user@user-ubuntu:~$ sudo minicom [sudo] password for user: Welcome to minicom 2.7.1 OPTIONS: I18n Compiled on Aug 13 2017, 15:25:34. Port /dev/ttyUSB0, 14:22:16 Press CTRL-A Z for help on special keys [0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-dd84d362) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x10 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x903ec [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.178] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.198] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.233] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.280] Read PT from (2:0) [0000.296] Using BFS PT to query partitions [0000.301] Loading Tboot-CPU binary [0000.330] Verifying TBC in OdmNonSecureSBK mode [0000.340] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.347] Bootloader downloaded successfully. [0000.351] Downloaded Tboot-CPU binary to 0xa0000258 [0000.356] MAX77620_GPIO5 configured [0000.359] CPU power rail is up [0000.362] CPU clock enabled [0000.366] Performing RAM repair [0000.369] Updating A64 Warmreset Address to 0xa00002e9 [0000.374] BoardID = 3448, SKU = 0x0 [0000.377] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.381] Nano-SD: checking PT table on QSPI ... [0000.385] Loading NvTbootBootloaderDTB [0000.452] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.525] Bootloader DTB Load Address: 0x83000000 [0000.530] BoardID = 3448, SKU = 0x0 [0000.533] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.537] Nano-SD: checking PT table on QSPI ... [0000.541] Loading NvTbootKernelDTB [0000.607] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.680] Kernel DTB Load Address: 0x83100000 [0000.684] BoardID = 3448, SKU = 0x0 [0000.688] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.691] Nano-SD: checking PT table on QSPI ... [0000.698] Loading cboot binary [0000.813] Verifying EBT in OdmNonSecureSBK mode [0000.855] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.862] Bootloader downloaded successfully. [0000.866] BoardID = 3448, SKU = 0x0 [0000.870] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.873] Nano-SD: checking PT table on QSPI ... [0000.878] PT: Partition NCT NOT found ! [0000.882] Warning: Find Partition via PT Failed [0000.886] Next binary entry address: 0x92c00258 [0000.891] BoardId: 3448 [0000.895] Overriding pmu board id with proc board id [0000.900] Display board id is not available [0000.904] BoardID = 3448, SKU = 0x0 [0000.907] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.911] Nano-SD: checking PT table on QSPI ... [0001.016] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.073] /bpmp deleted [0001.075] SC7EntryFw header found loaded at 0xff700000 [0001.270] OVR2 PMIC [0001.272] Bpmp FW successfully loaded [0001.276] BoardID = 3448, SKU = 0x0 [0001.279] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.283] Nano-SD: checking PT table on QSPI ... [0001.288] WB0 init successfully at 0xff780000 [0001.293] Set NvDecSticky Bits [0001.296] GSC2 address ff53fffc value c0edbbcc [0001.302] GSC MC Settings done [0001.305] BoardID = 3448, SKU = 0x0 [0001.309] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.312] Nano-SD: checking PT table on QSPI ... [0001.318] TOS Image length 53680 [0001.321] Monitor size 53680 [0001.324] OS size 0 [0001.339] Secure Os AES-CMAC Verification Success! [0001.343] TOS image cipher info: plaintext [0001.347] Loading and Validation of Secure OS Successful [0001.363] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.368] NvTbootPackSdramParams: start. [0001.373] NvTbootPackSdramParams: done. [0001.377] Tegraboot started after 51833 us [0001.381] Basic modules init took 886376 us [0001.385] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.390] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.396] Next stage binary read took 102860 us [0001.400] Carveout took -126357 us [0001.403] CPU initialization took 495389 us [0001.407] Total time taken by TegraBoot 1358268 us [0001.412] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 08:53:41, Jul 9 2021 ERROR: Error initializing runtime service trusty_fast [0001.534] RamCode = 0 [0001.539] LPDDR4 Training: Read DT: Number of tables = 2 [0001.544] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.557] EMC Training Successful [0001.560] 408000 not found in DVFS table [0001.566] RamCode = 0 [0001.570] DT Write: emc-table@204000 succeeded [0001.575] DT Write: emc-table@1600000 succeeded [0001.579] LPDDR4 Training: Write DT: Number of tables = 2 [0001.626] [0001.627] Debug Init done [0001.630] Marked DTB cacheable [0001.633] Bootloader DTB loaded at 0x83000000 [0001.637] Marked DTB cacheable [0001.640] Kernel DTB loaded at 0x83100000 [0001.644] DeviceTree Init done [0001.657] Pinmux applied successfully [0001.662] gicd_base: 0x50041000 [0001.665] gicc_base: 0x50042000 [0001.668] Interrupts Init done [0001.672] Using base:0x60005090 & irq:208 for tick-timer [0001.677] Using base:0x60005098 for delay-timer [0001.682] platform_init_timer: DONE [0001.685] Timer(tick) Init done [0001.689] osc freq = 38400 khz [0001.693] [0001.694] Welcome to L4T Cboot [0001.697] [0001.698] Cboot Version: 00.00.2018.01-t210-39562017 [0001.703] calling constructors [0001.706] initializing heap [0001.709] initializing threads [0001.712] initializing timers [0001.715] creating bootstrap completion thread [0001.719] top of bootstrap2() [0001.722] CPU: ARM Cortex A57 [0001.725] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.729] initializing platform [0001.737] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.742] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.746] Macronix QSPI chip present [0001.750] SPI device register [0001.752] init boot device [0001.755] allocating memory for boot device(SPI) [0001.760] registering boot device [0001.778] QSPI bdev is already initialized [0001.782] Enable APE clock [0001.784] Un-powergate APE partition [0001.788] of_register: registering tegra_udc to of_hal [0001.793] of_register: registering inv20628-driver to of_hal [0001.799] of_register: registering ads1015-driver to of_hal [0001.804] of_register: registering lp8557-bl-driver to of_hal [0001.810] of_register: registering bq2419x_charger to of_hal [0001.816] of_register: registering bq27441_fuel_gauge to of_hal [0001.827] gpio framework initialized [0001.831] of_register: registering tca9539_gpio to of_hal [0001.836] of_register: registering tca9539_gpio to of_hal [0001.841] of_register: registering i2c_bus_driver to of_hal [0001.847] of_register: registering i2c_bus_driver to of_hal [0001.853] of_register: registering i2c_bus_driver to of_hal [0001.858] pmic framework initialized [0001.862] of_register: registering max77620_pmic to of_hal [0001.867] regulator framework initialized [0001.871] of_register: registering tps65132_bl_driver to of_hal [0001.877] initializing target [0001.883] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.891] board ID = D78, board SKU = 0 [0001.895] Skipping Z3! [0001.899] fixed regulator driver initialized [0001.917] initializing OF layer [0001.920] NCK carveout not present [0001.923] Skipping dts_overrides [0001.928] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.945] I2C Bus Init done [0001.947] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.958] I2C Bus Init done [0001.960] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.971] I2C Bus Init done [0001.973] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.984] I2C Bus Init done [0001.986] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.997] I2C Bus Init done [0001.999] of_children_init: Ops found for compatible string maxim,max77620 [0002.010] max77620_init using irq 118 [0002.015] register 'maxim,max77620' pmic [0002.019] gpio_driver_register: register 'max77620-gpio' driver [0002.025] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.036] I2C Bus Init done [0002.039] NCK carveout not present [0002.049] Find /i2c@7000c000's alias i2c0 [0002.053] get eeprom at 1-a0, size 256, type 0 [0002.062] Find /i2c@7000c500's alias i2c2 [0002.066] get eeprom at 3-a0, size 256, type 0 [0002.070] get eeprom at 3-ae, size 256, type 0 [0002.075] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.080] I2C slave not started [0002.083] I2C write failed [0002.085] Writing offset failed [0002.089] eeprom_init: EEPROM read failed [0002.092] pm_ids_update: eeprom init failed [0002.097] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.127] pm_ids_update: The pm board id is 3448-0000-402 [0002.133] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.142] pm_ids_update: pm id update successful [0002.146] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.177] pm_ids_update: The pm board id is 3449-0000-400 [0002.183] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.191] pm_ids_update: pm id update successful [0002.221] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.227] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.235] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.241] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.249] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3c:b0:bb [0002.255] Plugin Manager: Parse ODM data 0x000a4000 [0002.268] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.283] Find /i2c@7000c000's alias i2c0 [0002.286] get eeprom at 1-a0, size 256, type 0 [0002.295] Find /i2c@7000c500's alias i2c2 [0002.299] get eeprom at 3-a0, size 256, type 0 [0002.304] get eeprom at 3-ae, size 256, type 0 [0002.308] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.313] I2C slave not started [0002.316] I2C write failed [0002.319] Writing offset failed [0002.322] eeprom_init: EEPROM read failed [0002.326] pm_ids_update: eeprom init failed [0002.330] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.360] pm_ids_update: The pm board id is 3448-0000-402 [0002.366] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.373] pm_ids_update: pm id update successful [0002.378] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.408] pm_ids_update: The pm board id is 3449-0000-400 [0002.414] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.421] pm_ids_update: pm id update successful [0002.451] Add serial number:1420821029663 as DT property [0002.459] Applying platform configs [0002.466] platform-init is not present. Skipping [0002.470] calling apps_init() [0002.476] Couldn't find GPT header [0002.481] Proceeding to Cold Boot [0002.484] starting app android_boot_app [0002.488] Device state: unlocked [0002.491] display console init [0002.499] could not find regulator [0002.503] hdmi cable connected [0002.518] edid read success [0002.521] width = 640, height = 480, frequency = 25174825 [0002.526] width = 640, height = 480, frequency = 25174825 [0002.531] width = 640, height = 48DT entry for leds-pwm not found 0[0002.541] , frequency = 25174825 [0002.544] width = 1920, height = 1080, frequency = 148500000 [0002.550] width = 1600, height = 900, frequency = 97750000 [0002.555] Best mode Width = 640, Height = 480, freq = 25174825 [0002.563] tmds-config node not found [0002.567] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.582] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.589] could not find regulator [0002.592] could not find regulator [0002.596] could not find regulator [0002.624] using default cmu settings [0002.628] dc_hdmi_enable, starting HDMI initialisation [0002.634] dc_hdmi_enable, HDMI initialisation complete [0002.639] list and configure display window [0002.644] display console init completed [0002.651] subnode volume_up is not found ! [0002.655] subnode back is not found ! [0002.659] subnode volume_down is not found ! [0002.663] subnode menu is not found ! [0002.667] Gpio keyboard init success [0002.747] found decompressor handler: lz4-legacy [0002.762] decompressing blob (type 1)... [0002.829] load_bmp_blob: panelresolution=480 type=0 [0002.903] decompressor handler not found [0002.907] load_firmware_blob: Firmware blob loaded, entries=2 [0002.913] XUSB blob version 0 size 124416 @ 0x92dee28c [0002.919] -------> se_aes_verify_sbk_clear: 747 [0002.923] se_aes_verify_sbk_clear: Error [0002.927] SE operation failed [0002.930] bl_battery_charging: connected to external power supply [0002.942] device_query_partition_size: failed to open partition spiflash0:MSC ! [0002.949] MSC Partition not found [0002.956] device_query_partition_size: failed to open partition spiflash0:USP ! [0002.963] USP partition read failed! [0002.966] blob_init: blob-partition USP header read failed [0002.972] android_boot Unable to update recovery partition [0002.977] kfs_getpartname: name = LNX [0002.981] Loading kernel from LNX [0002.990] Found 19 BFS partitions in "spiflash0" [0003.309] load kernel from storage [0003.314] decompressor handler not found [0003.578] Successfully loaded kernel and ramdisk images [0003.584] board ID = D78, board SKU = 0 [0003.588] sdmmc node status = okay [0003.591] sdcard instance = 0 [0003.594] sdcard gpio handle 0x5b [0003.598] sdcard gpio pin 0xc9 [0003.600] sdcard gpio flags 0x0 [0003.604] vmmc-supply 0x9e [0003.606] cd_gpio_pin = 201 [0003.609] pin_state = 1 [0003.611] No sdcard [0003.613] SD-card NOT present ... [0003.616] load_and_boot_kernel: SD card not detected! [0003.622] load_bmp_blob: panelresolution=480 type=0 [0003.627] get_bmp: Required BMP 7 with resolution type=0 not found [0003.634] SDcard warning bmp failed! [0003.638] load_bmp_blob: panelresolution=480 type=0 [0003.712] display bmp image done [0003.715] NCK carveout not present [0003.718] Skipping dts_overrides [0003.721] NCK carveout not present [0003.731] Find /i2c@7000c000's alias i2c0 [0003.735] get eeprom at 1-a0, size 256, type 0 [0003.744] Find /i2c@7000c500's alias i2c2 [0003.748] get eeprom at 3-a0, size 256, type 0 [0003.752] get eeprom at 3-ae, size 256, type 0 [0003.756] pm_ids_update: Updating 1,a0, size 256, type 0 [0003.762] I2C slave not started [0003.765] I2C write failed [0003.767] Writing offset failed [0003.770] eeprom_init: EEPROM read failed [0003.774] pm_ids_update: eeprom init failed [0003.778] pm_ids_update: Updating 3,a0, size 256, type 0 [0003.808] pm_ids_update: The pm board id is 3448-0000-402 [0003.815] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0003.824] pm_ids_update: pm id update successful [0003.828] pm_ids_update: Updating 3,ae, size 256, type 0 [0003.858] pm_ids_update: The pm board id is 3449-0000-400 [0003.865] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0003.872] pm_ids_update: pm id update successful [0003.903] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.909] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0003.917] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.922] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0003.931] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3c:b0:bb [0003.937] Plugin Manager: Parse ODM data 0x000a4000 [0003.949] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0003.958] Add serial number:1420821029663 as DT property [0003.967] "bpmp" doesn't exist, creating [0003.972] Updated bpmp info to DTB [0003.977] Updated initrd info to DTB [0003.981] "proc-board" doesn't exist, creating [0003.987] Updated board info to DTB [0003.990] "pmu-board" doesn't exist, creating [0003.996] Updated board info to DTB [0003.999] "display-board" doesn't exist, creating [0004.005] Updated board info to DTB [0004.009] "reset" doesn't exist, creating [0004.013] Updated reset info to DTB [0004.017] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 [0004.056] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.062] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0004.075] Updated bootarg info to DTB [0004.078] Adding uuid 00000001642e12c30c0000000d010580 to DT [0004.084] Adding eks info 0 to DT [0004.090] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.096] Updated memory info to DTB [0004.104] set vdd_core voltage to 1125 mv [0004.108] setting 'vdd-core' regulator to 1125000 micro volts [0004.113] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Jul 09 2021 - 08:53:46 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 MMC: no card present Card did not respond to voltage select! starting USB... Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 Bus xusb@70090000: Firmware size 124416 Firmware timestamp: 0x5da88fc3, Version: 50.25 release Register HCSParams1: 9000124 NbrPorts: 9 Starting the controller USB XHCI 1.00 scanning bus xusb@70090000 for devices... 6 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: Samsung Rev: 1100 Prod: Flash Drive FIT Type: Removable Hard Disk Capacity: 244752.5 MB = 239.0 GB (501253132 x 512) ... is now current device Scanning usb 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 831 bytes read in 2 ms (405.3 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7159329 bytes read in 32 ms (213.4 MiB/s) Retrieving file: /boot/arducam/Image 34404360 bytes read in 141 ms (232.7 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=PARTUUID=17c0943d-d8d6-47aa-b945-dce49ad99fd4 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 test_usb ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317e68d copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (jenkins@feaf98b9a84d) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Oct 15 02:34:21 UTC 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00140000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=PARTUUID=17c0943d-d8d6-47aa-b945-dce49ad99fd4 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 test_usb [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29228(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3567220K/4159488K available (15294K kernel code, 2942K rwdata, 6724K rodata, 8576K init, 609K bss, 117132K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009610000 ( 6784 KB) [ 0.000000] .init : 0xffffff8009610000 - 0xffffff8009e70000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e70000 - 0xffffff800a14f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a14f808 - 0xffffff800a1e7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] PLL_RE already enabled. Postponing set full defaults [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.010014] Console: colour dummy device 80x25 [ 0.014667] console [tty0] enabled [ 0.018182] bootconsole [uart8250] disabled [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (jenkins@feaf98b9a84d) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Oct 15 02:34:21 UTC 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00140000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=PARTUUID=17c0943d-d8d6-47aa-b945-dce49ad99fd4 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 test_usb [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29228(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3567220K/4159488K available (15294K kernel code, 2942K rwdata, 6724K rodata, 8576K init, 609K bss, 117132K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009610000 ( 6784 KB) [ 0.000000] .init : 0xffffff8009610000 - 0xffffff8009e70000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e70000 - 0xffffff800a14f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a14f808 - 0xffffff800a1e7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] PLL_RE already enabled. Postponing set full defaults [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.010014] Console: colour dummy device 80x25 [ 0.014667] console [tty0] enabled [ 0.018182] bootconsole [uart8250] disabled [ 0.022507] kmemleak: Kernel memory leak detector disabled [ 0.022536] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.022557] pid_max: default: 32768 minimum: 301 [ 0.023021] Security Framework initialized [ 0.023249] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.023263] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.024383] ftrace: allocating 47233 entries in 185 pages [ 0.193730] ASID allocator initialised with 65536 entries [ 0.232284] tegra-id: chipid=22117. [ 0.232313] tegra-id: opt_subrevision=0. [ 0.232336] Tegra Speedo/IDDQ fuse revision 4 [ 0.232347] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.232357] Tegra: CPU Process ID 0, SoC Process ID 0, GPU Process ID 0 [ 0.232369] Tegra: CPU Speedo Value 2020, SoC Speedo Value 1907, GPU Speedo Value 2024 [ 0.232380] Tegra: CPU IDDQ Value 1760, SoC IDDQ Value 2000, GPU IDDQ Value 2380 [ 0.232406] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 0 [ 0.232428] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.232490] DTB Build time: Jul 9 2021 08:58:42 [ 0.281289] CPU1: Booted secondary processor [411fd071] [ 0.313183] CPU2: Booted secondary processor [411fd071] [ 0.345171] CPU3: Booted secondary processor [411fd071] [ 0.345265] Brought up 4 CPUs [ 0.345320] SMP: Total of 4 processors activated. [ 0.345336] CPU features: detected feature: 32-bit EL0 Support [ 0.345607] CPU: All CPU(s) started at EL2 [ 0.345636] alternatives: patching kernel code [ 0.353828] devtmpfs: initialized [ 0.392537] Initilizing CustomIPI irq domain [ 0.392967] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.393009] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.403658] pinctrl core: initialized pinctrl subsystem [ 0.404275] OS set in device tree is not L4T. [ 0.404724] regulator-dummy: no parameters [ 0.405008] Initializing plugin-manager [ 0.405178] Plugin module not found [ 0.405409] node /plugin-manager/fragement@0 match with board >=3448-0000-100 [ 0.405934] node /plugin-manager/fragment@1 match with board >=3448-0000-101 [ 0.406942] node /plugin-manager/fragement@7 match with odm-data enable-pmic-wdt [ 0.407168] node /plugin-manager/fragement@8 match with odm-data enable-pmic-wdt [ 0.407777] node /plugin-manager/fragement@10 match with board >=3448-0000-300 [ 0.409788] node /plugin-manager/fragement@13 match with board >=3448-0000-300 [ 0.413542] NET: Registered protocol family 16 [ 0.414990] pstore: using zlib compression [ 0.415511] console [pstore-1] enabled [ 0.415525] pstore: Registered ramoops as persistent store backend [ 0.415543] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.429304] cpuidle: using governor menu [ 0.433753] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.435577] vdso: 2 pages (1 code @ ffffff8008f77000, 1 data @ ffffff8009e74000) [ 0.435619] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.437831] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.440367] Serial: AMBA PL011 UART driver [ 0.440878] tegra_powergate_init: DONE [ 0.440908] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.440944] DTB Build time: Jul 9 2021 08:58:42 [ 0.443027] Tegra reboot handler registered. [ 0.447623] iommu: Adding device tegra-carveouts to group 0 [ 0.447791] platform tegra-carveouts: domain=ffffffc0f942a3d8 allocates as[0]=ffffffc0f9bcc0a8 [ 0.448165] iommu: Adding device smmu_test to group 1 [ 0.448234] platform smmu_test: domain=ffffffc0f942a618 allocates as[0]=ffffffc0f9bcc110 [ 0.449079] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.449155] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.449228] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.449251] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.449308] mc-err: mcerr ops are set to t21x [ 0.459672] iommu: Adding device 70090000.xusb to group 2 [ 0.460010] iommu: Adding device 70006000.serial to group 3 [ 0.460089] platform 70006000.serial: domain=ffffffc0f946ecd8 allocates as[0]=ffffffc0f9bcc178 [ 0.460539] iommu: Adding device 70006040.serial to group 4 [ 0.460821] iommu: Adding device 70006200.serial to group 5 [ 0.461025] iommu: Adding device sound to group 6 [ 0.461094] platform sound: domain=ffffffc0f94f3258 allocates as[0]=ffffffc0f9bcc1e0 [ 0.461735] iommu: Adding device 7000d400.spi to group 7 [ 0.462016] iommu: Adding device 7000d600.spi to group 8 [ 0.462329] iommu: Adding device 70410000.spi to group 9 [ 0.462642] iommu: Adding device 50000000.host1x to group 10 [ 0.462935] iommu: Adding device 54080000.vi to group 11 [ 0.463341] iommu: Adding device 54600000.isp to group 12 [ 0.463611] iommu: Adding device 54680000.isp to group 13 [ 0.463902] iommu: Adding device tegradc.0 to group 14 [ 0.463963] platform tegradc.0: domain=ffffffc0f94ff198 allocates as[0]=ffffffc0f9bcc248 [ 0.465400] platform tegradc.0: IOVA linear map 0x0000000092ca9000(140000) [ 0.465810] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.466167] iommu: Adding device tegradc.1 to group 15 [ 0.466230] platform tegradc.1: domain=ffffffc0f94ff3d8 allocates as[0]=ffffffc0f9bcc2b0 [ 0.467638] platform tegradc.1: IOVA linear map 0x0000000092ca9000(140000) [ 0.468041] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.468326] iommu: Adding device 54340000.vic to group 16 [ 0.468541] iommu: Adding device 544c0000.nvenc to group 17 [ 0.468745] iommu: Adding device 54500000.tsec to group 18 [ 0.468955] iommu: Adding device 54100000.tsecb to group 19 [ 0.469173] iommu: Adding device 54480000.nvdec to group 20 [ 0.469400] iommu: Adding device 54380000.nvjpg to group 21 [ 0.470446] iommu: Adding device 546c0000.i2c to group 22 [ 0.470800] iommu: Adding device 57000000.gpu to group 23 [ 0.470865] platform 57000000.gpu: domain=ffffffc0f958a3d8 allocates as[0]=ffffffc0f9bcc318 [ 0.470941] platform 57000000.gpu: domain=ffffffc0f958a3d8 allocates as[1]=ffffffc0f9bcc380 [ 0.470997] platform 57000000.gpu: domain=ffffffc0f958a3d8 allocates as[2]=ffffffc0f9bcc3e8 [ 0.471048] platform 57000000.gpu: domain=ffffffc0f958a3d8 allocates as[3]=ffffffc0f9bcc450 [ 0.471964] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.472001] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.472028] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [ 0.472046] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.472064] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.521483] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.521515] tegra-pmc: Clear bootloader IO dpd settings [ 0.521548] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.521623] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.521931] iommu: Adding device 70012000.se to group 24 [ 0.522719] iommu: Adding device 7000c000.i2c to group 25 [ 0.522987] iommu: Adding device 7000c400.i2c to group 26 [ 0.523244] iommu: Adding device 7000c500.i2c to group 27 [ 0.523516] iommu: Adding device 7000c700.i2c to group 28 [ 0.523790] iommu: Adding device 7000d000.i2c to group 29 [ 0.524056] iommu: Adding device 7000d100.i2c to group 30 [ 0.524355] iommu: Adding device sdhci-tegra.0 to group 31 [ 0.524428] platform sdhci-tegra.0: domain=ffffffc0f9599558 allocates as[0]=ffffffc0f9bcc4b8 [ 0.525331] iommu: Adding device 700d0000.xudc to group 32 [ 0.528534] vdd-ac-bat: 5000 mV [ 0.528898] vdd-5v0-sys: 5000 mV [ 0.529910] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.529977] vdd-5v0-hdmi: 5000 mV [ 0.530387] vdd-1v8-sys: 1800 mV [ 0.530838] vdd-fan: supplied by vdd-5v0-sys [ 0.530897] vdd-fan: 5000 mV [ 0.531298] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.531346] vdd-usb-vbus: 5000 mV [ 0.531887] vdd-usb-vbus2: 5000 mV [ 0.558100] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.560543] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.562434] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.562477] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.562526] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.562904] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.570797] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.571177] SCSI subsystem initialized [ 0.571691] usbcore: registered new interface driver usbfs [ 0.571766] usbcore: registered new interface driver hub [ 0.571853] usbcore: registered new device driver usb [ 0.576370] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.580577] vdd-core: 600 <--> 1162 mV at 1125 mV [ 0.580753] random: fast init done [ 0.581660] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.584543] vdd-ddr-1v1: 1150 mV [ 0.588466] vdd-pre-reg-1v35: 1350 mV [ 0.592465] vdd-1v8: 1800 mV [ 0.596466] avdd-sys-1v2: 1200 mV [ 0.600467] vdd-pex-1v0: 1050 mV [ 0.601153] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.601719] max77620-ldo3: at 3100 mV [ 0.604469] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.605025] max77620-ldo5: at 3100 mV [ 0.608472] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [ 0.612465] avdd-1v05-pll: 1050 mV [ 0.616464] avdd-io-hdmi-dp: 1050 mV [ 0.619101] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.619435] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.619751] max77620 4-003c: max77620 probe successful [ 0.622483] media: Linux media interface: v0.10 [ 0.622554] Linux video capture interface: v2.00 [ 0.623525] pps_core: LinuxPPS API ver. 1 registered [ 0.623549] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.623590] PTP clock support registered [ 0.626974] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.627872] Advanced Linux Sound Architecture Driver Initialized. [ 0.628536] Bluetooth: Core ver 2.22 [ 0.628602] NET: Registered protocol family 31 [ 0.628620] Bluetooth: HCI device and connection manager initialized [ 0.628646] Bluetooth: HCI socket layer initialized [ 0.628666] Bluetooth: L2CAP socket layer initialized [ 0.628702] Bluetooth: SCO socket layer initialized [ 0.630454] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.630488] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.630555] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.630582] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.634336] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.635623] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.635731] vdd-3v3-sys: 3300 mV [ 0.636018] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.636546] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.637029] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.637093] vdd-3v3-sd: 3300 mV [ 0.638217] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.638276] avdd-io-edp-1v05: 1050 mV [ 0.638721] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.638770] vdd-usb-hub-en: 5000 mV [ 0.640097] camchar: rtcpu character device driver loaded [ 0.640938] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [ 0.642357] clocksource: Switched to clocksource arch_sys_counter [ 0.682799] VFS: Disk quotas dquot_6.6.0 [ 0.682979] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.683469] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.683908] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.683953] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.684164] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.684185] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.684210] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.684255] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.684280] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.684309] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.684330] nvmap_page_pool_init: Total RAM pages: 1010589 [ 0.684347] nvmap_page_pool_init: nvmap page pool size: 126323 pages (493 MB) [ 0.684452] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.684891] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.685837] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.694047] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.694561] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.694964] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.695264] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.695468] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.695766] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.695783] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.696224] NET: Registered protocol family 2 [ 0.697273] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.697509] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.698013] TCP: Hash tables configured (established 32768 bind 32768) [ 0.698180] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.698277] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.698784] NET: Registered protocol family 1 [ 0.699479] RPC: Registered named UNIX socket transport module. [ 0.699505] RPC: Registered udp transport module. [ 0.699521] RPC: Registered tcp transport module. [ 0.699536] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.699817] Trying to unpack rootfs image as initramfs... [ 1.002660] Freeing initrd memory: 6988K [ 1.012646] host1x 50000000.host1x: initialized [ 1.014609] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.017866] audit: initializing netlink subsys (disabled) [ 1.017956] audit: type=2000 audit(0.855:1): initialized [ 1.018795] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.028615] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.030115] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.030968] 9p: Installing v9fs 9p2000 file system support [ 1.034219] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 1.034418] io scheduler noop registered [ 1.034728] io scheduler cfq registered (default) [ 1.037452] gic 702f9000.agic: GIC IRQ controller registered [ 1.040596] iommu: Adding device 702ef000.adsp to group 33 [ 1.049584] iommu: Adding device aconnect@702c0000:adsp_audio to group 34 [ 1.049762] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 1.050435] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x9248412 [ 1.050467] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 1.052164] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 1.052297] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 1.052418] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 1.052623] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 1.052734] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 1.052837] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 1.052942] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 1.053044] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 1.053151] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 1.053254] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 1.059379] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 1.061143] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 1.063149] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.064413] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 1.064759] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.066005] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.066254] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 1.066502] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 1.066705] Adding domain tsec-pd to PM domain host1x-pd [ 1.070158] tsec 54500000.tsec: initialized [ 1.071608] tsec 54100000.tsecb: initialized [ 1.072358] Adding domain nvdec-pd to PM domain host1x-pd [ 1.076025] nvdec 54480000.nvdec: initialized [ 1.077119] Adding domain vic03-pd to PM domain host1x-pd [ 1.077314] Adding domain msenc-pd to PM domain host1x-pd [ 1.077486] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.081643] falcon 54340000.vic: initialized [ 1.082941] falcon 544c0000.nvenc: initialized [ 1.084277] falcon 54380000.nvjpg: initialized [ 1.088871] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97 [ 1.088951] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.088983] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.089000] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.089111] display board info: id 0x0, fab 0x0 [ 1.089181] generic_infoframe_type: 0x87 [ 1.089269] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.089289] tegra_cec 70015000.tegra_cec: probed [ 1.089328] tegradc tegradc.0: DT parsed successfully [ 1.089393] tegradc tegradc.0: Display dc.ffffff800ab80000 registered with id=0 [ 1.089934] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 640x480 (on 0x0mm) pclk=25173906 [ 1.097096] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.098232] tegradc tegradc.0: probed [ 1.103647] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.105165] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check disabled [ 1.105202] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.105731] kfuse 7000fc00.kfuse: initialized [ 1.107352] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.108454] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.110007] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.110049] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.110629] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.112237] vdd-gpu: applied init 1000000uV constraint [ 1.112269] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.112736] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.117561] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.117729] No Device Node present for smmu client: serial8250 !! [ 1.117760] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.117840] iommu: Adding device serial8250 to group 35 [ 1.119563] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 1.119597] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.119617] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 1.119637] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 1.119661] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.123181] console [ttyS0] disabled [ 1.123284] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.160309] pci 0000:00:01.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [ 1.160315] pci 0000:00:02.0: BAR 14: assigned [mem 0x13100000-0x131fffff] [ 1.160320] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.160330] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 1.160356] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.160364] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 1.160375] pci 0000:02:00.0: BAR 4: assigned [mem 0x13100000-0x13103fff 64bit] [ 1.160395] pci 0000:02:00.0: BAR 2: assigned [mem 0x13104000-0x13104fff 64bit] [ 1.160413] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 1.160422] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.160426] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 1.160432] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 1.160967] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt [ 1.160972] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 1.161324] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 1.161329] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 2.110396] tegra_cec 70015000.tegra_cec: Can't find physical addresse. [ 2.110400] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 3.615096] console [ttyS0] enabled [ 3.615450] Console: switching to colour frame buffer device 80x30 [ 3.619593] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 3.619931] serial-tegra 70006200.serial: RX in PIO mode [ 3.620025] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 3.621034] [drm] Initialized [ 3.651949] tegradc tegradc.0: fb registered [ 3.655423] brd: module loaded [ 3.663158] loop: module loaded [ 3.666461] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [ 3.666465] tegra_profiler: version: 1.143, samples/io: 48/28 [ 3.666587] tegra_profiler: auth: init [ 3.667796] THERMAL EST: found 2 subdevs [ 3.667802] THERMAL EST num_resources: 0 [ 3.667809] [THERMAL EST subdev 0] [ 3.667816] [THERMAL EST subdev 1] [ 3.668285] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 3.668287] THERMAL EST: thz register success. [ 3.668471] THERMAL EST: end of probe, return err: 0 [ 3.669653] sd: No Scsi addr parsed to reserve index [ 3.669689] hisi_sas: driver version v1.6 [ 3.674627] tegra-qspi 70410000.spi: Prod settings list not found [ 3.675782] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes) [ 3.675790] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0 [ 3.679546] libphy: Fixed MDIO Bus: probed [ 3.680278] tun: Universal TUN/TAP device driver, 1.6 [ 3.680281] tun: (C) 1999-2004 Max Krasnyansky [ 3.681570] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 3.681575] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.681628] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 3.681630] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.681689] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 3.681692] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.681736] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 3.681739] Copyright(c) 1999 - 2017 Intel Corporation. [ 3.683114] r8168 0000:02:00.0: enabling device (0000 -> 0003) [ 3.683144] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 3.697336] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 3.697479] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 48:b0:2d:3c:b0:bb from device tree [ 3.698090] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 3.698150] r8168 Copyright (C) 2017 Realtek NIC software team [ 3.698150] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 3.698150] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 3.698792] PPP generic driver version 2.4.2 [ 3.699001] PPP BSD Compression module registered [ 3.699006] PPP Deflate Compression module registered [ 3.699046] PPP MPPE Compression module registered [ 3.699053] NET: Registered protocol family 24 [ 3.699128] usbcore: registered new interface driver r8152 [ 3.699187] usbcore: registered new interface driver asix [ 3.699246] usbcore: registered new interface driver ax88179_178a [ 3.699282] usbcore: registered new interface driver cdc_ether [ 3.699319] usbcore: registered new interface driver net1080 [ 3.699356] usbcore: registered new interface driver cdc_subset [ 3.699399] usbcore: registered new interface driver zaurus [ 3.699451] usbcore: registered new interface driver cdc_ncm [ 3.699649] VFIO - User Level meta-driver version: 0.3 [ 3.700969] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.700993] ehci-pci: EHCI PCI platform driver [ 3.701041] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.701054] ohci-pci: OHCI PCI platform driver [ 3.701096] ohci-platform: OHCI generic platform driver [ 3.704460] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 3.705056] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 3.706208] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f90adc00 id [ 3.708535] usbcore: registered new interface driver uas [ 3.708604] usbcore: registered new interface driver usb-storage [ 3.708736] usbcore: registered new interface driver usbserial [ 3.709107] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release [ 3.709158] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.709185] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 3.709960] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 3.710017] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 3.710216] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.710223] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.710227] usb usb1: Product: xHCI Host Controller [ 3.710231] usb usb1: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 3.710234] usb usb1: SerialNumber: 70090000.xusb [ 3.710879] hub 1-0:1.0: USB hub found [ 3.710930] hub 1-0:1.0: 5 ports detected [ 3.711592] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.711602] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 3.711758] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.711860] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 3.711865] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.711869] usb usb2: Product: xHCI Host Controller [ 3.711873] usb usb2: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 3.711876] usb usb2: SerialNumber: 70090000.xusb [ 3.712466] hub 2-0:1.0: USB hub found [ 3.712556] hub 2-0:1.0: 4 ports detected [ 3.713344] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 3.713351] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 3.713943] tegra-xudc-new 700d0000.xudc: device count: 1 [ 3.715613] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 3.715625] tegra-xudc-new 700d0000.xudc: vbus state: 0 [ 3.715657] tegra-xudc-new 700d0000.xudc: entering ELPG [ 3.715922] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 3.716626] mousedev: PS/2 mouse device common for all mice [ 3.716741] usbcore: registered new interface driver xpad [ 3.814483] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 3.814644] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 2 [ 3.814820] usb usb2: usb_suspend_both: status 0 [ 3.847522] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 3.850102] rtc rtc1: alarm rtc device [ 3.850119] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 3.850149] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 3.850790] i2c /dev entries driver [ 3.852725] i2c i2c-6: Added multiplexed i2c bus 7 [ 3.853107] i2c i2c-6: Added multiplexed i2c bus 8 [ 3.853114] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 3.853923] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [ 3.877247] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 3.877336] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 3.877440] imx219 7-0010: board setup failed [ 3.877507] imx219: probe of 7-0010 failed with error -121 [ 3.878079] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [ 3.901343] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 3.901423] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 3.901491] imx219 8-0010: board setup failed [ 3.901544] imx219: probe of 8-0010 failed with error -121 [ 3.903069] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 3.905873] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 3.905880] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 3.906341] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.906384] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 3.906394] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 3.906545] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.906555] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 3.906561] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 3.906712] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.906723] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 3.906729] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 3.906907] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 3.907741] tegra_aotag tegra-aotag: Registering sensor 0 [ 3.907796] tegra_aotag tegra-aotag: Invalid temp readout [ 3.907822] tegra_aotag tegra-aotag: Invalid temp readout [ 3.907840] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 3.907849] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 3.908773] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.908792] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 3.909027] tegra_aotag tegra-aotag: Invalid temp readout [ 3.909058] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 3.909511] parse_throttle_dt_data: Num cap clks = 6 [ 3.909518] parse_throttle_dt_data: clk=cclk_g type=2 [ 3.909534] parse_throttle_dt_data: clk=gpu type=4 [ 3.909562] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 3.909581] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 3.909603] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 3.909606] parse_throttle_dt_data: clk=emc type=3 [ 3.909988] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.910091] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.910223] tegra_throttle_probe: probe successful. #cdevs=4 [ 3.911046] FAN dev name: pwm-fan [ 3.911128] FAN:gpio request success. [ 3.911206] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 3.911516] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 3.911680] pwm_fan_driver pwm-fan: fan tach request irq success [ 3.911690] pwm_fan_driver pwm-fan: tach period: 1000 [ 3.911797] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 3.911802] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 3.911807] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 3.911811] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 3.911815] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 3.911818] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 3.911822] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 3.911826] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 3.911830] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 3.911834] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 3.914783] device-mapper: uevent: version 1.0.3 [ 3.915296] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 3.920984] tegra210-cpufreq cpufreq: probe()...completed [ 3.921767] sdhci: Secure Digital Host Controller Interface driver [ 3.921768] sdhci: Copyright(c) Pierre Ossman [ 3.921770] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.922254] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 3.922652] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 3.922774] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300 [ 3.927350] tegra-se 70012000.se: tegra_se_probe: complete [ 3.927871] hidraw: raw HID events driver (C) Jiri Kosina [ 3.929083] usbcore: registered new interface driver usbhid [ 3.929085] usbhid: USB HID core driver [ 3.931155] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 3.931469] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 3.933333] nvpmodel: initialized successfully [ 3.934311] usbcore: registered new interface driver snd-usb-audio [ 3.934386] No Device Node present for smmu client: snd-soc-dummy !! [ 3.934390] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 3.934408] iommu: Adding device snd-soc-dummy to group 36 [ 3.945372] OPE platform probe [ 3.945462] OPE platform probe successful [ 3.945486] OPE platform probe [ 3.945564] OPE platform probe successful [ 3.951179] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 3.970781] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 3.970899] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 3.971021] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 3.971141] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 3.971260] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 3.971378] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 3.971494] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 3.971612] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 3.971733] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 3.971858] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 3.974517] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 3.984838] u32 classifier [ 3.984840] Actions configured [ 3.984909] Initializing XFRM netlink socket [ 3.985632] NET: Registered protocol family 10 [ 3.986430] NET: Registered protocol family 17 [ 3.986442] NET: Registered protocol family 15 [ 3.986517] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.986570] Bluetooth: RFCOMM socket layer initialized [ 3.986579] Bluetooth: RFCOMM ver 1.11 [ 3.986583] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 3.986587] Bluetooth: HIDP socket layer initialized [ 3.986605] 9pnet: Installing 9P2000 support [ 3.986640] Key type dns_resolver registered [ 3.988396] Registered cp15_barrier emulation handler [ 3.988405] Registered setend emulation handler [ 3.989428] registered taskstats version 1 [ 3.990068] Adding domain ve2-pd to PM domain host1x-pd [ 3.990308] Adding domain ve-pd to PM domain host1x-pd [ 4.046368] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 4.079887] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411 [ 4.079891] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.079894] usb 1-2: Product: 4-Port USB 2.1 Hub [ 4.079896] usb 1-2: Manufacturer: Generic [ 4.080814] hub 1-2:1.0: USB hub found [ 4.081378] hub 1-2:1.0: 4 ports detected [ 4.186748] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.215228] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411 [ 4.215232] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.215235] usb 2-1: Product: 4-Port USB 3.1 Hub [ 4.215237] usb 2-1: Manufacturer: Generic [ 4.218502] hub 2-1:1.0: USB hub found [ 4.219273] hub 2-1:1.0: 4 ports detected [ 4.326409] usb 1-3: new full-speed USB device number 3 using tegra-xusb [ 4.348308] usb 1-3: New USB device found, idVendor=8087, idProduct=0a2b [ 4.348312] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 4.426412] usb 1-2.2: new full-speed USB device number 4 using tegra-xusb [ 4.451260] usb 1-2.2: New USB device found, idVendor=046d, idProduct=c52b [ 4.451264] usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.451266] usb 1-2.2: Product: USB Receiver [ 4.451269] usb 1-2.2: Manufacturer: Logitech [ 4.530715] usb 2-1.3: new SuperSpeed USB device number 3 using tegra-xusb [ 4.551581] usb 2-1.3: New USB device found, idVendor=090c, idProduct=1000 [ 4.551584] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.551587] usb 2-1.3: Product: Flash Drive FIT [ 4.551589] usb 2-1.3: Manufacturer: Samsung [ 4.551591] usb 2-1.3: SerialNumber: 0306321020003681 [ 4.552431] usb-storage 2-1.3:1.0: USB Mass Storage device detected [ 4.552591] scsi host0: usb-storage 2-1.3:1.0 [ 5.138848] tegradc tegradc.0: hdmi: tmds rate:25174K prod-setting:prod_c_hdmi_0m_54m [ 5.146998] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [ 5.154137] tegradc tegradc.0: hdmi: BL set VIC 0 [ 5.158840] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [ 5.178929] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 5.185041] Extcon AUX1(HDMI) enable [ 5.189086] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 5.195514] tegradc tegradc.1: No lt-data, using default setting [ 5.201534] tegradc tegradc.1: No hpd-gpio in DT [ 5.206171] tegradc tegradc.1: DT parsed successfully [ 5.211236] tegradc tegradc.1: Display dc.ffffff800d500000 registered with id=1 [ 5.219336] tegradc tegradc.1: dpd enable lookup fail:-19 [ 5.228825] tegradc tegradc.1: probed [ 5.232222] tegradc tegradc.0: nominal-pclk:25174825 parent:25173906 div:1.0 pclk:25173906 24923052~27440532 [ 5.242583] tegradc tegradc.1: fb registered [ 5.249964] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 5.257097] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 5.258198] isp 54600000.isp: initialized [ 5.259224] isp 54680000.isp: initialized [ 5.269848] last reset is due to power on reset [ 5.269850] KERNEL: PMC reset status reg: 0x0 [ 5.269900] BL: PMC reset status reg: 0x0 [ 5.269902] BL: PMIC poweroff Event Recorder: 0x10 [ 5.271411] clk_cbus_recalc_rate: no gbus parent [ 5.271416] clk_cbus_round_rate: no gbus parent [ 5.271417] clk_cbus_round_rate: no gbus parent [ 5.271424] clk_cbus_recalc_rate: no gbus parent [ 5.271524] clk_cbus_recalc_rate: no gbus parent [ 5.271527] clk_cbus_round_rate: no gbus parent [ 5.271528] clk_cbus_round_rate: no gbus parent [ 5.271532] clk_cbus_recalc_rate: no gbus parent [ 5.271544] tegra_dvfs: GPU-cap: registered [ 5.271604] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 5.271606] tegra dvfs: vdd-core: nominal 1125mV, offset 600000uV, step 12500uV, scaling enabled [ 5.271608] tegra dvfs: vdd-gpu: nominal 1078mV, offset 708000uV, step 10000uV, scaling enabled [ 5.318413] tegra_dvfs: vdd-gpu-vts: registered [ 5.349090] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 5.349713] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 5.350195] input: gpio-keys as /devices/gpio-keys/input/input1 [ 5.389446] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 5.394982] tegradc tegradc.1: blank - powerdown [ 5.399599] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:09:11 UTC (946688951) [ 5.400631] vi 54080000.vi: vi_probe: ++ [ 5.412280] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 5.419509] Extcon DP: HPD disabled [ 5.423007] hpd: hpd_switch 0 [ 5.425974] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 5.432625] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 5.438555] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 5.446902] tegradc tegradc.0: blank - powerdown [ 5.447086] vi 54080000.vi: initialized [ 5.449066] vi 54080000.vi: subdev nvcsi--2 bound [ 5.449171] vi 54080000.vi: subdev nvcsi--1 bound [ 5.450766] Disable partitions left on by BL [ 5.450770] disb [ 5.450817] bwmgr: missing cdev-type property [ 5.450912] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.450918] DRAM derating cdev registered. [ 5.451804] ALSA device list: [ 5.451807] #0: tegra-hda at 0x70038000 irq 83 [ 5.451808] #1: tegra-snd-t210ref-mobile-rt565x [ 5.470697] snd_hda_codec_hdmi hdaudioC0D3: HDMI: Unknown ELD version 0 [ 5.486983] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 5.486985] Extcon AUX1(HDMI) disable [ 5.522470] tegradc tegradc.0: unblank [ 5.558503] tegradc tegradc.0: nominal-pclk:148500000 parent:148500000 div:1.0 pclk:148500000 147015000~161865000 [ 5.558552] tegradc tegradc.0: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_75m_150m [ 5.593144] tegradc tegradc.0: sync windows ret = 247 [ 5.715704] extcon-disp-state extcon:disp-state: cable 51 state 1 [ 5.715706] Extcon HDMI: HPD enabled [ 5.715717] tegradc tegradc.0: hdmi: plugged [ 5.732782] Freeing unused kernel memory: 8576K [ 5.761708] Root device found: PARTUUID=17c0943d-d8d6-47aa-b945-dce49ad99fd4 [ 6.474694] random: crng init done [ 6.625668] scsi 0:0:0:0: Direct-Access Samsung Flash Drive FIT 1100 PQ: 0 ANSI: 6 [ 6.634508] sd 0:0:0:0: [sda] 501253132 512-byte logical blocks: (257 GB/239 GiB) [ 6.642227] sd 0:0:0:0: [sda] Write Protect is off [ 6.647255] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.664070] sda: sda1 [ 6.667492] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 7.123457] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 7.136460] Rootfs mounted over PARTUUID=17c0943d-d8d6-47aa-b945-dce49ad99fd4 [ 7.161123] Switching from initrd to actual rootfs [ 7.323903] systemd[1]: System time before build time, advancing clock. [ 7.367303] ip_tables: (C) 2000-2006 Netfilter Core Team [ 7.387038] cgroup: cgroup2: unknown option "nsdelegate" [ 7.407110] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 7.433646] systemd[1]: Detected architecture arm64. [ 7.471738] systemd[1]: Set hostname to . [ 7.611892] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 7.631239] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 7.772886] systemd[1]: Reached target User and Group Name Lookups. [ 7.785999] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 7.802234] systemd[1]: Created slice System Slice. [ 7.812195] systemd[1]: Listening on udev Kernel Socket. [ 7.822492] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 7.928992] EXT4-fs (sda1): re-mounted. Opts: (null) [ 8.006769] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [ 8.028854] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 8.041032] cpu-throttle-alert cooling device registered. [ 8.049092] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 8.060973] gpu-throttle-alert cooling device registered. [ 8.070673] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 8.084290] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 8.084315] hot-surface-alert cooling device registered. [ 8.191785] systemd-journald[2008]: Received request to flush runtime journal from PID 1 [ 9.651332] using random self ethernet address [ 9.663260] using random host ethernet address [ 10.087367] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-26.ucode failed with error -2 [ 10.098939] iwlwifi 0000:01:00.0: Falling back to user helper [ 10.616234] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-25.ucode failed with error -2 [ 10.627432] iwlwifi 0000:01:00.0: Falling back to user helper [ 10.641231] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-24.ucode failed with error -2 [ 10.641235] iwlwifi 0000:01:00.0: Falling back to user helper [ 10.644595] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-23.ucode failed with error -2 [ 10.644598] iwlwifi 0000:01:00.0: Falling back to user helper [ 11.004259] using random self ethernet address [ 11.010479] using random host ethernet address [ 11.175734] thermal thermal_zone6: failed to read out thermal zone (-5) [ 13.757223] Bridge firewalling registered Ubuntu 18.04.6 LTS Nano ttyS0 Nano login: CTRL-A Z for help | 115200 8N1 | NOR | Minicom 2.7.1 | VT102 | Offline | ttyUSB0