[0000.203] [TegraBoot] (version 00.00.2018.01-l4t-a2563f57) [0000.208] Processing in cold boot mode Bootloader 2 [0000.213] A02 Bootrom Patch rev = 1023 [0000.216] Power-up reason: software reset [0000.220] No Battery Present [0000.223] pmic max77620 reset reason [0000.226] pmic max77620 NVERC : 0x0 [0000.229] RamCode = 0 [0000.232] Platform has DDR4 type RAM [0000.235] max77620 disabling SD1 Remote Sense [0000.239] Setting DDR voltage to 1125mv [0000.243] Serial Number of Pmic Max77663: 0xd15ee [0000.251] Entering ramdump check [0000.254] Get RamDumpCarveOut = 0x0 [0000.257] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.262] Last reboot was clean, booting normally! [0000.267] Sdram initialization is successful [0000.271] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.277] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.283] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.289] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.294] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.300] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.306] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.312] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.328] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.334] Platform-DebugCarveout: 0 [0000.337] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.343] Non secure mode, and RB not enabled. [0000.360] Csd NumOfBlocks=0 [0004.312] *** Booting BFS0. [0004.319] Using BFS PT to query partitions [0010.209] *** Booting KFS0. [0010.213] Using GPT Primary to query partitions [0010.218] Error in NvTbootLoadBinary: 0x1 ! [0010.222] failed to load NvTbootTbootCpu from (0:3) [0010.226] re-load NvTbootTbootCpu from (4:0) [0010.231] Using GPT Primary to query partitions [0010.240] Using BFS PT to query partitions [0010.244] Error in NvTbootLoadBinary: 0x1 ! [0010.249] Error in NvTbootLoadBinary: 0x1 ! [0010.253] Error is 1 [0009.812] Enabled early print [0009.815] [TegraBoot] (version 00.00.2018.01-l4t-32ed9048) [0009.820] Processing in recovery mode [0009.823] A02 Bootrom Patch rev = 1023 [0009.827] Power-up reason: pmc por [0009.830] Established communication link with host [0011.044] Odmdata from BCT: 0x00094000 [0011.048] DebugPort= 0x3 [0011.100] EEPROM CRC failed. Calculated crc=0xe3 CRC stored = 0xb6 [0011.106] WARNING: Verifying Eeprom failed [0011.110] BoardId read from EEPROM/NCT: 3448 [0011.114] BoardID = 3448, SKU = 0x2 [0011.141] No Battery Present [0011.144] RamCode = 0 [0011.146] Platform has DDR4 type RAM [0011.150] max77620 disabling SD1 Remote Sense [0011.154] Setting DDR voltage to 1125mv [0011.158] Serial Number of Pmic Max77663: 0xd15ee [0011.165] Entering ramdump check [0011.168] Get RamDumpCarveOut = 0x0 [0011.172] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0011.177] Last reboot was clean, booting normally! [0011.181] Sdram initialization is successful [0011.186] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0011.192] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0011.197] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0011.203] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0011.209] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0011.215] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0011.221] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0011.227] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0011.243] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0011.249] Platform-DebugCarveout: 0 [0011.252] Downloaded BCT successfully [0011.379] Downloaded Bootloader successfully [0011.429] Downloaded rp1 successfully [0011.451] MAX77620_GPIO5 configured [0011.455] CPU power rail is up [0011.458] CPU clock enabled [0011.461] Performing RAM repair [0011.464] Updating A64 Warmreset Address to 0x92c002e9 [0011.471] Enable APE clock/reset [0011.474] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0011.478] Loading Secure OS image failed. [0011.482] Set NvDecSticky Bits [0011.486] GSC2 address ff53fffc value c0edbbcc [0011.492] GSC MC Settings done [0011.496] Next binary entry address: 0x92c00258 [0011.501] BoardId: 3448 [0011.503] Overriding pmu board id with proc board id [0011.508] Display board id is not available [0011.512] Starting CPU & Halting co-processor [0011.800] [0011.801] Debug Init done [0011.804] Marked DTB cacheable [0011.807] Bootloader DTB loaded at 0x83000400 [0011.812] DeviceTree Init done [0011.825] Pinmux applied successfully [0011.829] gicd_base: 0x50041000 [0011.832] gicc_base: 0x50042000 [0011.835] Interrupts Init done [0011.839] Using base:0x60005090 & irq:208 for tick-timer [0011.845] Using base:0x60005098 for delay-timer [0011.849] platform_init_timer: DONE [0011.853] Timer(tick) Init done [0011.856] osc freq = 38400 khz [0011.860] [0011.862] Welcome to L4T Cboot [0011.864] [0011.866] Cboot Version: 00.00.2018.01-t210-40c3ff9c [0011.871] calling constructors [0011.874] initializing heap [0011.876] initializing threads [0011.879] initializing timers [0011.882] creating bootstrap completion thread [0011.886] top of bootstrap2() [0011.889] CPU: ARM Cortex A57 [0011.892] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0011.897] initializing platform [0012.047] Config for emmc ddr50 mode completed [0012.051] sdmmc bdev is already initialized [0012.055] of_register: registering tegra_udc to of_hal [0012.061] of_register: registering inv20628-driver to of_hal [0012.066] of_register: registering ads1015-driver to of_hal [0012.072] of_register: registering lp8557-bl-driver to of_hal [0012.078] of_register: registering bq2419x_charger to of_hal [0012.083] of_register: registering bq27441_fuel_gauge to of_hal [0012.095] gpio framework initialized [0012.098] of_register: registering tca9539_gpio to of_hal [0012.104] of_register: registering tca9539_gpio to of_hal [0012.109] of_register: registering i2c_bus_driver to of_hal [0012.114] of_register: registering i2c_bus_driver to of_hal [0012.120] of_register: registering i2c_bus_driver to of_hal [0012.126] pmic framework initialized [0012.129] of_register: registering max77620_pmic to of_hal [0012.135] regulator framework initialized [0012.138] of_register: registering tps65132_bl_driver to of_hal [0012.144] initializing target [0012.150] gpio_driver_register: register 'tegra_gpio_driver' driver [0012.161] fixed regulator driver initialized [0012.178] initializing OF layer [0012.182] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.199] I2C Bus Init done [0012.202] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.212] I2C Bus Init done [0012.215] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.225] I2C Bus Init done [0012.228] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.238] I2C Bus Init done [0012.241] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.251] I2C Bus Init done [0012.254] of_children_init: Ops found for compatible string maxim,max77620 [0012.264] max77620_init using irq 118 [0012.269] register 'maxim,max77620' pmic [0012.273] gpio_driver_register: register 'max77620-gpio' driver [0012.280] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.290] I2C Bus Init done [0012.294] Applying platform configs [0012.301] platform-init is not present. Skipping [0012.305] calling apps_init() [0012.322] Found 17 GPT partitions in "sdmmc3_user" [0012.326] Proceeding to flashing Server [0012.330] usbdcd_reinit Initialize driver to use already enumerated device [0012.337] nv3p_priv_usbf_open USB configuration success [0012.344] Writing LNX partition [0012.396] partition LNX write successful. [0012.411] Writing BCT partition [0012.803] partition BCT write successful. [0012.818] Change state to cold boot mode [0000.203] [TegraBoot] (version 00.00.2018.01-l4t-a2563f57) [0000.208] Processing in cold boot mode Bootloader 2 [0000.213] A02 Bootrom Patch rev = 1023 [0000.216] Power-up reason: software reset [0000.220] No Battery Present [0000.223] pmic max77620 reset reason [0000.226] pmic max77620 NVERC : 0x0 [0000.229] RamCode = 0 [0000.232] Platform has DDR4 type RAM [0000.235] max77620 disabling SD1 Remote Sense [0000.239] Setting DDR voltage to 1125mv [0000.243] Serial Number of Pmic Max77663: 0xd15ee [0000.251] Entering ramdump check [0000.254] Get RamDumpCarveOut = 0x0 [0000.257] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.262] Last reboot was clean, booting normally! [0000.267] Sdram initialization is successful [0000.271] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.277] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.283] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.289] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.295] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.300] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.306] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.312] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.328] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.334] Platform-DebugCarveout: 0 [0000.338] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.343] Non secure mode, and RB not enabled. [0000.360] Csd NumOfBlocks=0 [0000.370] Using BFS PT to query partitions [0000.378] Using GPT Primary to query partitions [0000.383] Error in NvTbootLoadBinary: 0x1 ! [0000.387] failed to load NvTbootTbootCpu from (0:3) [0000.391] re-load NvTbootTbootCpu from (4:0) [0000.400] Using GPT Primary to query partitions [0000.407] Using BFS PT to query partitions [0000.412] Error in NvTbootLoadBinary: 0x1 ! [0000.416] Error in NvTbootLoadBinary: 0x1 ! [0000.420] Error is 1