[BEGIN] 2021/8/19 15:47:04 [ 16.101137] ERROR: mmcblk0p1 not found [0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-dd84d362) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x51bf4 [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.178] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.198] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.233] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.280] Read PT from (2:0) [0000.296] Using BFS PT to query partitions [0000.301] Loading Tboot-CPU binary [0000.330] Verifying TBC in OdmNonSecureSBK mode [0000.340] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.347] Bootloader downloaded successfully. [0000.351] Downloaded Tboot-CPU binary to 0xa0000258 [0000.356] MAX77620_GPIO5 configured [0000.359] CPU power rail is up [0000.362] CPU clock enabled [0000.366] Performing RAM repair [0000.369] Updating A64 Warmreset Address to 0xa00002e9 [0000.374] BoardID = 3448, SKU = 0x0 [0000.377] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.381] Nano-SD: checking PT table on QSPI ... [0000.385] Loading NvTbootBootloaderDTB [0000.452] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.525] Bootloader DTB Load Address: 0x83000000 [0000.530] BoardID = 3448, SKU = 0x0 [0000.533] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.537] Nano-SD: checking PT table on QSPI ... [0000.541] Loading NvTbootKernelDTB [0000.607] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.680] Kernel DTB Load Address: 0x83100000 [0000.684] BoardID = 3448, SKU = 0x0 [0000.688] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.691] Nano-SD: checking PT table on QSPI ... [0000.698] Loading cboot binary [0000.813] Verifying EBT in OdmNonSecureSBK mode [0000.855] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.862] Bootloader downloaded successfully. [0000.866] BoardID = 3448, SKU = 0x0 [0000.870] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.873] Nano-SD: checking PT table on QSPI ... [0000.878] PT: Partition NCT NOT found ! [0000.882] Warning: Find Partition via PT Failed [0000.886] Next binary entry address: 0x92c00258 [0000.890] BoardId: 3448 [0000.895] Overriding pmu board id with proc board id [0000.900] Display board id is not available [0000.904] BoardID = 3448, SKU = 0x0 [0000.907] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.911] Nano-SD: checking PT table on QSPI ... [0001.016] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.073] /bpmp deleted [0001.075] SC7EntryFw header found loaded at 0xff700000 [0001.270] OVR2 PMIC [0001.272] Bpmp FW successfully loaded [0001.276] BoardID = 3448, SKU = 0x0 [0001.279] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.283] Nano-SD: checking PT table on QSPI ... [0001.288] WB0 init successfully at 0xff780000 [0001.292] Set NvDecSticky Bits [0001.296] GSC2 address ff53fffc value c0edbbcc [0001.302] GSC MC Settings done [0001.305] BoardID = 3448, SKU = 0x0 [0001.308] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.312] Nano-SD: checking PT table on QSPI ... [0001.318] TOS Image length 53680 [0001.321] Monitor size 53680 [0001.324] OS size 0 [0001.339] Secure Os AES-CMAC Verification Success! [0001.343] TOS image cipher info: plaintext [0001.347] Loading and Validation of Secure OS Successful [0001.363] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.368] NvTbootPackSdramParams: start. [0001.373] NvTbootPackSdramParams: done. [0001.377] Tegraboot started after 51774 us [0001.381] Basic modules init took 886372 us [0001.385] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.390] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.396] Next stage binary read took 102860 us [0001.400] Carveout took -126357 us [0001.403] CPU initialization took 495394 us [0001.407] Total time taken by TegraBoot 1358269 us [0001.412] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 11:29:29, Jun 14 2021 ERROR: Error initializing runtime service trusty_fast [0001.534] RamCode = 0 [0001.539] LPDDR4 Training: Read DT: Number of tables = 2 [0001.544] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.557] EMC Training Successful [0001.560] 408000 not found in DVFS table [0001.566] RamCode = 0 [0001.570] DT Write: emc-table@204000 succeeded [0001.575] DT Write: emc-table@1600000 succeeded [0001.579] LPDDR4 Training: Write DT: Number of tables = 2 [0001.626] [0001.627] Debug Init done [0001.630] Marked DTB cacheable [0001.633] Bootloader DTB loaded at 0x83000000 [0001.637] Marked DTB cacheable [0001.640] Kernel DTB loaded at 0x83100000 [0001.644] DeviceTree Init done [0001.657] Pinmux applied successfully [0001.662] gicd_base: 0x50041000 [0001.665] gicc_base: 0x50042000 [0001.668] Interrupts Init done [0001.672] Using base:0x60005090 & irq:208 for tick-timer [0001.677] Using base:0x60005098 for delay-timer [0001.682] platform_init_timer: DONE [0001.685] Timer(tick) Init done [0001.689] osc freq = 38400 khz [0001.693] [0001.694] Welcome to L4T Cboot [0001.697] [0001.698] Cboot Version: 00.00.2018.01-t210-39562017 [0001.703] calling constructors [0001.706] initializing heap [0001.709] initializing threads [0001.712] initializing timers [0001.715] creating bootstrap completion thread [0001.719] top of bootstrap2() [0001.722] CPU: ARM Cortex A57 [0001.725] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.729] initializing platform [0001.737] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.741] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.746] Macronix QSPI chip present [0001.749] SPI device register [0001.752] init boot device [0001.755] allocating memory for boot device(SPI) [0001.759] registering boot device [0001.778] QSPI bdev is already initialized [0001.782] Enable APE clock [0001.784] Un-powergate APE partition [0001.788] of_register: registering tegra_udc to of_hal [0001.793] of_register: registering inv20628-driver to of_hal [0001.799] of_register: registering ads1015-driver to of_hal [0001.804] of_register: registering lp8557-bl-driver to of_hal [0001.810] of_register: registering bq2419x_charger to of_hal [0001.816] of_register: registering bq27441_fuel_gauge to of_hal [0001.827] gpio framework initialized [0001.831] of_register: registering tca9539_gpio to of_hal [0001.836] of_register: registering tca9539_gpio to of_hal [0001.841] of_register: registering i2c_bus_driver to of_hal [0001.847] of_register: registering i2c_bus_driver to of_hal [0001.852] of_register: registering i2c_bus_driver to of_hal [0001.858] pmic framework initialized [0001.862] of_register: registering max77620_pmic to of_hal [0001.867] regulator framework initialized [0001.871] of_register: registering tps65132_bl_driver to of_hal [0001.877] initializing target [0001.883] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.891] board ID = D78, board SKU = 0 [0001.894] Skipping Z3! [0001.899] fixed regulator driver initialized [0001.917] initializing OF layer [0001.920] NCK carveout not present [0001.923] Skipping dts_overrides [0001.928] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.945] I2C Bus Init done [0001.947] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.958] I2C Bus Init done [0001.960] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.971] I2C Bus Init done [0001.973] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.984] I2C Bus Init done [0001.986] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.997] I2C Bus Init done [0001.999] of_children_init: Ops found for compatible string maxim,max77620 [0002.010] max77620_init using irq 118 [0002.015] register 'maxim,max77620' pmic [0002.019] gpio_driver_register: register 'max77620-gpio' driver [0002.025] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.036] I2C Bus Init done [0002.039] NCK carveout not present [0002.049] Find /i2c@7000c000's alias i2c0 [0002.053] get eeprom at 1-a0, size 256, type 0 [0002.062] Find /i2c@7000c500's alias i2c2 [0002.066] get eeprom at 3-a0, size 256, type 0 [0002.070] get eeprom at 3-ae, size 256, type 0 [0002.074] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.080] I2C slave not started [0002.083] I2C write failed [0002.085] Writing offset failed [0002.088] eeprom_init: EEPROM read failed [0002.092] pm_ids_update: eeprom init failed [0002.096] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.127] pm_ids_update: The pm board id is 3448-0000-402 [0002.133] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.142] pm_ids_update: pm id update successful [0002.146] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.176] pm_ids_update: The pm board id is 3449-0000-400 [0002.183] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.191] pm_ids_update: pm id update successful [0002.221] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.227] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.235] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.241] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.249] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3c:ce:0f [0002.255] Plugin Manager: Parse ODM data 0x000a4000 [0002.268] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.282] Find /i2c@7000c000's alias i2c0 [0002.286] get eeprom at 1-a0, size 256, type 0 [0002.295] Find /i2c@7000c500's alias i2c2 [0002.299] get eeprom at 3-a0, size 256, type 0 [0002.303] get eeprom at 3-ae, size 256, type 0 [0002.308] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.313] I2C slave not started [0002.316] I2C write failed [0002.319] Writing offset failed [0002.322] eeprom_init: EEPROM read failed [0002.326] pm_ids_update: eeprom init failed [0002.330] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.360] pm_ids_update: The pm board id is 3448-0000-402 [0002.366] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.373] pm_ids_update: pm id update successful [0002.378] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.408] pm_ids_update: The pm board id is 3449-0000-400 [0002.414] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.421] pm_ids_update: pm id update successful [0002.451] Add serial number:1421021006660 as DT property [0002.459] Applying platform configs [0002.466] platform-init is not present. Skipping [0002.470] calling apps_init() [0002.476] Couldn't find GPT header [0002.481] Proceeding to Cold Boot [0002.484] starting app android_boot_app [0002.488] Device state: unlocked [0002.491] display console init [0002.499] could not find regulator [0002.502] hdmi cable connected [0002.518] edid read success [0002.533] edid rDT entry for leds-pwm not found e[0002.541] ad success [0002.543] width = 640, height = 480, frequency = 25174825 [0002.548] width = 640, height = 480, frequency = 25174825 [0002.554] width = 640, height = 480, frequency = 25174825 [0002.559] width = 640, height = 480, frequency = 25174825 [0002.564] width = 1920, height = 1080, frequency = 148500000 [0002.570] width = 1920, height = 1080, frequency = 174500000 [0002.576] width = 1920, height = 1080, frequency = 148500000 [0002.581] width = 1920, height = 1080, frequency = 148351648 [0002.587] width = 1920, height = 1080, frequency = 148351648 [0002.593] width = 1280, height = 720, frequency = 74175824 [0002.598] width = 1280, height = 720, frequency = 74175824 [0002.604] width = 720, height = 480, frequency = 26973026 [0002.609] width = 720, height = 576, frequency = 26973026 [0002.614] width = 720, height = 480, frequency = 26973026 [0002.620] width = 720, height = 576, frequency = 26973026 [0002.625] width = 640, height = 480, frequency = 25174825 [0002.631] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.638] tmds-config node not found [0002.642] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.657] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.665] could not find regulator [0002.668] could not find regulator [0002.671] could not find regulator [0002.700] using default cmu settings [0002.703] dc_hdmi_enable, starting HDMI initialisation [0002.709] dc_hdmi_enable, HDMI initialisation complete [0002.714] list and configure display window [0002.723] display console init completed [0002.734] subnode volume_up is not found ! [0002.738] subnode back is not found ! [0002.742] subnode volume_down is not found ! [0002.746] subnode menu is not found ! [0002.750] Gpio keyboard init success [0002.830] found decompressor handler: lz4-legacy [0002.845] decompressing blob (type 1)... [0002.915] load_bmp_blob: panelresolution=1080 type=3 [0002.989] decompressor handler not found [0002.993] load_firmware_blob: Firmware blob loaded, entries=2 [0002.999] XUSB blob version 0 size 124416 @ 0x934ae28c [0003.005] -------> se_aes_verify_sbk_clear: 747 [0003.009] se_aes_verify_sbk_clear: Error [0003.013] SE operation failed [0003.016] bl_battery_charging: connected to external power supply [0003.028] device_query_partition_size: failed to open partition spiflash0:MSC ! [0003.036] MSC Partition not found [0003.042] device_query_partition_size: failed to open partition spiflash0:USP ! [0003.049] USP partition read failed! [0003.053] blob_init: blob-partition USP header read failed [0003.058] android_boot Unable to update recovery partition [0003.064] kfs_getpartname: name = LNX [0003.067] Loading kernel from LNX [0003.076] Found 19 BFS partitions in "spiflash0" [0003.396] load kernel from storage [0003.401] decompressor handler not found [0003.666] Successfully loaded kernel and ramdisk images [0003.671] board ID = D78, board SKU = 0 [0003.675] sdmmc node status = okay [0003.679] sdcard instance = 0 [0003.681] sdcard gpio handle 0x5b [0003.685] sdcard gpio pin 0xc9 [0003.688] sdcard gpio flags 0x0 [0003.691] vmmc-supply 0x9e [0003.693] cd_gpio_pin = 201 [0003.696] pin_state = 1 [0003.698] No sdcard [0003.700] SD-card NOT present ... [0003.704] load_and_boot_kernel: SD card not detected! [0003.710] load_bmp_blob: panelresolution=1080 type=3 [0004.205] display bmp image done [0009.210] load_bmp_blob: panelresolution=1080 type=3 [0009.703] display bmp image done [0009.706] NCK carveout not present [0009.709] Skipping dts_overrides [0009.713] NCK carveout not present [0009.722] Find /i2c@7000c000's alias i2c0 [0009.726] get eeprom at 1-a0, size 256, type 0 [0009.735] Find /i2c@7000c500's alias i2c2 [0009.739] get eeprom at 3-a0, size 256, type 0 [0009.743] get eeprom at 3-ae, size 256, type 0 [0009.748] pm_ids_update: Updating 1,a0, size 256, type 0 [0009.753] I2C slave not started [0009.756] I2C write failed [0009.759] Writing offset failed [0009.762] eeprom_init: EEPROM read failed [0009.766] pm_ids_update: eeprom init failed [0009.770] pm_ids_update: Updating 3,a0, size 256, type 0 [0009.800] pm_ids_update: The pm board id is 3448-0000-402 [0009.807] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0009.815] pm_ids_update: pm id update successful [0009.820] pm_ids_update: Updating 3,ae, size 256, type 0 [0009.850] pm_ids_update: The pm board id is 3449-0000-400 [0009.856] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0009.864] pm_ids_update: pm id update successful [0009.894] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0009.900] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0009.908] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0009.914] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0009.922] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3c:ce:0f [0009.929] Plugin Manager: Parse ODM data 0x000a4000 [0009.941] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0009.949] Add serial number:1421021006660 as DT property [0009.958] "bpmp" doesn't exist, creating [0009.964] Updated bpmp info to DTB [0009.969] Updated initrd info to DTB [0009.972] "proc-board" doesn't exist, creating [0009.978] Updated board info to DTB [0009.982] "pmu-board" doesn't exist, creating [0009.988] Updated board info to DTB [0009.991] "display-board" doesn't exist, creating [0009.997] Updated board info to DTB [0010.000] "reset" doesn't exist, creating [0010.005] Updated reset info to DTB [0010.008] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 [0010.048] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0010.053] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0010.066] Updated bootarg info to DTB [0010.070] Adding uuid 00000001642e12c32400000006fe82c0 to DT [0010.076] Adding eks info 0 to DT [0010.081] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0010.087] Updated memory info to DTB [0010.095] set vdd_core voltage to 1075 mv [0010.099] setting 'vdd-core' regulator to 1075000 micro volts [0010.105] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Jun 14 2021 - 11:29:26 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 MMC: no card present Card did not respond to voltage select! starting USB... Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 Bus xusb@70090000: Firmware size 124416 Firmware timestamp: 0x5da88fc3, Version: 50.25 release Register HCSParams1: 9000124 NbrPorts: 9 Starting the controller USB XHCI 1.00 scanning bus xusb@70090000 for devices... 5 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: KIOXIA-E Rev: 0 Prod: XCERIA SATA SSD Type: Hard Disk Capacity: 228936.5 MB = 223.5 GB (468862128 x 512) ... is now current device Scanning usb 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 895 bytes read in 3 ms (291 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7159833 bytes read in 31 ms (220.3 MiB/s) Retrieving file: /boot/Image 34338824 bytes read in 135 ms (242.6 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/sda1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 Retrieving file: /boot/tegra210-p3448-0000-p3449-0000-b00.dtb 245254 bytes read in 3 ms (78 MiB/s) ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083000000, end 000000008303ee05 copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... DT property /chosen/nvidia,bluetooth-mac missing in source; can't copy DT property /chosen/nvidia,wifi-mac missing in source; can't copy DT property /psci/nvidia,system-lp0-disable missing in source; can't copy Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-5486-d4000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Wed May 5 09:31:36 PDT 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29364(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3560360K/4159488K available (15294K kernel code, 2942K rwdata, 6664K rodata, 8576K init, 609K bss, 123992K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009600000 ( 6720 KB) [ 0.000000] .init : 0xffffff8009600000 - 0xffffff8009e60000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e60000 - 0xffffff800a13f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a13f808 - 0xffffff800a1d7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] PLL_RE already enabled. Postponing set full defaults [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.010032] Console: colour dummy device 80x25 [ 0.014688] console [tty0] enabled [ 0.018196] bootconsole [uart8250] disabled [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-5486-d4000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Wed May 5 09:31:36 PDT 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29364(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3560360K/4159488K available (15294K kernel code, 2942K rwdata, 6664K rodata, 8576K init, 609K bss, 123992K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009600000 ( 6720 KB) [ 0.000000] .init : 0xffffff8009600000 - 0xffffff8009e60000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e60000 - 0xffffff800a13f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a13f808 - 0xffffff800a1d7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] PLL_RE already enabled. Postponing set full defaults [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.010032] Console: colour dummy device 80x25 [ 0.014688] console [tty0] enabled [ 0.018196] bootconsole [uart8250] disabled [ 0.022536] kmemleak: Kernel memory leak detector disabled [ 0.022565] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.022588] pid_max: default: 32768 minimum: 301 [ 0.023054] Security Framework initialized [ 0.023280] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.023295] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.024500] ftrace: allocating 47208 entries in 185 pages [ 0.195190] ASID allocator initialised with 65536 entries [ 0.232546] tegra-id: chipid=22117. [ 0.232574] tegra-id: opt_subrevision=0. [ 0.232598] Tegra Speedo/IDDQ fuse revision 4 [ 0.232609] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.232620] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0 [ 0.232632] Tegra: CPU Speedo Value 2069, SoC Speedo Value 1970, GPU Speedo Value 2073 [ 0.232643] Tegra: CPU IDDQ Value 1872, SoC IDDQ Value 2088, GPU IDDQ Value 2645 [ 0.232668] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1 [ 0.232691] DTS File Name: /home/runa/kernel/Linux_for_Tegra/source/public/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.232713] DTB Build time: Aug 16 2021 17:10:10 [ 0.281329] CPU1: Booted secondary processor [411fd071] [ 0.313214] CPU2: Booted secondary processor [411fd071] [ 0.345183] CPU3: Booted secondary processor [411fd071] [ 0.345284] Brought up 4 CPUs [ 0.345342] SMP: Total of 4 processors activated. [ 0.345360] CPU features: detected feature: 32-bit EL0 Support [ 0.345637] CPU: All CPU(s) started at EL2 [ 0.345666] alternatives: patching kernel code [ 0.354175] devtmpfs: initialized [ 0.394550] Initilizing CustomIPI irq domain [ 0.394978] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.395024] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.406612] pinctrl core: initialized pinctrl subsystem [ 0.407261] OS set in device tree is not L4T. [ 0.407730] regulator-dummy: no parameters [ 0.408017] Initializing plugin-manager [ 0.408188] Plugin module not found [ 0.408390] node /plugin-manager/fragement@0 match with board >=3448-0000-100 [ 0.408931] node /plugin-manager/fragment@1 match with board >=3448-0000-101 [ 0.409988] node /plugin-manager/fragement@7 match with odm-data enable-pmic-wdt [ 0.410233] node /plugin-manager/fragement@8 match with odm-data enable-pmic-wdt [ 0.410875] node /plugin-manager/fragement@10 match with board >=3448-0000-300 [ 0.412825] node /plugin-manager/fragement@13 match with board >=3448-0000-300 [ 0.416651] NET: Registered protocol family 16 [ 0.417999] pstore: using zlib compression [ 0.418526] console [pstore-1] enabled [ 0.418541] pstore: Registered ramoops as persistent store backend [ 0.418558] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.437348] cpuidle: using governor menu [ 0.440846] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.442777] vdso: 2 pages (1 code @ ffffff8008f77000, 1 data @ ffffff8009e64000) [ 0.442825] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.445898] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.448422] Serial: AMBA PL011 UART driver [ 0.448929] tegra_powergate_init: DONE [ 0.448962] DTS File Name: /home/runa/kernel/Linux_for_Tegra/source/public/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.448997] DTB Build time: Aug 16 2021 17:10:10 [ 0.451140] Tegra reboot handler registered. [ 0.455772] iommu: Adding device tegra-carveouts to group 0 [ 0.455955] platform tegra-carveouts: domain=ffffffc0f94583d8 allocates as[0]=ffffffc0f946c0a8 [ 0.456350] iommu: Adding device smmu_test to group 1 [ 0.456420] platform smmu_test: domain=ffffffc0f9458618 allocates as[0]=ffffffc0f946c110 [ 0.457290] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.457391] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.457462] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.457486] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.457519] mc-err: mcerr ops are set to t21x [ 0.467955] iommu: Adding device 70090000.xusb to group 2 [ 0.468294] iommu: Adding device 70006000.serial to group 3 [ 0.468372] platform 70006000.serial: domain=ffffffc0f9460cd8 allocates as[0]=ffffffc0f946c178 [ 0.468838] iommu: Adding device 70006040.serial to group 4 [ 0.469116] iommu: Adding device 70006200.serial to group 5 [ 0.469351] iommu: Adding device sound to group 6 [ 0.469423] platform sound: domain=ffffffc0f94d6258 allocates as[0]=ffffffc0f946c1e0 [ 0.470024] iommu: Adding device 7000d400.spi to group 7 [ 0.470302] iommu: Adding device 7000d600.spi to group 8 [ 0.470614] iommu: Adding device 70410000.spi to group 9 [ 0.470953] iommu: Adding device 50000000.host1x to group 10 [ 0.471241] iommu: Adding device 54080000.vi to group 11 [ 0.471637] iommu: Adding device 54600000.isp to group 12 [ 0.471921] iommu: Adding device 54680000.isp to group 13 [ 0.472217] iommu: Adding device tegradc.0 to group 14 [ 0.472281] platform tegradc.0: domain=ffffffc0f94ec198 allocates as[0]=ffffffc0f946c248 [ 0.476476] platform tegradc.0: IOVA linear map 0x0000000092ca9000(800000) [ 0.476886] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.477248] iommu: Adding device tegradc.1 to group 15 [ 0.477313] platform tegradc.1: domain=ffffffc0f94ec3d8 allocates as[0]=ffffffc0f946c2b0 [ 0.481493] platform tegradc.1: IOVA linear map 0x0000000092ca9000(800000) [ 0.481899] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.482188] iommu: Adding device 54340000.vic to group 16 [ 0.482403] iommu: Adding device 544c0000.nvenc to group 17 [ 0.482610] iommu: Adding device 54500000.tsec to group 18 [ 0.482823] iommu: Adding device 54100000.tsecb to group 19 [ 0.483048] iommu: Adding device 54480000.nvdec to group 20 [ 0.483248] iommu: Adding device 54380000.nvjpg to group 21 [ 0.484303] iommu: Adding device 546c0000.i2c to group 22 [ 0.484660] iommu: Adding device 57000000.gpu to group 23 [ 0.484731] platform 57000000.gpu: domain=ffffffc0f95563d8 allocates as[0]=ffffffc0f946c318 [ 0.484806] platform 57000000.gpu: domain=ffffffc0f95563d8 allocates as[1]=ffffffc0f946c380 [ 0.484863] platform 57000000.gpu: domain=ffffffc0f95563d8 allocates as[2]=ffffffc0f946c3e8 [ 0.484918] platform 57000000.gpu: domain=ffffffc0f95563d8 allocates as[3]=ffffffc0f946c450 [ 0.485859] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.485902] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.485929] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [ 0.485947] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.485963] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.537557] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.537589] tegra-pmc: Clear bootloader IO dpd settings [ 0.537620] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.537697] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.538014] iommu: Adding device 70012000.se to group 24 [ 0.538810] iommu: Adding device 7000c000.i2c to group 25 [ 0.539075] iommu: Adding device 7000c400.i2c to group 26 [ 0.539336] iommu: Adding device 7000c500.i2c to group 27 [ 0.539620] iommu: Adding device 7000c700.i2c to group 28 [ 0.539892] iommu: Adding device 7000d000.i2c to group 29 [ 0.540155] iommu: Adding device 7000d100.i2c to group 30 [ 0.540464] iommu: Adding device sdhci-tegra.0 to group 31 [ 0.540538] platform sdhci-tegra.0: domain=ffffffc0f95a1558 allocates as[0]=ffffffc0f946c4b8 [ 0.541466] iommu: Adding device 700d0000.xudc to group 32 [ 0.544637] vdd-ac-bat: 5000 mV [ 0.544999] vdd-5v0-sys: 5000 mV [ 0.545982] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.546048] vdd-5v0-hdmi: 5000 mV [ 0.546458] vdd-1v8-sys: 1800 mV [ 0.546905] vdd-fan: supplied by vdd-5v0-sys [ 0.546960] vdd-fan: 5000 mV [ 0.547388] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.547435] vdd-usb-vbus: 5000 mV [ 0.547952] vdd-usb-vbus2: 5000 mV [ 0.578453] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.582045] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.583219] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.583256] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.583306] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.583739] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.591964] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.592340] SCSI subsystem initialized [ 0.592942] usbcore: registered new interface driver usbfs [ 0.593014] usbcore: registered new interface driver hub [ 0.593105] usbcore: registered new device driver usb [ 0.597594] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.599644] random: fast init done [ 0.600581] vdd-core: 600 <--> 1162 mV at 1075 mV [ 0.601663] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.604562] vdd-ddr-1v1: 1150 mV [ 0.608459] vdd-pre-reg-1v35: 1350 mV [ 0.612512] vdd-1v8: 1800 mV [ 0.616459] avdd-sys-1v2: 1200 mV [ 0.620461] vdd-pex-1v0: 1050 mV [ 0.621143] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.621703] max77620-ldo3: at 3100 mV [ 0.624463] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.625028] max77620-ldo5: at 3100 mV [ 0.628466] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [ 0.632460] avdd-1v05-pll: 1050 mV [ 0.636465] avdd-io-hdmi-dp: 1050 mV [ 0.639178] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.639485] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.639805] max77620 4-003c: max77620 probe successful [ 0.642619] media: Linux media interface: v0.10 [ 0.642695] Linux video capture interface: v2.00 [ 0.643640] pps_core: LinuxPPS API ver. 1 registered [ 0.643667] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.643709] PTP clock support registered [ 0.647077] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.648034] Advanced Linux Sound Architecture Driver Initialized. [ 0.648691] Bluetooth: Core ver 2.22 [ 0.648771] NET: Registered protocol family 31 [ 0.648789] Bluetooth: HCI device and connection manager initialized [ 0.648814] Bluetooth: HCI socket layer initialized [ 0.648834] Bluetooth: L2CAP socket layer initialized [ 0.648873] Bluetooth: SCO socket layer initialized [ 0.650683] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.650721] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.650783] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.650810] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.654563] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.655867] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.655958] vdd-3v3-sys: 3300 mV [ 0.656274] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.661390] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.661898] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.661955] vdd-3v3-sd: 3300 mV [ 0.663008] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.663065] avdd-io-edp-1v05: 1050 mV [ 0.663538] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.663593] vdd-usb-hub-en: 5000 mV [ 0.665041] camchar: rtcpu character device driver loaded [ 0.665824] extcon-gpio-states extcon:extcon@1: Cable state:1, cable id:1 [ 0.667223] clocksource: Switched to clocksource arch_sys_counter [ 0.709246] VFS: Disk quotas dquot_6.6.0 [ 0.709417] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.709927] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.710393] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.710440] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.710685] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.710709] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.710736] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.710784] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.710809] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.710843] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.710864] nvmap_page_pool_init: Total RAM pages: 1008874 [ 0.710881] nvmap_page_pool_init: nvmap page pool size: 126109 pages (492 MB) [ 0.710996] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.711566] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.712401] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.722634] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.723130] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.723581] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.723890] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.724086] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.724389] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.724409] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.724858] NET: Registered protocol family 2 [ 0.725871] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.726111] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.726658] TCP: Hash tables configured (established 32768 bind 32768) [ 0.726837] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.726937] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.727429] NET: Registered protocol family 1 [ 0.728228] RPC: Registered named UNIX socket transport module. [ 0.728251] RPC: Registered udp transport module. [ 0.728267] RPC: Registered tcp transport module. [ 0.728283] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.728582] Trying to unpack rootfs image as initramfs... [ 1.033587] Freeing initrd memory: 6992K [ 1.043823] host1x 50000000.host1x: initialized [ 1.045650] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.049072] audit: initializing netlink subsys (disabled) [ 1.049197] audit: type=2000 audit(0.891:1): initialized [ 1.049998] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.060039] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.061564] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.062386] 9p: Installing v9fs 9p2000 file system support [ 1.065775] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 1.065945] io scheduler noop registered [ 1.066255] io scheduler cfq registered (default) [ 1.069206] gic 702f9000.agic: GIC IRQ controller registered [ 1.072227] iommu: Adding device 702ef000.adsp to group 33 [ 1.081472] iommu: Adding device aconnect@702c0000:adsp_audio to group 34 [ 1.081647] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 1.082278] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x7246c0f [ 1.082308] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 1.084089] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 1.084224] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 1.084342] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 1.084554] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 1.084692] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 1.084799] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 1.084907] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 1.085009] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 1.085119] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 1.085227] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 1.091553] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 1.093369] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 1.095389] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.096666] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 1.097029] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.098269] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.098523] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 1.098813] Adding domain tsec-pd to PM domain host1x-pd [ 1.101296] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 1.102396] tsec 54500000.tsec: initialized [ 1.104048] tsec 54100000.tsecb: initialized [ 1.104790] Adding domain nvdec-pd to PM domain host1x-pd [ 1.108481] nvdec 54480000.nvdec: initialized [ 1.109543] Adding domain vic03-pd to PM domain host1x-pd [ 1.109744] Adding domain msenc-pd to PM domain host1x-pd [ 1.109916] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.114338] falcon 54340000.vic: initialized [ 1.115695] falcon 544c0000.nvenc: initialized [ 1.117117] falcon 54380000.nvjpg: initialized [ 1.121746] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97 [ 1.121818] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.121867] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.121908] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.122021] display board info: id 0x0, fab 0x0 [ 1.122091] generic_infoframe_type: 0x87 [ 1.122241] tegradc tegradc.0: DT parsed successfully [ 1.122296] tegradc tegradc.0: Display dc.ffffff800ab80000 registered with id=0 [ 1.122823] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 1920x1080 (on 0x0mm) pclk=148350781 [ 1.124090] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.124118] tegra_cec 70015000.tegra_cec: probed [ 1.130677] tegradc tegradc.0: probed [ 1.131609] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.138763] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.139927] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check disabled [ 1.139967] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.140372] kfuse 7000fc00.kfuse: initialized [ 1.142099] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.143151] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.144801] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.144850] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.145443] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.147146] vdd-gpu: applied init 1000000uV constraint [ 1.147176] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.147668] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.152769] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.152996] No Device Node present for smmu client: serial8250 !! [ 1.153033] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.153115] iommu: Adding device serial8250 to group 35 [ 1.156698] console [ttyS0] disabled [ 1.156914] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.632225] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.036760] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.143243] tegra_cec 70015000.tegra_cec: Can't find physical addresse. [ 2.143248] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 2.441041] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.443058] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.549279] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.549288] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.549294] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.549299] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.549306] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.559374] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [ 2.559381] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.559390] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit] [ 2.559411] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit] [ 2.559430] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.559440] pci 0000:00:02.0: PCI bridge to [bus 01] [ 2.559446] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.559452] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] [ 2.559860] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 2.559866] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 3.621193] console [ttyS0] enabled [ 3.621795] Console: switching to colour frame buffer device 240x67 [ 3.624496] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 3.624820] serial-tegra 70006200.serial: RX in PIO mode [ 3.624911] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 3.626020] [drm] Initialized [ 3.657371] brd: module loaded [ 3.661249] tegradc tegradc.0: fb registered [ 3.668697] loop: module loaded [ 3.671988] tegra_profiler: version: 1.143, samples/io: 48/28 [ 3.672277] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [ 3.672318] tegradc tegradc.0: hdmi: tmds rate:148351K prod-setting:prod_c_hdmi_75m_150m [ 3.672814] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [ 3.672824] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [ 3.698947] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 3.698951] Extcon AUX1(HDMI) enable [ 3.699939] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 3.700011] tegradc tegradc.1: No lt-data, using default setting [ 3.700040] tegradc tegradc.1: No hpd-gpio in DT [ 3.700072] tegradc tegradc.1: DT parsed successfully [ 3.700127] tegradc tegradc.1: Display dc.ffffff800d500000 registered with id=1 [ 3.701620] tegradc tegradc.1: dpd enable lookup fail:-19 [ 3.705924] tegradc tegradc.1: probed [ 3.735452] tegradc tegradc.0: nominal-pclk:148351648 parent:148350781 div:1.0 pclk:148350781 146868084~161703244 [ 3.766144] tegradc tegradc.1: fb registered [ 3.766238] tegra_profiler: auth: init [ 3.766811] THERMAL EST: found 2 subdevs [ 3.766815] THERMAL EST num_resources: 0 [ 3.766819] [THERMAL EST subdev 0] [ 3.766824] [THERMAL EST subdev 1] [ 3.767138] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 3.767140] THERMAL EST: thz register success. [ 3.767252] THERMAL EST: end of probe, return err: 0 [ 3.767888] sd: No Scsi addr parsed to reserve index [ 3.767909] hisi_sas: driver version v1.6 [ 3.771732] tegra-qspi 70410000.spi: Prod settings list not found [ 3.778202] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes) [ 3.778209] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0 [ 3.786344] libphy: Fixed MDIO Bus: probed [ 3.787277] tun: Universal TUN/TAP device driver, 1.6 [ 3.787279] tun: (C) 1999-2004 Max Krasnyansky [ 3.787882] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 3.787884] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.787921] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 3.787922] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.787960] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 3.787961] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.787996] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 3.787998] Copyright(c) 1999 - 2017 Intel Corporation. [ 3.792664] r8168 0000:01:00.0: enabling device (0000 -> 0003) [ 3.792683] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 3.806751] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 3.806813] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 48:b0:2d:3c:ce:0f from device tree [ 3.807240] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 3.807271] r8168 Copyright (C) 2017 Realtek NIC software team [ 3.807271] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 3.807271] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 3.807676] PPP generic driver version 2.4.2 [ 3.807809] PPP BSD Compression module registered [ 3.807812] PPP Deflate Compression module registered [ 3.807826] PPP MPPE Compression module registered [ 3.807830] NET: Registered protocol family 24 [ 3.807878] usbcore: registered new interface driver r8152 [ 3.807919] usbcore: registered new interface driver asix [ 3.807958] usbcore: registered new interface driver ax88179_178a [ 3.807991] usbcore: registered new interface driver cdc_ether [ 3.808023] usbcore: registered new interface driver net1080 [ 3.808055] usbcore: registered new interface driver cdc_subset [ 3.808086] usbcore: registered new interface driver zaurus [ 3.808133] usbcore: registered new interface driver cdc_ncm [ 3.808264] VFIO - User Level meta-driver version: 0.3 [ 3.809220] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.809230] ehci-pci: EHCI PCI platform driver [ 3.809266] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.809273] ohci-pci: OHCI PCI platform driver [ 3.809309] ohci-platform: OHCI generic platform driver [ 3.811172] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 3.811775] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 3.812826] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f97ce800 id [ 3.814261] usbcore: registered new interface driver uas [ 3.814312] usbcore: registered new interface driver usb-storage [ 3.814379] usbcore: registered new interface driver usbserial [ 3.815244] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release [ 3.815273] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.815290] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 3.815997] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 3.816034] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 3.816183] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.816188] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.816193] usb usb1: Product: xHCI Host Controller [ 3.816196] usb usb1: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 3.816200] usb usb1: SerialNumber: 70090000.xusb [ 3.816620] hub 1-0:1.0: USB hub found [ 3.816660] hub 1-0:1.0: 5 ports detected [ 3.817134] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.817144] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 3.817212] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.817303] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 3.817308] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.817312] usb usb2: Product: xHCI Host Controller [ 3.817315] usb usb2: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 3.817319] usb usb2: SerialNumber: 70090000.xusb [ 3.817671] hub 2-0:1.0: USB hub found [ 3.817701] hub 2-0:1.0: 4 ports detected [ 3.818335] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 3.818340] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 3.820052] tegra-xudc-new 700d0000.xudc: device count: 1 [ 3.821015] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 3.821024] tegra-xudc-new 700d0000.xudc: vbus state: 1 [ 3.821034] tegra-xudc-new 700d0000.xudc: device mode on: 0 [ 3.821052] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0 [ 3.821069] tegra-xudc-new 700d0000.xudc: active: 0 => 1 [ 3.821519] mousedev: PS/2 mouse device common for all mice [ 3.821587] usbcore: registered new interface driver xpad [ 3.919324] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 3.919582] usb usb2: usb_suspend_both: status 0 [ 4.024469] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 4.037756] rtc rtc1: alarm rtc device [ 4.037768] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 4.037786] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 4.038166] i2c /dev entries driver [ 4.039686] i2c i2c-6: Added multiplexed i2c bus 7 [ 4.040034] i2c i2c-6: Added multiplexed i2c bus 8 [ 4.040039] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 4.040636] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [ 4.064548] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 4.064620] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 4.064689] imx219 7-0010: board setup failed [ 4.064738] imx219: probe of 7-0010 failed with error -121 [ 4.065155] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [ 4.090823] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 4.090895] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 4.090951] imx219 8-0010: board setup failed [ 4.091000] imx219: probe of 8-0010 failed with error -121 [ 4.097980] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 4.144682] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 4.144687] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 4.144990] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.145002] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 4.145009] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 4.145137] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.145145] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 4.145151] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 4.145299] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.145307] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 4.145311] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 4.145491] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 4.146010] tegra_aotag tegra-aotag: Registering sensor 0 [ 4.146055] tegra_aotag tegra-aotag: Invalid temp readout [ 4.146075] tegra_aotag tegra-aotag: Invalid temp readout [ 4.146091] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 4.146099] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 4.146850] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.146864] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 4.147011] tegra_aotag tegra-aotag: Invalid temp readout [ 4.147033] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 4.147244] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 4.147405] parse_throttle_dt_data: Num cap clks = 6 [ 4.147409] parse_throttle_dt_data: clk=cclk_g type=2 [ 4.147415] parse_throttle_dt_data: clk=gpu type=4 [ 4.147437] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 4.147455] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 4.147474] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 4.147477] parse_throttle_dt_data: clk=emc type=3 [ 4.153006] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.153098] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.153211] tegra_throttle_probe: probe successful. #cdevs=4 [ 4.153772] FAN dev name: pwm-fan [ 4.153814] FAN:gpio request success. [ 4.153866] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 4.154093] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 4.154209] pwm_fan_driver pwm-fan: fan tach request irq success [ 4.154215] pwm_fan_driver pwm-fan: tach period: 1000 [ 4.154291] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 4.154297] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 4.154301] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 4.154305] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 4.154309] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 4.154312] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 4.154316] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 4.154320] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 4.154324] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 4.154328] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 4.189813] device-mapper: uevent: version 1.0.3 [ 4.190205] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 4.192989] tegra210-cpufreq cpufreq: probe()...completed [ 4.193731] sdhci: Secure Digital Host Controller Interface driver [ 4.193733] sdhci: Copyright(c) Pierre Ossman [ 4.193734] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.194213] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 4.194578] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 4.194703] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300 [ 4.197565] tegra-se 70012000.se: tegra_se_probe: complete [ 4.198055] hidraw: raw HID events driver (C) Jiri Kosina [ 4.199148] usbcore: registered new interface driver usbhid [ 4.199150] usbhid: USB HID core driver [ 4.218071] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411 [ 4.218075] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.218077] usb 1-2: Product: 4-Port USB 2.1 Hub [ 4.218079] usb 1-2: Manufacturer: Generic [ 4.225902] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 4.226090] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 4.228035] nvpmodel: initialized successfully [ 4.229268] usbcore: registered new interface driver snd-usb-audio [ 4.229333] No Device Node present for smmu client: snd-soc-dummy !! [ 4.229337] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 4.229355] iommu: Adding device snd-soc-dummy to group 36 [ 4.232259] hub 1-2:1.0: USB hub found [ 4.237036] hub 1-2:1.0: 4 ports detected [ 4.241545] OPE platform probe [ 4.241628] OPE platform probe successful [ 4.241654] OPE platform probe [ 4.241731] OPE platform probe successful [ 4.251526] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 4.264602] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 4.264728] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 4.264858] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 4.264978] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 4.265102] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 4.265223] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 4.265343] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 4.265466] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 4.265583] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 4.265706] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 4.277422] u32 classifier [ 4.277424] Actions configured [ 4.277497] Initializing XFRM netlink socket [ 4.278199] NET: Registered protocol family 10 [ 4.278886] NET: Registered protocol family 17 [ 4.278897] NET: Registered protocol family 15 [ 4.278968] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.279017] Bluetooth: RFCOMM socket layer initialized [ 4.279025] Bluetooth: RFCOMM ver 1.11 [ 4.279029] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.279033] Bluetooth: HIDP socket layer initialized [ 4.279050] 9pnet: Installing 9P2000 support [ 4.279085] Key type dns_resolver registered [ 4.279769] Registered cp15_barrier emulation handler [ 4.279794] Registered setend emulation handler [ 4.280901] registered taskstats version 1 [ 4.281481] Adding domain ve2-pd to PM domain host1x-pd [ 4.281729] Adding domain ve-pd to PM domain host1x-pd [ 4.313752] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.382609] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411 [ 4.382613] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.382616] usb 2-1: Product: 4-Port USB 3.1 Hub [ 4.382618] usb 2-1: Manufacturer: Generic [ 4.413053] hub 2-1:1.0: USB hub found [ 4.420602] hub 2-1:1.0: 4 ports detected [ 4.619286] usb 1-2.3: new low-speed USB device number 3 using tegra-xusb [ 4.686036] usb 1-2.3: New USB device found, idVendor=413c, idProduct=301a [ 4.686039] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.686042] usb 1-2.3: Product: Dell MS116 USB Optical Mouse [ 4.686044] usb 1-2.3: Manufacturer: PixArt [ 4.713015] input: PixArt Dell MS116 USB Optical Mouse as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.0/0003:413C:301A.0001/input/input1 [ 4.713442] hid-generic 0003:413C:301A.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt Dell MS116 USB Optical Mouse] on usb-70090000.xusb-2.3/input0 [ 4.871541] usb 2-1.2: new SuperSpeed USB device number 3 using tegra-xusb [ 4.949947] usb 2-1.2: New USB device found, idVendor=174c, idProduct=235c [ 4.949951] usb 2-1.2: New USB device strings: Mfr=2, Product=3, SerialNumber=1 [ 4.949953] usb 2-1.2: Product: Ugreen Storage Device [ 4.949956] usb 2-1.2: Manufacturer: Ugreen [ 4.949958] usb 2-1.2: SerialNumber: 20D11E802143 [ 4.950576] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 4.971186] scsi host0: uas [ 4.972216] scsi 0:0:0:0: Direct-Access KIOXIA-E XCERIA SATA SSD 0 PQ: 0 ANSI: 6 [ 5.020005] sd 0:0:0:0: [sda] 468862128 512-byte logical blocks: (240 GB/224 GiB) [ 5.021016] sd 0:0:0:0: [sda] Write Protect is off [ 5.021363] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.021854] sd 0:0:0:0: [sda] Optimal transfer size 33553920 bytes [ 5.026468] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 5.026472] GPT:62333951 != 468862127 [ 5.026473] GPT:Alternate GPT header not at the end of the disk. [ 5.026474] GPT:62333951 != 468862127 [ 5.026476] GPT: Use GNU Parted to correct GPT errors. [ 5.026497] sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 [ 5.029426] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.311333] tegradc tegradc.0: blank - powerdown [ 5.314408] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 5.314411] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 5.314416] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 5.315551] isp 54600000.isp: initialized [ 5.316330] isp 54680000.isp: initialized [ 5.326719] last reset is due to power on reset [ 5.326722] KERNEL: PMC reset status reg: 0x0 [ 5.326785] BL: PMC reset status reg: 0x0 [ 5.326787] BL: PMIC poweroff Event Recorder: 0x40 [ 5.343559] clk_cbus_recalc_rate: no gbus parent [ 5.343563] clk_cbus_round_rate: no gbus parent [ 5.343564] clk_cbus_round_rate: no gbus parent [ 5.343570] clk_cbus_recalc_rate: no gbus parent [ 5.343665] clk_cbus_recalc_rate: no gbus parent [ 5.343668] clk_cbus_round_rate: no gbus parent [ 5.343669] clk_cbus_round_rate: no gbus parent [ 5.343672] clk_cbus_recalc_rate: no gbus parent [ 5.343685] tegra_dvfs: GPU-cap: registered [ 5.343745] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 5.343747] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled [ 5.343749] tegra dvfs: vdd-gpu: nominal 1058mV, offset 708000uV, step 10000uV, scaling enabled [ 5.345574] tegra_dvfs: vdd-gpu-vts: registered [ 5.346245] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 5.346792] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 5.347289] input: gpio-keys as /devices/gpio-keys/input/input2 [ 5.359087] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 5.359089] Extcon AUX1(HDMI) disable [ 5.379917] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:00:22 UTC (946688422) [ 5.380967] vi 54080000.vi: vi_probe: ++ [ 5.383667] vi 54080000.vi: initialized [ 5.385913] vi 54080000.vi: subdev nvcsi--2 bound [ 5.386018] vi 54080000.vi: subdev nvcsi--1 bound [ 5.386848] Disable partitions left on by BL [ 5.386850] disb [ 5.386888] bwmgr: missing cdev-type property [ 5.386976] tegradc tegradc.0: unblank [ 5.386981] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.386986] DRAM derating cdev registered. [ 5.387987] ALSA device list: [ 5.387990] #0: tegra-hda at 0x70038000 irq 83 [ 5.387991] #1: tegra-snd-t210ref-mobile-rt565x [ 5.423299] tegradc tegradc.0: nominal-pclk:148500000 parent:148500000 div:1.0 pclk:148500000 147015000~161865000 [ 5.423347] tegradc tegradc.0: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_75m_150m [ 5.424338] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 5.459161] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 5.459163] Extcon AUX1(HDMI) enable [ 5.474582] tegradc tegradc.0: sync windows ret = 247 [ 5.849367] tegradc tegradc.1: blank - powerdown [ 5.855785] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 5.855787] Extcon DP: HPD disabled [ 5.855790] hpd: hpd_switch 0 [ 5.855793] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 5.855802] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 5.855806] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 5.899733] extcon-disp-state extcon:disp-state: cable 51 state 1 [ 5.899735] Extcon HDMI: HPD enabled [ 5.899746] tegradc tegradc.0: hdmi: plugged [ 5.922138] Freeing unused kernel memory: 8576K [ 5.952986] Root device found: mmcblk0p1 [ 16.114565] ERROR: mmcblk0p1 not found [ 28.315280] random: crng init done [ 35.963429] vdd-fan: disabling [ 35.968253] vdd-usb-vbus: disabling [ 35.973525] vdd-usb-vbus2: disabling [ 35.978833] vddio-sdmmc3-ap: disabling [ 35.984376] vdd-3v3-sd: disabling [ 35.989358] avdd-io-edp-1v05: disabling [ 35.994829] vdd-usb-hub-en: disabling