[0000.126] [TegraBoot] (version 00.00.2018.01-l4t-89b97a49) [0000.131] Processing in cold boot mode Bootloader 2 [0000.136] A02 Bootrom Patch rev = 1023 [0000.140] Power-up reason: pmc por [0000.143] No Battery Present [0000.145] pmic max77620 reset reason [0000.149] pmic max77620 NVERC : 0x50 [0000.152] RamCode = 2 [0000.154] Platform has DDR4 type RAM [0000.158] max77620 disabling SD1 Remote Sense [0000.162] Setting DDR voltage to 1125mv [0000.166] Serial Number of Pmic Max77663: 0x2432e6 [0000.174] Entering ramdump check [0000.177] Get RamDumpCarveOut = 0x0 [0000.180] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.185] Last reboot was clean, booting normally! [0000.190] Sdram initialization is successful [0000.194] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.200] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.206] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.217] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.223] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.229] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.235] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.251] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.257] Platform-DebugCarveout: 0 [0000.260] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.266] Non secure mode, and RB not enabled. [0000.321] Csd NumOfBlocks=30375936 [0000.325] Set High speed to 1 [0000.335] Using GPT Primary to query partitions [0000.340] Loading Tboot-CPU binary [0000.352] Verifying TBC in OdmNonSecureSBK mode [0000.362] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.369] Bootloader downloaded successfully. [0000.373] Downloaded Tboot-CPU binary to 0xa0000258 [0000.378] MAX77620_GPIO5 configured [0000.382] CPU power rail is up [0000.384] CPU clock enabled [0000.388] Performing RAM repair [0000.391] Updating A64 Warmreset Address to 0xa00002e9 [0000.396] Loading NvTbootBootloaderDTB [0000.432] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.497] Bootloader DTB Load Address: 0x83000000 [0000.502] Loading NvTbootKernelDTB [0000.538] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.603] Kernel DTB Load Address: 0x83100000 [0000.608] Loading cboot binary [0000.651] Verifying EBT in OdmNonSecureSBK mode [0000.693] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.700] Bootloader downloaded successfully. [0000.705] Next binary entry address: 0x92c00258 [0000.709] BoardId: 3448 [0000.714] Overriding pmu board id with proc board id [0000.718] Display board id is not available [0000.759] Verifying SC7EntryFw in OdmNonSecureSBK mode [0000.811] /bpmp deleted [0000.814] SC7EntryFw header found loaded at 0xff700000 [0001.004] OVR2 PMIC [0001.006] Bpmp FW successfully loaded [0001.010] WB0 init successfully at 0xff780000 [0001.014] Set NvDecSticky Bits [0001.018] GSC2 address ff53fffc value c0edbbcc [0001.024] GSC MC Settings done [0001.027] TOS Image length 53680 [0001.031] Monitor size 53680 [0001.033] OS size 0 [0001.042] Secure Os AES-CMAC Verification Success! [0001.046] TOS image cipher info: plaintext [0001.050] Loading and Validation of Secure OS Successful [0001.066] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.071] NvTbootPackSdramParams: start. [0001.076] NvTbootPackSdramParams: done. [0001.080] Tegraboot started after 53763 us [0001.084] Basic modules init took 686820 us [0001.088] NvTbootQspiFlashIoctl: Opcode = 1 not supported [0001.093] Sec Bootdevice Read Time = 622327755 ms, Read Size = 622327755 KB [0001.100] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.105] Storage Device Read Time = 164 ms, Read Size = 2241 KB [0001.111] Storage Device Write Time = 0 ms, Write Size = 0 KB [0001.117] Next stage binary read took 37576 us [0001.121] Carveout took -49239 us [0001.124] CPU initialization took 377120 us [0001.128] Total time taken by TegraBoot 1052277 us [0001.133] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):fe06da916 NOTICE: BL31: Built : 18:04:17, Apr 8 2020 ERROR: Error initializing runtime service trusty_fast [0001.255] RamCode = 2 [0001.257] get_emc_table_offset: Can't find emc-table node [0001.262] LPDDR4 Training: Can't find emc-table node [0001.301] [0001.302] Debug Init done [0001.305] Marked DTB cacheable [0001.308] Bootloader DTB loaded at 0x83000000 [0001.313] Marked DTB cacheable [0001.315] Kernel DTB loaded at 0x83100000 [0001.319] DeviceTree Init done [0001.335] Pinmux applied successfully [0001.339] gicd_base: 0x50041000 [0001.343] gicc_base: 0x50042000 [0001.346] Interrupts Init done [0001.350] Using base:0x60005090 & irq:208 for tick-timer [0001.355] Using base:0x60005098 for delay-timer [0001.360] platform_init_timer: DONE [0001.363] Timer(tick) Init done [0001.367] osc freq = 38400 khz [0001.371] [0001.372] Welcome to L4T Cboot [0001.375] [0001.376] Cboot Version: 00.00.2018.01-t210-40c3ff9c [0001.381] calling constructors [0001.384] initializing heap [0001.387] initializing threads [0001.390] initializing timers [0001.393] creating bootstrap completion thread [0001.397] top of bootstrap2() [0001.400] CPU: ARM Cortex A57 [0001.403] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.407] initializing platform [0001.415] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.420] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.424] Macronix QSPI chip present [0001.428] SPI device register [0001.430] init boot device [0001.433] allocating memory for boot device(SPI) [0001.438] registering boot device [0001.447] sdmmc node status = okay [0001.450] sdcard instance = 0 [0001.453] sdcard gpio handle 0x56 [0001.456] sdcard gpio pin 0xc9 [0001.459] sdcard gpio flags 0x0 [0001.462] vmmc-supply 0x99 [0001.465] Instance: 0 [0001.467] Allocating memory for context [0001.471] enabling clock [0001.473] sd card init [0001.476] Check card present and stable [0001.479] Send command 0 [0001.496] Send command 3 [0001.500] Set RCA for the card [0001.503] Query card specific data by command 9 [0001.509] Parse CSD data [0001.512] Send command 7 [0001.522] Calling sd device register [0001.526] Init sdcard [0001.528] Allocating memory for boot device [0001.532] Registering user device [0001.545] Enable APE clock [0001.548] Un-powergate APE partition [0001.551] of_register: registering tegra_udc to of_hal [0001.556] of_register: registering inv20628-driver to of_hal [0001.562] of_register: registering ads1015-driver to of_hal [0001.567] of_register: registering lp8557-bl-driver to of_hal [0001.573] of_register: registering bq2419x_charger to of_hal [0001.579] of_register: registering bq27441_fuel_gauge to of_hal [0001.590] gpio framework initialized [0001.594] of_register: registering tca9539_gpio to of_hal [0001.599] of_register: registering tca9539_gpio to of_hal [0001.605] of_register: registering i2c_bus_driver to of_hal [0001.610] of_register: registering i2c_bus_driver to of_hal [0001.616] of_register: registering i2c_bus_driver to of_hal [0001.621] pmic framework initialized [0001.625] of_register: registering max77620_pmic to of_hal [0001.630] regulator framework initialized [0001.634] of_register: registering tps65132_bl_driver to of_hal [0001.640] initializing target [0001.646] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.654] board ID = D78, board SKU = 0 [0001.658] Skipping Z3! [0001.662] fixed regulator driver initialized [0001.680] initializing OF layer [0001.683] NCK carveout not present [0001.686] Skipping dts_overrides [0001.690] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.707] I2C Bus Init done [0001.710] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.720] I2C Bus Init done [0001.723] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.733] I2C Bus Init done [0001.736] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.746] I2C Bus Init done [0001.749] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.759] I2C Bus Init done [0001.762] of_children_init: Ops found for compatible string maxim,max77620 [0001.772] max77620_init using irq 118 [0001.777] register 'maxim,max77620' pmic [0001.781] gpio_driver_register: register 'max77620-gpio' driver [0001.788] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.798] I2C Bus Init done [0001.802] NCK carveout not present [0001.812] Find /i2c@7000c000's alias i2c0 [0001.816] get eeprom at 1-a0, size 256, type 0 [0001.824] Find /i2c@7000c500's alias i2c2 [0001.828] get eeprom at 3-a0, size 256, type 0 [0001.833] get eeprom at 3-ae, size 256, type 0 [0001.837] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.842] I2C slave not started [0001.845] I2C write failed [0001.848] Writing offset failed [0001.851] eeprom_init: EEPROM read failed [0001.855] pm_ids_update: eeprom init failed [0001.859] pm_ids_update: Updating 3,a0, size 256, type 0 [0001.889] pm_ids_update: The pm board id is 3448-0000-200 [0001.896] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0001.904] pm_ids_update: pm id update successful [0001.908] pm_ids_update: Updating 3,ae, size 256, type 0 [0001.914] I2C slave not started [0001.917] I2C write failed [0001.919] Writing offset failed [0001.922] eeprom_init: EEPROM read failed [0001.926] pm_ids_update: eeprom init failed [0001.956] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0001.962] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0001.971] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0001.976] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0001.985] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e4:39:31 [0001.991] Plugin Manager: Parse ODM data 0x00094000 [0002.002] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0002.023] Find /i2c@7000c000's alias i2c0 [0002.027] get eeprom at 1-a0, size 256, type 0 [0002.036] Find /i2c@7000c500's alias i2c2 [0002.040] get eeprom at 3-a0, size 256, type 0 [0002.044] get eeprom at 3-ae, size 256, type 0 [0002.048] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.054] I2C slave not started [0002.057] I2C write failed [0002.059] Writing offset failed [0002.062] eeprom_init: EEPROM read failed [0002.066] pm_ids_update: eeprom init failed [0002.071] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.101] pm_ids_update: The pm board id is 3448-0000-200 [0002.107] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0002.114] pm_ids_update: pm id update successful [0002.119] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.124] I2C slave not started [0002.127] I2C write failed [0002.130] Writing offset failed [0002.133] eeprom_init: EEPROM read failed [0002.137] pm_ids_update: eeprom init failed [0002.167] Add serial number:0421519013463 as DT property [0002.175] Applying platform configs [0002.181] platform-init is not present. Skipping [0002.186] calling apps_init() [0002.211] Found 14 GPT partitions in "sd0" [0002.215] Proceeding to Cold Boot [0002.218] starting app android_boot_app [0002.222] Device state: unlocked [0002.225] display console init [0002.234] could not find regulator [0002.237] hdmi cable connected [0002.240] I2C slave not started [0002.243] I2C write failed [0002.246] Writing offset failed [0002.249] could not read edid [0002.253] tmds-config node not found [0002.257] pmc_set_io_pad_voltage: Error -2 retrieving platfDT entry for leds-pwm not found o[0002.269] rm-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.279] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.287] could not find regulator [0002.290] could not find regulator [0002.293] could not find regulator [0002.322] using default cmu settings [0002.326] dc_hdmi_enable, starting HDMI initialisation [0002.332] dc_hdmi_enable, HDMI initialisation complete [0002.337] list and configure display window [0002.342] display console init completed [0002.349] subnode volume_up is not found ! [0002.353] subnode back is not found ! [0002.356] subnode volume_down is not found ! [0002.361] subnode menu is not found ! [0002.364] Gpio keyboard init success [0002.396] found decompressor handler: lz4-legacy [0002.411] decompressing blob (type 1)... [0002.445] load_bmp_blob: panelresolution=480 type=0 [0002.484] decompressor handler not found [0002.488] load_firmware_blob: Firmware blob loaded, entries=2 [0002.493] -------> se_aes_verify_sbk_clear: 747 [0002.498] se_aes_verify_sbk_clear: Error [0002.502] bl_battery_charging: connected to external power supply [0002.509] xusb is supported [0002.515] error while finding nvidia,portmap [0003.019] xusb blob version 0 size 124416 [0003.023] firmware size 124416 [0003.028] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0003.043] xhci0: 64 bytes context size, 32-bit DMA [0003.083] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.103] uhub0: on usbus0 [0003.753] uhub0: 9 ports with 9 removable, self powered [0004.753] failed to get HID devices [0004.756] failed to init xhci or no usb device attached [0004.764] device_query_partition_size: failed to open partition sd0:MSC ! [0004.770] MSC Partition not found [0004.774] device_query_partition_size: failed to open partition sd0:USP ! [0004.780] USP partition read failed! [0004.784] blob_init: blob-partition USP header read failed [0004.789] android_boot Unable to update recovery partition [0004.795] kfs_getpartname: name = LNX [0004.798] Loading kernel from LNX [0004.894] load kernel from storage [0004.905] decompressor handler not found [0004.963] Successfully loaded kernel and ramdisk images [0004.969] load_bmp_blob: panelresolution=480 type=0 [0005.043] display bmp image done [0005.046] NCK carveout not present [0005.049] Skipping dts_overrides [0005.052] NCK carveout not present [0005.062] Find /i2c@7000c000's alias i2c0 [0005.066] get eeprom at 1-a0, size 256, type 0 [0005.075] Find /i2c@7000c500's alias i2c2 [0005.079] get eeprom at 3-a0, size 256, type 0 [0005.083] get eeprom at 3-ae, size 256, type 0 [0005.088] pm_ids_update: Updating 1,a0, size 256, type 0 [0005.093] I2C slave not started [0005.096] I2C write failed [0005.099] Writing offset failed [0005.102] eeprom_init: EEPROM read failed [0005.106] pm_ids_update: eeprom init failed [0005.110] pm_ids_update: Updating 3,a0, size 256, type 0 [0005.140] pm_ids_update: The pm board id is 3448-0000-200 [0005.147] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0005.155] pm_ids_update: pm id update successful [0005.159] pm_ids_update: Updating 3,ae, size 256, type 0 [0005.164] I2C slave not started [0005.167] I2C write failed [0005.170] Writing offset failed [0005.173] eeprom_init: EEPROM read failed [0005.177] pm_ids_update: eeprom init failed [0005.207] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.213] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0005.221] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.227] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0005.236] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e4:39:31 [0005.242] Plugin Manager: Parse ODM data 0x00094000 [0005.252] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.267] Add serial number:0421519013463 as DT property [0005.276] "bpmp" doesn't exist, creating [0005.282] Updated bpmp info to DTB [0005.287] Updated initrd info to DTB [0005.290] "proc-board" doesn't exist, creating [0005.296] Updated board info to DTB [0005.299] "pmu-board" doesn't exist, creating [0005.304] Updated board info to DTB [0005.308] "display-board" doesn't exist, creating [0005.313] Updated board info to DTB [0005.317] "reset" doesn't exist, creating [0005.321] Updated reset info to DTB [0005.325] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb4000 is_hdmi_initialised=1 [0005.364] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.376] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.389] Updated bootarg info to DTB [0005.393] Adding uuid 000000016441f8092400000019010440 to DT [0005.399] Adding eks info 0 to DT [0005.404] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0005.410] Updated memory info to DTB [0005.419] set vdd_core voltage to 1075 mv [0005.422] setting 'vdd-core' regulator to 1075000 micro volts [0005.443] Found secure-pmc; disable BPMP U-Boot 2016.07-g45dfa3dff4 (Apr 08 2020 - 18:04:08 -0700) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 1  0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 733 bytes read in 119 ms (5.9 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 5487746 bytes read in 294 ms (17.8 MiB/s) Retrieving file: /boot/Image 34265096 bytes read in 1533 ms (21.3 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb4000 is_hdmi_initialised=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 00000000831777ed Starting kernel ...