[0012.993] Enabled early print [0012.995] [L4T TegraBoot] (version @I?$ kX+) [0013.001] Processing in recovery mode [0013.005] A02 Bootrom Patch rev = 1023 [0013.008] Power-up reason: pmc por [0013.011] Established communication link with host [0014.072] NvTbootI2cWrite(): error code 0x00045100 Error while starting write transaction [0014.080] NvTbootI2cDeviceRead(): error code 0x00045001 Error while sending the offset to slave [0014.088] NvTbootI2c: Read failed for slave 0xac, offset 0x00 with error code 0x00045001 [0066.119] Enabled early print [0066.122] [L4T TegraBoot] (version @I?$ kX+) [0066.128] Processing in recovery mode [0066.131] A02 Bootrom Patch rev = 1023 [0066.135] Power-up reason: software reset [0066.139] Established communication link with host [0067.360] Odmdata from BCT: 0x000a4000 [0067.363] DebugPort= 0x3 [0067.366] SkipQspiOnly= 0x0 [0067.418] BoardId read from EEPROM/NCT: 3448 [0067.422] BoardID = 3448, SKU = 0x0 [0067.449] NvTbootInit_Porg: Setting GPIO_A6 for HDMI ... [0067.454] max77620 setting MBLPD bit [0067.458] No Battery Present [0067.461] RamCode = 0 [0067.463] Platform has DDR4 type RAM [0067.466] max77620 disabling SD1 Remote Sense [0067.471] Setting DDR voltage to 1125mv [0067.475] Serial Number of Pmic Max77663: 0x2313eb [0067.482] Entering ramdump check [0067.485] Get RamDumpCarveOut = 0x0 [0067.489] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0067.494] Last reboot was clean, booting normally! [0067.498] Sdram initialization is successful [0067.502] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0067.509] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0067.514] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0067.520] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0067.526] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0067.532] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0067.538] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0067.544] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0067.560] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0067.566] Platform-DebugCarveout: 0 [0067.569] Downloaded BCT successfully [0067.981] Downloaded Bootloader successfully [0068.036] Downloaded rp1 successfully [0068.294] MAX77620_GPIO5 configured [0068.297] CPU power rail is up [0068.300] CPU clock enabled [0068.304] Performing RAM repair [0068.307] Updating A64 Warmreset Address to 0x92c002e9 [0068.313] Enable APE clock/reset [0068.316] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0068.321] Loading Secure OS image failed. [0068.325] Set NvDecSticky Bits [0068.328] GSC2 address ff53fffc value c0edbbcc [0068.335] GSC MC Settings done [0068.339] Next binary entry address: 0x92c00258 [0068.343] BoardId: 3448 [0068.346] Overriding pmu board id with proc board id [0068.351] Display board id is not available [0068.355] Starting CPU & Halting co-processor [0070.006] [0070.007] Debug Init done [0070.011] Marked DTB cacheable [0070.013] Bootloader DTB loaded at 0x83000400 [0070.018] DeviceTree Init done [0070.031] Pinmux applied successfully [0070.035] gicd_base: 0x50041000 [0070.039] gicc_base: 0x50042000 [0070.042] Interrupts Init done [0070.046] Using base:0x60005090 & irq:208 for tick-timer [0070.051] Using base:0x60005098 for delay-timer [0070.055] platform_init_timer: DONE [0070.059] Timer(tick) Init done [0070.063] osc freq = 38400 khz [0070.067] [0070.068] Welcome to L4T Cboot [0070.071] [0070.072] Cboot Version: 00.00.2018.01-t210-a2f2e4b8 [0070.077] calling constructors [0070.080] initializing heap [0070.082] initializing threads [0070.085] initializing timers [0070.088] creating bootstrap completion thread [0070.093] top of bootstrap2() [0070.095] CPU: ARM Cortex A57 [0070.098] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0070.103] initializing platform [0070.111] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0070.115] ID LSB = 0x36, ID-CFI len = 194 bytes [0070.120] Macronix QSPI chip present [0070.123] SPI device register [0070.126] init boot device [0070.128] allocating memory for boot device(SPI) [0070.133] registering boot device [0070.142] sdmmc node status = okay [0070.146] sdcard instance = 0 [0070.149] sdmmc cd-inverted [0070.151] sdcard gpio handle 0x5b [0070.154] sdcard gpio pin 0xc9 [0070.157] sdcard gpio flags 0x0 [0070.160] vmmc-supply 0x9d [0070.163] Instance: 0 [0070.165] Allocating memory for context [0070.169] enabling clock [0070.171] sd card init [0070.174] Check card present and stable [0070.177] Send command 0 [0070.184] Error in command_complete 18001 int_status [0070.191] Error in command_complete 18001 int_status [0070.198] Error in command_complete 18001 int_status [0070.203] sending the command failed 0xffffffec in sdmmc_send_command at 109 [0070.210] Sending CMD_SD_SEND_IF_COND failed [0070.214] Retrying CMD0/CMD8 sequence ... [0070.218] Send command 0 [0070.224] Error in command_complete 18001 int_status [0070.231] Error in command_complete 18001 int_status [0070.238] Error in command_complete 18001 int_status [0070.243] sending the command failed 0xffffffec in sdmmc_send_command at 109 [0070.250] Sending CMD_SD_SEND_IF_COND failed [0070.254] Identify SD card failed 0xffffffec in sdmmc_init at 1127 [0070.270] error opening sdcard-0 [0070.273] of_register: registering tegra_udc to of_hal [0070.278] of_register: registering inv20628-driver to of_hal [0070.284] of_register: registering ads1015-driver to of_hal [0070.290] of_register: registering lp8557-bl-driver to of_hal [0070.295] of_register: registering bq2419x_charger to of_hal [0070.301] of_register: registering bq27441_fuel_gauge to of_hal [0070.313] gpio framework initialized [0070.316] of_register: registering tca9539_gpio to of_hal [0070.322] of_register: registering tca9539_gpio to of_hal [0070.327] of_register: registering i2c_bus_driver to of_hal [0070.332] of_register: registering i2c_bus_driver to of_hal [0070.338] of_register: registering i2c_bus_driver to of_hal [0070.344] pmic framework initialized [0070.347] of_register: registering max77620_pmic to of_hal [0070.353] regulator framework initialized [0070.357] of_register: registering tps65132_bl_driver to of_hal [0070.362] initializing target [0070.368] gpio_driver_register: register 'tegra_gpio_driver' driver [0070.377] board ID = D78, board SKU = 0 [0070.381] Skipping Z3! [0070.386] fixed regulator driver initialized [0070.403] initializing OF layer [0070.407] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0070.425] I2C Bus Init done [0070.428] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0070.438] I2C Bus Init done [0070.441] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0070.451] I2C Bus Init done [0070.453] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0070.464] I2C Bus Init done [0070.466] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0070.477] I2C Bus Init done [0070.479] of_children_init: Ops found for compatible string maxim,max77620 [0070.490] max77620_init using irq 118 [0070.495] register 'maxim,max77620' pmic [0070.499] gpio_driver_register: register 'max77620-gpio' driver [0070.505] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0070.516] I2C Bus Init done [0070.520] Applying platform configs [0070.526] platform-init is not present. Skipping [0070.531] calling apps_init() [0070.534] Failed to open "sd0" for publishing partitions [0070.539] Proceeding to flashing Server [0070.543] usbdcd_reinit Initialize driver to use already enumerated device [0070.550] nv3p_priv_usbf_open USB configuration success [0070.636] populate_storage_info: failed to open sd0 ! [0070.641] populate_platform_info: failed to populate storage info [0070.647] pre_process_oem_commands: failed to populate platform info [0070.654] pre_process_oem_commands: failed to process oem commands [0070.660] oem_commands: processing oem command failed