▒▒ [0044.595] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0044.603] I> MB1 (prd-version: 1.5.1.9-t194-41334769-73a9b7ef) [0044.609] I> Boot-mode: Platform RCM [0044.612] I> Chip revision : A02P [0044.615] I> Bootrom patch version : 15 (correctly patched) [0044.620] I> ATE fuse revision : 0x200 [0044.624] I> Ram repair fuse : 0x0 [0044.627] I> Ram Code : 0x2 [0044.629] I> rst_source : 0x0 [0044.632] I> rst_level : 0x0 [0044.636] I> USB configuration success [0046.872] I> mb2 image downloaded [0046.972] I> Recovery boot mode 0 [0046.977] I> Boot-device: eMMC [0046.982] I> UPHY full init done [0046.989] I> MB1 done [0046.994] W> Profiler not initialized [0046.997] I> Welcome to MB2(TBoot-BPMP) Applet (version: 00.00.2018.32-mobile-ca3b3e95) [0047.005] W> Profiler not initialized [0047.009] I> DMA Heap @ [0x40020000 - 0x40065800] [0047.013] I> Default Heap @ [0xd486400 - 0xd48a400] [0047.018] W> Profiler not initialized [0047.021] W> Profiler not initialized [0047.025] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0047.030] W> device prod register failed [0047.034] W> Profiler not initialized [0047.398] I> sdmmc DDR50 mode [0047.402] I> No supported QSPI flash found [0047.406] E> QSPI Flash: Insufficient flash size (0 MB) [0047.411] I> QSPI Flash is not present. [0047.462] E> Link startup dme_set failed [0047.466] E> UFS initialization failed [0047.470] I> UFS is not present [0047.473] W> Profiler not initialized [0047.480] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0047.490] I> Found 42 partitions in SDMMC_USER (instance 3) [0047.495] W> Profiler not initialized [0047.499] W> Profiler not initialized [0047.502] W> Profiler not initialized [0047.506] I> Entering 3p server [0047.509] I> USB configuration success [0048.349] I> Populate chip info [0048.457] I> Populate eeprom info [0048.464] I> Populate eeprom info for module cvm [0048.675] I> Rebooting : reboot-recovery [004▒▒ [0206.290] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0206.298] I> MB1 (prd-version: 1.5.1.9-t194-41334769-73a9b7ef) [0206.304] I> Boot-mode: RCM [0206.307] I> Chip revision : A02P [0206.310] I> Bootrom patch version : 15 (correctly patched) [0206.315] I> ATE fuse revision : 0x200 [0206.318] I> Ram repair fuse : 0x0 [0206.321] I> Ram Code : 0x2 [0206.324] I> rst_source : 0xb [0206.327] I> rst_level : 0x1 [0206.330] I> USB configuration success [0208.469] I> bct_bootrom image downloaded [0208.484] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0208.492] I> Temperature = 44000 [0208.495] W> Skipping boost for clk: BPMP_CPU_NIC [0208.500] W> Skipping boost for clk: BPMP_APB [0208.504] W> Skipping boost for clk: AXI_CBB [0208.508] W> Skipping boost for clk: AON_CPU_NIC [0208.512] W> Skipping boost for clk: CAN1 [0208.516] W> Skipping boost for clk: CAN2 [0208.520] I> Boot-device: eMMC [0208.523] I> Boot-device: eMMC [0208.526] I> bct_mb1 image downloaded [0208.545] I> ECC region[0]: Start:0x0, End:0x0 [0208.550] I> ECC region[1]: Start:0x0, End:0x0 [0208.554] I> ECC region[2]: Start:0x0, End:0x0 [0208.558] I> ECC region[3]: Start:0x0, End:0x0 [0208.562] I> ECC region[4]: Start:0x0, End:0x0 [0208.566] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0208.572] I> Non-ECC region[1]: Start:0x0, End:0x0 [0208.576] I> Non-ECC region[2]: Start:0x0, End:0x0 [0208.581] I> Non-ECC region[3]: Start:0x0, End:0x0 [0208.585] I> Non-ECC region[4]: Start:0x0, End:0x0 [0208.591] E> FAILED: Thermal config [0208.599] E> FAILED: MEMIO rail config [0208.617] I> bct_mem image downloaded [0210.216] I> blob image downloaded [0210.313] I> Recovery boot mode 0 ▒▒ [0000.055] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0000.064] I> MB1 (prd-version: 1.5.1.9-t194-41334769-73a9b7ef) [0000.069] I> Boot-mode: Coldboot [0000.072] I> Chip revision : A02P [0000.075] I> Bootrom patch version : 15 (correctly patched) [0000.080] I> ATE fuse revision : 0x200 [0000.084] I> Ram repair fuse : 0x0 [0000.087] I> Ram Code : 0x2 [0000.090] I> rst_source : 0xa [0000.092] I> rst_level : 0x1 [0000.096] I> Boot-device: eMMC [0000.111] I> sdmmc DDR50 mode [0000.115] W> No valid slot number is found in scratch register [0000.120] W> Return default slot: _a [0000.124] I> Active Boot chain : 0 [0000.127] I> Boot-device: eMMC [0000.130] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.137] I> Temperature = 44000 [0000.140] W> Skipping boost for clk: BPMP_CPU_NIC [0000.144] W> Skipping boost for clk: BPMP_APB [0000.148] W> Skipping boost for clk: AXI_CBB [0000.152] W> Skipping boost for clk: AON_CPU_NIC [0000.156] W> Skipping boost for clk: CAN1 [0000.160] W> Skipping boost for clk: CAN2 [0000.164] I> Boot-device: eMMC [0000.167] I> Boot-device: eMMC [0000.176] I> Sdmmc: HS400 mode enabled [0000.181] I> ECC region[0]: Start:0x0, End:0x0 [0000.185] I> ECC region[1]: Start:0x0, End:0x0 [0000.189] I> ECC region[2]: Start:0x0, End:0x0 [0000.193] I> ECC region[3]: Start:0x0, End:0x0 [0000.197] I> ECC region[4]: Start:0x0, End:0x0 [0000.202] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.207] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.212] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.216] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.221] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.226] E> FAILED: Thermal config [0000.233] E> FAILED: MEMIO rail config [0000.252] I> Boot-device: eMMC [0000.261] I> sdmmc bdev is already initialized [0000.336] I> MB1 done ▒▒▒▒main enter SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init ▒▒ [0000.344] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-6fc80c72) [0000.345] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0000.346] I> Default Heap @ [0xd486400 - 0xd48a400] [0000.346] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0000.352] W> device prod register failed [0000.356] I> gpio framework initialized [0000.360] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver [0000.367] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver [0000.375] I> No valid sdcard_params in mb1_bct [0000.379] I> Boot-device: eMMC [0000.382] I> Boot_device: SDMMC_BOOT instance: 3 [0000.391] I> sdmmc-3 params source = boot args [0000.392] I> sdmmc bdev is already initialized [0000.395] I> sdmmc-3 params source = boot args [0000.429] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0000.445] I> Found 42 partitions in SDMMC_USER (instance 3) [0000.446] W> No valid slot number is found in scratch register [0000.446] W> Return default slot: _a [0000.447] I> Active Boot chain : 0 [0000.453] I> parsing oem signed section of bpmp-fw header done [0000.460] I> bpmp-fw binary init read from storage [0000.461] I> oem authentication of bpmp-fw header done [0000.463] I> bpmp-fw binary done read from storage [0000.464] I> bpmp-fw: Authentication init Done [0000.471] I> parsing oem signed section of cpubl header done [0000.477] I> cpubl binary init read from storage [0000.478] I> bpmp-fw: Authentication Finalize Done [0000.478] I> oem authentication of cpubl header done [0000.481] I> cpubl binary done read from storage [0000.486] I> cpubl: Authentication init Done [0000.496] I> parsing oem signed section of rce header done [0000.503] I> rce binary init read from storage [0000.503] I> Relocating BR-BCT [0000.504] I> cpubl: Authentication Finalize Done [0000.507] I> oem authentication of rce header done [0000.511] I> rce binary done read from storage [0000.516] I> rce: Authentication init Done [0000.526] I> parsing oem signed section of ape header done [0000.532] I> ape binary init read from storage [0000.533] I> rce: Authentication Finalize Done [0000.534] I> oem authentication of ape header done [0000.538] I> ape binary done read from storage [0000.542] I> ape: Authentication init Done [0000.553] I> parsing oem signed section of tos header done [0000.559] I> tos binary init read from storage [0000.560] I> ape: Authentication Finalize Done [0000.561] I> oem authentication of tos header done [0000.565] I> tos binary done read from storage [0000.569] I> tos: Authentication init Done [0000.579] I> parsing oem signed section of bpmp-fw-dtb header done [0000.586] I> bpmp-fw-dtb binary init read from storage [0000.587] I> tos: Authentication Finalize Done [0000.590] I> oem authentication of bpmp-fw-dtb header done [0000.597] I> bpmp-fw-dtb binary done read from storage [0000.599] I> bpmp-fw-dtb: Authentication init Done [0000.610] I> parsing oem signed section of cpubl-dtb header done [0000.616] I> cpubl-dtb binary init read from storage [0000.617] I> bpmp-fw-dtb: Authentication Finalize Done [0000.651] I> oem authentication of cpubl-dtb header done [0000.652] I> cpubl-dtb binary done read from storage [0000.653] I> cpubl-dtb: Authentication init Done [0000.659] I> parsing oem signed section of eks header done [0000.666] I> eks binary init read from storage [0000.667] I> cpubl-dtb: Authentication Finalize Done [0000.667] I> oem authentication of eks header done [0000.668] I> eks binary done read from storage [0000.668] I> eks: Authentication init Done [0000.669] I> eks: Authentication Finalize Done [0000.672] I> EKB detected (length: 0x410) @ VA:0x52700400 ▒▒NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 08:55:29, Feb 19 2022 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 41: hwkey-agent is running!! hwkey-agent: 347: key_mgnt_processing ....... hwkey-agent: 255: Setting EKB key 0 to slot 14 hwkey-agent: 178: Init hweky-agent services!! luks-srv: 40: luks-srv is running!! luks-srv: 157: Init luks-srv IPC services!! platform_bootstrap_epilog: trusty bootstrap complete ▒▒ welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is e73a758761f0c6d24a1e69a2ac6b5035 tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized 392 clocks registered WARNING: pll_c4 has no dyn ramp clk_mrq_init: mrq handler registered clk initialized nvlink initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized uphy_mrq_init: mrq handler registered uphy_dt initialized uphy initialized safereg_init: period 80 ms ec_late initialized mrq initialized ▒▒ [0001.174] I> Welcome to Cboot ▒▒fmon_post initialized ▒▒[0001.174] I> Cboot Version: t194-63226c45 [0001.174] I> CPU-BL Params @ 0xf2820000 [0001.175] I> 0) Base:0x00000000 Size:0x00000000 [0001.178] I> 1) Base:0xf1100000 Size:0x00100000 [0001.183] I> 2) Base:0xf2000000 Size:0x00200000 [0001.187] I> 3) Base:0xf1200000 Size:0x00200000 ▒▒clk_set_parent failed for clk i2c2, parent pll_aon (-22) clk_set_parent failed for clk i2c8, parent pll_aon (-22) clk_dt_late initialized machine_check initialized pm_post initialized dbells initialized avfs_clk_platform_post initialized dmce initialized cvc initialized ccplex_avfs_hw_init: nafll_cluster0: not monitored ccplex_avfs_hw_init: nafll_cluster1: not monitored ccplex_avfs_hw_init: nafll_cluster2: not monitored ccplex_avfs_hw_init: nafll_cluster3: not monitored avfs_clk_mach_post initialized regulator_post initialized rm initialized sc7_diag initialized thermal_test initialized serial_late initialized clk_post initialized clk_dt_post initialized mc_reg initialized pg_post initialized dyn_modules initialized sku_debugfs initialized speedo_debugfs initialized adc_debugfs initialized clk_debugfs initialized ▒▒[0001.192] I> 4) Base:0xf1000000 Size:0x00100000 [0001.271] I> 5) Base:0xf0f00000 Size:0x00100000 [0001.275] I> 6) Base:0xf3800000 Size:0x00400000 [0001.280] I> 7) Base:0xf1c00000 Size:0x00400000 [0001.284] I> 8) Base:0xf0e00000 Size:0x00100000 [0001.289] I> 9) Base:0xf0d00000 Size:0x00100000 [0001.293] I> 10) Base:0xf3000000 Size:0x00800000 [0001.298] I> 11) Base:0x40000000 Size:0x00040000 [0001.302] I> 12) Base:0xf0c00000 Size:0x00100000 [0001.307] I> 13) Base:0x40046000 Size:0x00002000 [0001.311] I> 14) Base:0x40048000 Size:0x00002000 [0001.316] I> 15) Base:0xac000000 Size:0x00004000 ▒▒emc_debugfs initialized dvs_debugfs initialized fmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized debugfs_cons initialized mail_fs initialized profile initialized cvc_debugfs initialized dmce_debugfs initialized ec_debugfs initialized rm_debugfs initialized soctherm_debug initialized gr_reader initialized mods initialized dt_fs initialized debugfs_mrq initialized debug_mrq initialized debug_safereg initialized initializing target calling apps_init() starting app shell entering main console loop ] ▒▒[0001.320] I> 16) Base:0x4004a000 Size:0x00002000 [0001.375] I> 17) Base:0xf0b00000 Size:0x00100000 [0001.379] I> 18) Base:0x4004c000 Size:0x00002000 [0001.384] I> 19) Base:0xf2200000 Size:0x00600000 [0001.388] I> 20) Base:0x4004e000 Size:0x00002000 [0001.393] I> 21) Base:0xf0ad0000 Size:0x0000c000 [0001.397] I> 22) Base:0x00000000 Size:0x00000000 [0001.402] I> 23) Base:0xf0ae0000 Size:0x00020000 [0001.406] I> 24) Base:0xf6000000 Size:0x02000000 [0001.411] I> 25) Base:0x40050000 Size:0x00002000 [0001.415] I> 26) Base:0x40040000 Size:0x00006000 [0001.420] I> 27) Base:0xf1800000 Size:0x00400000 [0001.424] I> 28) Base:0xf4c00000 Size:0x01400000 [0001.429] I> 29) Base:0xf1400000 Size:0x00400000 [0001.433] I> 30) Base:0x00000000 Size:0x00000000 [0001.437] I> 31) Base:0x00000000 Size:0x00000000 [0001.442] I> 32) Base:0xf8000000 Size:0x08000000 [0001.446] I> 33) Base:0x00000000 Size:0x00000000 [0001.451] I> 34) Base:0xf3c00000 Size:0x01000000 [0001.455] I> 35) Base:0xab000000 Size:0x01000000 [0001.460] I> 36) Base:0xa0000000 Size:0x0b000000 [0001.464] I> 37) Base:0xf2800000 Size:0x00800000 [0001.469] I> 38) Base:0x80000000 Size:0x20000000 [0001.473] I> 39) Base:0xb0000000 Size:0x08000000 [0001.478] I> 40) Base:0x00000000 Size:0x00000000 [0001.482] I> 41) Base:0x00000000 Size:0x00000000 [0001.487] I> 42) Base:0x00000000 Size:0x00000000 [0001.491] I> 43) Base:0x00000000 Size:0x00000000 [0001.495] I> 44) Base:0x00000000 Size:0x00000000 [0001.500] I> 45) Base:0x00000000 Size:0x00000000 [0001.504] GIC-SPI Target CPU: 0 [0001.507] Interrupts Init done [0001.510] calling constructors [0001.513] initializing heap [0001.516] I> Heap: [0xa0699b80 ... 0xab000000] [0001.520] initializing threads [0001.523] initializing timers [0001.526] creating bootstrap completion thread [0001.530] top of bootstrap2() [0001.533] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000 [0001.537] initializing platform [0001.540] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0001.546] W> device prod register failed [0001.550] I> Bl_dtb @0xaaf00000 [0001.556] W> "plugin-manager" doesn't exist, creating [0001.558] W> "ids" doesn't exist, creating [0001.562] W> "connection" doesn't exist, creating [0001.566] W> "configs" doesn't exist, creating [0001.578] E> failed to read label property for node 227404: 13 [0001.581] E> failed to read reg property for node 227492: 13 [0001.584] E> failed to read label property for node 227544: 13 [0001.588] E> failed to read label property for node 227612: 13 [0001.594] E> failed to read label property for node 227648: 13 [0001.600] E> failed to read label property for node 227684: 13 [0001.605] E> failed to read reg property for node 227752: 13 [0001.611] E> failed to read label property for node 227804: 13 [0001.617] I> Find /i2c@3160000's alias i2c0 [0001.619] I> Reading eeprom i2c=0 address=0x50 [0001.649] I> Device at /i2c@3160000:0x50 [0001.649] I> Reading eeprom i2c=0 address=0x56 [0001.674] I> Device at /i2c@3160000:0x56 [0001.675] I> Find /i2c@3180000's alias i2c2 [0001.675] I> Reading eeprom i2c=2 address=0x54 [0001.677] E> I2C: slave not found in slaves. [0001.677] E> I2C: Could not write 0 bytes to slave: 0x00a8 with repeat start true. [0001.678] E> I2C_DEV: Failed to send register address 0x00000000. [0001.678] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa8 at 0x00000000 via instance 2. [0001.688] E> eeprom: Failed to read I2C slave device [0001.693] I> Eeprom read failed 0x3526070d [0001.697] I> Reading eeprom i2c=2 address=0x57 [0001.701] E> I2C: slave not found in slaves. [0001.705] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0001.713] E> I2C_DEV: Failed to send register address 0x00000000. [0001.718] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 2. [0001.728] E> eeprom: Failed to read I2C slave device [0001.733] I> Eeprom read failed 0x3526070d [0001.737] I> Reading eeprom i2c=2 address=0x52 [0001.741] E> I2C: slave not found in slaves. [0001.745] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.753] E> I2C_DEV: Failed to send register address 0x00000000. [0001.758] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 2. [0001.768] E> eeprom: Failed to read I2C slave device [0001.773] I> Eeprom read failed 0x3526070d [0001.777] I> Find /i2c@c240000's alias i2c1 [0001.781] I> Reading eeprom i2c=1 address=0x52 [0001.786] E> I2C: slave not found in slaves. [0001.789] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.797] E> I2C_DEV: Failed to send register address 0x00000000. [0001.802] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.812] E> eeprom: Retry to read I2C slave device. [0001.817] E> I2C: slave not found in slaves. [0001.821] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.829] E> I2C_DEV: Failed to send register address 0x00000000. [0001.834] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.844] E> eeprom: Failed to read I2C slave device [0001.849] I> Eeprom read failed 0x3526070d [0001.853] I> Reading eeprom i2c=1 address=0x50 [0001.857] E> I2C: slave not found in slaves. [0001.861] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.869] E> I2C_DEV: Failed to send register address 0x00000000. [0001.874] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.884] E> eeprom: Retry to read I2C slave device. [0001.889] E> I2C: slave not found in slaves. [0001.893] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.901] E> I2C_DEV: Failed to send register address 0x00000000. [0001.906] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.916] E> eeprom: Failed to read I2C slave device [0001.921] I> Eeprom read failed 0x3526070d [0001.925] I> create_pm_ids: id: 2888-0004-400-P, len: 15 [0001.930] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.941] I> create_pm_ids: id: 2822-0000-700-L, len: 15 [0001.946] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.957] I> Adding plugin-manager/ids/2888-0004-400=/i2c@3160000:module@0x50 [0001.964] W> "i2c@3160000" doesn't exist, creating [0001.969] W> "module@0x50" doesn't exist, creating [0001.973] I> Adding plugin-manager/ids/2822-0000-700=/i2c@3160000:module@0x56 [0001.980] W> "module@0x56" doesn't exist, creating [0001.986] I> Adding plugin-manager/cvm [0001.989] W> "chip-id" doesn't exist, creating [0001.993] I> Adding plugin-manager/chip-id/A02P [0001.997] I> Plugin-manager override starting [0002.002] I> node /plugin-manager/fragement-tegra-wdt-en matches [0002.010] I> node /plugin-manager/fragement-soft-wdt matches [0002.017] I> node /plugin-manager/fragment-pcie-c5-rp matches [0002.021] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0002.034] I> Disable plugin-manager status in FDT [0002.034] I> Plugin-manager override finished successfully [0002.035] I> gpio framework initialized [0002.039] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver [0002.046] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver [0002.053] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 [0002.060] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.068] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.075] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.081] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 [0002.088] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.096] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.103] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.110] I> fixed regulator driver initialized [0002.122] I> register 'maxim' power off handle [0002.123] I> virtual i2c enabled [0002.123] I> registered 'maxim,max20024' pmic [0002.125] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver [0002.131] I> Boot-device: eMMC [0002.134] I> Boot_device: SDMMC_BOOT instance: 3 [0002.143] I> sdmmc-3 params source = boot args [0002.143] I> create_pm_ids: id: 2888-0004-400-P, len: 15 [0002.148] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.159] I> create_pm_ids: id: 2822-0000-700-L, len: 15 [0002.164] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.175] I> sdmmc bdev is already initialized [0002.180] I> sdmmc-3 params source = boot args [0002.210] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0002.223] I> Found 42 partitions in SDMMC_USER (instance 3) [0002.232] I> enabling 'vdd-hdmi-5v0' regulator [0002.237] I> regulator 'vdd-hdmi-5v0' already enabled [0002.237] I> hdmi cable connected [0002.239] W> set volts not configured for 'vdd-1v0' [0002.242] W> set volts not configured for 'vdd-1v8-hs' [0002.242] I> retrieved tmds range from prod_list_hdmi_soc [0002.246] E> invalid display type [0002.250] E> invalid display type [0002.251] E> cannot find any other nvdisp nodes [0002.266] I> edid read success [0002.279] I> edid read success [0002.279] I> width = 640, height = 480, frequency = 25174825 [0002.279] I> width = 640, height = 480, frequency = 25174825 [0002.280] I> width = 640, height = 480, frequency = 25174825 [0002.280] I> width = 1920, height = 1080, frequency = 148500000 [0002.281] I> width = 1920, height = 1080, frequency = 148500000 [0002.285] I> width = 1920, height = 1080, frequency = 148351648 [0002.290] I> width = 1280, height = 720, frequency = 74175824 [0002.296] I> width = 720, height = 480, frequency = 26973026 [0002.302] I> width = 720, height = 480, frequency = 26973026 [0002.307] I> width = 1920, height = 1080, frequency = 148351648 [0002.313] I> width = 1280, height = 720, frequency = 74175824 [0002.318] I> width = 720, height = 576, frequency = 26973026 [0002.324] I> width = 720, height = 576, frequency = 26973026 [0002.329] I> Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.339] I> hdmi_enable, starting HDMI initialisation [0002.345] I> hdmi_enable, HDMI initialisation complete [0002.355] I> Load in CBoot Boot Options partition and parse it [0002.362] E> Error -9 when finding node with path /boot-configuration [0002.362] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO file. [0002.365] I> Using default boot order [0002.368] I> boot-dev-order :- [0002.371] I> 1.sd [0002.373] I> 2.usb [0002.375] I> 3.nvme [0002.377] I> 4.emmc [0002.379] I> 5.net [0002.381] I> Hit any key to stop autoboot: 4 3 2 1 [0004.388] initializing target [0004.388] calling apps_init() [0004.389] starting app kernel_boot_app [0004.408] I> found decompressor handler: lz4-legacy [0004.409] I> decompressing BMP blob ... [0004.420] I> Kernel type = Normal [0004.420] I> ########## SD (0) boot ########## [0004.421] I> No sdcard [0004.421] I> sdcard-0 params source = DT-BL [0004.421] E> Blockdev open: exit error [0004.421] E> SD boot failed, err: 724238353 [0004.422] I> ########## USB (0) boot ########## [0004.427] W> No valid slot number is found in scratch register [0004.427] W> Return default slot: _a [0004.436] I> Validate XUSB-FW ... [0004.436] I> T19x: Authenticate XUSB-FW (bin_type: 11), max size 0x28000 [0004.440] I> Encryption fuse is not ON [0004.443] I> USB Firmware Version: 60.09 release [0004.502] I> regulator of usb2-0 already enabled [0004.509] I> regulator of usb2-1 already enabled [0004.516] I> regulator of usb2-2 already enabled [0004.527] I> enabling 'vdd-5v-sata' regulator [0005.534] E> failed to initialize xhci controller [0005.534] E> Error in init of XUSB host driver, err: 79790026 [0005.534] W> Failed to initialize device 5-0 [0005.535] E> USB boot failed, err: 2037973030 [0005.535] I> ########## NVME (0) boot ########## [0005.535] I> Initializing nvme device instance 0 [0005.536] I> Initializing nvme controller [0005.540] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000 [0005.546] I> vpcie3v3-supply not found [0005.550] I> vpcie12v-supply not found [0005.553] W> Failed to get nvidia,plat-gpios [0005.557] I> tegrabl_pcie_soc_preinit: (0): [0005.561] I> Unpowergate [0005.564] I> tegrabl_car_clk_disable(0) ... [0005.568] I> tegrabl_car_rst_set(CORE, 0) ... [0005.572] I> tegrabl_car_rst_set(APB, 0) ... [0005.576] I> tegrabl_car_clk_enable(0) ... [0005.580] I> tegrabl_car_rst_clear(APB, 0) ... [0005.584] I> tegrabl_set_ctrl_state(0) [0005.588] I> CLR PCIE_APB:6 [0005.591] I> tegrabl_pcie_soc_init: (0): [0005.594] I> APPL initialization ... [0005.598] I> poweron phys [0005.600] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000 [0005.607] I> tegrabl_power_on_phy: power on phy @0x3e30000 [0005.612] I> tegrabl_power_on_phy: power on phy @0x3e40000 [0005.617] I> tegrabl_power_on_phy: power on phy @0x3e50000 [0005.623] I> tegrabl_power_on_phy: power on phy @0x3e60000 [0006.728] C> Failed to link up controller-0 [0006.728] I> PCIe (0) Link is not UP [0006.729] W> Failed tegrabl_pcie_soc_init(), error=0x12 [0006.730] I> Failed to initialize SoC Host PCIe controller [0006.730] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(0); error=0x12 [0006.730] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0006.734] W> Failed to open NVME-0, err = 80800612 [0006.739] W> Failed to initialize device 10-0 [0006.743] E> NVME (0) boot failed, err: 0x80800612 [0006.747] I> ########## NVME (1) boot ########## [0006.752] I> Initializing nvme device instance 1 [0006.756] I> Initializing nvme controller [0006.760] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14100000 [0006.767] I> vpcie3v3-supply not found [0006.770] I> vpcie12v-supply not found [0006.774] W> Failed to get nvidia,plat-gpios [0006.778] I> tegrabl_pcie_soc_preinit: (1): [0006.782] I> Unpowergate [0006.784] I> tegrabl_car_clk_disable(1) ... [0006.788] I> tegrabl_car_rst_set(CORE, 1) ... [0006.792] I> tegrabl_car_rst_set(APB, 1) ... [0006.797] I> tegrabl_car_clk_enable(1) ... [0006.801] I> tegrabl_car_rst_clear(APB, 1) ... [0006.805] I> tegrabl_set_ctrl_state(1) [0006.808] I> CLR PCIE_APB:6 [0006.811] I> tegrabl_pcie_soc_init: (1): [0006.815] I> APPL initialization ... [0006.818] I> poweron phys [0006.821] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14100000 [0006.827] I> tegrabl_power_on_phy: power on phy @0x3e10000 [0006.934] I> PCIe controller-1 link is up [0006.934] I> tegra_pcie_info[1].cfg0_base = 0x30000000 [0006.935] I> tegra_pcie_info[1].cfg1_base = 0x30020000 [0006.935] I> tegra_pcie_info[1].atu_dma_base = 0x30040000 [0006.935] I> tegra_pcie_bus[1].mem = 0x30200000 [0006.936] I> Scanning busnr: 0 devfn: 0 [0006.936] I> PCIe IDs: 0x1ad210de [0006.939] I> PCIe RID_CC: 0x60400a1 [0006.943] I> Scanning busnr: 1 devfn: 0 [0006.946] I> PCIe IDs: 0x91711b4b [0006.949] I> PCIe RID_CC: 0x1060113 [0006.953] I> PCI Config: I/O=0x30100000, Memory=0x30200000 [0006.958] I> IO bar_num=0 bar=0x30100000 [0006.962] I> IO bar_num=1 bar=0x30100008 [0006.966] I> IO bar_num=2 bar=0x30100010 [0006.969] I> IO bar_num=3 bar=0x30100018 [0006.973] I> IO bar_num=4 bar=0x30100020 [0006.977] I> MEM bar_num=5 bar=0x30200000 [0006.981] I> Number of PCIe devices detected: 2 [0006.985] E> tegrabl_nvme_init: Failed tegrabl_pcie_get_dev(1); error=0x0 [0006.992] I> PCIe (1) link is UP [0007.005] E> Link didn't transition to L2 state [0007.036] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0007.036] W> Failed to open NVME-1, err = 80800612 [0007.036] W> Failed to initialize device 10-1 [0007.037] E> NVME (1) boot failed, err: 0x80800612 [0007.037] I> ########## NVME (2) boot ########## [0007.037] I> Initializing nvme device instance 2 [0007.039] I> Initializing nvme controller [0007.044] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14120000 [0007.050] I> vpcie3v3-supply not found [0007.053] I> vpcie12v-supply not found [0007.057] W> Failed to get nvidia,plat-gpios [0007.061] I> tegrabl_pcie_soc_preinit: (2): [0007.065] I> Unpowergate [0007.067] I> tegrabl_car_clk_disable(2) ... [0007.071] I> tegrabl_car_rst_set(CORE, 2) ... [0007.076] I> tegrabl_car_rst_set(APB, 2) ... [0007.080] I> tegrabl_car_clk_enable(2) ... [0007.084] I> tegrabl_car_rst_clear(APB, 2) ... [0007.088] I> tegrabl_set_ctrl_state(2) [0007.091] I> CLR PCIE_APB:6 [0007.094] I> tegrabl_pcie_soc_init: (2): [0007.098] I> APPL initialization ... [0007.101] I> poweron phys [0007.104] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14120000 [0007.110] I> tegrabl_power_on_phy: controller 2 not available [0007.116] E> Failed to power on phy on controller-2 [0007.120] I> PCIe (2) Link is not UP [0007.124] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0007.129] I> Failed to initialize SoC Host PCIe controller [0007.134] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(2); error=0x1 [0007.141] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0007.147] W> Failed to open NVME-2, err = 80800601 [0007.152] W> Failed to initialize device 10-2 [0007.156] E> NVME (2) boot failed, err: 0x80800601 [0007.160] I> ########## NVME (3) boot ########## [0007.165] I> Initializing nvme device instance 3 [0007.169] I> Initializing nvme controller [0007.174] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14140000 [0007.180] I> vpcie3v3-supply not found [0007.183] I> vpcie12v-supply not found [0007.187] W> Failed to get nvidia,plat-gpios [0007.191] I> tegrabl_pcie_soc_preinit: (3): [0007.195] I> Unpowergate [0007.197] I> tegrabl_car_clk_disable(3) ... [0007.201] I> tegrabl_car_rst_set(CORE, 3) ... [0007.206] I> tegrabl_car_rst_set(APB, 3) ... [0007.210] I> tegrabl_car_clk_enable(3) ... [0007.214] I> tegrabl_car_rst_clear(APB, 3) ... [0007.218] I> tegrabl_set_ctrl_state(3) [0007.222] I> CLR PCIE_APB:6 [0007.224] I> tegrabl_pcie_soc_init: (3): [0007.228] I> APPL initialization ... [0007.231] I> poweron phys [0007.234] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14140000 [0007.240] I> tegrabl_power_on_phy: power on phy @0x3e80000 [0008.346] C> Failed to link up controller-3 [0008.346] I> PCIe (3) Link is not UP [0008.347] W> Failed tegrabl_pcie_soc_init(), error=0x12 [0008.347] I> Failed to initialize SoC Host PCIe controller [0008.347] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(3); error=0x12 [0008.348] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0008.351] W> Failed to open NVME-3, err = 80800612 [0008.356] W> Failed to initialize device 10-3 [0008.360] E> NVME (3) boot failed, err: 0x80800612 [0008.365] I> ########## NVME (4) boot ########## [0008.369] I> Initializing nvme device instance 4 [0008.374] I> Initializing nvme controller [0008.378] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14160000 [0008.384] I> vpcie3v3-supply not found [0008.388] I> vpcie12v-supply not found [0008.391] W> Failed to get nvidia,plat-gpios [0008.395] I> tegrabl_pcie_soc_preinit: (4): [0008.399] I> Unpowergate [0008.402] I> tegrabl_car_clk_disable(4) ... [0008.406] I> tegrabl_car_rst_set(CORE, 4) ... [0008.410] I> tegrabl_car_rst_set(APB, 4) ... [0008.414] I> tegrabl_car_clk_enable(4) ... [0008.418] I> tegrabl_car_rst_clear(APB, 4) ... [0008.422] I> tegrabl_set_ctrl_state(4) [0008.426] I> CLR PCIE_APB:6 [0008.429] I> tegrabl_pcie_soc_init: (4): [0008.432] I> APPL initialization ... [0008.436] I> poweron phys [0008.439] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14160000 [0008.444] I> tegrabl_power_on_phy: controller 4 not available [0008.450] E> Failed to power on phy on controller-4 [0008.455] I> PCIe (4) Link is not UP [0008.459] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0008.463] I> Failed to initialize SoC Host PCIe controller [0008.468] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(4); error=0x1 [0008.475] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0008.481] W> Failed to open NVME-4, err = 80800601 [0008.486] W> Failed to initialize device 10-4 [0008.490] E> NVME (4) boot failed, err: 0x80800601 [0008.495] I> ########## NVME (5) boot ########## [0008.499] I> Initializing nvme device instance 5 [0008.504] I> Initializing nvme controller [0008.508] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x141a0000 [0008.514] I> i=0, reg_phandle=0x1b [0008.519] I> reg_voltage=3300000 [0008.520] I> tegrabl_pcie_enable_regulators: regulator_set_voltage(0x1b, 3300000) [0008.532] I> enabling 'vdd-3v3-pcie' regulator [0008.532] I> i=1, reg_phandle=0x1c [0008.537] I> reg_voltage=1200000 [0008.538] I> tegrabl_pcie_enable_regulators: regulator_set_voltage(0x1c, 1200000) [0008.550] I> enabling 'vdd-12v-pcie' regulator [0008.550] I> tegrabl_pcie_soc_preinit: (5): [0008.554] I> Unpowergate [0008.557] I> tegrabl_car_clk_disable(5) ... [0008.560] I> tegrabl_car_rst_set(CORE, 5) ... [0008.565] I> tegrabl_car_rst_set(APB, 5) ... [0008.569] I> tegrabl_car_clk_enable(5) ... [0008.573] I> tegrabl_car_rst_clear(APB, 5) ... [0008.577] I> tegrabl_set_ctrl_state(5) [0008.580] I> CLR PCIE_APB:6 [0008.583] I> tegrabl_pcie_soc_init: (5): [0008.587] I> APPL initialization ... [0008.590] I> poweron phys [0008.593] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x141a0000 [0008.599] I> tegrabl_power_on_phy: power on phy @0x3eb0000 [0008.605] I> tegrabl_power_on_phy: power on phy @0x3ec0000 [0008.610] I> tegrabl_power_on_phy: power on phy @0x3ed0000 [0008.615] I> tegrabl_power_on_phy: power on phy @0x3ee0000 [0008.621] I> tegrabl_power_on_phy: power on phy @0x3ef0000 [0008.626] I> tegrabl_power_on_phy: power on phy @0x3f00000 [0008.631] I> tegrabl_power_on_phy: power on phy @0x3f10000 [0008.637] I> tegrabl_power_on_phy: power on phy @0x3f20000 [0009.742] C> Failed to link up controller-5 [0009.742] I> PCIe (5) Link is not UP [0009.743] I> tegrabl_pcie_disable_regulators: disable regulator 0x1b [0009.746] I> disabling 'vdd-3v3-pcie' regulator [0009.746] I> tegrabl_pcie_disable_regulators: disable regulator 0x1c [0009.749] I> disabling 'vdd-12v-pcie' regulator [0009.749] W> Failed tegrabl_pcie_soc_init(), error=0x12 [0009.751] I> Failed to initialize SoC Host PCIe controller [0009.756] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(5); error=0x12 [0009.762] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0009.769] W> Failed to open NVME-5, err = 80800612 [0009.773] W> Failed to initialize device 10-5 [0009.778] E> NVME (5) boot failed, err: 0x80800612 [0009.782] I> ########## Fixed storage boot ########## [0009.787] I> Loading kernel-bootctrl from partition [0009.792] I> Loading partition kernel-bootctrl at 0xa4ae0000 from device(0x1) [0009.805] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0009.806] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0009.819] I> Already published: 00010003 [0009.819] I> Look for boot partition [0009.820] I> Fallback: assuming 0th partition is boot partition [0009.826] I> Detect filesystem [0009.853] I> Loading extlinux.conf ... [0009.853] I> Loading extlinux.conf binary from rootfs ... [0009.854] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf [0009.890] I> Loading extlinux.conf sig file from rootfs ... [0009.891] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf.sig [0009.916] I> Validate extlinux.conf ... [0009.916] I> T19x: Authenticate extlinux.conf (bin_type: 54), max size 0x2000 [0009.916] I> Encryption fuse is not ON [0009.917] I> L4T boot options [0009.917] I> [1]: "primary kernel" [0009.917] I> Enter choice: [0012.919] I> Continuing with default option: 1 [0012.919] I> Loading kernel ... [0012.919] I> Loading kernel binary from rootfs ... [0012.920] I> rootfs path: /sdmmc_user/boot/Image [0013.143] I> Loading kernel sig file from rootfs ... [0013.143] I> rootfs path: /sdmmc_user/boot/Image.sig [0013.162] I> overload load_size to 34484232 (from 34484240) [0013.162] I> Validate kernel ... [0013.163] I> T19x: Authenticate kernel (bin_type: 37), max size 0x5000000 [0013.477] I> Encryption fuse is not ON [0013.492] I> Loading kernel-dtb ... [0013.493] I> No kernel-dtb binary path [0013.493] I> Continue to load from partition ... [0013.493] W> No valid slot number is found in scratch register [0013.494] W> Return default slot: _a [0013.494] I> A/B: bin_type (38) slot 0 [0013.494] I> Loading kernel-dtb from partition [0013.496] I> Loading partition kernel-dtb at 0x91000000 from device(0x1) [0013.510] I> Validate kernel-dtb ... [0013.511] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x400000 [0013.515] I> Encryption fuse is not ON [0013.517] I> Loading ramdisk from rootfs ... [0013.520] I> Loading ramdisk binary from rootfs ... [0013.525] I> rootfs path: /sdmmc_user/boot/initrd [0013.594] I> Loading ramdisk sig file from rootfs ... [0013.594] I> rootfs path: /sdmmc_user/boot/initrd.sig [0013.613] I> overload load_size to 7238358 (from 7238368) [0013.613] I> Validate ramdisk ... [0013.614] I> T19x: Authenticate ramdisk (bin_type: 54), max size 0x4000000 [0013.680] I> Encryption fuse is not ON [0013.687] I> Kernel hdr @0xa4ae0000 [0013.687] I> Kernel dtb @0x90000000 [0013.687] I> decompressor handler not found [0013.688] I> Copying kernel image (34484232 bytes) from 0xa4ae0000 to 0x80080000 ... [0013.694] I> Done [0013.695] I> Updated bpmp info to DTB [0013.696] I> Ramdisk: Base: 0x92000000; Size: 0x6e72d6 [0013.697] I> Updated initrd info to DTB [0013.697] W> WARN: Fail to override "console=none" in commandline [0013.700] I> Active rootfs suffix: [0013.703] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0013.710] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0013.718] W> No valid slot number is found in scratch register [0013.723] W> Return default slot: _a [0013.727] I> Active slot suffix: [0013.730] I> add_boot_slot_suffix: slot_suffix = [0013.735] I> Linux Cmdline: console=ttyTCU0,115200 video=tegrafb earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt rootfs.slot_suffix= tegra_fbmem=0x800000@0xa06aa000 lut_mem=0x2008@0xa06a5000 usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=8 boot.slot_suffix= boot.ratchetvalues=0.4.2 vpr_resize sdhci_tegra.en_boot_part_access=1 [0013.764] I> Updated bootarg info to DTB [0013.768] W> MAC addr invalid! [0013.771] E> Failed to get WIFI MAC address [0013.775] W> MAC addr invalid! [0013.778] E> Failed to get Bluetooth MAC address [0013.782] I> eeprom_get_mac_addr: MAC (type: 2): 48:b0:2d:63:d8:d0 [0013.789] W> "plugin-manager" doesn't exist, creating [0013.793] I> Adding /chosen/plugin-manager/cvm [0013.797] W> "chip-id" doesn't exist, creating [0013.802] I> Adding /chosen/plugin-manager/chip-id [0013.806] W> "configs" doesn't exist, creating [0013.810] I> Adding /chosen/plugin-manager/configs [0013.815] W> "ids" doesn't exist, creating [0013.819] I> Adding /chosen/plugin-manager/ids [0013.824] W> "odm-data" doesn't exist, creating [0013.828] I> Adding /chosen/plugin-manager/odm-data [0013.835] W> "memory" doesn't exist, creating [0013.837] I> [0] START: 0x80000000, END: 0xac000000 [0013.841] I> [1] START: 0xac004000, END: 0xf0ad0000 [0013.846] I> [2] START: 0xf0adc000, END: 0xf0ae0000 [0013.851] I> dram_block larger than 80000000 [0013.855] I> [3] START: 0x100000000, END: 0x880000000 [0013.860] I> added [base:0x80000000, size:0x2c000000] to /memory [0013.866] I> added [base:0xac200000, size:0x44800000] to /memory [0013.872] I> added [base:0x100000000, size:0x780000000] to /memory [0013.879] I> Updated memory info to DTB [0013.882] E> add_disp_param: failed to get display params for du=1 [0013.888] W> "reset" doesn't exist, creating [0013.892] I> Adding ecid(00000001642db1c01c00000013fd8240) to DT [0013.898] I> NVG: Logical CPU: 0; MPIDR: 0x80000000 [0013.902] I> NVG: Logical CPU: 1; MPIDR: 0x80000001 [0013.907] I> NVG: Logical CPU: 2; MPIDR: 0x80000100 [0013.911] I> NVG: Logical CPU: 3; MPIDR: 0x80000101 [0013.916] I> NVG: Logical CPU: 4; MPIDR: 0x80000200 [0013.921] I> NVG: Logical CPU: 5; MPIDR: 0x80000201 [0013.926] I> NVG: Logical CPU: 6; MPIDR: 0x80000300 [0013.930] I> NVG: Logical CPU: 7; MPIDR: 0x80000301 [0013.936] W> "misc-data" doesn't exist, creating [0013.940] I> Boot-device: eMMC [0013.942] I> Add boot-sdmmc to plugin-manager/misc-data [0013.948] I> Add storage-sdmmc to plugin-manager/misc-data [0013.953] W> Unknown storage device [0013.957] I> Add serial number:1420222030655 as DT property [0013.963] I> Plugin-manager override starting [0013.966] I> node /plugin-manager/fragement-tegra-wdt-en matches [0013.973] I> node /plugin-manager/fragement-soft-wdt matches [0013.981] I> node /plugin-manager/fragment-pcie-c5-rp matches [0013.985] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0013.998] I> Disable plugin-manager status in FDT [0013.998] I> Plugin-manager override finished successfully [0013.999] I> tegrabl_load_kernel_and_dtb: Done [0014.022] I> Kernel EP: 0x80080000, DTB: 0x90000000 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-tegra (buildbrain@mobile-u64-5403-d8000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Sat Feb 19 08:58:27 PST 2022 [ 0.000000] Boot CPU: AArch64 Processor [4e0f0040] [ 0.000000] OF: fdt:memory scan node memory, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 2c000000 [ 0.000000] OF: fdt: - ac200000 , 44800000 [ 0.000000] OF: fdt: - 100000000 , 780000000 [ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '') [ 0.000000] bootconsole [tegra_comb_uart0] enabled [ 0.000000] Found tegra_fbmem: 00800000@a06aa000 [ 0.000000] Found lut_mem: 00002008@a06a5000 ▒▒WARNING: pll_d3 has no dyn ramp ▒▒[ 6.632351] cgroup: cgroup2: unknown option "nsdelegate" [ 7.919274] random: crng init done [ 7.919424] random: 7 urandom warning(s) missed due to ratelimiting [ 7.932010] using random self ethernet address [ 7.932174] using random host ethernet address [ 8.508755] using random self ethernet address [ 8.508927] using random host ethernet address [ 8.944028] tegra-xudc-new 3550000.xudc: setup request failed: -22 [ 12.250397] Bridge firewalling registered Ubuntu 18.04.6 LTS user-desktop ttyTCU0 user-desktop login: