Welcome to minicom 2.8 OPTIONS: I18n Port /dev/ttyUSB0, 17:00:39 Press CTRL-A Z for help on special keys [0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x190ded [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.281] Initialize FailControl [0000.284] Read PT from (2:0) [0000.314] PT crc32 and magic check passed. [0000.318] Using BFS PT to query partitions [0000.324] Loading Tboot-CPU binary [0000.352] Verifying TBC in OdmNonSecureSBK mode [0000.362] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.369] Bootloader downloaded successfully. [0000.373] Downloaded Tboot-CPU binary to 0xa0000258 [0000.378] MAX77620_GPIO5 configured [0000.381] CPU power rail is up [0000.384] CPU clock enabled [0000.388] Performing RAM repair [0000.391] Updating A64 Warmreset Address to 0xa00002e9 [0000.396] BoardID = 3448, SKU = 0x0 [0000.399] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.403] Nano-SD: checking PT table on QSPI ... [0000.407] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.413] Loading NvTbootBootloaderDTB [0000.480] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.551] Bootloader DTB Load Address: 0x83000000 [0000.556] BoardID = 3448, SKU = 0x0 [0000.559] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.563] Nano-SD: checking PT table on QSPI ... [0000.567] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.574] Loading NvTbootKernelDTB [0000.640] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.711] Kernel DTB Load Address: 0x83100000 [0000.715] BoardID = 3448, SKU = 0x0 [0000.718] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.722] Nano-SD: checking PT table on QSPI ... [0000.727] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.734] Loading cboot binary [0000.850] Verifying EBT in OdmNonSecureSBK mode [0000.892] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.899] Bootloader downloaded successfully. [0000.903] BoardID = 3448, SKU = 0x0 [0000.906] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.910] Nano-SD: checking PT table on QSPI ... [0000.914] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.921] PT: Partition NCT NOT found ! [0000.924] Warning: Find Partition via PT Failed [0000.929] Next binary entry address: 0x92c00258 [0000.933] BoardId: 3448 [0000.938] Overriding pmu board id with proc board id [0000.942] Display board id is not available [0000.947] BoardID = 3448, SKU = 0x0 [0000.950] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.954] Nano-SD: checking PT table on QSPI ... [0000.958] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.065] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.121] /bpmp deleted [0001.123] SC7EntryFw header found loaded at 0xff700000 [0001.311] OVR2 PMIC [0001.313] Bpmp FW successfully loaded [0001.316] BoardID = 3448, SKU = 0x0 [0001.320] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.324] Nano-SD: checking PT table on QSPI ... [0001.328] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.335] WB0 init successfully at 0xff780000 [0001.339] Verifying NvTbootWb0 in OdmNonSecureSBK mode [0001.344] Set NvDecSticky Bits [0001.348] GSC2 address ff53fffc value c0edbbcc [0001.354] GSC MC Settings done [0001.357] BoardID = 3448, SKU = 0x0 [0001.360] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.364] Nano-SD: checking PT table on QSPI ... [0001.368] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.375] TOS Image length 53680 [0001.378] Monitor size 53680 [0001.381] OS size 0 [0001.396] Secure Os AES-CMAC Verification Success! [0001.401] TOS image cipher info: plaintext [0001.405] Loading and Validation of Secure OS Successful [0001.421] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.425] NvTbootPackSdramParams: start. [0001.431] NvTbootPackSdramParams: done. [0001.434] Tegraboot started after 51864 us [0001.438] Basic modules init took 936079 us [0001.442] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.448] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.453] Next stage binary read took 102860 us [0001.458] Carveout took -132465 us [0001.461] CPU initialization took 510786 us [0001.465] Total time taken by TegraBoot 1417260 us [0001.470] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):9892ce1 NOTICE: BL31: Built : 09:21:33, Nov 22 2022 ERROR: Error initializing runtime service trusty_fast [0001.592] RamCode = 0 [0001.596] LPDDR4 Training: Read DT: Number of tables = 2 [0001.601] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.614] EMC Training Successful [0001.617] 408000 not found in DVFS table [0001.623] RamCode = 0 [0001.627] DT Write: emc-table@204000 succeeded [0001.632] DT Write: emc-table@1600000 succeeded [0001.637] LPDDR4 Training: Write DT: Number of tables = 2 [0001.685] [0001.686] Debug Init done [0001.688] Marked DTB cacheable [0001.691] Bootloader DTB loaded at 0x83000000 [0001.696] Marked DTB cacheable [0001.699] Kernel DTB loaded at 0x83100000 [0001.703] DeviceTree Init done [0001.716] Pinmux applied successfully [0001.720] gicd_base: 0x50041000 [0001.724] gicc_base: 0x50042000 [0001.727] Interrupts Init done [0001.731] Using base:0x60005090 & irq:208 for tick-timer [0001.736] Using base:0x60005098 for delay-timer [0001.741] platform_init_timer: DONE [0001.744] Timer(tick) Init done [0001.748] osc freq = 38400 khz [0001.752] [0001.753] Welcome to L4T Cboot [0001.756] [0001.757] Cboot Version: 00.00.2018.01-t210-a2f2e4b8 [0001.762] calling constructors [0001.765] initializing heap [0001.768] initializing threads [0001.771] initializing timers [0001.773] creating bootstrap completion thread [0001.778] top of bootstrap2() [0001.781] CPU: ARM Cortex A57 [0001.784] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.788] initializing platform [0001.796] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.800] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.805] Macronix QSPI chip present [0001.808] SPI device register [0001.811] init boot device [0001.814] allocating memory for boot device(SPI) [0001.818] registering boot device [0001.827] QSPI bdev is already initialized [0001.830] Enable APE clock [0001.833] Un-powergate APE partition [0001.837] of_register: registering tegra_udc to of_hal [0001.842] of_register: registering inv20628-driver to of_hal [0001.847] of_register: registering ads1015-driver to of_hal [0001.853] of_register: registering lp8557-bl-driver to of_hal [0001.859] of_register: registering bq2419x_charger to of_hal [0001.864] of_register: registering bq27441_fuel_gauge to of_hal [0001.876] gpio framework initialized [0001.879] of_register: registering tca9539_gpio to of_hal [0001.884] of_register: registering tca9539_gpio to of_hal [0001.890] of_register: registering i2c_bus_driver to of_hal [0001.895] of_register: registering i2c_bus_driver to of_hal [0001.901] of_register: registering i2c_bus_driver to of_hal [0001.907] pmic framework initialized [0001.910] of_register: registering max77620_pmic to of_hal [0001.915] regulator framework initialized [0001.919] of_register: registering tps65132_bl_driver to of_hal [0001.925] initializing target [0001.931] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.939] board ID = D78, board SKU = 0 [0001.943] Skipping Z3! [0001.948] fixed regulator driver initialized [0001.966] initializing OF layer [0001.968] NCK carveout not present [0001.972] Skipping dts_overrides [0001.976] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.993] I2C Bus Init done [0001.995] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.005] I2C Bus Init done [0002.008] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.018] I2C Bus Init done [0002.021] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.031] I2C Bus Init done [0002.034] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.044] I2C Bus Init done [0002.047] of_children_init: Ops found for compatible string maxim,max77620 [0002.057] max77620_init using irq 118 [0002.062] register 'maxim,max77620' pmic [0002.066] gpio_driver_register: register 'max77620-gpio' driver [0002.073] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.083] I2C Bus Init done [0002.087] NCK carveout not present [0002.096] Find /i2c@7000c000's alias i2c0 [0002.100] get eeprom at 1-a0, size 256, type 0 [0002.109] Find /i2c@7000c500's alias i2c2 [0002.113] get eeprom at 3-a0, size 256, type 0 [0002.117] get eeprom at 3-ae, size 256, type 0 [0002.121] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.127] I2C slave not started [0002.130] I2C write failed [0002.132] Writing offset failed [0002.135] eeprom_init: EEPROM read failed [0002.139] pm_ids_update: eeprom init failed [0002.144] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.174] pm_ids_update: The pm board id is 3448-0000-402 [0002.180] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.189] pm_ids_update: pm id update successful [0002.193] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.223] pm_ids_update: The pm board id is 3449-0000-400 [0002.230] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.238] pm_ids_update: pm id update successful [0002.268] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.274] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.282] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.288] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.296] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3c:b1:2b [0002.302] Plugin Manager: Parse ODM data 0x000a4000 [0002.314] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7 [0002.329] Find /i2c@7000c000's alias i2c0 [0002.333] get eeprom at 1-a0, size 256, type 0 [0002.342] Find /i2c@7000c500's alias i2c2 [0002.346] get eeprom at 3-a0, size 256, type 0 [0002.350] get eeprom at 3-ae, size 256, type 0 [0002.354] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.360] I2C slave not started [0002.363] I2C write failed [0002.365] Writing offset failed [0002.368] eeprom_init: EEPROM read failed [0002.372] pm_ids_update: eeprom init failed [0002.376] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.406] pm_ids_update: The pm board id is 3448-0000-402 [0002.413] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.420] pm_ids_update: pm id update successful [0002.424] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.454] pm_ids_update: The pm board id is 3449-0000-400 [0002.460] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.467] pm_ids_update: pm id update successful [0002.498] Add serial number:1420821027969 as DT property [0002.505] Applying platform configs [0002.512] platform-init is not present. Skipping [0002.516] calling apps_init() [0002.522] Couldn't find GPT header [0002.527] Proceeding to Cold Boot [0002.530] starting app android_boot_app [0002.534] Device state: unlocked [0002.537] display console init [0002.545] could not find regulator [0002.549] hdmi cable connected [0002.564] edid read success [0002.579] edid read success [0002.582] width DT entry for leds-pwm not found =[0002.590] 640, height = 480, frequency = 25174825 [0002.594] width = 1360, height = 768, frequency = 85500000 [0002.600] width = 1280, height = 720, frequency = 74250000 [0002.605] width = 1920, height = 1080, frequency = 148351648 [0002.611] width = 1920, height = 1080, frequency = 148351648 [0002.617] width = 1280, height = 720, frequency = 74175824 [0002.622] width = 1280, height = 720, frequency = 74175824 [0002.628] width = 1920, height = 1080, frequency = 74175824 [0002.633] width = 1920, height = 1080, frequency = 74175824 [0002.639] width = 720, height = 576, frequency = 26973026 [0002.644] width = 720, height = 480, frequency = 26973026 [0002.649] width = 720, height = 576, frequency = 26973026 [0002.655] width = 720, height = 480, frequency = 26973026 [0002.660] width = 640, height = 480, frequency = 25174825 [0002.666] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.673] tmds-config node not found [0002.677] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltageps [0002.692] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.700] could not find regulator [0002.703] could not find regulator [0002.706] could not find regulator [0002.735] using default cmu settings [0002.738] dc_hdmi_enable, starting HDMI initialisation [0002.744] dc_hdmi_enable, HDMI initialisation complete [0002.749] list and configure display window [0002.758] display console init completed [0002.769] subnode volume_up is not found ! [0002.773] subnode back is not found ! [0002.777] subnode volume_down is not found ! [0002.781] subnode menu is not found ! [0002.785] Gpio keyboard init success [0002.865] found decompressor handler: lz4-legacy [0002.880] decompressing blob (type 1)... [0002.949] load_bmp_blob: panelresolution=1080 type=3 [0002.954] -------> se_aes_verify_sbk_clear: 747 [0002.959] se_aes_verify_sbk_clear: Error [0002.963] SE operation failed [0002.965] bl_battery_charging: connected to external power supply [0002.978] device_query_partition_size: failed to open partition spiflash0:MSC ! [0002.985] MSC Partition not found [0002.991] device_query_partition_size: failed to open partition spiflash0:USP ! [0002.999] USP partition read failed! [0003.002] blob_init: blob-partition USP header read failed [0003.008] android_boot Unable to update recovery partition [0003.013] kfs_getpartname: name = LNX [0003.017] Loading kernel from LNX [0003.026] Found 19 BFS partitions in "spiflash0" [0003.348] load kernel from storage [0003.353] decompressor handler not found [0003.619] Successfully loaded kernel and ramdisk images [0003.624] board ID = D78, board SKU = 0 [0003.629] sdmmc node status = okay [0003.632] sdcard instance = 0 [0003.635] sdmmc cd-inverted [0003.638] sdcard gpio handle 0x5b [0003.641] sdcard gpio pin 0xc9 [0003.644] sdcard gpio flags 0x0 [0003.647] vmmc-supply 0x9d [0003.649] cd_gpio_pin = 201 [0003.652] pin_state = 0 [0003.654] Found sdcard [0003.657] SD-card IS present ... [0003.660] load_and_boot_kernel: SD card detected OK [0003.666] load_bmp_blob: panelresolution=1080 type=3 [0004.160] display bmp image done [0004.163] NCK carveout not present [0004.166] Skipping dts_overrides [0004.169] NCK carveout not present [0004.179] Find /i2c@7000c000's alias i2c0 [0004.183] get eeprom at 1-a0, size 256, type 0 [0004.192] Find /i2c@7000c500's alias i2c2 [0004.195] get eeprom at 3-a0, size 256, type 0 [0004.200] get eeprom at 3-ae, size 256, type 0 [0004.204] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.209] I2C slave not started [0004.212] I2C write failed [0004.215] Writing offset failed [0004.218] eeprom_init: EEPROM read failed [0004.222] pm_ids_update: eeprom init failed [0004.226] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.256] pm_ids_update: The pm board id is 3448-0000-402 [0004.263] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0004.272] pm_ids_update: pm id update successful [0004.276] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.306] pm_ids_update: The pm board id is 3449-0000-400 [0004.312] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0004.320] pm_ids_update: pm id update successful [0004.351] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.357] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0004.364] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.370] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0004.379] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3c:b1:2b [0004.385] Plugin Manager: Parse ODM data 0x000a4000 [0004.397] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7 [0004.406] Add serial number:1420821027969 as DT property [0004.415] "bpmp" doesn't exist, creating [0004.420] Updated bpmp info to DTB [0004.425] Updated initrd info to DTB [0004.428] "proc-board" doesn't exist, creating [0004.434] Updated board info to DTB [0004.438] "pmu-board" doesn't exist, creating [0004.444] Updated board info to DTB [0004.447] "display-board" doesn't exist, creating [0004.453] Updated board info to DTB [0004.456] "reset" doesn't exist, creating [0004.461] Updated reset info to DTB [0004.464] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype [0004.504] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.509] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 [0004.522] Updated bootarg info to DTB [0004.526] Adding uuid 00000001642e12c31800000004040040 to DT [0004.532] Adding eks info 0 to DT [0004.537] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.543] Updated memory info to DTB [0004.551] set vdd_core voltage to 1125 mv [0004.555] setting 'vdd-core' regulator to 1125000 micro volts [0004.561] Found secure-pmc; disable BPMP U-Boot 2020.04-g4335beb (Nov 22 2022 - 09:21:37 -0800) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 25B *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 845 bytes read in 33 ms (24.4 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7160134 bytes read in 349 ms (19.6 MiB/s) Retrieving file: /boot/Image 34629640 bytes read in 1515 ms (21.8 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resiz ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317cf27 copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.299-tegra (buildbrain@mobile-u64-5333-d8000) (2 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.149307] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.330914] imx219 7-0010: imx219_board_setup: error during i2c read probe () [ 1.330984] imx219 7-0010: board setup failed [ 1.354897] imx219 8-0010: imx219_board_setup: error during i2c read probe () [ 1.354991] imx219 8-0010: board setup failed [ 2.800359] cgroup: cgroup2: unknown option "nsdelegate" [ 4.496047] using random self ethernet address [ 4.503916] using random host ethernet address [ 4.669064] random: crng init done [ 4.673493] random: 7 urandom warning(s) missed due to ratelimiting [ 4.718184] [UFW BLOCK] IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:8 [ 5.110189] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-26.u2 [ 5.120680] iwlwifi 0000:01:00.0: Falling back to user helper [ 5.353481] using random self ethernet address [ 5.361457] using random host ethernet address [ 5.370125] [UFW BLOCK] IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:8 [ 6.224659] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-25.u2 [ 6.236698] iwlwifi 0000:01:00.0: Falling back to user helper [ 6.689036] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-24.u2 [ 6.702078] iwlwifi 0000:01:00.0: Falling back to user helper [ 6.970601] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-23.u2 [ 6.981167] iwlwifi 0000:01:00.0: Falling back to user helper [ 7.603345] thermal thermal_zone6: failed to read out thermal zone (-5) [ 7.849095] pcieport 0000:00:01.0: PCIe Bus Error: severity=Corrected, type=) [ 7.860744] pcieport 0000:00:01.0: device [10de:0fae] error status/mask=000 [ 7.870571] pcieport 0000:00:01.0: [ 0] Receiver Error (First) [ 8.338461] Bridge firewalling registered Ubuntu 18.04.6 LTS rosa-desktop ttyS0 rosa-desktop login: [ 11.946420] [UFW BLOCK] IN=lo OUT= MAC=00:00:00:00:00:00 [ 12.258613] [UFW BLOCK] IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:8 [ 13.241183] [UFW BLOCK] IN=wlan0 OUT= MAC= SRC=fe80:0000:0000:0000:88b5:6675 [ 13.251989] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:01:40:3f:8c:f5:1f:8 [ 13.357109] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 13.491374] [UFW BLOCK] IN=wlan0 OUT= MAC= SRC=fe80:0000:0000:0000:88b5:6675 [ 13.742467] [UFW BLOCK] IN=wlan0 OUT= MAC= SRC=fe80:0000:0000:0000:88b5:6675 [ 13.943195] [UFW BLOCK] IN=wlan0 OUT= MAC= SRC=fe80:0000:0000:0000:88b5:6675 [ 24.825479] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 45.717809] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 65.277066] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 82.269175] [UFW BLOCK] IN=wlan0 OUT= MAC=01:00:5e:00:00:01:40:3f:8c:f5:1f:8 [ 85.243475] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 105.212646] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 125.175897] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 146.065404] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 165.111144] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:c6:b5:58:9c:5d:e [ 184.874211] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:d6:2c:e7:90:bb:3 [ 205.047360] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 207.297957] [UFW BLOCK] IN=wlan0 OUT= MAC=01:00:5e:00:00:01:40:3f:8c:f5:1f:8 [ 227.679864] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 246.316734] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 264.850719] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 285.022793] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f [ 305.603515] [UFW BLOCK] IN=wlan0 OUT= MAC=33:33:00:00:00:fb:9c:3e:53:91:24:f