Welcome to minicom 2.7 OPTIONS: I18n Compiled on Nov 15 2018, 20:18:47. Port /dev/ttyUSB0, 20:40:12 Press CTRL-A Z for help on special keys T [0000.222] [L4T TegraBoot] (version 00.00.2018.01-l4t-80a468da) [0000.228] Processing in cold boot mode Bootloader 2 [0000.232] A02 Bootrom Patch rev = 1023 [0000.236] Power-up reason: pmc por [0000.239] No Battery Present [0000.242] pmic max77620 reset reason [0000.245] pmic max77620 NVERC : 0x40 [0000.249] RamCode = 0 [0000.251] Platform has DDR4 type RAM [0000.254] max77620 disabling SD1 Remote Sense [0000.258] Setting DDR voltage to 1125mv [0000.262] Serial Number of Pmic Max77663: 0x1029f9 [0000.270] Entering ramdump check [0000.273] Get RamDumpCarveOut = 0x0 [0000.276] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.281] Last reboot was clean, booting normally! [0000.286] Sdram initialization is successful [0000.290] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.296] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.302] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.308] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.314] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.320] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.325] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.331] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.347] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.353] Platform-DebugCarveout: 0 [0000.357] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.362] Non secure mode, and RB not enabled. [0000.379] Csd NumOfBlocks=0 [0000.571] *** Booting BFS0. [0000.573] Read PT from (0:3) [0000.579] Using BFS PT to query partitions [0000.584] PT: Partition LNX NOT found ! [0001.171] *** Booting KFS0. [0001.174] Read GPT from (0:3) [0001.178] Using GPT Primary to query partitions [0001.183] Loading Tboot-CPU binary [0001.190] Verifying TBC in OdmNonSecureSBK mode [0001.200] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0001.207] Bootloader downloaded successfully. [0001.211] Downloaded Tboot-CPU binary to 0xa0000258 [0001.216] MAX77620_GPIO5 configured [0001.219] CPU power rail is up [0001.222] CPU clock enabled [0001.226] Performing RAM repair [0001.229] Updating A64 Warmreset Address to 0xa00002e9 [0001.234] Loading NvTbootBootloaderDTB [0001.251] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0001.317] Bootloader DTB Load Address: 0x83000000 [0001.321] Loading NvTbootKernelDTB [0001.338] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0001.403] Kernel DTB Load Address: 0x83100000 [0001.409] Loading cboot binary [0001.419] Verifying EBT in OdmNonSecureSBK mode [0001.461] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0001.468] Bootloader downloaded successfully. [0001.473] PT: Partition NCT NOT found ! [0001.476] Warning: Find Partition via PT Failed [0001.481] Next binary entry address: 0x92c00258 [0001.485] BoardId: 3448 [0001.490] Overriding pmu board id with proc board id [0001.494] Display board id is not available [0001.506] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.558] /bpmp deleted [0001.560] SC7EntryFw header found loaded at 0xff700000 [0001.750] OVR2 PMIC [0001.752] Bpmp FW successfully loaded [0001.757] WB0 init successfully at 0xff780000 [0001.761] Set NvDecSticky Bits [0001.765] GSC2 address ff53fffc value c0edbbcc [0001.771] GSC MC Settings done [0001.774] TOS Image length 53680 [0001.777] Monitor size 53680 [0001.780] OS size 0 [0001.785] Secure Os AES-CMAC Verification Success! [0001.790] TOS image cipher info: plaintext [0001.794] Loading and Validation of Secure OS Successful [0001.810] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.814] NvTbootPackSdramParams: start. [0001.819] NvTbootPackSdramParams: done. [0001.823] Tegraboot started after 151900 us [0001.827] Basic modules init took 1383524 us [0001.831] Sec Bootdevice Read Time = 546 ms, Read Size = 14459 KB [0001.837] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.843] Next stage binary read took 7367 us [0001.847] Carveout took -19270 us [0001.850] CPU initialization took 343834 us [0001.854] Total time taken by TegraBoot 1715455 us [0001.859] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):41d46a9cf NOTICE: BL31: Built : 21:18:12, Jun 25 2020 ERROR: Error initializing runtime service trusty_fast [0001.981] RamCode = 0 [0001.986] LPDDR4 Training: Read DT: Number of tables = 2 [0001.991] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0002.003] EMC Training Successful [0002.006] 408000 not found in DVFS table [0002.013] RamCode = 0 [0002.016] DT Write: emc-table@204000 succeeded [0002.022] DT Write: emc-table@1600000 succeeded [0002.026] LPDDR4 Training: Write DT: Number of tables = 2 [0002.084] [0002.085] Debug Init done [0002.087] Marked DTB cacheable [0002.090] Bootloader DTB loaded at 0x83000000 [0002.095] Marked DTB cacheable [0002.098] Kernel DTB loaded at 0x83100000 [0002.102] DeviceTree Init done [0002.115] Pinmux applied successfully [0002.119] gicd_base: 0x50041000 [0002.122] gicc_base: 0x50042000 [0002.125] Interrupts Init done [0002.130] Using base:0x60005090 & irq:208 for tick-timer [0002.135] Using base:0x60005098 for delay-timer [0002.139] platform_init_timer: DONE [0002.143] Timer(tick) Init done [0002.146] osc freq = 38400 khz [0002.151] [0002.152] Welcome to L4T Cboot [0002.155] [0002.156] Cboot Version: 00.00.2018.01-t210-3a7ad565 [0002.161] calling constructors [0002.164] initializing heap [0002.166] initializing threads [0002.169] initializing timers [0002.172] creating bootstrap completion thread [0002.177] top of bootstrap2() [0002.179] CPU: ARM Cortex A57 [0002.182] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0002.187] initializing platform [0002.241] Config for emmc ddr50 mode completed [0002.245] sdmmc bdev is already initialized [0002.249] Enable APE clock [0002.252] Un-powergate APE partition [0002.255] of_register: registering tegra_udc to of_hal [0002.261] of_register: registering inv20628-driver to of_hal [0002.266] of_register: registering ads1015-driver to of_hal [0002.272] of_register: registering lp8557-bl-driver to of_hal [0002.277] of_register: registering bq2419x_charger to of_hal [0002.283] of_register: registering bq27441_fuel_gauge to of_hal [0002.295] gpio framework initialized [0002.298] of_register: registering tca9539_gpio to of_hal [0002.303] of_register: registering tca9539_gpio to of_hal [0002.309] of_register: registering i2c_bus_driver to of_hal [0002.314] of_register: registering i2c_bus_driver to of_hal [0002.320] of_register: registering i2c_bus_driver to of_hal [0002.325] pmic framework initialized [0002.329] of_register: registering max77620_pmic to of_hal [0002.334] regulator framework initialized [0002.338] of_register: registering tps65132_bl_driver to of_hal [0002.344] initializing target [0002.350] gpio_driver_register: register 'tegra_gpio_driver' driver [0002.361] fixed regulator driver initialized [0002.378] initializing OF layer [0002.381] NCK carveout not present [0002.385] Skipping dts_overrides [0002.389] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.406] I2C Bus Init done [0002.408] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.419] I2C Bus Init done [0002.421] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.432] I2C Bus Init done [0002.434] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.445] I2C Bus Init done [0002.447] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.458] I2C Bus Init done [0002.460] of_children_init: Ops found for compatible string maxim,max77620 [0002.471] max77620_init using irq 118 [0002.475] register 'maxim,max77620' pmic [0002.480] gpio_driver_register: register 'max77620-gpio' driver [0002.486] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.496] I2C Bus Init done [0002.500] NCK carveout not present [0002.510] Find /i2c@7000c000's alias i2c0 [0002.514] get eeprom at 1-a0, size 256, type 0 [0002.523] Find /i2c@7000c500's alias i2c2 [0002.527] get eeprom at 3-a0, size 256, type 0 [0002.531] get eeprom at 3-ae, size 256, type 0 [0002.535] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.541] I2C slave not started [0002.544] I2C write failed [0002.546] Writing offset failed [0002.549] eeprom_init: EEPROM read failed [0002.553] pm_ids_update: eeprom init failed [0002.557] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.588] pm_ids_update: The pm board id is 3448-0002-400 [0002.594] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0002.602] pm_ids_update: pm id update successful [0002.607] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.637] pm_ids_update: The pm board id is 3449-0000-400 [0002.643] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.651] pm_ids_update: pm id update successful [0002.682] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.688] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.696] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.702] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.710] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ea:34:98 [0002.717] Plugin Manager: Parse ODM data 0x00094000 [0002.727] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.742] Find /i2c@7000c000's alias i2c0 [0002.745] get eeprom at 1-a0, size 256, type 0 [0002.754] Find /i2c@7000c500's alias i2c2 [0002.758] get eeprom at 3-a0, size 256, type 0 [0002.763] get eeprom at 3-ae, size 256, type 0 [0002.767] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.772] I2C slave not started [0002.775] I2C write failed [0002.778] Writing offset failed [0002.781] eeprom_init: EEPROM read failed [0002.785] pm_ids_update: eeprom init failed [0002.789] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.819] pm_ids_update: The pm board id is 3448-0002-400 [0002.826] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0002.833] pm_ids_update: pm id update successful [0002.837] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.867] pm_ids_update: The pm board id is 3449-0000-400 [0002.874] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.881] pm_ids_update: pm id update successful [0002.911] Add serial number:1423519040734 as DT property [0002.919] Applying platform configs [0002.926] platform-init is not present. Skipping [0002.930] calling apps_init() [0002.946] Found 17 GPT partitions in "sdmmc3_user" [0002.951] Proceeding to Cold Boot [0002.954] starting app android_boot_app [0002.958] Device state: unlocked [0002.961] display console init [0002.970] could not find regulator [0002.973] hdmi cable connected [0002.988] edid read success [0003.006] DT entry for leds-pwm not found [0003.009] edid read success [0003.012] width = 640, height = 480, frequency = 25174825 [0003.017] width = 2560, height = 1440, frequency = 241500000 [0003.023] width = 1920, height = 1080, frequency = 148500000 [0003.029] width = 1920, height = 1080, frequency = 148351648 [0003.034] width = 1920, height = 1080, frequency = 148351648 [0003.040] width = 1280, height = 720, frequency = 74175824 [0003.046] width = 1280, height = 720, frequency = 74175824 [0003.051] width = 720, height = 480, frequency = 26973026 [0003.056] width = 720, height = 576, frequency = 26973026 [0003.062] width = 720, height = 480, frequency = 26973026 [0003.067] width = 720, height = 576, frequency = 26973026 [0003.072] width = 640, height = 480, frequency = 25174825 [0003.078] Best mode Width = 1920, Height = 1080, freq = 148351648 [0003.086] tmds-config node not found [0003.090] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0003.104] setting 'vdd-1v8' regulator to 1800000 micro volts [0003.112] could not find regulator [0003.115] could not find regulator [0003.119] could not find regulator [0003.147] using default cmu settings [0003.151] dc_hdmi_enable, starting HDMI initialisation [0003.157] dc_hdmi_enable, HDMI initialisation complete [0003.162] list and configure display window [0003.171] display console init completed [0003.182] subnode volume_up is not found ! [0003.186] subnode back is not found ! [0003.189] subnode volume_down is not found ! [0003.193] subnode menu is not found ! [0003.197] Gpio keyboard init success [0003.244] found decompressor handler: lz4-legacy [0003.259] decompressing blob (type 1)... [0003.294] load_bmp_blob: panelresolution=1080 type=3 [0003.344] decompressor handler not found [0003.347] load_firmware_blob: Firmware blob loaded, entries=2 [0003.353] -------> se_aes_verify_sbk_clear: 747 [0003.358] se_aes_verify_sbk_clear: Error [0003.361] bl_battery_charging: connected to external power supply [0003.369] xusb is supported [0003.375] error while finding nvidia,portmap [0003.879] xusb blob version 0 size 124416 [0003.883] firmware size 124416 [0003.888] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0003.902] xhci0: 64 bytes context size, 32-bit DMA [0003.942] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.962] uhub0: on usbus0 [0004.612] uhub0: 9 ports with 9 removable, self powered [0005.612] failed to get HID devices [0005.616] failed to init xhci or no usb device attached [0005.629] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0005.637] MSC Partition not found [0005.646] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [0005.654] USP partition read failed! [0005.657] blob_init: blob-partition USP header read failed [0005.663] android_boot Unable to update recovery partition [0005.668] kfs_getpartname: name = LNX [0005.672] Loading kernel from LNX [0005.736] load kernel from storage [0005.746] decompressor handler not found [0005.765] Successfully loaded kernel and ramdisk images [0005.771] load_bmp_blob: panelresolution=1080 type=3 [0006.266] display bmp image done [0006.269] NCK carveout not present [0006.272] Skipping dts_overrides [0006.275] NCK carveout not present [0006.285] Find /i2c@7000c000's alias i2c0 [0006.289] get eeprom at 1-a0, size 256, type 0 [0006.298] Find /i2c@7000c500's alias i2c2 [0006.302] get eeprom at 3-a0, size 256, type 0 [0006.306] get eeprom at 3-ae, size 256, type 0 [0006.311] pm_ids_update: Updating 1,a0, size 256, type 0 [0006.316] I2C slave not started [0006.319] I2C write failed [0006.322] Writing offset failed [0006.325] eeprom_init: EEPROM read failed [0006.329] pm_ids_update: eeprom init failed [0006.333] pm_ids_update: Updating 3,a0, size 256, type 0 [0006.363] pm_ids_update: The pm board id is 3448-0002-400 [0006.370] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0006.377] pm_ids_update: pm id update successful [0006.382] pm_ids_update: Updating 3,ae, size 256, type 0 [0006.412] pm_ids_update: The pm board id is 3449-0000-400 [0006.418] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0006.426] pm_ids_update: pm id update successful [0006.457] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0006.463] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0006.471] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0006.477] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0006.485] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ea:34:98 [0006.492] Plugin Manager: Parse ODM data 0x00094000 [0006.502] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0006.510] Add serial number:1423519040734 as DT property [0006.519] "bpmp" doesn't exist, creating [0006.525] Updated bpmp info to DTB [0006.530] Updated initrd info to DTB [0006.533] "proc-board" doesn't exist, creating [0006.539] Updated board info to DTB [0006.542] "pmu-board" doesn't exist, creating [0006.547] Updated board info to DTB [0006.551] "display-board" doesn't exist, creating [0006.556] Updated board info to DTB [0006.560] "reset" doesn't exist, creating [0006.564] Updated reset info to DTB [0006.568] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 consol [0006.607] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0006.612] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [0006.628] Updated bootarg info to DTB [0006.632] Adding uuid 00000001644612841400000006fd0500 to DT [0006.638] Adding eks info 0 to DT [0006.643] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0006.649] Updated memory info to DTB [0006.658] set vdd_core voltage to 1125 mv [0006.662] setting 'vdd-core' regulator to 1125000 micro volts [0006.682] Found secure-pmc; disable BPMP U-Boot 2016.07-ge6da093be3 (Jun 25 2020 - 21:18:08 -0700) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Failed to get idcodes *** Warning - spi_flash_probe() failed, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Card did not respond to voltage select! ** Bad device mmc 1 ** Hit any key to stop autoboot: 0 Card did not respond to voltage select! switch to partitions #0, OK mmc0(part 0) is current device Failed to mount ext2 filesystem... ** Unrecognized filesystem type ** starting USB... USB0: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 USB error: all controllers failed lowlevel init PCI device eth_rtl8169: unknown chip version, assuming RTL-8169 PCI device: TxConfig = 0x4B100D00 BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 192.168.0.14 (325 ms) *** Warning: no boot file name; using 'C0A8000E.img' Using eth_rtl8169 device TFTP from server 192.168.0.1; our IP address is 192.168.0.14 Filename 'C0A8000E.img'. Load address: 0x83280000 Loading: T T T T T T T CTRL-A Z for help | 115200 8N1 | NOR | Minicom 2.7 | VT102 | Offline | ttyUSB0