start. [0001.373] NvTbootPackSdramParams: done. .0633] Bootloader DTB loaded at 0x83000000 [0001.638] Marked DTB cacheable [0001.640] Kernel DTB loaded at 0x83100000 [0001.644] DeviceTree Init done [0001.657] Pinmux applied successfully [0001.662] gicd_base: 0x50041000 [0001.665] gicc_base: 0x50042000 [0001.668] Interrupts Init done [0001.672] Using base:0x60005090 & irq:208 for tick-timer [0001.678] Using base:0x60005098 for delay-timer [0001.682] platform_init_timer: DONE [0001.685] Timer(tick) Init done [0001.689] osc freq = 38400 khz [0001.693] [0001.694] Welcome to L4T Cboot [0001.697] [0001.698] Cboot Version: 00.00.2018.01-t210-39562017 [0001.703] calling constructors [0001.706] initializing heap [0001.709] initializing threads [0001.712] initializing timers [0001.715] creating bootstrap completion thread [0001.719] top of bootstrap2() [0001.722] CPU: ARM Cortex A57 [0001.725] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.730] initializing platform [0001.737] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.742] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.746] Macronix QSPI chip present [0001.750] SPI device register [0001.753] init boot device [0001.755] allocating memory for boot device(SPI) [0001.760] registering boot device [0001.778] QSPI bdev is already initialized [0001.782] Enable APE clock [0001.785] Un-powergate APE partition [0001.788] of_register: registering tegra_udc to of_hal [0001.793] of_register: registering inv20628-driver to of_hal [0001.799] of_register: registering ads1015-driver to of_hal [0001.804] of_register: registering lp8557-bl-driver to of_hal [0001.810] of_register: registering bq2419x_charger to of_hal [0001.816] of_register: registering bq27441_fuel_gauge to of_hal [0001.827] gpio framework initialized [0001.831] of_register: registering tca9539_gpio to of_hal [0001.836] of_register: registering tca9539_gpio to of_hal [0001.842] of_register: registering i2c_bus_driver to of_hal [0001.847] of_register: registering i2c_bus_driver to of_hal [0001.853] of_register: registering i2c_bus_driver to of_hal [0001.858] pmic framework initialized [0001.862] of_register: registering max77620_pmic to of_hal [0001.867] regulator framework initialized [0001.871] of_register: registering tps65132_bl_driver to of_hal [0001.877] initializing target [0001.883] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.891] board ID = D78, board SKU = 0 [0001.895] Skipping Z3! [0001.899] fixed regulator driver initialized [0001.917] initializing OF layer [0001.920] NCK carveout not present [0001.924] Skipping dts_overrides [0001.928] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.945] I2C Bus Init done [0001.947] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.958] I2C Bus Init done [0001.960] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.971] I2C Bus Init done [0001.973] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.984] I2C Bus Init done [0001.987] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.997] I2C Bus Init done [0002.000] of_children_init: Ops found for compatible string maxim,max77620 [0002.010] max77620_init using irq 118 [0002.015] register 'maxim,max77620' pmic [0002.019] gpio_driver_register: register 'max77620-gpio' driver [0002.025] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.036] I2C Bus Init done [0002.039] NCK carveout not present [0002.049] Find /i2c@7000c000's alias i2c0 [0002.053] get eeprom at 1-a0, size 256, type 0 [0002.062] Find /i2c@7000c500's alias i2c2 [0002.066] get eeprom at 3-a0, size 256, type 0 [0002.070] get eeprom at 3-ae, size 256, type 0 [0002.075] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.080] I2C slave not started [0002.083] I2C write failed [0002.086] Writing offset failed [0002.089] eeprom_init: EEPROM read failed [0002.093] pm_ids_update: eeprom init failed [0002.097] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.127] pm_ids_update: The pm board id is 3448-0000-402 [0002.134] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.142] pm_ids_update: pm id update successful [0002.147] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.177] pm_ids_update: The pm board id is 3449-0000-400 [0002.183] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.191] pm_ids_update: pm id update successful [0002.221] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.227] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.235] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.241] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.249] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3d:05:4d [0002.255] Plugin Manager: Parse ODM data 0x000a4000 [0002.268] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.283] Find /i2c@7000c000's alias i2c0 [0002.287] get eeprom at 1-a0, size 256, type 0 [0002.296] Find /i2c@7000c500's alias i2c2 [0002.299] get eeprom at 3-a0, size 256, type 0 [0002.304] get eeprom at 3-ae, size 256, type 0 [0002.308] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.313] I2C slave not started [0002.316] I2C write failed [0002.319] Writing offset failed [0002.322] eeprom_init: EEPROM read failed [0002.326] pm_ids_update: eeprom init failed [0002.330] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.360] pm_ids_update: The pm board id is 3448-0000-402 [0002.367] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.373] pm_ids_update: pm id update successful [0002.378] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.408] pm_ids_update: The pm board id is 3449-0000-400 [0002.414] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.421] pm_ids_update: pm id update successful [0002.452] Add serial number:1421321061962 as DT property [0002.459] Applying platform configs [0002.466] platform-init is not present. Skipping [0002.471] calling apps_init() [0002.476] Couldn't find GPT header [0002.481] Proceeding to Cold Boot [0002.484] starting app android_boot_app [0002.488] Device state: unlocked [0002.491] display console init [0002.499] could not find regulator [0002.503] hdmi cable connected [0002.518] edid read success [0002.533] edid DT entry for leds-pwm not found r[0002.541] ead success [0002.543] width = 640, height = 480, frequency = 25174825 [0002.549] width = 640, height = 480, frequency = 25174825 [0002.554] width = 1920, height = 1080, frequency = 148500000 [0002.560] width = 1920, height = 1080, frequency = 148500000 [0002.565] width = 1920, height = 1080, frequency = 148351648 [0002.571] width = 1280, height = 720, frequency = 74175824 [0002.576] width = 720, height = 480, frequency = 26973026 [0002.582] width = 720, height = 480, frequency = 26973026 [0002.587] width = 640, height = 480, frequency = 25174825 [0002.593] width = 720, height = 576, frequency = 26973026 [0002.598] width = 720, height = 576, frequency = 26973026 [0002.603] width = 1280, height = 720, frequency = 74175824 [0002.609] width = 1920, height = 1080, frequency = 148351648 [0002.614] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.622] tmds-config node not found [0002.626] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.641] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.649] could not find regulator [0002.652] could not find regulator [0002.655] could not find regulator [0002.684] using default cmu settings [0002.687] dc_hdmi_enable, starting HDMI initialisation [0002.693] dc_hdmi_enable, HDMI initialisation complete [0002.698] list and configure display window [0002.707] display console init completed [0002.718] subnode volume_up is not found ! [0002.722] subnode back is not found ! [0002.726] subnode volume_down is not found ! [0002.730] subnode menu is not found ! [0002.734] Gpio keyboard init success [0002.814] found decompressor handler: lz4-legacy [0002.829] decompressing blob (type 1)... [0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x1425a9 [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.281] Read PT from (2:0) [0000.296] Using BFS PT to query partitions [0000.302] Loading Tboot-CPU binary [0000.330] Verifying TBC in OdmNonSecureSBK mode [0000.340] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.347] Bootloader downloaded successfully. [0000.351] Downloaded Tboot-CPU binary to 0xa0000258 [0000.356] MAX77620_GPIO5 configured [0000.359] CPU power rail is up [0000.362] CPU clock enabled [0000.366] Performing RAM repair [0000.369] Updating A64 Warmreset Address to 0xa00002e9 [0000.374] BoardID = 3448, SKU = 0x0 [0000.377] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.381] Nano-SD: checking PT table on QSPI ... [0000.385] Loading NvTbootBootloaderDTB [0000.452] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.525] Bootloader DTB Load Address: 0x83000000 [0000.530] BoardID = 3448, SKU = 0x0 [0000.533] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.537] Nano-SD: checking PT table on QSPI ... [0000.541] Loading NvTbootKernelDTB [0000.607] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.680] Kernel DTB Load Address: 0x83100000 [0000.684] BoardID = 3448, SKU = 0x0 [0000.688] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.692] Nano-SD: checking PT table on QSPI ... [0000.698] Loading cboot binary [0000.814] Verifying EBT in OdmNonSecureSBK mode [0000.855] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.862] Bootloader downloaded successfully. [0000.866] BoardID = 3448, SKU = 0x0 [0000.870] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.873] Nano-SD: checking PT table on QSPI ... [0000.878] PT: Partition NCT NOT found ! [0000.882] Warning: Find Partition via PT Failed [0000.886] Next binary entry address: 0x92c00258 [0000.891] BoardId: 3448 [0000.895] Overriding pmu board id with proc board id [0000.900] Display board id is not available [0000.904] BoardID = 3448, SKU = 0x0 [0000.907] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.911] Nano-SD: checking PT table on QSPI ... [0001.016] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.073] /bpmp deleted [0001.075] SC7EntryFw header found loaded at 0xff700000 [0001.271] OVR2 PMIC [0001.272] Bpmp FW successfully loaded [0001.276] BoardID = 3448, SKU = 0x0 [0001.279] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.283] Nano-SD: checking PT table on QSPI ... [0001.288] WB0 init successfully at 0xff780000 [0001.293] Set NvDecSticky Bits [0001.296] GSC2 address ff53fffc value c0edbbcc [0001.302] GSC MC Settings done [0001.305] BoardID = 3448, SKU = 0x0 [0001.309] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.312] Nano-SD: checking PT table on QSPI ... [0001.318] TOS Image length 53680 [0001.321] Monitor size 53680 [0001.324] OS size 0 [0001.339] Secure Os AES-CMAC Verification Success! [0001.343] TOS image cipher info: plaintext [0001.347] Loading and Validation of Secure OS Successful [0001.363] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.368] NvTbootPackSdramParams: start. [0001.373] NvTbootPackSdramParams: done. [0001.377] Tegraboot started after 51845 us [0001.381] Basic modules init took 886453 us [0001.385] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.390] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.396] Next stage binary read took 102859 us [0001.400] Carveout took -126356 us [0001.403] CPU initialization took 495394 us [0001.407] Total time taken by TegraBoot 1358350 us [0001.412] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 08:37:40, Feb 19 2021 ERROR: Error initializing runtime service trusty_fast [0001.534] RamCode = 0 [0001.539] LPDDR4 Training: Read DT: Number of tables = 2 [0001.544] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.557] EMC Training Successful [0001.560] 408000 not found in DVFS table [0001.566] RamCode = 0 [0001.570] DT Write: emc-table@204000 succeeded [0001.575] DT Write: emc-table@1600000 succeeded [0001.579] LPDDR4 Training: Write DT: Number of tables = 2 [0001.626] [0001.627] Debug Init done [0001.630] Marked DTB cacheable [0001.633] Bootloader DTB loaded at 0x83000000 [0001.638] Marked DTB cacheable [0001.640] Kernel DTB loaded at 0x83100000 [0001.644] DeviceTree Init done [0001.657] Pinmux applied successfully [0001.662] gicd_base: 0x50041000 [0001.665] gicc_base: 0x50042000 [0001.668] Interrupts Init done [0001.672] Using base:0x60005090 & irq:208 for tick-timer [0001.678] Using base:0x60005098 for delay-timer [0001.682] platform_init_timer: DONE [0001.685] Timer(tick) Init done [0001.689] osc freq = 38400 khz [0001.693] [0001.694] Welcome to L4T Cboot [0001.697] [0001.698] Cboot Version: 00.00.2018.01-t210-39562017 [0001.703] calling constructors [0001.706] initializing heap [0001.709] initializing threads [0001.712] initializing timers [0001.715] creating bootstrap completion thread [0001.719] top of bootstrap2() [0001.722] CPU: ARM Cortex A57 [0001.725] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.730] initializing platform [0001.737] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.742] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.746] Macronix QSPI chip present [0001.750] SPI device register [0001.753] init boot device [0001.755] allocating memory for boot device(SPI) [0001.760] registering boot device [0001.768] QSPI bdev is already initialized [0001.772] Enable APE clock [0001.775] Un-powergate APE partition [0001.778] of_register: registering tegra_udc to of_hal [0001.783] of_register: registering inv20628-driver to of_hal [0001.789] of_register: registering ads1015-driver to of_hal [0001.794] of_register: registering lp8557-bl-driver to of_hal [0001.800] of_register: registering bq2419x_charger to of_hal [0001.806] of_register: registering bq27441_fuel_gauge to of_hal [0001.817] gpio framework initialized [0001.821] of_register: registering tca9539_gpio to of_hal [0001.826] of_register: registering tca9539_gpio to of_hal [0001.832] of_register: registering i2c_bus_driver to of_hal [0001.837] of_register: registering i2c_bus_driver to of_hal [0001.843] of_register: registering i2c_bus_driver to of_hal [0001.848] pmic framework initialized [0001.852] of_register: registering max77620_pmic to of_hal [0001.857] regulator framework initialized [0001.861] of_register: registering tps65132_bl_driver to of_hal [0001.867] initializing target [0001.873] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.881] board ID = D78, board SKU = 0 [0001.885] Skipping Z3! [0001.889] fixed regulator driver initialized [0001.907] initializing OF layer [0001.910] NCK carveout not present [0001.914] Skipping dts_overrides [0001.918] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.935] I2C Bus Init done [0001.937] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.948] I2C Bus Init done [0001.950] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.961] I2C Bus Init done [0001.963] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.974] I2C Bus Init done [0001.976] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.987] I2C Bus Init done [0001.990] of_children_init: Ops found for compatible string maxim,max77620 [0002.000] max77620_init using irq 118 [0002.005] register 'maxim,max77620' pmic [0002.009] gpio_driver_register: register 'max77620-gpio' driver [0002.015] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.026] I2C Bus Init done [0002.029] NCK carveout not present [0002.039] Find /i2c@7000c000's alias i2c0 [0002.043] get eeprom at 1-a0, size 256, type 0 [0002.052] Find /i2c@7000c500's alias i2c2 [0002.056] get eeprom at 3-a0, size 256, type 0 [0002.060] get eeprom at 3-ae, size 256, type 0 [0002.065] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.070] I2C slave not started [0002.073] I2C write failed [0002.076] Writing offset failed [0002.079] eeprom_init: EEPROM read failed [0002.083] pm_ids_update: eeprom init failed [0002.087] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.117] pm_ids_update: The pm board id is 3448-0000-402 [0002.124] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.132] pm_ids_update: pm id update successful [0002.137] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.167] pm_ids_update: The pm board id is 3449-0000-400 [0002.173] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.181] pm_ids_update: pm id update successful [0002.211] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.217] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.225] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.231] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.239] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3d:05:4d [0002.245] Plugin Manager: Parse ODM data 0x000a4000 [0002.258] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.273] Find /i2c@7000c000's alias i2c0 [0002.276] get eeprom at 1-a0, size 256, type 0 [0002.285] Find /i2c@7000c500's alias i2c2 [0002.289] get eeprom at 3-a0, size 256, type 0 [0002.294] get eeprom at 3-ae, size 256, type 0 [0002.298] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.303] I2C slave not started [0002.306] I2C write failed [0002.309] Writing offset failed [0002.312] eeprom_init: EEPROM read failed [0002.316] pm_ids_update: eeprom init failed [0002.320] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.350] pm_ids_update: The pm board id is 3448-0000-402 [0002.356] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.363] pm_ids_update: pm id update successful [0002.368] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.398] pm_ids_update: The pm board id is 3449-0000-400 [0002.404] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.411] pm_ids_update: pm id update successful [0002.442] Add serial number:1421321061962 as DT property [0002.449] Applying platform configs [0002.456] platform-init is not present. Skipping [0002.461] calling apps_init() [0002.466] Couldn't find GPT header [0002.471] Proceeding to Cold Boot [0002.474] starting app android_boot_app [0002.478] Device state: unlocked [0002.481] display console init [0002.489] could not find regulator [0002.493] hdmi cable connected [0002.508] edid read success [0002.523] edid rDT entry for leds-pwm not found e[0002.531] ad success [0002.533] width = 640, height = 480, frequency = 25174825 [0002.539] width = 640, height = 480, frequency = 25174825 [0002.544] width = 1920, height = 1080, frequency = 148500000 [0002.550] width = 1920, height = 1080, frequency = 148500000 [0002.555] width = 1920, height = 1080, frequency = 148351648 [0002.561] width = 1280, height = 720, frequency = 74175824 [0002.566] width = 720, height = 480, frequency = 26973026 [0002.572] width = 720, height = 480, frequency = 26973026 [0002.577] width = 640, height = 480, frequency = 25174825 [0002.582] width = 720, height = 576, frequency = 26973026 [0002.588] width = 720, height = 576, frequency = 26973026 [0002.593] width = 1280, height = 720, frequency = 74175824 [0002.599] width = 1920, height = 1080, frequency = 148351648 [0002.604] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.612] tmds-config node not found [0002.616] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.631] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.639] could not find regulator [0002.642] could not find regulator [0002.645] could not find regulator [0002.673] using default cmu settings [0002.677] dc_hdmi_enable, starting HDMI initialisation [0002.683] dc_hdmi_enable, HDMI initialisation complete [0002.688] list and configure display window [0002.697] display console init completed [0002.708] subnode volume_up is not found ! [0002.712] subnode back is not found ! [0002.716] subnode volume_down is not found ! [0002.720] subnode menu is not found ! [0002.724] Gpio keyboard init success [0002.804] found decompressor handler: lz4-legacy [0002.819] decompressing blob (type 1)... [0002.888] load_bmp_blob: panelresolution=1080 type=3 [0002.963] decompressor handler not found [0002.967] load_firmware_blob: Firmware blob loaded, entries=2 [0002.973] XUSB blob version 0 size 124416 @ 0x934ae28c [0002.979] -------> se_aes_verify_sbk_clear: 747 [0002.983] se_aes_verify_sbk_clear: Error [0002.987] SE operation failed [0002.990] bl_battery_charging: connected to external power supply [0003.002] device_query_partition_size: failed to open partition spiflash0:MSC ! [0003.009] MSC Partition not found [0003.016] device_query_partition_size: failed to open partition spiflash0:USP ! [0003.023] USP partition read failed! [0003.026] blob_init: blob-partition USP header read failed [0003.032] android_boot Unable to update recovery partition [0003.037] kfs_getpartname: name = LNX [0003.041] Loading kernel from LNX [0003.050] Found 19 BFS partitions in "spiflash0" [0003.370] load kernel from storage [0003.375] decompressor handler not found [0003.639] Successfully loaded kernel and ramdisk images [0003.644] board ID = D78, board SKU = 0 [0003.649] sdmmc node status = okay [0003.652] sdcard instance = 0 [0003.655] sdcard gpio handle 0x5b [0003.658] sdcard gpio pin 0xc9 [0003.661] sdcard gpio flags 0x0 [0003.664] vmmc-supply 0x9e [0003.667] cd_gpio_pin = 201 [0003.670] pin_state = 0 [0003.672] Found sdcard [0003.674] SD-card IS present ... [0003.677] load_and_boot_kernel: SD card detected OK [0003.683] load_bmp_blob: panelresolution=1080 type=3 [0004.177] display bmp image done [0004.181] NCK carveout not present [0004.184] Skipping dts_overrides [0004.187] NCK carveout not present [0004.197] Find /i2c@7000c000's alias i2c0 [0004.201] get eeprom at 1-a0, size 256, type 0 [0004.210] Find /i2c@7000c500's alias i2c2 [0004.214] get eeprom at 3-a0, size 256, type 0 [0004.218] get eeprom at 3-ae, size 256, type 0 [0004.222] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.228] I2C slave not started [0004.231] I2C write failed [0004.233] Writing offset failed [0004.236] eeprom_init: EEPROM read failed [0004.240] pm_ids_update: eeprom init failed [0004.244] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.274] pm_ids_update: The pm board id is 3448-0000-402 [0004.281] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0004.290] pm_ids_update: pm id update successful [0004.294] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.324] pm_ids_update: The pm board id is 3449-0000-400 [0004.331] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0004.339] pm_ids_update: pm id update successful [0004.369] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.375] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0004.383] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.388] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0004.397] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3d:05:4d [0004.403] Plugin Manager: Parse ODM data 0x000a4000 [0004.415] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0004.424] Add serial number:1421321061962 as DT property [0004.433] "bpmp" doesn't exist, creating [0004.438] Updated bpmp info to DTB [0004.443] Updated initrd info to DTB [0004.447] "proc-board" doesn't exist, creating [0004.453] Updated board info to DTB [0004.456] "pmu-board" doesn't exist, creating [0004.462] Updated board info to DTB [0004.465] "display-board" doesn't exist, creating [0004.471] Updated board info to DTB [0004.475] "reset" doesn't exist, creating [0004.479] Updated reset info to DTB [0004.483] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 [0004.522] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.528] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=tty0 fbcon=map:0 net.ifnames=0 [0004.539] Updated bootarg info to DTB [0004.542] Adding uuid 00000001643174072000000004040100 to DT [0004.548] Adding eks info 0 to DT [0004.554] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.560] Updated memory info to DTB [0004.568] set vdd_core voltage to 1075 mv [0004.572] setting 'vdd-core' regulator to 1075000 micro volts [0004.577] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Feb 19 2021 - 08:37:46 -0800) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2 1 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 822 bytes read in 21 ms (38.1 KiB/s) 1:primary kernel Retrieving file: /boot/initrd 7159841 bytes read in 326 ms (20.9 MiB/s) Retrieving file: /boot/Image 34338824 bytes read in 1503 ms (21.8 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=tty0 fbcon=map:0 net.ifnames=0 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317e68d copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-5294-d8000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Feb 19 08:40:32 PST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.182688] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.328463] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.328549] imx219 7-0010: board setup failed [ 1.352395] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.352464] imx219 8-0010: board setup failed [ 1.374843] soctherm: OC ALARM 0x00000001 [ 2.820953] cgroup: cgroup2: unknown option "nsdelegate" [ 2.885331] soctherm: OC ALARM 0x00000001 [ 3.887675] soctherm: OC ALARM 0x00000001 [ 4.625142] random: crng init done [ 4.628574] random: 7 urandom warning(s) missed due to ratelimiting [ 4.768375] using random self ethernet address [ 4.773070] using random host ethernet address [ 5.293610] soctherm: OC ALARM 0x00000001 [ 6.295678] soctherm: OC ALARM 0x00000001 [ 6.372289] using random self ethernet address [ 6.377000] using random host ethernet address [ 7.300242] soctherm: OC ALARM 0x00000001 [ 8.401272] soctherm: OC ALARM 0x00000001 [ 10.714467] soctherm: OC ALARM 0x00000001 [ 11.716653] soctherm: OC ALARM 0x00000001 [ 13.484299] soctherm: OC ALARM 0x00000001 [ 14.541664] soctherm: OC ALARM 0x00000001 [ 16.074959] soctherm: OC ALARM 0x00000001 [ 17.418236] soctherm: OC ALARM 0x00000001 Ubuntu 18.04.5 LTS nvidia-desktop ttyS0 nvidia-desktop login: [ 18.431611] soctherm: OC ALARM 0x00000001 [ 20.813574] soctherm: OC ALARM 0x00000001 [ 21.815400] soctherm: OC ALARM 0x00000001 [ 22.820194] soctherm: OC ALARM 0x00000001 [ 23.824060] soctherm: OC ALARM 0x00000001 [ 24.827836] soctherm: OC ALARM 0x00000001 [ 25.832187] soctherm: OC ALARM 0x00000001 [ 26.835385] soctherm: OC ALARM 0x00000001 [ 27.839820] soctherm: OC ALARM 0x00000001 [ 28.843854] soctherm: OC ALARM 0x00000001 [ 29.848063] soctherm: OC ALARM 0x00000001 [ 30.852000] soctherm: OC ALARM 0x00000001 [ 31.856184] soctherm: OC ALARM 0x00000001 [ 32.859528] soctherm: OC ALARM 0x00000001 [ 33.863802] soctherm: OC ALARM 0x00000001 [ 35.096663] soctherm: OC ALARM 0x00000001 [ 36.477802] soctherm: OC ALARM 0x00000001 [ 44.424448] soctherm: OC ALARM 0x00000001