[0000.159] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb) [0000.164] Processing in cold boot mode Bootloader 2 [0000.169] A02 Bootrom Patch rev = 1023 [0000.173] Power-up reason: software reset [0000.176] No Battery Present [0000.179] pmic max77620 reset reason [0000.182] pmic max77620 NVERC : 0x0 [0000.186] RamCode = 0 [0000.188] Platform has DDR4 type RAM [0000.191] max77620 disabling SD1 Remote Sense [0000.195] Setting DDR voltage to 1125mv [0000.199] Serial Number of Pmic Max77663: 0x2f13eb [0000.207] Entering ramdump check [0000.210] Get RamDumpCarveOut = 0x0 [0000.213] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.219] Last reboot was clean, booting normally! [0000.223] Sdram initialization is successful [0000.227] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.233] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.239] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.245] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.251] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.257] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.263] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.268] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.285] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.291] Platform-DebugCarveout: 0 [0000.294] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.300] Non secure mode, and RB not enabled. [0000.304] BoardID = 3448, SKU = 0x0 [0000.307] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.311] Nano-SD: checking PT table on QSPI ... [0000.315] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.321] Read PT from (2:0) [0000.352] PT crc32 and magic check passed. [0000.356] Using BFS PT to query partitions [0000.361] Loading Tboot-CPU binary [0000.390] Verifying TBC in OdmNonSecureSBK mode [0000.400] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.407] Bootloader downloaded successfully. [0000.411] Downloaded Tboot-CPU binary to 0xa0000258 [0000.416] MAX77620_GPIO5 configured [0000.419] CPU power rail is up [0000.422] CPU clock enabled [0000.426] Performing RAM repair [0000.429] Updating A64 Warmreset Address to 0xa00002e9 [0000.434] BoardID = 3448, SKU = 0x0 [0000.437] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.441] Nano-SD: checking PT table on QSPI ... [0000.445] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.451] Loading NvTbootBootloaderDTB [0000.518] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.589] Bootloader DTB Load Address: 0x83000000 [0000.594] BoardID = 3448, SKU = 0x0 [0000.597] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.601] Nano-SD: checking PT table on QSPI ... [0000.605] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.611] Loading NvTbootKernelDTB [0000.677] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.749] Kernel DTB Load Address: 0x83100000 [0000.753] BoardID = 3448, SKU = 0x0 [0000.756] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.760] Nano-SD: checking PT table on QSPI ... [0000.764] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.772] Loading cboot binary [0000.888] Verifying EBT in OdmNonSecureSBK mode [0000.930] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.937] Bootloader downloaded successfully. [0000.941] BoardID = 3448, SKU = 0x0 [0000.944] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.948] Nano-SD: checking PT table on QSPI ... [0000.952] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.958] PT: Partition NCT NOT found ! [0000.962] Warning: Find Partition via PT Failed [0000.966] Next binary entry address: 0x92c00258 [0000.971] BoardId: 3448 [0000.975] Overriding pmu board id with proc board id [0000.980] Display board id is not available [0000.984] BoardID = 3448, SKU = 0x0 [0000.988] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.992] Nano-SD: checking PT table on QSPI ... [0000.996] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.102] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.158] /bpmp deleted [0001.161] SC7EntryFw header found loaded at 0xff700000 [0001.348] OVR2 PMIC [0001.350] Bpmp FW successfully loaded [0001.354] BoardID = 3448, SKU = 0x0 [0001.357] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.361] Nano-SD: checking PT table on QSPI ... [0001.365] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.372] WB0 init successfully at 0xff780000 [0001.376] Verifying NvTbootWb0 in OdmNonSecureSBK mode [0001.382] Set NvDecSticky Bits [0001.385] GSC2 address ff53fffc value c0edbbcc [0001.391] GSC MC Settings done [0001.394] BoardID = 3448, SKU = 0x0 [0001.398] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.401] Nano-SD: checking PT table on QSPI ... [0001.406] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.413] TOS Image length 53680 [0001.416] Monitor size 53680 [0001.419] OS size 0 [0001.434] Secure Os AES-CMAC Verification Success! [0001.438] TOS image cipher info: plaintext [0001.442] Loading and Validation of Secure OS Successful [0001.458] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.463] NvTbootPackSdramParams: start. [0001.468] NvTbootPackSdramParams: done. [0001.472] Tegraboot started after 86977 us [0001.476] Basic modules init took 939617 us [0001.480] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.485] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.491] Next stage binary read took 102860 us [0001.495] Carveout took -132463 us [0001.498] CPU initialization took 510364 us [0001.502] Total time taken by TegraBoot 1420378 us [0001.507] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:09:37, Jul 26 2021 ERROR: Error initializing runtime service trusty_fast [0001.629] RamCode = 0 [0001.634] LPDDR4 Training: Read DT: Number of tables = 2 [0001.639] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.651] EMC Training Successful [0001.654] 408000 not found in DVFS table [0001.661] RamCode = 0 [0001.664] DT Write: emc-table@204000 succeeded [0001.670] DT Write: emc-table@1600000 succeeded [0001.674] LPDDR4 Training: Write DT: Number of tables = 2 [0001.723] [0001.724] Debug Init done [0001.727] Marked DTB cacheable [0001.730] Bootloader DTB loaded at 0x83000000 [0001.734] Marked DTB cacheable [0001.737] Kernel DTB loaded at 0x83100000 [0001.741] DeviceTree Init done [0001.754] Pinmux applied successfully [0001.759] gicd_base: 0x50041000 [0001.762] gicc_base: 0x50042000 [0001.765] Interrupts Init done [0001.769] Using base:0x60005090 & irq:208 for tick-timer [0001.774] Using base:0x60005098 for delay-timer [0001.779] platform_init_timer: DONE [0001.782] Timer(tick) Init done [0001.786] osc freq = 38400 khz [0001.790] [0001.791] Welcome to L4T Cboot [0001.794] [0001.795] Cboot Version: 00.00.2018.01-t210-c952b4e6 [0001.800] calling constructors [0001.803] initializing heap [0001.806] initializing threads [0001.809] initializing timers [0001.811] creating bootstrap completion thread [0001.816] top of bootstrap2() [0001.819] CPU: ARM Cortex A57 [0001.822] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.826] initializing platform [0001.834] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.838] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.843] Macronix QSPI chip present [0001.846] SPI device register [0001.849] init boot device [0001.852] allocating memory for boot device(SPI) [0001.856] registering boot device [0001.865] QSPI bdev is already initialized [0001.868] Enable APE clock [0001.871] Un-powergate APE partition [0001.875] of_register: registering tegra_udc to of_hal [0001.880] of_register: registering inv20628-driver to of_hal [0001.885] of_register: registering ads1015-driver to of_hal [0001.891] of_register: registering lp8557-bl-driver to of_hal [0001.897] of_register: registering bq2419x_charger to of_hal [0001.902] of_register: registering bq27441_fuel_gauge to of_hal [0001.914] gpio framework initialized [0001.917] of_register: registering tca9539_gpio to of_hal [0001.922] of_register: registering tca9539_gpio to of_hal [0001.928] of_register: registering i2c_bus_driver to of_hal [0001.933] of_register: registering i2c_bus_driver to of_hal [0001.939] of_register: registering i2c_bus_driver to of_hal [0001.944] pmic framework initialized [0001.948] of_register: registering max77620_pmic to of_hal [0001.953] regulator framework initialized [0001.957] of_register: registering tps65132_bl_driver to of_hal [0001.963] initializing target [0001.969] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.977] board ID = D78, board SKU = 0 [0001.981] Skipping Z3! [0001.985] fixed regulator driver initialized [0002.003] initializing OF layer [0002.006] NCK carveout not present [0002.009] Skipping dts_overrides [0002.013] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.030] I2C Bus Init done [0002.032] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.042] I2C Bus Init done [0002.045] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.055] I2C Bus Init done [0002.058] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.068] I2C Bus Init done [0002.071] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.081] I2C Bus Init done [0002.084] of_children_init: Ops found for compatible string maxim,max77620 [0002.094] max77620_init using irq 118 [0002.099] register 'maxim,max77620' pmic [0002.103] gpio_driver_register: register 'max77620-gpio' driver [0002.109] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.120] I2C Bus Init done [0002.123] NCK carveout not present [0002.132] Find /i2c@7000c000's alias i2c0 [0002.136] get eeprom at 1-a0, size 256, type 0 [0002.146] Find /i2c@7000c500's alias i2c2 [0002.150] get eeprom at 3-a0, size 256, type 0 [0002.154] get eeprom at 3-ae, size 256, type 0 [0002.158] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.164] I2C slave not started [0002.167] I2C write failed [0002.169] Writing offset failed [0002.172] eeprom_init: EEPROM read failed [0002.176] pm_ids_update: eeprom init failed [0002.180] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.211] pm_ids_update: The pm board id is 3448-0000-400 [0002.217] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.226] pm_ids_update: pm id update successful [0002.230] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.260] eeprom_init: EEPROM incompatible version found [0002.266] pm_ids_update: eeprom init failed [0002.295] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.301] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.309] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.315] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.323] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:30:b5 [0002.330] Plugin Manager: Parse ODM data 0x000a4000 [0002.342] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.356] Find /i2c@7000c000's alias i2c0 [0002.360] get eeprom at 1-a0, size 256, type 0 [0002.369] Find /i2c@7000c500's alias i2c2 [0002.373] get eeprom at 3-a0, size 256, type 0 [0002.377] get eeprom at 3-ae, size 256, type 0 [0002.382] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.387] I2C slave not started [0002.390] I2C write failed [0002.392] Writing offset failed [0002.396] eeprom_init: EEPROM read failed [0002.399] pm_ids_update: eeprom init failed [0002.404] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.434] pm_ids_update: The pm board id is 3448-0000-400 [0002.440] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.447] pm_ids_update: pm id update successful [0002.451] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.481] eeprom_init: EEPROM incompatible version found [0002.487] pm_ids_update: eeprom init failed [0002.517] Add serial number:1423219108119 as DT property [0002.524] Applying platform configs [0002.531] platform-init is not present. Skipping [0002.535] calling apps_init() [0002.541] Couldn't find GPT header [0002.546] Proceeding to Cold Boot [0002.549] starting app android_boot_app [0002.553] Device state: unlocked [0002.556] display console init [0002.564] could not find regulator [0002.567] hdmi cable connected [0002.583] edid read success [0002.598] edid read success [0002.600] DT entry for leds-pwm not found w[0002.608] idth = 640, height = 480, frequency = 25174825 [0002.613] width = 640, height = 480, frequency = 25174825 [0002.618] width = 1920, height = 1080, frequency = 138500000 [0002.624] width = 1680, height = 1050, frequency = 146250000 [0002.630] width = 1280, height = 720, frequency = 74250000 [0002.635] width = 1280, height = 720, frequency = 74175824 [0002.641] width = 720, height = 480, frequency = 26973026 [0002.646] width = 720, height = 480, frequency = 26973026 [0002.651] width = 1920, height = 1080, frequency = 74175824 [0002.657] width = 1920, height = 1080, frequency = 74175824 [0002.662] width = 1920, height = 1080, frequency = 148351648 [0002.668] width = 720, height = 576, frequency = 26973026 [0002.673] width = 1280, height = 720, frequency = 74175824 [0002.679] width = 720, height = 576, frequency = 26973026 [0002.684] width = 1920, height = 1080, frequency = 148351648 [0002.690] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.698] tmds-config node not found [0002.702] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.716] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.724] could not find regulator [0002.727] could not find regulator [0002.731] could not find regulator [0002.759] using default cmu settings [0002.763] dc_hdmi_enable, starting HDMI initialisation [0002.769] dc_hdmi_enable, HDMI initialisation complete [0002.774] list and configure display window [0002.782] display console init completed [0002.793] subnode volume_up is not found ! [0002.797] subnode back is not found ! [0002.801] subnode volume_down is not found ! [0002.805] subnode menu is not found ! [0002.809] Gpio keyboard init success [0002.889] found decompressor handler: lz4-legacy [0002.904] decompressing blob (type 1)... [0002.973] load_bmp_blob: panelresolution=1080 type=3 [0003.049] decompressor handler not found [0003.053] load_firmware_blob: Firmware blob loaded, entries=2 [0003.059] XUSB blob version 0 size 126464 @ 0x934ae28c [0003.065] -------> se_aes_verify_sbk_clear: 747 [0003.069] se_aes_verify_sbk_clear: Error [0003.073] SE operation failed [0003.076] bl_battery_charging: connected to external power supply [0003.088] device_query_partition_size: failed to open partition spiflash0:MSC ! [0003.095] MSC Partition not found [0003.102] device_query_partition_size: failed to open partition spiflash0:USP ! [0003.109] USP partition read failed! [0003.112] blob_init: blob-partition USP header read failed [0003.118] android_boot Unable to update recovery partition [0003.123] kfs_getpartname: name = LNX [0003.127] Loading kernel from LNX [0003.136] Found 19 BFS partitions in "spiflash0" [0003.461] load kernel from storage [0003.466] decompressor handler not found [0003.736] Successfully loaded kernel and ramdisk images [0003.741] board ID = D78, board SKU = 0 [0003.746] sdmmc node status = okay [0003.749] sdcard instance = 0 [0003.752] sdmmc cd-inverted [0003.755] sdcard gpio handle 0x5b [0003.758] sdcard gpio pin 0xc9 [0003.761] sdcard gpio flags 0x0 [0003.764] vmmc-supply 0x9d [0003.767] cd_gpio_pin = 201 [0003.769] pin_state = 0 [0003.772] Found sdcard [0003.774] SD-card IS present ... [0003.777] load_and_boot_kernel: SD card detected OK [0003.783] load_bmp_blob: panelresolution=1080 type=3 [0004.277] display bmp image done [0004.280] NCK carveout not present [0004.283] Skipping dts_overrides [0004.286] NCK carveout not present [0004.296] Find /i2c@7000c000's alias i2c0 [0004.300] get eeprom at 1-a0, size 256, type 0 [0004.308] Find /i2c@7000c500's alias i2c2 [0004.312] get eeprom at 3-a0, size 256, type 0 [0004.317] get eeprom at 3-ae, size 256, type 0 [0004.321] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.326] I2C slave not started [0004.329] I2C write failed [0004.332] Writing offset failed [0004.335] eeprom_init: EEPROM read failed [0004.339] pm_ids_update: eeprom init failed [0004.343] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.373] pm_ids_update: The pm board id is 3448-0000-400 [0004.380] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0004.388] pm_ids_update: pm id update successful [0004.393] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.423] eeprom_init: EEPROM incompatible version found [0004.428] pm_ids_update: eeprom init failed [0004.458] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.464] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0004.472] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.478] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0004.486] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:30:b5 [0004.492] Plugin Manager: Parse ODM data 0x000a4000 [0004.504] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0004.513] Add serial number:1423219108119 as DT property [0004.522] "bpmp" doesn't exist, creating [0004.527] Updated bpmp info to DTB [0004.532] Updated initrd info to DTB [0004.535] "proc-board" doesn't exist, creating [0004.542] Updated board info to DTB [0004.545] "pmu-board" doesn't exist, creating [0004.551] Updated board info to DTB [0004.554] "display-board" doesn't exist, creating [0004.560] Updated board info to DTB [0004.563] "reset" doesn't exist, creating [0004.568] Updated reset info to DTB [0004.572] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 [0004.611] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.616] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0004.629] Updated bootarg info to DTB [0004.633] Adding uuid 000000016445b5071800000010fe8440 to DT [0004.639] Adding eks info 0 to DT [0004.644] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.650] Updated memory info to DTB [0004.658] set vdd_core voltage to 1125 mv [0004.662] setting 'vdd-core' regulator to 1125000 micro volts [0004.668] Found secure-pmc; disable BPMP U-Boot 2020.04-g46e4604c78 (Jul 26 2021 - 12:09:42 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 1425 bytes read in 29 ms (47.9 KiB/s) L4T boot options 1: primary kernel 2: PE020_CTP_HDMI_WORK 3: PE020S1 Enter choice: 3: PE020S1 Retrieving file: /boot/initrd 7160133 bytes read in 338 ms (20.2 MiB/s) Retrieving file: /boot/Image 34684936 bytes read in 1524 ms (21.7 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 Retrieving file: /boot/dtb/PE020S1.dtb 237488 bytes read in 31 ms (7.3 MiB/s) ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083000000, end 000000008303cfaf copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... DT property /chosen/nvidia,bluetooth-mac missing in source; can't copy DT property /chosen/nvidia,wifi-mac missing in source; can't copy DT property /psci/nvidia,system-lp0-disable missing in source; can't copy Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-tegra (uni@uni-Z370P-D3) (gcc version 7.5.0 (Linaro GCC 7.5-2019.12) ) #6 SMP PREEMPT Tue Nov 30 15:05:54 CET 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57624 r8192 d32488 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29864(91%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3560084K/4159488K available (15422K kernel code, 2960K rwdata, 6816K rodata, 8640K init, 612K bss, 124268K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f90000 ( 15424 KB) [ 0.000000] .rodata : 0xffffff8008f90000 - 0xffffff8009640000 ( 6848 KB) [ 0.000000] .init : 0xffffff8009640000 - 0xffffff8009eb0000 ( 8640 KB) [ 0.000000] .data : 0xffffff8009eb0000 - 0xffffff800a194008 ( 2961 KB) [ 0.000000] .bss : 0xffffff800a194008 - 0xffffff800a22d1f4 ( 613 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.009933] Console: colour dummy device 80x25 [ 0.014588] console [tty0] enabled [ 0.018107] bootconsole [uart8250] disabled [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-tegra (uni@uni-Z370P-D3) (gcc version 7.5.0 (Linaro GCC 7.5-2019.12) ) #6 SMP PREEMPT Tue Nov 30 15:05:54 CET 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57624 r8192 d32488 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29864(91%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3560084K/4159488K available (15422K kernel code, 2960K rwdata, 6816K rodata, 8640K init, 612K bss, 124268K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f90000 ( 15424 KB) [ 0.000000] .rodata : 0xffffff8008f90000 - 0xffffff8009640000 ( 6848 KB) [ 0.000000] .init : 0xffffff8009640000 - 0xffffff8009eb0000 ( 8640 KB) [ 0.000000] .data : 0xffffff8009eb0000 - 0xffffff800a194008 ( 2961 KB) [ 0.000000] .bss : 0xffffff800a194008 - 0xffffff800a22d1f4 ( 613 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.009933] Console: colour dummy device 80x25 [ 0.014588] console [tty0] enabled [ 0.018107] bootconsole [uart8250] disabled [ 0.022432] kmemleak: Kernel memory leak detector disabled [ 0.022458] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.022480] pid_max: default: 32768 minimum: 301 [ 0.022941] Security Framework initialized [ 0.023172] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.023188] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.024361] ftrace: allocating 47223 entries in 185 pages [ 0.194475] ASID allocator initialised with 65536 entries [ 0.232112] tegra-id: chipid=22117. [ 0.232141] tegra-id: opt_subrevision=0. [ 0.232163] Tegra Speedo/IDDQ fuse revision 4 [ 0.232173] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.232184] Tegra: CPU Process ID 0, SoC Process ID 0, GPU Process ID 0 [ 0.232195] Tegra: CPU Speedo Value 1998, SoC Speedo Value 1913, GPU Speedo Value 2006 [ 0.232205] Tegra: CPU IDDQ Value 1292, SoC IDDQ Value 1520, GPU IDDQ Value 1755 [ 0.232230] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 0 [ 0.232253] DTS File Name: /home/uni/Nvidia_Jetson/Jetson_Linux_R32_6_1/Source/Linux_for_Tegra/source/public/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.232285] DTB Build time: Dec 4 2021 12:56:32 [ 0.281348] CPU1: Booted secondary processor [411fd071] [ 0.313234] CPU2: Booted secondary processor [411fd071] [ 0.345219] CPU3: Booted secondary processor [411fd071] [ 0.345308] Brought up 4 CPUs [ 0.345367] SMP: Total of 4 processors activated. [ 0.345383] CPU features: detected feature: 32-bit EL0 Support [ 0.345658] CPU: All CPU(s) started at EL2 [ 0.345687] alternatives: patching kernel code [ 0.354124] devtmpfs: initialized [ 0.392466] Initilizing CustomIPI irq domain [ 0.392813] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.392859] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.404351] pinctrl core: initialized pinctrl subsystem [ 0.405011] OS set in device tree is not L4T. [ 0.405532] regulator-dummy: no parameters [ 0.405835] Initializing plugin-manager [ 0.406009] Plugin module not found [ 0.406213] node /plugin-manager/fragement@0 match with board >=3448-0000-100 [ 0.406728] node /plugin-manager/fragment@1 match with board >=3448-0000-101 [ 0.407724] node /plugin-manager/fragement@7 match with odm-data enable-pmic-wdt [ 0.407945] node /plugin-manager/fragement@8 match with odm-data enable-pmic-wdt [ 0.408605] node /plugin-manager/fragement@13 match with board >=3448-0000-300 [ 0.412272] NET: Registered protocol family 16 [ 0.417918] pstore: using zlib compression [ 0.418426] console [pstore-1] enabled [ 0.418442] pstore: Registered ramoops as persistent store backend [ 0.418460] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.433365] cpuidle: using governor menu [ 0.436897] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.438825] vdso: 2 pages (1 code @ ffffff8008f97000, 1 data @ ffffff8009eb4000) [ 0.438874] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.441936] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.444367] Serial: AMBA PL011 UART driver [ 0.444903] tegra_powergate_init: DONE [ 0.444937] DTS File Name: /home/uni/Nvidia_Jetson/Jetson_Linux_R32_6_1/Source/Linux_for_Tegra/source/public/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.444979] DTB Build time: Dec 4 2021 12:56:32 [ 0.446874] Tegra reboot handler registered. [ 0.451478] iommu: Adding device tegra-carveouts to group 0 [ 0.451696] platform tegra-carveouts: domain=ffffffc0f94583d8 allocates as[0]=ffffffc0f94400a8 [ 0.452078] iommu: Adding device smmu_test to group 1 [ 0.452143] platform smmu_test: domain=ffffffc0f9458618 allocates as[0]=ffffffc0f9440110 [ 0.452993] mc: mapped MMIO address: 0xffffff8008041000 -> 0x70019000 [ 0.453067] mc: mapped MMIO address: 0xffffff8008067000 -> 0x7001c000 [ 0.453137] mc: mapped MMIO address: 0xffffff800807b000 -> 0x7001d000 [ 0.453158] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.453192] mc-err: mcerr ops are set to t21x [ 0.464002] iommu: Adding device 70090000.xusb to group 2 [ 0.464332] iommu: Adding device 70006000.serial to group 3 [ 0.464435] platform 70006000.serial: domain=ffffffc0f94da558 allocates as[0]=ffffffc0f9440178 [ 0.464902] iommu: Adding device 70006040.serial to group 4 [ 0.465198] iommu: Adding device 70006200.serial to group 5 [ 0.465624] iommu: Adding device sound to group 6 [ 0.465691] platform sound: domain=ffffffc0f94daa98 allocates as[0]=ffffffc0f94401e0 [ 0.466278] iommu: Adding device 7000d400.spi to group 7 [ 0.466552] iommu: Adding device 7000d600.spi to group 8 [ 0.466846] iommu: Adding device 70410000.spi to group 9 [ 0.467161] iommu: Adding device 50000000.host1x to group 10 [ 0.467444] iommu: Adding device 54080000.vi to group 11 [ 0.467859] iommu: Adding device 54600000.isp to group 12 [ 0.468166] iommu: Adding device 54680000.isp to group 13 [ 0.468467] iommu: Adding device tegradc.0 to group 14 [ 0.468535] platform tegradc.0: domain=ffffffc0f94e59d8 allocates as[0]=ffffffc0f9440248 [ 0.472743] platform tegradc.0: IOVA linear map 0x0000000092ca9000(800000) [ 0.473156] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.473528] iommu: Adding device tegradc.1 to group 15 [ 0.473597] platform tegradc.1: domain=ffffffc0f94e5c18 allocates as[0]=ffffffc0f94402b0 [ 0.477794] platform tegradc.1: IOVA linear map 0x0000000092ca9000(800000) [ 0.478205] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.478477] iommu: Adding device 54340000.vic to group 16 [ 0.478692] iommu: Adding device 544c0000.nvenc to group 17 [ 0.478906] iommu: Adding device 54500000.tsec to group 18 [ 0.479118] iommu: Adding device 54100000.tsecb to group 19 [ 0.479360] iommu: Adding device 54480000.nvdec to group 20 [ 0.479565] iommu: Adding device 54380000.nvjpg to group 21 [ 0.480607] iommu: Adding device 546c0000.i2c to group 22 [ 0.480950] iommu: Adding device 57000000.gpu to group 23 [ 0.481020] platform 57000000.gpu: domain=ffffffc0f9511c18 allocates as[0]=ffffffc0f9440318 [ 0.481075] platform 57000000.gpu: domain=ffffffc0f9511c18 allocates as[1]=ffffffc0f9440380 [ 0.481134] platform 57000000.gpu: domain=ffffffc0f9511c18 allocates as[2]=ffffffc0f94403e8 [ 0.481213] platform 57000000.gpu: domain=ffffffc0f9511c18 allocates as[3]=ffffffc0f9440450 [ 0.482159] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.482202] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.482227] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET [ 0.482245] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.482260] tegra-pmc: ### PMC reset status reg: 0x3 [ 0.533410] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.533441] tegra-pmc: Clear bootloader IO dpd settings [ 0.533472] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.533554] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.533865] iommu: Adding device 70012000.se to group 24 [ 0.534644] iommu: Adding device 7000c000.i2c to group 25 [ 0.534920] iommu: Adding device 7000c400.i2c to group 26 [ 0.535233] iommu: Adding device 7000c500.i2c to group 27 [ 0.535491] iommu: Adding device 7000c700.i2c to group 28 [ 0.535750] iommu: Adding device 7000d000.i2c to group 29 [ 0.536013] iommu: Adding device 7000d100.i2c to group 30 [ 0.536304] iommu: Adding device sdhci-tegra.2 to group 31 [ 0.536368] platform sdhci-tegra.2: domain=ffffffc0f9585e58 allocates as[0]=ffffffc0f94404b8 [ 0.536845] iommu: Adding device sdhci-tegra.0 to group 32 [ 0.536915] platform sdhci-tegra.0: domain=ffffffc0f9593018 allocates as[0]=ffffffc0f9440520 [ 0.537833] iommu: Adding device 700d0000.xudc to group 33 [ 0.541112] vdd-ac-bat: 5000 mV [ 0.541537] vdd-5v0-sys: 5000 mV [ 0.542215] vdd-5v0-hdmi: 5000 mV [ 0.542652] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.542928] vdd-1v8-sys: 1800 mV [ 0.543372] vdd-fan: 5000 mV [ 0.543592] vdd-fan: supplied by vdd-5v0-sys [ 0.543830] vdd-usb-vbus: 5000 mV [ 0.544055] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.544403] vdd-usb-vbus2: 5000 mV [ 0.578455] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.580720] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.581928] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.581969] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.582003] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.582393] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.590603] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.590987] SCSI subsystem initialized [ 0.591503] usbcore: registered new interface driver usbfs [ 0.591576] usbcore: registered new interface driver hub [ 0.591632] usbcore: registered new device driver usb [ 0.595861] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.598155] random: fast init done [ 0.601480] vdd-core: 600 <--> 1162 mV at 1125 mV [ 0.602511] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.604612] vdd-ddr-1v1: 1150 mV [ 0.608511] vdd-pre-reg-1v35: 1350 mV [ 0.612477] vdd-1v8: 1800 mV [ 0.616489] avdd-sys-1v2: 1200 mV [ 0.620469] vdd-pex-1v0: 1050 mV [ 0.621161] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.621697] max77620-ldo3: at 3100 mV [ 0.624472] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.625016] max77620-ldo5: at 3100 mV [ 0.628471] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 3300 mV [ 0.632476] avdd-1v05-pll: 1050 mV [ 0.636470] avdd-io-hdmi-dp: 1050 mV [ 0.638972] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.639305] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.639620] max77620 4-003c: max77620 probe successful [ 0.642484] media: Linux media interface: v0.10 [ 0.642563] Linux video capture interface: v2.00 [ 0.643560] pps_core: LinuxPPS API ver. 1 registered [ 0.643584] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.643625] PTP clock support registered [ 0.646733] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.647623] Advanced Linux Sound Architecture Driver Initialized. [ 0.648288] Bluetooth: Core ver 2.22 [ 0.648355] NET: Registered protocol family 31 [ 0.648371] Bluetooth: HCI device and connection manager initialized [ 0.648397] Bluetooth: HCI socket layer initialized [ 0.648418] Bluetooth: L2CAP socket layer initialized [ 0.648484] Bluetooth: SCO socket layer initialized [ 0.650362] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.650397] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.650459] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.650486] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.654079] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.655371] vdd-3v3-sys: 3300 mV [ 0.655737] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.655800] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.657458] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.657904] vdd-3v3-sd: 3300 mV [ 0.658322] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.658972] avdd-io-edp-1v05: 1050 mV [ 0.659338] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.659481] vdd-usb-hub-en: 5000 mV [ 0.659827] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.661002] camchar: rtcpu character device driver loaded [ 0.661922] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [ 0.663323] clocksource: Switched to clocksource arch_sys_counter [ 0.705166] VFS: Disk quotas dquot_6.6.0 [ 0.705341] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.705856] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.706362] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.706407] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.706633] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.706657] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.706681] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.706738] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.706762] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.706795] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.706817] nvmap_page_pool_init: Total RAM pages: 1008805 [ 0.706834] nvmap_page_pool_init: nvmap page pool size: 126100 pages (492 MB) [ 0.706935] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.707456] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.708504] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.716851] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.717326] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.717725] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.718010] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.718205] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.718511] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.718529] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.719010] NET: Registered protocol family 2 [ 0.720031] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.720270] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.720828] TCP: Hash tables configured (established 32768 bind 32768) [ 0.721003] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.721098] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.721538] NET: Registered protocol family 1 [ 0.722272] RPC: Registered named UNIX socket transport module. [ 0.722300] RPC: Registered udp transport module. [ 0.722316] RPC: Registered tcp transport module. [ 0.722331] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.722596] Trying to unpack rootfs image as initramfs... [ 1.028652] Freeing initrd memory: 6992K [ 1.038584] host1x 50000000.host1x: initialized [ 1.040582] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.044006] audit: initializing netlink subsys (disabled) [ 1.044131] audit: type=2000 audit(0.883:1): initialized [ 1.044849] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.054730] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.056373] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.057184] 9p: Installing v9fs 9p2000 file system support [ 1.060523] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 1.060680] io scheduler noop registered [ 1.060979] io scheduler cfq registered (default) [ 1.063807] gic 702f9000.agic: GIC IRQ controller registered [ 1.066796] iommu: Adding device 702ef000.adsp to group 34 [ 1.074815] iommu: Adding device aconnect@702c0000:adsp_audio to group 35 [ 1.074973] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 1.075721] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x71e840f [ 1.075753] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 1.077456] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 1.077582] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 1.077698] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 1.077913] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 1.078019] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 1.078130] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 1.078237] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 1.078346] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 1.078459] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 1.078567] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 1.084917] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 1.086632] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 1.088545] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.089820] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 1.090195] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.091507] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 1.091804] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.092071] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 1.092311] Adding domain tsec-pd to PM domain host1x-pd [ 1.095630] tsec 54500000.tsec: initialized [ 1.097053] tsec 54100000.tsecb: initialized [ 1.097816] Adding domain nvdec-pd to PM domain host1x-pd [ 1.101312] nvdec 54480000.nvdec: initialized [ 1.102416] Adding domain vic03-pd to PM domain host1x-pd [ 1.102613] Adding domain msenc-pd to PM domain host1x-pd [ 1.102784] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.106798] falcon 54340000.vic: initialized [ 1.108173] falcon 544c0000.nvenc: initialized [ 1.109551] falcon 54380000.nvjpg: initialized [ 1.114175] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=98 [ 1.114255] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.114307] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.114362] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.114479] display board info: id 0x0, fab 0x0 [ 1.114550] generic_infoframe_type: 0x87 [ 1.114601] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.114621] tegra_cec 70015000.tegra_cec: probed [ 1.114717] tegradc tegradc.0: DT parsed successfully [ 1.114778] tegradc tegradc.0: Display dc.ffffff800abc0000 registered with id=0 [ 1.115359] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 1920x1080 (on 0x0mm) pclk=148350781 [ 1.122661] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.123285] tegradc tegradc.0: probed [ 1.129340] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.130774] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check disabled [ 1.130810] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.131242] kfuse 7000fc00.kfuse: initialized [ 1.133002] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.134095] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.135464] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.135500] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.136072] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.137965] vdd-gpu: applied init 1000000uV constraint [ 1.138020] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.138572] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.142989] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.143222] No Device Node present for smmu client: serial8250 !! [ 1.143255] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.143437] iommu: Adding device serial8250 to group 36 [ 1.147489] console [ttyS0] disabled [ 1.147729] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.578687] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.983208] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.147348] tegra_cec 70015000.tegra_cec: Can't find physical addresse. [ 2.147353] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 2.386794] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.388813] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.495017] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.495029] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.495033] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.495038] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.495043] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.495483] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.507474] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [ 2.507479] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.507489] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit] [ 2.507510] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit] [ 2.507528] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.507538] pci 0000:00:02.0: PCI bridge to [bus 01] [ 2.507544] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.507551] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] [ 2.507971] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 2.507977] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 3.583428] console [ttyS0] enabled [ 3.584034] Console: switching to colour frame buffer device 240x67 [ 3.588669] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 3.589026] serial-tegra 70006200.serial: RX in PIO mode [ 3.589108] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 3.590091] [drm] Initialized [ 3.615121] brd: module loaded [ 3.623713] tegradc tegradc.0: fb registered [ 3.627619] loop: module loaded [ 3.627708] tegra_profiler: version: 1.145, samples/io: 49/28 [ 3.628059] tegra_profiler: auth: init [ 3.632668] THERMAL EST: found 2 subdevs [ 3.632675] THERMAL EST num_resources: 0 [ 3.632680] [THERMAL EST subdev 0] [ 3.632688] [THERMAL EST subdev 1] [ 3.633156] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 3.633159] THERMAL EST: thz register success. [ 3.633319] THERMAL EST: end of probe, return err: 0 [ 3.634431] sd: No Scsi addr parsed to reserve index [ 3.634462] hisi_sas: driver version v1.6 [ 3.640021] tegra-qspi 70410000.spi: Prod settings list not found [ 3.641210] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes) [ 3.641219] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0 [ 3.647541] libphy: Fixed MDIO Bus: probed [ 3.648315] tun: Universal TUN/TAP device driver, 1.6 [ 3.648318] tun: (C) 1999-2004 Max Krasnyansky [ 3.649851] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 3.649856] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.649918] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 3.649920] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.649972] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 3.649975] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.650028] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.4.0-k [ 3.650029] ixgbe: Copyright (c) 1999-2016 Intel Corporation. [ 3.651069] r8168 0000:01:00.0: enabling device (0000 -> 0003) [ 3.651100] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 3.665685] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 3.665839] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:ec:30:b5 from device tree [ 3.666474] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 3.666530] r8168 Copyright (C) 2017 Realtek NIC software team [ 3.666530] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 3.666530] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 3.667181] PPP generic driver version 2.4.2 [ 3.667431] PPP BSD Compression module registered [ 3.667435] PPP Deflate Compression module registered [ 3.667477] PPP MPPE Compression module registered [ 3.667482] NET: Registered protocol family 24 [ 3.667558] usbcore: registered new interface driver r8152 [ 3.667612] usbcore: registered new interface driver asix [ 3.667673] usbcore: registered new interface driver ax88179_178a [ 3.667716] usbcore: registered new interface driver cdc_ether [ 3.667763] usbcore: registered new interface driver net1080 [ 3.667803] usbcore: registered new interface driver cdc_subset [ 3.667857] usbcore: registered new interface driver zaurus [ 3.667914] usbcore: registered new interface driver cdc_ncm [ 3.668094] VFIO - User Level meta-driver version: 0.3 [ 3.669424] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.669446] ehci-pci: EHCI PCI platform driver [ 3.669491] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.669504] ohci-pci: OHCI PCI platform driver [ 3.669546] ohci-platform: OHCI generic platform driver [ 3.672305] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 3.672932] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 3.674119] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f9090c00 id [ 3.677081] tegra-xusb 70090000.xusb: Firmware timestamp: 2020-07-31 09:33:12 UTC, Version: 50.26 release [ 3.677142] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.677172] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 3.677959] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 3.678030] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 3.678235] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.678241] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.678245] usb usb1: Product: xHCI Host Controller [ 3.678250] usb usb1: Manufacturer: Linux 4.9.253-tegra xhci-hcd [ 3.678253] usb usb1: SerialNumber: 70090000.xusb [ 3.678935] hub 1-0:1.0: USB hub found [ 3.678976] hub 1-0:1.0: 5 ports detected [ 3.679680] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.679692] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 3.679820] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.679922] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 3.679928] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.679932] usb usb2: Product: xHCI Host Controller [ 3.679937] usb usb2: Manufacturer: Linux 4.9.253-tegra xhci-hcd [ 3.679941] usb usb2: SerialNumber: 70090000.xusb [ 3.680408] hub 2-0:1.0: USB hub found [ 3.680443] hub 2-0:1.0: 4 ports detected [ 3.681077] usbcore: registered new interface driver uas [ 3.681169] usbcore: registered new interface driver usb-storage [ 3.681289] usbcore: registered new interface driver usbserial [ 3.684833] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 3.684841] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 3.684970] tegra-xudc-new 700d0000.xudc: device count: 1 [ 3.686801] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 3.686816] tegra-xudc-new 700d0000.xudc: vbus state: 0 [ 3.687365] tegra-xudc-new 700d0000.xudc: entering ELPG [ 3.687652] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 3.687827] mousedev: PS/2 mouse device common for all mice [ 3.687936] usbcore: registered new interface driver xpad [ 3.688143] [ILITEK][MSG][ilitek_main_probe:1940] ILITEK client->addr = 0x41 client->irq = 119 [ 3.688149] [ILITEK][MSG][ilitek_main_probe:1953] ilitek log level: 3 [ 3.688152] [ILITEK][MSG][ilitek_power_on:1829] POWER ON [ 3.688196] [ILITEK][MSG][ilitek_get_gpio_num:1574] reset_gpio = 63 irq_gpio = 19 [ 3.688314] [ILITEK][MSG][ilitek_reset:454] delay: 1000 [ 3.783482] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 3.783576] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 2 [ 3.783814] usb usb2: usb_suspend_both: status 0 [ 4.007345] usb 1-2: new full-speed USB device number 2 using tegra-xusb [ 4.033310] usb 1-2: New USB device found, idVendor=045e, idProduct=07b2 [ 4.033316] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.033321] usb 1-2: Product: Microsoft® 2.4GHz Transceiver v8.0 [ 4.033324] usb 1-2: Manufacturer: Microsoft [ 4.155346] usb 1-3: new high-speed USB device number 3 using tegra-xusb [ 4.177107] usb 1-3: New USB device found, idVendor=090c, idProduct=1000 [ 4.177113] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.177116] usb 1-3: Product: USB DISK [ 4.177120] usb 1-3: Manufacturer: SMI Corporation [ 4.177123] usb 1-3: SerialNumber: AA3D54BT77LBRWL6 [ 4.178132] usb-storage 1-3:1.0: USB Mass Storage device detected [ 4.182383] usb-storage 1-3:1.0: Quirks match for vid 090c pid 1000: 400 [ 4.182454] scsi host0: usb-storage 1-3:1.0 [ 4.311645] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [ 4.318949] tegradc tegradc.0: hdmi: tmds rate:148351K prod-setting:prod_c_hdmi_75m_150m [ 4.327546] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [ 4.334700] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [ 4.367879] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 4.374044] Extcon AUX1(HDMI) enable [ 4.378484] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 4.384940] tegradc tegradc.1: No lt-data, using default setting [ 4.419170] tegradc tegradc.0: nominal-pclk:148351648 parent:148350781 div:1.0 pclk:148350781 146868084~161703244 [ 4.429631] tegradc tegradc.1: No hpd-gpio in DT [ 4.434277] tegradc tegradc.1: DT parsed successfully [ 4.439362] tegradc tegradc.1: Display dc.ffffff800d540000 registered with id=1 [ 4.447567] tegradc tegradc.1: dpd enable lookup fail:-19 [ 4.456842] tegradc tegradc.1: probed [ 4.460754] tegradc tegradc.1: fb registered [ 4.472022] V_FRONT_PORCH < (V_REF_TO_SYNC + 1) [ 4.476569] tegradc tegradc.1: Display timing doesn't meet restrictions. [ 4.483278] tegradc tegradc.1: tegra_dc_set_fbcon_boot_mode: set DC mode from modedb, err = -22 [ 4.491981] tegradc tegradc.1: Failed to set fbcon mode for DC 1 [ 4.504107] tegradc tegradc.1: nominal-pclk:25200000 parent:25200000 div:1.0 pclk:25200000 24948000~27468000 [ 4.513985] tegradc tegradc.0: blank - powerdown [ 4.516257] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x0 did not specify bpp [ 4.520062] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 4.524757] dp lt: state 0 (Reset), pending_lt_evt 1 [ 4.524760] dp lt: switching from state 0 (Reset) to state 0 (Reset) [ 4.524764] dp lt: state 0 (Reset), pending_lt_evt 0 [ 4.525966] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 4.526111] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 4.526115] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 4.526562] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 4.526571] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 4.526578] dp lt: tx_pu: 0x20 [ 4.527477] dp lt: CR done [ 4.527481] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 4.527485] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 4.529435] dp lt: CE done [ 4.529439] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 4.529550] hpd: state 7 (Takeover from bootloader), hpd 1, pending_hpd_evt 1 [ 4.529554] hpd: switching from state 7 (Takeover from bootloader) to state 1 (Check Plug) [ 4.555866] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 4.555870] Extcon AUX1(HDMI) disable [ 4.587673] tegradc tegradc.0: unblank [ 4.600303] tegradc tegradc.0: nominal-pclk:138500000 parent:138500000 div:1.0 pclk:138500000 137115000~150965000 [ 4.600377] tegradc tegradc.0: hdmi: tmds rate:138500K prod-setting:prod_c_hdmi_75m_150m [ 4.601422] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 4.631344] hpd: state 1 (Check Plug), hpd 1, pending_hpd_evt 0 [ 4.631351] hpd: switching from state 1 (Check Plug) to state 2 (Check EDID) [ 4.636156] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 4.636159] Extcon AUX1(HDMI) enable [ 4.639335] hpd: state 2 (Check EDID), hpd 1, pending_hpd_evt 0 [ 4.644877] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200080 did not specify bpp [ 4.651803] tegradc tegradc.0: sync windows ret = 246 [ 4.660428] tegradc tegradc.1: nominal-pclk:50390000 parent:25200000 div:1.0 pclk:25200000 49886100~54925100 [ 4.660432] tegradc tegradc.1: pclk out of range! [ 4.708541] [ILITEK][MSG][api_init_func:645] [ 4.716262] tegra-i2c 7000c000.i2c: no acknowledge from address 0x41 [ 4.716292] [ILITEK][ERR][ilitek_i2c_transfer:363] ilitek_i2c_transfer cmd: f0, err: -121 [ 4.744748] tegra-i2c 7000c000.i2c: no acknowledge from address 0x41 [ 4.744776] [ILITEK][ERR][ilitek_i2c_transfer:363] ilitek_i2c_transfer cmd: f0, err: -121 [ 4.774101] tegra-i2c 7000c000.i2c: no acknowledge from address 0x41 [ 4.774129] [ILITEK][ERR][ilitek_i2c_transfer:363] ilitek_i2c_transfer cmd: f0, err: -121 [ 4.796032] tegra-i2c 7000c000.i2c: no acknowledge from address 0x41 [ 4.796059] [ILITEK][ERR][ilitek_i2c_transfer:363] ilitek_i2c_transfer cmd: f0, err: -121 [ 4.816065] [ILITEK][ERR][ilitek_main_probe:1968] init read tp protocol error so exit [ 4.816068] [ILITEK][MSG][ilitek_free_gpio:507] reset_gpio is valid so free [ 4.816085] [ILITEK][MSG][ilitek_free_gpio:511] irq_gpio is valid so free [ 4.816092] [ILITEK][MSG][ilitek_power_on:1829] POWER OFF [ 4.816094] [ILITEK][ERR][ilitek_main_probe:2019] return -ENODEV [ 5.045984] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 5.057421] rtc rtc1: alarm rtc device [ 5.057433] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 5.057460] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 5.057855] i2c /dev entries driver [ 5.059276] i2c i2c-6: Added multiplexed i2c bus 7 [ 5.059631] i2c i2c-6: Added multiplexed i2c bus 8 [ 5.059636] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 5.060202] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [ 5.088088] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 5.088166] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 5.088238] imx219 7-0010: board setup failed [ 5.088289] imx219: probe of 7-0010 failed with error -121 [ 5.088724] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [ 5.119759] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 5.119829] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 5.119895] imx219 8-0010: board setup failed [ 5.119941] imx219: probe of 8-0010 failed with error -121 [ 5.128521] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 5.176128] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 5.176133] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 5.176429] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.176441] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 5.176448] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 5.176569] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.176578] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 5.176584] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 5.176721] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.176729] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 5.176734] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 5.176902] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 5.177459] tegra_aotag tegra-aotag: Registering sensor 0 [ 5.177504] tegra_aotag tegra-aotag: Invalid temp readout [ 5.177524] tegra_aotag tegra-aotag: Invalid temp readout [ 5.177540] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 5.177549] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 5.178329] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.178343] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 5.178491] tegra_aotag tegra-aotag: Invalid temp readout [ 5.178514] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 5.178869] parse_throttle_dt_data: Num cap clks = 6 [ 5.178873] parse_throttle_dt_data: clk=cclk_g type=2 [ 5.178880] parse_throttle_dt_data: clk=gpu type=4 [ 5.178899] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 5.178915] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 5.178933] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 5.178937] parse_throttle_dt_data: clk=emc type=3 [ 5.182545] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.182632] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.182732] tegra_throttle_probe: probe successful. #cdevs=4 [ 5.183347] FAN dev name: pwm-fan [ 5.183392] FAN:gpio request success. [ 5.183435] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 5.183674] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 5.183786] pwm_fan_driver pwm-fan: fan tach request irq success [ 5.183792] pwm_fan_driver pwm-fan: tach period: 1000 [ 5.183866] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 5.183871] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 5.183875] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 5.183879] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 5.183884] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 5.183888] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 5.183892] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 5.183896] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 5.183900] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 5.183904] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 5.209944] device-mapper: uevent: version 1.0.3 [ 5.210327] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 5.212820] tegra210-cpufreq cpufreq: probe()...completed [ 5.213542] sdhci: Secure Digital Host Controller Interface driver [ 5.213543] sdhci: Copyright(c) Pierre Ossman [ 5.213545] sdhci-pltfm: SDHCI platform and OF driver helper [ 5.214371] sdhci-tegra sdhci-tegra.2: Client registration for eMC Successful [ 5.214486] sdhci-tegra sdhci-tegra.2: 3.3V set initially by voltage switch gpio [ 5.214512] sdhci-tegra sdhci-tegra.2: wakeup init done, cdirq 164 [ 5.215143] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 5.215496] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 5.215602] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 301 [ 5.218292] tegra-se 70012000.se: tegra_se_probe: complete [ 5.218829] hidraw: raw HID events driver (C) Jiri Kosina [ 5.228328] sdhci-tegra sdhci-tegra.2: 3.3V set by voltage switch gpio [ 5.237133] input: Microsoft Microsoft® 2.4GHz Transceiver v8.0 as /devices/70090000.xusb/usb1/1-2/1-2:1.0/0003:045E:07B2.0001/input/input0 [ 5.271393] mmc0: SDHCI controller on sdhci-tegra.2 [sdhci-tegra.2] using ADMA 64-bit with 64 bit addr [ 5.272574] mmc1: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 5.303767] hid-generic 0003:045E:07B2.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Microsoft® 2.4GHz Transceiver v8.0] on usb-70090000.xusb-2/input0 [ 5.320143] input: Microsoft Microsoft® 2.4GHz Transceiver v8.0 as /devices/70090000.xusb/usb1/1-2/1-2:1.1/0003:045E:07B2.0002/input/input1 [ 5.320659] hid-generic 0003:045E:07B2.0002: input,hidraw1: USB HID v1.11 Mouse [Microsoft Microsoft® 2.4GHz Transceiver v8.0] on usb-70090000.xusb-2/input1 [ 5.458844] mmc0: host does not support reading read-only switch, assuming write-enable [ 5.478016] mmc0: new SD card at address b368 [ 5.478301] input: Microsoft Microsoft® 2.4GHz Transceiver v8.0 as /devices/70090000.xusb/usb1/1-2/1-2:1.2/0003:045E:07B2.0003/input/input2 [ 5.478502] mmcblk0: mmc0:b368 ST128 121 MiB [ 5.495756] mmcblk0: p1 [ 5.535712] hid-generic 0003:045E:07B2.0003: input,hidraw2: USB HID v1.11 Device [Microsoft Microsoft® 2.4GHz Transceiver v8.0] on usb-70090000.xusb-2/input2 [ 5.535766] usbcore: registered new interface driver usbhid [ 5.535767] usbhid: USB HID core driver [ 5.570296] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 5.570616] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 5.572668] nvpmodel: initialized successfully [ 5.574019] usbcore: registered new interface driver snd-usb-audio [ 5.574078] No Device Node present for smmu client: snd-soc-dummy !! [ 5.574083] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 5.574103] iommu: Adding device snd-soc-dummy to group 37 [ 5.600239] OPE platform probe [ 5.600329] OPE platform probe successful [ 5.600584] OPE platform probe [ 5.600671] OPE platform probe successful [ 5.624315] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 5.624445] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 5.624562] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 5.624685] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 5.624800] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 5.624919] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 5.625037] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 5.625156] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 5.625277] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 5.625395] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 5.637281] u32 classifier [ 5.637283] Actions configured [ 5.637355] Initializing XFRM netlink socket [ 5.638050] NET: Registered protocol family 10 [ 5.638719] NET: Registered protocol family 17 [ 5.638729] NET: Registered protocol family 15 [ 5.638801] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 5.638848] Bluetooth: RFCOMM socket layer initialized [ 5.638856] Bluetooth: RFCOMM ver 1.11 [ 5.638861] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 5.638865] Bluetooth: HIDP socket layer initialized [ 5.638883] 9pnet: Installing 9P2000 support [ 5.638922] Key type dns_resolver registered [ 5.639538] Registered cp15_barrier emulation handler [ 5.639550] Registered setend emulation handler [ 5.640510] registered taskstats version 1 [ 5.641135] Adding domain ve2-pd to PM domain host1x-pd [ 5.641372] Adding domain ve-pd to PM domain host1x-pd [ 5.643449] isp 54600000.isp: initialized [ 5.644378] isp 54680000.isp: initialized [ 5.654710] last reset is due to software reset [ 5.654713] KERNEL: PMC reset status reg: 0x3 [ 5.654779] BL: PMC reset status reg: 0x3 [ 5.654781] BL: PMIC poweroff Event Recorder: 0x0 [ 5.656278] clk_cbus_recalc_rate: no gbus parent [ 5.656283] clk_cbus_round_rate: no gbus parent [ 5.656285] clk_cbus_round_rate: no gbus parent [ 5.656292] clk_cbus_recalc_rate: no gbus parent [ 5.656390] clk_cbus_recalc_rate: no gbus parent [ 5.656392] clk_cbus_round_rate: no gbus parent [ 5.656394] clk_cbus_round_rate: no gbus parent [ 5.656397] clk_cbus_recalc_rate: no gbus parent [ 5.657090] tegra_dvfs: GPU-cap: registered [ 5.657149] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 5.657151] tegra dvfs: vdd-core: nominal 1125mV, offset 600000uV, step 12500uV, scaling enabled [ 5.657153] tegra dvfs: vdd-gpu: nominal 1078mV, offset 708000uV, step 10000uV, scaling enabled [ 5.671364] dp lt: state 5 (link training pass), pending_lt_evt 1 [ 5.671367] dp lt: switching from state 5 (link training pass) to state 0 (Reset) [ 5.671369] dp lt: state 0 (Reset), pending_lt_evt 0 [ 5.671375] dp lt: link training force disable [ 5.671376] dp lt: switching from state 0 (Reset) to state 4 (link training fail/disable) [ 5.742848] tegra_dvfs: vdd-gpu-vts: registered [ 5.779812] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 5.789388] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 5.790513] input: gpio-keys as /devices/gpio-keys/input/input4 [ 5.860342] tegradc tegradc.1: nominal-pclk:50390000 parent:50389160 div:1.0 pclk:50389160 49886100~54925100 [ 5.861948] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200080 did not specify bpp [ 5.865852] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 5.868015] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:00:47 UTC (946688447) [ 5.869043] vi 54080000.vi: vi_probe: ++ [ 6.063378] vi 54080000.vi: initialized [ 6.096898] dp lt: state 4 (link training fail/disable), pending_lt_evt 1 [ 6.096900] dp lt: switching from state 4 (link training fail/disable) to state 0 (Reset) [ 6.096903] dp lt: state 0 (Reset), pending_lt_evt 0 [ 6.097358] vi 54080000.vi: subdev nvcsi--2 bound [ 6.097463] vi 54080000.vi: subdev nvcsi--1 bound [ 6.097677] mmcblk mmc0:b368: Card claimed for testing. [ 6.098220] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 6.098294] Disable partitions left on by BL [ 6.098296] disb [ 6.098338] bwmgr: missing cdev-type property [ 6.098358] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 6.098364] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 6.098429] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 6.098435] DRAM derating cdev registered. [ 6.098971] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 6.098979] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 6.098984] dp lt: tx_pu: 0x20 [ 6.099412] ALSA device list: [ 6.099415] #1: tegra-snd-t210ref-mobile-rt565x [ 6.099882] dp lt: CR done [ 6.099885] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 6.099889] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 6.101795] dp lt: CE done [ 6.101797] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 6.321778] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input3 [ 6.646935] mmc1: hw tuning done ... [ 6.646969] mmc1: new ultra high speed SDR104 SDXC card at address 59b4 [ 6.647528] mmcblk1: mmc1:59b4 59.5 GiB [ 6.739234] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 [ 6.739564] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200080 did not specify bpp [ 6.739569] tegradc tegradc.1: blank - powerdown [ 6.785466] dp lt: state 5 (link training pass), pending_lt_evt 1 [ 6.785469] dp lt: switching from state 5 (link training pass) to state 0 (Reset) [ 6.785471] dp lt: state 0 (Reset), pending_lt_evt 0 [ 6.785475] dp lt: link training force disable [ 6.785476] dp lt: switching from state 0 (Reset) to state 4 (link training fail/disable) [ 6.806375] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200080 did not specify bpp [ 6.806385] tegradc tegradc.1: unblank [ 6.836655] tegradc tegradc.1: nominal-pclk:50390000 parent:50389160 div:1.0 pclk:50389160 49886100~54925100 [ 6.838238] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200080 did not specify bpp [ 6.842142] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 6.847200] dp lt: state 4 (link training fail/disable), pending_lt_evt 1 [ 6.847202] dp lt: switching from state 4 (link training fail/disable) to state 0 (Reset) [ 6.847204] dp lt: state 0 (Reset), pending_lt_evt 0 [ 6.848397] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 6.848541] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 6.848545] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 6.848992] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 6.849001] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 6.849006] dp lt: tx_pu: 0x20 [ 6.849901] dp lt: CR done [ 6.849903] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 6.849907] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 6.851832] dp lt: CE done [ 6.851834] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 6.868605] tegradc tegradc.1: sync windows ret = 246 [ 7.038489] scsi 0:0:0:0: Direct-Access SMI USB DISK 1100 PQ: 0 ANSI: 4 [ 7.039084] sd 0:0:0:0: [sda] 15441920 512-byte logical blocks: (7.91 GB/7.36 GiB) [ 7.039626] sd 0:0:0:0: [sda] Write Protect is off [ 7.040216] sd 0:0:0:0: [sda] No Caching mode page found [ 7.040219] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 7.046181] sda: sda1 [ 7.047858] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 7.157913] extcon-disp-state extcon:disp-state: cable 51 state 1 [ 7.157915] Extcon HDMI: HPD enabled [ 7.157928] tegradc tegradc.0: hdmi: plugged [ 7.178273] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200080 did not specify bpp [ 7.178278] tegradc tegradc.1: blank - powerdown [ 7.182210] Freeing unused kernel memory: 8640K [ 7.218753] dp lt: state 5 (link training pass), pending_lt_evt 1 [ 7.218756] dp lt: switching from state 5 (link training pass) to state 0 (Reset) [ 7.218758] dp lt: state 0 (Reset), pending_lt_evt 0 [ 7.218762] dp lt: link training force disable [ 7.218764] dp lt: switching from state 0 (Reset) to state 4 (link training fail/disable) [ 7.239700] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200080 did not specify bpp [ 7.239711] tegradc tegradc.1: unblank [ 7.269994] tegradc tegradc.1: nominal-pclk:50390000 parent:50389160 div:1.0 pclk:50389160 49886100~54925100 [ 7.271581] tegradc tegradc.1: tegra_dp_get_bpp: vmode=0x200080 did not specify bpp [ 7.275484] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 7.280534] dp lt: state 4 (link training fail/disable), pending_lt_evt 1 [ 7.280537] dp lt: switching from state 4 (link training fail/disable) to state 0 (Reset) [ 7.280539] dp lt: state 0 (Reset), pending_lt_evt 0 [ 7.281730] tegradc tegradc.1: DP: no prod_c_hbr prod settings node in device tree [ 7.281874] dp lt: switching from state 0 (Reset) to state 2 (clock recovery) [ 7.281878] dp lt: state 2 (clock recovery), pending_lt_evt 0 [ 7.282323] dp lt: config: lane 0: vs level: 0, pe level: 0, pc2 level: 0 [ 7.282332] dp lt: config: lane 1: vs level: 0, pe level: 0, pc2 level: 0 [ 7.282337] dp lt: tx_pu: 0x20 [ 7.283231] dp lt: CR done [ 7.283234] dp lt: switching from state 2 (clock recovery) to state 3 (channel equalization) [ 7.283238] dp lt: state 3 (channel equalization), pending_lt_evt 0 [ 7.285156] dp lt: CE done [ 7.285159] dp lt: switching from state 3 (channel equalization) to state 5 (link training pass) [ 7.301929] tegradc tegradc.1: sync windows ret = 246 [ 7.535925] extcon-disp-state extcon:disp-state: cable 44 state 1 [ 7.544240] Extcon DP: HPD enabled [ 7.549766] hpd: Display connected, hpd_switch 1 [ 7.556554] hpd: switching from state 2 (Check EDID) to state 4 (Enabled) [ 7.558386] Root device found: mmcblk0p1 [ 7.559856] Found dev node: /dev/mmcblk0p1 [ 7.754817] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 7.768846] Rootfs mounted over mmcblk0p1 [ 7.794731] Switching from initrd to actual rootfs [ 7.807988] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00 [ 7.807988] [ 7.821171] CPU: 0 PID: 1 Comm: chroot Not tainted 4.9.253-tegra #6 [ 7.829456] Hardware name: NVIDIA Jetson Nano Developer Kit (DT) [ 7.837468] Call trace: [ 7.841921] [] dump_backtrace+0x0/0x198 [ 7.849329] [] show_stack+0x24/0x30 [ 7.856406] [] dump_stack+0xa0/0xc4 [ 7.863461] [] panic+0x12c/0x2a8 [ 7.870263] [] complete_and_exit+0x0/0x30 [ 7.877837] [] do_group_exit+0x40/0xa8 [ 7.885130] [] __wake_up_parent+0x0/0x40 [ 7.892587] [] el0_svc_naked+0x34/0x38 [ 7.899850] SMP: stopping secondary CPUs [ 7.905752] Kernel Offset: disabled [ 7.911139] Memory Limit: none [ 7.922538] Rebooting in 5 seconds..