[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (jcl@jcl-ChengMing-3980) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #14 SMP PREEMPT Thu Aug 5 11:11:33 CST 2021 [ 0.000000] Boot CPU: AArch64 Processor [4e0f0040] [ 0.000000] OF: fdt:memory scan node memory, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 2c000000 [ 0.000000] OF: fdt: - ac200000 , 44800000 [ 0.000000] OF: fdt: - 100000000 , 180000000 [ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '') [ 0.000000] bootconsole [tegra_comb_uart0] enabled [ 0.000000] Found tegra_fbmem: 00800000@a06a0000 [ 0.000000] Found lut_mem: 00002008@a069a000 [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb2_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb2_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb3_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb3_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node grid-of-semaphores, compatible id nvidia,gosmem [ 0.000000] cma: Reserved 64 MiB at 0x00000000c2000000 [ 0.000000] On node 0 totalpages: 2031101 [ 0.000000] DMA zone: 7160 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 458237 pages, LIFO batch:31 [ 0.000000] Normal zone: 24576 pages used for memmap [ 0.000000] Normal zone: 1572864 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] pcpu-alloc: s57560 r8192 d32552 u98304 alloc=24*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1999365 [ 0.000000] Kernel command line: console=ttyTCU0,115200 video=tegrafb no_console_suspend=1 earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt rootfs.slot_suffix= tegra_fbmem=0x800000@0xa06a0000 lut_mem=0x2008@0xa069a000 usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=6 boot.slot_suffix= boot.ratchetvalues=0.4.2 vpr_resize sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyTCU0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 163840 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 262144 bytes [ 0.000000] early log buf free: 29188(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Memory: 7182656K/8124404K available (15294K kernel code, 2944K rwdata, 6636K rodata, 8576K init, 611K bss, 188084K reserved, 753664K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff80095f0000 ( 6656 KB) [ 0.000000] .init : 0xffffff80095f0000 - 0xffffff8009e50000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e50000 - 0xffffff800a130008 ( 2945 KB) [ 0.000000] .bss : 0xffffff800a130008 - 0xffffff800a1c8cbc ( 612 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf08000000 ( 128 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc200000000 ( 8192 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 31.25MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xe6a171046, max_idle_ns: 881590405314 ns [ 0.000004] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398046511088ns [ 0.000682] Console: colour dummy device 80x25 [ 0.000693] console [tty0] enabled [ 0.000701] bootconsole [tegra_comb_uart0] disabled [ 0.000714] kmemleak: Kernel memory leak detector disabled [ 0.000733] Calibrating delay loop (skipped), value calculated using timer frequency.. 62.50 BogoMIPS (lpj=125000) [ 0.000749] pid_max: default: 32768 minimum: 301 [ 0.001827] Security Framework initialized [ 0.002389] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.002399] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.004010] ftrace: allocating 47228 entries in 185 pages [ 0.402810] sched-energy: Sched-energy-costs installed from DT [ 0.402829] ASID allocator initialised with 65536 entries [ 0.440253] tegra-id: chipid=21917. [ 0.440264] tegra-id: opt_subrevision=1. [ 0.440291] Tegra Revision: A02p SKU: 0xde CPU Process: 0 SoC Process: 0 [ 0.440311] DTS File Name: ../arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t19x/jakku/kernel-dts/tegra194-p3668-all-p3509-0000.dts [ 0.440321] DTB Build time: Aug 5 2021 11:15:54 [ 0.488505] CPU1: Booted secondary processor [4e0f0040] [ 0.520569] CPU2: Booted secondary processor [4e0f0040] [ 0.552671] CPU3: Booted secondary processor [4e0f0040] [ 0.584945] CPU4: Booted secondary processor [4e0f0040] [ 0.617061] CPU5: Booted secondary processor [4e0f0040] [ 0.617252] Brought up 6 CPUs [ 0.617262] SMP: Total of 6 processors activated. [ 0.617271] CPU features: detected feature: Privileged Access Never [ 0.617278] CPU features: detected feature: LSE atomic instructions [ 0.617284] CPU features: detected feature: User Access Override [ 0.617290] CPU features: detected feature: 32-bit EL0 Support [ 0.618798] CPU: All CPU(s) started at EL2 [ 0.618866] alternatives: patching kernel code [ 0.625167] devtmpfs: initialized [ 0.662976] Initilizing CustomIPI irq domain [ 0.663206] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.663220] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.674868] pinctrl core: initialized pinctrl subsystem [ 0.675104] OS set in device tree is not L4T. [ 0.675351] regulator-dummy: no parameters [ 0.675622] Initializing plugin-manager [ 0.675682] Plugin module not found [ 0.675716] Plugin-manager status disabled [ 0.676773] NET: Registered protocol family 16 [ 0.678311] pstore: using zlib compression [ 0.678342] console [pstore-1] enabled [ 0.678348] pstore: Registered ramoops as persistent store backend [ 0.678355] ramoops: attached 0x200000@0xf0800000, ecc: 0/0 [ 0.695703] cpuidle: using governor menu [ 0.696741] bpmp: waiting for handshake [ 0.696749] bpmp: handshake completed [ 0.696764] bpmp: synchronizing channels [ 0.696773] bpmp: channels synchronized [ 0.696779] bpmp: mail init ok [ 0.699455] t19x-arm-smmu 12000000.iommu: found 3 SMMUs and ISO SMMU id is 2 [ 0.699665] t19x-arm-smmu 12000000.iommu: probing hardware configuration... [ 0.699672] t19x-arm-smmu 12000000.iommu: SMMUv2 with: [ 0.699709] t19x-arm-smmu 12000000.iommu: stage 1 translation [ 0.699715] t19x-arm-smmu 12000000.iommu: stage 2 translation [ 0.699720] t19x-arm-smmu 12000000.iommu: nested translation [ 0.699729] t19x-arm-smmu 12000000.iommu: stream matching with 128 register groups, mask 0x7f80 [ 0.699738] t19x-arm-smmu 12000000.iommu: SMMU address space size (0x800000) differs from mapped region size (0x1000000)! [ 0.699744] t19x-arm-smmu 12000000.iommu: 64 context banks (0 stage-2 only) [ 0.699757] t19x-arm-smmu 12000000.iommu: Stage-1: 39-bit VA -> 48-bit IPA [ 0.699763] t19x-arm-smmu 12000000.iommu: Stage-2: 39-bit IPA -> 48-bit PA [ 0.702771] vdso: 2 pages (1 code @ ffffff8008f77000, 1 data @ ffffff8009e54000) [ 0.702795] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.705298] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.706244] tegra_aon_clk_init: ok [ 0.706253] Registering BPMP clocks... [ 0.706361] tegra_bpmp_clk_init: clock init ok (400 clks) [ 0.706934] Serial: AMBA PL011 UART driver [ 0.707047] tegra_powergate_init: DONE [ 0.707144] DTS File Name: ../arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t19x/jakku/kernel-dts/tegra194-p3668-all-p3509-0000.dts [ 0.707156] DTB Build time: Aug 5 2021 11:15:54 [ 0.709639] Tegra reboot handler registered. [ 0.717394] iommu: Adding device 14160000.pcie to group 0 [ 0.718145] iommu: Adding device 141a0000.pcie to group 1 [ 0.719624] iommu: Adding device 2490000.ether_qos to group 2 [ 0.720149] iommu: Adding device 3100000.serial to group 3 [ 0.720641] iommu: Adding device 3110000.serial to group 4 [ 0.721051] iommu: Adding device 3140000.serial to group 5 [ 0.721632] tegra-pmc c360000.pmc: scratch reg offset dts data not present [ 0.721860] tegra-pmc: get_secure_pmc_setting: done secure_pmc=0 [ 0.721893] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET [ 0.721898] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_L1 [ 0.721904] tegra-pmc: ### PMC reset status reg: 0x2d [ 0.721954] tegra-pmc: PMC Prod config success [ 0.722203] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.722219] tegra-pmc c360000.pmc: IO padctrl driver initialized [ 0.722666] iommu: Adding device 3460000.sdhci to group 6 [ 0.723217] iommu: Adding device 3440000.sdhci to group 7 [ 0.723722] iommu: Adding device 3210000.spi to group 8 [ 0.724156] iommu: Adding device 3230000.spi to group 9 [ 0.724634] iommu: Adding device 3270000.spi to group 10 [ 0.725761] iommu: Adding device 3160000.i2c to group 11 [ 0.726169] iommu: Adding device c240000.i2c to group 12 [ 0.726583] iommu: Adding device 3180000.i2c to group 13 [ 0.726993] iommu: Adding device 3190000.i2c to group 14 [ 0.727794] iommu: Adding device 31b0000.i2c to group 15 [ 0.728248] iommu: Adding device 31c0000.i2c to group 16 [ 0.728687] iommu: Adding device c250000.i2c to group 17 [ 0.729078] iommu: Adding device 31e0000.i2c to group 18 [ 0.729659] iommu: Adding device sound to group 19 [ 0.730184] iommu: Adding device 3510000.hda to group 20 [ 0.730724] iommu: Adding device bc00000.rtcpu to group 21 [ 0.732779] iommu: Adding device 13e10000.host1x to group 22 [ 0.733165] iommu: Adding device 13e10000.host1x:ctx0 to group 23 [ 0.733519] iommu: Adding device 13e10000.host1x:ctx1 to group 24 [ 0.733866] iommu: Adding device 13e10000.host1x:ctx2 to group 25 [ 0.734232] iommu: Adding device 13e10000.host1x:ctx3 to group 26 [ 0.734611] iommu: Adding device 13e10000.host1x:ctx4 to group 27 [ 0.734968] iommu: Adding device 13e10000.host1x:ctx5 to group 28 [ 0.735338] iommu: Adding device 13e10000.host1x:ctx6 to group 29 [ 0.735706] iommu: Adding device 13e10000.host1x:ctx7 to group 30 [ 0.736241] iommu: Adding device 15340000.vic to group 31 [ 0.736633] iommu: Adding device 15380000.nvjpg to group 32 [ 0.736942] iommu: Adding device 15500000.tsec to group 33 [ 0.737212] iommu: Adding device 15100000.tsecb to group 34 [ 0.737477] iommu: Adding device 15480000.nvdec to group 35 [ 0.737775] iommu: Adding device 15140000.nvdec1 to group 36 [ 0.738068] iommu: Adding device 154c0000.nvenc to group 37 [ 0.738352] iommu: Adding device 15a80000.nvenc1 to group 38 [ 0.738776] iommu: Adding device 15880000.nvdla0 to group 39 [ 0.739251] iommu: Adding device 158c0000.nvdla1 to group 40 [ 0.739817] iommu: Adding device 15200000.nvdisplay to group 41 [ 0.740017] platform 15200000.nvdisplay: IOVA linear map 0x00000000a06a0000(800000) [ 0.740034] platform 15200000.nvdisplay: IOVA linear map 0x00000000a069a000(3000) [ 0.744038] platform 15200000.nvdisplay: IOVA linear map 0x00000000c6000000(2a000000) [ 0.744103] t19x-arm-smmu: Adding 15200000.nvdisplay to ISO SMMU client [ 0.744965] iommu: Adding device 15210000.nvdisplay to group 42 [ 0.745027] t19x-arm-smmu: Adding 15210000.nvdisplay to ISO SMMU client [ 0.746991] iommu: Adding device 15c10000.vi to group 43 [ 0.747221] t19x-arm-smmu: Adding 15c10000.vi to ISO SMMU client [ 0.747640] iommu: Adding device 14800000.isp to group 44 [ 0.748716] iommu: Adding device 16000000.pva0 to group 45 [ 0.749258] iommu: Adding device 16800000.pva1 to group 46 [ 0.749716] iommu: Adding device 15810000.se to group 47 [ 0.750178] iommu: Adding device 15820000.se to group 48 [ 0.750528] iommu: Adding device 15830000.se to group 49 [ 0.750813] iommu: Adding device 15840000.se to group 50 [ 0.751075] iommu: Adding device c1a0000.aon to group 51 [ 0.752886] iommu: Adding device d000000.bpmp to group 52 [ 0.753197] bpmp: ping status is 0 [ 0.753329] bpmp d000000.bpmp: firmware tag is e73a758761f0c6d24a1e69a2ac6b5035 [ 0.756484] bpmp d000000.bpmp: probe ok [ 0.758417] tegra-reset 0.bpmp_reset: registered 190 resets. [ 0.758894] iommu: Adding device smmu_test to group 53 [ 0.760033] mc: mapped MMIO address: 0xffffff800a590000 -> 0x2c10000 [ 0.760062] mc: mapped MMIO address: 0xffffff800a5b0000 -> 0x2c20000 [ 0.760085] mc: mapped MMIO address: 0xffffff800a5d0000 -> 0x2c30000 [ 0.760137] mc: mapped MMIO address: 0xffffff800a7b0000 -> 0x2c40000 [ 0.760160] mc: mapped MMIO address: 0xffffff800a7d0000 -> 0x2c50000 [ 0.760186] mc: mapped MMIO address: 0xffffff800b010000 -> 0x2b80000 [ 0.760207] mc: mapped MMIO address: 0xffffff800b030000 -> 0x2b90000 [ 0.760227] mc: mapped MMIO address: 0xffffff800b050000 -> 0x2ba0000 [ 0.760247] mc: mapped MMIO address: 0xffffff800b070000 -> 0x2bb0000 [ 0.760267] mc: mapped MMIO address: 0xffffff800b090000 -> 0x1700000 [ 0.760286] mc: mapped MMIO address: 0xffffff800b0b0000 -> 0x1710000 [ 0.760306] mc: mapped MMIO address: 0xffffff800b0d0000 -> 0x1720000 [ 0.760326] mc: mapped MMIO address: 0xffffff800b0f0000 -> 0x1730000 [ 0.760346] mc: mapped MMIO address: 0xffffff800b110000 -> 0x1740000 [ 0.760366] mc: mapped MMIO address: 0xffffff800b130000 -> 0x1750000 [ 0.760386] mc: mapped MMIO address: 0xffffff800b150000 -> 0x1760000 [ 0.760425] mc: mapped MMIO address: 0xffffff800b170000 -> 0x1770000 [ 0.760508] mc-err: mcerr ops are set to t19x [ 0.766886] iommu: Adding device 2600000.dma to group 54 [ 0.773101] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 224 lines on the chip [ 0.774343] GPIO line 339 (wifi-enable) hogged as output/high [ 0.774394] GPIO line 412 (camera-control-output-low) hogged as output/low [ 0.774453] GPIO line 413 (camera-control-output-low) hogged as output/low [ 0.774783] gpiochip_setup_dev: registered GPIOs 288 to 511 on device: gpiochip0 (tegra-gpio) [ 0.781772] IndicatorLightPin init sucess [ 0.783224] gpio gpiochip1: gpio-line-names specifies 21 line names but there are 40 lines on the chip [ 0.783313] GPIO line 253 (pex-refclk-sel-low) hogged as output/low [ 0.783352] GPIO line 266 (w-disable1) hogged as output/high [ 0.783385] GPIO line 264 (w-disable2) hogged as output/high [ 0.783441] GPIO line 265 (suspend-led-gpio) hogged as output/high [ 0.783758] gpiochip_setup_dev: registered GPIOs 248 to 287 on device: gpiochip1 (tegra-gpio-aon) [ 0.785008] [tegra_gpio_probe:1884] gpio_request IndicatorLightPin fail ret:-16 [ 0.786138] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CNTRL_83 = 0x10a [ 0.786152] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CTRL_0 = 3 [ 0.786185] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CNTRL_24(PMU_INT) = 256 [ 0.787354] iommu: Adding device 3550000.xudc to group 55 [ 0.788132] iommu: Adding device 3610000.xhci to group 56 [ 0.790450] arm64_ras arm64_ras: probed [ 0.790898] ras_fhi_enable: FHI 470 enabled on CPU0 [ 0.790942] ras_fhi_enable: FHI 471 enabled on CPU1 [ 0.791020] ras_fhi_enable: FHI 472 enabled on CPU2 [ 0.791130] ras_fhi_enable: FHI 473 enabled on CPU3 [ 0.791219] ras_fhi_enable: FHI 474 enabled on CPU4 [ 0.791296] ras_fhi_enable: FHI 475 enabled on CPU5 [ 0.791486] carmel_ras_enable: RAS enabled on cpu0 [ 0.791665] carmel_ras_enable: RAS enabled on cpu1 [ 0.791864] carmel_ras_enable: RAS enabled on cpu2 [ 0.792070] carmel_ras_enable: RAS enabled on cpu3 [ 0.792266] carmel_ras_enable: RAS enabled on cpu4 [ 0.792488] carmel_ras_enable: RAS enabled on cpu5 [ 0.792566] carmel_ras carmel_ras: probed [ 0.793974] tegra-cbb 2300000.cbb-noc: noc_secure_irq = 479, noc_nonsecure_irq = 478> [ 0.794684] tegra-cbb c600000.aon-noc: noc_secure_irq = 481, noc_nonsecure_irq = 480> [ 0.795638] tegra-cbb d600000.bpmp-noc: noc_secure_irq = 483, noc_nonsecure_irq = 482> [ 0.796537] tegra-cbb be00000.rce-noc: noc_secure_irq = 485, noc_nonsecure_irq = 484> [ 0.797402] tegra-cbb b600000.sce-noc: noc_secure_irq = 487, noc_nonsecure_irq = 486> [ 0.797806] tegra-cbb 14040000.cv-noc: defer probe as CV-NOC not probed yet [ 0.799205] vdd-ac-bat: 5000 mV [ 0.799662] vdd-sdmmc3-sw: 3300 mV [ 0.799999] vdd-3v3-cvb: 3300 mV [ 0.800317] vdd-1v8-cvb: 1800 mV [ 0.800752] vdd-epb-1v0: supplied by vdd-3v3-cvb [ 0.800808] vdd-epb-1v0: 1000 mV [ 0.801213] avdd-cam-2v8: 2800 mV [ 0.801553] vdd-fan: 5000 mV [ 0.801869] vdd-hdmi-5v0: 5000 mV [ 0.802181] vdd_sys_en: 1200 mV [ 0.833629] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.838748] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.839050] SCSI subsystem initialized [ 0.839294] libata version 3.00 loaded. [ 0.839567] usbcore: registered new interface driver usbfs [ 0.839638] usbcore: registered new interface driver hub [ 0.839755] usbcore: registered new device driver usb [ 0.850975] tegra-i2c 31e0000.i2c: could not find pctldev for node /host1x/dpaux@155F0000/pinmux@0, deferring probe [ 0.853985] max77620 4-003c: PMIC Version OTP:0x51 and ES:0x1 [ 0.861087] vdd-1v0: at 1000 mV [ 0.865129] vdd-1v8-hs: at 1800 mV [ 0.869121] vdd-1v8-ls: at 1800 mV [ 0.873124] vdd-1v8-ao: at 1800 mV [ 0.877150] vddio-ddr-1v1: at 1100 mV [ 0.880930] vdd-rtc: at 800 mV [ 0.881879] spmic-ldo1: at 2375 mV [ 0.889003] vdd-ao-3v3: at 3300 mV [ 0.897034] vddio-emmc-3v3: at 3300 mV [ 0.898202] spmic-ldo4: at 1587 mV [ 0.905082] vdd-usb-3v3: at 3300 mV [ 0.913110] vddio-sdmmc1-3v3: at 3300 mV [ 0.917137] vdd-csi-1v2: at 1200 mV [ 0.918179] spmic-ldo8: at 1800 mV [ 0.922349] GPIO line 246 (gpio_default) hogged as output/high [ 0.923340] GPIO line 247 (gpio_default) hogged as output/high [ 0.923638] gpiochip_setup_dev: registered GPIOs 240 to 247 on device: gpiochip2 (max77620-gpio) [ 0.923971] max77620 4-003c: max77620 probe successful [ 0.924632] media: Linux media interface: v0.10 [ 0.924679] Linux video capture interface: v2.00 [ 0.926179] pps_core: LinuxPPS API ver. 1 registered [ 0.926192] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.926213] PTP clock support registered [ 0.926524] tegra_wdt_t18x 30c0000.watchdog: Expiry count is deprecated [ 0.926769] tegra_wdt_t18x 30c0000.watchdog: Tegra WDT init timeout = 120 sec [ 0.926795] tegra_wdt_t18x 30c0000.watchdog: Registered successfully [ 0.929573] trusty trusty: trusty version: Built: 08:40:57 Feb 19 2021 [ 0.929633] trusty trusty: selected api version: 3 (requested 3) [ 0.930933] Advanced Linux Sound Architecture Driver Initialized. [ 0.931435] Bluetooth: Core ver 2.22 [ 0.931568] NET: Registered protocol family 31 [ 0.931597] Bluetooth: HCI device and connection manager initialized [ 0.931612] Bluetooth: HCI socket layer initialized [ 0.931621] Bluetooth: L2CAP socket layer initialized [ 0.931658] Bluetooth: SCO socket layer initialized [ 0.934638] camchar: rtcpu character device driver loaded [ 0.935191] gpio tegra-gpio wake61 for gpio=201(Z:1) [ 0.935286] extcon-gpio-states external-connection:extcon@1: Cable state:0, cable id:0 [ 0.937271] clocksource: Switched to clocksource arch_sys_counter [ 0.982761] VFS: Disk quotas dquot_6.6.0 [ 0.982862] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.983231] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.984763] tegra-carveouts tegra-carveouts: assigned reserved memory node grid-of-semaphores [ 0.984829] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000c6000000, size=0x2a000000 [ 0.985184] cma: enabled page replacement for spfn=c6000, epfn=f0000 [ 0.985196] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.985216] nvmap: nvmap_select_cache_ops() nvmap cache ops set to scf [ 0.985229] nvmap_page_pool_init: Total RAM pages: 1984080 [ 0.985240] nvmap_page_pool_init: nvmap page pool size: 248010 pages (968 MB) [ 0.985390] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.985962] misc nvmap: created heap vpr base 0x00000000c6000000 size (688128KiB) [ 0.987428] tegra-gpcdma 2600000.dma: GPC DMA driver register 31 channels [ 1.000670] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type CPU-therm [ 1.000903] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type GPU-therm [ 1.001151] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type AUX-therm [ 1.001347] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type AO-therm [ 1.001540] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 1.002739] la/ptsa driver initialized. [ 1.003116] NET: Registered protocol family 2 [ 1.003938] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 1.004283] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 1.004975] TCP: Hash tables configured (established 65536 bind 65536) [ 1.005052] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 1.005194] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 1.005582] NET: Registered protocol family 1 [ 1.006242] RPC: Registered named UNIX socket transport module. [ 1.006253] RPC: Registered udp transport module. [ 1.006261] RPC: Registered tcp transport module. [ 1.006269] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.006283] PCI: CLS 0 bytes, default 64 [ 1.006504] Trying to unpack rootfs image as initramfs... [ 1.238620] Freeing initrd memory: 7064K [ 1.260083] host1x 13e10000.host1x: initialized [ 1.262203] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.267402] audit: initializing netlink subsys (disabled) [ 1.267455] audit: type=2000 audit(0.888:1): initialized [ 1.268164] workingset: timestamp_bits=46 max_order=21 bucket_order=0 [ 1.277884] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.279146] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.279841] 9p: Installing v9fs 9p2000 file system support [ 1.285673] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 1.285958] io scheduler noop registered [ 1.286223] io scheduler cfq registered (default) [ 1.289951] gic 2a41000.agic-controller: GIC IRQ controller registered [ 1.291179] random: fast init done [ 1.324677] iommu: Adding device 2993000.adsp to group 57 [ 1.412986] iommu: Adding device aconnect@2a41000:adsp_audio to group 58 [ 1.413179] tegra-aconnect aconnect@2a41000: Tegra ACONNECT bus registered [ 1.425416] tegra-pwm 3280000.pwm: PWM clk can sleep in ops [ 1.425822] tegra-pwm c340000.pwm: PWM clk can sleep in ops [ 1.426339] tegra-pwm 32c0000.pwm: PWM clk can sleep in ops [ 1.426700] tegra-pwm 32d0000.pwm: PWM clk can sleep in ops [ 1.427139] tegra-pwm 32f0000.pwm: PWM clk can sleep in ops [ 1.429580] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.429761] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 1.432293] tsec 15500000.tsec: initialized [ 1.433821] tsec 15100000.tsecb: initialized [ 1.437173] nvdec 15480000.nvdec: initialized [ 1.439466] nvdec 15140000.nvdec1: initialized [ 1.444664] falcon 15340000.vic: initialized [ 1.446369] falcon 15380000.nvjpg: initialized [ 1.448056] falcon 154c0000.nvenc: initialized [ 1.449766] falcon 15a80000.nvenc1: initialized [ 1.453117] iommu_context_dev 13e10000.host1x:ctx0: initialized (streamid=56) [ 1.454447] iommu_context_dev 13e10000.host1x:ctx1: initialized (streamid=57) [ 1.455719] iommu_context_dev 13e10000.host1x:ctx2: initialized (streamid=58) [ 1.457119] iommu_context_dev 13e10000.host1x:ctx3: initialized (streamid=59) [ 1.458397] iommu_context_dev 13e10000.host1x:ctx4: initialized (streamid=60) [ 1.459688] iommu_context_dev 13e10000.host1x:ctx5: initialized (streamid=61) [ 1.460985] iommu_context_dev 13e10000.host1x:ctx6: initialized (streamid=62) [ 1.462219] iommu_context_dev 13e10000.host1x:ctx7: initialized (streamid=63) [ 1.465670] t194-nvcsi 15a00000.nvcsi: initialized [ 1.470735] scare-pigeon 13e10000.host1x:vi-thi@15f00000: initialized [ 1.471145] scare-pigeon 14b00000.isp-thi: initialized [ 1.476763] pva 16000000.pva0: initialized [ 1.482175] pva 16800000.pva1: initialized [ 1.487085] nvdla 15880000.nvdla0: initialized [ 1.491592] nvdla 158c0000.nvdla1: initialized [ 1.492866] tegradccommon 15200000.dc_common: host1x channel mapped [ 1.492878] tegradccommon 15200000.dc_common: dc_common syncpt # 1 allocated [ 1.492936] tegradccommon 15200000.dc_common: dma mapping done [ 1.493869] tegradc 15200000.nvdisplay: disp0 connected to head0->/host1x/sor1 [ 1.493908] generic_infoframe_type: 0x87 [ 1.493981] tegradc 15200000.nvdisplay: DT parsed successfully [ 1.494012] tegradc 15200000.nvdisplay: Display dc.ffffff800bd10000 registered with id=0 [ 1.497806] tegra_nvdisp_bandwidth_register_max_config: max config iso bw = 7088400 KB/s [ 1.497818] tegra_nvdisp_bandwidth_register_max_config: max config EMC floor = 800000000 Hz [ 1.497828] tegra_nvdisp_bandwidth_register_max_config: max config hubclk = 300000000 Hz [ 1.498021] tegradc 15200000.nvdisplay: vblank syncpt # 8 for dc 0 [ 1.498030] tegradc 15200000.nvdisplay: vpulse3 syncpt # 9 for dc 0 [ 1.498967] tegradc 15200000.nvdisplay: Bootloader disp_param detected. Detected mode: 1920x1080 (on 0x0mm) pclk=148350937 [ 1.501335] tegradc 15200000.nvdisplay: hdmi: invalid prod list prod_list_hdmi_board [ 1.501343] tegradc 15200000.nvdisplay: hdmi: tegra_hdmi_tmds_range_read(bd) failed [ 1.504743] tegradc 15200000.nvdisplay: probed [ 1.541302] Console: switching to colour frame buffer device 240x67 [ 1.541440] tegradc 15200000.nvdisplay: fb registered [ 1.541807] gpio tegra-gpio wake63 for gpio=97(M:1) [ 1.542512] tegra_nvdisp_handle_pd_enable: Unpowergated Head0 pd [ 1.542610] tegra_nvdisp_handle_pd_enable: Unpowergated Head1 pd [ 1.545040] Parent Clock set for DC plld2 [ 1.604954] tegradc 15200000.nvdisplay: hdmi: tmds rate:148351K prod-setting:prod_c_hdmi_111m_223m [ 1.605603] tegradc 15200000.nvdisplay: hdmi: get RGB quant from REG programmed by BL. [ 1.605616] tegradc 15200000.nvdisplay: hdmi: get YCC quant from REG programmed by BL. [ 1.631269] extcon-disp-state external-connection:disp-state: cable 47 state 1 [ 1.631300] Extcon AUX1(HDMI) enable [ 1.631740] tegradc 15210000.nvdisplay: disp1 connected to head1->/host1x/sor [ 1.631772] tegradc 15210000.nvdisplay: parse_dp_settings: No dp-lt-settings node [ 1.631846] tegradc 15210000.nvdisplay: DT parsed successfully [ 1.631894] tegradc 15210000.nvdisplay: Display dc.ffffff800be10000 registered with id=1 [ 1.632146] tegradc 15210000.nvdisplay: vblank syncpt # 11 for dc 1 [ 1.632155] tegradc 15210000.nvdisplay: vpulse3 syncpt # 12 for dc 1 [ 1.640891] tegradc 15210000.nvdisplay: probed [ 1.641289] tegradc 15210000.nvdisplay: fb registered [ 1.644572] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 1.644588] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 1.644604] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 1.644621] tegradc 15210000.nvdisplay: blank - powerdown [ 1.644636] extcon-disp-state external-connection:disp-state: cable 44 state 0 already set. [ 1.644642] Extcon DP: HPD disabled [ 1.644651] hpd: hpd_switch 0 [ 1.644679] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 1.644697] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 1.644706] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 1.644959] tegra_cec 3960000.tegra_cec: dt=1 start=0x03960000 end=0x03960FFF irq=78 [ 1.644969] tegra_cec 3960000.tegra_cec: Unpowergate DISP: 0. [ 1.645208] tegra_cec 3960000.tegra_cec: Enable clock result: 0. [ 1.645310] tegra_cec 3960000.tegra_cec: tegra_cec_init started [ 1.645443] tegra_cec 3960000.tegra_cec: cec_add_sysfs ret=0 [ 1.645449] tegra_cec 3960000.tegra_cec: probed [ 1.654284] tegra-adma 2930000.adma: Tegra210 ADMA driver registered 32 channels [ 1.655020] tegra-fuse-burn 3820000.efuse:efuse-burn: shutdown limit check disabled [ 1.655028] tegra-fuse-burn 3820000.efuse:efuse-burn: Fuse burn driver initialized [ 1.655345] kfuse 3830000.kfuse: initialized [ 1.660267] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.662541] 3100000.serial: ttyTHS0 at MMIO 0x3100000 (irq = 47, base_baud = 0) is a TEGRA_UART [ 1.663498] 3110000.serial: ttyTHS1 at MMIO 0x3110000 (irq = 48, base_baud = 0) is a TEGRA_UART [ 1.664120] 3140000.serial: ttyTHS4 at MMIO 0x3140000 (irq = 49, base_baud = 0) is a TEGRA_UART [ 1.665305] console [ttyTCU0] enabled [ 1.665629] [drm] Initialized [ 1.676184] brd: module loaded [ 1.681042] loop: module loaded [ 1.681172] tegra_profiler: version: 1.143, samples/io: 48/28 [ 1.681305] tegra_profiler: auth: init [ 1.681899] THERMAL EST: found 3 subdevs [ 1.681906] THERMAL EST num_resources: 0 [ 1.681911] [THERMAL EST subdev 0] [ 1.681917] [THERMAL EST subdev 1] [ 1.681923] [THERMAL EST subdev 2] [ 1.681932] THERMAL EST: Found 2 profiles, default profile is quiet [ 1.682208] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 1.682214] THERMAL EST: thz register success. [ 1.682462] THERMAL EST: end of probe, return err: 0 [ 1.683019] sd: No Scsi addr parsed to reserve index [ 1.683046] hisi_sas: driver version v1.6 [ 1.692649] qspi_mtd spi6.0: s25fs256s SSG 8 0 1000 2000000 [ 1.692659] qspi_mtd spi6.0: s25fs256s (32768 Kbytes) [ 1.692669] qspi_mtd spi6.0: mtd .name = spi6.0, .size = 0x2000000 (32MiB) .erasesize = 0x00010000 (64KiB) .numeraseregions = 0 [ 1.692901] 1 ofpart partitions found on MTD device spi6.0 [ 1.692906] Creating 1 MTD partitions on "spi6.0": [ 1.692915] 0x000000000000-0x000002000000 : "Whole_flash0" [ 1.696341] libphy: Fixed MDIO Bus: probed [ 1.696930] tun: Universal TUN/TAP device driver, 1.6 [ 1.696935] tun: (C) 1999-2004 Max Krasnyansky [ 1.697789] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.697794] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.697833] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.697837] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.697871] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.697875] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.697911] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 1.697916] Copyright(c) 1999 - 2017 Intel Corporation. [ 1.763670] tegradc 15200000.nvdisplay: blank - powerdown [ 1.805313] extcon-disp-state external-connection:disp-state: cable 47 state 0 [ 1.805317] Extcon AUX1(HDMI) disable [ 1.831687] tegra_nvdisp_handle_pd_disable: Powergated Head1 pd [ 1.832870] tegra_nvdisp_handle_pd_disable: Powergated Head0 pd [ 1.853113] tegradc 15200000.nvdisplay: unblank [ 1.854943] tegra_nvdisp_handle_pd_enable: Unpowergated Head0 pd [ 1.855285] tegra_nvdisp_handle_pd_enable: Unpowergated Head1 pd [ 1.863923] Parent Clock set for DC plld2 [ 1.868779] tegradc 15200000.nvdisplay: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_111m_223m [ 1.870206] tegradc 15200000.nvdisplay: hdmi: get YCC quant from EDID. [ 1.904974] extcon-disp-state external-connection:disp-state: cable 47 state 1 [ 1.904978] Extcon AUX1(HDMI) enable [ 1.920427] tegradc 15200000.nvdisplay: sync windows ret = 246 [ 1.947438] eqos 2490000.ether_qos: failed to read eqos_auto_cal_config_0_reg [ 1.948087] eqos 2490000.ether_qos: Setting local MAC: 48 b0 2d 38 41 67 [ 1.948222] libphy: dwc_phy: probed [ 1.950693] PPP generic driver version 2.4.2 [ 1.951151] PPP BSD Compression module registered [ 1.951156] PPP Deflate Compression module registered [ 1.951202] PPP MPPE Compression module registered [ 1.951207] NET: Registered protocol family 24 [ 1.951251] usbcore: registered new interface driver r8152 [ 1.951280] usbcore: registered new interface driver asix [ 1.951310] usbcore: registered new interface driver ax88179_178a [ 1.951358] usbcore: registered new interface driver cdc_ether [ 1.951382] usbcore: registered new interface driver net1080 [ 1.951408] usbcore: registered new interface driver cdc_subset [ 1.951432] usbcore: registered new interface driver zaurus [ 1.951465] usbcore: registered new interface driver cdc_ncm [ 1.952009] VFIO - User Level meta-driver version: 0.3 [ 1.953370] extcon-disp-state external-connection:disp-state: cable 51 state 1 [ 1.953376] Extcon HDMI: HPD enabled [ 1.953400] tegradc 15200000.nvdisplay: hdmi: plugged [ 1.953440] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.953462] ehci-pci: EHCI PCI platform driver [ 1.953495] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.953504] ohci-pci: OHCI PCI platform driver [ 1.953534] ohci-platform: OHCI generic platform driver [ 1.959000] tegra-xusb 3610000.xhci: USB2 port 0 has OTG_CAP [ 1.960938] tegra-xusb 3610000.xhci: extcon 0: ffffffc1f5a8a800 id [ 1.961567] usbcore: registered new interface driver uas [ 1.961639] usbcore: registered new interface driver usb-storage [ 1.961848] usbcore: registered new interface driver usbserial [ 1.961968] usbcore: registered new interface driver option [ 1.962044] usbserial: USB Serial support registered for GSM modem (1-port) [ 1.963348] tegra-xusb 3610000.xhci: Firmware timestamp: 2019-07-24 05:47:34 UTC, Version: 60.06 release [ 1.963380] tegra-xusb 3610000.xhci: xHCI Host Controller [ 1.963400] tegra-xusb 3610000.xhci: new USB bus registered, assigned bus number 1 [ 1.964141] tegra-xusb 3610000.xhci: hcc params 0x0184ff25 hci version 0x110 quirks 0x00050810 [ 1.964179] tegra-xusb 3610000.xhci: irq 465, io mem 0x03610000 [ 1.964456] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.964463] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.964470] usb usb1: Product: xHCI Host Controller [ 1.964476] usb usb1: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 1.964507] usb usb1: SerialNumber: 3610000.xhci [ 1.964948] hub 1-0:1.0: USB hub found [ 1.964993] hub 1-0:1.0: 4 ports detected [ 1.965592] tegra-xusb 3610000.xhci: xHCI Host Controller [ 1.965606] tegra-xusb 3610000.xhci: new USB bus registered, assigned bus number 2 [ 1.965615] tegra-xusb 3610000.xhci: Host supports USB 3.1 Enhanced SuperSpeed [ 1.965840] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.965848] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.965855] usb usb2: Product: xHCI Host Controller [ 1.965861] usb usb2: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 1.965867] usb usb2: SerialNumber: 3610000.xhci [ 1.966268] hub 2-0:1.0: USB hub found [ 1.966307] hub 2-0:1.0: 4 ports detected [ 1.966789] tegra-xudc-new 3550000.xudc: PMQOS CPU boost enabled [ 1.966880] tegra-xudc-new 3550000.xudc: device count: 1 [ 1.966997] Wake76 for irq=199 [ 1.967004] Wake77 for irq=199 [ 1.967008] Wake78 for irq=199 [ 1.967012] Wake79 for irq=199 [ 1.967016] Wake80 for irq=199 [ 1.967020] Wake81 for irq=199 [ 1.967024] Wake82 for irq=199 [ 1.967059] tegra-xusb 3610000.xhci: Upgrade port 0 to USB3.0 [ 1.967067] tegra-xusb 3610000.xhci: Upgrade port 1 to USB3.0 [ 1.967764] tegra-xudc-new 3550000.xudc: vbus state: 0 [ 1.967775] tegra-xudc-new 3550000.xudc: Initialize boost_cpufreq work [ 1.968040] tegra-xudc-new 3550000.xudc: entering ELPG [ 1.968575] tegra-xudc-new 3550000.xudc: entering ELPG done [ 1.968739] mousedev: PS/2 mouse device common for all mice [ 1.968808] usbcore: registered new interface driver xpad [ 2.069037] usb usb2: usb_suspend_both: status 0 [ 2.099484] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 2.101007] Wake73 for irq=42 [ 2.102322] rtc rtc1: alarm rtc device [ 2.102340] tegra_rtc c2a0000.rtc: rtc core: registered c2a0000.rtc as rtc1 [ 2.102371] tegra_rtc c2a0000.rtc: Tegra internal Real Time Clock [ 2.102501] i2c /dev entries driver [ 2.104468] i2c i2c-2: Added multiplexed i2c bus 9 [ 2.104848] i2c i2c-2: Added multiplexed i2c bus 10 [ 2.104857] i2c-mux-gpio cam_i2cmux: 2 port mux on 3180000.i2c adapter [ 2.105395] imx219 9-0010: tegracam sensor driver:imx219_v2.0.6 [ 2.128942] tegra-i2c 3180000.i2c: no acknowledge from address 0x10 [ 2.128999] imx219 9-0010: imx219_board_setup: error during i2c read probe (-121) [ 2.129306] imx219 9-0010: board setup failed [ 2.129492] imx219: probe of 9-0010 failed with error -121 [ 2.129915] imx219 10-0010: tegracam sensor driver:imx219_v2.0.6 [ 2.153185] tegra-i2c 3180000.i2c: no acknowledge from address 0x10 [ 2.153233] imx219 10-0010: imx219_board_setup: error during i2c read probe (-121) [ 2.153551] imx219 10-0010: board setup failed [ 2.153776] imx219: probe of 10-0010 failed with error -121 [ 2.154954] max77620-power max20024-power: Event recorder REG_NVERC : 0x0 [ 2.155500] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 2.161572] tegra-thermal-throttle bthrot_cdev: cpufreq policy is not ready defer [ 2.161913] FAN dev name: pwm-fan [ 2.161966] FAN:gpio request success. [ 2.161977] FAN: can't find tach_gpio [ 2.161987] pwm_fan_driver pwm-fan: Found 2 profiles, default profile is quiet [ 2.162035] pwm_fan_driver pwm-fan: cap state:4, cap pwm:255 [ 2.162241] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 2.162250] pwm_fan_driver pwm-fan: tach period: 1000 [ 2.162788] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 2.162796] pwm_fan_driver pwm-fan: index 1: pwm=130, rpm=1000, rru=2, rrd=2, state:2 [ 2.162803] pwm_fan_driver pwm-fan: index 2: pwm=160, rpm=2000, rru=1, rrd=1, state:2 [ 2.162809] pwm_fan_driver pwm-fan: index 3: pwm=200, rpm=3000, rru=1, rrd=1, state:2 [ 2.162815] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 2.162822] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 2.162827] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 2.162834] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 2.162841] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 2.162848] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 2.163514] tegra-oc-event d280000.soctherm-oc-event: OC driver initialized [ 2.164333] device-mapper: uevent: version 1.0.3 [ 2.164760] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 2.167989] tegra194_cpufreq_probe: platform driver Initialization: pass [ 2.169211] cpuidle: Initializing cpuidle driver [ 2.169974] sdhci: Secure Digital Host Controller Interface driver [ 2.169978] sdhci: Copyright(c) Pierre Ossman [ 2.169982] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.171055] sdhci-tegra 3460000.sdhci: Client registration for eMC Successful [ 2.172949] CMDQ: cmdq_platfm_init successful [ 2.173366] sdhci-tegra 3440000.sdhci: Got CD GPIO [ 2.175524] sdhci-tegra 3440000.sdhci: Client registration for eMC Successful [ 2.177337] sdhci-tegra 3440000.sdhci: wakeup init done, cdirq 322 [ 2.181657] tegra-se-elp 3ad0000.se_elp: tegra_se_elp_probe: complete [ 2.182687] tegra-se-nvhost 15810000.se: initialized [ 2.184267] tegra-se-nvhost 15810000.se: tegra_se_probe: complete [ 2.185035] tegra-se-nvhost 15820000.se: initialized [ 2.186104] tegra-se-nvhost 15820000.se: tegra_se_probe: complete [ 2.186746] tegra-se-nvhost 15830000.se: initialized [ 2.187520] tegra-se-nvhost 15830000.se: tegra_se_probe: complete [ 2.188231] tegra-se-nvhost 15840000.se: initialized [ 2.189289] tegra-se-nvhost 15840000.se: tegra_se_probe: complete [ 2.189528] hidraw: raw HID events driver (C) Jiri Kosina [ 2.190733] usbcore: registered new interface driver usbhid [ 2.190736] usbhid: USB HID core driver [ 2.195775] tegra186-cam-rtcpu bc00000.rtcpu: deferring, 14800000.isp is not probed [ 2.196936] tegra_aon c1a0000.aon: tegra aon driver probe OK [ 2.197316] tegra186-aondbg aondbg: aondbg driver probe() OK [ 2.197911] denver_knobs_init:MTS_VERSION:51035886 [ 2.198064] tegra19x_actmon d230000.actmon: in actmon_register()... [ 2.198703] tegra19x_actmon d230000.actmon: initialization Completed for the device mc_all [ 2.199088] t19x_cache tegra-cache: probed [ 2.201833] misc nvmap: cvsram :dma coherent mem declare 0x0000000050000000,4194304 [ 2.201842] misc nvmap: created heap cvsram base 0x0000000050000000 size (4096KiB) [ 2.202327] carmel-pmu-drv carmel-pmu: Registered Carmel PMU [ 2.202705] PLL_AON clock registered [ 2.203985] Clocks initialized successfully [ 2.205426] nvpmodel: initialized successfully [ 2.206419] trusty-virtio trusty:virtio: initializing [ 2.206617] trusty_ipc virtio0: vring0: va(pa) ffffffc1e26ac000(0) qsz 32 notifyid 1 [ 2.206627] trusty_ipc virtio0: vring1: va(pa) ffffffc1e26ae000(0) qsz 32 notifyid 2 [ 2.206796] trusty-virtio trusty:virtio: initializing done [ 2.207096] trusty_ipc virtio0: is online [ 2.207588] tegra-hda 3510000.hda: Override SDO lines to 4 [ 2.208096] usbcore: registered new interface driver snd-usb-audio [ 2.216451] mmc0: SDHCI controller on 3460000.sdhci [3460000.sdhci] using ADMA 64-bit with 64 bit addr [ 2.226746] input: tegra-hda-xnx HDMI/DP,pcm=3 as /devices/3510000.hda/sound/card0/input0 [ 2.228034] input: tegra-hda-xnx HDMI/DP,pcm=7 as /devices/3510000.hda/sound/card0/input1 [ 2.228214] input: tegra-hda-xnx HDMI/DP,pcm=8 as /devices/3510000.hda/sound/card0/input2 [ 2.228498] input: tegra-hda-xnx HDMI/DP,pcm=9 as /devices/3510000.hda/sound/card0/input3 [ 2.228537] gpio tegra-gpio wake51 for gpio=130(Q:2) [ 2.228595] mmc1: SDHCI controller on 3440000.sdhci [3440000.sdhci] using ADMA 64-bit with 64 bit addr [ 2.262399] mmc0: mmc_decode_ext_csd: CMDQ supported: depth: 31, cmdq_support: 1 [ 2.275526] mmc0: periodic cache flush enabled [ 2.275570] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 2.276129] mmcblk0: mmc0:0001 DG4016 14.7 GiB [ 2.276417] mmcblk0boot0: mmc0:0001 DG4016 partition 1 4.00 MiB [ 2.276616] mmcblk0boot1: mmc0:0001 DG4016 partition 2 4.00 MiB [ 2.276822] mmcblk0rpmb: mmc0:0001 DG4016 partition 3 4.00 MiB [ 2.279756] OPE platform probe [ 2.279839] OPE platform probe successful [ 2.283501] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 [ 2.296426] usb 1-3: new high-speed USB device number 2 using tegra-xusb [ 2.316760] usb 1-3: New USB device found, idVendor=1a40, idProduct=0101 [ 2.316766] usb 1-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.316770] usb 1-3: Product: USB 2.0 Hub [ 2.317493] hub 1-3:1.0: USB hub found [ 2.317554] hub 1-3:1.0: 4 ports detected [ 2.354689] tegra-asoc: sound: ADMAIF1 <-2789-1-test> ADMAIF1 mapping ok [ 2.354833] tegra-asoc: sound: ADMAIF2 <-2789-1-test> ADMAIF2 mapping ok [ 2.354967] tegra-asoc: sound: ADMAIF3 <-2789-1-test> ADMAIF3 mapping ok [ 2.355094] tegra-asoc: sound: ADMAIF4 <-2789-1-test> ADMAIF4 mapping ok [ 2.355221] tegra-asoc: sound: ADMAIF5 <-2789-1-test> ADMAIF5 mapping ok [ 2.355337] tegra-asoc: sound: ADMAIF6 <-2789-1-test> ADMAIF6 mapping ok [ 2.355448] tegra-asoc: sound: ADMAIF7 <-2789-1-test> ADMAIF7 mapping ok [ 2.355557] tegra-asoc: sound: ADMAIF8 <-2789-1-test> ADMAIF8 mapping ok [ 2.355686] tegra-asoc: sound: ADMAIF9 <-2789-1-test> ADMAIF9 mapping ok [ 2.355793] tegra-asoc: sound: ADMAIF10 <-2789-1-test> ADMAIF10 mapping ok [ 2.355922] tegra-asoc: sound: ADMAIF11 <-2789-1-test> ADMAIF11 mapping ok [ 2.356034] tegra-asoc: sound: ADMAIF12 <-2789-1-test> ADMAIF12 mapping ok [ 2.356130] tegra-asoc: sound: ADMAIF13 <-2789-1-test> ADMAIF13 mapping ok [ 2.356219] tegra-asoc: sound: ADMAIF14 <-2789-1-test> ADMAIF14 mapping ok [ 2.356302] tegra-asoc: sound: ADMAIF15 <-2789-1-test> ADMAIF15 mapping ok [ 2.356422] tegra-asoc: sound: ADMAIF16 <-2789-1-test> ADMAIF16 mapping ok [ 2.356515] tegra-asoc: sound: ADMAIF17 <-2789-1-test> ADMAIF17 mapping ok [ 2.356598] tegra-asoc: sound: ADMAIF18 <-2789-1-test> ADMAIF18 mapping ok [ 2.356677] tegra-asoc: sound: ADMAIF19 <-2789-1-test> ADMAIF19 mapping ok [ 2.356775] tegra-asoc: sound: ADMAIF20 <-2789-1-test> ADMAIF20 mapping ok [ 2.385484] u32 classifier [ 2.385489] Actions configured [ 2.385557] Initializing XFRM netlink socket [ 2.386186] NET: Registered protocol family 10 [ 2.386941] NET: Registered protocol family 17 [ 2.386954] NET: Registered protocol family 15 [ 2.387006] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.387080] Bluetooth: RFCOMM socket layer initialized [ 2.387094] Bluetooth: RFCOMM ver 1.11 [ 2.387099] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.387105] Bluetooth: HIDP socket layer initialized [ 2.387123] 9pnet: Installing 9P2000 support [ 2.387161] Key type dns_resolver registered [ 2.387474] Registered cp15_barrier emulation handler [ 2.387495] Registered setend emulation handler [ 2.388998] registered taskstats version 1 [ 2.389475] tegra-pcie-dw 14160000.pcie: Setting init speed to max speed [ 2.390420] OF: PCI: host bridge /pcie@14160000 ranges: [ 2.390438] OF: PCI: IO 0x36100000..0x361fffff -> 0x36100000 [ 2.390446] OF: PCI: MEM 0x1740000000..0x17ffffffff -> 0x40000000 [ 2.390452] OF: PCI: MEM 0x1400000000..0x173fffffff -> 0x1400000000 [ 2.604426] usb 1-3.2: new high-speed USB device number 3 using tegra-xusb [ 2.627240] usb 1-3.2: New USB device found, idVendor=05e3, idProduct=0610 [ 2.627248] usb 1-3.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.627253] usb 1-3.2: Product: USB2.0 Hub [ 2.627257] usb 1-3.2: Manufacturer: GenesysLogic [ 2.628080] hub 1-3.2:1.0: USB hub found [ 2.628388] hub 1-3.2:1.0: 4 ports detected [ 2.676427] tegra_cec 3960000.tegra_cec: physical address: 10:00. [ 2.740951] tegra_cec 3960000.tegra_cec: Sent res: -113. [ 2.740958] tegra_cec 3960000.tegra_cec: tegra_cec_init Done. [ 2.805119] FAN rising trip_level:2 cur_temp:64000 trip_temps[3]:68000 [ 2.900843] tegra-pcie-dw 14160000.pcie: link is down [ 2.901031] tegra-pcie-dw 14160000.pcie: PCI host bridge to bus 0004:00 [ 2.901040] pci_bus 0004:00: root bus resource [bus 00-ff] [ 2.901048] pci_bus 0004:00: root bus resource [io 0x0000-0xfffff] (bus address [0x36100000-0x361fffff]) [ 2.901054] pci_bus 0004:00: root bus resource [mem 0x1740000000-0x17ffffffff] (bus address [0x40000000-0xffffffff]) [ 2.901058] pci_bus 0004:00: root bus resource [mem 0x1400000000-0x173fffffff pref] [ 2.901085] pci 0004:00:00.0: [10de:1ad1] type 01 class 0x060400 [ 2.901275] pci 0004:00:00.0: PME# supported from D0 D3hot D3cold [ 2.901540] iommu: Adding device 0004:00:00.0 to group 59 [ 2.901828] pci 0004:00:00.0: PCI bridge to [bus 01-ff] [ 2.901853] pci 0004:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 512 [ 2.902050] pcieport 0004:00:00.0: Signaling PME through PCIe PME interrupt [ 2.902057] pcie_pme 0004:00:00.0:pcie001: service driver pcie_pme loaded [ 2.902130] aer 0004:00:00.0:pcie002: service driver aer loaded [ 2.902292] pcie_pme 0004:00:00.0:pcie001: unloading service driver pcie_pme [ 2.902385] aer 0004:00:00.0:pcie002: unloading service driver aer [ 2.902507] pci_bus 0004:01: busn_res: [bus 01-ff] is released [ 2.902617] iommu: Removing device 0004:00:00.0 from group 59 [ 2.902680] pci_bus 0004:00: busn_res: [bus 00-ff] is released [ 2.904497] tegra-pcie-dw 14160000.pcie: PCIe link is not up...! [ 2.905230] tegra-pcie-dw 141a0000.pcie: Setting init speed to max speed [ 2.906203] OF: PCI: host bridge /pcie@141a0000 ranges: [ 2.906218] OF: PCI: IO 0x3a100000..0x3a1fffff -> 0x3a100000 [ 2.906226] OF: PCI: MEM 0x1f40000000..0x1fffffffff -> 0x40000000 [ 2.906232] OF: PCI: MEM 0x1c00000000..0x1f3fffffff -> 0x1c00000000 [ 2.916415] usb 1-3.2.2: new low-speed USB device number 4 using tegra-xusb [ 2.940513] usb 1-3.2.2: New USB device found, idVendor=04ca, idProduct=0061 [ 2.940519] usb 1-3.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.940523] usb 1-3.2.2: Product: USB Optical Mouse [ 2.940527] usb 1-3.2.2: Manufacturer: PixArt [ 2.943173] input: PixArt USB Optical Mouse as /devices/3610000.xhci/usb1/1-3/1-3.2/1-3.2.2/1-3.2.2:1.0/0003:04CA:0061.0001/input/input4 [ 2.943385] hid-generic 0003:04CA:0061.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-3610000.xhci-3.2.2/input0 [ 3.020392] usb 1-3.2.3: new low-speed USB device number 5 using tegra-xusb [ 3.047093] usb 1-3.2.3: New USB device found, idVendor=413c, idProduct=2113 [ 3.047100] usb 1-3.2.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 3.047104] usb 1-3.2.3: Product: Dell KB216 Wired Keyboard [ 3.051301] input: Dell KB216 Wired Keyboard as /devices/3610000.xhci/usb1/1-3/1-3.2/1-3.2.3/1-3.2.3:1.0/0003:413C:2113.0002/input/input5 [ 3.108901] hid-generic 0003:413C:2113.0002: input,hidraw1: USB HID v1.11 Keyboard [Dell KB216 Wired Keyboard] on usb-3610000.xhci-3.2.3/input0 [ 3.113722] input: Dell KB216 Wired Keyboard as /devices/3610000.xhci/usb1/1-3/1-3.2/1-3.2.3/1-3.2.3:1.1/0003:413C:2113.0003/input/input6 [ 3.172619] hid-generic 0003:413C:2113.0003: input,hidraw2: USB HID v1.11 Device [Dell KB216 Wired Keyboard] on usb-3610000.xhci-3.2.3/input1 [ 3.253063] usb 1-3.2.4: new high-speed USB device number 6 using tegra-xusb [ 3.420502] tegra-pcie-dw 141a0000.pcie: link is down [ 3.420616] tegra-pcie-dw 141a0000.pcie: PCI host bridge to bus 0005:00 [ 3.420624] pci_bus 0005:00: root bus resource [bus 00-ff] [ 3.420632] pci_bus 0005:00: root bus resource [io 0x100000-0x1fffff] (bus address [0x3a100000-0x3a1fffff]) [ 3.420638] pci_bus 0005:00: root bus resource [mem 0x1f40000000-0x1fffffffff] (bus address [0x40000000-0xffffffff]) [ 3.420642] pci_bus 0005:00: root bus resource [mem 0x1c00000000-0x1f3fffffff pref] [ 3.420673] pci 0005:00:00.0: [10de:1ad0] type 01 class 0x060400 [ 3.420823] pci 0005:00:00.0: PME# supported from D0 D3hot D3cold [ 3.421049] iommu: Adding device 0005:00:00.0 to group 59 [ 3.421282] pci 0005:00:00.0: PCI bridge to [bus 01-ff] [ 3.421305] pci 0005:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 512 [ 3.421497] pcieport 0005:00:00.0: Signaling PME through PCIe PME interrupt [ 3.421504] pcie_pme 0005:00:00.0:pcie001: service driver pcie_pme loaded [ 3.421583] aer 0005:00:00.0:pcie002: service driver aer loaded [ 3.421731] pcie_pme 0005:00:00.0:pcie001: unloading service driver pcie_pme [ 3.421778] aer 0005:00:00.0:pcie002: unloading service driver aer [ 3.421851] pci_bus 0005:01: busn_res: [bus 01-ff] is released [ 3.421939] iommu: Removing device 0005:00:00.0 from group 59 [ 3.421966] pci_bus 0005:00: busn_res: [bus 00-ff] is released [ 3.423826] tegra-pcie-dw 141a0000.pcie: PCIe link is not up...! [ 3.432951] tegra-cbb 14040000.cv-noc: noc_secure_irq = 91, noc_nonsecure_irq = 90> [ 3.437857] tegra194-isp5 14800000.isp: initialized [ 3.444182] tegra194-vi5 15c10000.vi: using default number of vi channels, 36 [ 3.446900] tegra194-vi5 15c10000.vi: initialized [ 3.450978] tegra194-vi5 15c10000.vi: subdev 15a00000.nvcsi--2 bound [ 3.451088] tegra194-vi5 15c10000.vi: subdev 15a00000.nvcsi--1 bound [ 3.451299] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 3.451733] tegra-thermal-throttle bthrot_cdev: clk:cpu max:1907200000, min:115200000 steps:24 [ 3.455940] tegra-thermal-throttle bthrot_cdev: clk:gpu max:1109250000, min:114750000 steps:10 [ 3.455953] tegra-thermal-throttle bthrot_cdev: cdev:skin-balanced clk:0:cpu off:0 slope-adj:200 [ 3.455957] tegra-thermal-throttle bthrot_cdev: cdev:skin-balanced clk:1:gpu off:0 slope-adj:400 [ 3.456036] tegra-thermal-throttle bthrot_cdev: cdev:skin-balanced max_state:48 cutoff:0 [ 3.456060] tegra-thermal-throttle bthrot_cdev: cdev:gpu-balanced clk:0:cpu off:0 slope-adj:400 [ 3.456065] tegra-thermal-throttle bthrot_cdev: cdev:gpu-balanced clk:1:gpu off:0 slope-adj:400 [ 3.460252] tegra-thermal-throttle bthrot_cdev: cdev:gpu-balanced max_state:40 cutoff:1 [ 3.460285] tegra-thermal-throttle bthrot_cdev: cdev:cpu-balanced clk:0:cpu off:0 slope-adj:200 [ 3.460290] tegra-thermal-throttle bthrot_cdev: cdev:cpu-balanced clk:1:gpu off:365500000 slope-adj:300 [ 3.460625] tegra-thermal-throttle bthrot_cdev: cdev:cpu-balanced max_state:48 cutoff:0 [ 3.460649] tegra-thermal-throttle bthrot_cdev: cdev:emergency-balanced clk:0:cpu off:38400000 slope-adj:10 [ 3.460653] tegra-thermal-throttle bthrot_cdev: cdev:emergency-balanced clk:1:gpu off:25500000 slope-adj:10 [ 3.460997] tegra-thermal-throttle bthrot_cdev: cdev:emergency-balanced max_state:2 cutoff:0 [ 3.461024] tegra-thermal-throttle bthrot_cdev: cdev:aux-balanced clk:0:cpu off:0 slope-adj:400 [ 3.461028] tegra-thermal-throttle bthrot_cdev: cdev:aux-balanced clk:1:gpu off:0 slope-adj:400 [ 3.461240] tegra-thermal-throttle bthrot_cdev: cdev:aux-balanced max_state:40 cutoff:1 [ 3.462046] tegra186-cam-rtcpu bc00000.rtcpu: Trace buffer configured at IOVA=0xbff00000 [ 3.491115] usb 1-3.2.4: New USB device found, idVendor=046d, idProduct=0825 [ 3.491123] usb 1-3.2.4: New USB device strings: Mfr=0, Product=0, SerialNumber=2 [ 3.491128] usb 1-3.2.4: SerialNumber: F546EDC0 [ 3.546555] tegra-ivc ivc-bc00000.rtcpu: region 0: iova=0xbfee0000-0xbfefffff size=131072 [ 3.546941] tegra-ivc ivc-bc00000.rtcpu:echo@0: echo: ver=0 grp=1 RX[16x64]=0x1000-0x1480 TX[16x64]=0x1480-0x1900 [ 3.547166] tegra-ivc ivc-bc00000.rtcpu:dbg@1: dbg: ver=0 grp=1 RX[1x384]=0x1900-0x1b00 TX[1x384]=0x1b00-0x1d00 [ 3.547353] tegra-ivc ivc-bc00000.rtcpu:dbg@2: dbg: ver=0 grp=1 RX[1x8192]=0x1d00-0x3d80 TX[1x8192]=0x3d80-0x5e00 [ 3.547657] tegra-ivc ivc-bc00000.rtcpu:ivccontrol@3: ivccontrol: ver=0 grp=1 RX[64x320]=0x5e00-0xae80 TX[64x320]=0xae80-0xff00 [ 3.547796] tegra-ivc ivc-bc00000.rtcpu:ivccapture@4: ivccapture: ver=0 grp=1 RX[512x64]=0xff00-0x17f80 TX[512x64]=0x17f80-0x20000 [ 3.547990] tegra186-cam-rtcpu bc00000.rtcpu: using cam RTCPU IRQ (66) [ 3.547994] tegra186-cam-rtcpu bc00000.rtcpu: tegra_camrtc_mon_create is successful [ 3.549048] tegra186-cam-rtcpu bc00000.rtcpu: firmware version cpu=rce cmd=5 sha1=cf2bef3ad10e437272857b76308abef8ffb80bda [ 3.549273] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 3.549982] Wake83 for irq=211 [ 3.550046] gpio tegra-gpio wake67 for gpio=48(G:0) [ 3.550133] gpio tegra-gpio-aon wake29 for gpio=36(EE:4) [ 3.550288] input: gpio-keys as /devices/gpio-keys/input/input7 [ 3.550756] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 3.581457] tegra_rtc c2a0000.rtc: setting system clock to 2021-08-05 10:11:53 UTC (1628158313) [ 3.581893] mmcblk mmc0:0001: Card claimed for testing. [ 3.613775] bpmp: mounted debugfs mirror [ 3.620097] ALSA device list: [ 3.620106] #0: tegra-hda-xnx at 0x3518000 irq 65 [ 3.620110] #1: jetson-xaviernx-ape [ 3.622282] Freeing unused kernel memory: 8576K [ 3.660893] Root device found: mmcblk0p1 [ 3.662584] Found dev node: /dev/mmcblk0p1 [ 3.685140] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 3.687682] Rootfs mounted over mmcblk0p1 [ 3.711348] Switching from initrd to actual rootfs [ 3.836261] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.840341] cgroup: cgroup2: unknown option "nsdelegate" [ 3.849480] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 3.850142] systemd[1]: Detected architecture arm64. [ 3.858045] systemd[1]: Set hostname to . [ 3.943888] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 3.943901] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 4.083089] random: systemd: uninitialized urandom read (16 bytes read) [ 4.083125] systemd[1]: Reached target Swap. [ 4.083545] random: systemd: uninitialized urandom read (16 bytes read) [ 4.083910] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 4.083949] random: systemd: uninitialized urandom read (16 bytes read) [ 4.083971] systemd[1]: Reached target User and Group Name Lookups. [ 4.086609] systemd[1]: Created slice User and Session Slice. [ 4.086811] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 4.128768] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 4.222314] nvgpu: 17000000.gv11b nvgpu_nvhost_syncpt_init:291 [INFO] syncpt_unit_base 60000000 syncpt_unit_size 400000 size 1000 [ 4.244794] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 4.248490] cpu-throttle-alert cooling device registered. [ 4.248971] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 4.249422] gpu-throttle-alert cooling device registered. [ 4.249618] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 4.250194] aux-throttle-alert cooling device registered. [ 4.250369] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 4.502943] systemd-journald[2414]: Received request to flush runtime journal from PID 1 [ 4.831696] usb 1-3.2.4: set resolution quirk: cval->res = 384 [ 4.832684] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 5.044664] FAN rising trip_level:3 cur_temp:69100 trip_temps[4]:76000 [ 5.155167] using random self ethernet address [ 5.155327] using random host ethernet address [ 5.653687] random: crng init done [ 5.653839] random: 7 urandom warning(s) missed due to ratelimiting [ 5.683746] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 5.701034] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 5.701978] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 5.703609] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 5.820012] Mass Storage Function, version: 2009/09/11 [ 5.820021] LUN: removable file: (no medium) [ 5.826449] using random self ethernet address [ 5.826618] using random host ethernet address [ 5.890881] rndis0: HOST MAC 8e:f8:b3:4c:e6:74 [ 5.891345] rndis0: MAC 8e:f8:b3:4c:e6:75 [ 5.892537] usb0: HOST MAC 8e:f8:b3:4c:e6:76 [ 5.892761] usb0: MAC 8e:f8:b3:4c:e6:77 [ 5.892790] tegra-xudc-new 3550000.xudc: exiting ELPG [ 5.893719] tegra-xudc-new 3550000.xudc: exiting ELPG done [ 5.893738] tegra-xudc-new 3550000.xudc: ep 0 (type: 0, dir: out) enabled [ 5.893777] tegra-xudc-new 3550000.xudc: entering ELPG [ 5.893986] tegra-xudc-new 3550000.xudc: entering ELPG done [ 5.894001] tegra-xudc-new 3550000.xudc: exiting ELPG [ 5.894436] tegra-xudc-new 3550000.xudc: exiting ELPG done [ 5.894450] tegra-xudc-new 3550000.xudc: entering ELPG [ 5.894712] tegra-xudc-new 3550000.xudc: entering ELPG done [ 5.898709] l4tbr0: port 1(rndis0) entered blocking state [ 5.898716] l4tbr0: port 1(rndis0) entered disabled state [ 5.898925] device rndis0 entered promiscuous mode [ 5.904867] IPv6: ADDRCONF(NETDEV_UP): rndis0: link is not ready [ 5.909779] l4tbr0: port 2(usb0) entered blocking state [ 5.909786] l4tbr0: port 2(usb0) entered disabled state [ 5.909969] device usb0 entered promiscuous mode [ 5.914971] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 6.049480] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.073217] ras_fhi_disable: FHI 474 disabled [ 6.075172] CPU4: shutdown [ 6.075304] psci: CPU4 killed. [ 6.160258] ras_fhi_disable: FHI 475 disabled [ 6.166955] CPU5: shutdown [ 6.184422] psci: Retrying again to check for CPU kill [ 6.184442] psci: CPU5 killed. [ 6.186236] nvgpu: 17000000.gv11b tpc_pg_mask_store:843 [INFO] no value change, same mask already set [ 6.361264] gpio tegra-gpio wake20 for gpio=52(G:4) [ 6.365434] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.488950] zram: Added device: zram0 [ 6.491382] zram: Added device: zram1 [ 6.492995] zram: Added device: zram2 [ 6.500757] zram: Added device: zram3 [ 6.559676] zram0: detected capacity change from 0 to 1017851904 [ 6.597682] Adding 993992k swap on /dev/zram0. Priority:5 extents:1 across:993992k SS [ 6.608002] zram1: detected capacity change from 0 to 1017851904 [ 6.626093] Adding 993992k swap on /dev/zram1. Priority:5 extents:1 across:993992k SS [ 6.631789] zram2: detected capacity change from 0 to 1017851904 [ 6.648302] Adding 993992k swap on /dev/zram2. Priority:5 extents:1 across:993992k SS [ 6.653173] zram3: detected capacity change from 0 to 1017851904 [ 6.686648] Adding 993992k swap on /dev/zram3. Priority:5 extents:1 across:993992k SS [ 7.333374] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 7.333976] uvcvideo: Found UVC 1.00 device (046d:0825) [ 7.351517] uvcvideo 1-3.2.4:1.0: Entity type for entity Extension 4 was not initialized! [ 7.351702] uvcvideo 1-3.2.4:1.0: Entity type for entity Extension 6 was not initialized! [ 7.351844] uvcvideo 1-3.2.4:1.0: Entity type for entity Extension 7 was not initialized! [ 7.351993] uvcvideo 1-3.2.4:1.0: Entity type for entity Processing 2 was not initialized! [ 7.352138] uvcvideo 1-3.2.4:1.0: Entity type for entity Extension 3 was not initialized! [ 7.352286] uvcvideo 1-3.2.4:1.0: Entity type for entity Camera 1 was not initialized! [ 7.360604] input: UVC Camera (046d:0825) as /devices/3610000.xhci/usb1/1-3/1-3.2/1-3.2.4/1-3.2.4:1.0/input/input8 [ 7.361164] generic-pwm-tachometer generic_pwm_tachometer: Failed to get pwm: -517 [ 7.361662] usbcore: registered new interface driver uvcvideo [ 7.361667] USB Video Class driver (1.1.1) [ 7.581769] tegradc 15200000.nvdisplay: unblank [ 7.581782] tegradc 15210000.nvdisplay: blank - powerdown [ 8.596708] fuse init (API version 7.26) [ 10.216476] usb 1-3.2.4: usb_suspend_both: status 0 [ 10.540654] usb 1-3.2.4: reset high-speed USB device number 6 using tegra-xusb [ 12.317407] eqos 2490000.ether_qos eth0: Link is Up - 100Mbps/Full - flow control off [ 12.318034] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 12.856725] FAN rising trip_level:2 cur_temp:66150 trip_temps[3]:68000 [ 13.182313] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 13.182331] Bluetooth: BNEP socket layer initialized [ 20.328435] usb 1-3.2.4: usb_suspend_both: status 0 [ 34.132632] vdd-1v8-cvb: disabling [ 34.132641] vdd-epb-1v0: disabling [ 34.132646] avdd-cam-2v8: disabling [ 34.132674] vdd_sys_en: disabling [ 102.188778] mmc1: fallback to HS enumeration. [ 102.494472] mmc1: error -110 whilst initialising SD card [ 103.099361] mmc1: fallback to HS enumeration. [ 103.587430] mmc1: error -110 whilst initialising SD card [ 104.147525] mmc1: fallback to HS enumeration. [ 104.645538] mmc1: error -110 whilst initialising SD card [ 105.189532] mmc1: fallback to HS enumeration. [ 105.681440] mmc1: error -110 whilst initialising SD card [ 105.690270] tegradc 15200000.nvdisplay: blank - powerdown [ 105.753866] extcon-disp-state external-connection:disp-state: cable 47 state 0 [ 105.753871] Extcon AUX1(HDMI) disable [ 105.783493] tegra_nvdisp_handle_pd_disable: Powergated Head1 pd [ 105.786467] tegra_nvdisp_handle_pd_disable: Powergated Head0 pd [ 105.787023] tegradc 15210000.nvdisplay: blank - powerdown [ 105.945170] tegradc 15200000.nvdisplay: blank - powerdown [ 105.945186] tegradc 15200000.nvdisplay: unblank [ 105.946171] tegra_nvdisp_handle_pd_enable: Unpowergated Head0 pd [ 105.946302] tegra_nvdisp_handle_pd_enable: Unpowergated Head1 pd [ 105.948045] Parent Clock set for DC plld2 [ 105.952466] tegradc 15200000.nvdisplay: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_111m_223m [ 105.954126] tegradc 15200000.nvdisplay: hdmi: get YCC quant from EDID. [ 105.990322] extcon-disp-state external-connection:disp-state: cable 47 state 1 [ 105.990326] Extcon AUX1(HDMI) enable [ 105.991072] tegradc 15200000.nvdisplay: unblank [ 105.991098] tegradc 15210000.nvdisplay: blank - powerdown [ 106.235245] mmc1: fallback to HS enumeration. [ 106.718798] mmc1: error -110 whilst initialising SD card [ 107.260412] mmc1: fallback to HS enumeration. [ 107.748446] mmc1: error -110 whilst initialising SD card [ 108.300610] mmc1: fallback to HS enumeration. [ 108.806969] mmc1: error -110 whilst initialising SD card [ 109.260484] usb 1-3.2.4: reset high-speed USB device number 6 using tegra-xusb [ 109.290647] tegradc 15200000.nvdisplay: unblank [ 109.290659] tegradc 15210000.nvdisplay: blank - powerdown [ 115.895676] FAN rising trip_level:3 cur_temp:68450 trip_temps[4]:76000 [ 119.403819] usb 1-3.2.4: usb_suspend_both: status 0 [ 383.575666] FAN cooling trip_level:2 cur_temp:60900 trip_temps[3]:68000 [ 466.511306] tegradc 15200000.nvdisplay: blank - powerdown [ 466.571581] extcon-disp-state external-connection:disp-state: cable 47 state 0 [ 466.571586] Extcon AUX1(HDMI) disable [ 466.595994] tegra_nvdisp_handle_pd_disable: Powergated Head1 pd [ 466.597066] tegra_nvdisp_handle_pd_disable: Powergated Head0 pd [ 645.656415] FAN cooling trip_level:1 cur_temp:51800 trip_temps[2]:60000