[0000.126] [TegraBoot] (version 00.00.2018.01-l4t-33e7fa82) [0000.131] Processing in cold boot mode Bootloader 2 [0000.136] A02 Bootrom Patch rev = 1023 [0000.139] Power-up reason: pmc por [0000.142] No Battery Present [0000.145] pmic max77620 reset reason [0000.148] pmic max77620 NVERC : 0x40 [0000.152] RamCode = 0 [0000.154] Platform has DDR4 type RAM [0000.157] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x925e4 [0000.173] Entering ramdump check [0000.176] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.189] Sdram initialization is successful [0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.217] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.223] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.260] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.272] Invalid GPT Partition [0000.287] Using BFS PT to query partitions [0000.291] failed to load NvTbootTbootCpu from (2:0) [0000.296] re-load NvTbootTbootCpu from (4:0) [0000.441] Csd NumOfBlocks=124735488 [0000.504] Using GPT Primary to query partitions [0000.514] Loading Tboot-CPU binary [0000.891] Verifying TBC in OdmNonSecureSBK mode [0000.901] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.908] Bootloader downloaded successfully. [0000.912] Downloaded Tboot-CPU binary to 0xa0000258 [0000.917] MAX77620_GPIO5 configured [0000.920] CPU power rail is up [0000.923] CPU clock enabled [0000.927] Performing RAM repair [0000.930] Updating A64 Warmreset Address to 0xa00002e9 [0000.935] Loading NvTbootBootloaderDTB [0002.246] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0002.311] Bootloader DTB Load Address: 0x83000000 [0002.316] Loading NvTbootKernelDTB [0003.627] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0003.692] Kernel DTB Load Address: 0x83100000 [0003.703] Loading cboot binary [0005.385] Verifying EBT in OdmNonSecureSBK mode [0005.427] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0005.434] Bootloader downloaded successfully. [0005.628] Using BFS PT to query partitions [0005.632] Next binary entry address: 0x92c00258 [0005.636] BoardId: 3448 [0005.641] Overriding pmu board id with proc board id [0005.645] Display board id is not available [0007.144] Verifying SC7EntryFw in OdmNonSecureSBK mode [0007.196] /bpmp deleted [0007.198] SC7EntryFw header found loaded at 0xff700000 [0007.387] OVR2 PMIC [0007.389] Bpmp FW successfully loaded [0007.407] WB0 init successfully at 0xff780000 [0007.411] Set NvDecSticky Bits [0007.415] GSC2 address ff53fffc value c0edbbcc [0007.421] GSC MC Settings done [0007.429] TOS Image length 53680 [0007.432] Monitor size 53680 [0007.435] OS size 0 [0007.598] Secure Os AES-CMAC Verification Success! [0007.602] TOS image cipher info: plaintext [0007.606] Loading and Validation of Secure OS Successful [0007.622] SC7 Entry Firmware - 0xff700000, 0x4000 [0007.626] NvTbootPackSdramParams: start. [0007.632] NvTbootPackSdramParams: done. [0007.635] Tegraboot started after 53294 us [0007.639] Basic modules init took 5732584 us [0007.643] NvTbootQspiFlashIoctl: Opcode = 1 not supported [0007.649] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB [0007.654] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0007.660] Storage Device Read Time = 6755 ms, Read Size = 2306 KB [0007.665] Storage Device Write Time = 0 ms, Write Size = 0 KB [0007.671] Next stage binary read took 1530216 us [0007.675] Carveout took -1541899 us [0007.679] CPU initialization took 2044844 us [0007.683] Total time taken by TegraBoot 7765745 us [0007.688] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):23b153a63 NOTICE: BL31: Built : 22:39:57, Dec 9 2019 ERROR: Error initializing runtime service trusty_fast [0007.810] RamCode = 0 [0007.815] LPDDR4 Training: Read DT: Number of tables = 2 [0007.820] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0007.832] EMC Training Successful [0007.835] 408000 not found in DVFS table [0007.842] RamCode = 0 [0007.845] DT Write: emc-table@204000 succeeded [0007.851] DT Write: emc-table@1600000 succeeded [0007.855] LPDDR4 Training: Write DT: Number of tables = 2 [0008.053] [0008.054] Debug Init done [0008.056] Marked DTB cacheable [0008.059] Bootloader DTB loaded at 0x83000000 [0008.064] Marked DTB cacheable [0008.067] Kernel DTB loaded at 0x83100000 [0008.071] DeviceTree Init done [0008.086] Pinmux applied successfully [0008.091] gicd_base: 0x50041000 [0008.094] gicc_base: 0x50042000 [0008.097] Interrupts Init done [0008.101] Using base:0x60005090 & irq:208 for tick-timer [0008.107] Using base:0x60005098 for delay-timer [0008.111] platform_init_timer: DONE [0008.115] Timer(tick) Init done [0008.118] osc freq = 38400 khz [0008.122] [0008.124] Welcome to L4T Cboot [0008.127] [0008.128] Cboot Version: 00.00.2018.01-t210-40c3ff9c [0008.133] calling constructors [0008.136] initializing heap [0008.138] initializing threads [0008.141] initializing timers [0008.144] creating bootstrap completion thread [0008.148] top of bootstrap2() [0008.151] CPU: ARM Cortex A57 [0008.154] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0008.159] initializing platform [0008.167] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0008.171] ID LSB = 0x36, ID-CFI len = 194 bytes [0008.176] Macronix QSPI chip present [0008.179] SPI device register [0008.182] init boot device [0008.185] allocating memory for boot device(SPI) [0008.189] registering boot device [0008.198] sdmmc node status = okay [0008.202] sdcard instance = 0 [0008.205] sdcard gpio handle 0x56 [0008.208] sdcard gpio pin 0xc9 [0008.211] sdcard gpio flags 0x0 [0008.214] vmmc-supply 0x99 [0008.216] Instance: 0 [0008.219] Allocating memory for context [0008.222] enabling clock [0008.225] sd card init [0008.227] Check card present and stable [0008.231] Send command 0 [0008.255] Send command 3 [0008.260] Set RCA for the card [0008.262] Query card specific data by command 9 [0008.269] Parse CSD data [0008.271] Send command 7 [0008.282] Calling sd device register [0008.285] Init sdcard [0008.287] Allocating memory for boot device [0008.291] Registering user device [0008.305] Enable APE clock [0008.307] Un-powergate APE partition [0008.311] of_register: registering tegra_udc to of_hal [0008.316] of_register: registering inv20628-driver to of_hal [0008.321] of_register: registering ads1015-driver to of_hal [0008.327] of_register: registering lp8557-bl-driver to of_hal [0008.333] of_register: registering bq2419x_charger to of_hal [0008.338] of_register: registering bq27441_fuel_gauge to of_hal [0008.350] gpio framework initialized [0008.353] of_register: registering tca9539_gpio to of_hal [0008.359] of_register: registering tca9539_gpio to of_hal [0008.364] of_register: registering i2c_bus_driver to of_hal [0008.370] of_register: registering i2c_bus_driver to of_hal [0008.375] of_register: registering i2c_bus_driver to of_hal [0008.381] pmic framework initialized [0008.384] of_register: registering max77620_pmic to of_hal [0008.390] regulator framework initialized [0008.394] of_register: registering tps65132_bl_driver to of_hal [0008.400] initializing target [0008.405] gpio_driver_register: register 'tegra_gpio_driver' driver [0008.413] board ID = D78, board SKU = 0 [0008.417] Skipping Z3! [0008.422] fixed regulator driver initialized [0008.439] initializing OF layer [0008.442] NCK carveout not present [0008.446] Skipping dts_overrides [0008.450] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.467] I2C Bus Init done [0008.469] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.479] I2C Bus Init done [0008.482] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.492] I2C Bus Init done [0008.495] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.505] I2C Bus Init done [0008.508] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.518] I2C Bus Init done [0008.521] of_children_init: Ops found for compatible string maxim,max77620 [0008.531] max77620_init using irq 118 [0008.536] register 'maxim,max77620' pmic [0008.541] gpio_driver_register: register 'max77620-gpio' driver [0008.547] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0008.557] I2C Bus Init done [0008.561] NCK carveout not present [0008.571] Find /i2c@7000c000's alias i2c0 [0008.575] get eeprom at 1-a0, size 256, type 0 [0008.584] Find /i2c@7000c500's alias i2c2 [0008.587] get eeprom at 3-a0, size 256, type 0 [0008.592] get eeprom at 3-ae, size 256, type 0 [0008.596] pm_ids_update: Updating 1,a0, size 256, type 0 [0008.601] I2C slave not started [0008.604] I2C write failed [0008.607] Writing offset failed [0008.610] eeprom_init: EEPROM read failed [0008.614] pm_ids_update: eeprom init failed [0008.618] pm_ids_update: Updating 3,a0, size 256, type 0 [0008.648] pm_ids_update: The pm board id is 3448-0000-400 [0008.655] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0008.663] pm_ids_update: pm id update successful [0008.667] pm_ids_update: Updating 3,ae, size 256, type 0 [0008.673] I2C slave not started [0008.676] I2C write failed [0008.678] Writing offset failed [0008.681] eeprom_init: EEPROM read failed [0008.685] pm_ids_update: eeprom init failed [0008.715] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0008.721] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0008.730] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0008.735] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0008.744] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e7:4d:97 [0008.750] Plugin Manager: Parse ODM data 0x00084000 [0008.761] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0008.782] Find /i2c@7000c000's alias i2c0 [0008.786] get eeprom at 1-a0, size 256, type 0 [0008.795] Find /i2c@7000c500's alias i2c2 [0008.799] get eeprom at 3-a0, size 256, type 0 [0008.803] get eeprom at 3-ae, size 256, type 0 [0008.808] pm_ids_update: Updating 1,a0, size 256, type 0 [0008.813] I2C slave not started [0008.816] I2C write failed [0008.819] Writing offset failed [0008.822] eeprom_init: EEPROM read failed [0008.826] pm_ids_update: eeprom init failed [0008.830] pm_ids_update: Updating 3,a0, size 256, type 0 [0008.860] pm_ids_update: The pm board id is 3448-0000-400 [0008.866] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0008.873] pm_ids_update: pm id update successful [0008.878] pm_ids_update: Updating 3,ae, size 256, type 0 [0008.883] I2C slave not started [0008.886] I2C write failed [0008.889] Writing offset failed [0008.892] eeprom_init: EEPROM read failed [0008.896] pm_ids_update: eeprom init failed [0008.926] Add serial number:1422919174843 as DT property [0008.934] Applying platform configs [0008.941] platform-init is not present. Skipping [0008.945] calling apps_init() [0008.971] Found 14 GPT partitions in "sd0" [0008.975] Proceeding to Cold Boot [0008.978] starting app android_boot_app [0008.982] Device state: unlocked [0008.985] display console init [0008.993] could not find regulator [0009.017] hdmi cable not connected [0009.020] is_hdmi_needed: HDMI not connected,DT entry for leds-pwm not found [0009.030] returning false [0009.033] hdmi is not connected [0009.036] sor0 is not supported [0009.039] display_console_init: no valid display out_type [0009.047] subnode volume_up is not found ! [0009.051] subnode back is not found ! [0009.055] subnode volume_down is not found ! [0009.059] subnode menu is not found ! [0009.062] Gpio keyboard init success [0009.109] found decompressor handler: lz4-legacy [0009.123] decompressing blob (type 1)... [0009.157] display_resolution: No display init [0009.161] Failed to retrieve display resolution [0009.165] Could not load/initialize BMP blob...ignoring [0009.219] decompressor handler not found [0009.223] load_firmware_blob: Firmware blob loaded, entries=2 [0009.229] -------> se_aes_verify_sbk_clear: 747 [0009.233] se_aes_verify_sbk_clear: Error [0009.237] bl_battery_charging: connected to external power supply [0009.244] xusb is supported [0009.250] error while finding nvidia,portmap [0009.755] xusb blob version 0 size 124416 [0009.758] firmware size 124416 [0009.763] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0009.774] xhci0: 64 bytes context size, 32-bit DMA [0009.814] usbus0: 5.0Gbps Super Speed USB v3.0 [0009.834] uhub0: on usbus0 [0010.484] uhub0: 9 ports with 9 removable, self powered [0011.484] failed to get HID devices [0011.487] failed to init xhci or no usb device attached [0011.495] display_console_ioctl: No display init [0011.499] switch_backlight failed [0011.506] device_query_partition_size: failed to open partition sd0:MSC ! [0011.512] MSC Partition not found [0011.519] device_query_partition_size: failed to open partition sd0:USP ! [0011.525] USP partition read failed! [0011.529] blob_init: blob-partition USP header read failed [0011.534] android_boot Unable to update recovery partition [0011.540] kfs_getpartname: name = LNX [0011.543] Loading kernel from LNX [0011.642] load kernel from storage [0011.654] decompressor handler not found [0011.712] Successfully loaded kernel and ramdisk images [0011.718] display_resolution: No display init [0011.722] Failed to retrieve display resolution [0011.727] bmp blob is not loaded and initialized [0011.731] Failed to display boot-logo [0011.735] NCK carveout not present [0011.738] Skipping dts_overrides [0011.741] NCK carveout not present [0011.751] Find /i2c@7000c000's alias i2c0 [0011.755] get eeprom at 1-a0, size 256, type 0 [0011.764] Find /i2c@7000c500's alias i2c2 [0011.768] get eeprom at 3-a0, size 256, type 0 [0011.772] get eeprom at 3-ae, size 256, type 0 [0011.777] pm_ids_update: Updating 1,a0, size 256, type 0 [0011.782] I2C slave not started [0011.785] I2C write failed [0011.788] Writing offset failed [0011.791] eeprom_init: EEPROM read failed [0011.795] pm_ids_update: eeprom init failed [0011.799] pm_ids_update: Updating 3,a0, size 256, type 0 [0011.829] pm_ids_update: The pm board id is 3448-0000-400 [0011.836] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0011.844] pm_ids_update: pm id update successful [0011.848] pm_ids_update: Updating 3,ae, size 256, type 0 [0011.853] I2C slave not started [0011.856] I2C write failed [0011.859] Writing offset failed [0011.862] eeprom_init: EEPROM read failed [0011.866] pm_ids_update: eeprom init failed [0011.896] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0011.902] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0011.910] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0011.916] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0011.925] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e7:4d:97 [0011.931] Plugin Manager: Parse ODM data 0x00084000 [0011.942] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0011.957] Add serial number:1422919174843 as DT property [0011.965] "bpmp" doesn't exist, creating [0011.971] Updated bpmp info to DTB [0011.976] Updated initrd info to DTB [0011.979] "proc-board" doesn't exist, creating [0011.985] Updated board info to DTB [0011.988] "pmu-board" doesn't exist, creating [0011.994] Updated board info to DTB [0011.997] "display-board" doesn't exist, creating [0012.003] Updated board info to DTB [0012.006] "reset" doesn't exist, creating [0012.011] Updated reset info to DTB [0012.014] display_console_ioctl: No display init [0012.019] display_console_ioctl: No display init [0012.023] display_console_ioctl: No display init [0012.028] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 [0012.062] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0012.074] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0012.087] Updated bootarg info to DTB [0012.091] Adding uuid 00000001644577832400000016ff81c0 to DT [0012.097] Adding eks info 0 to DT [0012.102] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0012.108] Updated memory info to DTB [0012.117] set vdd_core voltage to 1125 mv [0012.121] setting 'vdd-core' regulator to 1125000 micro volts [0012.144] Found secure-pmc; disable BPMP U-Boot 2016.07-g0536cf2a27 (Dec 09 2019 - 22:40:32 -0800) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 1  0 Tegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Tegra SD/MMC: 0, Tegra SD/MMC:yegra210 (P3450-Porg) # MC: Te